Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost cross endian support from Michael Tsirkin:
"I have just queued some more bugfix patches today but none fix
regressions and none are related to these ones, so it looks like a
good time for a merge for -rc1.
The motivation for this is support for legacy BE guests on the new LE
hosts. There are two redeeming properties that made me merge this:
- It's a trivial amount of code: since we wrap host/guest accesses
anyway, almost all of it is well hidden from drivers.
- Sane platforms would never set flags like VHOST_CROSS_ENDIAN_LEGACY,
and when it's clear, there's zero overhead (as some point it was
tested by compiling with and without the patches, got the same
stripped binary).
Maybe we could create a Kconfig symbol to enforce the second point:
prevent people from enabling it eg on x86. I will look into this"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-pci: alloc only resources actually used.
macvtap/tun: cross-endian support for little-endian hosts
vhost: cross-endian support for legacy devices
virtio: add explicit big-endian support to memory accessors
vhost: introduce vhost_is_little_endian() helper
vringh: introduce vringh_is_little_endian() helper
macvtap: introduce macvtap_is_little_endian() helper
tun: add tun_is_little_endian() helper
virtio: introduce virtio_is_little_endian() helper
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace updates from Eric Biederman:
"Long ago and far away when user namespaces where young it was realized
that allowing fresh mounts of proc and sysfs with only user namespace
permissions could violate the basic rule that only root gets to decide
if proc or sysfs should be mounted at all.
Some hacks were put in place to reduce the worst of the damage could
be done, and the common sense rule was adopted that fresh mounts of
proc and sysfs should allow no more than bind mounts of proc and
sysfs. Unfortunately that rule has not been fully enforced.
There are two kinds of gaps in that enforcement. Only filesystems
mounted on empty directories of proc and sysfs should be ignored but
the test for empty directories was insufficient. So in my tree
directories on proc, sysctl and sysfs that will always be empty are
created specially. Every other technique is imperfect as an ordinary
directory can have entries added even after a readdir returns and
shows that the directory is empty. Special creation of directories
for mount points makes the code in the kernel a smidge clearer about
it's purpose. I asked container developers from the various container
projects to help test this and no holes were found in the set of mount
points on proc and sysfs that are created specially.
This set of changes also starts enforcing the mount flags of fresh
mounts of proc and sysfs are consistent with the existing mount of
proc and sysfs. I expected this to be the boring part of the work but
unfortunately unprivileged userspace winds up mounting fresh copies of
proc and sysfs with noexec and nosuid clear when root set those flags
on the previous mount of proc and sysfs. So for now only the atime,
read-only and nodev attributes which userspace happens to keep
consistent are enforced. Dealing with the noexec and nosuid
attributes remains for another time.
This set of changes also addresses an issue with how open file
descriptors from /proc/<pid>/ns/* are displayed. Recently readlink of
/proc/<pid>/fd has been triggering a WARN_ON that has not been
meaningful since it was added (as all of the code in the kernel was
converted) and is not now actively wrong.
There is also a short list of issues that have not been fixed yet that
I will mention briefly.
It is possible to rename a directory from below to above a bind mount.
At which point any directory pointers below the renamed directory can
be walked up to the root directory of the filesystem. With user
namespaces enabled a bind mount of the bind mount can be created
allowing the user to pick a directory whose children they can rename
to outside of the bind mount. This is challenging to fix and doubly
so because all obvious solutions must touch code that is in the
performance part of pathname resolution.
As mentioned above there is also a question of how to ensure that
developers by accident or with purpose do not introduce exectuable
files on sysfs and proc and in doing so introduce security regressions
in the current userspace that will not be immediately obvious and as
such are likely to require breaking userspace in painful ways once
they are recognized"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
vfs: Remove incorrect debugging WARN in prepend_path
mnt: Update fs_fully_visible to test for permanently empty directories
sysfs: Create mountpoints with sysfs_create_mount_point
sysfs: Add support for permanently empty directories to serve as mount points.
kernfs: Add support for always empty directories.
proc: Allow creating permanently empty directories that serve as mount points
sysctl: Allow creating permanently empty directories that serve as mountpoints.
fs: Add helper functions for permanently empty directories.
vfs: Ignore unlocked mounts in fs_fully_visible
mnt: Modify fs_fully_visible to deal with locked ro nodev and atime
mnt: Refactor the logic for mounting sysfs and proc in a user namespace
Merge tag 'remoteproc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc updates from Ohad Ben-Cohen:
- remoteproc fixes/cleanups from Suman Anna
- new remoteproc TI Wakeup M3 driver from Dave Gerlach
- remoteproc core support for TI's Wakeup M3 driver from both Dave and Suman
- tiny remoteproc build fix from myself
* tag 'remoteproc-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: fix !CONFIG_OF build breakage
remoteproc/wkup_m3: add a remoteproc driver for TI Wakeup M3
Documentation: dt: add bindings for TI Wakeup M3 processor
remoteproc: add a rproc ops for performing address translation
remoteproc: introduce rproc_get_by_phandle API
remoteproc: fix various checkpatch warnings
remoteproc/davinci: fix quoted split string checkpatch warning
remoteproc/ste: add blank lines after declarations
Merge tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock
Pull hwspinlock updates from Ohad Ben-Cohen:
- hwspinlock core DT support from Suman Anna
- OMAP hwspinlock DT support from Suman Anna
- QCOM hwspinlock DT support from Bjorn Andersson
- a new CSR atlas7 hwspinlock driver from Wei Chen
- CSR atlas7 hwspinlock DT binding document from Wei Chen
- a tiny QCOM hwspinlock driver fix from Bjorn Andersson
* tag 'hwspinlock-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/hwspinlock:
hwspinlock: qcom: Correct msb in regmap_field
DT: hwspinlock: add the CSR atlas7 hwspinlock bindings document
hwspinlock: add a CSR atlas7 driver
hwspinlock: qcom: Add support for Qualcomm HW Mutex block
DT: hwspinlock: Add binding documentation for Qualcomm hwmutex
hwspinlock/omap: add support for dt nodes
Documentation: dt: add the omap hwspinlock bindings document
hwspinlock/core: add device tree support
Documentation: dt: add common bindings for hwspinlock
- suspicious RCU usage warning
- BPF (out of bounds array read and endianness conversion)
- perf (of_node usage after of_node_put, cpu_pmu->plat_device
assignment)
- huge pmd/pud check for value 0
- rate-limiting should only take unhandled signals into account
Clean-up:
- incorrect use of pgprot_t type
- unused header include
- __init annotation to arm_cpuidle_init
- pr_debug instead of pr_error for disabled GICC entries in
ACPI/MADT"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix show_unhandled_signal_ratelimited usage
ARM64 / SMP: Switch pr_err() to pr_debug() for disabled GICC entry
arm64: cpuidle: add __init section marker to arm_cpuidle_init
arm64: Don't report clear pmds and puds as huge
arm64: perf: fix unassigned cpu_pmu->plat_device when probing PMU PPIs
arm64: perf: Don't use of_node after putting it
arm64: fix incorrect use of pgprot_t variable
arm64/hw_breakpoint.c: remove unnecessary header
arm64: bpf: fix endianness conversion bugs
arm64: bpf: fix out-of-bounds read in bpf2a64_offset()
ARM64: smp: Fix suspicious RCU usage with ipi tracepoints
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull more hwmon updates from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627ehf) Use swap() in w82627ehf_swap_tempreg()
hwmon: Document which I2C addresses can be probed
hwmon: (w83792d) Additional PWM outputs support
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Mainly sending this off now for the writeback fixes, since they fix a
real regression introduced with the cgroup writeback changes. The
NVMe fix could wait for next pull for this series, but it's simple
enough that we might as well include it.
This contains:
- two cgroup writeback fixes from Tejun, fixing a user reported issue
with luks crypt devices hanging when being closed.
- NVMe error cleanup fix from Jon Derrick, fixing a case where we'd
attempt to free an unregistered IRQ"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Fix irq freeing when queue_request_irq fails
writeback: don't drain bdi_writeback_congested on bdi destruction
writeback: don't embed root bdi_writeback_congested in bdi_writeback
Commit 5ad797a4be7 introduced ratelimited usage for
'unhandled_signal' messages.
The commit checks the ratelimit irrespective of whether
the signal is handled or not, which is wrong and leads
to false reports like the below in dmesg :
__do_user_fault: 127 callbacks suppressed
Do the ratelimit check only if the signal is unhandled.
Fixes: 5ad797a4be70 ("arm64: use private ratelimit state along with show_unhandled_signals") Cc: Vladimir Murzin <Vladimir.Murzin@arm.com> Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM64 / SMP: Switch pr_err() to pr_debug() for disabled GICC entry
It is normal that firmware presents GICC entry or entries (processors)
with disabled flag in ACPI MADT, taking a system of 16 cpus for example,
ACPI firmware may present 8 ebabled first with another 8 cpus disabled
in MADT, the disabled cpus can be hot-added later.
Firmware may also present more cpus than the hardware actually has, but
disabled the unused ones, and easily enable it when the hardware has such
cpus to make the firmware code scalable.
So that's not an error for disabled cpus in MADT, we can switch pr_err()
to pr_debug() to make the boot a little quieter by default.
Since hwid for disabled cpus often are invalid, and we check invalid hwid
first in the code, for use case that hot add cpus later will be filtered
out and will not be counted in possible cups, so move this check before
the hwid one to prepare the code to count for disabeld cpus when cpu
hot-plug is introduced.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by: Al Stone <ahs3@redhat.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"Additional ACPICA material for v4.2-rc1
This will update the ACPICA code in the kernel to upstream revision 20150619 (a bug-fix release mostly including stable-candidate fixes)
and restore an earlier ACPICA commit that had to be reverted due to a
regression introduced by it (the regression is addressed by
blacklisting the only known system affected by it to date).
The only new feature added by this update is the support for
overriding objects in the ACPI namespace and a new ACPI table that can
be used for that called the Override System Definition Table (OSDT).
That should allow us to "patch" the ACPI namespace built from
incomplete or incorrect ACPI System Definition tables (DSDT, SSDT)
during system startup without the need to provide replacements for all
of those tables in the future.
Specifics:
- Fix system resume problems related to 32-bit and 64-bit versions of
the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng)
- Fix double initialization of the FACS (Lv Zheng)
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit)
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo)
- Add support for overriding objects in the ACPI namespace to ACPICA
and OSDT support (Lv Zheng, Bob Moore, Zhang Rui)
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore)
- Restore the commit modifying _REV to always return "2" (as required
by ACPI 6) and add a blacklisting mechanism for systems that may be
affected by that change (Rafael J Wysocki)
* tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
Revert 'Revert "ACPICA: Permanently set _REV to the value '2'."'
ACPI / init: Make it possible to override _REV
ACPICA: Update version to 20150619
ACPICA: Comment update, no functional change
ACPICA: Update TPM2 ACPI table
ACPICA: Update definitions for the TCPA and TPM2 ACPI tables
ACPICA: Split C library prototypes to new header
ACPICA: De-macroize calls to standard C library functions
ACPI / acpidump: Update acpidump manual
ACPICA: acpidump: Convert the default behavior to dump from /sys/firmware/acpi/tables
ACPICA: acpidump: Allow customized tables to be dumped without accessing /dev/mem
ACPICA: Cleanup output for the ASL Debug object
ACPICA: Update for acpi_install_table memory types
ACPICA: Namespace: Change namespace override to avoid node deletion
ACPICA: Namespace: Add support of OSDT table
ACPICA: Namespace: Add support to allow overriding objects
ACPICA: ACPI 6.0: Add values for MADT GIC version field
ACPICA: Utilities: Add _CLS processing
ACPICA: Add dragon_fly support to unix file mapping file
ACPICA: EFI: Add EFI interface definitions to eliminate dependency of GNU EFI
...
Revert 'Revert "ACPICA: Permanently set _REV to the value '2'."'
Revert commit b9f2ec7c56f6 (Revert "ACPICA: Permanently set _REV to
the value '2'.) as the regression introduced by commit e3abe948c067
reverted by it is now addressed via a blacklist entry.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The platform firmware on some systems expects Linux to return "5" as
the supported ACPI revision which makes it expose system configuration
information in a special way.
For example, based on what ACPI exports as the supported revision,
Dell XPS 13 (2015) configures its audio device to either work in HDA
mode or in I2S mode, where the former is supposed to be used on Linux
until the latter is fully supported (in the kernel as well as in user
space).
Since ACPI 6 mandates that _REV should return "2" if ACPI 2 or later
is supported by the OS, a subsequent change will make that happen, so
make it possible to override that on systems where "5" is expected to
be returned for Linux to work correctly one them (such as the Dell
machine mentioned above).
Original-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Just a few kbuild core commits this time:
- kallsyms fix for CONFIG_XIP_KERNEL
- bashisms in scripts/link-vmlinux.sh fixed
- workaround to make DEBUG_INFO_REDUCED more useful yet still space
efficient
- clang is not wrongly detected when cross-compiling"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: include core debug info when DEBUG_INFO_REDUCED
scripts: link-vmlinux: Don't pass page offset to kallsyms if XIP Kernel
scripts: fix link-vmlinux.sh bash-ism
Makefile: Fix detection of clang when cross-compiling
Merge branch 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kconfig updates from Michal Marek:
- kconfig conditions can use usual less/greater than comparisons
- kconfig warns about stray characters in Kconfig files
- bogus expression simplification removed
- some minor fixes
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: re-generate *.c_shipped files after previous change
kconfig: allow use of relations other than (in)equality
kconfig: don't silently ignore unhandled characters
kconfig: Wrap long "make help" text lines
scripts/kconfig/Makefile: Cosmetic fixes
scripts/kconfig/Makefile: Fix spelling of Qt
Kconfig: Remove bad inference rules expr_eliminate_dups2()
Merge tag 'hwmon-for-linus-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two patches headed for stable:
- Fix broken output scaling in mcp3021 driver
- Fix attribute visibility in nct7802 driver
One regression:
- Fix name attribute in dell-smm-hwmon driver"
* tag 'hwmon-for-linus-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (mcp3021) Fix broken output scaling
hwmon: (nct7802) fix visibility of temp3
hwmon: (dell-smm-hwmon) Use a valid name attribute
Merge tag 'please-pull-put_kernel_page' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 boot noise reduction fix from Tony Luck:
"Remove some boot noise from a now-invalid check that pages are
reserved"
* tag 'please-pull-put_kernel_page' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Drop debug test/printk that some special pages are marked reserved
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
Merge branch 'drm-next-4.2' of git://people.freedesktop.org/~agd5f/linux
Pull radeon and amdgpu fixes from Alex Deucher:
"First round of fixes for 4.2 for radeon and amdgpu. Stuff all over
the place:
- hibernation, suspend fixes for radeon and amdgpu
- radeon audio fix
- amdgpu ioctl optimzations and fixes
- amdgpu VCE cs checker improvements
- misc bug fixes"
[ Dave on vacation, pulling directly ]
* 'drm-next-4.2' of git://people.freedesktop.org/~agd5f/linux: (30 commits)
drm/radeon: only check the sink type on DP connectors
drm/amdgpu: add flag to delay VM updates
drm/amdgpu: add optional dependencies to the CS IOCTL v2
drm/amdgpu: recreate fence from user seq
gpu/drm/amdgpu: Fix build when CONFIG_DEBUG_FS is not set
Revert "drm/radeon: dont switch vt on suspend"
drm/amdgpu: disable enable_nb_ps_policy temporarily
drm/amdgpu: correct define SMU_EnabledFeatureScoreboard_SclkDpmOn
drm/amdgpu: allocate ip_block_enabled memory in common code
drm/amdgpu: remove unnecessary check before kfree
drm/amdgpu: use kzalloc for allocating one thing
drm/radeon: fix adding all VAs to the freed list on remove v2
drm/amdgpu: add chunk id validity check
drm/amdgpu: fix crash on invalid CS IOCTL
drm/amdgpu: reset wptr at cp compute resume (v2)
drm/amdgpu: check VCE feedback and bitstream index
drm/amdgpu: make VCE handle check more strict
drm/amdgpu: check VCE relocation buffer range
drm/amdgpu: silence invalid error message
drm/amdgpu: fix wrong type
...
Merge tag 'drm-intel-next-fixes-2015-07-02' of git://anongit.freedesktop.org/drm-intel
Pull intel drm fixes from Jani Nikula:
"Almost all of it is regression fixes all around, with cc: stable, and
then there's Ander's fix for one of the warnings you reported. We're
still working on the rest"
[ Dave is on vacation, and Jani is heading out on vacation too ]
* tag 'drm-intel-next-fixes-2015-07-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Clear pipe's pll hw state in hsw_dp_set_ddi_pll_sel()
drm/i915: fix backlight after resume on 855gm
agp/intel: Fix typo in needs_ilk_vtd_wa()
drm/i915/ppgtt: Break loop in gen8_ppgtt_clear_range failure path
drm/i915: Fix IPS related flicker
Tony Luck [Thu, 2 Jul 2015 19:12:53 +0000 (12:12 -0700)]
[IA64] Drop debug test/printk that some special pages are marked reserved
In commit 982613357f68 "mm: meminit: only set page reserved in the memblock region"
we dropped setting the reserved bits for all pages. This results in some warnings
on ia64:
put_kernel_page: page at 0xe000000005588000 not in reserved memory
put_kernel_page: page at 0xe000000005588000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
the two different pages match up with two objects from the loaded kernel
that get mapped by arch/ia64/mm/init.c:setup_gate()
In a discussion with Mel Gorman:
http://lkml.kernel.org/r/20150526102219.GB13750%40suse.de
he suggested that while the preferred approach might be to
set the reserved bit for these pages, it would also be OK
to just drop the test:
"as it's a debugging check that is ia-64 specific"
After hunting around a bit and failin to find a good place to mark these
pages as reserved - I decided to just delete the test.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"We have a pile of bug fixes from Ilya, including a few patches that
sync up the CRUSH code with the latest from userspace.
There is also a long series from Zheng that fixes various issues with
snapshots, inline data, and directory fsync, some simplification and
improvement in the cap release code, and a rework of the caching of
directory contents.
To top it off there are a few small fixes and cleanups from Benoit and
Hong"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (40 commits)
rbd: use GFP_NOIO in rbd_obj_request_create()
crush: fix a bug in tree bucket decode
libceph: Fix ceph_tcp_sendpage()'s more boolean usage
libceph: Remove spurious kunmap() of the zero page
rbd: queue_depth map option
rbd: store rbd_options in rbd_device
rbd: terminate rbd_opts_tokens with Opt_err
ceph: fix ceph_writepages_start()
rbd: bump queue_max_segments
ceph: rework dcache readdir
crush: sync up with userspace
crush: fix crash from invalid 'take' argument
ceph: switch some GFP_NOFS memory allocation to GFP_KERNEL
ceph: pre-allocate data structure that tracks caps flushing
ceph: re-send flushing caps (which are revoked) in reconnect stage
ceph: send TID of the oldest pending caps flush to MDS
ceph: track pending caps flushing globally
ceph: track pending caps flushing accurately
libceph: fix wrong name "Ceph filesystem for Linux"
ceph: fix directory fsync
...
Merge tag 'nfs-for-4.2-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable patches:
- Fix a crash in the NFSv4 file locking code.
- Fix an fsync() regression, where we were failing to retry I/O in
some circumstances.
- Fix an infinite loop in NFSv4.0 OPEN stateid recovery
- Fix a memory leak when an attempted pnfs fails.
- Fix a memory leak in the backchannel code
- Large hostnames were not supported correctly in NFSv4.1
- Fix a pNFS/flexfiles bug that was impeding error reporting on I/O.
- Fix a couple of credential issues in pNFS/flexfiles
Bugfixes + cleanups:
- Open flag sanity checks in the NFSv4 atomic open codepath
- More NFSv4 delegation related bugfixes
- Various NFSv4.1 backchannel bugfixes and cleanups
- Fix the NFS swap socket code
- Various cleanups of the NFSv4 SETCLIENTID and EXCHANGE_ID code
- Fix a UDP transport deadlock issue
Features:
- More RDMA client transport improvements
- NFSv4.2 LAYOUTSTATS functionality for pnfs flexfiles"
* tag 'nfs-for-4.2-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (87 commits)
nfs: Remove invalid tk_pid from debug message
nfs: Remove invalid NFS_ATTR_FATTR_V4_REFERRAL checking in nfs4_get_rootfh
nfs: Drop bad comment in nfs41_walk_client_list()
nfs: Remove unneeded micro checking of CONFIG_PROC_FS
nfs: Don't setting FILE_CREATED flags always
nfs: Use remove_proc_subtree() instead remove_proc_entry()
nfs: Remove unused argument in nfs_server_set_fsinfo()
nfs: Fix a memory leak when meeting an unsupported state protect
nfs: take extra reference to fl->fl_file when running a LOCKU operation
NFSv4: When returning a delegation, don't reclaim an incompatible open mode.
NFSv4.2: LAYOUTSTATS is optional to implement
NFSv4.2: Fix up a decoding error in layoutstats
pNFS/flexfiles: Fix the reset of struct pgio_header when resending
pNFS/flexfiles: Turn off layoutcommit for servers that don't need it
pnfs/flexfiles: protect ktime manipulation with mirror lock
nfs: provide pnfs_report_layoutstat when NFS42 is disabled
nfs: verify open flags before allowing open
nfs: always update creds in mirror, even when we have an already connected ds
nfs: fix potential credential leak in ff_layout_update_mirror_cred
pnfs/flexfiles: report layoutstat regularly
...
Merge branch 'overlayfs-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This relaxes the requirements on the lower layer filesystem: now ones
that implement .d_revalidate, such as NFS, can be used.
Upper layer filesystems still has the "no .d_revalidate" requirement.
Also a bad interaction with jffs2 locking has been fixed"
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi:
"This is the start of improving fuse scalability.
An input queue and a processing queue is split out from the monolithic
fuse connection, each of those having their own spinlock. The end of
the patchset adds the ability to clone a fuse connection. This means,
that instead of having to read/write requests/answers on a single fuse
device fd, the fuse daemon can have multiple distinct file descriptors
open. Each of those can be used to receive requests and send answers,
currently the only constraint is that a request must be answered on
the same fd as it was read from.
This can be extended further to allow binding a device clone to a
specific CPU or NUMA node.
Based on a patchset by Srinivas Eeda and Ashish Samant. Thanks to
Ashish for the review of this series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: (40 commits)
fuse: update MAINTAINERS entry
fuse: separate pqueue for clones
fuse: introduce per-instance fuse_dev structure
fuse: device fd clone
fuse: abort: no fc->lock needed for request ending
fuse: no fc->lock for pqueue parts
fuse: no fc->lock in request_end()
fuse: cleanup request_end()
fuse: request_end(): do once
fuse: add req flag for private list
fuse: pqueue locking
fuse: abort: group pqueue accesses
fuse: cleanup fuse_dev_do_read()
fuse: move list_del_init() from request_end() into callers
fuse: duplicate ->connected in pqueue
fuse: separate out processing queue
fuse: simplify request_wait()
fuse: no fc->lock for iqueue parts
fuse: allow interrupt queuing without fc->lock
fuse: iqueue locking
...
Merge tag 'module-misc-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull init.h/module.h fragility fixes from Paul Gortmaker:
"Fixup various init.h misuses that are fragile wrt code moving to
module.h
What started as a removal of no longer required include <linux/init.h>
due to the earlier __cpuinit and __devinit removal led to the
observation that some module specfic support was living in init.h
itself, thus preventing the full removal from introducing compile
regressions.
This series includes a few final fixups needed prior to the relocation
of the modular init code from <init.h> to <module.h>. These are
things that weren't easily categorized into any of the other previous
series categories already requested for pull.
That said, each fixup branch (including this one) is independent and
there are no ordering constraints. Only the final code relocation
(which is NOT in this pull) requires that all my cleanup branches be
merged first"
* tag 'module-misc-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
tile: add init.h to usb.c to avoid compile failure
arm: fix implicit #include <linux/init.h> in entry asm.
x86: replace __init_or_module with __init in non-modular vsmp_64.c
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
Merge tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part two from Paul Gortmaker:
"Replace module_init with appropriate alternate initcall in non
modules.
This series converts non-modular code that is using the module_init()
call to hook itself into the system to instead use one of our
alternate priority initcalls.
Unlike the previous series that used device_initcall and hence was a
runtime no-op, these commits change to one of the alternate initcalls,
because (a) we have them and (b) it seems like the right thing to do.
For example, it would seem logical to use arch_initcall for arch
specific setup code and fs_initcall for filesystem setup code.
This does mean however, that changes in the init ordering will be
taking place, and so there is a small risk that some kind of implicit
init ordering issue may lie uncovered. But I think it is still better
to give these ones sensible priorities than to just assign them all to
device_initcall in order to exactly preserve the old ordering.
Thad said, we have already made similar changes in core kernel code in
commit 0e22281aa123 ("kernel: audit/fix non-modular users of
module_init in core code") without any regressions reported, so this
type of change isn't without precedent. It has also got the same
local testing and linux-next coverage as all the other pull requests
that I'm sending for this merge window have got.
Once again, there is an unused module_exit function removal that shows
up as an outlier upon casual inspection of the diffstat"
* tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling
x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling
mm/page_owner.c: use late_initcall to hook in enabling
lib/list_sort: use late_initcall to hook in self tests
arm: use subsys_initcall in non-modular pl320 IPC code
powerpc: don't use module_init for non-modular core hugetlb code
powerpc: use subsys_initcall for Freescale Local Bus
x86: don't use module_init for non-modular core bootflag code
netfilter: don't use module_init/exit in core IPV4 code
fs/notify: don't use module_init for non-modular inotify_user code
mm: replace module_init usages with subsys_initcall in nommu.c
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
Merge tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
Merge tag 'cpuinit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull __cpuinit removal from Paul Gortmaker:
"Remove __cpuinit macros and users.
We removed the __cpuinit stuff in 3.11-rc1 with commit c095a79d24e8
("init.h: remove __cpuinit sections from the kernel") but we left some
no-op stubs as a courtesy to unmerged code.
Here we get rid of the stubs as well, since (as can be seen in these
changes) they are enabling use cases to sneak back in, primarily from
older BSP code that has been living out of tree for some time prior to
getting mainlined. So we get rid of these "new" users 1st and then
get rid of the stubs.
Obviously, getting rid of the stubs can't happen until all the users
are gone, so I had to keep this together as a series, even though some
of these commits since got picked up into maintainers trees as well.
The nature of this change is such that it should have zero impact on
the generated runtime.
This is one of several independent cleanup branches aimed at enabling
better organization in the init.h and module.h code. They have been
getting coverage in the linux-next tree for the last month, in
addition to my local testing, which also covers approximately a half
dozen or more architectures"
* tag 'cpuinit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
init: delete the __cpuinit related stubs
kernel/cpu.c: remove new instance of __cpuinit that crept back in
sched/core: remove __cpuinit section tag that crept back in.
mips/mm/tlbex: remove new instance of __cpuinit that crept back in
mips/c-r4k: remove legacy __cpuinit section that crept in
mips/bcm77xx: remove legacy __cpuinit sections that crept in
mips/ath25: remove legacy __cpuinit section that crept in
arm/mach-hisi: remove legacy __CPUINIT section that crept in
arm/mach-rockchip: remove legacy __cpuinit section that crept in
arm/mach-mvebu: remove legacy __cpuinit sections that crept in
arm/mach-keystone: remove legacy __cpuinit sections that crept in
Jon Derrick [Tue, 30 Jun 2015 17:22:52 +0000 (11:22 -0600)]
NVMe: Fix irq freeing when queue_request_irq fails
Fixes an issue when queue_reuest_irq fails in nvme_setup_io_queues. This
patch initializes all vectors to -1 and resets the vector to -1 in the
case of a failure in queue_request_irq. This avoids the free_irq in
nvme_suspend_queue if the queue did not get an irq.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com> Signed-off-by: Jens Axboe <axboe@fb.com>
writeback: don't drain bdi_writeback_congested on bdi destruction
0bfd3047cfb4 ("writeback: make backing_dev_info host cgroup-specific
bdi_writebacks") made bdi (backing_dev_info) host per-cgroup wb's
(bdi_writeback's). As the congested state needs to be per-wb and
referenced from blkcg side and multiple wbs, the patch made all
non-root cong's (bdi_writeback_congested's) reference counted and
indexed on bdi.
When a bdi is destroyed, cgwb_bdi_destroy() tries to drain all
non-root cong's; however, this can hang indefinitely because wb's can
also be referenced from blkcg_gq's which are destroyed after bdi
destruction is complete.
This patch fixes the bug by updating bdi destruction to not wait for
cong's to drain. A cong is unlinked from bdi->cgwb_congested_tree on
bdi destuction regardless of its reference count as the bdi may go
away any point after destruction. wb_congested_put() checks whether
the cong is already unlinked on release.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Jon Christopherson <jon@jons.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=100681 Fixes: 0bfd3047cfb4 ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks") Tested-by: Jon Christopherson <jon@jons.org> Signed-off-by: Jens Axboe <axboe@fb.com>
writeback: don't embed root bdi_writeback_congested in bdi_writeback
0bfd3047cfb4 ("writeback: make backing_dev_info host cgroup-specific
bdi_writebacks") made bdi (backing_dev_info) host per-cgroup wb's
(bdi_writeback's). As the congested state needs to be per-wb and
referenced from blkcg side and multiple wbs, the patch made all
non-root cong's (bdi_writeback_congested's) reference counted and
indexed on bdi.
When a bdi is destroyed, cgwb_bdi_destroy() tries to drain all
non-root cong's; however, this can hang indefinitely because wb's can
also be referenced from blkcg_gq's which are destroyed after bdi
destruction is complete.
To fix the bug, bdi destruction will be updated to not wait for cong's
to drain, which naturally means that cong's may outlive the associated
bdi. This is fine for non-root cong's but is problematic for the root
cong's which are embedded in their bdi's as they may end up getting
dereferenced after the containing bdi's are freed.
This patch makes root cong's behave the same as non-root cong's. They
are no longer embedded in their bdi's but allocated separately during
bdi initialization, indexed and reference counted the same way.
* As cong handling is the same for all wb's, wb->congested
initialization is moved into wb_init().
* When !CONFIG_CGROUP_WRITEBACK, there was no indexing or refcnting.
bdi->wb_congested is now a pointer pointing to the root cong
allocated during bdi init and minimal refcnting operations are
implemented.
* The above makes root wb init paths diverge depending on
CONFIG_CGROUP_WRITEBACK. root wb init is moved to cgwb_bdi_init().
This patch in itself shouldn't cause any consequential behavior
differences but prepares for the actual fix.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Jon Christopherson <jon@jons.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=100681 Tested-by: Jon Christopherson <jon@jons.org>
Added <linux/slab.h> include to backing-dev.h for kfree() definition.
Tomi Valkeinen [Tue, 30 Jun 2015 09:23:45 +0000 (12:23 +0300)]
OMAPDSS: fix probing if rfbi device is enabled
After the commit af63cbf81023c5efc9392e0405224371f2c153dc ("OMAPDSS:
componentize omapdss") the dss core device will wait until all the
subdevices have been successfully probed. However, we don't have a
working driver for RFBI, so if RFBI device exists, omapdss will never
get probed.
All the .dtsi files set RFBI as disabled, except am4372.dtsi. This
causes omapdss probe to not finish on AM4 devices.
This patch makes omapdss driver skip adding rfbi device as a
subcomponent, solving the issue.
This should be reverted when we have a working RFBI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reported-by: Felipe Balbi <balbi@ti.com>
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree updates from Grant Likely:
"A whole lot of bug fixes.
Nothing stands out here except the ability to enable CONFIG_OF on
every architecture, and an import of a newer version of dtc"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (22 commits)
of/irq: Rename "intc_desc" to "of_intc_desc" to fix OF on sh
of/irq: Fix pSeries boot failure
Documentation: DT: Fix a typo in the filename "lantiq,<chip>-pinumx.txt"
of: define of_find_node_by_phandle for !CONFIG_OF
of/address: use atomic allocation in pci_register_io_range()
of: Add vendor prefix for Zodiac Inflight Innovations
dt/fdt: add empty versions of early_init_dt_*_memory_arch
of: clean-up unnecessary libfdt include paths
of: make unittest select OF_EARLY_FLATTREE instead of depend on it
of: make CONFIG_OF user selectable
MIPS: prepare for user enabling of CONFIG_OF
of/fdt: fix argument name and add comments of unflatten_dt_node()
of: return NUMA_NO_NODE from fallback of_node_to_nid()
tps6507x.txt: Remove executable permission
of/overlay: Grammar s/an negative/a negative/
of/fdt: Make fdt blob input parameters of unflatten functions const
of: add helper function to retrive match data
of: Grammar s/property exist/property exists/
of: Move OF flags to be visible even when !CONFIG_OF
scripts/dtc: Update to upstream version 9d3649bd3be245c9
...
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- new driver for ST's LPC Watchdog
- new driver for Conexant Digicolor CX92755 SoC
- new driver for DA9062 watchdog
- Addition of the watchdog registration deferral mechanism
- several improvements on omap_wdt
- several improvements and reboot-support for imgpdc_wdt
- max63xx_wdt improvements
- imx2_wdt improvements
- dw_wdt improvements
- and other small improvements and fixes"
* git://www.linux-watchdog.org/linux-watchdog: (37 commits)
watchdog: omap_wdt: early_enable module parameter
watchdog: gpio_wdt: Add option for early registration
watchdog: watchdog_core: Add watchdog registration deferral mechanism
watchdog: max63xx: dynamically allocate device
watchdog: imx2_wdt: Disable previously acquired clock on error path
watchdog: imx2_wdt: Check for clk_prepare_enable() error
watchdog: hpwdt: Add support for WDIOC_SETOPTIONS
watchdog: docs: omap_wdt also understands nowayout
watchdog: omap_wdt: implement get_timeleft
watchdog: da9062: DA9062 watchdog driver
watchdog: imx2_wdt: set watchdog parent device
watchdog: mena21_wdt: Fix possible NULL pointer dereference
watchdog: dw_wdt: keepalive the watchdog at write time
watchdog: dw_wdt: No need for a spinlock
watchdog: imx2_wdt: also set wdog->timeout to new_timeout
watchdog: Allow compile test of GPIO consumers if !GPIOLIB
watchdog: cadence: Add dependency on HAS_IOMEM
watchdog: max63xx_wdt: Constify platform_device_id
watchdog: MAX63XX_WATCHDOG does not depend on ARM
watchdog: imgpdc: Add some documentation about the timeout
...
Merge tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
Merge tag 'platform-drivers-x86-v4.2-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Fairly routine update for platform-drivers-x86.
Mostly fixes and cleanups, with a significant refactoring of toshiba*
drivers. Includes the addition of the dell-rbtn driver.
Details:
asus-wmi:
- fan control
dell*:
- add Dell airplane mode switch driver
ideapad-laptop:
- platform rfkill fixes, and regression fix
pvpanic:
- handle missing _STA correctly
toshiba*:
- rafactor bluetooth support
- haps documentation
- driver cleanup
other:
- Use acpi_video_unregister_backlight instead of
acpi_video_unregister in serveral drivers.
- Orphan msi-wmi.
* tag 'platform-drivers-x86-v4.2-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (24 commits)
MAINTAINERS: Orphan x86 driver msi-wmi
ideapad: fix software rfkill setting
dell-laptop: Use dell-rbtn instead i8042 filter when possible
dell-rbtn: Export notifier for other kernel modules
dell-rbtn: Dell Airplane Mode Switch driver
samsung-laptop: Use acpi_video_unregister_backlight instead of acpi_video_unregister
asus-wmi: Use acpi_video_unregister_backlight instead of acpi_video_unregister
apple_gmux: Use acpi_video_unregister_backlight instead of acpi_video_unregister
pvpanic: handle missing _STA correctly
ideapad_laptop: Lenovo G50-30 fix rfkill reports wireless blocked
asus-wmi: add fan control
Documentation/ABI: Add file describing the sysfs entries for toshiba_haps
toshiba_haps: Make use of DEVICE_ATTR_{RW, WO} macros
toshiba_haps: Replace sscanf with kstrtoint
toshiba_acpi: Bump driver version to 0.22
toshiba_acpi: Remove TOS_FAILURE check from some functions
toshiba_acpi: Comments cleanup
toshiba_acpi: Rename hci_{read, write}1 functions
toshiba_acpi: Remove no longer needed hci_{read, write}2 functions
toshiba_bluetooth: Change BT status message to debug
...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
genalloc: rename of_get_named_gen_pool() to of_gen_pool_get()
genalloc: rename dev_get_gen_pool() to gen_pool_get()
x86: opt into HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit
MAINTAINERS: add zpool
MAINTAINERS: BCACHE: Kent Overstreet has changed email address
MAINTAINERS: move Jens Osterkamp to CREDITS
MAINTAINERS: remove unused nbd.h pattern
MAINTAINERS: update brcm gpio filename pattern
MAINTAINERS: update brcm dts pattern
MAINTAINERS: update sound soc intel patterns
MAINTAINERS: remove website for paride
MAINTAINERS: update Emulex ocrdma email addresses
bcache: use kvfree() in various places
libcxgbi: use kvfree() in cxgbi_free_big_mem()
target: use kvfree() in session alloc and free
IB/ehca: use kvfree() in ipz_queue_{cd}tor()
drm/nouveau/gem: use kvfree() in u_free()
drm: use kvfree() in drm_free_large()
cxgb4: use kvfree() in t4_free_mem()
cxgb3: use kvfree() in cxgb_free_mem()
...
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This contains:
- a build regression fix introduced by the timeconst move
- a hotplug regression fix introduced by the timer wheel diet
- a cpu hotplug bug fix for the exynos clocksource driver"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Remove development rules from Kbuild/Makefile
timer: Fix hotplug regression
clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
Pull crypto fixes from Herbert Xu:
"This fixes the aesni setkey error and removes a couple of unnecessary
NULL checks in the Intel qat driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni - fix failing setkey for rfc4106-gcm-aesni
crypto: qat - Deletion of unnecessary checks before two function calls
1) mlx4 driver bug fixes (TX queue wakeups, csum complete indications)
from Ido Shamay, Eran Ben Elisha, and Or Gerlitz.
2) Missing unlock in error path of PTP support in renesas driver, from
Dan Carpenter.
3) Add Vitesse 8641 phy IDs to vitesse PHY driver, from Shaohui Xie.
4) Bnx2x driver bug fixes (linearization of encap packets, scratchpad
parity error notifications, flow-control and speed settings) from
Yuval Mintz, Manish Chopra, Shahed Shaikh, and Ariel Elior.
5) ipv6 extension header parsing in the igb chip has a HW errata,
disable it. Frm Todd Fujinaka.
6) Fix PCI link state locking issue in e1000e driver, from Yanir
Lubetkin.
7) Cure panics during MTU change in i40e, from Mitch Williams.
8) Don't leak promisc refs in DSA slave driver, from Gilad Ben-Yossef.
9) Add missing HAS_DMA dep to VIA Rhine driver, from Geery
Uytterhoeven.
10) Make sure DMA map/unmap calls are symmetric in bnx2x driver, from
Michal Schmidt.
11) Workaround for MDIO access problems in bcm7xxx devices, from FLorian
Fainelli.
12) Fix races in SCTP protocol between OTTB responses and route
removals, from Alexander Sverdlin.
13) Fix jumbo frame checksum issue with some mvneta devices, from Simon
Guinot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (58 commits)
sock_diag: don't broadcast kernel sockets
net: mvneta: disable IP checksum with jumbo frames for Armada 370
ARM: mvebu: update Ethernet compatible string for Armada XP
net: mvneta: introduce compatible string "marvell, armada-xp-neta"
api: fix compatibility of linux/in.h with netinet/in.h
net: icplus: fix typo in constant name
sis900: Trivial: Fix typos in enums
stmmac: Trivial: fix typo in constant name
sctp: Fix race between OOTB responce and route removal
net-Liquidio: Delete unnecessary checks before the function call "vfree"
vmxnet3: Bump up driver version number
amd-xgbe: Add the __GFP_NOWARN flag to Rx buffer allocation
net: phy: mdio-bcm-unimac: workaround initial read failures for integrated PHYs
net: bcmgenet: workaround initial read failures for integrated PHYs
net: phy: bcm7xxx: workaround MDIO management controller initial read
bnx2x: fix DMA API usage
net: via: VIA_RHINE and VIA_VELOCITY should depend on HAS_DMA
net/phy: tune get_phy_c45_ids to support more c45 phy
bnx2x: fix lockdep splat
net: fec: don't access RACC register when not available
...
Merge tag 'iommu-fixes-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pul IOMMU fixes from Joerg Roedel:
"Four fixes have queued up to fix regressions introduced after v4.1:
- Don't fail IOMMU driver initialization when the add_device
call-back returns -ENODEV, as that just means that the device is
not translated by the IOMMU. This is pretty common on ARM.
- Two fixes for the ARM-SMMU driver for a wrong feature check and to
remove a redundant NULL check.
- A fix for the AMD IOMMU driver to fix a boot panic on systems where
the BIOS requests Unity Mappings in the IVRS table"
* tag 'iommu-fixes-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Introduce protection_domain_init() function
iommu/arm-smmu: Delete an unnecessary check before the function call "free_io_pgtable_ops"
iommu/arm-smmu: Fix broken ATOS check
iommu: Ignore -ENODEV errors from add_device call-back
Merge tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a bunch of small fixes, mostly for HD-audio quirks, in
addition to a few regression fixes and trivial cleanups"
* tag 'sound-fix-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: Fix uninintialized error return
ALSA: hda: Delete an unnecessary check before the function call "snd_info_free_entry"
ALSA: hda - Add a fixup for Dell E7450
ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780
ALSA: hda - Add headset support to Acer Aspire V5
ALSA: hda - restore the MIC FIXUP for some Dell machines
ALSA: jack: Fix endless loop at unique index detection
ALSA: hda - set proper caps for newer AMD hda audio in KB/KV
ALSA: hda - Disable widget power-save for VIA codecs
ALSA: hda - Fix Dock Headphone on Thinkpad X250 seen as a Line Out
WARNING: mm/built-in.o(.text.unlikely+0xc22): Section mismatch in reference from the function .new_kmalloc_cache() to the variable .init.rodata:kmalloc_info
The function .new_kmalloc_cache() references
the variable __initconst kmalloc_info.
Signed-off-by: Christoph Lameter <cl@linux.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://github.com/acpica/acpica/commit/1a8ec7b8 Signed-off-by: gongzg <gongzhaogang@inspur.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Add constans for the start_method.
- Remove the control structure, not part of ACPI, not defined in the current
TCG spec.
Link: https://github.com/acpica/acpica/commit/254bf77e Reported-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes for a new version of the 3rd party spec for these tables,
the "TCG ACPI Specification", December 14, 2014. Also, moved the
definition of TPM2 to actbl2.h, next to TCPA, since both should
be together.
Update the table compiler/disassembler code for the tables.
However, the "Server" TCPA table is not supported at this time.
Link: https://github.com/acpica/acpica/commit/33140b44 Reported-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://github.com/acpica/acpica/commit/f51bf849 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Across all of ACPICA. Replace C library macros such as ACPI_STRLEN with the
standard names such as strlen. The original purpose for these macros is
long since obsolete.
Also cast various invocations as necessary. Bob Moore, Jung-uk Kim, Lv Zheng.
In order to work without any additional option to dump tables when /dev/mem
doesn't exist, this patch switches the default behavior of acpidump to dump
from /sys/firmware/acpi/tables. Reported by Al Stone, Fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/04c3bd7e Reported-by: Al Stone <ahs3@redhat.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The /dev/mem can be configured out, in which case, acpidump should still
work with "-c" option as tables can be found in /sys/firmware/acpi/tables.
This patch allows acpidump to work without /dev/mem.
This patch has been tested with "acpidump -c" and "acpidump -c -n FADT".
And it worked as expected. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/ab29013c Reported-by: Al Stone <ahs3@redhat.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Especially for use of the Index operator. For buffers and strings,
only output the actual byte pointed to by the index. For packages,
only print the package element decoded by the index.
Link: https://github.com/acpica/acpica/commit/d4a53a39 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://github.com/acpica/acpica/commit/3f78b7fb Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no reference counting implemented for struct acpi_namespace_node, so it
is currently not removable during runtime.
This patch changes the namespace override code to keep the old
struct acpi_namespace_node undeleted so that the override mechanism can happen
during runtime. Bob Moore.
Link: https://github.com/acpica/acpica/commit/c0ce529e Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds OSDT (Override System Definition Table) support.
When OSDT is loaded, conflict namespace objects will be overridden
by the AML interpreter. Bob Moore, Lv Zheng.
Link: https://github.com/acpica/acpica/commit/27415c82 Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds an "NamespaceOverride" flag in struct acpi_walk_state, and allows
namespace objects to be overridden when this flag is set. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/6084e34e Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support for the new version field in the generic distributor
subtable. Hanjun Guo <hanjun.guo@linaro.org>
Link: https://github.com/acpica/acpica/commit/4b100dc4 Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI Device object often contains a _CLS object to supply PCI-defined class
code for the device. This patch introduces logic to process the _CLS
object. Suravee Suthikulpanit, Lv Zheng.
Link: https://github.com/acpica/acpica/commit/9a2b638a Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org> Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch copies EFI interface definitions to the ACPICA code base so that
the EFI utility support can be ported to other EFI implementation.
Known issues:
1. MS Builds of uefi_call_wrapper()
The uefi_call_wrapper() in GNU EFI is implemented in a the way to work
around the ABI difference between Unix and MS. While I don't have
environment to test the MS builds.
In order to port the ACPICA utilities to other EFI implementation, all that
need to be done is to impelement the 64-bit division support and the
program entry point where the efi_main() is invoked. Code to impelement
these is platform specific, and ACPICA currently choose to hide such
platform specific code within the specific EFI impelementation. Lv Zheng.
This patch doesn't affect Linux kernel.
Link: https://github.com/acpica/acpica/commit/5d00e67a Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch intoduces generic variable macro detection support and fixes
build breakage issue with macros using __VA_ARGS__ feature defined in
C99.
This patch fixes this build issue. Lv Zheng.
This patch doesn't affect Linux kernel.
Link: https://github.com/acpica/acpica/commit/72f5a358 Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following commit temporarily disables correct 64-bit FADT addresses
favor during the period the root cause of the bug is not fixed:
Commit: ddf899af51b57732aeb49d49d09eff5feb219d20
ACPICA: Tables: Restore old behavor to favor 32-bit FADT addresses.
With enough protections, this patch re-enables 64-bit FADT addresses by
default. If regressions are reported against such change, this patch should
be bisected and reverted.
Note that 64-bit FACS favor and 64-bit firmware waking vector favor are
excluded by this commit in order not to break OSPMs. Lv Zheng.
This patch adds a new FACS initialization flag for acpi_tb_initialize().
acpi_enable_subsystem() might be invoked several times in OS bootup process,
and we don't want FACS initialization to be invoked twice. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/90f5332a Cc: All applicable <stable@vger.kernel.org> # All applicable Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following commit is reported to have broken s2ram on some platforms:
Commit: 1b95f3b328e44ebc2e50d7edb7c1b01397245f57
ACPICA: Add option to favor 32-bit FADT addresses.
The platform reports 2 FACS tables (which is not allowed by ACPI
specification) and the new 32-bit address favor rule forces OSPMs to use
the FACS table reported via FADT's X_FIRMWARE_CTRL field.
The root cause of the reported bug might be one of the followings:
1. BIOS may favor the 64-bit firmware waking vector address when the
version of the FACS is greater than 0 and Linux currently only supports
resuming from the real mode, so the 64-bit firmware waking vector has
never been set and might be invalid to BIOS while the commit enables
higher version FACS.
2. BIOS may favor the FACS reported via the "FIRMWARE_CTRL" field in the
FADT while the commit doesn't set the firmware waking vector address of
the FACS reported by "FIRMWARE_CTRL", it only sets the firware waking
vector address of the FACS reported by "X_FIRMWARE_CTRL".
This patch excludes the cases that can trigger the bugs caused by the root
cause 2.
There is no handshaking mechanism can be used by OSPM to tell BIOS which
FACS is currently used. Thus the FACS reported by "FIRMWARE_CTRL" may still
be used by BIOS and the 0 value of the 32-bit firmware waking vector might
trigger such failure.
This patch enables the firmware waking vectors for both 32bit/64bit FACS
tables in order to ensure we can exclude the cases that trigger the bugs
caused by the root cause 2. The exclusion is split into 2 commits so that
if it turns out not to be necessary, this single commit can be reverted
without affecting the useful one. Lv Zheng, Bob Moore.
The following commit is reported to have broken s2ram on some platforms:
Commit: 1b95f3b328e44ebc2e50d7edb7c1b01397245f57
ACPICA: Add option to favor 32-bit FADT addresses.
The platform reports 2 FACS tables (which is not allowed by ACPI
specification) and the new 32-bit address favor rule forces OSPMs to use
the FACS table reported via FADT's X_FIRMWARE_CTRL field.
The root cause of the reported bug might be one of the followings:
1. BIOS may favor the 64-bit firmware waking vector address when the
version of the FACS is greater than 0 and Linux currently only supports
resuming from the real mode, so the 64-bit firmware waking vector has
never been set and might be invalid to BIOS while the commit enables
higher version FACS.
2. BIOS may favor the FACS reported via the "FIRMWARE_CTRL" field in the
FADT while the commit doesn't set the firmware waking vector address of
the FACS reported by "FIRMWARE_CTRL", it only sets the firware waking
vector address of the FACS reported by "X_FIRMWARE_CTRL".
This patch excludes the cases that can trigger the bugs caused by the root
cause 2.
There is no handshaking mechanism can be used by OSPM to tell BIOS which
FACS is currently used. Thus the FACS reported by "FIRMWARE_CTRL" may still
be used by BIOS and the 0 value of the 32-bit firmware waking vector might
trigger such failure.
This patch tries to favor 32bit FACS address in another way where both the
FACS reported by "FIRMWARE_CTRL" and the FACS reported by "X_FIRMWARE_CTRL"
are loaded so that further commit can set firmware waking vector in the
both tables to ensure we can exclude the cases that trigger the bugs caused
by the root cause 2. The exclusion is split into 2 commits as this commit
is also useful for dumping more ACPI tables, it won't get reverted when
such exclusion is no longer necessary. Lv Zheng.
The following commit is reported to have broken s2ram on some platforms:
Commit: 1b95f3b328e44ebc2e50d7edb7c1b01397245f57
ACPICA: Add option to favor 32-bit FADT addresses.
The platform reports 2 FACS tables (which is not allowed by ACPI
specification) and the new 32-bit address favor rule forces OSPMs to use
the FACS table reported via FADT's X_FIRMWARE_CTRL field.
The root cause of the reported bug might be one of the followings:
1. BIOS may favor the 64-bit firmware waking vector address when the
version of the FACS is greater than 0 and Linux currently only supports
resuming from the real mode, so the 64-bit firmware waking vector has
never been set and might be invalid to BIOS while the commit enables
higher version FACS.
2. BIOS may favor the FACS reported via the "FIRMWARE_CTRL" field in the
FADT while the commit doesn't set the firmware waking vector address of
the FACS reported by "FIRMWARE_CTRL", it only sets the firware waking
vector address of the FACS reported by "X_FIRMWARE_CTRL".
This patch excludes the cases that can trigger the bugs caused by the root
cause 1.
ACPI specification says:
A. 32-bit FACS address (FIRMWARE_CTRL field in FADT):
Physical memory address of the FACS, where OSPM and firmware exchange
control information.
If the X_FIRMWARE_CTRL field contains a non zero value then this field
must be zero.
A zero value indicates that no FACS is specified by this field.
B. 64-bit FACS address (X_FIRMWARE_CTRL field in FADT):
64bit physical memory address of the FACS.
This field is used when the physical address of the FACS is above 4GB.
If the FIRMWARE_CTRL field contains a non zero value then this field
must be zero.
A zero value indicates that no FACS is specified by this field.
Thus the 32bit and 64bit firmware waking vector should indicate completely
different resuming environment - real mode (1MB addressable) and non real
mode (4GB+ addressable) and currently Linux only supports resuming from
real mode.
This patch enables 64-bit firmware waking vector for selected FACS via new
acpi_set_firmware_waking_vectors() API so that it's up to OSPMs to
determine which resuming mode should be used by BIOS and ACPICA changes
won't trigger the bugs caused by the root cause 1. Lv Zheng.
Merge tag 'pm+acpi-4.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes that didn't make it to the previous PM+ACPI pull
request or are fixing issues introduced by it.
Specifics:
- Fix a recently added memory leak in an error path in the ACPI
resources management code (Dan Carpenter)
- Fix a build warning triggered by an ACPI video header function that
should be static inline (Borislav Petkov)
- Change names of helper function converting struct fwnode_handle
pointers to either struct device_node or struct acpi_device
pointers so they don't conflict with local variable names
(Alexander Sverdlin)
- Make the hibernate core re-enable nonboot CPUs on failures to
disable them as expected (Vitaly Kuznetsov)
- Increase the default timeout of the device suspend watchdog to
prevent it from triggering too early on some systems (Takashi Iwai)
- Prevent the cpuidle powernv driver from registering idle states
with CPUIDLE_FLAG_TIMER_STOP set if CONFIG_TICK_ONESHOT is unset
which leads to boot hangs (Preeti U Murthy)"
* tag 'pm+acpi-4.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
ACPI / video: Inline acpi_video_set_dmi_backlight_type
ACPI / resources: free memory on error in add_region_before()
Stevens, Nick [Wed, 1 Jul 2015 16:07:41 +0000 (16:07 +0000)]
hwmon: (mcp3021) Fix broken output scaling
The mcp3021 scaling code is dividing the VDD (full-scale) value in
millivolts by the A2D resolution to obtain the scaling factor. When VDD
is 3300mV (the standard value) and the resolution is 12-bit (4096
divisions), the result is a scale factor of 3300/4096, which is always
one. Effectively, the raw A2D reading is always being returned because
no scaling is applied.
This patch fixes the issue and simplifies the register-to-volts
calculation, removing the unneeded "output_scale" struct member.
Signed-off-by: Nick Stevens <Nick.Stevens@digi.com> Cc: stable@vger.kernel.org # v3.10+
[Guenter Roeck: Dropped unnecessary value check] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Florian Fainelli [Sat, 27 Jun 2015 16:25:43 +0000 (09:25 -0700)]
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
This reverts adefd60dadc7ffb7d53e6485f1ba45ddbf26cc71 ("ARM: BCM: Enable
NAND support for iProc SoCs") since it creates an unmet dependency for
MTD_NAND_BRCMNAND which depends on MTD and MTD_NAND, this results in the
following build failure for brcmnand:
LD init/built-in.o
drivers/built-in.o: In function `brcmnand_remove':
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:2234:
undefined reference to `nand_release'
drivers/built-in.o: In function `brcmnand_init_cs':
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:1933:
undefined reference to `nand_scan_ident'
/home/fainelli/dev/linux/drivers/mtd/nand/brcmnand/brcmnand.c:1958:
undefined reference to `nand_scan_tail'
Makefile:931: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
Instead, select this driver an all dependencies on the
multi_v7_defconfig.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
Kevin Hilman [Wed, 1 Jul 2015 20:01:03 +0000 (13:01 -0700)]
Merge tag 'mvebu-fixes-4.2-0' of git://git.infradead.org/linux-mvebu into next/late
Merge "ARM: mvebu: fixes for v4.2" from Gregory Clement:
mvebu fixes for 4.2 (part 0)
Fix legacy dove IRQ numbers
* tag 'mvebu-fixes-4.2-0' of git://git.infradead.org/linux-mvebu:
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
Kevin Hilman [Wed, 1 Jul 2015 19:53:49 +0000 (12:53 -0700)]
Merge tag 'mvebu-dt-4.2-3' of git://git.infradead.org/linux-mvebu into next/late
Merge "ARM: mvebu: dt changes for v4.2" from Gregory Clement
mvebu dt changes for v4.2 (part #3)
Update Armada XP DT spi muxing after pinctrl function rename which was
merged in the pinctrl subsystem for 4.2. Without it the spi muxing
will be broken in 4.2-rc1 for Armada XP.
* tag 'mvebu-dt-4.2-3' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
Boris Brezillon [Wed, 17 Jun 2015 08:59:05 +0000 (10:59 +0200)]
ARM: at91/dt: update udc compatible strings
at91sam9g45, at91sam9x5 and sama5 SoCs should not use
"atmel,at91sam9rl-udc" for their USB device compatible property since
this compatible is attached to a specific hardware bug fix.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Bo Shen <voice.shen@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: <stable@vger.kernel.org> #4.0+ Signed-off-by: Kevin Hilman <khilman@linaro.org>
Kevin Hilman [Wed, 1 Jul 2015 19:25:13 +0000 (12:25 -0700)]
Merge tag 'omap-for-v4.2/wakeirq-drivers-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/late
Merge "omap generic wakeirq for v4.2 merge window" from Tony Lindgren:
Omap driver changes for v4.2 to switch drivers over to Linux generic
wake IRQ events for omap_hsmmc, 8250_omap and omap-serial
drivers.
The generic wake IRQs also fix issues that these drivers potentially
have with IRQ re-entrancy at least for serial-omap.
Note that because of dependencies and merge conflicts these are
based on Rafael's pm-wakeirq and Greg's tty-next branches.
* tag 'omap-for-v4.2/wakeirq-drivers-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (148 commits)
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
serial: sirf: fix system hung on console log output
serial: 8250: remove return statements from void function
sc16is7xx: use kworker for RS-485 configuration
sc16is7xx: use kworker to update ier bits
sc16is7xx: use kworker for md_proc
sc16is7xx: move RTS delay to workqueue
sc16is7xx: use kthread_worker for tx_work and irq
sc16is7xx: use LSR_TEMT_BIT in .tx_empty()
...
Stephen Boyd [Tue, 2 Jun 2015 19:12:58 +0000 (12:12 -0700)]
soc: qcom: spm: Fix idle on THUMB2 kernels
The ifc6410 firmware always enters the kernel in ARM state from
deep idle. Use the cpu_resume_arm() wrapper instead of
cpu_resume() to property switch into the THUMB2 state when we
wake up from idle.
This fixes a problem reported by Kevin Hilman on next-20150601
where the ifc6410 fails to boot a THUMB2 kernel because the
platform's firmware always enters the kernel in ARM mode from
deep idle states.
Reported-by: Kevin Hilman <khilman@linaro.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Lina Iyer <lina.iyer@linaro.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Kevin Hilman <khilman@linaro.org>
Merge tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Xen features and cleanups for 4.2-rc0:
- add "make xenconfig" to assist in generating configs for Xen guests
- preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests
- automatically use hvc0 as the default console in ARM guests"
* tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
block/xen-blkback: s/nr_pages/nr_segs/
block/xen-blkfront: Remove invalid comment
block/xen-blkfront: Remove unused macro MAXIMUM_OUTSTANDING_BLOCK_REQS
arm/xen: Drop duplicate define mfn_to_virt
xen/grant-table: Remove unused macro SPP
xen/xenbus: client: Fix call of virt_to_mfn in xenbus_grant_ring
xen: Include xen/page.h rather than asm/xen/page.h
kconfig: add xenconfig defconfig helper
kconfig: clarify kvmconfig is for kvm
xen/pcifront: Remove usage of struct timeval
xen/tmem: use BUILD_BUG_ON() in favor of BUG_ON()
hvc_xen: avoid uninitialized variable warning
xenbus: avoid uninitialized variable warning
xen/arm: allow console=hvc0 to be omitted for guests
arm,arm64/xen: move Xen initialization earlier
arm/xen: Correctly check if the event channel interrupt is present
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Merge tag 'arc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC architecture updates from Vineet Gupta:
- support for HS38 cores based on ARCv2 ISA
ARCv2 is the next generation ISA from Synopsys and basis for the
HS3{4,6,8} families of processors which retain the traditional ARC mantra of
low power and configurability and are now more performant and feature rich.
HS38x is a 10 stage pipeline core which supports MMU (with huge pages) and
SMP (upto 4 cores) among other features.
- support for ARC SDP (Software Development platform): Main Board + CPU Cards
= AXS101: CPU Card with ARC700 in silicon @ 700 MHz
= AXS103: CPU Card with HS38x in FPGA
- refactoring of ARCompact port to accomodate new ARCv2 ISA
- misc updates/cleanups
* tag 'arc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (72 commits)
ARC: Fix build failures for ARCompact in linux-next after ARCv2 support
ARCv2: Allow older gcc to cope with new regime of ARCv2/ARCompact support
ARCv2: [vdk] dts files and defconfig for HS38 VDK
ARCv2: [axs103] Support ARC SDP FPGA platform for HS38x cores
ARC: [axs101] Prepare for AXS103
ARCv2: [nsim*hs*] Support simulation platforms for HS38x cores
ARCv2: All bits in place, allow ARCv2 builds
ARCv2: SLC: Handle explcit flush for DMA ops (w/o IO-coherency)
ARCv2: STAR 9000837815 workaround hardware exclusive transactions livelock
ARC: Reduce bitops lines of code using macros
ARCv2: barriers
arch: conditionally define smp_{mb,rmb,wmb}
ARC: add smp barriers around atomics per Documentation/atomic_ops.txt
ARC: add compiler barrier to LLSC based cmpxchg
ARCv2: SMP: intc: IDU 2nd level intc for dynamic IRQ distribution
ARCv2: SMP: clocksource: Enable Global Real Time counter
ARCv2: SMP: ARConnect debug/robustness
ARCv2: SMP: Support ARConnect (MCIP) for Inter-Core-Interrupts et al
ARC: make plat_smp_ops weak to allow over-rides
ARCv2: clocksource: Introduce 64bit local RTC counter
...
vfs: Remove incorrect debugging WARN in prepend_path
The warning message in prepend_path is unclear and outdated. It was
added as a warning that the mechanism for generating names of pseudo
files had been removed from prepend_path and d_dname should be used
instead. Unfortunately the warning reads like a general warning,
making it unclear what to do with it.
Remove the warning. The transition it was added to warn about is long
over, and I added code several years ago which in rare cases causes
the warning to fire on legitimate code, and the warning is now firing
and scaring people for no good reason.
Cc: stable@vger.kernel.org Reported-by: Ivan Delalande <colona@arista.com> Reported-by: Omar Sandoval <osandov@osandov.com> Fixes: d59f45ba2bfdd ("vfs: In d_path don't call d_dname on a mount point") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
mnt: Update fs_fully_visible to test for permanently empty directories
fs_fully_visible attempts to make fresh mounts of proc and sysfs give
the mounter no more access to proc and sysfs than if they could have
by creating a bind mount. One aspect of proc and sysfs that makes
this particularly tricky is that there are other filesystems that
typically mount on top of proc and sysfs. As those filesystems are
mounted on empty directories in practice it is safe to ignore them.
However testing to ensure filesystems are mounted on empty directories
has not been something the in kernel data structures have supported so
the current test for an empty directory which checks to see
if nlink <= 2 is a bit lacking.
proc and sysfs have recently been modified to use the new empty_dir
infrastructure to create all of their dedicated mount points. Instead
of testing for S_ISDIR(inode->i_mode) && i_nlink <= 2 to see if a
directory is empty, test for is_empty_dir_inode(inode). That small
change guaranteess mounts found on proc and sysfs really are safe to
ignore, because the directories are not only empty but nothing can
ever be added to them. This guarantees there is nothing to worry
about when mounting proc and sysfs.
Cc: stable@vger.kernel.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
projects / kernel.git / log