Merge tag 'at91-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes #1 for 5.15:
- Fixes for newly introduced SAMA7G5 and its Power Management code.
Associated core peripherals need to be instantiated in DT for
benefiting from best PM support like Backup mode with DDR in
Self-Refresh.
- Add chip ID for SAMA7G5 for easing the kernel log identification.
- Avoid Camera Sensor probe error on sama5d27 som1 ek board.
* tag 'at91-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2_som1_ek: disable ISC node by default
ARM: at91: pm: switch backup area to vbat in backup mode
ARM: dts: at91: sama7g5: add chipid
ARM: dts: at91: sama7g5: add shdwc node
ARM: dts: at91: sama7g5: add securam node
ARM: dts: at91: sama7g5: add ram controllers
ARM: at91: pm: do not panic if ram controllers are not enabled
Eugen Hristev [Thu, 2 Sep 2021 12:13:58 +0000 (15:13 +0300)]
ARM: dts: at91: sama5d2_som1_ek: disable ISC node by default
Without a sensor node, the ISC will simply fail to probe, as the
corresponding port node is missing.
It is then logical to disable the node in the devicetree.
If we add a port with a connection to a sensor endpoint, ISC can be enabled.
Claudiu Beznea [Mon, 30 Aug 2021 10:09:27 +0000 (13:09 +0300)]
ARM: at91: pm: switch backup area to vbat in backup mode
Backup area is now switched to VDDIN33 at boot (with the help of
bootloader). When switching to backup mode we need to switch backup area
to VBAT as all the other power sources are cut off. The resuming from
backup mode is done with the help of bootloader, so there is no need to
do something particular in Linux to restore backup area power source.
Claudiu Beznea [Mon, 23 Aug 2021 13:19:12 +0000 (16:19 +0300)]
ARM: at91: pm: do not panic if ram controllers are not enabled
In case PM is enabled but there is no RAM controller information
in DT the code will panic. Avoid such scenarios by not initializing
platform specific PM code in case RAM controller is not provided
via DT.
Joel Stanley [Tue, 15 Jun 2021 01:14:34 +0000 (10:44 +0930)]
ARM: config: mutli v7: Reenable FB dependency
DRM_FBDEV_EMULATION previously selected FB and was default y as long as DRM
was enabled. In commit 6b2c04b84121 ("drm: Avoid circular dependencies for
CONFIG_FB") the select was replaced with a depends on FB, disabling the
drivers that depended on it.
Renable FB so we get back FB_EFI, FB_WM8505, FB_SH_MOBILE_LCDC, FB_SIMPLE and
VIDEO_VIVID.
It must be set to y and not a module as the test driver VIDEO_VIVID
requires it to be built in.
Joel Stanley [Tue, 15 Jun 2021 01:14:33 +0000 (10:44 +0930)]
ARM: config: multi v7: Enable dependancies
Some drivers have not been built as they gained dependencies in kconfig but those
dependencies were not added to the defconfig.
The MSM pinctrl drivers fell out of the defconfig as of commit c0df5be3d139
("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then a
selected config"). Add PINCTRL_MSM so these stay enabled.
EDAC depends on RAS, so enable it to ensure the EDAC drivers stay
enabled.
Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Add missing fields and remove some duplicate fields when printing a
perf_event_attr.
- Fix hybrid config terms list corruption.
- Update kernel header copies, some resulted in new kernel features
being automagically added to 'perf trace' syscall/tracepoint argument
id->string translators.
- Add a file generated during the documentation build to .gitignore.
- Add an option to build without libbfd, as some distros, like Debian
consider its ABI unstable.
- Add support to print a textual representation of IBS raw sample data
in 'perf report'.
- Fix bpf 'perf test' sample mismatch reporting
- Fix passing arguments to stackcollapse report in a 'perf script'
python script.
- Allow build-id with trailing zeros.
- Look for ImageBase in PE file to compute .text offset.
* tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (25 commits)
tools headers UAPI: Update tools's copy of drm.h headers
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/fs.h with the kernel sources
tools headers UAPI: Sync linux/in.h copy with the kernel sources
perf tools: Add an option to build without libbfd
perf tools: Allow build-id with trailing zeros
perf tools: Fix hybrid config terms list corruption
perf tools: Factor out copy_config_terms() and free_config_terms()
perf tools: Fix perf_event_attr__fprintf() missing/dupl. fields
perf tools: Ignore Documentation dependency file
perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
tools include UAPI: Update linux/mount.h copy
perf beauty: Cover more flags in the move_mount syscall argument beautifier
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
perf report: Add support to print a textual representation of IBS raw sample data
perf report: Add tools/arch/x86/include/asm/amd-ibs.h
perf env: Add perf_env__cpuid, perf_env__{nr_}pmu_mappings
...
* tag 'compiler-attributes-for-linus-v5.15-rc1-v2' of git://github.com/ojeda/linux:
compiler_attributes.h: move __compiletime_{error|warning}
MAINTAINERS: add Nick as Reviewer for compiler_attributes.h
Compiler Attributes: fix __has_attribute(__no_sanitize_coverage__) for GCC 4
Merge tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux
Pull auxdisplay updates from Miguel Ojeda:
"An assortment of improvements for auxdisplay:
- Replace symbolic permissions with octal permissions (Jinchao Wang)
- ks0108: Switch to use module_parport_driver() (Andy Shevchenko)
- charlcd: Drop unneeded initializers and switch to C99 style (Andy
Shevchenko)
- hd44780: Fix oops on module unloading (Lars Poeschel)
- Add I2C gpio expander example (Ralf Schlatterbeck)"
* tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux:
auxdisplay: Replace symbolic permissions with octal permissions
auxdisplay: ks0108: Switch to use module_parport_driver()
auxdisplay: charlcd: Drop unneeded initializers and switch to C99 style
auxdisplay: hd44780: Fix oops on module unloading
auxdisplay: Add I2C gpio expander example
Merge tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
"Updates for the SMP and CPU hotplug:
- Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
original hotplug code and now causing trouble with the ARM64 cache
topology setup due to the pointless SMP function call.
It's not longer required as the hotplug callbacks are guaranteed to
be invoked on the upcoming CPU.
- Remove the deprecated and now unused CPU hotplug functions
- Rewrite the CPU hotplug API documentation"
* tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: core-api/cpuhotplug: Rewrite the API section
cpu/hotplug: Remove deprecated CPU-hotplug functions.
thermal: Replace deprecated CPU-hotplug functions.
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()
Merge tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver fix from Greg KH:
"Here is a single patch for 5.15-rc1, for the lkdtm misc driver.
It resolves a build issue that many people were hitting with your
current tree, and Kees and others felt would be good to get merged
before -rc1 comes out, to prevent them from having to constantly hit
it as many development trees restart on -rc1, not older -rc releases.
It has NOT been in linux-next, but has passed 0-day testing and looks
'obviously correct' when reviewing it locally :)"
* tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
lkdtm: Use init_uts_ns.name instead of macros
Merge tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Make sure the idle timer expires in hardirq context, on PREEMPT_RT
- Make sure the run-queue balance callback is invoked only on the
outgoing CPU
* tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Prevent balance_push() on remote runqueues
sched/idle: Make the idle timer expire in hard interrupt context
Merge tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
- Fix the futex PI requeue machinery to not return to userspace in
inconsistent state
- Avoid a potential null pointer dereference in the ww_mutex deadlock
check
- Other smaller cleanups and optimizations
* tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Fix ww_mutex deadlock check
futex: Remove unused variable 'vpid' in futex_proxy_trylock_atomic()
futex: Avoid redundant task lookup
futex: Clarify comment for requeue_pi_wake_futex()
futex: Prevent inconsistent state and exit race
futex: Return error code instead of assigning it without effect
locking/rwsem: Add missing __init_rwsem() for PREEMPT_RT
Merge tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Handle negative second values properly when converting a timespec64
to nanoseconds.
* tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Handle negative seconds correctly in timespec64_to_ns()
Merge branch 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull namei updates from Al Viro:
"Clearing fallout from mkdirat in io_uring series. The fix in the
kern_path_locked() patch plus associated cleanups"
* 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
putname(): IS_ERR_OR_NULL() is wrong here
namei: Standardize callers of filename_create()
namei: Standardize callers of filename_lookup()
rename __filename_parentat() to filename_parentat()
namei: Fix use after free in kern_path_locked
Merge tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smbfs updates from Steve French:
"cifs/smb3 updates:
- DFS reconnect fix
- begin creating common headers for server and client
- rename the cifs_common directory to smbfs_common to be more
consistent ie change use of the name cifs to smb (smb3 or smbfs is
more accurate, as the very old cifs dialect has long been
superseded by smb3 dialects).
In the future we can rename the fs/cifs directory to fs/smbfs.
This does not include the set of multichannel fixes nor the two
deferred close fixes (they are still being reviewed and tested)"
* tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: properly invalidate cached root handle when closing it
cifs: move SMB FSCTL definitions to common code
cifs: rename cifs_common to smbfs_common
cifs: update FSCTL definitions
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
Merge branch 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccinelle updates from Julia Lawall:
"These changes update some existing semantic patches with
respect to some recent changes in the kernel.
Specifically, the change to kvmalloc.cocci searches for
kfree_sensitive rather than kzfree, and the change to
use_after_iter.cocci adds list_entry_is_head as a valid
use of a list iterator index variable after the end of
the loop"
* 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccinelle: allow list_entry_is_head() to use pos
coccinelle: api: rename kzfree to kfree_sensitive
$ tools/perf/trace/beauty/drm_ioctl.sh > before
$ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
$ tools/perf/trace/beauty/drm_ioctl.sh > after
$ diff -u before after
Silencing these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h
Cc: Simon Ser <contact@emersion.fr> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
To pick the changes in:
223c591a27159e70 ("drm/i915/userptr: Probe existence of backing struct pages upon creation") d655c13d2e0f8536 ("drm/i915/guc: Implement GuC priority management") eae682475c458edb ("drm/i915/uapi: reject set_domain for discrete") ff59262818ba63a1 ("drm/i915: Add TTM offset argument to mmap.") f15469219992c64a ("drm/i915/uapi: convert drm_i915_gem_userptr to kernel doc") 9117fbe25883e94e ("drm/i915/uapi: reject caching ioctls for discrete") baee6516b577e32f ("drm/i915/uapi: convert drm_i915_gem_set_domain to kernel doc") 146ea55e6fa505b2 ("drm/i915/uapi: convert drm_i915_gem_caching to kernel doc") cf9b30e1ac204e7d ("drm/i915: Drop the CONTEXT_CLONE API (v2)") 4ff33858bfb8017c ("drm/i915: Drop I915_CONTEXT_PARAM_NO_ZEROMAP") a6d72a285d01f300 ("drm/i915: Drop I915_CONTEXT_PARAM_RINGSIZE") b786c99bdc0b02e9 ("drm/i915: Document the Virtual Engine uAPI") 38d90699a27b7663 ("drm/i915: Fix busy ioctl commentary")
That doesn't result in any changes to tooling as no new ioctl were
added (at least not perceived by tools/perf/trace/beauty/drm_ioctl.sh).
Addressing this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers UAPI: Sync linux/fs.h with the kernel sources
To pick the change in:
45ae0f9ae0a91cf9 ("block: add ioctl to read the disk sequence number")
It adds a new ioctl, but we are still not using that to generate tables
for 'perf trace', so no changes in tooling.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h
tools headers UAPI: Sync linux/in.h copy with the kernel sources
To pick the changes in:
404b1c2591eab4bc ("net/ipv4/ipv6: Replace one-element arraya with flexible-array members") 08c3107b60ba5f20 ("net/ipv4: Replace one-element array with flexible-array member")
That don't result in any change in tooling, the structs changed remains
with the same layout.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net> Cc: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: tony garnock-jones <tonyg@leastfixedpoint.com> Link: http://lore.kernel.org/lkml/20210910225756.729087-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Fri, 10 Sep 2021 22:46:30 +0000 (15:46 -0700)]
perf tools: Allow build-id with trailing zeros
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 6e55904be4ae43fd ("perf tools: Pass build_id object to dso__build_id_equal()") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Thu, 9 Sep 2021 12:55:08 +0000 (15:55 +0300)]
perf tools: Fix hybrid config terms list corruption
A config terms list was spliced twice, resulting in a never-ending loop
when the list was traversed. Fix by using list_splice_init() and copying
and freeing the lists as necessary.
This patch also depends on patch "perf tools: Factor out
copy_config_terms() and free_config_terms()"
Example on ADL:
Before:
# perf record -e '{intel_pt//,cycles/aux-sample-size=4096/pp}' uname &
# jobs
[1]+ Running perf record -e "{intel_pt//,cycles/aux-sample-size=4096/pp}" uname
# perf top -E 10
PerfTop: 4071 irqs/sec kernel: 6.9% exact: 100.0% lost: 0/0 drop: 0/0 [4000Hz cycles], (all, 24 CPUs)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Adrian Hunter [Thu, 9 Sep 2021 12:55:07 +0000 (15:55 +0300)]
perf tools: Factor out copy_config_terms() and free_config_terms()
Factor out copy_config_terms() and free_config_terms() so that they can
be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Kan Liang <kan.liang@linux.intel.com>
Link: https //lore.kernel.org/r/20210909125508.28693-2-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge tag 'io_uring-5.15-2021-09-11' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Fix an off-by-one in a BUILD_BUG_ON() check. Not a real issue right
now as we have plenty of flags left, but could become one. (Hao)
- Fix lockdep issue introduced in this merge window (me)
- Fix a few issues with the worker creation (me, Pavel, Qiang)
- Fix regression with wq_has_sleeper() for IOPOLL (Pavel)
- Timeout link error propagation fix (Pavel)
* tag 'io_uring-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
io_uring: fix off-by-one in BUILD_BUG_ON check of __REQ_F_LAST_BIT
io_uring: fail links of cancelled timeouts
io-wq: fix memory leak in create_io_worker()
io-wq: fix silly logic error in io_task_work_match()
io_uring: drop ctx->uring_lock before acquiring sqd->lock
io_uring: fix missing mb() before waitqueue_active
io-wq: fix cancellation on create-worker failure
Merge tag 'block-5.15-2021-09-11' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph:
- fix nvmet command set reporting for passthrough controllers (Adam Manzanares)
- update a MAINTAINERS email address (Chaitanya Kulkarni)
- set QUEUE_FLAG_NOWAIT for nvme-multipth (me)
- handle errors from add_disk() (Luis Chamberlain)
- update the keep alive interval when kato is modified (Tatsuya Sasaki)
- fix a buffer overrun in nvmet_subsys_attr_serial (Hannes Reinecke)
- do not reset transport on data digest errors in nvme-tcp (Daniel Wagner)
- only call synchronize_srcu when clearing current path (Daniel Wagner)
- revalidate paths during rescan (Hannes Reinecke)
- Split out the fs/block_dev into block/fops.c and block/bdev.c, which
has been long overdue. Do this now before -rc1, to avoid annoying
conflicts due to this (Christoph)
* tag 'block-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
n64cart: fix return value check in n64cart_probe()
blk-mq: allow 4x BLK_MAX_REQUEST_COUNT at blk_plug for multiple_queues
block: move fs/block_dev.c to block/bdev.c
block: split out operations on block special files
blk-throttle: fix UAF by deleteing timer in blk_throtl_exit()
block: genhd: don't call blkdev_show() with major_names_lock held
nvme: update MAINTAINERS email address
nvme: add error handling support for add_disk()
nvme: only call synchronize_srcu when clearing current path
nvme: update keep alive interval when kato is modified
nvme-tcp: Do not reset transport on data digest errors
nvmet: fixup buffer overrun in nvmet_subsys_attr_serial()
nvmet: return bool from nvmet_passthru_ctrl and nvmet_is_passthru_req
nvmet: looks at the passthrough controller when initializing CAP
nvme: move nvme_multi_css into nvme.h
nvme-multipath: revalidate paths during rescan
nvme-multipath: set QUEUE_FLAG_NOWAIT
Merge tag 'libata-5.15-2021-09-11' of git://git.kernel.dk/linux-block
Pull libata maintainer update from Jens Axboe:
"Damien agreed to take over maintainership of libata, and he would be a
great candidate for it. Update the MAINTAINERS entry to reflect the
change in maintainer and git tree"
* tag 'libata-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
libata: pass over maintainership to Damien Le Moal
Merge tag 'trace-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Minor fixes to the processing of the bootconfig tree"
* tag 'trace-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Rename xbc_node_find_child() to xbc_node_find_subkey()
tracing/boot: Fix to check the histogram control param is a leaf node
tracing/boot: Fix trace_boot_hist_add_array() to check array is value
Merge tag 'devicetree-fixes-for-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Disable fw_devlinks on x86 DT platforms to fix OLPC
- More replacing oneOf+const with enum on a few new schemas
- Drop unnecessary type references on Xilinx SPI binding schema
* tag 'devicetree-fixes-for-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
spi: dt-bindings: xilinx: Drop type reference on *-bits properties
dt-bindings: More use 'enum' instead of 'oneOf' plus 'const' entries
of: property: Disable fw_devlink DT support for X86
Merge tag 'rtc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The broken down time conversion is similar to what is done in the time
subsystem since v5.14. The rest is fairly straightforward.
Subsystem:
- Switch to Neri and Schneider time conversion algorithm
Drivers:
- rx8025: add rx8035 support
- s5m: modernize driver and set range"
* tag 'rtc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: rx8010: select REGMAP_I2C
dt-bindings: rtc: add Epson RX-8025 and RX-8035
rtc: rx8025: implement RX-8035 support
rtc: cmos: remove stale REVISIT comments
rtc: tps65910: Correct driver module alias
rtc: move RTC_LIB_KUNIT_TEST to proper location
rtc: lib_test: add MODULE_LICENSE
rtc: Improve performance of rtc_time64_to_tm(). Add tests.
rtc: s5m: set range
rtc: s5m: enable wakeup only when available
rtc: s5m: signal the core when alarm are not available
rtc: s5m: switch to devm_rtc_allocate_device
Merge tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire updates from Stefan Richter:
- Migrate the bus snooper driver 'nosy' from PCI to DMA API
- Small janitorial cleanup in the IPv4/v6-over-1394 driver
[ The 'nosy' change already come in as a different commit through Greg
KH in the misc tree back in the previous merge window, so only the
cleanup ends up being new to 5.15 - Linus ]
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: nosy: switch from 'pci_' to 'dma_' API
firewire: net: remove unused variable 'guid'
Merge tag 'pwm/for-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes this time around are mostly janitorial in nature. A lot of
this is simplifications of drivers using device-managed functions and
improving compilation coverage.
The Mediatek display PWM driver now supports the atomic API.
Cleanups and minor fixes make up the remainder of this set"
* tag 'pwm/for-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (54 commits)
pwm: mtk-disp: Implement atomic API .get_state()
pwm: mtk-disp: Fix overflow in period and duty calculation
pwm: mtk-disp: Implement atomic API .apply()
pwm: mtk-disp: Adjust the clocks to avoid them mismatch
dt-bindings: pwm: rockchip: Add description for rk3568
pwm: Make pwmchip_remove() return void
pwm: sun4i: Don't check the return code of pwmchip_remove()
pwm: sifive: Don't check the return code of pwmchip_remove()
pwm: samsung: Don't check the return code of pwmchip_remove()
pwm: renesas-tpu: Don't check the return code of pwmchip_remove()
pwm: rcar: Don't check the return code of pwmchip_remove()
pwm: pca9685: Don't check the return code of pwmchip_remove()
pwm: omap-dmtimer: Don't check the return code of pwmchip_remove()
pwm: mtk-disp: Don't check the return code of pwmchip_remove()
pwm: imx-tpm: Don't check the return code of pwmchip_remove()
pwm: img: Don't check the return code of pwmchip_remove()
pwm: cros-ec: Don't check the return code of pwmchip_remove()
pwm: brcmstb: Don't check the return code of pwmchip_remove()
pwm: atmel-tcb: Don't check the return code of pwmchip_remove()
pwm: atmel-hlcdc: Don't check the return code of pwmchip_remove()
...
Merge tag 'thermal-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add the tegra3 thermal sensor and fix the compilation testing on
tegra by adding a dependency on ARCH_TEGRA along with COMPILE_TEST
(Dmitry Osipenko)
- Fix the error code for the exynos when devm_get_clk() fails (Dan
Carpenter)
- Add the TCC cooling support for AlderLake platform (Sumeet Pawnikar)
- Add support for hardware trip points for the rcar gen3 thermal driver
and store TSC id as unsigned int (Niklas Söderlund)
- Replace the deprecated CPU-hotplug functions get_online_cpus() and
put_online_cpus (Sebastian Andrzej Siewior)
- Add the thermal tools directory in the MAINTAINERS file (Daniel
Lezcano)
- Fix the Makefile and the cross compilation flags for the userspace
'tmon' tool (Rolf Eike Beer)
- Allow to use the IMOK independently from the GDDV on Int340x (Sumeet
Pawnikar)
- Fix the stub thermal_cooling_device_register() function prototype
which does not match the real function (Arnd Bergmann)
- Make the thermal trip point optional in the DT bindings (Maxime
Ripard)
- Fix a typo in a comment in the core code (Geert Uytterhoeven)
- Reduce the verbosity of the trace in the SoC thermal tegra driver
(Dmitry Osipenko)
- Add the support for the LMh (Limit Management hardware) driver on the
QCom platforms (Thara Gopinath)
- Allow processing of HWP interrupt by adding a weak function in the
Intel driver (Srinivas Pandruvada)
- Prevent an abort of the sensor probe is a channel is not used
(Matthias Kaehlcke)
* tag 'thermal-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal/drivers/qcom/spmi-adc-tm5: Don't abort probing if a sensor is not used
thermal/drivers/intel: Allow processing of HWP interrupt
dt-bindings: thermal: Add dt binding for QCOM LMh
thermal/drivers/qcom: Add support for LMh driver
firmware: qcom_scm: Introduce SCM calls to access LMh
thermal/drivers/tegra-soctherm: Silence message about clamped temperature
thermal: Spelling s/scallbacks/callbacks/
dt-bindings: thermal: Make trips node optional
thermal/core: Fix thermal_cooling_device_register() prototype
thermal/drivers/int340x: Use IMOK independently
tools/thermal/tmon: Add cross compiling support
thermal/tools/tmon: Improve the Makefile
MAINTAINERS: Add missing userspace thermal tools to the thermal section
thermal/drivers/intel_powerclamp: Replace deprecated CPU-hotplug functions.
thermal/drivers/rcar_gen3_thermal: Store TSC id as unsigned int
thermal/drivers/rcar_gen3_thermal: Add support for hardware trip points
drivers/thermal/intel: Add TCC cooling support for AlderLake platform
thermal/drivers/exynos: Fix an error code in exynos_tmu_probe()
thermal/drivers/tegra: Correct compile-testing of drivers
thermal/drivers/tegra: Add driver for Tegra30 thermal sensor
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- several device tree bindings for input devices have been converted to
yaml
- dropped no longer used ixp4xx-beeper and CSR Prima2 PWRC drivers
- analog joystick has been converted to use ktime API and no longer
warn about low resolution timers
- a few driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: analog - always use ktime functions
Input: mms114 - support MMS134S
Input: elan_i2c - reduce the resume time for controller in Whitebox
Input: edt-ft5x06 - added case for EDT EP0110M09
Input: adc-keys - drop bogus __refdata annotation
Input: Fix spelling mistake in Kconfig "useable" -> "usable"
Input: Fix spelling mistake in Kconfig "Modul" -> "Module"
Input: remove dead CSR Prima2 PWRC driver
Input: adp5589-keys - use the right header
Input: adp5588-keys - use the right header
dt-bindings: input: tsc2005: Convert to YAML schema
Input: ep93xx_keypad - prepare clock before using it
dt-bindings: input: sun4i-lradc: Add wakeup-source
dt-bindings: input: Convert Regulator Haptic binding to a schema
dt-bindings: input: Convert Pixcir Touchscreen binding to a schema
dt-bindings: input: Convert ChipOne ICN8318 binding to a schema
Input: pm8941-pwrkey - fix comma vs semicolon issue
dt-bindings: power: reset: qcom-pon: Convert qcom PON binding to yaml
dt-bindings: input: pm8941-pwrkey: Convert pm8941 power key binding to yaml
dt-bindings: power: reset: Change 'additionalProperties' to true
...
riscv: dts: microchip: mpfs-icicle: Fix serial console
Currently, nothing is output on the serial console, unless
"console=ttyS0,115200n8" or "earlycon" are appended to the kernel
command line. Enable automatic console selection using
chosen/stdout-path by adding a proper alias, and configure the expected
serial rate.
While at it, add aliases for the other three serial ports, which are
provided on the same micro-USB connector as the first one.
riscv: move the (z)install rules to arch/riscv/Makefile
Currently, the (z)install targets in arch/riscv/Makefile descend into
arch/riscv/boot/Makefile to invoke the shell script, but there is no
good reason to do so.
arch/riscv/Makefile can run the shell script directly.
The EFI system partition uses the FAT file system. Many distributions add
an entry in /etc/fstab for the ESP. We must ensure that mounting does not
fail.
The default code page for FAT is 437 (cf. CONFIG_FAT_DEFAULT_CODEPAGE).
The default IO character set is "iso8859-1" (cf. CONFIG_NLS_ISO8859_1).
So let's enable NLS_CODEPAGE_437 and NLS_ISO8859_1 in defconfig.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
NVMe is a non-volatile storage media attached via PCIe.
As NVMe has much higher throughput than other block devices like
SATA it is a must have for RISC-V. Enable CONFIG_BLK_DEV_NVME.
The HiFive Unmatched is a board providing M.2 slots for NVMe drives.
Enable CONFIG_PCIE_FU740.
The functions get_online_cpus() and put_online_cpus() have been
deprecated during the CPU hotplug rework. They map directly to
cpus_read_lock() and cpus_read_unlock().
Replace deprecated CPU-hotplug functions with the official version.
The behavior remains unchanged.
Thomas Gleixner [Fri, 10 Sep 2021 22:38:47 +0000 (00:38 +0200)]
Merge branch 'linus' into smp/urgent
Ensure that all usage sites of get/put_online_cpus() except for the
struggler in drivers/thermal are gone. So the last user and the deprecated
inlines can be removed.
perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
The btf__get_from_id() function was deprecated in favour of
btf__load_from_kernel_by_id(), but it is still avaiable, so use it to
provide a weak function btf__load_from_kernel_by_id() for older libbpf
when building perf with LIBBPF_DYNAMIC=1, i.e. using the system's libbpf
package.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
cd878851c97abe61 ("move_mount: allow to add a mount into an existing group")
That ends up adding support for the new MOVE_MOUNT_SET_GROUP move_mount
flag.
$ tools/perf/trace/beauty/move_mount_flags.sh > before
$ cp include/uapi/linux/mount.h tools/include/uapi/linux/mount.h
$ tools/perf/trace/beauty/move_mount_flags.sh > after
$ diff -u before after
--- before 2021-09-10 12:28:43.865279808 -0300
+++ after 2021-09-10 12:28:50.183429184 -0300
@@ -5,4 +5,5 @@
[ilog2(0x00000010) + 1] = "T_SYMLINKS",
[ilog2(0x00000020) + 1] = "T_AUTOMOUNTS",
[ilog2(0x00000040) + 1] = "T_EMPTY_PATH",
+ [ilog2(0x00000100) + 1] = "SET_GROUP",
};
$
So now one can use it in --filter expressions for tracepoints.
This silences this perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/linux/mount.h' differs from latest version at 'include/uapi/linux/mount.h'
diff -u tools/include/uapi/linux/mount.h include/uapi/linux/mount.h
Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers UAPI: Sync linux/prctl.h with the kernel sources
To pick the changes in:
be4b925d276f552e ("arm64: mte: change ASYNC and SYNC TCF settings into bitfields") a9c8ffed4692c356 ("x86, prctl: Hook L1D flushing in via prctl")
That don't result in any changes in tooling:
$ tools/perf/trace/beauty/prctl_option.sh > before
$ cp include/uapi/linux/prctl.h tools/include/uapi/linux/prctl.h
$ tools/perf/trace/beauty/prctl_option.sh > after
$ diff -u before after
$
Just silences this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/prctl.h' differs from latest version at 'include/uapi/linux/prctl.h'
diff -u tools/include/uapi/linux/prctl.h include/uapi/linux/prctl.h
Cc: Balbir Singh <sblbir@amazon.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Peter Collingbourne <pcc@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Which entails no changes in the tooling side as it doesn't introduce new
ioctls.
To silence this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/sound/asound.h' differs from latest version at 'include/uapi/sound/asound.h'
diff -u tools/include/uapi/sound/asound.h include/uapi/sound/asound.h
Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers UAPI: Sync linux/kvm.h with the kernel sources
To pick the changes in:
63b308a93699da2e ("KVM: stats: Support linear and logarithmic histogram statistics") f0b3826473928974 ("KVM: arm64: Add ioctl to fetch/store tags in a guest") a8c815ae1ed1d975 ("KVM: arm64: Introduce MTE VM feature")
That just rebuilds perf, as these patches don't add any new KVM ioctl to
be harvested for the the 'perf trace' ioctl syscall argument
beautifiers.
This is also by now used by tools/testing/selftests/kvm/, so that will
pick the new KVM_STATS_TYPE_LINEAR_HIST and KVM_STATS_TYPE_LOG_HIST
defines.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
diff -u tools/include/uapi/linux/kvm.h include/uapi/linux/kvm.h
Cc: Jing Zhang <jingzhangos@google.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Steven Price <steven.price@arm.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
That just rebuilds kvm-stat.c on x86, no change in functionality.
This silences these perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/uapi/asm/kvm.h' differs from latest version at 'arch/x86/include/uapi/asm/kvm.h'
diff -u tools/arch/x86/include/uapi/asm/kvm.h arch/x86/include/uapi/asm/kvm.h
Cc: Maxim Levitsky <mlevitsk@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kim Phillips [Tue, 17 Aug 2021 22:15:09 +0000 (17:15 -0500)]
perf report: Add support to print a textual representation of IBS raw sample data
Perf records IBS (Instruction Based Sampling) extra sample data when
'perf record --raw-samples' is used with an IBS-compatible event, on a
machine that supports IBS. IBS support is indicated in
CPUID_Fn80000001_ECX bit #10.
Up until now, users have been able to see the extra sample data solely
in raw hex format using 'perf report --dump-raw-trace'. From there,
users could decode the data either manually, or by using an external
script.
Enable the built-in 'perf report --dump-raw-trace' to do the decoding of
the extra sample data bits, so manual or external script decoding isn't
necessary.
Example usage:
$ sudo perf record -c 10000001 -a --raw-samples -e ibs_fetch/rand_en=1/,ibs_op/cnt_ctl=1/ -C 0,1 taskset -c 0,1 7za b -mmt2 | perf report --dump-raw-trace
util/amd-sample-raw.c: In function ‘evlist__amd_sample_raw’:
util/amd-sample-raw.c:125:42: error: ‘ bytes’ directive output may be truncated writing 6 bytes into a region of size between 4 and 7 [-Werror=format-truncation=]
125 | " OpMemWidth %2d bytes", 1 << (reg.op_mem_width - 1));
| ^~~~~~
In file included from /usr/include/stdio.h:866,
from util/amd-sample-raw.c:7:
/usr/include/bits/stdio2.h:71:10: note: ‘__builtin___snprintf_chk’ output between 21 and 24 bytes into a destination of size 21
71 | return __builtin___snprintf_chk (__s, __n, __USE_FORTIFY_LEVEL - 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
72 | __glibc_objsize (__s), __fmt,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
73 | __va_arg_pack ());
| ~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
As that %2d won't limit the number of chars to 2, just state that 2 is
the minimal width:
And since we probably don't want that output to be truncated, just
assume the worst case, as the compiler did, and add a few more chars to
that buffer.
Also use sizeof(var) instead of sizeof(dup-of-wanted-format-string) to
avoid bugs when changing one but not the other.
And change the check-headers.sh entry to ignore this line when diffing
with the original kernel header.
This is needed so that we can use 'perf report' on a perf.data with IBS
data on a !x86 system, i.e. building on ARM fails without this as there
is no asm/msr-index.h there.
This was done on the next patch in this series and is done for things
like Intel PT and ARM CoreSight.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Joao Martins <joao.m.martins@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Richter <robert.richter@amd.com> Cc: Stephane Eranian <eranian@google.com>
Link: https //lore.kernel.org/r/20210817221509.88391-3-kim.phillips@amd.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge tag 'acpi-5.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These prevent a confusing PRMT-related message from being printed,
drop an unnecessary header file include and update the list of ACPICA
maintainers.
Specifics:
- Prevent a message about missing PRMT from being printed on systems
that do not support PRM, which are the majority now (Aubrey Li).
- Drop unnecessary header include from scan.c (Kari Argillander).
- Update the list of ACPICA maintainers after recent departure of one
of them (Rafael Wysocki)"
* tag 'acpi-5.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Update the list of maintainers
ACPI: PRM: Find PRMT table before parsing it
ACPI: scan: Remove unneeded header linux/nls.h
Merge tag 'pm-5.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These improve hybrid processors support in intel_pstate, fix an issue
in the core devices PM code, clean up the handling of dedicated wake
IRQs, update the Energy Model documentation and update MAINTAINERS.
Specifics:
- Make the HWP performance levels calibration on hybrid processors in
intel_pstate more straightforward (Rafael Wysocki).
- Prevent the PM core from leaving devices in suspend after a failing
system-wide suspend transition in some cases when driver PM flags
are used (Prasad Sodagudi).
- Drop unused function argument from the dedicated wake IRQs handling
code (Sergey Shtylyov).
- Fix up Energy Model kerneldoc comments and include them in the
Energy Model documentation (Lukasz Luba).
- Use my kernel.org address in MAINTAINERS insead of the personal one
(Rafael Wysocki)"
* tag 'pm-5.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
MAINTAINERS: Change Rafael's e-mail address
PM: sleep: core: Avoid setting power.must_resume to false
Documentation: power: include kernel-doc in Energy Model doc
PM: EM: fix kernel-doc comments
cpufreq: intel_pstate: hybrid: Rework HWP calibration
ACPI: CPPC: Introduce cppc_get_nominal_perf()
PM: sleep: wakeirq: drop useless parameter from dev_pm_attach_wake_irq()
Rob Herring [Fri, 10 Sep 2021 16:59:45 +0000 (11:59 -0500)]
spi: dt-bindings: xilinx: Drop type reference on *-bits properties
Properties with standard unit suffixes such as '-bits' don't need a
type.
Cc: Mark Brown <broonie@kernel.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: linux-spi@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20210910165945.2852999-1-robh@kernel.org
Rob Herring [Fri, 10 Sep 2021 16:51:53 +0000 (11:51 -0500)]
dt-bindings: More use 'enum' instead of 'oneOf' plus 'const' entries
'enum' is equivalent to 'oneOf' with a list of 'const' entries, but 'enum'
is more concise and yields better error messages.
Fix a couple more cases which have appeared.
Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: Mark Brown <broonie@kernel.org> Cc: Wim Van Sebroeck <wim@linux-watchdog.org> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jonathan Marek <jonathan@marek.ca> Cc: Aswath Govindraju <a-govindraju@ti.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: dri-devel@lists.freedesktop.org Cc: freedreno@lists.freedesktop.org Cc: linux-spi@vger.kernel.org Cc: linux-watchdog@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20210910165153.2843871-1-robh@kernel.org
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Limit the linear region to 51-bit when KVM is running in nVHE mode.
Otherwise, depending on the placement of the ID map, kernel-VA to
hyp-VA translations may produce addresses that either conflict with
other HYP mappings or generate addresses outside of the 52-bit
addressable range.
- Instruct kmemleak not to scan the memory reserved for kdump as this
range is removed from the kernel linear map and therefore not
accessible.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kdump: Skip kmemleak scan reserved memory for kdump
arm64: mm: limit linear region to 51 bits for KVM in nVHE mode
Merge tag 'for-5.15/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
- Build warning fixes in Makefile and Dino PCI driver
- Fix when sched_clock is marked unstable
- Drop strnlen_user() in favour of generic version
- Prevent kernel to write outside userspace signal stack
- Remove CONFIG_SET_FS including KERNEL_DS and USER_DS from parisc and
switch to __get/put_kernel_nofault()
* tag 'for-5.15/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Implement __get/put_kernel_nofault()
parisc: Mark sched_clock unstable only if clocks are not syncronized
parisc: Move pci_dev_is_behind_card_dino to where it is used
parisc: Reduce sigreturn trampoline to 3 instructions
parisc: Check user signal stack trampoline is inside TASK_SIZE
parisc: Drop useless debug info and comments from signal.c
parisc: Drop strnlen_user() in favour of generic version
parisc: Add missing FORCE prerequisite in Makefile
Merge tag 'char-misc-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull habanalabs updates from Greg KH:
"Here is another round of misc driver patches for 5.15-rc1.
In here is only updates for the Habanalabs driver. This request is
late because the previously-objected-to dma-buf patches are all
removed and some fixes that you and others found are now included in
here as well.
All of these have been in linux-next for well over a week with no
reports of problems, and they are all self-contained to only this one
driver. Full details are in the shortlog"
* tag 'char-misc-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (61 commits)
habanalabs/gaudi: hwmon default card name
habanalabs: add support for f/w reset
habanalabs/gaudi: block ICACHE_BASE_ADDERESS_HIGH in TPC
habanalabs: cannot sleep while holding spinlock
habanalabs: never copy_from_user inside spinlock
habanalabs: remove unnecessary device status check
habanalabs: disable IRQ in user interrupts spinlock
habanalabs: add "in device creation" status
habanalabs/gaudi: invalidate PMMU mem cache on init
habanalabs/gaudi: size should be printed in decimal
habanalabs/gaudi: define DC POWER for secured PMC
habanalabs/gaudi: unmask out of bounds SLM access interrupt
habanalabs: add userptr_lookup node in debugfs
habanalabs/gaudi: fetch TPC/MME ECC errors from F/W
habanalabs: modify multi-CS to wait on stream masters
habanalabs/gaudi: add monitored SOBs to state dump
habanalabs/gaudi: restore user registers when context opens
habanalabs/gaudi: increase boot fit timeout
habanalabs: update to latest firmware headers
habanalabs/gaudi: minimize number of register reads
...
Merge tag 'drm-next-2021-09-10' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Just an initial bunch of fixes for the merge window, amdgpu is most of
them with a few ttm fixes and an fbdev avoid multiply overflow fix.
core:
- Make some dma-buf config options depend on DMA_SHARED_BUFFER
- Handle multiplication overflow of fbdev xres/yres in the core
ttm:
- Fix ttm_bo_move_memcpy() when ttm_resource is subclassed
- Fix ttm deadlock if target BO isn't idle
- ttm build fix
- ttm docs fix
dma-buf:
- config option fixes
fbdev:
- limit resolutions to avoid int overflow
i915:
- stddef change.
amdgpu:
- Misc cleanups, typo fixes
- EEPROM fix
- Add some new PCI IDs
- Scatter/Gather display support for Yellow Carp
- PCIe DPM fix for RKL platforms
- RAS fix
amdkfd:
- SVM fix
vc4:
- static function fix
mgag200:
- fix uninit var
panfrost:
- lock_region fixes"
* tag 'drm-next-2021-09-10' of git://anongit.freedesktop.org/drm/drm: (36 commits)
drm/ttm: Fix a deadlock if the target BO is not idle during swap
fbmem: don't allow too huge resolutions
dma-buf: DMABUF_SYSFS_STATS should depend on DMA_SHARED_BUFFER
dma-buf: DMABUF_DEBUG should depend on DMA_SHARED_BUFFER
drm/i915: use linux/stddef.h due to "isystem: trim/fixup stdarg.h and other headers"
dma-buf: DMABUF_MOVE_NOTIFY should depend on DMA_SHARED_BUFFER
drm/amdkfd: drop process ref count when xnack disable
drm/amdgpu: enable more pm sysfs under SRIOV 1-VF mode
drm/amdgpu: fix fdinfo race with process exit
drm/amdgpu: Fix a deadlock if previous GEM object allocation fails
drm/amdgpu: stop scheduler when calling hw_fini (v2)
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amd/display: Initialize lt_settings on instantiation
drm/amd/display: cleanup idents after a revert
drm/amd/display: Fix memory leak reported by coverity
drm/ttm: Fix ttm_bo_move_memcpy() for subclassed struct ttm_resource
drm/amdgpu/swsmu: fix spelling mistake "minimun" -> "minimum"
drm/amdgpu: Disable PCIE_DPM on Intel RKL Platform
drm/amdgpu: show both cmd id and name when psp cmd failed
drm/amd/display: setup system context for APUs
...
of: property: Disable fw_devlink DT support for X86
Andre reported fw_devlink=on breaking OLPC XO-1.5 [1].
OLPC XO-1.5 is an X86 system that uses a mix of ACPI and OF to populate
devices. The root cause seems to be ISA devices not setting their fwnode
field. But trying to figure out how to fix that doesn't seem worth the
trouble because the OLPC devicetree is very sparse/limited and fw_devlink
only adds the links causing this issue. Considering that there aren't many
users of OF in an X86 system, simply fw_devlink DT support for X86.
To be used by IBS raw data display: It needs the recorder's cpuid in
order to determine which errata workarounds to apply to the data, and
the pmu_mappings are needed in order to figure out which PMU sample
type is IBS Fetch vs. IBS Op.
When not available from perf.data, we assume local operation, and
retrieve cpuid and pmu mappings directly from the running system.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Joao Martins <joao.m.martins@oracle.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Richter <robert.richter@amd.com> Cc: Stephane Eranian <eranian@google.com>
Link: https //lore.kernel.org/r/20210817221509.88391-2-kim.phillips@amd.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf symbol: Look for ImageBase in PE file to compute .text offset
Instead of using the file offset in the debug file.
This fixes a regression from 410ebb2f243ba72c ("perf symbols: Make
dso__load_bfd_symbols() load PE files from debug cache only"), causing
incorrect symbol resolution when debug file have been stripped from
non-debug sections (in which case its .text section is empty and doesn't
have any file position).
The debug files could also be created with a different file alignment,
and have different file positions from the mmap-ed binary, or have the
section reordered.
This instead looks for the file image base, using the corresponding bfd
*ABS* symbols. As PE symbols only have 4 bytes, it also needs to keep
.text section vma high bits.
Signed-off-by: Remi Bernon <rbernon@codeweavers.com> Fixes: 410ebb2f243ba72c ("perf symbols: Make dso__load_bfd_symbols() load PE files from debug cache only") Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Nicholas Fraser <nfraser@codeweavers.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210909192637.4139125-1-rbernon@codeweavers.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Michael Petlan <mpetlan@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com>
LPU-Reference: 20200427142327.21172-1-mpetlan@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
That is the filter expression attached to the raw_syscalls:sys_{enter,exit}
tracepoints.
$ grep process_mrelease tools/perf/arch/x86/entry/syscalls/syscall_64.tbl
448 common process_mrelease sys_process_mrelease
$
This addresses these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/asm-generic/unistd.h' differs from latest version at 'include/uapi/asm-generic/unistd.h'
diff -u tools/include/uapi/asm-generic/unistd.h include/uapi/asm-generic/unistd.h
Warning: Kernel ABI header at 'tools/perf/arch/x86/entry/syscalls/syscall_64.tbl' differs from latest version at 'arch/x86/entry/syscalls/syscall_64.tbl'
diff -u tools/perf/arch/x86/entry/syscalls/syscall_64.tbl arch/x86/entry/syscalls/syscall_64.tbl
Warning: Kernel ABI header at 'tools/perf/arch/powerpc/entry/syscalls/syscall.tbl' differs from latest version at 'arch/powerpc/kernel/syscalls/syscall.tbl'
diff -u tools/perf/arch/powerpc/entry/syscalls/syscall.tbl arch/powerpc/kernel/syscalls/syscall.tbl
Warning: Kernel ABI header at 'tools/perf/arch/s390/entry/syscalls/syscall.tbl' differs from latest version at 'arch/s390/kernel/syscalls/syscall.tbl'
diff -u tools/perf/arch/s390/entry/syscalls/syscall.tbl arch/s390/kernel/syscalls/syscall.tbl
Warning: Kernel ABI header at 'tools/perf/arch/mips/entry/syscalls/syscall_n64.tbl' differs from latest version at 'arch/mips/kernel/syscalls/syscall_n64.tbl'
diff -u tools/perf/arch/mips/entry/syscalls/syscall_n64.tbl arch/mips/kernel/syscalls/syscall_n64.tbl
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf beauty: Update copy of linux/socket.h with the kernel sources
To pick the changes in:
Fixes: e6c22fb8b7ae0045 ("net: add accept helper not installing fd") Fixes: 936ac12d1fe1c8ea ("mctp: Add MCTP base")
This automagically adds support for the AF_MCTP protocol domain:
$ tools/perf/trace/beauty/socket.sh > before
$ cp include/linux/socket.h tools/perf/trace/beauty/include/linux/socket.h
$ tools/perf/trace/beauty/socket.sh > after
$ diff -u before after
--- before 2021-09-06 11:57:14.972747200 -0300
+++ after 2021-09-06 11:57:30.541920222 -0300
@@ -44,4 +44,5 @@
[42] = "QIPCRTR",
[43] = "SMC",
[44] = "XDP",
+ [45] = "MCTP",
};
$
This will allow 'perf trace' to translate 45 into "MCTP" as is done with
the other domains:
Warning: Kernel ABI header at 'tools/perf/trace/beauty/include/linux/socket.h' differs from latest version at 'include/linux/socket.h'
diff -u tools/perf/trace/beauty/include/linux/socket.h include/linux/socket.h
Cc: David S. Miller <davem@davemloft.net> Cc: Jens Axboe <axboe@kernel.dk> Cc: Jeremy Kerr <jk@codeconstruct.com.au> Cc: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
I have been slow to respond to messages going to rjw@rjwysocki.net
recently, so change it to rafael@kernel.org (which works better for
me) in MAINTAINERS.
Signed-off-by: Rafael J. Wysocki <rafael@kernel.org>
io_uring: fix off-by-one in BUILD_BUG_ON check of __REQ_F_LAST_BIT
Build check of __REQ_F_LAST_BIT should be larger than, not equal or larger
than. It's perfectly valid to have __REQ_F_LAST_BIT be 32, as that means
that the last valid bit is 31 which does fit in the type.
The reserved memory for kdump will be looked up by kmemleak, this area
will be set invalid when kdump service is bring up. That will result in
crash when kmemleak scan this area.
Fixes: bda8fda6df11 ("memblock: make memblock_find_in_range method private") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/20210910064844.3827813-1-chenwandun@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
xinhui pan [Tue, 7 Sep 2021 04:08:32 +0000 (12:08 +0800)]
drm/ttm: Fix a deadlock if the target BO is not idle during swap
The ret value might be -EBUSY, caller will think lru lock is still
locked but actually NOT. So return -ENOSPC instead. Otherwise we hit
list corruption.
ttm_bo_cleanup_refs might fail too if BO is not idle. If we return 0,
caller(ttm_tt_populate -> ttm_global_swapout ->ttm_device_swapout) will
be stuck as we actually did not free any BO memory. This usually happens
when the fence is not signaled for a long time.
Signed-off-by: xinhui pan <xinhui.pan@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Fixes: bae0bb5cb9c3 ("drm/ttm: move swapout logic around v3") Link: https://patchwork.freedesktop.org/patch/msgid/20210907040832.1107747-1-xinhui.pan@amd.com Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 10 Sep 2021 04:18:33 +0000 (14:18 +1000)]
Merge tag 'drm-misc-next-fixes-2021-09-09' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next-fixes for v5.15:
- Make some dma-buf config options depend on DMA_SHARED_BUFFER.
- Handle multiplication overflow of fbdev xres/yres in the core.
Merge tag '5.15-rc-ksmbd-part2' of git://git.samba.org/ksmbd
Pull ksmbd fixes from Steve French:
- various fixes pointed out by coverity, and a minor cleanup patch
- id mapping and ownership fixes
- an smbdirect fix
* tag '5.15-rc-ksmbd-part2' of git://git.samba.org/ksmbd:
ksmbd: fix control flow issues in sid_to_id()
ksmbd: fix read of uninitialized variable ret in set_file_basic_info
ksmbd: add missing assignments to ret on ndr_read_int64 read calls
ksmbd: add validation for ndr read/write functions
ksmbd: remove unused ksmbd_file_table_flush function
ksmbd: smbd: fix dma mapping error in smb_direct_post_send_data
ksmbd: Reduce error log 'speed is unknown' to debug
ksmbd: defer notify_change() call
ksmbd: remove setattr preparations in set_file_basic_info()
ksmbd: ensure error is surfaced in set_file_basic_info()
ndr: fix translation in ndr_encode_posix_acl()
ksmbd: fix translation in sid_to_id()
ksmbd: fix subauth 0 handling in sid_to_id()
ksmbd: fix translation in acl entries
ksmbd: fix translation in ksmbd_acls_fattr()
ksmbd: fix translation in create_posix_rsp_buf()
ksmbd: fix translation in smb2_populate_readdir_entry()
ksmbd: fix lookup on idmapped mounts
bootconfig: Rename xbc_node_find_child() to xbc_node_find_subkey()
Rename xbc_node_find_child() to xbc_node_find_subkey() for
clarifying that function returns a key node (no value node).
Since there are xbc_node_for_each_child() (loop on all child
nodes) and xbc_node_for_each_subkey() (loop on only subkey
nodes), this name distinction is necessary to avoid confusing
users.
tracing/boot: Fix to check the histogram control param is a leaf node
Since xbc_node_find_child() doesn't ensure the returned node
is a leaf node (key-value pair or do not have subkeys),
use xbc_node_find_value to ensure the histogram control
parameter is a leaf node in trace_boot_compose_hist_cmd().
tracing/boot: Fix trace_boot_hist_add_array() to check array is value
trace_boot_hist_add_array() uses the combination of
xbc_node_find_child() and xbc_node_get_child() to get the
child node of the key node. But since it missed to check
the child node is data node or not, user can pass the
subkey node for the array node (anode).
To avoid this issue, check the array node is a data node.
Actually, there is xbc_node_find_value(node, key, vnode),
which ensures the @vnode is a value node, so use it in
trace_boot_hist_add_array() to fix this issue.
Merge tag 'for-5.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix max_inline mount option limit on 64k page system
- lockdep fixes:
- update bdev time in a safer way
- move bdev put outside of sb write section when removing device
- fix possible deadlock when mounting seed/sprout filesystem
- zoned mode: fix split extent accounting
- minor include fixup
* tag 'for-5.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix double counting of split ordered extent
btrfs: fix lockdep warning while mounting sprout fs
btrfs: delay blkdev_put until after the device remove
btrfs: update the bdev time directly when closing
btrfs: use correct header for div_u64 in misc.h
btrfs: fix upper limit for max_inline for page size 64K
Merge tag 'sound-fix-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes that have been gathered before rc1,
including a few regression fixes for the problem in the previous pull
request"
* tag 'sound-fix-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: gus: Fix repeated probe for ISA interwave card
ALSA: gus: Fix repeated probes of snd_gus_create()
ALSA: vx222: fix null-ptr-deref
ASoC: rockchip: i2s: Fix concurrency between tx/rx
ASoC: mt8195: correct the dts parsing logic about DPTX and HDMITX
ASoC: Intel: boards: Fix CONFIG_SND_SOC_SDW_MOCKUP select
ASoC: dt-bindings: fsl_rpmsg: Add compatible string for i.MX8ULP
ALSA: usb-audio: Add registration quirk for JBL Quantum 800
ASoC: rt5682: fix headset background noise when S3 state
ASoC: dt-bindings: mt8195: remove dependent headers in the example
ASoC: mediatek: SND_SOC_MT8195 should depend on ARCH_MEDIATEK
ASoC: samsung: s3c24xx_simtec: fix spelling mistake "devicec" -> "device"
ASoC: audio-graph: respawn Platform Support
ASoC: mediatek: mt8195: add MTK_PMIC_WRAP dependency
cifs: properly invalidate cached root handle when closing it
Cached root file was not being completely invalidated sometimes.
Reproducing:
- With a DFS share with 2 targets, one disabled and one enabled
- start some I/O on the mount
# while true; do ls /mnt/dfs; done
- at the same time, disable the enabled target and enable the disabled
one
- wait for DFS cache to expire
- on reconnect, the previous cached root handle should be invalid, but
open_cached_dir_by_dentry() will still try to use it, but throws a
use-after-free warning (kref_get())
Make smb2_close_cached_fid() invalidate all fields every time, but only
send an SMB2_close() when the entry is still valid.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
projects / kernel.git / log