Allow using different PHY interfaces for multiple USB controllers. When no
value is set in DT, we fall back to CONFIG_MXC_USB_PORTSC for now to stay
compatible with current board configurations.
This also adds support for the HSIC mode of the i.MX7.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Samuel Holland [Mon, 5 Jul 2021 12:29:03 +0000 (13:29 +0100)]
usb: xhci-dwc3: Add support for clocks/resets
Some platforms, like the Allwinner H6, do not have a separate glue layer
around the dwc3. Instead, they rely on the clocks/resets/phys referenced
from the dwc3 DT node itself. Add support for enabling the clocks/resets
referenced from the dwc3 DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 5 Jul 2021 12:29:02 +0000 (13:29 +0100)]
usb: xhci-pci: Move reset logic out of XHCI core
Resetting an XHCI controller inside xhci_register undoes any register
setup performed by the platform driver. And at least on the Allwinner
H6, resetting the XHCI controller also resets the PHY, which prevents
the controller from working. That means the controller must be taken out
of reset before initializing the PHY, which must be done before calling
xhci_register.
The logic in the XHCI core was added to support the Raspberry Pi 4
(although this was not mentioned in the commit log!), which uses the
xhci-pci platform driver. Move the reset logic to the platform driver,
where it belongs, and where it cannot interfere with other platform
drivers.
This also fixes a failure to call reset_free if xhci_register failed.
Fixes: b6f9fe1c71b6 ("usb: xhci: Add reset controller support") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Mon, 5 Jul 2021 12:29:01 +0000 (13:29 +0100)]
phy: sun50i-usb3: Add a driver for the H6 USB3 PHY
This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andy Shevchenko [Sat, 11 Sep 2021 18:27:42 +0000 (21:27 +0300)]
x86: tangier: acpi: Add GPIO card detection to SDHCI #2
On Intel Tangier the SDHCI #2 provides SD card connection.
Add GPIO card detection for it.
Fixes: 6866a3c6df33 ("x86: tangier: Enable ACPI support for Intel Tangier") BugLink: https://github.com/edison-fw/meta-intel-edison/issues/135 Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Bin Meng <bmeng.cn@gmail.com>
Sean Anderson [Sat, 11 Sep 2021 19:11:30 +0000 (15:11 -0400)]
wdt: dw: Fix passing NULL pointer to reset functions
reset_*_bulk expects a real pointer.
Fixes: 910beba2d2 ("driver: watchdog: reset watchdog in designware_wdt_stop() function") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Nishanth Menon [Tue, 31 Aug 2021 18:20:48 +0000 (13:20 -0500)]
arm: mach-k3: common: Make sure firmware sections are loaded prior to armv8 startup
With Device Manager firmware in an elf file form, we cannot load the FIT
image to the exact same address as any of the executable sections of the
elf file itself is located.
However, the device tree descriptions for the ARMV8 bootloader/OS
includes DDR regions only the final sections in DDR where the Device
Manager firmware is actually executing out of.
As the R5 uC is usually operating at a slower rate than an ARMv8 MPU,
by starting the Armv8 ahead of parsing the elf and copying the correct
sections to the required memories creates a race condition where the
ARMv8 could overwrite the elf image loaded from the FIT image prior to
the R5 completing parsing and putting the correct sections of elf in
the required memory locations. OR create rather obscure debug conditions
where data in the section is being modified by ARMV8 OS while the elf
copy is in progress.
To prevent all these conditions, lets make sure that the elf parse and
copy operations are completed ahead of ARMv8 being released to execute.
We will pay a penalty of elf copy time, but that is a valid tradeoff in
comparison to debug of alternate scenarios.
Roger Quadros [Wed, 8 Sep 2021 20:28:59 +0000 (15:28 -0500)]
arm: mach-k3: am6_init: Prioritize MSMC traffic over DDR in NAVSS Northbridge
NB0 is bridge to SRAM and NB1 is bridge to DDR.
To ensure that SRAM transfers are not stalled due to delays during DDR
refreshes, SRAM traffic should be higher priority (threadmap=2) than
DDR traffic (threadmap=0).
This fixup is critical to provide deterministic access latency to
MSMC from ICSSG, it applies to all AM65 silicon revisions and is due
to incorrect reset values (has no erratum id) and statically setting
things up should be done independent of usecases and board.
This specific style of Northbridge configuration is specific only to
AM65x devices, follow-on K3 devices have different data prioritization
schemes (ASEL and the like) and hence the fixup applies purely to
AM65x.
Without this fix, ICSSG TX lock-ups due to delays in MSMC transfers in
case of SR1 devices, on SR2 devices, lockups were not observed so far
but high retry rates of ICSSG Ethernet (icssg-eth) and, thus, lower
throughput.
Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Andrew F. Davis <afd@ti.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Benoit Parrot <bparrot@ti.com>
[Jan: rebased, dropped used define, extended commit log] Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
[Nishanth: Provide relevant context in the commit message] Signed-off-by: Nishanth Menon<nm@ti.com>
Suman Anna [Tue, 7 Sep 2021 22:16:58 +0000 (17:16 -0500)]
clk: ti: k3: Update driver to account for divider flags
The K3 SoCs have some PLL output clocks (POSTDIV clocks) which in
turn serve as inputs to other HSDIV output clocks. These clocks use
the actual value to compute the divider clock rate, and need to be
registered with the CLK_DIVIDER_ONE_BASED flags. The current k3-clk
driver and data lacks the infrastructure to pass in divider flags.
Update the driver and data to account for these divider flags.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Dave Gerlach [Tue, 7 Sep 2021 22:16:57 +0000 (17:16 -0500)]
clk: ti: k3-pll: Change DIV_CTRL programming to read-modify-write
There are three different divider values in the DIV_CTRL register
controlled by the k3-pll driver. Currently the ti_pll_clk_set_rate
function writes the entire register when programming plld, even though
plld only resides in the lower 6 bits.
Change the plld programming to read-modify-write to only affect the
relevant bits for plld and to preserve the other two divider values
present in the upper 16 bits, otherwise they will always get set to zero
when programming plld.
Fixes: 5a5f3984a2f7 ("clk: add support for TI K3 SoC PLL") Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Dave Gerlach [Tue, 7 Sep 2021 22:16:56 +0000 (17:16 -0500)]
arm: mach-k3: Add note to auto-generated files
Add a note to the automatically generated clk-data and dev-data files
for j721e and j7200 to indicate that they are in fact auto-generated and
should not be hand edited.
Also adjust TI URL to use https instead of http and also add an empty
line before first header inclusion.
Suman Anna [Tue, 7 Sep 2021 22:16:55 +0000 (17:16 -0500)]
arm: mach-k3: j7200: Fix clk-data parenting for postdiv PLL clocks
The TI K3 Fractional PLLs use two programmable POSTDIV1 and POSTDIV2
divisors to generate the final FOUTPOSTDIV clock. These are in sequence
with POSTDIV2 following the POSTDIV1 clock. The current J7200 clock data
has the POSTDIV2 clock as the parent for the POSTDIV1 clock, which is
opposite of the actual implementation. Fix the data by simply adjusting
the register bit-shifts.
The Main PLL1 POSTDIV clocks were also defined incorrectly using Main PLL0
register values, fix these as well.
Fixes: 912547a6c636 ("arm: mach-k3: Add platform data for j721e and j7200") Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Suman Anna [Tue, 7 Sep 2021 22:16:54 +0000 (17:16 -0500)]
arm: mach-k3: j721e: Fix clk-data parenting for postdiv PLL clocks
The TI K3 Fractional PLLs use two programmable POSTDIV1 and POSTDIV2
divisors to generate the final FOUTPOSTDIV clock. These are in sequence
with POSTDIV2 following the POSTDIV1 clock. The current J721E clock data
has the POSTDIV2 clock as the parent for the POSTDIV1 clock, which is
opposite of the actual implementation. Fix the data by simply adjusting
the register bit-shifts.
The Main PLL1 POSTDIV clocks were also defined incorrectly using Main PLL0
register values, fix these as well.
Fixes: 912547a6c636 ("arm: mach-k3: Add platform data for j721e and j7200") Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Suman Anna [Tue, 27 Jul 2021 23:24:39 +0000 (18:24 -0500)]
firmware: ti_sci: Include linux/err.h in ti_sci_protocol.h
The common TI SCI header file uses some macros from err.h and these
get exercised when CONFIG_TI_SCI_PROTOCOL is not defined. Include
the linux/err.h header file in this header file directly rather
than relying on source files to include it to eliminate any
potential build errors.
While at this, reorder the existing header file include to the
beginning of the file.
Signed-off-by: Suman Anna <s-anna@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com>
Tom Rini [Wed, 15 Sep 2021 19:22:46 +0000 (15:22 -0400)]
Merge branch 'rpi-next' of https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
Ivan's patch fixes a kernel warning when booting RPi2, as the firmware
already
provides a frambebuffer node.
Marek's patch fixes random crashes on 32 bit RPi4 with newer firmware.
My SMBIOS patchesfixes an issue that show up with f274b45aeb ("smbios: Drop the unused Kconfig options").
Basically the SMBIOS table broke and wasn't readable anymore.
Ivan T. Ivanov [Tue, 10 Aug 2021 14:31:14 +0000 (16:31 +0200)]
rpi: Conditionally add simple-framebuffer node
It appears that RPi firmware has already added framebuffer
node under /chosen, at least on RPi 2 versions. So check
for this and don't add duplicate node.
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Marek Szyprowski [Thu, 17 Jun 2021 09:22:03 +0000 (11:22 +0200)]
ARM: bcm283x: change the virtual address of the XHCI PCI device base
Move the XHCI PCI device base up in the virtual address space. This fixes
initialization failure observed with newer Raspberry Pi firmware, later
than 63b1922311 ("firmware: arm_loader: Update armstubs with those from
PR 117). It looks that chosing 0xff800000 as the XHCI PCI device base
conflicts with the updated ARM/VideoCore firmware.
This also requires to reduce the size of the mapped PCI device region
from 8MiB to 4MiB to fit into 32bit address space. This is still enough
for the XHCI PCI device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Tested-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
image: Avoid erroneous double byte-swap in CRC value
The hash algorithm selection was streamlined in commit 1affd3abbe04
("image: Drop if/elseif hash selection in calculate_hash()"). Said
commit kept the call to cpu_to_uimage() to convert the CRC to big
endian format.
This would have been correct when calling crc32_wd(). However, the
->hash_func_ws member of crc32 points to crc32_wd_buf(), which already
converts the CRC to big endian. On a little endian host, doing both
conversions results in a little-endian CRC. This is incorrect.
To remedy this, simply drop the call to cpu_to_uimage(), thus only
doing the byte-order conversion once.
Fixes: 1affd3abbe04 ("image: Drop if/elseif hash selection in
calculate_hash()") Tested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
We are not guaranteed to have the padding_pkcs_15_verify symbol since
commit c65490f151 ("lib: rsa: Remove #ifdefs from rsa.h"), and
commit 6de87750ba ("Kconfig: FIT_SIGNATURE should not select RSA_VERIFY")
The padding_algos only make sense with RSA verification, which can now
be disabled in lieu of ECDSA. In fact this will lead to build failures
because of the missing symbol mentioned earlier.
To resolve this, move the padding_algos to a linker list, with
declarations moved to rsa_verify.c. This is consistent with commit 46dbd3b0bd ("image: rsa: Move verification algorithm to a linker list")
One could argue that the added #ifdef USE_HOSTCC is ugly, and should
be hidden within the U_BOOT_PADDING_ALGO() macro. However, this would
be inconsistent with the "cryptos" list. This logic for was not
previously explored:
Without knowledge of the U_BOOT_PADDING_ALGO() macro, its use is
similar to something being declared. However, should #ifndef
USE_HOSTCC be part of the macro, it would not be obvious that it
behaves differently on host code and target code. Having the #ifndef
outside the macro makes this obvious.
Also, the #ifdef is not always necessary. For example ecda-verify
makes use of U_BOOT_CRYPTO_ALGO() without any accompanying #ifdefs.
The fundamental issue is a lack of separation of host and target code
in rsa_verify. Therefore, the declaration of a padding algo with the
external #ifdef is more readable and consistent.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
If keydir is not provided but name is we want to use name as key_id.
But with the current coding name is only used on its own if it is NULL
and keydir is provided which never occurs.
Fixes: 16840b08c02b ("lib/rsa: Use the 'keyfile' argument from mkimage") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Andre Przywara [Fri, 3 Sep 2021 15:49:16 +0000 (16:49 +0100)]
sunxi: mmc: A20: Fix MMC optimisation
Some SoCs (as seen on A20) seem to misreport the MMC FIFO level if the
FIFO is completely full: the level size reads as zero, but the FIFO_FULL
bit is set. We won't do a single iteration of the read loop in this
case, so will be stuck forever.
Check for this situation and use a safe minimal FIFO size instead when
we hit this case.
This fixes MMC boot on A20 devices after the MMC FIFO optimisation
(418ae1f13027).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Mon, 13 Sep 2021 12:31:41 +0000 (08:31 -0400)]
Merge tag 'mmc-2021-9-13' of https://source.denx.de/u-boot/custodians/u-boot-mmc
Support using mmc command for enumerating mmc card in a given mode
Fix device_remove in mmc
Fix switch issue with send_status disabled
Drop 1ms delay in fsl_esdhc command sending
Revert "mmc: sdhci: set to INT_DATA_END when there are data"
Michael Walle [Fri, 10 Sep 2021 09:20:52 +0000 (11:20 +0200)]
mmc: fsl_esdhc: remove 1ms sleep in esdhc_send_cmd_common()
Since the beginning of this driver which was initially for the MPC8379
and MPC8536 SoCs, there is this spurious 1ms delay. According to the
comment it should actually be only 8 clock cycles. Esp. during EFI block
transfers, this 1ms add up to a significant delay and slows down EFI
boot.
I couldn't find any mention in the MPC8536 that there should be a delay
of 8 clock cycles between commands. The SD card specification mentions that
the clock has to be left enabled for 8 cycles after a command or
response. But I don't see how this delay will help with this.
Go ahead and just remove it. If there will ever be any regression we can
introduce a compile time flag, but for now I'd like to keep it simple.
In the split off imx driver this delay was also removed in commit 8a4ed4e2734f ("mmc: fsl_esdhc_imx: remove the 1ms delay before sending
command").
efi_loader: Remove incorrect calls of EFI_CALL in TCG2
There is two unneeded EFI_CALL references in tcg2_measure_pe_image().
The first one in efi_search_protocol() and the second on in the device path
calculation. The second isn't even a function we should be calling, but a
pointer assignment, which happens to work with the existing macro.
While at it switch the malloc call to a calloc, remove the unnecessary cast
and get rid of an unneeded if statement before copying the device path
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The move to driver model should by now be completed. To be able to remove
pre-driver model code from our block IO code require CONFIG_BLK=y for UEFI
support.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Thu, 9 Sep 2021 20:10:31 +0000 (14:10 -0600)]
doc: Tidy up the bindings for the config/ node
Sort these and add a type so it is clear how to set the value. Add a note
about usage to the top. Correct the 'no-keyboard' binding which is missing
a prefix.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
configs: j72*_evm: Define the buffer sizes for dfu
On J721e R5 SPL, dfu buffer for loading sysfw.itb image gets allocated
before DRAM gets initialized. So, the buffer gets allocated in MCU L3
RAM. The current buffer size to be allocated is 256KB and the available
total heap memory is 0x70000 (448KB). This leads to NOMEM errors during
allocation.
In other cases when constraints such as above are not present fix the size
of buffers to the sector size in OSPI for proper functioning.
Also, if CONFIG_SYS_DFU_DATA_BUF_SIZE is defined and
CONFIG_SYS_DFU_MAX_FILE_SIZE is not defined then the max file size for dfu
transfer is defined as CONFIG_SYS_DFU_DATA_BUF_SIZE.
Fix these by setting appropriate buffer sizes in their respective defconfig
files and defining the max file size as 8 MB which is the default dfu
buffer size.
environment: ti: k3_dfu: Increase the size allocated for bootloader images in dfu_alt_info_ram
The size of u-boot.img is above 1MB and that of tispl.bin is close to 1MB,
in case of j721e. Therefore, increase the sizes allocated for tispl.bin and
u-boot.img to 2 MB and 4 MB respectively, in dfu_alt_info_ram environment
variable.
arm: dts: k3-j721e-r5-*.dts: Fix clock-names property in the usb0 instance
In the cdns3 usb driver, the clock name looked for is ref. Therefore, fix
the clock-names property in usb0 instance for proper initialization of
cdns3 usb gadget driver.
Suman Anna [Sat, 14 Aug 2021 06:49:01 +0000 (01:49 -0500)]
tools: k3_fit_atf: Fix DM binary FIT load addresses
The DM binary runs on the MCU R5F Core0 after R5 SPL on J721E and J7200
SoCs. The binary is built alongside the TFA, OPTEE and A72 SPL binaries
and included in the tispl.bin FIT image. The R5 SPL loads the DM binary
at 0xA0000000 address, based on the value used in the FIT image build
script. The DM binary though is an ELF image and not a regular binary
file, and so is processed further to load the actual program segments
using the U-Boot's standard ELF loader library.
The DM binary does leverage a certain portion of DDR for its program
segments, and typically reserves 16 MB of DDR at 0xA0000000 with the
1st MB used for IPC between Linux and the remote processor, and
remaining memory for firmware segments. This can cause an incomplete
loading of the program segments if the DM binary is larger than 1 MB,
due to overlap of the initial loaded binary and the actual program
segments.
Fix this by using the address 0x89000000, which matches the current
"addr_mcur5f0_0load" env variable used by R5 SPL before the DM firmware
inclusion into the tispl.bin.
Fixes: c3805ceee22d ("tools: k3_fit_atf: add DM binary to the FIT image") Signed-off-by: Suman Anna <s-anna@ti.com>
include: configs: am64x_evm: Add env variables for booting to kernel using USB MSC device
Add env variables for booting to kernel from USB MSC device. The second
partition in the USB MSC device needs to formatted as ext4 file system with
kernel and dtb images, present in the /boot folder.
environment: ti: mmc.h: Make the finduuid generic for usage across different device types
Make finduuid generic by making it dependent on the boot variable. For
example, this can now be used for finding the uuid of partitions in usb
device too.
board: ti: am64x: Add support for fixing dr_mode while booting from USB
Fix the dr_mode in the U-Boot device tree blob, by reading the mode field
from the USB Boot Configuration fields. The dr_mode will only be fixed when
booting from USB.
Derald D. Woods [Mon, 2 Aug 2021 03:46:19 +0000 (03:46 +0000)]
ARM: omap3: evm: Enable booting 'fitImage' with DEFAULT_FIT_TI_ARGS
This commit uses the existing DEFAULT_MMC_TI_ARGS and
DEFAULT_FIT_TI_ARGS defintions to replace the 'mmc*' environment
variables in the configuration. The check for the 'boot_fit' is handled
like the 'am335x_*' boards with 'CONFIG_BOOTCOMMAND'.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
mmc: Add support for enumerating MMC card in a given mode using mmc command
Add support for enumerating MMC card in a given mode using mmc rescan and
mmc dev commands. The speed mode is provided as the last argument in these
commands and is indicated using the index from enum bus_mode in
include/mmc.h. A speed mode can be set only if it has already been enabled
in the device tree.
In eMMC specification, for the response-with-busy(R1b, R5b)
command, the DAT0 will driven to LOW as BUSY status, and in
sdhci specification, the transfer complete bit should be wait
for BUSY status de-assert.
All response-with-busy commands don't contain data, the data
judgement is no need.
Marek Behún [Tue, 7 Sep 2021 15:27:08 +0000 (17:27 +0200)]
arm: a37xx: pci: Don't spam about PIO Response Status
Use dev_dbg() instead of dev_err() in pcie_advk_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Without this, U-Boot spams the terminal with
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x100000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x108000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x110000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x120000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x128000
pcie_advk pcie@d0070000: Non-posted PIO Response Status: UR, 0xc80 @ 0x130000
...
when a device is not connected to a PCIe switch (Unsupported Request
from the switch).
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tony Dinh [Sun, 5 Sep 2021 21:48:25 +0000 (14:48 -0700)]
arm: mvebu : sata_mv should probe all ports
While a board could have multiple SATA ports, some of the ports might
not have a disk attached to them. So while probing for disks,
sata_mv_probe() should continue probing all ports, and skip one with
no disk attached.
If a board has 2 or more SATA ports, and there is only one disk
attached to one of the ports, sata_mv_probe() does not return
a successful probe status. And if only one disk is attached to the
2nd port (i.e. port 1), it is not probed at all.
Patch Description:
Let sata_mv_probe() continues probing all ports, even if there
is error in probing a given port, and then return a successful
status if there is at least one port was probed successfully.
Signed-off-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Fix baudrate value 5150000 which was added in commit 4b55f8417e7f ("arm:
mvebu: a38x: Define supported UART baudrates").
Exact value for divisor 3 with 250 MHz TCLK is 5208333 baudrate. In above
commit I incorrectly rounded it to 5150000 value due to testing with
USB-UART hw which incorrectly reported exact value and divisor configured
on other other end of UART link.
Fix this value to 520000 baudrate which is more close to the exact hardware
value and also has less fraction parts.
Pali Rohár [Fri, 27 Aug 2021 12:14:44 +0000 (14:14 +0200)]
arm: a37xx: pci: Implement re-issuing config requests on CRS response
According to PCIe base specification, if CRS Software Visibility is not
enabled, the Root Complex must re-issue the Configuration Request as a new
Request.
Normally this part of Root Complex is implemented in hardware but aardvark
is somehow special and does not implement it in hardware and expect that
handling of config requests are fully implemented in software.
This re-issuing functionality is required also because U-Boot does not
support CRS Software Visibility feature and therefore expects that Root
Complex re-issues requests as is specified in PCIe base specification.
Retry / re-issue config request up to the PIO_MAX_RETRIES, to prevent
infinite loop. After retry count exceed PIO_MAX_RETRIES, returns failure.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 27 Aug 2021 12:14:43 +0000 (14:14 +0200)]
arm: a37xx: pci: Disable returning CRS response
There was mistake in commit a38d8e93a813 ("arm: a37xx: pci: Fix handling
PIO config error responses"). U-Boot does not support handling of CRS
return value for PCI_VENDOR_ID config read request and also does not set
CRSSVE bit.
Therefore disable returning CRS response for now.
Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: a38d8e93a813 ("arm: a37xx: pci: Fix handling PIO config error responses") Reviewed-by: Stefan Roese <sr@denx.de>
Sven Auhagen [Tue, 24 Aug 2021 08:14:25 +0000 (10:14 +0200)]
arm: mvebu: dts: Armada8k enable mdio
Since mvpp2 is using the new mdio driver and the cp110 has been
synced with the linux upstream, the mdio has to enabled in the
device tree file.
This is missing for some device tree files and therefore the
network cards do not come online.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Reviewed-by: Stefan Roese <sr@denx.de>
Move TI maintainership to Tom.
Updated with the following commands:
find ./ -name MAINTAINERS | xargs sed -i s/"Lokesh Vutla <lokeshvutla@ti.com>"/"Tom Rini <trini@konsulko.com>"/g
Tom Rini [Thu, 9 Sep 2021 14:57:34 +0000 (10:57 -0400)]
Kconfig: Drop duplicate 'select SHA512' instances
When dropping SHA512_ALGO in general, we didn't catch some cases where
an option was selecting both SHA512 and SHA512_ALGO and caused them to
select SHA512 twice. Kconfig doesn't complain, but this is still wrong
and should be corrected.
Fixes: 9af0d2c9ecf9 ("lib: Drop SHA512_ALGO in lieu of SHA512") Reported-by: Andreas Schwab <schwab@suse.de> Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
- Merge some fixes to how we enable hash algorithms for FIT images in
SPL. This fixes a few cases where we should have had some options
enabled, but did not. This also removes otherwise unused options in a
few other cases.
image: Drop if/elseif hash selection in calculate_hash()
calculate_hash() would try to select the appropriate hashing function
by a if/elseif contruct. But that is exactly why hash_lookup_algo()
exists, so use it instead.
This does mean that we now have to 'select HASH' to make sure we get
the hash_lookup_algo() symbol. However, the change makes sense because
even basic FITs will have to deal with "hash" nodes.
My only concern is that the 'select SPL_HASH' might cause some
platform to grow above its SPL size allowance
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Make FSL_CAAM be implied only on ARM && SPL] Signed-off-by: Tom Rini <trini@konsulko.com>
MD5 is being called directly in some places, but it is not available
via hash_lookup_algo("md5"). This is inconsistent with other hasing
routines. To resolve this, add an "md5" entry to hash_algos[].
The #ifdef clause looks funnier than those for other entries. This is
because both MD5 and SPL_MD5 configs exist, whereas the other hashes
do not have "SPL_" entries. The long term plan is to get rid of the
ifdefs, so those should not be expected to survive much longer.
The md5 entry does not have .hash_init/update/finish members. That's
okay because hash_progressive_lookup_algo() will catch that, and
return -EPROTONOSUPPORT, while hash_lookup_algo() will return the
correct pointer.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Use CONFIG_IS_ENABLED not IS_ENABLED for MD5 check] Signed-off-by: Tom Rini <trini@konsulko.com>
common/spl: Drop [ST]PL_HASH_SUPPORT in favor of [ST]PL_HASH
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks] Signed-off-by: Tom Rini <trini@konsulko.com>
SHA512_ALGO was used as a "either SHA512 or SHA384", although the
implementations of these two algorithms share a majority of code.
From a Kconfig interface perspective, it makes sense to present two
distinct options. This requires #ifdefing out the SHA512
implementation from sha512.c. The latter doesn't make any sense.
It's reasonable to say in Kconfig that SHA384 depends on SHA512, and
seems to be the more polite way to handle the selection.
Thus, automatically select SHA512 when SHA384 is enabled.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
projects / uboot.git / log