but the one in the kerneldoc comment of the function is different and
incorrect.
Fixes: e2ed2a3bd68a ("PM / Hibernate: Add sysfs knob to control size of memory for drivers") Signed-off-by: xiongxin <xiongxin@kylinos.cn>
[ rjw: Subject and changelog rewrite ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We only want to take the slow path if SYSCALL_TRACE or SYSCALL_AUDIT is
set; on !AUDIT_SYSCALL configs the current tree hits it whenever _any_
thread flag (including NEED_RESCHED, NOTIFY_SIGNAL, etc.) happens to
be set.
While we correctly skips to initialize an idle state from a disabled idle
state node in DT, the returned value from dt_init_idle_driver() don't get
adjusted accordingly. Instead the number of found idle state nodes are
returned, while the callers are expecting the number of successfully
initialized idle states from DT.
This leads to cpuidle drivers unnecessarily continues to initialize their
idle state specific data. Moreover, in the case when all idle states have
been disabled in DT, we would end up registering a cpuidle driver, rather
than relying on the default arch specific idle call.
Fixes: ec6a4264d9cc ("drivers: cpuidle: implement DT based idle states infrastructure") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error message in __crb_relinquish_locality() mentions requestAccess
instead of Relinquish. Fix it.
Fixes: cda64942039b ("tpm: cmd_ready command can be issued only after granting locality") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An oops can be induced by running 'cat /proc/kcore > /dev/null' on
devices using pstore with the ram backend because kmap_atomic() assumes
lowmem pages are accessible with __va().
During early boot, memblock reserves the pages for the ramoops reserved
memory node in DT that would otherwise be part of the direct lowmem
mapping. Pstore's ram backend reuses those reserved pages to change the
memory type (writeback or non-cached) by passing the pages to vmap()
(see pfn_to_page() usage in persistent_ram_vmap() for more details) with
specific flags. When read_kcore() starts iterating over the vmalloc
region, it runs over the virtual address that vmap() returned for
ramoops. In aligned_vread() the virtual address is passed to
vmalloc_to_page() which returns the page struct for the reserved lowmem
area. That lowmem page is passed to kmap_atomic(), which effectively
calls page_to_virt() that assumes a lowmem page struct must be directly
accessible with __va() and friends. These pages are mapped via vmap()
though, and the lowmem mapping was never made, so accessing them via the
lowmem virtual address oopses like above.
Let's side-step this problem by passing VM_IOREMAP to vmap(). This will
tell vread() to not include the ramoops region in the kcore. Instead the
area will look like a bunch of zeros. The alternative is to teach kmap()
about vmalloc areas that intersect with lowmem. Presumably such a change
isn't a one-liner, and there isn't much interest in inspecting the
ramoops region in kcore files anyway, so the most expedient route is
taken for now.
Cc: Brian Geffon <bgeffon@google.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: b2943781f3b0 ("staging: android: persistent_ram: handle reserving and mapping memory") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20221205233136.3420802-1-swboyd@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
timer_read() was using an empty 100-iteration loop to wait for the
TMR_CVWR register to capture the latest timer counter value. The delay
wasn't long enough. This resulted in CPU idle time being extremely
underreported on PXA168 with CONFIG_NO_HZ_IDLE=y.
Switch to the approach used in the vendor kernel, which implements the
capture delay by reading TMR_CVWR a few times instead.
Fixes: 8c975c48b032 ("[ARM] pxa: add base support for Marvell's PXA168 processor line") Signed-off-by: Doug Brown <doug@schmorgal.com> Link: https://lore.kernel.org/r/20221204005117.53452-3-doug@schmorgal.com Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the if (dev_of_node(dev) && !pdata) path, the "err" may be assigned a
value of 0, so the error return code -EINVAL may be incorrectly set
to 0. To fix set valid return code before calling to goto.
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: b993f8e696ba ("ARM: mvebu: add Device Tree files for Armada 39x SoC and board") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: eb972d1b1a01 ("ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 467d0a0a3826 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 648941be368e ("arm: mvebu: add PCIe Device Tree informations for Armada XP") Fixes: 0ea1593b6db8 ("ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable") Fixes: f344251f1bd3 ("ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
Fixes: 91e027ea851d ("arm: mvebu: add PCIe Device Tree informations for Armada 370") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BDF of resource in DT assigned-addresses property of Marvell PCIe Root Port
(PCI-to-PCI bridge) should match BDF in address part in that DT node name
as specified resource belongs to Marvell PCIe Root Port itself.
The unit address for the pinctrl node is (0x)1000b000 and not
(0x)10005000, which is the syscfg_pctl_a address instead.
This fixes the following warning:
arch/arm64/boot/dts/mediatek/mt2712e.dtsi:264.40-267.4: Warning
(unique_unit_address): /syscfg_pctl_a@10005000: duplicate
unit-address (also used in node /pinctrl@10005000)
arm_smmu_pmu_init() won't remove the callback added by
cpuhp_setup_state_multi() when platform_driver_register() failed. Remove
the callback by cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit af0a3a3c6a96 ("bus:
arm-ccn: Prevent hotplug callback leak")
dsu_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit af0a3a3c6a96 ("bus:
arm-ccn: Prevent hotplug callback leak")
Fixes: ab287d045d62 ("perf: ARM DynamIQ Shared Unit PMU support") Signed-off-by: Yuan Can <yuancan@huawei.com> Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20221115070207.32634-2-yuancan@huawei.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
The checks for musb->xceiv and musb->xceiv->set_power duplicate those in
usb_phy_set_power(), so there is no need of them. Moreover, not calling
usb_phy_set_power() results in usb_phy_set_charger_current() not being
called, so current USB config max current is not propagated through USB
charger framework and charger drivers may try to draw more current than
allowed or possible.
Fix that by removing those extra checks and calling usb_phy_set_power()
directly.
When the name_assign_type attribute was introduced (commit 2e95b1c941e6, "net: add name_assign_type netdev attribute"), the
loopback device was explicitly mentioned as one which would make use
of NET_NAME_PREDICTABLE:
The name_assign_type attribute gives hints where the interface name of a
given net-device comes from. These values are currently defined:
...
NET_NAME_PREDICTABLE:
The ifname has been assigned by the kernel in a predictable way
that is guaranteed to avoid reuse and always be the same for a
given device. Examples include statically created devices like
the loopback device [...]
Switch to that so that reading /sys/class/net/lo/name_assign_type
produces something sensible instead of returning -EINVAL.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
By keep sending L2CAP_CONF_REQ packets, chan->num_conf_rsp increases
multiple times and eventually it will wrap around the maximum number
(i.e., 255).
This patch prevents this by adding a boundary check with
L2CAP_MAX_CONF_RSP
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Acer Aspire Switch 10E (SW3-016)'s keyboard-dock uses the same USB-ids
as the Acer One S1003 keyboard-dock. Yet they are not entirely the same:
1. The S1003 keyboard-dock has the same report descriptors as the
S1002 keyboard-dock (which has different USB-ids)
2. The Acer Aspire Switch 10E's keyboard-dock has different
report descriptors from the S1002/S1003 keyboard docks and it
sends 0x00880078 / 0x00880079 usage events when the touchpad is
toggled on/off (which is handled internally).
This means that all Acer kbd-docks handled by the hid-ite.c drivers
report their touchpad being toggled on/off through these custom
usage-codes with the exception of the S1003 dock, which likely is
a bug of that dock.
Add a QUIRK_TOUCHPAD_ON_OFF_REPORT quirk for the Aspire Switch 10E / S1003
usb-id so that the touchpad toggling will get reported to userspace on
the Aspire Switch 10E.
Since the Aspire Switch 10E's kbd-dock has different report-descriptors,
this also requires adding support for fixing those to ite_report_fixup().
Setting the quirk will also cause ite_report_fixup() to hit the
S1002/S1003 descriptors path on the S1003. Since the S1003 kbd-dock
never generates any input-reports for the fixed up part of the
descriptors this does not matter; and if there are versions out there
which do actually send input-reports for the touchpad-toggle then the
fixup should actually help to make things work.
This was tested on both an Acer Aspire Switch 10E and on an Acer One S1003.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stable-dep-of: 8f04554b1c08 ("HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10") Signed-off-by: Sasha Levin <sashal@kernel.org>
Make the hid-ite driver handle the Acer S1002 keyboard-dock, this
leads to 2 improvements:
1. The non working wifi-toggle hotkey now works.
2. Toggling the touchpad on of with the hotkey will no show OSD
notifications in e.g. GNOME3. The actual toggling is handled inside
the keyboard, this adds support for notifying evdev listeners about this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stable-dep-of: 8f04554b1c08 ("HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10") Signed-off-by: Sasha Levin <sashal@kernel.org>
Pratyush Yadav [Mon, 19 Dec 2022 15:37:10 +0000 (16:37 +0100)]
xen-netback: move removal of "hotplug-status" to the right place
The removal of "hotplug-status" has moved around a bit. First it was
moved from netback_remove() to hotplug_status_changed() in upstream
commit ee7e4850fad9 ("xen-netback: remove 'hotplug-status' once it has
served its purpose"). Then the change was reverted in upstream commit 19d2f790e4d2 ("Revert "xen-netback: remove 'hotplug-status' once it has
served its purpose""), but it moved the removal to backend_disconnect().
Then the upstream commit 56ad827fa9ca ("xen-netback: only remove
'hotplug-status' when the vif is actually destroyed") moved it finally
back to netback_remove(). The thing to note being it is removed
unconditionally this time around.
The story on v5.4.y adds to this confusion. Commit 1cef550f59ad ("Revert
"xen-netback: remove 'hotplug-status' once it has served its purpose"")
is backported to v5.4.y but the original commit that it tries to revert
was never present on 5.4. So the backport incorrectly ends up just
adding another xenbus_rm() of "hotplug-status" in backend_disconnect().
Now in v5.4.y it is removed in both backend_disconnect() and
netback_remove(). But it should only be removed in netback_remove(), as
the upstream version does.
Removing "hotplug-status" in backend_disconnect() causes problems when
the frontend unilaterally disconnects, as explained in 56ad827fa9ca ("xen-netback: only remove 'hotplug-status' when the vif is
actually destroyed").
Remove "hotplug-status" in the same place as it is done on the upstream
version to ensure unilateral re-connection of frontend continues to
work.
Fixes: 1cef550f59ad ("Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"") Signed-off-by: Pratyush Yadav <ptyadav@amazon.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a MAC address is not assigned to the VF, that portion of the message
sent to the VF is not set. The memory, however, is allocated from the
stack meaning that information may be leaked to the VM. Initialize the
message buffer to 0 so that no information is passed to the VM in this
case.
Fixes: fcfd658ab088 ("igb: Indicate failure on vf reset for empty mac address") Reported-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221212190031.3983342-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
Setup function uvc_function_setup permits control transfer
requests with up to 64 bytes of payload (UVC_MAX_REQUEST_SIZE),
data stage handler for OUT transfer uses memcpy to copy req->actual
bytes to uvc_event->data.data array of size 60. This may result
in an overflow of 4 bytes.
Fixes: 1223a1eb5b1f ("USB gadget: video class function driver") Cc: stable <stable@kernel.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com> Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com> Link: https://lore.kernel.org/r/20221206141301.51305-1-szymon.heidrich@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extending file within last block it can happen that the extent is
already rounded to the blocksize and thus contains the offset we want to
grow up to. In such case we would mistakenly expand the last extent and
make it one block longer than it should be, exposing unallocated block
in a file and causing data corruption. Fix the problem by properly
detecting this case and bailing out.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When preallocation extent is the first one in the extent block, the
code would corrupt extent tree header instead. Fix the problem and use
udf_delete_aext() for deleting extent to avoid some code duplication.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When extending file with a hole, we tried to preserve existing
preallocation for the file. However that is not very useful and
complicates code because the previous extent may need to be rounded to
block boundary as well (which we forgot to do thus causing data
corruption for sequence like:
Pratyush Yadav [Fri, 16 Dec 2022 13:42:41 +0000 (14:42 +0100)]
tracing/ring-buffer: Only do full wait when cpu != RING_BUFFER_ALL_CPUS
full_hit() directly uses cpu as an array index. Since
RING_BUFFER_ALL_CPUS == -1, calling full_hit() with cpu ==
RING_BUFFER_ALL_CPUS will cause an invalid memory access.
The upstream commit bf7966d96b74 ("tracing/ring-buffer: Have polling
block on watermark") already does this. This was missed when backporting
to v5.4.y.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 9b7faceb5367 ("tracing/ring-buffer: Have polling block on watermark") Signed-off-by: Pratyush Yadav <ptyadav@amazon.de> Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the check against the max value for the control is being
applied after the value has had the minimum applied and been masked. But
the max value simply indicates the number of volume levels on an SX
control, and as such should just be applied on the raw value.
Fixes: ca218ac85398 ("ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20221125162348.1288005-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've observed, both with my oscilloscope and captured USB packets
below, you must send "0" to turn it ON, and "1" to turn it OFF.
From the schematics in the user's guide, I can confirm that you must
drive the CAN_RES signal LOW "0" to activate the resistors.
Reverse the argument value of usb_msg.termination to fix this.
These are the two commands sequence, ON then OFF.
> No. Time Source Destination Protocol Length Info
> 1 0.000000 host 1.3.1 USB 46 URB_BULK out
>
> Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80000000000000000000000000000000000a8
>
> No. Time Source Destination Protocol Length Info
> 2 4.372547 host 1.3.1 USB 46 URB_BULK out
>
> Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80100000000000000000000000000000000a9
The bounds checks in snd_soc_put_volsw_sx() are only being applied to the
first channel, meaning it is possible to write out of bounds values to the
second channel in stereo controls. Add appropriate checks.
area_cache_get() is used to distribute cache->area and set cache->id,
and if cache->id is not 0 and cache->area->kref refcount is 0, it will
release the cache->area by nfp_cpp_area_release(). area_cache_get()
set cache->id before cpp->op->area_init() and nfp_cpp_area_acquire().
But if area_init() or nfp_cpp_area_acquire() fails, the cache->id is
is already set but the refcount is not increased as expected. At this
time, calling the nfp_cpp_area_release() will cause use-after-free.
To avoid the use-after-free, set cache->id after area_init() and
nfp_cpp_area_acquire() complete successfully.
Note: This vulnerability is triggerable by providing emulated device
equipped with specified configuration.
BUG: KASAN: use-after-free in nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
Write of size 4 at addr ffff888005b7f4a0 by task swapper/0/1
Ming Lei [Tue, 13 Dec 2022 07:16:03 +0000 (15:16 +0800)]
block: unhash blkdev part inode when the part is deleted
v5.11 changes the blkdev lookup mechanism completely since commit 0f711687d915 ("block: simplify bdev/disk lookup in blkdev_get"),
and small part of the change is to unhash part bdev inode when
deleting partition. Turns out this kind of change does fix one
nasty issue in case of BLOCK_EXT_MAJOR:
1) when one partition is deleted & closed, disk_put_part() is always
called before bdput(bdev), see blkdev_put(); so the part's devt can
be freed & re-used before the inode is dropped
2) then new partition with same devt can be created just before the
inode in 1) is dropped, then the old inode/bdev structurein 1) is
re-used for this new partition, this way causes use-after-free and
kernel panic.
It isn't possible to backport the whole big patchset of "merge struct
block_device and struct hd_struct v4" for addressing this issue.
So fixes it by unhashing part bdev in delete_partition(), and this way
is actually aligned with v5.11+'s behavior.
Backported from the following 5.10.y commit:
5f2f77560591 ("block: unhash blkdev part inode when the part is deleted")
Reported-by: Shiwei Cui <cuishw@inspur.com> Tested-by: Shiwei Cui <cuishw@inspur.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some architectures (like ARM64), it can support CONT-PTE/PMD size
hugetlb, which means it can support not only PMD/PUD size hugetlb (2M and
1G), but also CONT-PTE/PMD size(64K and 32M) if a 4K page size specified.
So when looking up a CONT-PTE size hugetlb page by follow_page(), it will
use pte_offset_map_lock() to get the pte entry lock for the CONT-PTE size
hugetlb in follow_page_pte(). However this pte entry lock is incorrect
for the CONT-PTE size hugetlb, since we should use huge_pte_lock() to get
the correct lock, which is mm->page_table_lock.
That means the pte entry of the CONT-PTE size hugetlb under current pte
lock is unstable in follow_page_pte(), we can continue to migrate or
poison the pte entry of the CONT-PTE size hugetlb, which can cause some
potential race issues, even though they are under the 'pte lock'.
For example, suppose thread A is trying to look up a CONT-PTE size hugetlb
page by move_pages() syscall under the lock, however antoher thread B can
migrate the CONT-PTE hugetlb page at the same time, which will cause
thread A to get an incorrect page, if thread A also wants to do page
migration, then data inconsistency error occurs.
Moreover we have the same issue for CONT-PMD size hugetlb in
follow_huge_pmd().
To fix above issues, rename the follow_huge_pmd() as follow_huge_pmd_pte()
to handle PMD and PTE level size hugetlb, which uses huge_pte_lock() to
get the correct pte entry lock to make the pte entry stable.
Mike said:
Support for CONT_PMD/_PTE was added with 939050df9a5c ("arm64: hugetlb:
refactor find_num_contig()"). Patch series "Support for contiguous pte
hugepages", v4. However, I do not believe these code paths were
executed until migration support was added with fb22f5e9b6f9 ("arm64/mm:
enable HugeTLB migration for contiguous bit HugeTLB pages") I would go
with fb22f5e9b6f9 for the Fixes: targe.
Link: https://lkml.kernel.org/r/635f43bdd85ac2615a58405da82b4d33c6e5eb05.1662017562.git.baolin.wang@linux.alibaba.com Fixes: fb22f5e9b6f9 ("arm64/mm: enable HugeTLB migration for contiguous bit HugeTLB pages") Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com> Suggested-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: David Hildenbrand <david@redhat.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[5.4: Fixup contextual diffs before pin_user_pages()] Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is avoided by moving the call to rcu_cpu_starting up near
the beginning of the start_secondary() function. Note that the
raw_smp_processor_id() is required in order to avoid calling into lockdep
before RCU has declared the CPU to be watched for readers.
Link: https://lore.kernel.org/lkml/160223032121.7002.1269740091547117869.tip-bot2@tip-bot2/ Reported-by: Qian Cai <cai@redhat.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Cc: Joel Fernandes <joel@joelfernandes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows TC eBPF programs to modify and forward (redirect) packets
from interfaces without ethernet headers (for example cellular)
to interfaces with (for example ethernet/wifi).
The lack of this appears to simply be an oversight.
Tested:
in active use in Android R on 4.14+ devices for ipv6
cellular to wifi tethering offload.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't get any further EVENT from an esd CAN USB device for changes
on REC or TEC while those counters converge to 0 (with ecc == 0). So
when handling the "Back to Error Active"-event force txerr = rxerr =
0, otherwise the berr-counters might stay on values like 95 forever.
Also, to make life easier during the ongoing development a
netdev_dbg() has been introduced to allow dumping error events send by
an esd CAN USB device.
Fixes: 37ca9589408a ("can: Add driver for esd CAN-USB/2 device") Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu> Link: https://lore.kernel.org/all/20221130202242.3998219-2-frank.jungclaus@esd.eu Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In an earlier commit, I added a bounds check to prevent an out of bounds
read and a WARN(). On further discussion and consideration that check
was probably too aggressive. Instead of returning -EINVAL, a better fix
would be to just prevent the out of bounds read but continue the process.
Background: The value of "pp->rxq_def" is a number between 0-7 by default,
or even higher depending on the value of "rxq_number", which is a module
parameter. If the value is more than the number of available CPUs then
it will trigger the WARN() in cpu_max_bits_warn().
Fixes: e8b4fc13900b ("net: mvneta: Prevent out of bounds read in mvneta_config_rss()") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/Y5A7d1E5ccwHTYPf@kadam Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Blamed commit claimed rcu_read_lock() was held by ip6_fragment() callers.
It seems to not be always true, at least for UDP stack.
syzbot reported:
BUG: KASAN: use-after-free in ip6_dst_idev include/net/ip6_fib.h:245 [inline]
BUG: KASAN: use-after-free in ip6_fragment+0x2724/0x2770 net/ipv6/ip6_output.c:951
Read of size 8 at addr ffff88801d403e80 by task syz-executor.3/7618
The buggy address belongs to the object at ffff88801d403dc0
which belongs to the cache ip6_dst_cache of size 240
The buggy address is located 192 bytes inside of
240-byte region [ffff88801d403dc0, ffff88801d403eb0)
It is not allowed to call kfree_skb() or consume_skb() from
hardware interrupt context or with interrupts being disabled.
So replace kfree_skb/dev_kfree_skb() with dev_kfree_skb_irq()
and dev_consume_skb_irq() under spin_lock_irq().
Commit ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in
the non-linear area") introduced a (valid) build warning. There have
even been reports of this problem breaking networking of Xen guests.
Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cited commit added the table ID to the FIB info structure, but did not
properly initialize it when table ID 0 is used. This can lead to a route
in the default VRF with a preferred source address not being flushed
when the address is deleted.
Consider the following example:
# ip address add dev dummy1 192.0.2.1/28
# ip address add dev dummy1 192.0.2.17/28
# ip route add 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 100
# ip route add table 0 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 200
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 100
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200
Both routes are installed in the default VRF, but they are using two
different FIB info structures. One with a metric of 100 and table ID of
254 (main) and one with a metric of 200 and table ID of 0. Therefore,
when the preferred source address is deleted from the default VRF,
the second route is not flushed:
# ip address del dev dummy1 192.0.2.17/28
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200
Fix by storing a table ID of 254 instead of 0 in the route configuration
structure.
Add a test case that fails before the fix:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Table ID 0
TEST: Route removed in default VRF when source address deleted [FAIL]
Tests passed: 8
Tests failed: 1
And passes after:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Table ID 0
TEST: Route removed in default VRF when source address deleted [ OK ]
Tests passed: 9
Tests failed: 0
Fixes: 0b000b29c23b ("net: Don't delete routes in different VRFs") Reported-by: Donald Sharp <sharpd@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cited commit added the table ID to the FIB info structure, but did not
prevent structures with different table IDs from being consolidated.
This can lead to routes being flushed from a VRF when an address is
deleted from a different VRF.
Fix by taking the table ID into account when looking for a matching FIB
info. This is already done for FIB info structures backed by a nexthop
object in fib_find_info_nh().
Add test cases that fail before the fix:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [FAIL]
TEST: Route in default VRF not removed [ OK ]
RTNETLINK answers: File exists
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [FAIL]
Tests passed: 6
Tests failed: 2
And pass after:
# ./fib_tests.sh -t ipv4_del_addr
IPv4 delete address route tests
Regular FIB info
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Identical FIB info with different table ID
TEST: Route removed from VRF when source address deleted [ OK ]
TEST: Route in default VRF not removed [ OK ]
TEST: Route removed in default VRF when source address deleted [ OK ]
TEST: Route in VRF is not removed by address delete [ OK ]
Tests passed: 8
Tests failed: 0
Fixes: 0b000b29c23b ("net: Don't delete routes in different VRFs") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nicvf_probe() won't destroy workqueue when register_netdev()
failed. Add destroy_workqueue err handle case to fix this issue.
Fixes: 50ef047b1ed9 ("net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them.") Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20221203094125.602812-1-liuyongqiang13@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dt-binding snps,dwmac.yaml, some properties under "snps,axi-config"
node are named without "axi_" prefix, but the driver expects the
prefix. Since the dt-binding has been there for a long time, we'd
better make driver match the binding for compatibility.
Fixes: 99942d2abc37 ("stmmac: rework DMA bus setting and introduce new platform AXI structure") Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Link: https://lore.kernel.org/r/20221202161739.2203-1-jszhang@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A device might have a core quirk for NVME_QUIRK_IGNORE_DEV_SUBNQN
(such as Samsung X5) but it would still give a:
"missing or invalid SUBNQN field"
warning as core quirks are filled after calling nvme_init_subnqn. Fill
ctrl->quirks from struct core_quirks before calling nvme_init_subsystem
to fix this.
Return -EOPNOTSUPP, when user requests l4_4_bytes for raw IP4 or
IP6 flow director filters. Flow director does not support filtering
on l4 bytes for PCTYPEs used by IP4 and IP6 filters.
Without this patch, user could create filters with l4_4_bytes fields,
which did not do any filtering on L4, but only on L3 fields.
Fixes: 482b43e50562 ("i40e: check current configured input set when adding ntuple filters") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After spawning max VFs on a PF, some VFs were not getting resources and
their MAC addresses were 0. This was caused by PF sleeping before flushing
HW registers which caused VIRTCHNL_VFR_VFACTIVE to not be set in time for
VF.
Fix by adding a sleep after hw flush.
Fixes: 88d48b20c639 ("i40e: reset all VFs in parallel when rebuilding PF") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During tx rings configuration default XPS queue config is set and
__I40E_TX_XPS_INIT_DONE is locked. __I40E_TX_XPS_INIT_DONE state is
cleared and set again with default mapping only during queues build,
it means after first setup or reset with queues rebuild. (i.e.
ethtool -L <interface> combined <number>) After other resets (i.e.
ethtool -t <interface>) XPS_INIT_DONE is not cleared and those default
maps cannot be set again. It results in cleared xps_cpus mapping
until queues are not rebuild or mapping is not set by user.
Add clearing __I40E_TX_XPS_INIT_DONE state during reset to let
the driver set xps_cpus to defaults again after it was cleared.
Fixes: 111ff146641f ("i40e: allow XPS with QoS enabled") Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pp->indir[0] value comes from the user. It is passed to:
if (cpu_online(pp->rxq_def))
inside the mvneta_percpu_elect() function. It needs bounds checkeding
to ensure that it is not beyond the end of the cpu bitmap.
Fixes: 4e84c9e82f5d ("net: mvneta: Fix the CPU choice in mvneta_percpu_elect") Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A NAPI is setup for each network sring to poll data to kernel
The sring with source host is destroyed before live migration and
new sring with target host is setup after live migration.
The NAPI for the old sring is not deleted until setup new sring
with target host after migration. With busy_poll/busy_read enabled,
the NAPI can be polled before got deleted when resume VM.
xen frontend should remove the NAPIs for the old srings before live
migration as the bond srings are destroyed
There is a tiny window between the srings are set to NULL and
the NAPIs are disabled, It is safe as the NAPI threads are still
frozen at that time
Signed-off-by: Lin Liu <lin.liu@citrix.com> Fixes: 5914bf9131ee ([NET]: Do not check netif_running() and carrier state in ->poll()) Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In functions regmap_encx24j600_phy_reg_read() and
regmap_encx24j600_phy_reg_write() in the conditions of the waiting
cycles for filling the variable 'ret' it is necessary to add parentheses
to prevent wrong assignment due to logical operations precedence.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2b27d5f85455 ("net: Microchip encx24j600 driver") Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ieee802154_if_add() allocates wpan_dev as netdev's private data, but not
init the list in struct wpan_dev. cfg802154_netdev_notifier_call() manage
the list when device register/unregister, and may lead to null-ptr-deref.
Use INIT_LIST_HEAD() on it to initialize it correctly.
When testing in kci_test_ipsec_offload, srcip is configured as $dstip,
it should add xfrm policy rule in instead of out.
The test result of this patch is as follows:
PASS: ipsec_offload
Fixes: 25d87e7abc0f ("selftests: rtnetlink: add ipsec offload API test") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Acked-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20221201082246.14131-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Wei Chen reported a NULL deref in sk_user_ns() [0][1], and Paolo diagnosed
the root cause: in unix_diag_get_exact(), the newly allocated skb does not
have sk. [2]
We must get the user_ns from the NETLINK_CB(in_skb).sk and pass it to
sk_diag_fill().
Without this change, the interrupt test fail with MSI-X environment:
$ sudo ethtool -t enp0s2 offline
[ 43.921783] igb 0000:00:02.0: offline testing starting
[ 44.855824] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Down
[ 44.961249] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 51.272202] igb 0000:00:02.0: testing shared interrupt
[ 56.996975] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 4
Loopback test (offline) 0
Link test (on/offline) 0
Here, "4" means an expected interrupt was not delivered.
To fix this, route IRQs correctly to the first MSI-X vector by setting
IVAR_MISC. Also, set bit 0 of EIMS so that the vector will not be
masked. The interrupt test now runs properly with this change:
$ sudo ethtool -t enp0s2 offline
[ 42.762985] igb 0000:00:02.0: offline testing starting
[ 50.141967] igb 0000:00:02.0: testing shared interrupt
[ 56.163957] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Fixes: 38ab6c37e85e ("igb: add single vector msi-x testing to interrupt test") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.
This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
```
/* reserve a descriptor for the offload context */
if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
count++;
count++;
This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```
Fixes: 3f32e81cc0ea ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: 0215c02983ce ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the description in ti-sn65dsi86's datasheet:
CHA_HSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
CHA_VSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (Default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
We should only set these bits when the polarity is negative.
Fixes: 75a27075bea1 ("drm/bridge: add support for sn65dsi86 bridge driver") Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221125104558.84616-1-eddy.zhang@rock-chips.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct cas_control embeds multiple generic SPI structures and we
have to make sure these structures are initialized to default values.
This driver does not set all attributes. When using kmalloc before some
attributes were not initialized and contained random data which caused
random crashes at bootup.
Analogue to commit 16d6a19398a6 ("can: af_can: fix NULL pointer
dereference in can_rx_register()") we need to check for a missing
initialization of ml_priv in the receive path of CAN frames.
Since commit 82817a015495 ("net: introduce CAN specific pointer in the
struct net_device") the check for dev->type to be ARPHRD_CAN is not
sufficient anymore since bonding or tun netdevices claim to be CAN
devices but do not initialize ml_priv accordingly.
Fixes: 82817a015495 ("net: introduce CAN specific pointer in the struct net_device") Reported-by: syzbot+2d7f58292cb5b29eb5ad@syzkaller.appspotmail.com Reported-by: Wei Chen <harperchen1110@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20221206201259.3028-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported shift-out-of-bounds in hid_report_raw_event.
microsoft 0003:045E:07DA.0001: hid_field_extract() called with n (128) >
32! (swapper/0)
======================================================================
UBSAN: shift-out-of-bounds in drivers/hid/hid-core.c:1323:20
shift exponent 127 is too large for 32-bit type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rc4-syzkaller-00159-g4bbf3422df78 #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS
Google 10/26/2022
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e3/0x2cb lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x3a6/0x420 lib/ubsan.c:322
snto32 drivers/hid/hid-core.c:1323 [inline]
hid_input_fetch_field drivers/hid/hid-core.c:1572 [inline]
hid_process_report drivers/hid/hid-core.c:1665 [inline]
hid_report_raw_event+0xd56/0x18b0 drivers/hid/hid-core.c:1998
hid_input_report+0x408/0x4f0 drivers/hid/hid-core.c:2066
hid_irq_in+0x459/0x690 drivers/hid/usbhid/hid-core.c:284
__usb_hcd_giveback_urb+0x369/0x530 drivers/usb/core/hcd.c:1671
dummy_timer+0x86b/0x3110 drivers/usb/gadget/udc/dummy_hcd.c:1988
call_timer_fn+0xf5/0x210 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers+0x76a/0x980 kernel/time/timer.c:1790
run_timer_softirq+0x63/0xf0 kernel/time/timer.c:1803
__do_softirq+0x277/0x75b kernel/softirq.c:571
__irq_exit_rcu+0xec/0x170 kernel/softirq.c:650
irq_exit_rcu+0x5/0x20 kernel/softirq.c:662
sysvec_apic_timer_interrupt+0x91/0xb0 arch/x86/kernel/apic/apic.c:1107
======================================================================
If the size of the integer (unsigned n) is bigger than 32 in snto32(),
shift exponent will be too large for 32-bit type 'int', resulting in a
shift-out-of-bounds bug.
Fix this by adding a check on the size of the integer (unsigned n) in
snto32(). To add support for n greater than 32 bits, set n to 32, if n
is greater than 32.
projects / kernel.git / log