Linus Torvalds [Sat, 21 Aug 2021 17:50:22 +0000 (10:50 -0700)]
Merge tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull mandatory file locking deprecation warning from Jeff Layton:
"As discussed on the list, this patch just adds a new warning for folks
who still have mandatory locking enabled and actually mount with '-o
mand'. I'd like to get this in for v5.14 so we can push this out into
stable kernels and hopefully reach folks who have mounts with -o mand.
For now, I'm operating under the assumption that we'll fully remove
this support in v5.15, but we can move that out if any legitimate
users of this facility speak up between now and then"
* tag 'locks-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
fs: warn about impending deprecation of mandatory locks
Linus Torvalds [Sat, 21 Aug 2021 15:11:22 +0000 (08:11 -0700)]
Merge tag 'block-5.14-2021-08-20' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Three fixes from Ming Lei that should go into 5.14:
- Fix for a kernel panic when iterating over tags for some cases
where a flush request is present, a regression in this cycle.
- Request timeout fix
- Fix flush request checking"
* tag 'block-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
blk-mq: fix is_flush_rq
blk-mq: fix kernel panic during iterating over flush request
blk-mq: don't grab rq's refcount in blk_mq_check_expired()
Linus Torvalds [Sat, 21 Aug 2021 15:06:26 +0000 (08:06 -0700)]
Merge tag 'io_uring-5.14-2021-08-20' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few small fixes that should go into this release:
- Fix never re-assigning an initial error value for io_uring_enter()
for SQPOLL, if asked to do nothing
- Fix xa_alloc_cycle() return value checking, for cases where we have
wrapped around
- Fix for a ctx pin issue introduced in this cycle (Pavel)"
* tag 'io_uring-5.14-2021-08-20' of git://git.kernel.dk/linux-block:
io_uring: fix xa_alloc_cycle() error return value check
io_uring: pin ctx on fallback execution
io_uring: only assign io_uring_enter() SQPOLL error in actual error case
Jeff Layton [Fri, 20 Aug 2021 13:29:50 +0000 (09:29 -0400)]
fs: warn about impending deprecation of mandatory locks
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org>
Jens Axboe [Fri, 20 Aug 2021 20:53:59 +0000 (14:53 -0600)]
io_uring: fix xa_alloc_cycle() error return value check
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
Linus Torvalds [Fri, 20 Aug 2021 20:44:25 +0000 (13:44 -0700)]
Merge tag 'acpi-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two mistakes in new code.
Specifics:
- Prevent confusing messages from being printed if the PRMT table is
not present or there are no PRM modules (Aubrey Li).
- Fix the handling of suspend-to-idle entry and exit in the case when
the Microsoft UUID is used with the Low-Power S0 Idle _DSM
interface (Mario Limonciello)"
* tag 'acpi-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Invert Microsoft UUID entry and exit
ACPI: PRM: Deal with table not present or no module found
Linus Torvalds [Fri, 20 Aug 2021 20:38:42 +0000 (13:38 -0700)]
Merge tag 'pm-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix some issues in the ARM cpufreq drivers and in the operating
performance points (OPP) framework.
Specifics:
- Fix useless WARN() in the OPP core and prevent a noisy warning
from being printed by OPP _put functions (Dmitry Osipenko).
- Fix error path when allocation failed in the arm_scmi cpufreq
driver (Lukasz Luba).
- Blacklist Qualcomm sc8180x and Qualcomm sm8150 in
cpufreq-dt-platdev (Bjorn Andersson, Thara Gopinath).
- Forbid cpufreq for 1.2 GHz variant in the armada-37xx cpufreq
driver (Marek Behún)"
* tag 'pm-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Drop empty-table checks from _put functions
cpufreq: armada-37xx: forbid cpufreq for 1.2 GHz variant
cpufreq: blocklist Qualcomm sm8150 in cpufreq-dt-platdev
cpufreq: arm_scmi: Fix error path when allocation failed
opp: remove WARN when no valid OPPs remain
cpufreq: blacklist Qualcomm sc8180x in cpufreq-dt-platdev
Linus Torvalds [Fri, 20 Aug 2021 19:59:54 +0000 (12:59 -0700)]
Merge tag 'drm-fixes-2021-08-20-3' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regularly scheduled fixes. The ttm one solves a problem of GPU drivers
failing to load if debugfs is off in Kconfig, otherwise the i915 and
mediatek, and amdgpu fixes all fairly normal.
Nouveau has a couple of display fixes, but it has a fix for a
longstanding race condition in it's memory manager code, and the fix
mostly removes some code that wasn't working properly and has no
userspace users. This fix makes the diffstat kinda larger but in a
good (negative line-count) way.
* tag 'drm-fixes-2021-08-20-3' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Use DCN30 watermark calc for DCN301
drm/i915/dp: remove superfluous EXPORT_SYMBOL()
drm/i915/edp: fix eDP MSO pipe sanity checks for ADL-P
drm/i915: Tweaked Wa_14010685332 for all PCHs
drm/nouveau: rip out nvkm_client.super
drm/nouveau: block a bunch of classes from userspace
drm/nouveau/fifo/nv50-: rip out dma channels
drm/nouveau/kms/nv50: workaround EFI GOP window channel format differences
drm/nouveau/disp: power down unused DP links during init
drm/nouveau: recognise GA107
drm: Copy drm_wait_vblank to user before returning
drm/amd/display: Ensure DCN save after VM setup
drm/amdkfd: fix random KFDSVMRangeTest.SetGetAttributesTest test failure
drm/amd/pm: change the workload type for some cards
Revert "drm/amd/pm: fix workload mismatch on vega10"
drm: ttm: Don't bail from ttm_global_init if debugfs_create_dir fails
drm/mediatek: Add component_del in OVL and COLOR remove function
drm/mediatek: Add AAL output size configuration
- Add Jim Quinlan et al as Broadcom STB PCIe maintainers (Jim Quinlan)
- Increase D3hot-to-D0 delay for AMD Renoir/Cezanne XHCI (Marcin
Bachry)
- Correct iomem_get_mapping() usage for legacy_mem sysfs (Krzysztof
Wilczyński)
* tag 'pci-v5.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/sysfs: Use correct variable for the legacy_mem sysfs object
PCI: Increase D3 delay for AMD Renoir/Cezanne XHCI
MAINTAINERS: Add Jim Quinlan et al as Broadcom STB PCIe maintainers
MAINTAINERS: Add Rahul Tanwar as Intel LGM Gateway PCIe maintainer
Linus Torvalds [Fri, 20 Aug 2021 19:46:00 +0000 (12:46 -0700)]
Merge tag 'mmc-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- dw_mmc: Fix hang on data CRC error
- mmci: Fix voltage switch procedure for the stm32 variant
- sdhci-iproc: Fix some clock issues for BCM2711
- sdhci-msm: Fixup software timeout value
* tag 'mmc-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711
mmc: sdhci-iproc: Cap min clock frequency on BCM2711
mmc: sdhci-msm: Update the software timeout value for sdhc
mmc: mmci: stm32: Check when the voltage switch procedure should be done
mmc: dw_mmc: Fix hang on data CRC error
Linus Torvalds [Fri, 20 Aug 2021 19:31:10 +0000 (12:31 -0700)]
Merge tag 'sound-5.14-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"This is a quick follow up for 5.14: a fix for a very recently
introduced regression on ASoC Intel Atom driver, and another trivial
HD-audio quirk for HP laptops"
* tag 'sound-5.14-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: intel: atom: Fix breakage for PCM buffer address setup
ALSA: hda/realtek: Limit mic boost on HP ProBook 445 G8
Linus Torvalds [Fri, 20 Aug 2021 19:18:49 +0000 (12:18 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix cleaning of vDSO directories
- Ensure CNTHCTL_EL2 is fully initialised when booting at EL2
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: initialize all of CNTHCTL_EL2
arm64: clean vdso & vdso32 files
Linus Torvalds [Fri, 20 Aug 2021 19:11:33 +0000 (12:11 -0700)]
Merge tag 'iommu-fixes-v5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix for a potential NULL-ptr dereference in IOMMU core code
- Two resource leak fixes
- Cache flush fix in the Intel VT-d driver
* tag 'iommu-fixes-v5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix incomplete cache flush in intel_pasid_tear_down_entry()
iommu/vt-d: Fix PASID reference leak
iommu: Check if group is NULL before remove device
iommu/dma: Fix leak in non-contiguous API
Mike Kravetz [Fri, 20 Aug 2021 02:04:33 +0000 (19:04 -0700)]
hugetlb: don't pass page cache pages to restore_reserve_on_error
syzbot hit kernel BUG at fs/hugetlbfs/inode.c:532 as described in [1].
This BUG triggers if the HPageRestoreReserve flag is set on a page in
the page cache. It should never be set, as the routine
huge_add_to_page_cache explicitly clears the flag after adding a page to
the cache.
The only code other than huge page allocation which sets the flag is
restore_reserve_on_error. It will potentially set the flag in rare out
of memory conditions. syzbot was injecting errors to cause memory
allocation errors which exercised this specific path.
The code in restore_reserve_on_error is doing the right thing. However,
there are instances where pages in the page cache were being passed to
restore_reserve_on_error. This is incorrect, as once a page goes into
the cache reservation information will not be modified for the page
until it is removed from the cache. Error paths do not remove pages
from the cache, so even in the case of error, the page will remain in
the cache and no reservation adjustment is needed.
Modify routines that potentially call restore_reserve_on_error with a
page cache page to no longer do so.
Note on fixes tag: Prior to commit 846be08578ed ("mm/hugetlb: expand
restore_reserve_on_error functionality") the routine would not process
page cache pages because the HPageRestoreReserve flag is not set on such
pages. Therefore, this issue could not be trigggered. The code added
by commit 846be08578ed ("mm/hugetlb: expand restore_reserve_on_error
functionality") is needed and correct. It exposed incorrect calls to
restore_reserve_on_error which is the root cause addressed by this
commit.
Marco Elver [Fri, 20 Aug 2021 02:04:30 +0000 (19:04 -0700)]
kfence: fix is_kfence_address() for addresses below KFENCE_POOL_SIZE
Originally the addr != NULL check was meant to take care of the case
where __kfence_pool == NULL (KFENCE is disabled). However, this does
not work for addresses where addr > 0 && addr < KFENCE_POOL_SIZE.
This can be the case on NULL-deref where addr > 0 && addr < PAGE_SIZE or
any other faulting access with addr < KFENCE_POOL_SIZE. While the
kernel would likely crash, the stack traces and report might be
confusing due to double faults upon KFENCE's attempt to unprotect such
an address.
Fix it by just checking that __kfence_pool != NULL instead.
Link: https://lkml.kernel.org/r/20210818130300.2482437-1-elver@google.com Fixes: 0ce20dd84089 ("mm: add Kernel Electric-Fence infrastructure") Signed-off-by: Marco Elver <elver@google.com> Reported-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com> Acked-by: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> [5.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 20 Aug 2021 02:04:27 +0000 (19:04 -0700)]
mm: vmscan: fix missing psi annotation for node_reclaim()
In a debugging session the other day, Rik noticed that node_reclaim()
was missing memstall annotations. This means we'll miss pressure and
lost productivity resulting from reclaim on an overloaded local NUMA
node when vm.zone_reclaim_mode is enabled.
There haven't been any reports, but that's likely because
vm.zone_reclaim_mode hasn't been a commonly used feature recently, and
the intersection between such setups and psi users is probably nil.
But secondary memory such as CXL-connected DIMMS, persistent memory etc,
and the page demotion patches that handle them
(https://lore.kernel.org/lkml/20210401183216.443C4443@viggo.jf.intel.com/)
could soon make this a more common codepath again.
Link: https://lkml.kernel.org/r/20210818152457.35846-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Rik van Riel <riel@surriel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Fri, 20 Aug 2021 02:04:24 +0000 (19:04 -0700)]
mm/hwpoison: retry with shake_page() for unhandlable pages
HWPoisonHandlable() sometimes returns false for typical user pages due
to races with average memory events like transfers over LRU lists. This
causes failures in hwpoison handling.
There's retry code for such a case but does not work because the retry
loop reaches the retry limit too quickly before the page settles down to
handlable state. Let get_any_page() call shake_page() to fix it.
[naoya.horiguchi@nec.com: get_any_page(): return -EIO when retry limit reached] Link: https://lkml.kernel.org/r/20210819001958.2365157-1-naoya.horiguchi@linux.dev Link: https://lkml.kernel.org/r/20210817053703.2267588-1-naoya.horiguchi@linux.dev Fixes: 25182f05ffed ("mm,hwpoison: fix race with hugetlb page allocation") Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reported-by: Tony Luck <tony.luck@intel.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 20 Aug 2021 02:04:21 +0000 (19:04 -0700)]
mm: memcontrol: fix occasional OOMs due to proportional memory.low reclaim
We've noticed occasional OOM killing when memory.low settings are in
effect for cgroups. This is unexpected and undesirable as memory.low is
supposed to express non-OOMing memory priorities between cgroups.
The reason for this is proportional memory.low reclaim. When cgroups
are below their memory.low threshold, reclaim passes them over in the
first round, and then retries if it couldn't find pages anywhere else.
But when cgroups are slightly above their memory.low setting, page scan
force is scaled down and diminished in proportion to the overage, to the
point where it can cause reclaim to fail as well - only in that case we
currently don't retry, and instead trigger OOM.
To fix this, hook proportional reclaim into the same retry logic we have
in place for when cgroups are skipped entirely. This way if reclaim
fails and some cgroups were scanned with diminished pressure, we'll try
another full-force cycle before giving up and OOMing.
[akpm@linux-foundation.org: coding-style fixes]
Link: https://lkml.kernel.org/r/20210817180506.220056-1-hannes@cmpxchg.org Fixes: 9783aa9917f8 ("mm, memcg: proportional memory.{low,min} reclaim") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Leon Yang <lnyng@fb.com> Reviewed-by: Rik van Riel <riel@surriel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Chris Down <chris@chrisdown.name> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doug Berger [Fri, 20 Aug 2021 02:04:12 +0000 (19:04 -0700)]
mm/page_alloc: don't corrupt pcppage_migratetype
When placing pages on a pcp list, migratetype values over
MIGRATE_PCPTYPES get added to the MIGRATE_MOVABLE pcp list.
However, the actual migratetype is preserved in the page and should
not be changed to MIGRATE_MOVABLE or the page may end up on the wrong
free_list.
The impact is that HIGHATOMIC or CMA pages getting bulk freed from the
PCP lists could potentially end up on the wrong buddy list. There are
various consequences but minimally NR_FREE_CMA_PAGES accounting could
get screwed up.
Yang Shi [Fri, 20 Aug 2021 02:04:09 +0000 (19:04 -0700)]
Revert "mm: swap: check if swap backing device is congested or not"
Due to the change about how block layer detects congestion the
justification of commit 8fd2e0b505d1 ("mm: swap: check if swap backing
device is congested or not") doesn't stand anymore, so the commit could
be just reverted in order to solve the race reported by commit 2efa33fc7f6e ("mm/shmem: fix shmem_swapin() race with swapoff"). The
fix was reverted by the previous patch.
Link: https://lkml.kernel.org/r/20210810202936.2672-3-shy828301@gmail.com Signed-off-by: Yang Shi <shy828301@gmail.com> Suggested-by: Hugh Dickins <hughd@google.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Minchan Kim <minchan@kernel.org> Cc: David Hildenbrand <david@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yang Shi [Fri, 20 Aug 2021 02:04:05 +0000 (19:04 -0700)]
Revert "mm/shmem: fix shmem_swapin() race with swapoff"
Due to the change about how block layer detects congestion the
justification of commit 8fd2e0b505d1 ("mm: swap: check if swap backing
device is congested or not") doesn't stand anymore, so the commit could
be just reverted in order to solve the race reported by commit 2efa33fc7f6e ("mm/shmem: fix shmem_swapin() race with swapoff"), so the
fix commit could be just reverted as well.
And that fix is also kind of buggy as discussed by [1] and [2].
Linus Torvalds [Thu, 19 Aug 2021 22:32:58 +0000 (15:32 -0700)]
Merge tag 'soc-fixes-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Not much to see here. Half the fixes this time are for Qualcomm dts
files, fixing small mistakes on certain machines. The other fixes are:
- A 5.13 regression fix for freescale QE interrupt controller\
- A fix for TI OMAP gpt12 timer error handling
- A randconfig build regression fix for ixp4xx
- Another defconfig fix following the CONFIG_FB dependency rework"
* tag 'soc-fixes-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: fsl: qe: fix static checker warning
ARM: ixp4xx: fix building both pci drivers
ARM: configs: Update the nhk8815_defconfig
bus: ti-sysc: Fix error handling for sysc_check_active_timer()
soc: fsl: qe: convert QE interrupt controller to platform_device
arm64: dts: qcom: sdm845-oneplus: fix reserved-mem
arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem
arm64: dts: qcom: sc7280: Fixup cpufreq domain info for cpu7
arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem mapping
arm64: dts: qcom: msm8992-bullhead: Remove PSCI
arm64: dts: qcom: c630: fix correct powerdown pin for WSA881x
* tag 'net-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (42 commits)
net: dpaa2-switch: disable the control interface on error path
Revert "flow_offload: action should not be NULL when it is referenced"
iavf: Fix ping is lost after untrusted VF had tried to change MAC
i40e: Fix ATR queue selection
r8152: fix the maximum number of PLA bp for RTL8153C
r8152: fix writing USB_BP2_EN
mptcp: full fully established support after ADD_ADDR
mptcp: fix memory leak on address flush
net/rds: dma_map_sg is entitled to merge entries
net: mscc: ocelot: allow forwarding from bridge ports to the tag_8021q CPU port
net: asix: fix uninit value bugs
ovs: clear skb->tstamp in forwarding path
net: mdio-mux: Handle -EPROBE_DEFER correctly
net: mdio-mux: Don't ignore memory allocation errors
net: mdio-mux: Delete unnecessary devm_kfree
net: dsa: sja1105: fix use-after-free after calling of_find_compatible_node, or worse
sch_cake: fix srchost/dsthost hashing mode
ixgbe, xsk: clean up the resources in ixgbe_xsk_pool_enable error path
net: qlcnic: add missed unlock in qlcnic_83xx_flash_read32
mac80211: fix locking in ieee80211_restart_work()
...
Linus Torvalds [Thu, 19 Aug 2021 19:19:58 +0000 (12:19 -0700)]
Merge tag 'platform-drivers-x86-v5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Enable SW_TABLET_MODE support for the TP200s
- Enable WMI on two more Gigabyte motherboards
* tag 'platform-drivers-x86-v5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: gigabyte-wmi: add support for B450M S2H V2
platform/x86: gigabyte-wmi: add support for X570 GAMING X
platform/x86: asus-nb-wmi: Add tablet_mode_sw=lid-flip quirk for the TP200s
platform/x86: asus-nb-wmi: Allow configuring SW_TABLET_MODE method with a module option
Vladimir Oltean [Thu, 19 Aug 2021 14:17:55 +0000 (17:17 +0300)]
net: dpaa2-switch: disable the control interface on error path
Currently dpaa2_switch_takedown has a funny name and does not do the
opposite of dpaa2_switch_init, which makes probing fail when we need to
handle an -EPROBE_DEFER.
A sketch of what dpaa2_switch_init does:
dpsw_open
dpaa2_switch_detect_features
dpsw_reset
for (i = 0; i < ethsw->sw_attr.num_ifs; i++) {
dpsw_if_disable
dpsw_if_set_stp
dpsw_vlan_remove_if_untagged
dpsw_if_set_tci
dpsw_vlan_remove_if
}
dpsw_vlan_remove
alloc_ordered_workqueue
dpsw_fdb_remove
dpaa2_switch_ctrl_if_setup
When dpaa2_switch_takedown is called from the error path of
dpaa2_switch_probe(), the control interface, enabled by
dpaa2_switch_ctrl_if_setup from dpaa2_switch_init, remains enabled,
because dpaa2_switch_takedown does not call
dpaa2_switch_ctrl_if_teardown.
Since dpaa2_switch_probe might fail due to EPROBE_DEFER of a PHY, this
means that a second probe of the driver will happen with the control
interface directly enabled.
Which if we investigate the /dev/dpaa2_mc_console log, we find out is
caused by:
[E, ctrl_if_set_pools:2211, DPMNG] ctrl_if must be disabled
So make dpaa2_switch_takedown do the opposite of dpaa2_switch_init (in
reasonable limits, no reason to change STP state, re-add VLANs etc), and
rename it to something more conventional, like dpaa2_switch_teardown.
Fixes: 613c0a5810b7 ("staging: dpaa2-switch: enable the control interface") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20210819141755.1931423-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cited commit added a check to make sure 'action' is not NULL, but
'action' is already dereferenced before the check, when calling
flow_offload_has_one_action().
Therefore, the check does not make any sense and results in a smatch
warning:
include/net/flow_offload.h:322 flow_action_mixed_hw_stats_check() warn:
variable dereferenced before check 'action' (see line 319)
Fix by reverting this commit.
Cc: gushengxian <gushengxian@yulong.com> Fixes: 9ea3e52c5bc8 ("flow_offload: action should not be NULL when it is referenced") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20210819105842.1315705-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
iavf: Fix ping is lost after untrusted VF had tried to change MAC
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan G <Gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886c1 ("i40e: Fix queue-to-TC mapping on Tx") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We've added 3 non-merge commits during the last 3 day(s) which contain
a total of 3 files changed, 29 insertions(+), 6 deletions(-).
The main changes are:
1) Fix to clear zext_dst for dead instructions which was causing invalid program
rejections on JITs with bpf_jit_needs_zext such as s390x, from Ilya Leoshkevich.
2) Fix RCU splat in bpf_get_current_{ancestor_,}cgroup_id() helpers when they are
invoked from sleepable programs, from Yonghong Song.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests, bpf: Test that dead ldx_w insns are accepted
bpf: Clear zext_dst of dead insns
bpf: Add rcu_read_lock in bpf_get_current_[ancestor_]cgroup_id() helpers
====================
Takashi Iwai [Thu, 19 Aug 2021 15:29:45 +0000 (17:29 +0200)]
ASoC: intel: atom: Fix breakage for PCM buffer address setup
The commit 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
Arnd Bergmann [Thu, 19 Aug 2021 15:22:46 +0000 (17:22 +0200)]
Merge tag 'omap-for-v5.14/gpt12-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix for omap gpt12 timer error handling
Two of the recent fixes for ti-sysc driver had bad interaction for a
function return value that caused one of the fixes to not work so we
need to change the return value handling. Otherwise early beagleboard
variants still have a boot issue.
* tag 'omap-for-v5.14/gpt12-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix error handling for sysc_check_active_timer()
PCI/sysfs: Use correct variable for the legacy_mem sysfs object
Two legacy PCI sysfs objects "legacy_io" and "legacy_mem" were updated
to use an unified address space in the commit 636b21b50152 ("PCI: Revoke
mappings like devmem"). This allows for revocations to be managed from
a single place when drivers want to take over and mmap() a /dev/mem
range.
Following the update, both of the sysfs objects should leverage the
iomem_get_mapping() function to get an appropriate address range, but
only the "legacy_io" has been correctly updated - the second attribute
seems to be using a wrong variable to pass the iomem_get_mapping()
function to.
Thus, correct the variable name used so that the "legacy_mem" sysfs
object would also correctly call the iomem_get_mapping() function.
Fixes: 636b21b50152 ("PCI: Revoke mappings like devmem") Link: https://lore.kernel.org/r/20210812132144.791268-1-kw@linux.com Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Marcin Bachry [Thu, 22 Jul 2021 02:58:58 +0000 (22:58 -0400)]
PCI: Increase D3 delay for AMD Renoir/Cezanne XHCI
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com Signed-off-by: Marcin Bachry <hegel666@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Prike Liang <prike.liang@amd.com> Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Hayes Wang [Thu, 19 Aug 2021 03:05:37 +0000 (11:05 +0800)]
r8152: fix the maximum number of PLA bp for RTL8153C
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.
Fixes: 195aae321c82 ("r8152: support new chips") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang [Thu, 19 Aug 2021 03:05:36 +0000 (11:05 +0800)]
r8152: fix writing USB_BP2_EN
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a2a ("support request_firmware for RTL8153") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Aug 2021 11:17:05 +0000 (12:17 +0100)]
Merge branch 'mptcp-fixes'
Mat Martineau says:
====================
mptcp: Bug fixes
Here are two bug fixes for the net tree:
Patch 1 fixes a memory leak that could be encountered when clearing the
list of advertised MPTCP addresses.
Patch 2 fixes a protocol issue early in an MPTCP connection, to ensure
both peers correctly understand that the full MPTCP connection handshake
has completed even when the server side quickly sends an ADD_ADDR
option.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts [Wed, 18 Aug 2021 23:42:37 +0000 (16:42 -0700)]
mptcp: full fully established support after ADD_ADDR
If directly after an MP_CAPABLE 3WHS, the client receives an ADD_ADDR
with HMAC from the server, it is enough to switch to a "fully
established" mode because it has received more MPTCP options.
It was then OK to enable the "fully_established" flag on the MPTCP
socket. Still, best to check if the ADD_ADDR looks valid by looking if
it contains an HMAC (no 'echo' bit). If an ADD_ADDR echo is received
while we are not in "fully established" mode, it is strange and then
we should not switch to this mode now.
But that is not enough. On one hand, the path-manager has be notified
the state has changed. On the other hand, the "fully_established" flag
on the subflow socket should be turned on as well not to re-send the
MP_CAPABLE 3rd ACK content with the next ACK.
Fixes: 84dfe3677a6f ("mptcp: send out dedicated ADD_ADDR packet") Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We should not require an allocation to cleanup stuff.
Rework the code a bit so that the additional RCU work is no more needed.
Fixes: 1729cf186d8a ("mptcp: create the listening socket for new port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rutland [Wed, 18 Aug 2021 16:15:35 +0000 (17:15 +0100)]
arm64: initialize all of CNTHCTL_EL2
In __init_el2_timers we initialize CNTHCTL_EL2.{EL1PCEN,EL1PCTEN} with a
RMW sequence, leaving all other bits UNKNOWN.
In general, we should initialize all bits in a register rather than
using an RMW sequence, since most bits are UNKNOWN out of reset, and as
new bits are added to the reigster their reset value might not result in
expected behaviour.
In the case of CNTHCTL_EL2, FEAT_ECV added a number of new control bits
in previously RES0 bits, which reset to UNKNOWN values, and may cause
issues for EL1 and EL0:
* CNTHCTL_EL2.ECV enables the CNTPOFF_EL2 offset (which itself resets to
an UNKNOWN value) at EL0 and EL1. Since the offset could reset to
distinct values across CPUs, when the control bit resets to 1 this
could break timekeeping generally.
* CNTHCTL_EL2.{EL1TVT,EL1TVCT} trap EL0 and EL1 accesses to the EL1
virtual timer/counter registers to EL2. When reset to 1, this could
cause unexpected traps to EL2.
Initializing these bits to zero avoids these problems, and all other
bits in CNTHCTL_EL2 other than EL1PCEN and EL1PCTEN can safely be reset
to zero.
This patch ensures we initialize CNTHCTL_EL2 accordingly, only setting
EL1PCEN and EL1PCTEN, and setting all other bits to zero.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Oliver Upton <oupton@google.com> Cc: Will Deacon <will@kernel.org> Reviewed-by: Oliver Upton <oupton@google.com> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210818161535.52786-1-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org>
Gerd Rausch [Tue, 17 Aug 2021 17:04:37 +0000 (10:04 -0700)]
net/rds: dma_map_sg is entitled to merge entries
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba6b ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Vladimir Oltean [Tue, 17 Aug 2021 16:04:25 +0000 (19:04 +0300)]
net: mscc: ocelot: allow forwarding from bridge ports to the tag_8021q CPU port
Currently we are unable to ping a bridge on top of a felix switch which
uses the ocelot-8021q tagger. The packets are dropped on the ingress of
the user port and the 'drop_local' counter increments (the counter which
denotes drops due to no valid destinations).
Dumping the PGID tables, it becomes clear that the PGID_SRC of the user
port is zero, so it has no valid destinations.
But looking at the code, the cpu_fwd_mask (the bit mask of DSA tag_8021q
ports) is clearly missing from the forwarding mask of ports that are
under a bridge. So this has always been broken.
Looking at the version history of the patch, in v7
https://patchwork.kernel.org/project/netdevbpf/patch/20210125220333.1004365-12-olteanv@gmail.com/
the code looked like this:
/* Standalone ports forward only to DSA tag_8021q CPU ports */
unsigned long mask = cpu_fwd_mask;
while in v8 (the merged version)
https://patchwork.kernel.org/project/netdevbpf/patch/20210129010009.3959398-12-olteanv@gmail.com/
it looked like this:
Zhan Liu [Fri, 13 Aug 2021 15:31:04 +0000 (08:31 -0700)]
drm/amd/display: Use DCN30 watermark calc for DCN301
[why]
dcn301_calculate_wm_and_dl() causes flickering when external monitor is
connected.
This issue has been fixed before by commit 0e4c0ae59d7e
("drm/amdgpu/display: drop dcn301_calculate_wm_and_dl for now"), however
part of the fix was gone after commit 2cbcb78c9ee5 ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next").
[how]
Use dcn30_calculate_wm_and_dlg() instead as in the original fix.
Fixes: 2cbcb78c9ee5 ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next") Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Zhan Liu <zhan.liu@amd.com> Tested-by: Zhan Liu <zhan.liu@amd.com> Tested-by: Oliver Logush <oliver.logush@amd.com> Signed-off-by: Zhan Liu <zhan.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Wed, 18 Aug 2021 19:06:42 +0000 (12:06 -0700)]
Merge tag 'for-5.14-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix for cross-rename, adding a missing check for directory
and subvolume, this could lead to a crash"
* tag 'for-5.14-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: prevent rename2 from exchanging a subvol with a directory from different parents
Linus Torvalds [Wed, 18 Aug 2021 19:00:27 +0000 (12:00 -0700)]
Merge tag 'sound-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only a few regression fixes and trivial device quirks"
* tag 'sound-5.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/via: Apply runtime PM workaround for ASUS B23E
ALSA: hda: Fix hang during shutdown due to link reset
ALSA: hda/realtek: Enable 4-speaker output for Dell XPS 15 9510 laptop
ALSA: oxfw: fix functioal regression for silence in Apogee Duet FireWire
ALSA: hda - fix the 'Capture Switch' value change notifications
Linus Torvalds [Thu, 5 Aug 2021 17:04:43 +0000 (10:04 -0700)]
pipe: avoid unnecessary EPOLLET wakeups under normal loads
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88ca ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/ Fixes: 3a34b13a88ca ("pipe: make pipe writes always wake up readers") Reported-by: kernel test robot <oliver.sang@intel.com> Tested-by: Sandeep Patil <sspatil@android.com> Tested-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jani Nikula [Thu, 12 Aug 2021 13:23:54 +0000 (16:23 +0300)]
drm/i915/edp: fix eDP MSO pipe sanity checks for ADL-P
ADL-P supports stream splitter on pipe B in addition to pipe A. Update
the sanity check in intel_ddi_mso_get_config() to reflect this, and
remove the check in intel_ddi_mso_configure() as redundant with
encoder->pipe_mask. Abstract the splitter pipe mask to a single point of
truth while at it to avoid similar mistakes in the future.
Fixes: 7bc188cc2c8c ("drm/i915/adl_p: enable MSO on pipe B") Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Swati Sharma <swati2.sharma@intel.com> Reviewed-by: Swati Sharma <swati2.sharma@intel.com> Tested-by: Swati Sharma <swati2.sharma@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210812132354.10885-1-jani.nikula@intel.com
(cherry picked from commit f6864b27d6d324771d979694de7ca455afbad32a) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Anshuman Gupta [Tue, 10 Aug 2021 11:31:12 +0000 (17:01 +0530)]
drm/i915: Tweaked Wa_14010685332 for all PCHs
dispcnlunit1_cp_xosc_clkreq clock observed to be active on TGL-H platform
despite Wa_14010685332 original sequence,
thus blocks entry to deeper s0ix state.
The Tweaked Wa_14010685332 sequence fixes this issue, therefore use tweaked
Wa_14010685332 sequence for every PCH since PCH_CNP.
v2:
- removed RKL from comment and simplified condition. [Rodrigo]
Fixes: b896898c7369 ("drm/i915: Tweaked Wa_14010685332 for PCHs used on gen11 platforms") Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210810113112.31739-2-anshuman.gupta@intel.com
(cherry picked from commit 8b46cc6577f4bbef7e5909bb926da31d705f350f) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Liu Yi L [Tue, 17 Aug 2021 12:43:21 +0000 (20:43 +0800)]
iommu/vt-d: Fix incomplete cache flush in intel_pasid_tear_down_entry()
This fixes improper iotlb invalidation in intel_pasid_tear_down_entry().
When a PASID was used as nested mode, released and reused, the following
error message will appear:
[ 180.187556] Unexpected page request in Privilege Mode
[ 180.187565] Unexpected page request in Privilege Mode
[ 180.279933] Unexpected page request in Privilege Mode
[ 180.279937] Unexpected page request in Privilege Mode
Per chapter 6.5.3.3 of VT-d spec 3.3, when tear down a pasid entry, the
software should use Domain selective IOTLB flush if the PGTT of the pasid
entry is SL only or Nested, while for the pasid entries whose PGTT is FL
only or PT using PASID-based IOTLB flush is enough.
Fenghua Yu [Tue, 17 Aug 2021 12:43:20 +0000 (20:43 +0800)]
iommu/vt-d: Fix PASID reference leak
A PASID reference is increased whenever a device is bound to an mm (and
its PASID) successfully (i.e. the device's sdev user count is increased).
But the reference is not dropped every time the device is unbound
successfully from the mm (i.e. the device's sdev user count is decreased).
The reference is dropped only once by calling intel_svm_free_pasid() when
there isn't any device bound to the mm. intel_svm_free_pasid() drops the
reference and only frees the PASID on zero reference.
Fix the issue by dropping the PASID reference and freeing the PASID when
no reference on successful unbinding the device by calling
intel_svm_free_pasid() .
Pavel Skripkin [Tue, 17 Aug 2021 16:37:23 +0000 (19:37 +0300)]
net: asix: fix uninit value bugs
Syzbot reported uninit-value in asix_mdio_read(). The problem was in
missing error handling. asix_read_cmd() should initialize passed stack
variable smsr, but it can fail in some cases. Then while condidition
checks possibly uninit smsr variable.
Since smsr is uninitialized stack variable, driver can misbehave,
because smsr will be random in case of asix_read_cmd() failure.
Fix it by adding error handling and just continue the loop instead of
checking uninit value.
Added helper function for checking Host_En bit, since wrong loop was used
in 4 functions and there is no need in copy-pasting code parts.
Cc: Robert Foss <robert.foss@collabora.com> Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Reported-by: syzbot+a631ec9e717fb0423053@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
kaixi.fan [Wed, 18 Aug 2021 02:22:15 +0000 (10:22 +0800)]
ovs: clear skb->tstamp in forwarding path
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com> Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com> Reviewed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 18 Aug 2021 09:48:52 +0000 (10:48 +0100)]
Merge branch 'mdio-fixes'
Saravana Kannan says:
====================
Clean up and fix error handling in mdio_mux_init()
This patch series was started due to -EPROBE_DEFER not being handled
correctly in mdio_mux_init() and causing issues [1]. While at it, I also
did some more error handling fixes and clean ups. The -EPROBE_DEFER fix is
the last patch.
Ideally, in the last patch we'd treat any error similar to -EPROBE_DEFER
but I'm not sure if it'll break any board/platforms where some child
mdiobus never successfully registers. If we treated all errors similar to
-EPROBE_DEFER, then none of the child mdiobus will work and that might be a
regression. If people are sure this is not a real case, then I can fix up
the last patch to always fail the entire mdio-mux init if any of the child
mdiobus registration fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saravana Kannan [Wed, 18 Aug 2021 03:38:03 +0000 (20:38 -0700)]
net: mdio-mux: Handle -EPROBE_DEFER correctly
When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saravana Kannan [Wed, 18 Aug 2021 03:38:01 +0000 (20:38 -0700)]
net: mdio-mux: Delete unnecessary devm_kfree
The whole point of devm_* APIs is that you don't have to undo them if you
are returning an error that's going to get propagated out of a probe()
function. So delete unnecessary devm_kfree() call in the error return path.
Fixes: b60161668199 ("mdio: mux: Correct mdio_mux_init error path issues") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 17 Aug 2021 14:52:45 +0000 (17:52 +0300)]
net: dsa: sja1105: fix use-after-free after calling of_find_compatible_node, or worse
It seems that of_find_compatible_node has a weird calling convention in
which it calls of_node_put() on the "from" node argument, instead of
leaving that up to the caller. This comes from the fact that
of_find_compatible_node with a non-NULL "from" argument it only supposed
to be used as the iterator function of for_each_compatible_node(). OF
iterator functions call of_node_get on the next OF node and of_node_put()
on the previous one.
When of_find_compatible_node calls of_node_put, it actually never
expects the refcount to drop to zero, because the call is done under the
atomic devtree_lock context, and when the refcount drops to zero it
triggers a kobject and a sysfs file deletion, which assume blocking
context.
So any driver call to of_find_compatible_node is probably buggy because
an unexpected of_node_put() takes place.
What should be done is to use the of_get_compatible_child() function.
Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX") Link: https://lore.kernel.org/netdev/20210814010139.kzryimmp4rizlznt@skbuf/ Suggested-by: Frank Rowand <frowand.list@gmail.com> Suggested-by: Rob Herring <robh+dt@kernel.org> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed6088a ("sch_cake: Take advantage of skb->hash where appropriate") Reported-by: Pete Heist <pete@heistp.net> Tested-by: Pete Heist <pete@heistp.net> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Skeggs [Thu, 4 Mar 2021 09:53:01 +0000 (19:53 +1000)]
drm/nouveau: rip out nvkm_client.super
No longer required now that userspace can't touch anything that might
need it, and should fix DRM MM operations racing with each other, and
the random hangs/crashes that come with that.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
Ben Skeggs [Thu, 4 Mar 2021 09:16:18 +0000 (19:16 +1000)]
drm/nouveau: block a bunch of classes from userspace
Long ago, there had been plans for making use of a bunch of these APIs
from userspace and there's various checks in place to stop misbehaving.
Countless other projects have occurred in the meantime, and the pieces
didn't finish falling into place for that to happen.
They will (hopefully) in the not-too-distant future, but it won't look
quite as insane. The super checks are causing problems right now, and
are going to be removed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
Ben Skeggs [Mon, 9 Aug 2021 06:40:48 +0000 (16:40 +1000)]
drm/nouveau/disp: power down unused DP links during init
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
Wang Hai [Tue, 17 Aug 2021 20:37:36 +0000 (13:37 -0700)]
ixgbe, xsk: clean up the resources in ixgbe_xsk_pool_enable error path
In ixgbe_xsk_pool_enable(), if ixgbe_xsk_wakeup() fails,
We should restore the previous state and clean up the
resources. Add the missing clear af_xdp_zc_qps and unmap dma
to fix this bug.
Fixes: d49e286d354e ("ixgbe: add tracking of AF_XDP zero-copy state for each queue pair") Fixes: 4a9b32f30f80 ("ixgbe: fix potential RX buffer starvation for AF_XDP") Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210817203736.3529939-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 17 Aug 2021 22:08:13 +0000 (15:08 -0700)]
Merge tag 'wireless-drivers-2021-08-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.14
First set of fixes for v5.14 and nothing major this time. New devices
for iwlwifi and one fix for a compiler warning.
iwlwifi
* support for new devices
mt76
* fix compiler warning about MT_CIPHER_NONE
* tag 'wireless-drivers-2021-08-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
mt76: fix enum type mismatch
iwlwifi: add new so-jf devices
iwlwifi: add new SoF with JF devices
iwlwifi: pnvm: accept multiple HW-type TLVs
====================
Linus Torvalds [Tue, 17 Aug 2021 19:47:18 +0000 (09:47 -1000)]
Merge tag 'trace-v5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Limit the shooting in the foot of tp_printk
The "tp_printk" option redirects the trace event output to printk at
boot up. This is useful when a machine crashes before boot where the
trace events can not be retrieved by the in kernel ring buffer. But it
can be "dangerous" because trace events can be located in high
frequency locations such as interrupts and the scheduler, where a
printk can slow it down that it live locks the machine (because by the
time the printk finishes, the next event is triggered). Thus tp_printk
must be used with care.
It was discovered that the filter logic to trace events does not apply
to the tp_printk events. This can cause a surprise and live lock when
the user expects it to be filtered to limit the amount of events
printed to the console when in fact it still prints everything"
* tag 'trace-v5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Apply trace filters on all output channels
Mark Yacoub [Thu, 12 Aug 2021 19:49:17 +0000 (15:49 -0400)]
drm: Copy drm_wait_vblank to user before returning
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
Dinghao Liu [Mon, 16 Aug 2021 13:14:04 +0000 (21:14 +0800)]
net: qlcnic: add missed unlock in qlcnic_83xx_flash_read32
qlcnic_83xx_unlock_flash() is called on all paths after we call
qlcnic_83xx_lock_flash(), except for one error path on failure
of QLCRD32(), which may cause a deadlock. This bug is suggested
by a static analysis tool, please advise.
Ming Lei [Wed, 11 Aug 2021 14:26:24 +0000 (22:26 +0800)]
blk-mq: fix kernel panic during iterating over flush request
For fixing use-after-free during iterating over requests, we grabbed
request's refcount before calling ->fn in commit 2e315dc07df0 ("blk-mq:
grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter").
Turns out this way may cause kernel panic when iterating over one flush
request:
1) old flush request's tag is just released, and this tag is reused by
one new request, but ->rqs[] isn't updated yet
2) the flush request can be re-used for submitting one new flush command,
so blk_rq_init() is called at the same time
3) meantime blk_mq_queue_tag_busy_iter() is called, and old flush request
is retrieved from ->rqs[tag]; when blk_mq_put_rq_ref() is called,
flush_rq->end_io may not be updated yet, so NULL pointer dereference
is triggered in blk_mq_put_rq_ref().
Fix the issue by calling refcount_set(&flush_rq->ref, 1) after
flush_rq->end_io is set. So far the only other caller of blk_rq_init() is
scsi_ioctl_reset() in which the request doesn't enter block IO stack and
the request reference count isn't used, so the change is safe.
Fixes: 2e315dc07df0 ("blk-mq: grab rq->refcount before calling ->fn in blk_mq_tagset_busy_iter") Reported-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de> Tested-by: "Blank-Burian, Markus, Dr." <blankburian@uni-muenster.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/20210811142624.618598-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Wed, 11 Aug 2021 15:52:02 +0000 (23:52 +0800)]
blk-mq: don't grab rq's refcount in blk_mq_check_expired()
Inside blk_mq_queue_tag_busy_iter() we already grabbed request's
refcount before calling ->fn(), so needn't to grab it one more time
in blk_mq_check_expired().
Meantime remove extra request expire check in blk_mq_check_expired().
Cc: Keith Busch <kbusch@kernel.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/20210811155202.629575-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jason Wang [Tue, 17 Aug 2021 08:06:59 +0000 (16:06 +0800)]
virtio-net: use NETIF_F_GRO_HW instead of NETIF_F_LRO
Commit a02e8964eaf92 ("virtio-net: ethtool configurable LRO")
maps LRO to virtio guest offloading features and allows the
administrator to enable and disable those features via ethtool.
This leads to several issues:
- For a device that doesn't support control guest offloads, the "LRO"
can't be disabled triggering WARN in dev_disable_lro() when turning
off LRO or when enabling forwarding bridging etc.
- For a device that supports control guest offloads, the guest
offloads are disabled in cases of bridging, forwarding etc slowing
down the traffic.
Fix this by using NETIF_F_GRO_HW instead. Though the spec does not
guarantee packets to be re-segmented as the original ones,
we can add that to the spec, possibly with a flag for devices to
differentiate between GRO and LRO.
Further, we never advertised LRO historically before a02e8964eaf92
("virtio-net: ethtool configurable LRO") and so bridged/forwarded
configs effectively always relied on virtio receive offloads behaving
like GRO - thus even if this breaks any configs it is at least not
a regression.
Fixes: a02e8964eaf92 ("virtio-net: ethtool configurable LRO") Acked-by: Michael S. Tsirkin <mst@redhat.com> Reported-by: Ivan <ivan@prestigetransportation.com> Tested-by: Ivan <ivan@prestigetransportation.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Imre Deak [Mon, 16 Aug 2021 17:42:59 +0000 (20:42 +0300)]
ALSA: hda: Fix hang during shutdown due to link reset
During system shutdown codecs may be still active, and resetting the
controller->codec HW link in this state - based on the bug reporter's
tests - leads to the shutdown sequence to get stuck. This happens at
least on the reporter's KBL system with an ALC662 codec.
For now fix the issue by skipping the link reset step.
Fixes: 472e18f63c42 ("ALSA: hda: Release controller display power during shutdown/reboot")
References: https://bugzilla.kernel.org/show_bug.cgi?id=214045
References: https://gitlab.freedesktop.org/drm/intel/-/issues/3618#note_1024665 Reported-and-tested-by: youling257@gmail.com Cc: youling257@gmail.com Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://lore.kernel.org/r/20210816174259.2759103-1-imre.deak@intel.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 17 Aug 2021 01:42:09 +0000 (15:42 -1000)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This contains a fix for a potential boot failure due to a missing
Kconfig dependency for people upgrading with the DRBG enabled"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: drbg - select SHA512
When a packet is sent over a VRF, the POST_ROUTING hooks are called
twice: Once from the VRF interface, and once from the "actual"
interface the packet will be sent from:
1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct()
This causes the POST_ROUTING hooks to run.
2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again.
Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and
second vrf_l3_rcv() calls them again.
As an example, consider the following SNAT rule:
> iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1
In this case sending over a VRF will create 2 conntrack entries.
The first is from the VRF interface, which performs the IP SNAT.
The second will run the SNAT, but since the "expected reply" will remain
the same, conntrack randomizes the source port of the packet:
e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack
rules are:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1
udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is
SNAT-ed from 10000 --> 61033.
But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later
conntrack entry is matched:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1
udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
And a "port 61033 unreachable" ICMP packet is sent back.
The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(),
the skb already has a conntrack flow attached to it, which means
nf_conntrack_in() will not resolve the flow again.
This means only the dest port is "reverse-NATed" (61033 -> 10000) but
the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's
not received.
This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'.
The fix is then to reset the flow when skb is received on a VRF, to let
conntrack resolve the flow again (which now will hit the earlier flow).
To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by
running 'bash ./repro'):
$ cat run_in_A1.py
import logging
logging.getLogger("scapy.runtime").setLevel(logging.ERROR)
from scapy.all import *
import argparse
while True:
try:
# Periodically send in order to keep the conntrack entry alive.
s.send(b'a'*40)
resp = s.recvfrom(1024)
msg_name = resp[0].decode('utf-8').split('\0')[0]
print(f"Got {msg_name}", flush=True)
except Exception as e:
pass
$ cat repro.sh
ip netns del A1 2> /dev/null
ip netns del A2 2> /dev/null
ip netns add A1
ip netns add A2
ip -n A1 link add _v0 type veth peer name _v1 netns A2
ip -n A1 link set _v0 up
ip -n A2 link add e00000 type bond
ip -n A2 link add lo0 type dummy
ip -n A2 link add vrf_1 type vrf table 10001
ip -n A2 link set vrf_1 up
ip -n A2 link set e00000 master vrf_1
ip -n A2 addr add 1.1.1.1/24 dev e00000
ip -n A2 link set e00000 up
ip -n A2 link set _v1 master e00000
ip -n A2 link set _v1 up
ip -n A2 link set lo0 up
ip -n A2 addr add 2.2.2.2/32 dev lo0
ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000
ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001
Arnd Bergmann [Mon, 16 Aug 2021 21:22:02 +0000 (23:22 +0200)]
Merge tag 'qcom-arm64-fixes-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 fixes for v5.14
This fixes three regressions across Angler and Bullhead, introduced by
advancements in the platform definition. It then corrects the powerdown
GPIOs for the speaker amps on C630 and lastly fixes a typo that assigned
CPU7 in SC7280 to the wrong CPUfreq domain.
* tag 'qcom-arm64-fixes-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sdm845-oneplus: fix reserved-mem
arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem
arm64: dts: qcom: sc7280: Fixup cpufreq domain info for cpu7
arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem mapping
arm64: dts: qcom: msm8992-bullhead: Remove PSCI
arm64: dts: qcom: c630: fix correct powerdown pin for WSA881x
Jake Wang [Thu, 5 Aug 2021 18:43:41 +0000 (14:43 -0400)]
drm/amd/display: Ensure DCN save after VM setup
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Jake Wang <haonan.wang2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>