Linus Torvalds [Sun, 20 Jun 2021 16:44:52 +0000 (09:44 -0700)]
Merge tag 'sched_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Borislav Petkov:
"A single fix to restore fairness between control groups with equal
priority"
* tag 'sched_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Correctly insert cfs_rq's to list on unthrottle
Linus Torvalds [Sun, 20 Jun 2021 16:38:14 +0000 (09:38 -0700)]
Merge tag 'irq_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
"A single fix for GICv3 to not take an interrupt in an NMI context"
* tag 'irq_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Workaround inconsistent PMR setting on NMI entry
Linus Torvalds [Sun, 20 Jun 2021 16:09:58 +0000 (09:09 -0700)]
Merge tag 'x86_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"A first set of urgent fixes to the FPU/XSTATE handling mess^W code.
(There's a lot more in the pipe):
- Prevent corruption of the XSTATE buffer in signal handling by
validating what is being copied from userspace first.
- Invalidate other task's preserved FPU registers on XRSTOR failure
(#PF) because latter can still modify some of them.
- Restore the proper PKRU value in case userspace modified it
- Reset FPU state when signal restoring fails
Other:
- Map EFI boot services data memory as encrypted in a SEV guest so
that the guest can access it and actually boot properly
- Two SGX correctness fixes: proper resources freeing and a NUMA fix"
* tag 'x86_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Avoid truncating memblocks for SGX memory
x86/sgx: Add missing xa_destroy() when virtual EPC is destroyed
x86/fpu: Reset state for all signal restore failures
x86/pkru: Write hardware init value to PKRU when xstate is init
x86/process: Check PF_KTHREAD and not current->mm for kernel threads
x86/fpu: Invalidate FPU state after a failed XRSTOR from a user buffer
x86/fpu: Prevent state corruption in __fpu__restore_sig()
x86/ioremap: Map EFI-reserved memory as encrypted for SEV
Linus Torvalds [Sat, 19 Jun 2021 23:50:23 +0000 (16:50 -0700)]
Merge tag 'powerpc-5.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix initrd corruption caused by our recent change to use relative jump
labels.
Fix a crash using perf record on systems without a hardware PMU
backend.
Rework our 64-bit signal handling slighty to make it more closely
match the old behaviour, after the recent change to use unsafe user
accessors.
Thanks to Anastasia Kovaleva, Athira Rajeev, Christophe Leroy, Daniel
Axtens, Greg Kurz, and Roman Bolshakov"
* tag 'powerpc-5.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/perf: Fix crash in perf_instruction_pointer() when ppmu is not set
powerpc: Fix initrd corruption with relative jump labels
powerpc/signal64: Copy siginfo before changing regs->nip
powerpc/mem: Add back missing header to fix 'no previous prototype' error
Linus Torvalds [Sat, 19 Jun 2021 21:50:43 +0000 (14:50 -0700)]
Merge tag 'perf-tools-fixes-for-v5.13-2021-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix refcount usage when processing PERF_RECORD_KSYMBOL.
- 'perf stat' metric group fixes.
- Fix 'perf test' non-bash issue with stat bpf counters.
- Update unistd, in.h and socket.h with the kernel sources, silencing
perf build warnings.
* tag 'perf-tools-fixes-for-v5.13-2021-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
tools headers UAPI: Sync linux/in.h copy with the kernel sources
tools headers UAPI: Sync asm-generic/unistd.h with the kernel original
perf beauty: Update copy of linux/socket.h with the kernel sources
perf test: Fix non-bash issue with stat bpf counters
perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL
perf metricgroup: Return error code from metricgroup__add_metric_sys_event_iter()
perf metricgroup: Fix find_evsel_group() event selector
Linus Torvalds [Sat, 19 Jun 2021 15:45:34 +0000 (08:45 -0700)]
Merge tag 'riscv-for-linus-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A build fix to always build modules with the 'medany' code model, as
the module loader doesn't support 'medlow'.
- A Kconfig warning fix for the SiFive errata.
- A pair of fixes that for regressions to the recent memory layout
changes.
- A fix for the FU740 device tree.
* tag 'riscv-for-linus-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: fu740: fix cache-controller interrupts
riscv: Ensure BPF_JIT_REGION_START aligned with PMD size
riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name
riscv: sifive: fix Kconfig errata warning
riscv32: Use medany C model for modules
tools headers UAPI: Sync linux/in.h copy with the kernel sources
To pick the changes in:
321827477360934d ("icmp: don't send out ICMP messages with a source address of 0.0.0.0")
That don't result in any change in tooling, as INADDR_ are not used to
generate id->string tables used by 'perf trace'.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Those headers are used in some arches to generate the syscall table used
in 'perf trace' to translate syscall numbers into strings.
This addresses this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/asm-generic/unistd.h' differs from latest version at 'include/uapi/asm-generic/unistd.h'
diff -u tools/include/uapi/asm-generic/unistd.h include/uapi/asm-generic/unistd.h
Cc: Jan Kara <jack@suse.cz> Cc: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf beauty: Update copy of linux/socket.h with the kernel sources
To pick the changes in:
ea6932d70e223e02 ("net: make get_net_ns return error if NET_NS is disabled")
That don't result in any changes in the tables generated from that
header.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/perf/trace/beauty/include/linux/socket.h' differs from latest version at 'include/linux/socket.h'
diff -u tools/perf/trace/beauty/include/linux/socket.h include/linux/socket.h
Cc: Changbin Du <changbin.du@intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ian Rogers [Thu, 17 Jun 2021 18:42:13 +0000 (11:42 -0700)]
perf test: Fix non-bash issue with stat bpf counters
$(( .. )) is a bash feature but the test's interpreter is !/bin/sh,
switch the code to use expr.
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: bpf@vger.kernel.org Link: http://lore.kernel.org/lkml/20210617184216.2075588-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Riccardo Mancini [Sat, 12 Jun 2021 17:37:48 +0000 (19:37 +0200)]
perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL
ASan reported a memory leak of BPF-related ksymbols map and dso. The
leak is caused by refount never reaching 0, due to missing __put calls
in the function machine__process_ksymbol_register.
Once the dso is inserted in the map, dso__put() should be called
(map__new2() increases the refcount to 2).
The same thing applies for the map when it's inserted into maps
(maps__insert() increases the refcount to 2).
$ sudo ./perf record -- sleep 5
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.025 MB perf.data (8 samples) ]
Direct leak of 6992 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x8e4e53 in map__new2 /home/user/linux/tools/perf/util/map.c:216:20
#2 0x8cf68c in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:778:10
[...]
Indirect leak of 8702 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x8728d7 in dso__new_id /home/user/linux/tools/perf/util/dso.c:1256:20
#2 0x872015 in dso__new /home/user/linux/tools/perf/util/dso.c:1295:9
#3 0x8cf623 in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:774:21
[...]
Indirect leak of 1520 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x87b3da in symbol__new /home/user/linux/tools/perf/util/symbol.c:269:23
#2 0x888954 in map__process_kallsym_symbol /home/user/linux/tools/perf/util/symbol.c:710:8
[...]
Indirect leak of 1406 byte(s) in 19 object(s) allocated from:
#0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
#1 0x87b3da in symbol__new /home/user/linux/tools/perf/util/symbol.c:269:23
#2 0x8cfbd8 in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:803:8
[...]
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tommi Rantala <tommi.t.rantala@nokia.com> Link: http://lore.kernel.org/lkml/20210612173751.188582-1-rickyman7@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
John Garry [Thu, 10 Jun 2021 14:33:00 +0000 (22:33 +0800)]
perf metricgroup: Return error code from metricgroup__add_metric_sys_event_iter()
The error code is not set at all in the sys event iter function.
This may lead to an uninitialized value of "ret" in
metricgroup__add_metric() when no CPU metric is added.
Fix by properly setting the error code.
It is not necessary to init "ret" to 0 in metricgroup__add_metric(), as
if we have no CPU or sys event metric matching, then "has_match" should
be 0 and "ret" is set to -EINVAL.
However gcc cannot detect that it may not have been set after the
map_for_each_metric() loop for CPU metrics, which is strange.
Fixes: be335ec28efa8 ("perf metricgroup: Support adding metrics for system PMUs") Signed-off-by: John Garry <john.garry@huawei.com> Acked-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/1623335580-187317-3-git-send-email-john.garry@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The following command segfaults on my x86 broadwell:
$ ./perf stat -M frontend_bound,retiring,backend_bound,bad_speculation sleep 1
WARNING: grouped events cpus do not match, disabling group:
anon group { raw 0x10e }
anon group { raw 0x10e }
perf: util/evsel.c:1596: get_group_fd: Assertion `!(!leader->core.fd)' failed.
Aborted (core dumped)
The issue shows itself as a use-after-free in evlist__check_cpu_maps(),
whereby the leader of an event selector (evsel) has been deleted (yet we
still attempt to verify for an evsel).
Fundamentally the problem comes from metricgroup__setup_events() ->
find_evsel_group(), and has developed from the previous fix attempt in
commit 9c880c24cb0d ("perf metricgroup: Fix for metrics containing
duration_time").
The problem now is that the logic in checking if an evsel is in the same
group is subtly broken for the "cycles" event. For the "cycles" event,
the pmu_name is NULL; however the logic in find_evsel_group() may set an
event matched against "cycles" as used, when it should not be.
This leads to a condition where an evsel is set, yet its leader is not.
Fix the check for evsel pmu_name by not matching evsels when either has a
NULL pmu_name.
There is still a pre-existing metric issue whereby the ordering of the
metrics may break the 'stat' function, as discussed at:
https://lore.kernel.org/lkml/49c6fccb-b716-1bf0-18a6-cace1cdb66b9@huawei.com/
Fixes: 9c880c24cb0d ("perf metricgroup: Fix for metrics containing duration_time") Signed-off-by: John Garry <john.garry@huawei.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> # On a Thinkpad T450S Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/1623335580-187317-2-git-send-email-john.garry@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jisheng Zhang [Fri, 18 Jun 2021 14:09:13 +0000 (22:09 +0800)]
riscv: Ensure BPF_JIT_REGION_START aligned with PMD size
Andreas reported commit fc8504765ec5 ("riscv: bpf: Avoid breaking W^X")
breaks booting with one kind of defconfig, I reproduced a kernel panic
with the defconfig:
After some investigation, I think I found the root cause: commit 2bfc6cd81bd ("move kernel mapping outside of linear mapping") moves
BPF JIT region after the kernel:
The &_end is unlikely aligned with PMD size, so the front bpf jit
region sits with part of kernel .data section in one PMD size mapping.
But kernel is mapped in PMD SIZE, when bpf_jit_binary_lock_ro() is
called to make the first bpf jit prog ROX, we will make part of kernel
.data section RO too, so when we write to, for example memset the
.data section, MMU will trigger a store page fault.
To fix the issue, we need to ensure the BPF JIT region is PMD size
aligned. This patch acchieve this goal by restoring the BPF JIT region
to original position, I.E the 128MB before kernel .text section. The
modification to kasan_init.c is inspired by Alexandre.
Jisheng Zhang [Fri, 18 Jun 2021 14:01:36 +0000 (22:01 +0800)]
riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name
commit 2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear
mapping") makes use of MODULES_VADDR to populate kernel, BPF, modules
mapping. Currently, MODULES_VADDR is defined as below for RV64:
But kasan_init() has two local variables which are also named as _start,
_end, so MODULES_VADDR is evaluated with the local variable _end
rather than the global "_end" as we expected. Fix this issue by
renaming the two local variables.
Fixes: 2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear mapping") Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Linus Torvalds [Fri, 18 Jun 2021 23:39:03 +0000 (16:39 -0700)]
Merge tag 'for-5.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix, for a space accounting bug in zoned mode. It happens
when a block group is switched back rw->ro and unusable bytes (due to
zoned constraints) are subtracted twice.
It has user visible effects so I consider it important enough for late
-rc inclusion and backport to stable"
* tag 'for-5.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix negative space_info->bytes_readonly
- Avoid secondary bus resets on TI KeyStone C667X devices (Antti
Järvinen)
- Avoid secondary bus resets on some NVIDIA GPUs (Shanker Donthineni)
- Work around FLR erratum on Huawei Intelligent NIC VF (Chiqijun)
- Avoid broken ATS on AMD Navi14 GPU (Evan Quan)
- Trust Broadcom BCM57414 NIC to isolate functions even though it
doesn't advertise ACS support (Sriharsha Basavapatna)
- Work around AMD RS690 BIOSes that don't configure DMA above 4GB
(Mikel Rychliski)
- Fix panic during PIO transfer on Aardvark controller (Pali Rohár)
* tag 'pci-v5.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: aardvark: Fix kernel panic during PIO transfer
PCI: Add AMD RS690 quirk to enable 64-bit DMA
PCI: Add ACS quirk for Broadcom BCM57414 NIC
PCI: Mark AMD Navi14 GPU ATS as broken
PCI: Work around Huawei Intelligent NIC VF FLR erratum
PCI: Mark some NVIDIA GPUs to avoid bus reset
PCI: Mark TI C667X to avoid bus reset
PCI: tegra194: Fix MCFG quirk build regressions
PCI: of: Clear 64-bit flag for non-prefetchable memory below 4GB
afs: Re-enable freezing once a page fault is interrupted
If a task is killed during a page fault, it does not currently call
sb_end_pagefault(), which means that the filesystem cannot be frozen
at any time thereafter. This may be reported by lockdep like this:
====================================
WARNING: fsstress/10757 still has locks held!
5.13.0-rc4-build4+ #91 Not tainted
------------------------------------
1 lock held by fsstress/10757:
#0: ffff888104eac530
(
sb_pagefaults
as filesystem freezing is modelled as a lock.
Fix this by removing all the direct returns from within the function,
and using 'ret' to indicate whether we were interrupted or successful.
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.
Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Jun 2021 19:22:55 +0000 (12:22 -0700)]
Merge tag 'mac80211-for-net-2021-06-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of straggler fixes:
* a minstrel HT sample check fix
* peer measurement could double-free on races
* certificate file generation at build time could
sometimes hang
* some parameters weren't reset between connections
in mac80211
* some extensible elements were treated as non-
extensible, possibly causuing bad connections
(or failures) if the AP adds data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests/net: Add icmp.sh for testing ICMP dummy address responses
This adds a new icmp.sh selftest for testing that the kernel will respond
correctly with an ICMP unreachable message with the dummy (192.0.0.8)
source address when there are no IPv4 addresses configured to use as source
addresses.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
icmp: don't send out ICMP messages with a source address of 0.0.0.0
When constructing ICMP response messages, the kernel will try to pick a
suitable source address for the outgoing packet. However, if no IPv4
addresses are configured on the system at all, this will fail and we end up
producing an ICMP message with a source address of 0.0.0.0. This can happen
on a box routing IPv4 traffic via v6 nexthops, for instance.
Since 0.0.0.0 is not generally routable on the internet, there's a good
chance that such ICMP messages will never make it back to the sender of the
original packet that the ICMP message was sent in response to. This, in
turn, can create connectivity and PMTUd problems for senders. Fortunately,
RFC7600 reserves a dummy address to be used as a source for ICMP
messages (192.0.0.8/32), so let's teach the kernel to substitute that
address as a last resort if the regular source address selection procedure
fails.
Below is a quick example reproducing this issue with network namespaces:
ip netns add ns0
ip l add type veth peer netns ns0
ip l set dev veth0 up
ip a add 10.0.0.1/24 dev veth0
ip a add fc00:dead:cafe:42::1/64 dev veth0
ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2
ip -n ns0 l set dev veth0 up
ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0
ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1
ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0
ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1
tcpdump -tpni veth0 -c 2 icmp &
ping -w 1 10.1.0.1 > /dev/null
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64
IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
2 packets captured
2 packets received by filter
0 packets dropped by kernel
With this patch the above capture changes to:
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64
IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Juliusz Chroboczek <jch@irif.fr> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:33 +0000 (12:52 +0200)]
net: ll_temac: Fix TX BD buffer overwrite
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang") Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:28 +0000 (12:52 +0200)]
net: ll_temac: Add memory-barriers for TX BD access
Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.
In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.
When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.
Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Fri, 18 Jun 2021 10:52:23 +0000 (12:52 +0200)]
net: ll_temac: Make sure to free skb when it is completely used
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 18 Jun 2021 19:00:27 +0000 (12:00 -0700)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes
This patchset includes 3 small bug fixes to reinitialize PHY capabilities
after firmware reset, setup the chip's internal TQM fastpath ring
backing memory properly for RoCE traffic, and to free ethtool related
memory if driver probe fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Fri, 18 Jun 2021 06:07:27 +0000 (02:07 -0400)]
bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rukhsana Ansari [Fri, 18 Jun 2021 06:07:26 +0000 (02:07 -0400)]
bnxt_en: Fix TQM fastpath ring backing store computation
TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring. This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.
Fixes: c7dd7ab4b204 ("bnxt_en: Improve TQM ring context memory sizing formulas.") Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 18 Jun 2021 06:07:25 +0000 (02:07 -0400)]
bnxt_en: Rediscover PHY capabilities after firmware reset
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Fri, 18 Jun 2021 09:29:48 +0000 (11:29 +0200)]
cxgb4: fix wrong shift.
While fixing coverity warning, commit dd2c79677375 introduced typo in
shift value. Fix that.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de> Fixes: dd2c79677375 ("cxgb4: Fix unintentional sign extension issues") Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 18 Jun 2021 18:09:23 +0000 (11:09 -0700)]
Merge tag 'arc-5.13-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- ARCv2 userspace ABI not populating a few registers
- Unbork CONFIG_HARDENED_USERCOPY for ARC
* tag 'arc-5.13-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: fix CONFIG_HARDENED_USERCOPY
ARCv2: save ABI registers across signal handling
Linus Torvalds [Fri, 18 Jun 2021 17:57:09 +0000 (10:57 -0700)]
Merge tag 'trace-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Have recordmcount check for valid st_shndx otherwise some archs may
have invalid references for the mcount location.
- Two fixes done for mapping pids to task names. Traces were not
showing the names of tasks when they should have.
- Fix to trace_clock_global() to prevent it from going backwards
* tag 'trace-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do no increment trace_clock_global() by one
tracing: Do not stop recording comms if the trace file is being read
tracing: Do not stop recording cmdlines when tracing is off
recordmcount: Correct st_shndx handling
Linus Torvalds [Fri, 18 Jun 2021 17:42:36 +0000 (10:42 -0700)]
Merge tag 'pm-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Remove recently added frequency invariance support from the CPPC
cpufreq driver, because it has turned out to be problematic and it
cannot be fixed properly on time for 5.13 (Viresh Kumar)"
* tag 'pm-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "cpufreq: CPPC: Add support for frequency invariance"
Fan Du [Thu, 17 Jun 2021 19:46:57 +0000 (12:46 -0700)]
x86/mm: Avoid truncating memblocks for SGX memory
tl;dr:
Several SGX users reported seeing the following message on NUMA systems:
sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
This turned out to be the memblock code mistakenly throwing away SGX
memory.
=== Full Changelog ===
The 'max_pfn' variable represents the highest known RAM address. It can
be used, for instance, to quickly determine for which physical addresses
there is mem_map[] space allocated. The numa_meminfo code makes an
effort to throw out ("trim") all memory blocks which are above 'max_pfn'.
SGX memory is not considered RAM (it is marked as "Reserved" in the
e820) and is not taken into account by max_pfn. Despite this, SGX memory
areas have NUMA affinity and are enumerated in the ACPI SRAT table. The
existing SGX code uses the numa_meminfo mechanism to look up the NUMA
affinity for its memory areas.
In cases where SGX memory was above max_pfn (usually just the one EPC
section in the last highest NUMA node), the numa_memblock is truncated
at 'max_pfn', which is below the SGX memory. When the SGX code tries to
look up the affinity of this memory, it fails and produces an error message:
sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.
and assigns the memory to NUMA node 0.
Instead of silently truncating the memory block at 'max_pfn' and
dropping the SGX memory, add the truncated portion to
'numa_reserved_meminfo'. This allows the SGX code to later determine
the NUMA affinity of its 'Reserved' area.
Before, numa_meminfo looked like this (from 'crash'):
blk = { start = 0x0, end = 0x2080000000, nid = 0x0 }
{ start = 0x2080000000, end = 0x4000000000, nid = 0x1 }
numa_reserved_meminfo is empty.
With this, numa_meminfo looks like this:
blk = { start = 0x0, end = 0x2080000000, nid = 0x0 }
{ start = 0x2080000000, end = 0x4000000000, nid = 0x1 }
and numa_reserved_meminfo has an entry for node 1's SGX memory:
blk = { start = 0x4000000000, end = 0x4080000000, nid = 0x1 }
[ daveh: completely rewrote/reworked changelog ]
Fixes: 5d30f92e7631 ("x86/NUMA: Provide a range-to-target_node lookup facility") Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Fan Du <fan.du@intel.com> Signed-off-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dave Hansen <dave.hansen@intel.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20210617194657.0A99CB22@viggo.jf.intel.com
Linus Torvalds [Fri, 18 Jun 2021 17:36:18 +0000 (10:36 -0700)]
Merge tag 'drm-fixes-2021-06-18' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Not much happening in fixes land this week only one PR for two amdgpu
powergating fixes was waiting for me, maybe something will show up
over the weekend, maybe not.
amdgpu:
- GFX9 and 10 powergating fixes"
* tag 'drm-fixes-2021-06-18' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu/gfx10: enlarge CP_MEC_DOORBELL_RANGE_UPPER to cover full doorbell.
drm/amdgpu/gfx9: fix the doorbell missing when in CGPG issue.
Pali Rohár [Tue, 8 Jun 2021 20:36:55 +0000 (22:36 +0200)]
PCI: aardvark: Fix kernel panic during PIO transfer
Trying to start a new PIO transfer by writing value 0 in PIO_START register
when previous transfer has not yet completed (which is indicated by value 1
in PIO_START) causes an External Abort on CPU, which results in kernel
panic:
SError Interrupt on CPU0, code 0xbf000002 -- SError
Kernel panic - not syncing: Asynchronous SError Interrupt
To prevent kernel panic, it is required to reject a new PIO transfer when
previous one has not finished yet.
If previous PIO transfer is not finished yet, the kernel may issue a new
PIO request only if the previous PIO transfer timed out.
In the past the root cause of this issue was incorrectly identified (as it
often happens during link retraining or after link down event) and special
hack was implemented in Trusted Firmware to catch all SError events in EL3,
to ignore errors with code 0xbf000002 and not forwarding any other errors
to kernel and instead throw panic from EL3 Trusted Firmware handler.
Links to discussion and patches about this issue:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50
https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/
https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541
But the real cause was the fact that during link retraining or after link
down event the PIO transfer may take longer time, up to the 1.44s until it
times out. This increased probability that a new PIO transfer would be
issued by kernel while previous one has not finished yet.
After applying this change into the kernel, it is possible to revert the
mentioned TF-A hack and SError events do not have to be caught in TF-A EL3.
Link: https://lore.kernel.org/r/20210608203655.31228-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 7fbcb5da811b ("PCI: aardvark: Don't rely on jiffies while holding spinlock")
Other drivers required by this mainboard either don't support 64-bit DMA,
or have it disabled using driver specific quirks. For example, the ahci
driver has quirks to enable or disable 64-bit DMA depending on the BIOS
version (see ahci_sb600_enable_64bit() in ahci.c). This ahci quirk matches
against the SB600 SATA controller, but the real issue is almost certainly
with the RS690 PCI host that it was commonly attached to.
To avoid this issue in all drivers with 64-bit DMA support, fix the
configuration of the PCI host. If the kernel is aware of physical memory
above 4GB, but the BIOS never configured the PCI host with this
information, update the registers with our values.
The Broadcom BCM57414 NIC may be a multi-function device. While it does
not advertise an ACS capability, peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Evan Quan [Wed, 2 Jun 2021 02:12:55 +0000 (10:12 +0800)]
PCI: Mark AMD Navi14 GPU ATS as broken
Observed unexpected GPU hang during runpm stress test on 0x7341 rev 0x00.
Further debugging shows broken ATS is related.
Disable ATS on this part. Similar issues on other devices:
a2da5d8cc0b0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms") 45beb31d3afb ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken") 5e89cd303e3a ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
Suggested-by: Alex Deucher <alexander.deucher@amd.com> Link: https://lore.kernel.org/r/20210602021255.939090-1-evan.quan@amd.com Signed-off-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Cc: stable@vger.kernel.org
Chiqijun [Mon, 24 May 2021 22:44:07 +0000 (17:44 -0500)]
PCI: Work around Huawei Intelligent NIC VF FLR erratum
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the
device inoperable for the current system boot. It requires a system
hard-reboot to get the GPU device back to normal operating condition
post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the
issue.
This issue will be fixed in the next generation of hardware.
Antti Järvinen [Mon, 15 Mar 2021 10:26:06 +0000 (10:26 +0000)]
PCI: Mark TI C667X to avoid bus reset
Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS
automatically disables LTSSM when Secondary Bus Reset is received and
device stops working. Prevent bus reset for these devices. With this
change, the device can be assigned to VMs with VFIO, but it will leak state
between VMs.
Reference: https://e2e.ti.com/support/processors/f/791/t/954382 Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com Signed-off-by: Antti Järvinen <antti.jarvinen@gmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: stable@vger.kernel.org
Jon Hunter [Thu, 10 Jun 2021 06:41:34 +0000 (07:41 +0100)]
PCI: tegra194: Fix MCFG quirk build regressions
7f100744749e ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
caused a few build regressions:
- 7f100744749e removed the Makefile rule for CONFIG_PCIE_TEGRA194, so
pcie-tegra.c can no longer be built as a module. Restore that rule.
- 7f100744749e added "#ifdef CONFIG_PCIE_TEGRA194" around the native
driver, but that's only set when the driver is built-in (for a module,
CONFIG_PCIE_TEGRA194_MODULE is defined).
The ACPI quirk is completely independent of the rest of the native
driver, so move the quirk to its own file and remove the #ifdef in the
native driver.
- 7f100744749e added symbols that are always defined but used only when
CONFIG_PCIEASPM, which causes warnings when CONFIG_PCIEASPM is not set:
drivers/pci/controller/dwc/pcie-tegra194.c:259:18: warning: ‘event_cntr_data_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:250:18: warning: ‘event_cntr_ctrl_offset’ defined but not used [-Wunused-const-variable=]
drivers/pci/controller/dwc/pcie-tegra194.c:243:27: warning: ‘pcie_gen_freq’ defined but not used [-Wunused-const-variable=]
Punit Agrawal [Mon, 14 Jun 2021 23:04:57 +0000 (08:04 +0900)]
PCI: of: Clear 64-bit flag for non-prefetchable memory below 4GB
Alexandru and Qu reported this resource allocation failure on ROCKPro64 v2
and ROCK Pi 4B, both based on the RK3399:
pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff 64bit]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: BAR 14: no space for [mem size 0x00100000]
pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
"BAR 14" is the PCI bridge's 32-bit non-prefetchable window, and our PCI
allocation code isn't smart enough to allocate it in a host bridge window
marked as 64-bit, even though this should work fine.
A DT host bridge description includes the windows from the CPU address
space to the PCI bus space. On a few architectures (microblaze, powerpc,
sparc), the DT may also describe PCI devices themselves, including their
BARs.
Before 9d57e61bf723 ("of/pci: Add IORESOURCE_MEM_64 to resource flags for
64-bit memory addresses"), of_bus_pci_get_flags() ignored the fact that
some DT addresses described 64-bit windows and BARs. That was a problem
because the virtio virtual NIC has a 32-bit BAR and a 64-bit BAR, and the
driver couldn't distinguish them.
9d57e61bf723 set IORESOURCE_MEM_64 for those 64-bit DT ranges, which fixed
the virtio driver. But it also set IORESOURCE_MEM_64 for host bridge
windows, which exposed the fact that the PCI allocator isn't smart enough
to put 32-bit resources in those 64-bit windows.
Clear IORESOURCE_MEM_64 from host bridge windows since we don't need that
information.
tracing: Do no increment trace_clock_global() by one
The trace_clock_global() tries to make sure the events between CPUs is
somewhat in order. A global value is used and updated by the latest read
of a clock. If one CPU is ahead by a little, and is read by another CPU, a
lock is taken, and if the timestamp of the other CPU is behind, it will
simply use the other CPUs timestamp.
The lock is also only taken with a "trylock" due to tracing, and strange
recursions can happen. The lock is not taken at all in NMI context.
In the case where the lock is not able to be taken, the non synced
timestamp is returned. But it will not be less than the saved global
timestamp.
The problem arises because when the time goes "backwards" the time
returned is the saved timestamp plus 1. If the lock is not taken, and the
plus one to the timestamp is returned, there's a small race that can cause
the time to go backwards!
The above case shows to reads of trace_clock_global() on the same CPU, but
the second read returns one less than the first read. That is, time when
backwards, and this is not what is allowed by trace_clock_global().
This was triggered by heavy tracing and the ring buffer checker that tests
for the clock going backwards:
This happened more than once, and always for an off by one result. It also
started happening after commit aafe104aa9096 was added.
Cc: stable@vger.kernel.org Fixes: aafe104aa9096 ("tracing: Restructure trace_clock_global() to never block") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
tracing: Do not stop recording comms if the trace file is being read
A while ago, when the "trace" file was opened, tracing was stopped, and
code was added to stop recording the comms to saved_cmdlines, for mapping
of the pids to the task name.
Code has been added that only records the comm if a trace event occurred,
and there's no reason to not trace it if the trace file is opened.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
tracing: Do not stop recording cmdlines when tracing is off
The saved_cmdlines is used to map pids to the task name, such that the
output of the tracing does not just show pids, but also gives a human
readable name for the task.
If the name is not mapped, the output looks like this:
<...>-1316 [005] ...2 132.044039: ...
Instead of this:
gnome-shell-1316 [005] ...2 132.044039: ...
The names are updated when tracing is running, but are skipped if tracing
is stopped. Unfortunately, this stops the recording of the names if the
top level tracer is stopped, and not if there's other tracers active.
The recording of a name only happens when a new event is written into a
ring buffer, so there is no need to test if tracing is on or not. If
tracing is off, then no event is written and no need to test if tracing is
off or not.
Remove the check, as it hides the names of tasks for events in the
instance buffers.
Cc: stable@vger.kernel.org Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Johannes Berg [Fri, 18 Jun 2021 10:41:45 +0000 (13:41 +0300)]
mac80211: handle various extensible elements correctly
Various elements are parsed with a requirement to have an
exact size, when really we should only check that they have
the minimum size that we need. Check only that and therefore
ignore any additional data that they might carry.
Avraham Stern [Fri, 18 Jun 2021 10:41:31 +0000 (13:41 +0300)]
cfg80211: avoid double free of PMSR request
If cfg80211_pmsr_process_abort() moves all the PMSR requests that
need to be freed into a local list before aborting and freeing them.
As a result, it is possible that cfg80211_pmsr_complete() will run in
parallel and free the same PMSR request.
Fix it by freeing the request in cfg80211_pmsr_complete() only if it
is still in the original pmsr list.
Johannes Berg [Fri, 18 Jun 2021 10:41:29 +0000 (13:41 +0300)]
cfg80211: make certificate generation more robust
If all net/wireless/certs/*.hex files are deleted, the build
will hang at this point since the 'cat' command will have no
arguments. Do "echo | cat - ..." so that even if the "..."
part is empty, the whole thing won't hang.
Felix Fietkau [Thu, 17 Jun 2021 10:38:54 +0000 (12:38 +0200)]
mac80211: minstrel_ht: fix sample time check
We need to skip sampling if the next sample time is after jiffies, not before.
This patch fixes an issue where in some cases only very little sampling (or none
at all) is performed, leading to really bad data rates
Fixes: 80d55154b2f8 ("mac80211: minstrel_ht: significantly redesign the rate probing strategy") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20210617103854.61875-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Athira Rajeev [Thu, 17 Jun 2021 17:55:06 +0000 (13:55 -0400)]
powerpc/perf: Fix crash in perf_instruction_pointer() when ppmu is not set
On systems without any specific PMU driver support registered, running
perf record causes Oops.
The relevant portion from call trace:
BUG: Kernel NULL pointer dereference on read at 0x00000040
Faulting instruction address: 0xc0021f0c
Oops: Kernel access of bad area, sig: 11 [#1]
BE PAGE_SIZE=4K PREEMPT CMPCPRO
SAF3000 DIE NOTIFICATION
CPU: 0 PID: 442 Comm: null_syscall Not tainted 5.13.0-rc6-s3k-dev-01645-g7649ee3d2957 #5164
NIP: c0021f0c LR: c00e8ad8 CTR: c00d8a5c
NIP perf_instruction_pointer+0x10/0x60
LR perf_prepare_sample+0x344/0x674
Call Trace:
perf_prepare_sample+0x7c/0x674 (unreliable)
perf_event_output_forward+0x3c/0x94
__perf_event_overflow+0x74/0x14c
perf_swevent_hrtimer+0xf8/0x170
__hrtimer_run_queues.constprop.0+0x160/0x318
hrtimer_interrupt+0x148/0x3b0
timer_interrupt+0xc4/0x22c
Decrementer_virt+0xb8/0xbc
During perf record session, perf_instruction_pointer() is called to
capture the sample IP. This function in core-book3s accesses
ppmu->flags. If a platform specific PMU driver is not registered, ppmu
is set to NULL and accessing its members results in a crash. Fix this
crash by checking if ppmu is set.
Fixes: 2ca13a4cc56c ("powerpc/perf: Use regs->nip when SIAR is zero") Cc: stable@vger.kernel.org # v5.11+ Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/1623952506-1431-1-git-send-email-atrajeev@linux.vnet.ibm.com
Linus Torvalds [Thu, 17 Jun 2021 20:14:53 +0000 (13:14 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Miscellaneous bugfixes.
The main interesting one is a NULL pointer dereference reported by
syzkaller ("KVM: x86: Immediately reset the MMU context when the SMM
flag is cleared")"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: Fix kvm_check_cap() assertion
KVM: x86/mmu: Calculate and check "full" mmu_role for nested MMU
KVM: X86: Fix x86_emulator slab cache leak
KVM: SVM: Call SEV Guest Decommission if ASID binding fails
KVM: x86: Immediately reset the MMU context when the SMM flag is cleared
KVM: x86: Fix fall-through warnings for Clang
KVM: SVM: fix doc warnings
KVM: selftests: Fix compiling errors when initializing the static structure
kvm: LAPIC: Restore guard to prevent illegal APIC register access
Kees Cook [Thu, 17 Jun 2021 17:09:53 +0000 (10:09 -0700)]
net: qed: Fix memcpy() overflow of qed_dcbx_params()
The source (&dcbx_info->operational.params) and dest
(&p_hwfn->p_dcbx_info->set.config.params) are both struct qed_dcbx_params
(560 bytes), not struct qed_dcbx_admin_params (564 bytes), which is used
as the memcpy() size.
However it seems that struct qed_dcbx_operational_params
(dcbx_info->operational)'s layout matches struct qed_dcbx_admin_params
(p_hwfn->p_dcbx_info->set.config)'s 4 byte difference (3 padding, 1 byte
for "valid").
On the assumption that the size is wrong (rather than the source structure
type), adjust the memcpy() size argument to be 4 bytes smaller and add
a BUILD_BUG_ON() to validate any changes to the structure sizes.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linyu Yuan [Wed, 16 Jun 2021 23:32:32 +0000 (07:32 +0800)]
net: cdc_eem: fix tx fixup skb leak
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.
Fixes: 9f722c0978b0 ("usbnet: CDC EEM support (v5)") Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 815f62bf7427 ("[PATCH] SMP rewrite of mkiss") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: Fix an error handling path in 'be_probe()'
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: d6b6d9877878 ("be2net: use PCIe AER capability") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 17 Jun 2021 16:49:48 +0000 (09:49 -0700)]
Merge tag 'fixes_for_v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota and fanotify fixes from Jan Kara:
"A fixup finishing disabling of quotactl_path() syscall (I've missed
archs using different way to declare syscalls) and a fix of an fd leak
in error handling path of fanotify"
* tag 'fixes_for_v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: finish disable quotactl_path syscall
fanotify: fix copy_event_to_user() fid error clean up
Andrew Lunn [Mon, 14 Jun 2021 15:55:23 +0000 (17:55 +0200)]
usb: core: hub: Disable autosuspend for Cypress CY7C65632
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d758 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub") Cc: stable@vger.kernel.org Signed-off-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider we have a using block group on zoned btrfs.
|<- ZU ->|<- used ->|<---free--->|
`- Alloc offset
ZU: Zone unusable
Marking the block group read-only will migrate the zone unusable bytes
to the read-only bytes. So, we will have this.
|<- RO ->|<- used ->|<--- RO --->|
RO: Read only
When marking it back to read-write, btrfs_dec_block_group_ro()
subtracts the above "RO" bytes from the
space_info->bytes_readonly. And, it moves the zone unusable bytes back
and again subtracts those bytes from the space_info->bytes_readonly,
leading to negative bytes_readonly.
Aya Levin [Thu, 10 Jun 2021 11:20:28 +0000 (14:20 +0300)]
net/mlx5: Reset mkey index on creation
Reset only the index part of the mkey and keep the variant part. On
devlink reload, driver recreates mkeys, so the mkey index may change.
Trying to preserve the variant part of the mkey, driver mistakenly
merged the mkey index with current value. In case of a devlink reload,
current value of index part is dirty, so the index may be corrupted.
Fixes: 54c62e13ad76 ("{IB,net}/mlx5: Setup mkey variant before mr create command invocation") Signed-off-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Amir Tzin <amirtz@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dmytro Linkin [Fri, 14 May 2021 08:14:19 +0000 (11:14 +0300)]
net/mlx5e: Don't create devices during unload flow
Running devlink reload command for port in switchdev mode cause
resources to corrupt: driver can't release allocated EQ and reclaim
memory pages, because "rdma" auxiliary device had add CQs which blocks
EQ from deletion.
Erroneous sequence happens during reload-down phase, and is following:
1. detach device - suspends auxiliary devices which support it, destroys
others. During this step "eth-rep" and "rdma-rep" are destroyed,
"eth" - suspended.
2. disable SRIOV - moves device to legacy mode; as part of disablement -
rescans drivers. This step adds "rdma" auxiliary device.
3. destroy EQ table - <failure>.
Driver shouldn't create any device during unload flows. To handle that
implement MLX5_PRIV_FLAGS_DETACH flag, set it on device detach and unset
on device attach. If flag is set do no-op on drivers rescan.
Fixes: a925b5e309c9 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus") Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Decapsulation L3 on small inner packets which are less than
64 Bytes was done incorrectly. In small packets there is an
extra padding added in L2 which should not be included in L3
length. The issue was that after decapL3 the extra L2 padding
caused an update on the L3 length.
To avoid this issue the new header is pushed to the beginning
of the packet (offset 0) which should not cause a HW reparse
and update the L3 length.
Parav Pandit [Tue, 8 Jun 2021 16:03:24 +0000 (19:03 +0300)]
net/mlx5: E-Switch, Allow setting GUID for host PF vport
E-switch should be able to set the GUID of host PF vport.
Currently it returns an error. This results in below error
when user attempts to configure MAC address of the PF of an
external controller.
$ devlink port function set pci/0000:03:00.0/196608 \
hw_addr 00:00:00:11:22:33
mlx5_core 0000:03:00.0: mlx5_esw_set_vport_mac_locked:1876:(pid 6715):\
"Failed to set vport 0 node guid, err = -22.
RDMA_CM will not function properly for this VF."
Check for zero vport is no longer needed.
Fixes: 330077d14de1 ("net/mlx5: E-switch, Supporting setting devlink port function mac address") Signed-off-by: Yuval Avnery <yuvalav@nvidia.com> Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Bodong Wang <bodong@nvidia.com> Reviewed-by: Alaa Hleihel <alaa@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Parav Pandit [Tue, 8 Jun 2021 16:14:08 +0000 (19:14 +0300)]
net/mlx5: E-Switch, Read PF mac address
External controller PF's MAC address is not read from the device during
vport setup. Fail to read this results in showing all zeros to user
while the factory programmed MAC is a valid value.
Leon Romanovsky [Sun, 21 Mar 2021 17:57:14 +0000 (19:57 +0200)]
net/mlx5: Check that driver was probed prior attaching the device
The device can be requested to be attached despite being not probed.
This situation is possible if devlink reload races with module removal,
and the following kernel panic is an outcome of such race.
s390/ap: Fix hanging ioctl caused by wrong msg counter
When a AP queue is switched to soft offline, all pending
requests are purged out of the pending requests list and
'received' by the upper layer like zcrypt device drivers.
This is also done for requests which are already enqueued
into the firmware queue. A request in a firmware queue
may eventually produce an response message, but there is
no waiting process any more. However, the response was
counted with the queue_counter and as this counter was
reset to 0 with the offline switch, the pending response
caused the queue_counter to get negative. The next request
increased this counter to 0 (instead of 1) which caused
the ap code to assume there is nothing to receive and so
the response for this valid request was never tried to
fetch from the firmware queue.
This all caused a queue to not work properly after a
switch offline/online and in the end processes to hang
forever when trying to send a crypto request after an
queue offline/online switch cicle.
Fixed by a) making sure the counter does not drop below 0
and b) on a successful enqueue of a message has at least
a value of 1.
Additionally a warning is emitted, when a reply can't get
assigned to a waiting process. This may be normal operation
(process had timeout or has been killed) but may give a
hint that something unexpected happened (like this odd
behavior described above).
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Cc: stable@vger.kernel.org Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Kees Cook [Wed, 16 Jun 2021 19:53:59 +0000 (12:53 -0700)]
r8169: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 16 Jun 2021 19:53:33 +0000 (12:53 -0700)]
sh_eth: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 16 Jun 2021 19:53:03 +0000 (12:53 -0700)]
r8152: Avoid memcpy() over-reading of ETH_SS_STATS
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Righi [Wed, 16 Jun 2021 14:57:27 +0000 (16:57 +0200)]
selftests: net: use bash to run udpgro_fwd test case
udpgro_fwd.sh contains many bash specific operators ("[[", "local -r"),
but it's using /bin/sh; in some distro /bin/sh is mapped to /bin/dash,
that doesn't support such operators.
Force the test to use /bin/bash explicitly and prevent false positive
test failures.
Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Jun 2021 14:47:15 +0000 (07:47 -0700)]
net/af_unix: fix a data-race in unix_dgram_sendmsg / unix_release_sock
While unix_may_send(sk, osk) is called while osk is locked, it appears
unix_release_sock() can overwrite unix_peer() after this lock has been
released, making KCSAN unhappy.
Changing unix_release_sock() to access/change unix_peer()
before lock is released should fix this issue.
BUG: KCSAN: data-race in unix_dgram_sendmsg / unix_release_sock
write to 0xffff88810465a338 of 8 bytes by task 20852 on cpu 1:
unix_release_sock+0x4ed/0x6e0 net/unix/af_unix.c:558
unix_release+0x2f/0x50 net/unix/af_unix.c:859
__sock_release net/socket.c:599 [inline]
sock_close+0x6c/0x150 net/socket.c:1258
__fput+0x25b/0x4e0 fs/file_table.c:280
____fput+0x11/0x20 fs/file_table.c:313
task_work_run+0xae/0x130 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x156/0x190 kernel/entry/common.c:209
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:302
do_syscall_64+0x56/0x90 arch/x86/entry/common.c:57
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88810465a338 of 8 bytes by task 20888 on cpu 0:
unix_may_send net/unix/af_unix.c:189 [inline]
unix_dgram_sendmsg+0x923/0x1610 net/unix/af_unix.c:1712
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
__do_sys_sendmmsg net/socket.c:2519 [inline]
__se_sys_sendmmsg net/socket.c:2516 [inline]
__x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff888167905400 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 20888 Comm: syz-executor.0 Not tainted 5.13.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Righi [Wed, 16 Jun 2021 14:03:21 +0000 (16:03 +0200)]
selftests: net: veth: make test compatible with dash
veth.sh is a shell script that uses /bin/sh; some distro (Ubuntu for
example) use dash as /bin/sh and in this case the test reports the
following error:
# ./veth.sh: 21: local: -r: bad variable name
# ./veth.sh: 21: local: -r: bad variable name
This happens because dash doesn't support the option "-r" with local.
Moreover, in case of missing bpf object, the script is exiting -1, that
is an illegal number for dash:
exit: Illegal number: -1
Change the script to be compatible both with bash and dash and prevent
the errors above.
Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Jun 2021 13:42:02 +0000 (06:42 -0700)]
net/packet: annotate accesses to po->ifindex
Like prior patch, we need to annotate lockless accesses to po->ifindex
For instance, packet_getname() is reading po->ifindex (twice) while
another thread is able to change po->ifindex.
KCSAN reported:
BUG: KCSAN: data-race in packet_do_bind / packet_getname
write to 0xffff888143ce3cbc of 4 bytes by task 25573 on cpu 1:
packet_do_bind+0x420/0x7e0 net/packet/af_packet.c:3191
packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
__sys_bind+0x200/0x290 net/socket.c:1637
__do_sys_bind net/socket.c:1648 [inline]
__se_sys_bind net/socket.c:1646 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1646
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888143ce3cbc of 4 bytes by task 25578 on cpu 0:
packet_getname+0x5b/0x1a0 net/packet/af_packet.c:3525
__sys_getsockname+0x10e/0x1a0 net/socket.c:1887
__do_sys_getsockname net/socket.c:1902 [inline]
__se_sys_getsockname net/socket.c:1899 [inline]
__x64_sys_getsockname+0x3e/0x50 net/socket.c:1899
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00000000 -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25578 Comm: syz-executor.5 Not tainted 5.13.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 16 Jun 2021 13:42:01 +0000 (06:42 -0700)]
net/packet: annotate accesses to po->bind
tpacket_snd(), packet_snd(), packet_getname() and packet_seq_show()
can read po->num without holding a lock. This means other threads
can change po->num at the same time.
KCSAN complained about this known fact [1]
Add READ_ONCE()/WRITE_ONCE() to address the issue.
[1] BUG: KCSAN: data-race in packet_do_bind / packet_sendmsg
write to 0xffff888131a0dcc0 of 2 bytes by task 24714 on cpu 0:
packet_do_bind+0x3ab/0x7e0 net/packet/af_packet.c:3181
packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
__sys_bind+0x200/0x290 net/socket.c:1637
__do_sys_bind net/socket.c:1648 [inline]
__se_sys_bind net/socket.c:1646 [inline]
__x64_sys_bind+0x3d/0x50 net/socket.c:1646
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff888131a0dcc0 of 2 bytes by task 24719 on cpu 1:
packet_snd net/packet/af_packet.c:2899 [inline]
packet_sendmsg+0x317/0x3570 net/packet/af_packet.c:3040
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg net/socket.c:674 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
___sys_sendmsg net/socket.c:2404 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2433
__do_sys_sendmsg net/socket.c:2442 [inline]
__se_sys_sendmsg net/socket.c:2440 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2440
do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000 -> 0x1200
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24719 Comm: syz-executor.5 Not tainted 5.13.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 24803f38a5c0 ("igmp: do not remove igmp souce list info when set
link down"), the ip_mc_clear_src() in ip_mc_destroy_dev() was removed,
because it was also called in igmpv3_clear_delrec().
However, ip_mc_clear_src() called in igmpv3_clear_delrec() doesn't
release in_dev->mc_list->sources. And RCU_INIT_POINTER() assigns the
NULL to dev->ip_ptr. As a result, in_dev cannot be obtained through
inetdev_by_index() and then in_dev->mc_list->sources cannot be released
by ip_mc_del1_src() in the sock_close. Rough call sequence goes like:
So we still need to call ip_mc_clear_src() in ip_mc_destroy_dev() to free
in_dev->mc_list->sources.
Fixes: 24803f38a5c0 ("igmp: do not remove igmp souce list info ...") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Chengyang Fan <cy.fan@huawei.com> Acked-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang [Wed, 16 Jun 2021 09:14:26 +0000 (17:14 +0800)]
net: fec_ptp: fix issue caused by refactor the fec_devtype
Commit da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.")
refactor the fec_devtype, need adjust ptp driver accordingly.
Fixes: da722186f654 ("net: fec: set GPR bit on suspend by DT configuration.") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dongliang Mu [Wed, 16 Jun 2021 02:48:33 +0000 (10:48 +0800)]
net: usb: fix possible use-after-free in smsc75xx_bind
The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log