Arnd Bergmann [Mon, 17 Oct 2016 14:30:57 +0000 (16:30 +0200)]
fjes: fix format string for trace output
phys_addr_t may be wider than a pointer and has to be printed
using the special %pap format string, as pointed out by
this new warning.
arch/x86/include/../../../drivers/net/fjes/fjes_trace.h: In function ‘trace_raw_output_fjes_hw_start_debug_req’:
arch/x86/include/../../../drivers/net/fjes/fjes_trace.h:212:563: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
Note that this has to pass the address by reference instead of
casting it to a different type.
Fixes: 7a9b4b599eb0 ("fjes: ethtool -w and -W support for fjes driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Oct 2016 15:18:09 +0000 (11:18 -0400)]
Merge branch 'mv88e6xxx-interrupt-support'
Andrew Lunn says:
====================
Interrupt support for mv88e6xxx
This patchset add interrupt controller support to the MV88E6xxx. This
allows access to the interrupts the internal PHY generate. These
interrupts can then be associated to a PHY device in the device tree
and used by the PHY lib, rather than polling.
Since interrupt handling needs to make MDIO bus accesses, threaded
interrupts are used. The phylib needs to request the PHY interrupt
using the threaded IRQ API. This in term allows some simplification to
the code, in that the phylib interrupt handler can directly call
phy_change(), rather than use a work queue. The work queue is however
retained for the phy_mac_interrupt() call, which can be called in hard
interrupt context.
Since RFC v1:
Keep phy_mac_interrupt() callable in hard IRQ context.
The fix to trigger the phy state machine transitions on interrupts has
already been submitted, so is dropped from here.
Added back shared interrupts support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:53 +0000 (19:56 +0200)]
arm: vf610: zii devel b: Add support for switch interrupts
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:52 +0000 (19:56 +0200)]
net: phy: Use phy name when requesting the interrupt
Using the fixed name "phy_interrupt" is not very informative in
/proc/interrupts when there are a lot of phys, e.g. a device with an
Ethernet switch. So when requesting the interrupt, use the name of the
phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:51 +0000 (19:56 +0200)]
net: phy: Threaded interrupts allow some simplification
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:50 +0000 (19:56 +0200)]
net: phy: Use threaded IRQ, to allow IRQ from sleeping devices
The interrupt lines from PHYs maybe connected to I2C bus expanders, or
from switches on MDIO busses. Such interrupts are sourced from devices
which sleep, so use threaded interrupts. Threaded interrupts require
that the interrupt requester also uses the threaded API. Change the
phylib to use the threaded API, which is backwards compatible with
none-threaded IRQs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 16 Oct 2016 17:56:49 +0000 (19:56 +0200)]
net: dsa: mv88e6xxx: Implement interrupt support.
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sat, 15 Oct 2016 18:53:22 +0000 (11:53 -0700)]
rds: Remove duplicate prefix from rds_conn_path_error use
rds_conn_path_error already prefixes "RDS:" to the output.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sat, 15 Oct 2016 18:53:21 +0000 (11:53 -0700)]
rds: Remove unused rds_conn_error
This macro's last use was removed in commit 1c8c1847d7af0
("RDS: Update rds_conn_shutdown to work with rds_conn_path")
so make the macro and the __rds_conn_error function definition
and declaration disappear.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Mon, 17 Oct 2016 04:25:35 +0000 (21:25 -0700)]
ila: Don't use dest cache when gateway is set
If the gateway is set on an ILA route we don't need to bother with using
the destination cache in the ILA route. Translation does not change the
routing in this case so we can stick with orig_output in the lwstate
output function.
Tested: Ran netperf with and without gateway for LWT route.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sat, 15 Oct 2016 15:40:30 +0000 (17:40 +0200)]
ipvlan: constify l3mdev_ops structure
This l3mdev_ops structure is only stored in the l3mdev_ops field of a
net_device structure. This field is declared const, so the l3mdev_ops
structure can be declared as const also. Additionally drop the
__read_mostly annotation.
The semantic patch that adds const is as follows:
(http://coccinelle.lip6.fr/)
David S. Miller [Sat, 15 Oct 2016 21:33:42 +0000 (17:33 -0400)]
Merge branch 'ila-cached-route'
Tom Herbert says:
====================
ila: Cache a route in ILA lwt structure
Add a dst_cache to ila_lwt structure. This holds a cached route for the
translated address. In ila_output we now perform a route lookup after
translation and if possible (destination in original route is full 128
bits) we set the dst_cache. Subsequent calls to ila_output can then use
the cache to avoid the route lookup.
This eliminates the need to set the gateway on ILA routes as previously
was being done. Now we can do somthing like:
./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \
csum-mode neutral-map dev eth0 ## No via needed!
Also, add destroy_state to lwt ops. We need this do destroy the
dst_cache.
- v2
- Fixed comparisons to fc_dst_len to make comparison against number
of bits in data structure not bytes.
- Move destroy_state under build_state (requested by Jiri)
- Other minor cleanup
Tested:
Running 200 TCP_RR streams:
Baseline, no ILA
1730716 tps
102/170/313 50/90/99% latencies
88.11 CPU utilization
Using ILA in both directions
1680428 tps
105/176/325 50/90/99% latencies
88.16 CPU utilization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 14 Oct 2016 18:25:37 +0000 (11:25 -0700)]
ila: Cache a route to translated address
Add a dst_cache to ila_lwt structure. This holds a cached route for the
translated address. In ila_output we now perform a route lookup after
translation and if possible (destination in original route is full 128
bits) we set the dst_cache. Subsequent calls to ila_output can then use
the cache to avoid the route lookup.
This eliminates the need to set the gateway on ILA routes as previously
was being done. Now we can do something like:
./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \
csum-mode neutral-map dev eth0 ## No via needed!
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 14 Oct 2016 18:25:36 +0000 (11:25 -0700)]
lwtunnel: Add destroy state operation
Users of lwt tunnels may set up some secondary state in build_state
function. Add a corresponding destroy_state function to allow users to
clean up state. This destroy state function is called from lwstate_free.
Also, we now free lwstate using kfree_rcu so user can assume structure
is not freed before rcu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Oct 2016 16:04:58 +0000 (12:04 -0400)]
Merge branch 'fjes-next'
Taku Izumi says:
====================
FUJITSU Extended Socket driver version 1.2
This patchset updates FUJITSU Extended Socket network driver into version 1.2.
This includes the following enhancements:
- ethtool -d support
- ethtool -S enhancement
- ethtool -w/-W support
- Add some debugging feature (tracepoints etc)
v1 -> v2:
- Use u64 instead of phys_addr_t as TP_STRUCT__entry
- Use ethtool facility to achieve debug mode instead of using debugfs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taku Izumi [Fri, 14 Oct 2016 11:28:07 +0000 (20:28 +0900)]
fjes: Add debugfs entry for EP status information in fjes driver
This patch adds debugfs entry to show EP status information.
You can get each EP's status information like the following:
# cat /sys/kernel/debug/fjes/fjes.0/status
EPID STATUS SAME_ZONE CONNECTED
ep0 shared Y Y
ep1 - - -
ep2 unshared N N
ep3 unshared N N
ep4 unshared N N
ep5 unshared N N
ep6 unshared N N
ep7 unshared N N
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Oct 2016 15:59:59 +0000 (11:59 -0400)]
Merge branch 'qed-next'
Manish Chopra says:
====================
qed*: driver updates
There are several new additions in this series;
Most are connected to either Tx offloading or Rx classifications
[either fastpath changes or supporting configuration].
In addition, there's a single IOV enhancement.
Please consider applying this series to `net-next'.
V2->V3:
Fixes below kbuild warning
call to '__compiletime_assert_60' declared with
attribute error: Need native word sized stores/loads for atomicity.
V1->V2:
Added a fix for the race in ramrod handling
pointed by Eric Dumazet [patch 7].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 14 Oct 2016 09:19:23 +0000 (05:19 -0400)]
qed: Fix possible race when reading firmware return code.
While handling SPQ ramrod completion, there is a possible race
where driver might not read updated fw return code based on
ramrod completion done. This patch ensures that fw return code
is written first and then completion done flag is updated
using appropriate memory barriers.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Fri, 14 Oct 2016 09:19:22 +0000 (05:19 -0400)]
qed: Handle malicious VFs events
Malicious VFs might be caught in several different methods:
- Misusing their bar permission and being blocked by hardware.
- Misusing their fastpath logic and being blocked by firmware.
- Misusing their interaction with their PF via hw-channel,
and being blocked by PF driver.
On the first two items, firmware would indicate to driver that
the VF is to be considered malicious, but would sometime still
allow the VF to communicate with the PF [depending on the exact
nature of the malicious activity done by the VF].
The current existing logic on the PF side lacks handling of such events,
and might allow the PF to perform some incorrect configuration on behalf
of a VF that was previously indicated as malicious.
The new scheme is simple -
Once the PF determines a VF is malicious it would:
a. Ignore any further requests on behalf of the VF-driver.
b. Prevent any configurations initiated by the hyperuser for
the malicious VF, as firmware isn't willing to serve such.
The malicious indication would be cleared upon the VF flr,
after which it would become usable once again.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Fri, 14 Oct 2016 09:19:21 +0000 (05:19 -0400)]
qed: Allow chance for fast ramrod completions
Whenever a ramrod is being sent for some device configuration,
the driver is going to sleep at least 5ms between each iteration
of polling on the completion of the ramrod.
However, in almost every configuration scenario the firmware
would be able to comply and complete the ramrod in a manner of
several usecs. This is especially important in cases where there
might be a lot of sequential configurations applying to the hardware
[e.g., RoCE], in which case the existing scheme might cause some
visible user delays.
This patch changes the completion scheme - instead of immediately
starting to sleep for a 'long' period, allow the device to quickly
poll on the first iteration after a couple of usecs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Fri, 14 Oct 2016 09:19:20 +0000 (05:19 -0400)]
qed*: Allow unicast filtering
Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not
actually performing unicast MAC filtering.
While we're at it - relax a hard-coded limitation that limits each
interface into using at most 15 unicast MAC addresses before turning
promiscuous. Instead utilize the HW resources to their limit.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 14 Oct 2016 09:19:19 +0000 (05:19 -0400)]
qede: Prevent GSO on long Geneve headers
Due to hardware limitation, when transmitting a geneve-encapsulated
packet with more than 32 bytes worth of geneve options the hardware
would not be able to crack the packet and consider it a regular UDP
packet.
This implements the ndo_features_check() in qede in order to prevent
GSO on said transmitted packets.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 14 Oct 2016 09:19:18 +0000 (05:19 -0400)]
qede: GSO support for tunnels with outer csum
This patch adds GSO support for GRE and UDP tunnels
where outer checksums are enabled.
Signed-off-by: Manish Chopra <manish.chopra@caviumnetworks.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Fri, 14 Oct 2016 09:19:17 +0000 (05:19 -0400)]
qed: Pass MAC hints to VFs
Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Oct 2016 14:23:07 +0000 (10:23 -0400)]
Merge branch 'ingress-actions'
Shmulik Ladkani says:
====================
act_mirred: Ingress actions support
This patch series implements action mirred 'ingress' actions
TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR.
This allows attaching filters whose target is to hand matching skbs into
the rx processing of a specified device.
v4:
in 4/4, check ret code of netif_receive_skb, as suggested by Cong Wang
v3:
in 4/4, addressed non coherency due to reading m->tcfm_eaction multiple
times, as spotted by Eric Dumazet
v2:
in 1/4, declare tcfm_mac_header_xmit as bool instead of int
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Thu, 13 Oct 2016 06:06:44 +0000 (09:06 +0300)]
net/sched: act_mirred: Implement ingress actions
Up until now, 'action mirred' supported only egress actions (either
TCA_EGRESS_REDIR or TCA_EGRESS_MIRROR).
This patch implements the corresponding ingress actions
TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR.
This allows attaching filters whose target is to hand matching skbs into
the rx processing of a specified device.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Thu, 13 Oct 2016 06:06:43 +0000 (09:06 +0300)]
net/sched: tc_mirred: Rename public predicates 'is_tcf_mirred_redirect' and 'is_tcf_mirred_mirror'
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Hariprasad S <hariprasad@chelsio.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Jiri Pirko <jiri@mellanox.com> Cc: Ido Schimmel <idosch@mellanox.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Thu, 13 Oct 2016 06:06:42 +0000 (09:06 +0300)]
net/sched: act_mirred: Refactor detection whether dev needs xmit at mac header
Move detection logic that tests whether device expects skb data to point
at mac_header upon xmit into a function.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Thu, 13 Oct 2016 06:06:41 +0000 (09:06 +0300)]
net/sched: act_mirred: Rename tcfm_ok_push to tcfm_mac_header_xmit and make it a bool
'tcfm_ok_push' specifies whether a mac_len sized push is needed upon
egress to the target device (if action is performed at ingress).
Rename it to 'tcfm_mac_header_xmit' as this is actually an attribute of
the target device (and use a bool instead of int).
This allows to decouple the attribute from the action to be taken.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan W. Nielsen [Wed, 12 Oct 2016 13:47:51 +0000 (15:47 +0200)]
net: phy: Cleanup the Edge-Rate feature in Microsemi PHYs.
Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
being specified as positive values instead of negative (both
documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
"vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com> Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix various build warnings in tlan/qed/xen-netback drivers, from
Arnd Bergmann.
2) Propagate proper error code in strparser's strp_recv(), from Geert
Uytterhoeven.
3) Fix accidental broadcast of RTM_GETTFILTER responses, from Eric
Dumazret.
4) Need to use list_for_each_entry_safe() in qed driver, from Wei
Yongjun.
5) Openvswitch 802.1AD bug fixes from Jiri Benc.
6) Cure BUILD_BUG_ON() in mlx5 driver, from Tom Herbert.
7) Fix UDP ipv6 checksumming in netvsc driver, from Stephen Hemminger.
8) stmmac driver fixes from Giuseppe CAVALLARO.
9) Fix access to mangled IP6CB in tcp, from Eric Dumazet.
10) Fix info leaks in tipc and rtnetlink, from Dan Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net: bridge: add the multicast_flood flag attribute to brport_attrs
net: axienet: Remove unused parameter from __axienet_device_reset
liquidio: CN23XX: fix a loop timeout
net: rtnl: info leak in rtnl_fill_vfinfo()
tipc: info leak in __tipc_nl_add_udp_addr()
net: ipv4: Do not drop to make_route if oif is l3mdev
net: phy: Trigger state machine on state change and not polling.
ipv6: tcp: restore IP6CB for pktoptions skbs
netvsc: Remove mistaken udp.h inclusion.
xen-netback: fix type mismatch warning
stmmac: fix error check when init ptp
stmmac: fix ptp init for gmac4
qed: fix old-style function definition
netvsc: fix checksum on UDP IPV6
net_sched: reorder pernet ops and act ops registrations
xen-netback: fix guest Rx stall detection (after guest Rx refactor)
drivers/ptp: Fix kernel memory disclosure
net/mlx5: Add MLX5_ARRAY_SET64 to fix BUILD_BUG_ON
qmi_wwan: add support for Quectel EC21 and EC25
openvswitch: add NETIF_F_HW_VLAN_STAG_TX to internal dev
...
Linus Torvalds [Fri, 14 Oct 2016 04:28:20 +0000 (21:28 -0700)]
Merge tag 'nfs-for-4.9-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"Highlights include:
Stable bugfixes:
- sunrpc: fix writ espace race causing stalls
- NFS: Fix inode corruption in nfs_prime_dcache()
- NFSv4: Don't report revoked delegations as valid in nfs_have_delegation()
- NFSv4: nfs4_copy_delegation_stateid() must fail if the delegation is invalid
- NFSv4: Open state recovery must account for file permission changes
- NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
Features:
- Add support for tracking multiple layout types with an ordered list
- Add support for using multiple backchannel threads on the client
- Add support for pNFS file layout session trunking
- Delay xprtrdma use of DMA API (for device driver removal)
- Add support for xprtrdma remote invalidation
- Add support for larger xprtrdma inline thresholds
- Use a scatter/gather list for sending xprtrdma RPC calls
- Add support for the CB_NOTIFY_LOCK callback
- Improve hashing sunrpc auth_creds by using both uid and gid
Bugfixes:
- Fix xprtrdma use of DMA API
- Validate filenames before adding to the dcache
- Fix corruption of xdr->nwords in xdr_copy_to_scratch
- Fix setting buffer length in xdr_set_next_buffer()
- Don't deadlock the state manager on the SEQUENCE status flags
- Various delegation and stateid related fixes
- Retry operations if an interrupted slot receives EREMOTEIO
- Make nfs boot time y2038 safe"
* tag 'nfs-for-4.9-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (100 commits)
NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
fs: nfs: Make nfs boot time y2038 safe
sunrpc: replace generic auth_cred hash with auth-specific function
sunrpc: add RPCSEC_GSS hash_cred() function
sunrpc: add auth_unix hash_cred() function
sunrpc: add generic_auth hash_cred() function
sunrpc: add hash_cred() function to rpc_authops struct
Retry operation on EREMOTEIO on an interrupted slot
pNFS: Fix atime updates on pNFS clients
sunrpc: queue work on system_power_efficient_wq
NFSv4.1: Even if the stateid is OK, we may need to recover the open modes
NFSv4: If recovery failed for a specific open stateid, then don't retry
NFSv4: Fix retry issues with nfs41_test/free_stateid
NFSv4: Open state recovery must account for file permission changes
NFSv4: Mark the lock and open stateids as invalid after freeing them
NFSv4: Don't test open_stateid unless it is set
NFSv4: nfs4_do_handle_exception() handle revoke/expiry of a single stateid
NFS: Always call nfs_inode_find_state_and_recover() when revoking a delegation
NFSv4: Fix a race when updating an open_stateid
NFSv4: Fix a race in nfs_inode_reclaim_delegation()
...
Linus Torvalds [Fri, 14 Oct 2016 04:04:42 +0000 (21:04 -0700)]
Merge tag 'nfsd-4.9' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"Some RDMA work and some good bugfixes, and two new features that could
benefit from user testing:
- Anna Schumacker contributed a simple NFSv4.2 COPY implementation.
COPY is already supported on the client side, so a call to
copy_file_range() on a recent client should now result in a
server-side copy that doesn't require all the data to make a round
trip to the client and back.
- Jeff Layton implemented callbacks to notify clients when contended
locks become available, which should reduce latency on workloads
with contended locks"
* tag 'nfsd-4.9' of git://linux-nfs.org/~bfields/linux:
NFSD: Implement the COPY call
nfsd: handle EUCLEAN
nfsd: only WARN once on unmapped errors
exportfs: be careful to only return expected errors.
nfsd4: setclientid_confirm with unmatched verifier should fail
nfsd: randomize SETCLIENTID reply to help distinguish servers
nfsd: set the MAY_NOTIFY_LOCK flag in OPEN replies
nfs: add a new NFS4_OPEN_RESULT_MAY_NOTIFY_LOCK constant
nfsd: add a LRU list for blocked locks
nfsd: have nfsd4_lock use blocking locks for v4.1+ locks
nfsd: plumb in a CB_NOTIFY_LOCK operation
NFSD: fix corruption in notifier registration
svcrdma: support Remote Invalidation
svcrdma: Server-side support for rpcrdma_connect_private
rpcrdma: RDMA/CM private message data structure
svcrdma: Skip put_page() when send_reply() fails
svcrdma: Tail iovec leaves an orphaned DMA mapping
nfsd: fix dprintk in nfsd4_encode_getdeviceinfo
nfsd: eliminate cb_minorversion field
nfsd: don't set a FL_LAYOUT lease for flexfiles layouts
Linus Torvalds [Fri, 14 Oct 2016 03:28:22 +0000 (20:28 -0700)]
Merge tag 'xfs-reflink-for-linus-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
< XFS has gained super CoW powers! >
----------------------------------
\ ^__^
\ (oo)\_______
(__)\ )\/\
||----w |
|| ||
Pull XFS support for shared data extents from Dave Chinner:
"This is the second part of the XFS updates for this merge cycle. This
pullreq contains the new shared data extents feature for XFS.
Given the complexity and size of this change I am expecting - like the
addition of reverse mapping last cycle - that there will be some
follow-up bug fixes and cleanups around the -rc3 stage for issues that
I'm sure will show up once the code hits a wider userbase.
What it is:
At the most basic level we are simply adding shared data extents to
XFS - i.e. a single extent on disk can now have multiple owners. To do
this we have to add new on-disk features to both track the shared
extents and the number of times they've been shared. This is done by
the new "refcount" btree that sits in every allocation group. When we
share or unshare an extent, this tree gets updated.
Along with this new tree, the reverse mapping tree needs to be updated
to track each owner or a shared extent. This also needs to be updated
ever share/unshare operation. These interactions at extent allocation
and freeing time have complex ordering and recovery constraints, so
there's a significant amount of new intent-based transaction code to
ensure that operations are performed atomically from both the runtime
and integrity/crash recovery perspectives.
We also need to break sharing when writes hit a shared extent - this
is where the new copy-on-write implementation comes in. We allocate
new storage and copy the original data along with the overwrite data
into the new location. We only do this for data as we don't share
metadata at all - each inode has it's own metadata that tracks the
shared data extents, the extents undergoing CoW and it's own private
extents.
Of course, being XFS, nothing is simple - we use delayed allocation
for CoW similar to how we use it for normal writes. ENOSPC is a
significant issue here - we build on the reservation code added in
4.8-rc1 with the reverse mapping feature to ensure we don't get
spurious ENOSPC issues part way through a CoW operation. These
mechanisms also help minimise fragmentation due to repeated CoW
operations. To further reduce fragmentation overhead, we've also
introduced a CoW extent size hint, which indicates how large a region
we should allocate when we execute a CoW operation.
With all this functionality in place, we can hook up .copy_file_range,
.clone_file_range and .dedupe_file_range and we gain all the
capabilities of reflink and other vfs provided functionality that
enable manipulation to shared extents. We also added a fallocate mode
that explicitly unshares a range of a file, which we implemented as an
explicit CoW of all the shared extents in a file.
As such, it's a huge chunk of new functionality with new on-disk
format features and internal infrastructure. It warns at mount time as
an experimental feature and that it may eat data (as we do with all
new on-disk features until they stabilise). We have not released
userspace suport for it yet - userspace support currently requires
download from Darrick's xfsprogs repo and build from source, so the
access to this feature is really developer/tester only at this point.
Initial userspace support will be released at the same time the kernel
with this code in it is released.
The new code causes 5-6 new failures with xfstests - these aren't
serious functional failures but things the output of tests changing
slightly due to perturbations in layouts, space usage, etc. OTOH,
we've added 150+ new tests to xfstests that specifically exercise this
new functionality so it's got far better test coverage than any
functionality we've previously added to XFS.
Darrick has done a pretty amazing job getting us to this stage, and
special mention also needs to go to Christoph (review, testing,
improvements and bug fixes) and Brian (caught several intricate bugs
during review) for the effort they've also put in.
Summary:
- unshare range (FALLOC_FL_UNSHARE) support for fallocate
- copy-on-write extent size hints (FS_XFLAG_COWEXTSIZE) for fsxattr
interface
- shared extent support for XFS
- copy-on-write support for shared extents
- copy_file_range support
- clone_file_range support (implements reflink)
- dedupe_file_range support
- defrag support for reverse mapping enabled filesystems"
* tag 'xfs-reflink-for-linus-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (71 commits)
xfs: convert COW blocks to real blocks before unwritten extent conversion
xfs: rework refcount cow recovery error handling
xfs: clear reflink flag if setting realtime flag
xfs: fix error initialization
xfs: fix label inaccuracies
xfs: remove isize check from unshare operation
xfs: reduce stack usage of _reflink_clear_inode_flag
xfs: check inode reflink flag before calling reflink functions
xfs: implement swapext for rmap filesystems
xfs: refactor swapext code
xfs: various swapext cleanups
xfs: recognize the reflink feature bit
xfs: simulate per-AG reservations being critically low
xfs: don't mix reflink and DAX mode for now
xfs: check for invalid inode reflink flags
xfs: set a default CoW extent size of 32 blocks
xfs: convert unwritten status of reverse mappings for shared files
xfs: use interval query for rmap alloc operations on shared files
xfs: add shared rmap map/unmap/convert log item types
xfs: increase log reservations for reflink
...
Linus Torvalds [Fri, 14 Oct 2016 00:08:58 +0000 (17:08 -0700)]
Merge tag 'pci-v4.9-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
PCI changes for the v4.9 merge window:
"Here are some more changes I'd like to have in v4.9. There's one
small Tegra bug fix in the PHY poweroff path, which is only used in
failure paths.
The rest is all strictly cleanup that should make host bridge drivers
more readable, but shouldn't actually change any behavior.
Summary:
- use local struct device pointers in many host bridge drivers for
clarity
- remove unused platform data
- use generic DesignWare accessors
- misc cleanups: remove redundant structure entries and re-order
structure members to put comon generic fields first etc"
* tag 'pci-v4.9-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
MAINTAINERS: Add maintainer for the PCIe Marvell Armada 8K driver
MAINTAINERS: Add DT binding to the Aardvark PCIe driver maintainer
PCI: rockchip: Indent "if" statement body
PCI: hisi: Reorder struct hisi_pcie
PCI: hisi: Pass device-specific struct to internal functions
PCI: hisi: Include register block base in PCIE_SYS_STATE4 address
PCI: dra7xx: Reorder struct dra7xx_pcie
PCI: xilinx-nwl: Remove unused platform data
PCI: xilinx-nwl: Add local struct device pointers
PCI: xilinx: Removed unused xilinx_pcie_assign_msi() argument
PCI: xilinx: Remove unused platform data
PCI: xilinx: Add local struct device pointers
PCI: xgene: Add register accessors
PCI: xgene: Pass struct xgene_pcie_port to setup functions
PCI: xgene: Remove unused platform data
PCI: tegra: Remove unused platform data
PCI: tegra: Add local struct device pointers
PCI: tegra: Fix argument order in tegra_pcie_phy_disable()
PCI: rockchip: Remove unused platform data
PCI: rcar-gen2: Add local struct device pointers
...
Linus Torvalds [Thu, 13 Oct 2016 23:52:39 +0000 (16:52 -0700)]
Merge tag 'platform-drivers-x86-v4.9-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers updates from Darren Hart:
"Cleanups, refactoring, and a couple bug fixes.
intel_pmc_core:
- avoid boot time warning for !CONFIG_DEBUGFS_FS
intel_pmc_ipc:
- Convert to use platform_device_register_full
asus-wmi:
- Filter buggy scan codes on ASUS Q500A
toshiba_bluetooth:
- Decouple an error checking status code
toshiba_haps:
- Change logging level from info to debug
- Split ACPI and HDD protection error handling
asus-laptop:
- get rid of parse_arg()
asus-wmi:
- fix asus ux303ub brightness issue
toshiba_acpi:
- Fix typo in *_cooling_method_set function
- Change error checking logic from TCI functions
- Clean up variable declaration"
* tag 'platform-drivers-x86-v4.9-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: intel_pmc_core: avoid boot time warning for !CONFIG_DEBUGFS_FS
platform/x86: intel_pmc_ipc: Convert to use platform_device_register_full
platform/x86: asus-wmi: Filter buggy scan codes on ASUS Q500A
platform/x86: toshiba_bluetooth: Decouple an error checking status code
platform/x86: toshiba_haps: Change logging level from info to debug
platform/x86: toshiba_haps: Split ACPI and HDD protection error handling
platform/x86: asus-laptop: get rid of parse_arg()
platform/x86: asus-wmi: fix asus ux303ub brightness issue
platform/x86: toshiba_acpi: Fix typo in *_cooling_method_set function
platform/x86: toshiba_acpi: Change error checking logic from TCI functions
platform/x86: toshiba_acpi: Clean up variable declaration
net: bridge: add the multicast_flood flag attribute to brport_attrs
When I added the multicast flood control flag, I also added an attribute
for it for sysfs similar to other flags, but I forgot to add it to
brport_attrs.
Fixes: 6e61a26957f4 ("net: bridge: add per-port multicast flood flag") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Thu, 13 Oct 2016 11:28:33 +0000 (13:28 +0200)]
net: axienet: Remove unused parameter from __axienet_device_reset
The dev parameter passed to __axienet_device_reset() is not used inside
the function, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Reviewed-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 13 Oct 2016 08:56:57 +0000 (11:56 +0300)]
liquidio: CN23XX: fix a loop timeout
This is supposed to loop 1000 times and then give up. The problem is
it's a post-op and after the loop we test if "loop" is zero when really
it would be -1. Fix this by making it a pre-op.
Fixes: 3648778c0c92 ("liquidio: CN23XX queue manipulation") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 13 Oct 2016 08:45:28 +0000 (11:45 +0300)]
net: rtnl: info leak in rtnl_fill_vfinfo()
The "vf_vlan_info" struct ends with a 2 byte struct hole so we have to
memset it to ensure that no stack information is revealed to user space.
Fixes: 20235b2144e0 ('net: Update API for VF vlan protocol 802.1ad support') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 13 Oct 2016 08:06:06 +0000 (11:06 +0300)]
tipc: info leak in __tipc_nl_add_udp_addr()
We should clear out the padding and unused struct members so that we
don't expose stack information to userspace.
Fixes: a2af3659d117 ('tipc: add the ability to get UDP options via netlink') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 12 Oct 2016 20:20:11 +0000 (13:20 -0700)]
net: ipv4: Do not drop to make_route if oif is l3mdev
Commit 41c4a006031b was a bit aggressive removing l3mdev calls in
the IPv4 stack. If the fib_lookup fails we do not want to drop to
make_route if the oif is an l3mdev device.
Also reverts e8705c9f22e8 ("net: l3mdev: Remove netif_index_is_l3_master")
which removed netif_index_is_l3_master.
Fixes: 41c4a006031b ("net: l3mdev: remove redundant calls") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 12 Oct 2016 20:14:53 +0000 (22:14 +0200)]
net: phy: Trigger state machine on state change and not polling.
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Cc: Kyle Roeschley <kyle.roeschley@ni.com> Tested-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Issue is that ip6_datagram_recv_specific_ctl() expects to find IP6CB
data that was moved at a different place in tcp_v6_rcv()
This patch moves tcp_v6_restore_cb() up and calls it from
tcp_v6_do_rcv() when np->pktoptions is set.
Fixes: 06c9029f9882 ("tcp: better TCP_SKB_CB layout to reduce cache line misses") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 12 Oct 2016 14:54:01 +0000 (16:54 +0200)]
xen-netback: fix type mismatch warning
Wiht the latest rework of the xen-netback driver, we get a warning
on ARM about the types passed into min():
drivers/net/xen-netback/rx.c: In function 'xenvif_rx_next_chunk':
include/linux/kernel.h:739:16: error: comparison of distinct pointer types lacks a cast [-Werror]
The reason is that XEN_PAGE_SIZE is not size_t here. There
is no actual bug, and we can easily avoid the warning using the
min_t() macro instead of min().
Fixes: 6fd0b7a0b30b ("xen-netback: refactor guest rx") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem when propagated the
failure of ptp_clock_register to open function.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The gmac 4.x version has not extended descriptors
(that are available on 3.x instead of).
While initializing the PTP module, the advanced PTP was
enabled in case of extended descriptors. This cannot be
applied for 4.x version where only the hardware capability
register has to show if the feature is present.
Patch also adds some extra netdev_(debug/inof) to better
dump the configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 12 Oct 2016 10:38:51 +0000 (12:38 +0200)]
s390/lcs: remove trailing space at end of dev_err message
There is a trailing white space at the end of a dev_err
message that does nothing useful - remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 12 Oct 2016 10:38:50 +0000 (12:38 +0200)]
s390/netiucv: improve checking of sysfs attribute buffer
High values are always wrong for netiucv's sysfs attribute "buffer".
But the current code does not detect values between 2**31 and 2**32
as invalid. Choosing type "unsigned int" for variable "bs1" and making
use of "kstrtouint()" improves the syntax checking for "buffer".
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 12 Oct 2016 10:38:49 +0000 (12:38 +0200)]
s390/netiucv: get rid of one memcpy in netiucv_printuser
Save a memcpy in netiucv_printuser().
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 10 Oct 2016 11:59:16 +0000 (13:59 +0200)]
qed: fix old-style function definition
The definition of qed_get_rdma_ops() is not a prototype unless
we add 'void' here, as indicated by this W=1 warning:
drivers/net/ethernet/qlogic/qed/qed_roce.c: In function ‘qed_get_rdma_ops’:
drivers/net/ethernet/qlogic/qed/qed_roce.c:2950:28: error: old-style function definition [-Werror=old-style-definition]
Fixes: b1772d9ff7cf ("qed: Add RoCE ll2 & GSI support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The software calculation of UDP checksum in Netvsc driver was
only handling IPv4 case. By using skb_checksum_help() instead
all protocols can be handled. Rearrange code to eliminate goto
and look like other drivers.
This is a temporary solution; recent versions of Window Server etc
do support UDP checksum offload, just need to do the appropriate negotiation
with host to validate before using. This will be done in later patch.
Please queue this for -stable as well.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Tue, 11 Oct 2016 17:56:45 +0000 (10:56 -0700)]
net_sched: reorder pernet ops and act ops registrations
Krister reported a kernel NULL pointer dereference after
tcf_action_init_1() invokes a_o->init(), it is a race condition
where one thread calling tcf_register_action() to initialize
the netns data after putting act ops in the global list and
the other thread searching the list and then calling
a_o->init(net, ...).
Fix this by moving the pernet ops registration before making
the action ops visible. This is fine because: a) we don't
rely on act_base in pernet ops->init(), b) in the worst case we
have a fully initialized netns but ops is still not ready so
new actions still can't be created.
Reported-by: Krister Johansen <kjlx@templeofstupid.com> Tested-by: Krister Johansen <kjlx@templeofstupid.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If a VIF has been ready for rx_stall_timeout (60s by default) and an
Rx ring is drained of all requests an Rx stall will be incorrectly
detected. When this occurs and the guest Rx queue is empty, the Rx
ring's event index will not be set and the frontend will not raise an
event when new requests are placed on the ring, permanently stalling
the VIF.
This is a regression introduced by 6fd0b7a0b30be (xen-netback:
refactor guest rx).
Fix this by reinstating the setting of queue->last_rx_time when
placing a packet onto the guest Rx ring.
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Paul Durrant <paul.durrant@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Tsyrklevich [Tue, 11 Oct 2016 13:02:47 +0000 (15:02 +0200)]
drivers/ptp: Fix kernel memory disclosure
The reserved field precise_offset->rsv is not cleared before being
copied to user space, leaking kernel stack memory. Clear the struct
before it's copied.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 12 Oct 2016 01:57:10 +0000 (04:57 +0300)]
net/mlx5: Add MLX5_ARRAY_SET64 to fix BUILD_BUG_ON
I am hitting this in mlx5:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c: In function
reclaim_pages_cmd.clone.0:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:346: error: call
to __compiletime_assert_346 declared with attribute error:
BUILD_BUG_ON failed: __mlx5_bit_off(manage_pages_out, pas[i]) % 64
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c: In function give_pages:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:291: error: call
to __compiletime_assert_291 declared with attribute error:
BUILD_BUG_ON failed: __mlx5_bit_off(manage_pages_in, pas[i]) % 64
Problem is that this is doing a BUILD_BUG_ON on a non-constant
expression because of trying to take offset of pas[i] in the
structure.
Fix is to create MLX5_ARRAY_SET64 that takes an additional argument
that is the field index to separate between BUILD_BUG_ON on the array
constant field and the indexed field to assign the value to.
There are two callers of MLX5_SET64 that are trying to get a variable
offset, change those to call MLX5_ARRAY_SET64 passing 'pas' and 'i'
as the arguments to use in the offset check and the indexed value
assignment.
Fixes: 2d5a47cdc0286 ("net/mlx5: Pages management commands via mlx5 ifc") Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 10 Oct 2016 19:12:49 +0000 (21:12 +0200)]
qmi_wwan: add support for Quectel EC21 and EC25
The Quectel EC21 and EC25 need the same "set DTR" request as devices
based on the MDM9230 chipset, but has no USB3 support. Our best guess
is that the "set DTR" functionality depends on chipset and/or
baseband firmware generation. But USB3 is still an optional feature.
Since we cannot enable this unconditionally for all older devices, and
there doesn't appear to be anything we can use in the USB descriptors
to identify these chips, we are forced to use a device specific quirk
flag.
Reported-and-tested-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc [Mon, 10 Oct 2016 15:02:44 +0000 (17:02 +0200)]
openvswitch: add NETIF_F_HW_VLAN_STAG_TX to internal dev
The internal device does support 802.1AD offloading since 9f12eb71df70
("openvswitch: 802.1AD Flow handling, actions, vlan parsing, netlink
attributes").
Signed-off-by: Jiri Benc <jbenc@redhat.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Acked-by: Eric Garver <e@erig.me> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 10 Oct 2016 14:08:28 +0000 (14:08 +0000)]
qed: Fix to use list_for_each_entry_safe() when delete items
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 10 Oct 2016 12:41:10 +0000 (14:41 +0200)]
tlan: avoid unused label with PCI=n
While build testing with randconfig on x86, I ran into this warning
that appears to have been around forever
drivers/net/ethernet/ti/tlan.c: In function ‘tlan_probe1’:
drivers/net/ethernet/ti/tlan.c:614:1: error: label ‘err_out’ defined but not used [-Werror=unused-label]
This can be trivially avoided by just moving the label into the
existing #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Mon, 10 Oct 2016 08:30:53 +0000 (09:30 +0100)]
xen-netback: (re-)create a debugfs node for hash information
It is useful to be able to see the hash configuration when running tests.
This patch adds a debugfs node for that purpose.
The original version of this patch (commit ab2ca0248278) was reverted due
to build failures caused by a conflict with commit c396ab3be800
("xen-netback: switch to threaded irq for control ring"). This new version
of the patch is nearly identical to the original, the only difference
being that creation of the debugfs node is predicated on 'ctrl_irq' being
non-zero rather then the now non-existent 'ctrl_task'.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Cc: David S. Miller <davem@davemloft.net> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 10 Oct 2016 03:25:55 +0000 (20:25 -0700)]
net_sched: do not broadcast RTM_GETTFILTER result
There are two ways to get tc filters from kernel to user space.
1) Full dump (tc_dump_tfilter())
2) RTM_GETTFILTER to get one precise filter, reducing overhead.
The second operation is unfortunately broadcasting its result,
polluting "tc monitor" users.
This patch makes sure only the requester gets the result, using
netlink_unicast() instead of rtnetlink_send()
Jamal cooked an iproute2 patch to implement "tc filter get" operation,
but other user space libraries already use RTM_GETTFILTER when a single
filter is queried, instead of dumping all filters.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 8 Oct 2016 03:40:16 +0000 (11:40 +0800)]
sctp: remove the old ttl expires policy
The prsctp polices include ttl expires policy already, we should remove
the old ttl expires codes, and just adjust the new polices' codes to be
compatible with the old one for users.
This patch is to remove all the old expires codes, and if prsctp polices
are not set, it will still set msg's expires_at and check the expires in
sctp_check_abandoned.
Note that asoc->prsctp_enable is set by default, so users can't feel any
difference even if they use the old expires api in userspace.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 8 Oct 2016 03:36:05 +0000 (11:36 +0800)]
sctp: reuse sent_count to avoid retransmitted chunks for RTT measurements
Now sctp uses chunk->resent to record if a chunk is retransmitted, for
RTT measurements with retransmitted DATA chunks. chunk->sent_count was
introduced to record how many times one chunk has been sent for prsctp
RTX policy before. We actually can know if one chunk is retransmitted
by checking chunk->sent_count is greater than 1.
This patch is to remove resent from sctp_chunk and reuse sent_count
to avoid retransmitted chunks for RTT measurements.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: centralize net_device MTU bounds checking
While looking into an MTU issue with sfc, I started noticing that almost
every NIC driver with an ndo_change_mtu function implemented almost
exactly the same range checks, and in many cases, that was the only
practical thing their ndo_change_mtu function was doing. Quite a few
drivers have either 68, 64, 60 or 46 as their minimum MTU value checked,
and then various sizes from 1500 to 65535 for their maximum MTU value. We
can remove a whole lot of redundant code here if we simple store min_mtu
and max_mtu in net_device, and check against those in net/core/dev.c's
dev_set_mtu().
This pair of patches looks to introduce centralized MTU range checking
infrastructure, while maintaining compatibility with all existing drivers,
and start to make use of it, converting all eth_change_mtu/ether_setup users
over to this new infra.
Assuming these pass review muster, I've got a ton of follow-on patches to
clean up MTU settings for everything in the kernel with an ndo_change_mtu.
This work is all staged in a (rebasing) git tree here:
https://github.com/jarodwilson/linux-muck
The master branch is based on net-next from Oct 7, and carries these two
patches, plus a ton of follow-on patches to eliminate MTU range checks
and change_mtu functions where possible. All patches were successfully
built across 160 various arch and config combos by the 0-day folks.
(Thanks to Andrew Lunn for the suggestion to get that going).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Sat, 8 Oct 2016 02:04:34 +0000 (22:04 -0400)]
net: deprecate eth_change_mtu, remove usage
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarod Wilson [Sat, 8 Oct 2016 02:04:33 +0000 (22:04 -0400)]
net: centralize net_device min/max MTU checking
While looking into an MTU issue with sfc, I started noticing that almost
every NIC driver with an ndo_change_mtu function implemented almost
exactly the same range checks, and in many cases, that was the only
practical thing their ndo_change_mtu function was doing. Quite a few
drivers have either 68, 64, 60 or 46 as their minimum MTU value checked,
and then various sizes from 1500 to 65535 for their maximum MTU value. We
can remove a whole lot of redundant code here if we simple store min_mtu
and max_mtu in net_device, and check against those in net/core/dev.c's
dev_set_mtu().
In theory, there should be zero functional change with this patch, it just
puts the infrastructure in place. Subsequent patches will attempt to start
using said infrastructure, with theoretically zero change in
functionality.
CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 12 Oct 2016 18:11:05 +0000 (11:11 -0700)]
Merge tag 'pwm/for-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes contains support for PWM signal capture in the STi
driver as well as support for the PWM controller found on Meson SoCs.
There's also support added for the MediaTek MT2701 and SunXi H3 to the
existing drivers.
Other than that there's a fair set of miscellaneous cleanups and fixes
across the board"
* tag 'pwm/for-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits)
pwm: meson: Handle unknown ID values
pwm: sti: Take the opportunity to conduct a little house keeping
pwm: sti: It's now valid for number of PWM channels to be zero
pwm: sti: Add PWM capture callback
pwm: sti: Add support for PWM capture interrupts
pwm: sti: Initialise PWM capture device data
pwm: sti: Supply PWM Capture clock handling
pwm: sti: Supply PWM capture register addresses and bit locations
pwm: sti: Only request clock rate when needed
pwm: sti: Reorganise register names in preparation for new functionality
pwm: sti: Rename channel => device
dt-bindings: pwm: sti: Update DT bindings for capture support
pwm: lpc-18xx: use pwm_set_chip_data
pwm: sunxi: Add H3 support
pwm: Add support for Meson PWM Controller
dt-bindings: pwm: Add bindings for Meson PWM Controller
pwm: samsung: Fix to use lowest div for large enough modulation bits
pwm: pwm-tipwmss: Remove all runtime PM gets/puts
pwm: cros-ec: Add __packed to prevent padding
pwm: Add MediaTek MT2701 display PWM driver support
...
Linus Torvalds [Wed, 12 Oct 2016 18:05:23 +0000 (11:05 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
* tag 'fbdev-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (42 commits)
video: smscufx: remove unused variable
matroxfb: fix size of memcpy
fbdev: ssd1307fb: fix a possible NULL dereference
fbdev: ssd1307fb: constify the device_info pointer
simplefb: Disable and release clocks and regulators in destroy callback
video: fbdev: constify fb_fix_screeninfo and fb_var_screeninfo structures
matroxfb: constify local structures
video: fbdev: i810: add in missing white space in error message text
video: fbdev: add missing \n at end of printk error message
ARM: exynos_defconfig: Remove old non-working MIPI driver
video: fbdev: exynos: Remove old non-working MIPI driver
omapfb: fix return value check in dsi_bind()
MAINTAINERS: update fbdev entries
video: fbdev: offb: Call pci_enable_device() before using the PCI VGA device
fbdev: vfb: simplify memory management
fbdev: vfb: add option for video mode
fbdev: vfb: add description to module parameters
video: fbdev: intelfb: remove impossible condition
fb: adv7393: off by one in probe function
video: fbdev: pxafb: add missing of_node_put() in of_get_pxafb_mode_info()
...
Linus Torvalds [Wed, 12 Oct 2016 17:23:41 +0000 (10:23 -0700)]
Disable the __builtin_return_address() warning globally after all
This affectively reverts commit a1e76d27ea6e ("Makefile: Mute warning
for __builtin_return_address(>0) for tracing only") because it turns out
that it really isn't tracing only - it's all over the tree.
We already also had the warning disabled separately for mm/usercopy.c
(which this commit also removes), and it turns out that we will also
want to disable it for get_lock_parent_ip(), that is used for at least
TRACE_IRQFLAGS. Which (when enabled) ends up being all over the tree.
Steven Rostedt had a patch that tried to limit it to just the config
options that actually triggered this, but quite frankly, the extra
complexity and abstraction just isn't worth it. We have never actually
had a case where the warning is actually useful, so let's just disable
it globally and not worry about it.
Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bjorn Helgaas [Wed, 12 Oct 2016 16:15:06 +0000 (11:15 -0500)]
Merge branches 'pci/host-armada', 'pci/host-artpec', 'pci/host-dra7xx', 'pci/host-exynos', 'pci/host-hisi', 'pci/host-imx6', 'pci/host-keystone', 'pci/host-layerscape', 'pci/host-qcom' and 'pci/host-spear' into next
* pci/host-armada:
MAINTAINERS: Add maintainer for the PCIe Marvell Armada 8K driver
PCI: armada: Reorder struct armada8k_pcie
PCI: armada: Pass device-specific struct to internal functions
PCI: armada: Use generic DesignWare accessors
PCI: armada: Remove redundant struct armada8k_pcie.base
PCI: armada: Add local base pointer
PCI: armada: Remove unused platform data
* pci/host-artpec:
PCI: artpec6: Add resource name comments
PCI: artpec6: Pass device-specific struct to internal functions
PCI: artpec6: Remove unnecessary artpec6_pcie_link_up()
PCI: artpec6: Use generic DesignWare accessors
PCI: artpec6: Add register accessors
PCI: artpec6: Remove unused platform data
PCI: artpec6: Add local struct device pointers
* pci/host-dra7xx:
PCI: dra7xx: Reorder struct dra7xx_pcie
PCI: dra7xx: Move struct pcie_port setup to probe function
PCI: dra7xx: Pass device-specific struct to internal functions
PCI: dra7xx: Use generic DesignWare accessors
PCI: dra7xx: Set drvdata at end of probe function
PCI: dra7xx: Remove redundant struct device pointer from dra7xx_pcie
PCI: dra7xx: Add local struct device pointers
Bjorn Helgaas [Wed, 12 Oct 2016 16:14:44 +0000 (11:14 -0500)]
Merge branches 'pci/host-aardvark', 'pci/host-altera', 'pci/host-iproc', 'pci/host-mvebu', 'pci/host-rcar', 'pci/host-rockchip', 'pci/host-tegra', 'pci/host-xgene' and 'pci/host-xilinx' into next
* pci/host-aardvark:
MAINTAINERS: Add DT binding to the Aardvark PCIe driver maintainer
PCI: aardvark: Remove unused platform data
PCI: aardvark: Add local struct device pointers
* pci/host-altera:
PCI: altera: Simplify TLP_CFG_DW1 usage
PCI: altera: Simplify TLB_CFG_DW0 usage
PCI: altera: Rename altera_pcie_valid_config() to altera_pcie_valid_device()
PCI: altera: Remove redundant platform_get_resource() return value check
PCI: altera: Remove unused platform data
PCI: altera: Add local struct device pointers
* pci/host-iproc:
PCI: iproc: Hard-code PCIe capability offset instead of searching
PCI: iproc: Remove redundant null pointer checking
PCI: iproc: Validate CSR base in BCMA setup code
PCI: iproc: Set drvdata at end of probe function
PCI: iproc: Add local struct device pointers
* pci/host-mvebu:
PCI: mvebu: Use existing of_node pointer
PCI: mvebu: Add local struct device pointers
Arnd Bergmann [Mon, 10 Oct 2016 11:12:58 +0000 (13:12 +0200)]
platform/x86: intel_pmc_core: avoid boot time warning for !CONFIG_DEBUGFS_FS
While looking at a patch that introduced a compile-time warning
"‘pmc_core_dev_state_get’ defined but not used" (I sent a patch
for debugfs to fix it), I noticed that the same patch caused
it in intel_pmc_core also introduced a bogus run-time warning:
"PMC Core: debugfs register failed".
The problem is the IS_ERR_OR_NULL() check that as usual gets
things wrong: when CONFIG_DEBUGFS_FS is disabled,
debugfs_create_dir() fails with an error code, and we don't
need to warn about it, unlike the case in which it returns
NULL.
This reverts the driver to the previous state of not warning
about CONFIG_DEBUGFS_FS being disabled. I chose not to
restore the driver to making a runtime error in debugfs
fatal in pmc_core_probe().
Fixes: b8bd00f32d6f ("intel_pmc_core: Convert to DEFINE_DEBUGFS_ATTRIBUTE") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Linus Torvalds [Wed, 12 Oct 2016 06:38:39 +0000 (23:38 -0700)]
Merge branch 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess.h prepwork from Al Viro:
"Preparations to tree-wide switch to use of linux/uaccess.h (which,
obviously, will allow to start unifying stuff for real). The last step
there, ie
is not taken here - I would prefer to do it once just before or just
after -rc1. However, everything should be ready for it"
* 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
remove a stray reference to asm/uaccess.h in docs
sparc64: separate extable_64.h, switch elf_64.h to it
score: separate extable.h, switch module.h to it
mips: separate extable.h, switch module.h to it
x86: separate extable.h, switch sections.h to it
remove stray include of asm/uaccess.h from cacheflush.h
mn10300: remove a bogus processor.h->uaccess.h include
xtensa: split uaccess.h into C and asm sides
bonding: quit messing with IOCTL
kill __kernel_ds_p off
mn10300: finish verify_area() off
frv: move HAVE_ARCH_UNMAPPED_AREA to pgtable.h
exceptions: detritus removal
Ursula Braun [Fri, 7 Oct 2016 13:51:48 +0000 (15:51 +0200)]
Subject: [PATCH] af_iucv: drop skbs rejected by filter
A packet filter might be installed for instance with setsockopt
SO_ATTACH_FILTER. af_iucv currently queues skbs rejected by filter
into the backlog queue. This does not make sense, since packets
rejected by filter can be dropped immediately. This patch adds
separate sk_filter return code checking, and dropping of packets
if applicable.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 7 Oct 2016 13:51:47 +0000 (15:51 +0200)]
Subject: [PATCH] af_iucv: enable control sends in case of SEND_SHUTDOWN
If a socket program has shut down the socket for sending, it can still
receive an undetermined number of packets. The AF_IUCV protocol for
HIPER transport requires sending of a WIN flag from time to time
from the receiver to the sender, otherwise the peer cannot continue
sending. That means sending of control flags must still work, even
though the AF_IUCV socket is shutdown for sending data.
sock_alloc_send_skb() returns with error EPIPE, if socket sk_shutdown
is SEND_SHUTDOWN. Thus this patch temporarily removes the send
shutdown attribute from the socket to enable transfer of control
flags.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Oct 2016 05:54:03 +0000 (01:54 -0400)]
Merge branch 'xgene-gpio'
Iyappan Subramanian says:
====================
drivers: net: xgene: fix: Use GPIO to get link status
Since the link value reported by the link status register is not
reliable if no SPF module inserted, this patchset fixes the issue by
using GPIO to determine the link status when no module inserted.
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log