Jan Kiszka [Wed, 8 Feb 2017 16:09:06 +0000 (17:09 +0100)]
serial: exar: Move Commtech adapters to 8250_exar as well
Those are Exar-based, too.
With the required refactoring of the code to fit into 8250_exar, we
automatically fix the same issue pci_xr17v35x_setup had before: 8XMODE,
FCTL, TXTRG and RXTRG were always only set for port 0. Now they are
initialized for the correct target port by using port.membase.
Now we can also cleanly fix the blacklist of 8250_pci so that all
Commtech devices are rejected and 8250_exar can handle them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kiszka [Wed, 8 Feb 2017 16:09:04 +0000 (17:09 +0100)]
serial: exar: Fix initialization of EXAR registers for ports > 0
So far, pci_xr17v35x_setup always initialized 8XMODE, FCTR & Co. for
port 0 because it used the address of that port instead of moving the
pointer according to the port number. Fix this and remove the unneeded
temporary ioremap by moving default_setup up and reusing the membase it
fills into the port structure.
Fixes: 7e31560af98d ("tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kiszka [Wed, 8 Feb 2017 16:09:03 +0000 (17:09 +0100)]
serial: exar: Fix mapping of port I/O resources
pcim_iomap_table only returns the table of mapping, it does not perform
them. For that, we need to call pcim_iomap, but only if that mapping was
not done before.
Fixes: 24ae6bd00203 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Do not set the RX trigger level for software timeout devices on reset;
there is no timeout by default, and data will rot.
2. Do set the RX trigger level for hardware timeout devices when set
via sysfs attribute.
tty/serial: atmel: ensure state is restored after suspending
When going to suspend, the UART registers may be lost because the power to
VDDcore is cut. This is not an issue in the normal case but when
no_console_suspend is used, we need to restore the registers in order to
get a functional console.
serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
On a Rockchip rk3399-based board during suspend/resume testing, we
found that we could get the console UART into a state where it would
print this to the console a lot:
serial8250: too much work for irq42
Followed eventually by:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 11s!
Upon debugging I found that we're in this state:
iir = 0x000000cc
lsr = 0x00000060
It appears that somehow we have a RX Timeout interrupt but there is no
actual data present to receive. When we're in this state the UART
driver claims that it handled the interrupt but it actually doesn't
really do anything. This means that we keep getting the interrupt
over and over again.
Normally we don't actually need to do anything special to handle a RX
Timeout interrupt. We'll notice that there is some data ready and
we'll read it, which will end up clearing the RX Timeout. In this
case we have a problem specifically because we got the RX TImeout
without any data. Reading a bogus byte is confirmed to get us out of
this state.
It's unclear how exactly the UART got into this state, but it is known
that the UART lines are essentially undriven and unpowered during
suspend, so possibly during resume some garbage / half transmitted
bits are seen on the line and put the UART into this state.
The UART on the rk3399 is a DesignWare based 8250 UART. From mailing
list posts, it appears that other people have run into similar
problems with DesignWare based IP. Presumably this problem is unique
to that IP, so I have placed the workaround there to avoid possibly of
accidentally triggering bad behavior on other IP. Also note the RX
Timeout behaves very differently in the DMA case, for for now the
workaround is only applied to the non-DMA case.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:19 +0000 (10:23 +0000)]
ARM: dts: STiH410-b2260: Enable HW flow-control
Hardware flow-control capability must be specified at a platform
level in order to inform the ASC driver that the platform is capable
(i.e. are the lines wired up, etc). STiH4{07,10} devices are indeed
capable, so let's provide the property.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:18 +0000 (10:23 +0000)]
ARM: dts: STiH407-family: Use new Pinctrl groups
Having just defined some new Pinctrl groups for when HW flow-control
is {en,dis}abled, let's reference them for use within the driver.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:17 +0000 (10:23 +0000)]
ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
Each serial port which supports HW flow-control should have 2 Pinctrl
groups. One for when HW flow-control is in progress, where the IP
will take over controlling the lines and another group which enables
the lines to be toggled using GPIO mechanisms.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:16 +0000 (10:23 +0000)]
ARM: dts: STiH410-b2260: Identify the UART RTS line
When hardware flow-control is disabled, manual toggling of the UART's
reset line (RTS) using userland applications (e.g. stty) is not
possible, since the ASC IP does not provide this functionality in the
same was as some other IPs do. Thus, we have to do this manually.
This patch configures the UART RTS line as a GPIO for manipulation
within the UART driver when HW flow-control is not enabled.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'uart-has-rtscts' property and 'rts-gpios|cts-gpios' are normally
mutually exclusive, however it is possible for some drivers to have
a dynamic approach, meaning that both properties can be relevant.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:14 +0000 (10:23 +0000)]
serial: st-asc: Use generic DT binding for announcing RTS/CTS lines
The initial binding 'st,hw-flow-control' isn't used anywhere, in neither
in upstream nor downstream kernels. It isn't even documented in
dt-bindings, so we can safely assume it's safe to swap to the generic
one.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:13 +0000 (10:23 +0000)]
serial: st-asc: (De)Register GPIOD and swap Pinctrl profiles
When hardware flow-control is disabled, manual toggling of the UART's
reset line (RTS) using userland applications (e.g. stty) is not
possible, since the ASC IP does not provide this functionality in the
same was as some other IPs do. Thus, we have to do this manually.
This patch ensures that when HW flow-control is disabled the RTS/CTS
lines are free to be registered via the GPIO API. It also ensures
any registered GPIO lines are unregistered when HW flow-control is
requested, allowing the IP to control them automatically.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:12 +0000 (10:23 +0000)]
serial: st-asc: Read in all Pinctrl states
There are now 2 possible separate/different Pinctrl states which can
be provided from platform data. One which encompasses the lines
required for HW flow-control (CTS/RTS) and another which does not
specify these lines, such that they can be used via GPIO mechanisms
for manually toggling (i.e. from a request by `stty`).
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:11 +0000 (10:23 +0000)]
serial: st-asc: Provide RTS functionality
Until this point, it has not been possible for userland serial
applications (e.g. stty) to toggle the UART RTS line. This can
be useful with certain configurations. For example, when using
a Mezzanine on a Linaro 96board, RTS line is used to take the
on-board microcontroller in and out of reset.
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lee Jones [Fri, 3 Feb 2017 10:23:10 +0000 (10:23 +0000)]
serial: st-asc: Ignore the parity error bit if 8-bit mode is enabled
The datasheet states:
"If the MODE field selects an 8-bit frame then this [parity error] bit
is undefined. Software should ignore this bit when reading 8-bit frames."
Acked-by: Peter Griffin <peter.griffin@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 3 Feb 2017 20:25:00 +0000 (20:25 +0000)]
serial: 8250_pci: Add MKS Tenta SCOM-0800 and SCOM-0801 cards
The MKS Instruments SCOM-0800 and SCOM-0801 cards (originally by Tenta
Technologies) are 3U CompactPCI serial cards with 4 and 8 serial ports,
respectively. The first 4 ports are implemented by an OX16PCI954 chip,
and the second 4 ports are implemented by an OX16C954 chip on a local
bus, bridged by the second PCI function of the OX16PCI954. The ports
are jumper-selectable as RS-232 and RS-422/485, and the UARTs use a
non-standard oscillator frequency of 20 MHz (base_baud = 1250000).
Ulrich Hecht [Fri, 3 Feb 2017 10:38:18 +0000 (11:38 +0100)]
serial: sh-sci: SCIFA/B RX FIFO software timeout
Implements support for FIFO fill thresholds greater than one with software
timeout.
This mechanism is not possible (or at least not useful) on SCIF family
hardware other than SCIFA and SCIFB because they do not support turning off
the DR hardware timeout interrupt separately from the RI interrupt.
Rob Herring [Thu, 2 Feb 2017 19:48:09 +0000 (13:48 -0600)]
tty_port: register tty ports with serdev bus
Register a serdev controller with the serdev bus when a tty_port is
registered. This creates the serdev controller and create's serdev
devices for any DT child nodes of the tty_port's parent (i.e. the UART
device).
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-By: Sebastian Reichel <sre@kernel.org> Tested-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring [Thu, 2 Feb 2017 19:48:08 +0000 (13:48 -0600)]
serdev: add a tty port controller driver
Add a serdev controller driver for tty ports.
The controller is registered with serdev when tty ports are registered
with the TTY core. As the TTY core is built-in only, this has the side
effect of making serdev built-in as well.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-By: Sebastian Reichel <sre@kernel.org> Tested-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring [Thu, 2 Feb 2017 19:48:07 +0000 (13:48 -0600)]
serdev: Introduce new bus for serial attached devices
The serdev bus is designed for devices such as Bluetooth, WiFi, GPS
and NFC connected to UARTs on host processors. Tradionally these have
been handled with tty line disciplines, rfkill, and userspace glue such
as hciattach. This approach has many drawbacks since it doesn't fit
into the Linux driver model. Handling of sideband signals, power control
and firmware loading are the main issues.
This creates a serdev bus with controllers (i.e. host serial ports) and
attached devices. Typically, these are point to point connections, but
some devices have muxing protocols or a h/w mux is conceivable. Any
muxing is not yet supported with the serdev bus.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-By: Sebastian Reichel <sre@kernel.org> Tested-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring [Thu, 2 Feb 2017 19:48:06 +0000 (13:48 -0600)]
dt/bindings: Add a serial/UART attached device binding
Add a common binding for describing serial/UART attached devices. Common
examples are Bluetooth, WiFi, NFC and GPS devices.
Serial attached devices are represented as child nodes of a UART node.
This may need to be extended for more complex devices with multiple
interfaces, but for the simple cases a child node is sufficient.
Tested-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring [Thu, 2 Feb 2017 19:48:05 +0000 (13:48 -0600)]
tty_port: Add port client functions
Introduce a client (upward direction) operations struct for tty_port
clients. Initially supported operations are for receiving data and write
wake-up. This will allow for having clients other than an ldisc.
Convert the calls to the ldisc to use the client ops as the default
operations.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-By: Sebastian Reichel <sre@kernel.org> Tested-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ulrich Hecht [Thu, 2 Feb 2017 17:10:15 +0000 (18:10 +0100)]
serial: sh-sci: consider DR (data ready) bit adequately
To allow operation with a higher RX FIFO interrupt threshold in PIO
mode, it is necessary to consider the DR bit ("FIFO not full, but no
data received for 1.5 frames") as an indicator that data can be read.
Otherwise the driver will let data rot in the FIFO until the threshold
is reached.
Sudeep Holla [Wed, 1 Feb 2017 15:46:38 +0000 (15:46 +0000)]
tty: serial: pl011: add ttyAMA for matching pl011 console
Commit 14ccdc1563ba ("console: Add extensible console matching") added
match() method to struct console which allows the console to perform
console command line matching instead of (or in addition to) default
console matching (ie., by fixed name and index).
Commit c3c6e186fba5 ("ACPI: parse SPCR and enable matching console")
introduced support for SPCR as matching console.
Commit 756856789ea4 ("serial: pl011: add console matching function")
added the match method for pl011 console which checks for the console
string to be "pl011"
Now on a platform which has both SPCR in the ACPI tables and ttyAMA in
the command line, the ttyAMA is chosen as "selected console" but it
doesn't pass the matching console method which results in CON_CONSDEV
not being set on the "selected console".
As a result of that, the bootconsole(SPCR in the above case) is not
unregistered and all the beginning boot messages are seen twice.
This patch adds "ttyAMA" so that it's considered to match pl011 console.
남영민 [Wed, 1 Feb 2017 10:25:46 +0000 (19:25 +0900)]
serial: samsung: enable clock before accessing interrupt mask resister
Ensure that the uart clock is enabled prior to writing to the
interrupt mask register in s3c24xx_serial_resume_noirq function.
Without enabing the uart clock, the uart register cannot be accessed.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Mon, 30 Jan 2017 11:12:11 +0000 (09:12 -0200)]
serial: imx: Fix the RTS GPIO polarity in RS485 mode
On a board that needs to drive RTS GPIO high in order to enable the
transmission of a RS485 transceiver the following description is
passed in the devide tree:
/* set logical level for RTS pin equal to 1 when sending: */
rs485conf.flags |= SER_RS485_RTS_ON_SEND;
/* set logical level for RTS pin equal to 0 after sending: */
rs485conf.flags &= ~(SER_RS485_RTS_AFTER_SEND);
However the RTS GPIO polarity observed in the oscilloscope is inverted.
When the SER_RS485_RTS_ON_SEND flag is set the imx_port_rts_active()
function should be called and following the same logic when
SER_RS485_RTS_AFTER_SEND flag is cleared the imx_port_rts_inactive()
should be called.
Do such logic change so that RS485 communication in half duplex can
work successfully when the RTS GPIO pin is passed via device tree.
Arnd Bergmann [Wed, 25 Jan 2017 22:19:01 +0000 (23:19 +0100)]
8250: of: remove remnants of generic of_serial driver
During build testing, I ran into a warning in a driver that I
had written myself at some point:
drivers/tty/serial/8250/8250_of.c: In function 'of_platform_serial_probe':
drivers/tty/serial/8250/8250_of.c:233:1: error: the frame size of 1200 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
This is harmless by itself, but it shows two other problems in
the driver:
- It still tries to be generic enough to handle all kinds of serial
ports, where in reality the driver has been 8250-only for a while,
and every other uart has its own DT support
- As a result of that generalization, we keep two copies of
'struct uart_port' on the stack during probe(). This is completely
unnessary.
Removing the last code dealing with unsupported port_type values
solves both problems nicely, and reduces the stack size.
serial: sh-sci: Reformat sci_parse_dt() for git diff
As the function header of sci_parse_dt() is split in an unusual way,
"git diff" gets confused when changes to the body of the function are
made, and attributes them to the wrong function.
Bhumika Goyal [Wed, 25 Jan 2017 17:48:52 +0000 (23:18 +0530)]
tty: serial: constify uart_ops structures
Declare uart_ops structures as const as they are only stored in the ops
field of an uart_port structure. This field is of type const, so
uart_ops structures having this property can be made const too.
File size details before and after patching.
First line of every .o file shows the file size before patching
and second line shows the size after patching.
Manuel Schölling [Fri, 13 Jan 2017 20:07:58 +0000 (21:07 +0100)]
console: Make persistent scrollback a boot parameter
The impact of the persistent scrollback feature on the code size is
rather small, so the config option is removed. The feature stays
disabled by default and can be enabled by using the boot command line
parameter 'vgacon.scrollback_persistent=1' or by setting
VGACON_SOFT_SCROLLBACK_PERSISTENT_ENABLE_BY_DEFAULT=y.
Manuel Schölling [Fri, 13 Jan 2017 20:07:57 +0000 (21:07 +0100)]
console: Add persistent scrollback buffers for all VGA consoles
Add a scrollback buffers for each VGA console. The benefit is that
the scrollback history is not flushed when switching between consoles
but is persistent.
The buffers are allocated on demand when a new console is opened.
This breaks tools like clear_console that rely on flushing the
scrollback history by switching back and forth between consoles
which is why this feature is disabled by default.
Use the escape sequence \e[3J instead for flushing the buffer.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de> Reviewed-by: Andrey Utkin <andrey_utkin@fastmail.com> Tested-by: Andrey Utkin <andrey_utkin@fastmail.com> Tested-by: Adam Borowski <kilobyte@angband.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manuel Schölling [Fri, 13 Jan 2017 20:07:56 +0000 (21:07 +0100)]
console: Add callback to flush scrollback buffer to consw struct
This new callback is in preparation for persistent scrollback buffer
support for VGA consoles.
With a single scrollback buffer for all consoles, we could flush the
buffer just by invocating consw->con_switch(). But when each VGA console
has its own scrollback buffer, we need a new callback to tell the
video console driver which buffer to flush.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de> Reviewed-by: Andrey Utkin <andrey_utkin@fastmail.com> Tested-by: Andrey Utkin <andrey_utkin@fastmail.com> Tested-by: Adam Borowski <kilobyte@angband.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren [Fri, 20 Jan 2017 20:22:31 +0000 (12:22 -0800)]
serial: 8250_omap: Fix probe and remove for PM runtime
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 678329a369f6 ("tty: serial: Add 8250-core based omap driver") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Sun, 22 Jan 2017 03:08:25 +0000 (22:08 -0500)]
serial: hp300: mask the warning for people just doing build coverage
Currently this warning is triggered for allmodconfig on m68k. It is
well intentioned, in that if you are building the driver but not
enabling one of the platforms where the hardware exists, you get a
warning.
The warning dates back to pre-git days, and now we have COMPILE_TEST
so we can use that to mask the warning for people who are obviously
just doing build coverage on tree wide changes.
Yasir-Khan [Mon, 23 Jan 2017 12:26:08 +0000 (13:26 +0100)]
serial: xuartps: Enable uart loopback mode
This patch adds xilinx uart loopback support by modifying the
cdns_uart_set_mctrl function to handle the switch to loopback mode.
After this patch, the loopback mode can be enabled/disabled by
setting/clearing the TIOCM_LOOP modem bit via TIOCMBIS/TIOCMBIC
ioctls respectively.
Vignesh R [Fri, 20 Jan 2017 08:16:54 +0000 (13:46 +0530)]
serial: 8250_omap: Remove rx_dma_broken flag
8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vignesh R [Fri, 20 Jan 2017 08:16:53 +0000 (13:46 +0530)]
serial: 8250_omap: Add OMAP_DMA_TX_KICK quirk for AM437x
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vignesh R [Fri, 20 Jan 2017 08:16:52 +0000 (13:46 +0530)]
serial: 8250_omap: pause DMA only if DMA transfer in progress
It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring [Mon, 16 Jan 2017 22:54:30 +0000 (16:54 -0600)]
tty_port: make tty_port_register_device wrap tty_port_register_device_attr
tty_register_device is just a wrapper for tty_register_device_attr with
NULL passed for drvdata and attr_grp. So similarly make
tty_port_register_device a wrapper of tty_port_register_device_attr so that
additions don't have to be made in both functions.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Mon, 16 Jan 2017 22:54:29 +0000 (16:54 -0600)]
tty_port: allow a port to be opened with a tty that has no file handle
Let us create tty objects entirely in kernel space. Untested proposal to
show why all the ideas around rewriting half the uart stack are not needed.
With this a kernel created non file backed tty object could be used to handle
data, and set terminal modes. Not all ldiscs can cope with this as N_TTY in
particular has to work back to the fs/tty layer.
The tty_port code is however otherwise clean of file handles as far as I can
tell as is the low level tty port write path used by the ldisc, the
configuration low level interfaces and most of the ldiscs.
Currently you don't have any exposure to see tty hangups because those are
built around the file layer. However a) it's a fixed port so you probably
don't care about that b) if you do we can add a callback and c) you almost
certainly don't want the userspace tear down/rebuild behaviour anyway.
This should however be sufficient if we wanted for example to enumerate all
the bluetooth bound fixed ports via ACPI and make them directly available.
It doesn't deal with the case of a user opening a port that's also kernel
opened and that would need some locking out (so it returned EBUSY if bound
to a kernel device of some kind). That needs resolving along with how you
"up" or "down" your new bluetooth device, or enumerate it while providing
the existing tty API to avoid regressions (and to debug).
Signed-off-by: Alan Cox <alan@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: meson: allow baud-rates higher than 115200
The vendor driver allows setting baud-rates higher than 115200 baud.
There is a check in the vendor driver which prevents using more than
115200 baud during startup, however it does not have such a check in
.set_termios.
Higher baud-rates are often used by the bluetooth modules embedded into
the SDIO wifi chips (Amlogic devices use brcmfmac based wifi chips quite
often, 2000000 baud seems to be a common value for the UART baud-rate in
Amlogic's "libbt").
I have tested this on a Meson GXL device with uart_A (to which the
bluetooth module is connected, where initialization times out with
115200 baud) and uart_AO (which I manually set to 2000000 baud and then
connected with my USB UART adapter to that).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Herring [Mon, 16 Jan 2017 22:54:28 +0000 (16:54 -0600)]
tty: move the non-file related parts of tty_release to new tty_release_struct
For in-kernel tty users, we need to be able to create and destroy
'struct tty' that are not associated with a file. The creation side is
fine, but tty_release() needs to be split into the file handle portion
and the struct tty portion. Introduce a new function, tty_release_struct,
to handle just the destroying of a struct tty.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-By: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arvind Yadav [Thu, 19 Jan 2017 08:00:44 +0000 (13:30 +0530)]
tty: serial: 8250: 8250_gsc:- Handle return NULL error from ioremap_nocache
Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Lokesh Vutla [Thu, 19 Jan 2017 09:59:38 +0000 (15:29 +0530)]
serial: omap: Add omapserial earlycon
Add DT earlycon for omap_serial driver. This boot console is included
with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y, CONFIG_SERIAL_OMAP=y, and
CONFIG_OF_EARLY_FLATTREE=y.
This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart.
Bhumika Goyal [Sun, 15 Jan 2017 11:00:30 +0000 (16:30 +0530)]
tty: serial: constify dev_pm_ops structures
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for blackfin architecture.
File size before:
text data bss dec hex filename
3572 320 16 3908 f44 tty/serial/bfin_sport_uart.o
File size after:
text data bss dec hex filename
3664 228 16 3908 f44 tty/serial/bfin_sport_uart.o
Andy Shevchenko [Wed, 11 Jan 2017 14:31:37 +0000 (16:31 +0200)]
serial: 8250_mid: set PCI master only for DMA capable device
There is no need to set PCI bus mastering when device is not doing any DMA. It
includes MSI type of interrupts. Currently only UART on Denverton, which is DMA
capable, might have MSI enabled.
Taking above into account enable bus mastering for Denverton case only.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Wed, 11 Jan 2017 14:31:35 +0000 (16:31 +0200)]
serial: 8250_mid: handle interrupt correctly in DMA case
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
Jason Uy [Wed, 11 Jan 2017 19:48:20 +0000 (11:48 -0800)]
serial: 8250_dw: Allow hardware flow control to be used
In the most common use case, the Synopsys DW UART driver does not
set the set_termios callback function. This prevents UPSTAT_AUTOCTS
from being set when the UART flag CRTSCTS is set. As a result, the
driver will use software flow control as opposed to hardware flow
control.
To fix the problem, the set_termios callback function is set to the
DW specific function. The logic to set UPSTAT_AUTOCTS is moved so
that any clock error will not affect setting the hardware flow
control.
Reviewed-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Jason Uy <jason.uy@broadcom.com> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart [Wed, 11 Jan 2017 14:43:40 +0000 (16:43 +0200)]
serial: sh-sci: Compute the regshift value for SCI ports
SCI instances found in SH SoCs have different spacing between registers
depending on the SoC. The platform data contains a regshift field that
tells the driver by how many bits to shift the register offset to
compute its address. We can compute the regshift value automatically
based on the memory resource size, there's no need to pass the value
through platform data.
Fix the sh7750 SCI and sh7760 SIM port memory resources length to ensure
proper computation of the regshift value.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:38 +0000 (16:43 +0200)]
serial: sh-sci: Remove manual break debouncing
The sh-sci driver implements manual break debouncing for a few SH
platforms by reading the value of the RX pin port register. This feature
is optional and the driver considers all negative or zero values of the
platform data port_reg field as invalid. As the four platforms that set
the field to a register address all use an address higher than
0x7fffffff, the driver will always consider the value as invalid and
never perform debouncing. The feature is unused, remove it.
Debouncing could be implemented properly in the future using the pinctrl
and GPIO APIs if desired.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:37 +0000 (16:43 +0200)]
serial: sh-sci: Remove the platform data dma slave rx/tx channel IDs
Only SH platforms still use platform data for the sh-sci, and none of
them declare DMA channels connected to the SCI. Remove the corresponding
platform data fields and simplify the driver accordingly.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:36 +0000 (16:43 +0200)]
serial: sh-sci: Extend sci_port_params with more port parameters
The fifo size, overrun register and mask, sampling rate mask and error
mask all depend on the port type only and don't need to be computed at
runtime. Add them to the sci_port_parameters structure.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:34 +0000 (16:43 +0200)]
serial: sh-sci: Replace regmap array with port parameters
Turn the regmap two-dimensional array to an array of port parameters and
store a pointer to the port parameters in the sci_port structure. This
will allow handling additional port type dependent parameters.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:32 +0000 (16:43 +0200)]
serial: sh-sci: Fix register offsets for the IRDA serial port
Even though most of its registers are 8-bit wide, the IRDA has two
16-bit registers that make it a 16-bit peripheral and not a 8-bit
peripheral with addresses shifted by one. Fix the registers offset in
the driver and the platform data regshift value.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:30 +0000 (16:43 +0200)]
sh: Don't set the sh-sci platform data scscr CKE0 bit
The bit is only set by platforms that also set the CKE1 but, in which
case its value is ignored by the device. Don't set it, this simplifies
platform data and only leaves the CKE1 bit to be handled.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:29 +0000 (16:43 +0200)]
sh: Don't set sh-sci port_reg
The driver considers all negative or zero values of the port_reg field
as invalid. The four platforms that set the field to a register address
all use an address higher than 0x7fffffff, which is thus considered by
the driver as invalid. The feature is thus never used, remove it.
The feature could be implemented properly in the future using the
pinctrl and GPIO APIs if desired.
While at it, don't set the field to SCIx_NOT_SUPPORTED (-1) either,
leaving it unset leads to the same result. This will allow removing the
SCIx_NOT_SUPPORTED macro.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:26 +0000 (16:43 +0200)]
sh: Don't set sh-sci pdata scscr TIE and RIE bits
The scscr platform data field is used by the driver in three locations.
One of them masks out all bits except SCSCR_REIE. The two other are the
set_termios handler and the console write handler.
The set_termios handler calls sci_start_rx() to enable the receiver,
which sets the RIE bit unconditionally. It then calls sci_port_disable()
that effectively disables both the transmitter and the receiver. The
TIE bit will thus get set later when the serial cores reenables the
serial port.
The console write handler runs with interrupts disabled, and saves and
restores the SCSCR register value. The RIE and TIE bits are thus not
needed there.
The bits are thus not necessary in platform data, remove them.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:24 +0000 (16:43 +0200)]
serial: sh-sci: Don't rely on platform data flags when not needed
The UPF_BOOT_AUTOCONF platform data flag is set by all platforms,
hardcode it.
The UPF_IOREMAP flag is set by a single SH platform and thus needs to be
kept. However, for ARM platforms, we can base the decision on whether an
OF node is present and bypass the platform data flags completely.
Laurent Pinchart [Wed, 11 Jan 2017 14:43:23 +0000 (16:43 +0200)]
serial: sh-sci: Set the SCSCR TE and RE bits in the driver
The Transmit Enable and Receive Enable bits are set in the scscr field
of all instances of the sh-sci platform data. Set them in the driver
directly to prepare for their removal from platform data.
Linus Torvalds [Mon, 16 Jan 2017 00:09:50 +0000 (16:09 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"This tree contains 4 fixes.
The first is a fix for a race that can causes oopses under the right
circumstances, and that someone just recently encountered.
Past that are several small trivial correct fixes. A real issue that
was blocking development of an out of tree driver, but does not appear
to have caused any actual problems for in-tree code. A potential
deadlock that was reported by lockdep. And a deadlock people have
experienced and took the time to track down caused by a cleanup that
removed the code to drop a reference count"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Drop reference added by grab_header in proc_sys_readdir
pid: fix lockdep deadlock warning due to ucount_lock
libfs: Modify mount_pseudo_xattr to be clear it is not a userspace mount
mnt: Protect the mountpoint hashtable with mount_lock
Linus Torvalds [Sun, 15 Jan 2017 20:40:53 +0000 (12:40 -0800)]
Merge tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for 4.10-rc4 that resolve
some reported issues.
The MEI driver issue resolves a lot of problems that people have been
having, as does the mem driver fix. The other minor fixes resolve
other reported issues.
All of these have been in linux-next for a while"
* tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
vme: Fix wrong pointer utilization in ca91cx42_slave_get
auxdisplay: fix new ht16k33 build errors
ppdev: don't print a free'd string
extcon: return error code on failure
drivers: char: mem: Fix thinkos in kmem address checks
mei: bus: enable OS version only for SPT and newer
Linus Torvalds [Sun, 15 Jan 2017 20:38:53 +0000 (12:38 -0800)]
Merge tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single patch being reverted to remove a feature that was
added in 4.10-rc1 that isn't quite ready for release.
It will be redone as a debugfs file instead of a sysfs file in the
future"
* tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Revert "driver core: Add deferred_probe attribute to devices in sysfs"
Linus Torvalds [Sun, 15 Jan 2017 20:34:35 +0000 (12:34 -0800)]
Merge tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few small USB driver fixes for 4.10-rc4 to resolve some
reported issues.
The "largest" here is a number of bugs being fixed in the ch341
usb-serial driver, to hopefully resolve the mess of different devices
floating around that use this driver that have been having problems
with the 4.10-rc1 release.
There's also a tiny musb fix that I missed in the last pull request,
as well as the traditional xhci fix rounding out the batch.
All have been in linux-next with no reported issues"
* tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: fix deadlock at host remove by running watchdog correctly
USB: serial: ch341: fix control-message error handling
usb: musb: fix runtime PM in debugfs
wusbcore: Fix one more crypto-on-the-stack bug
USB: serial: kl5kusb105: fix line-state error handling
USB: serial: ch341: fix baud rate and line-control handling
USB: serial: ch341: fix line settings after reset-resume
USB: serial: ch341: fix resume after reset
USB: serial: ch341: fix open error handling
USB: serial: ch341: fix modem-control and B0 handling
USB: serial: ch341: fix open and resume after B0
USB: serial: ch341: fix initial modem-control state
Linus Torvalds [Sun, 15 Jan 2017 20:28:14 +0000 (12:28 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Bugfixes for I2C. Mostly core this time which is a bit unusual but
nothing really scary in there"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: piix4: Avoid race conditions with IMC
i2c: fix spelling mistake: "insufficent" -> "insufficient"
i2c: print correct device invalid address
i2c: do not enable fall back to Host Notify by default
i2c: fix kernel memory disclosure in dev interface
Linus Torvalds [Sun, 15 Jan 2017 20:03:11 +0000 (12:03 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- unwinder fixes
- AMD CPU topology enumeration fixes
- microcode loader fixes
- x86 embedded platform fixes
- fix for a bootup crash that may trigger when clearcpuid= is used
with invalid values"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mpx: Use compatible types in comparison to fix sparse error
x86/tsc: Add the Intel Denverton Processor to native_calibrate_tsc()
x86/entry: Fix the end of the stack for newly forked tasks
x86/unwind: Include __schedule() in stack traces
x86/unwind: Disable KASAN checks for non-current tasks
x86/unwind: Silence warnings for non-current tasks
x86/microcode/intel: Use correct buffer size for saving microcode data
x86/microcode/intel: Fix allocation size of struct ucode_patch
x86/microcode/intel: Add a helper which gives the microcode revision
x86/microcode: Use native CPUID to tickle out microcode revision
x86/CPU: Add native CPUID variants returning a single datum
x86/boot: Add missing declaration of string functions
x86/CPU/AMD: Fix Bulldozer topology
x86/platform/intel-mid: Rename 'spidev' to 'mrfld_spidev'
x86/cpu: Fix typo in the comment for Anniedale
x86/cpu: Fix bootup crashes by sanitizing the argument of the 'clearcpuid=' command-line option
Linus Torvalds [Sun, 15 Jan 2017 20:00:37 +0000 (12:00 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull NOHZ fix from Ingo Molnar:
"This fixes an old NOHZ race where we incorrectly calculate the next
timer interrupt in certain circumstances where hrtimers are pending,
that can cause hard to reproduce stalled-values artifacts in
/proc/stat"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix collision between tick and other hrtimers
Linus Torvalds [Sun, 15 Jan 2017 19:37:43 +0000 (11:37 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc race fixes uncovered by fuzzing efforts, a Sparse fix, two PMU
driver fixes, plus miscellanous tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Reject non sampling events with precise_ip
perf/x86/intel: Account interrupts for PEBS errors
perf/core: Fix concurrent sys_perf_event_open() vs. 'move_group' race
perf/core: Fix sys_perf_event_open() vs. hotplug
perf/x86/intel: Use ULL constant to prevent undefined shift behaviour
perf/x86/intel/uncore: Fix hardcoded socket 0 assumption in the Haswell init code
perf/x86: Set pmu->module in Intel PMU modules
perf probe: Fix to probe on gcc generated symbols for offline kernel
perf probe: Fix --funcs to show correct symbols for offline module
perf symbols: Robustify reading of build-id from sysfs
perf tools: Install tools/lib/traceevent plugins with install-bin
tools lib traceevent: Fix prev/next_prio for deadline tasks
perf record: Fix --switch-output documentation and comment
perf record: Make __record_options static
tools lib subcmd: Add OPT_STRING_OPTARG_SET option
perf probe: Fix to get correct modname from elf header
samples/bpf trace_output_user: Remove duplicate sys/ioctl.h include
samples/bpf sock_example: Avoid getting ethhdr from two includes
perf sched timehist: Show total scheduling time
Linus Torvalds [Sun, 15 Jan 2017 18:54:39 +0000 (10:54 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"A number of regression fixes:
- Fix a boot hang on machines that have somewhat unusual memory map
entries of phys_addr=0x0 num_pages=0, which broke due to a recent
commit. This commit got cherry-picked from the v4.11 queue because
the bug is affecting real machines.
- Fix a boot hang also reported by KASAN, caused by incorrect init
ordering introduced by a recent optimization.
- Fix a recent robustification fix to allocate_new_fdt_and_exit_boot()
that introduced an invalid assumption. Neither bugs were seen in
the wild AFAIK"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Prune invalid memory map entries and fix boot regression
x86/efi: Don't allocate memmap through memblock after mm_init()
efi/libstub/arm*: Pass latest memory map to the kernel
Linus Torvalds [Sun, 15 Jan 2017 01:13:28 +0000 (17:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro.
The most notable fix here is probably the fix for a splice regression
("fix a fencepost error in pipe_advance()") noticed by Alan Wylie.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a fencepost error in pipe_advance()
coredump: Ensure proper size of sparse core files
aio: fix lock dep warning
tmpfs: clear S_ISGID when setting posix ACLs
Linus Torvalds [Sun, 15 Jan 2017 01:07:04 +0000 (17:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- the virtio_blk stack DMA corruption fix from Christoph, fixing and
issue with VMAP stacks.
- O_DIRECT blkbits calculation fix from Chandan.
- discard regression fix from Christoph.
- queue init error handling fixes for nbd and virtio_blk, from Omar and
Jeff.
- two small nvme fixes, from Christoph and Guilherme.
- rename of blk_queue_zone_size and bdev_zone_size to _sectors instead,
to more closely follow what we do in other places in the block layer.
This interface is new for this series, so let's get the naming right
before releasing a kernel with this feature. From Damien.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't try to discard from __blkdev_issue_zeroout
sd: remove __data_len hack for WRITE SAME
nvme: use blk_rq_payload_bytes
scsi: use blk_rq_payload_bytes
block: add blk_rq_payload_bytes
block: Rename blk_queue_zone_size and bdev_zone_size
nvme: apply DELAY_BEFORE_CHK_RDY quirk at probe time too
nvme-rdma: fix nvme_rdma_queue_is_ready
virtio_blk: fix panic in initialization error path
nbd: blk_mq_init_queue returns an error code on failure, not NULL
virtio_blk: avoid DMA to stack for the sense buffer
do_direct_IO: Use inode->i_blkbits to compute block count to be cleaned