Ondrej Zary [Sat, 25 Sep 2010 10:39:17 +0000 (10:39 +0000)]
de2104x: fix TP link detection
Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Fri, 24 Sep 2010 23:57:02 +0000 (23:57 +0000)]
de2104x: fix power management
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Thu, 23 Sep 2010 10:59:18 +0000 (10:59 +0000)]
de2104x: disable autonegotiation on broken hardware
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Sep 2010 12:43:39 +0000 (12:43 +0000)]
net: fix a lockdep splat
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Jarek Poplawski <jarkao2@gmail.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:17:01 +0000 (17:17 +0000)]
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:16:18 +0000 (17:16 +0000)]
e1000e: 82579 unaccounted missed packets
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
CC: stable@kernel.org Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:15:33 +0000 (17:15 +0000)]
e1000e: 82579 SMBus address and LEDs incorrect after device reset
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 22 Sep 2010 17:15:08 +0000 (17:15 +0000)]
e1000e: 82577/8/9 issues with device in Sx
When going to Sx, disable gigabit in PHY (e1000_oem_bits_config_ich8lan)
in addition to the MAC before configuring PHY wakeup otherwise the PHY
configuration writes might be missed. Also write the LED configuration
and SMBus address to the PHY registers (e1000_oem_bits_config_ich8lan and
e1000_write_smbus_addr, respectively). The reset is no longer needed
since re-auto-negotiation is forced in e1000_oem_bits_config_ich8lan and
leaving it in causes issues with auto-negotiating the link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1: zero out CMB and SBM in atl1_free_ring_resources
They are allocated in atl1_setup_ring_resources, zero out the pointers
in atl1_free_ring_resources (like the other resources).
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Acked-by: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->cmb.cmb is initialized when the device is opened and freed when
it's closed. Accessing it unconditionally during resume results either
in a crash (NULL pointer dereference, when the interface has not been
opened yet) or data corruption (when the interface has been used and
brought down adapter->cmb.cmb points to a deallocated memory area).
Cc: stable@kernel.org Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Acked-by: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Move "struct net" declaration inside the __KERNEL__ macro guard
This patch reduces namespace pollution by moving the "struct net" declaration
out of the userspace-facing portion of linux/netlink.h. It has no impact on
the kernel.
(This came up because we have several C++ applications which use "net" as a
namespace name.)
Signed-off-by: Ollie Wild <aaw@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Olsa [Tue, 21 Sep 2010 21:17:34 +0000 (21:17 +0000)]
netfilter: nf_conntrack_defrag: check socket type before touching nodefrag flag
we need to check proper socket type within ipv4_conntrack_defrag
function before referencing the nodefrag flag.
For example the tun driver receive path produces skbs with
AF_UNSPEC socket type, and so current code is causing unwanted
fragmented packets going out.
Signed-off-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Sep 2010 21:17:32 +0000 (21:17 +0000)]
netfilter: fix a race in nf_ct_ext_create()
As soon as rcu_read_unlock() is called, there is no guarantee current
thread can safely derefence t pointer, rcu protected.
Fix is to copy t->alloc_size in a temporary variable.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: fix ipt_REJECT TCP RST routing for indev == outdev
ip_route_me_harder can't create the route cache when the outdev is the same
with the indev for the skbs whichout a valid protocol set.
__mkroute_input functions has this check:
1998 if (skb->protocol != htons(ETH_P_IP)) {
1999 /* Not IP (i.e. ARP). Do not create route, if it is
2000 * invalid for proxy arp. DNAT routes are always valid.
2001 *
2002 * Proxy arp feature have been extended to allow, ARP
2003 * replies back to the same interface, to support
2004 * Private VLAN switch technologies. See arp.c.
2005 */
2006 if (out_dev == in_dev &&
2007 IN_DEV_PROXY_ARP_PVLAN(in_dev) == 0) {
2008 err = -EINVAL;
2009 goto cleanup;
2010 }
2011 }
This patch gives the new skb a valid protocol to bypass this check. In order
to make ipt_REJECT work with bridges, you also need to enable ip_forward.
This patch also fixes a regression. When we used skb_copy_expand(), we
didn't have this issue stated above, as the protocol was properly set.
Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Tue, 21 Sep 2010 21:17:30 +0000 (21:17 +0000)]
netfilter: nf_ct_sip: default to NF_ACCEPT in sip_help_tcp()
I initially noticed this because of the compiler warning below, but it
does seem to be a valid concern in the case where ct_sip_get_header()
returns 0 in the first iteration of the while loop.
net/netfilter/nf_conntrack_sip.c: In function 'sip_help_tcp':
net/netfilter/nf_conntrack_sip.c:1379: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Simon Horman <horms@verge.net.au>
[Patrick: changed NF_DROP to NF_ACCEPT] Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Sep 2010 21:17:29 +0000 (21:17 +0000)]
netfilter: tproxy: nf_tproxy_assign_sock() can handle tw sockets
transparent field of a socket is either inet_twsk(sk)->tw_transparent
for timewait sockets, or inet_sk(sk)->transparent for other sockets
(TCP/UDP).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 21 Sep 2010 08:47:45 +0000 (08:47 +0000)]
ip: fix truesize mismatch in ip fragmentation
Special care should be taken when slow path is hit in ip_fragment() :
When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.
Many thanks to Nick Bowler, who provided a very clean bug report and
test program.
Thanks to Jarek for reviewing my first patch and providing a V2
While Nick bisection pointed to commit 8514b872147 (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)
A side effect is to extend work done in commit 1b481175ac944d
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com> Tested-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Jarek Poplawski <jarkao2@gmail.com> CC: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Marshall [Mon, 20 Sep 2010 22:42:05 +0000 (15:42 -0700)]
tcp: Fix race in tcp_poll
If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT. Fix this by checking sk->sk_err at the end
of tcp_poll. Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: Tom Marshall <tdm.code@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Egerer [Mon, 20 Sep 2010 18:11:38 +0000 (11:11 -0700)]
xfrm: Allow different selector family in temporary state
The family parameter xfrm_state_find is used to find a state matching a
certain policy. This value is set to the template's family
(encap_family) right before xfrm_state_find is called.
The family parameter is however also used to construct a temporary state
in xfrm_state_find itself which is wrong for inter-family scenarios
because it produces a selector for the wrong family. Since this selector
is included in the xfrm_user_acquire structure, user space programs
misinterpret IPv6 addresses as IPv4 and vice versa.
This patch splits up the original init_tempsel function into a part that
initializes the selector respectively the props and id of the temporary
state, to allow for differing ip address families whithin the state.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver doesn't fill the entire buffer, old
heap contents may remain, and if it also doesn't
update the length properly, this old heap content
will be copied back to userspace.
It is very unlikely that this happens in any of
the drivers using private ioctls since it would
show up as junk being reported by iwpriv, but it
seems better to be safe here, so use kzalloc.
Reported-by: Jeff Mahoney <jeffm@suse.com> Cc: stable@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
dca: disable dca on IOAT ver.3.0 multiple-IOH platforms
Direct Cache Access is not supported on IOAT ver.3.0 multiple-IOH platforms.
This patch blocks registering of dca providers when multiple IOH detected with IOAT ver.3.0.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 17 Sep 2010 23:55:03 +0000 (16:55 -0700)]
netpoll: Disable IRQ around RCU dereference in netpoll_rx
We cannot use rcu_dereference_bh safely in netpoll_rx as we may
be called with IRQs disabled. We could however simply disable
IRQs as that too causes BH to be disabled and is safe in either
case.
Thanks to John Linville for discovering this bug and providing
a patch.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp: Do not reset the packet during sctp_packet_config().
sctp_packet_config() is called when getting the packet ready
for appending of chunks. The function should not touch the
current state, since it's possible to ping-pong between two
transports when sending, and that can result packet corruption
followed by skb overlfow crash.
Reported-by: Thomas Dreibholz <dreibh@iem.uni-due.de> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Snook [Fri, 17 Sep 2010 05:00:28 +0000 (22:00 -0700)]
MAINTAINERS: move atlx discussions to netdev
The atlx drivers are sufficiently mature that we no longer need a separate
mailing list for them. Move the discussion to netdev, so we can decommission
atl1-devel, which is now mostly spam.
Signed-off-by: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The CHELSIO_GET_QSET_NUM device ioctl allows unprivileged users to read
4 bytes of uninitialized stack memory, because the "addr" member of the
ch_reg struct declared on the stack in cxgb_extension_ioctl() is not
altered or zeroed before being copied back to the user. This patch
takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The EQL_GETMASTRCFG device ioctl allows unprivileged users to read 16
bytes of uninitialized stack memory, because the "master_name" member of
the master_config_t struct declared on the stack in eql_g_master_cfg()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The TIOCGICOUNT device ioctl allows unprivileged users to read
uninitialized stack memory, because the "reserved" member of the
serial_icounter_struct struct declared on the stack in hso_get_count()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 16 Sep 2010 12:27:50 +0000 (12:27 +0000)]
xfrm: dont assume rcu_read_lock in xfrm_output_one()
ip_local_out() is called with rcu_read_lock() held from ip_queue_xmit()
but not from other call sites.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Garrett [Tue, 14 Sep 2010 11:57:11 +0000 (11:57 +0000)]
r8169: Handle rxfifo errors on 8168 chips
The Thinkpad X100e seems to have some odd behaviour when the display is
powered off - the onboard r8169 starts generating rxfifo overflow errors.
The root cause of this has not yet been identified and may well be a
hardware design bug on the platform, but r8169 should be more resiliant to
this. This patch enables the rxfifo interrupt on 8168 devices and removes
the MAC version check in the interrupt handler, and the machine no longer
crashes when under network load while the screen turns off.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vortex_set_wol protected with a spinlock, but nested acpi_set_WOL acquires a mutex inside atomic context.
Ethtool operations are already serialized by RTNL mutex, so it is safe to drop the locks.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: Prevent overzealous packetization by SWS logic.
If peer uses tiny MSS (say, 75 bytes) and similarly tiny advertised
window, the SWS logic will packetize to half the MSS unnecessarily.
This causes problems with some embedded devices.
However for large MSS devices we do want to half-MSS packetize
otherwise we never get enough packets into the pipe for things
like fast retransmit and recovery to work.
Be careful also to handle the case where MSS > window, otherwise
we'll never send until the probe timer.
Reported-by: ツ Leandro Melo de Sales <leandroal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Guinot [Mon, 13 Sep 2010 22:12:01 +0000 (22:12 +0000)]
phylib: fix PAL state machine restart on resume
On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.
This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 13 Sep 2010 12:24:54 +0000 (12:24 +0000)]
net: use rcu_barrier() in rollback_registered_many
netdev_wait_allrefs() waits that all references to a device vanishes.
It currently uses a _very_ pessimistic 250 ms delay between each probe.
Some users reported that no more than 4 devices can be dismantled per
second, this is a pretty serious problem for some setups.
Most of the time, a refcount is about to be released by an RCU callback,
that is still in flight because rollback_registered_many() uses a
synchronize_rcu() call instead of rcu_barrier(). Problem is visible if
number of online cpus is one, because synchronize_rcu() is then a no op.
time to remove 50 ipip tunnels on a UP machine :
before patch : real 11.910s
after patch : real 1.250s
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reported-by: Octavian Purdila <opurdila@ixiacom.com> Reported-by: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Fri, 10 Sep 2010 11:43:20 +0000 (11:43 +0000)]
bonding: correctly process non-linear skbs
It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there. That explained the inability to form an
802.3ad-based bond. For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.
This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.
Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: stable@kerne.org Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In mergeable buffer case, we use headcount, log_num
and seg as indexes in same-size arrays, and
we know that headcount <= seg and
log_num equals either 0 or seg.
Therefore, the right thing to do is range-check seg,
not headcount as we do now: these will be different
if guest chains s/g descriptors (this does not
happen now, but we can not trust the guest).
Long term, we should add BUG_ON checks to verify
two other indexes are what we think they should be.
Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Michael Kerrisk [Fri, 10 Sep 2010 20:26:56 +0000 (20:26 +0000)]
ipv4: enable getsockopt() for IP_NODEFRAG
While integrating your man-pages patch for IP_NODEFRAG, I noticed
that this option is settable by setsockopt(), but not gettable by
getsockopt(). I suppose this is not intended. The (untested,
trivial) patch below adds getsockopt() support.
Signed-off-by: Michael kerrisk <mtk.manpages@gmail.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bob Arendt [Mon, 13 Sep 2010 19:56:03 +0000 (12:56 -0700)]
ipv4: force_igmp_version ignored when a IGMPv3 query received
After all these years, it turns out that the
/proc/sys/net/ipv4/conf/*/force_igmp_version
parameter isn't fully implemented.
*Symptom*:
When set force_igmp_version to a value of 2, the kernel should only perform
multicast IGMPv2 operations (IETF rfc2236). An host-initiated Join message
will be sent as a IGMPv2 Join message. But if a IGMPv3 query message is
received, the host responds with a IGMPv3 join message. Per rfc3376 and
rfc2236, a IGMPv2 host should treat a IGMPv3 query as a IGMPv2 query and
respond with an IGMPv2 Join message.
*Consequences*:
This is an issue when a IGMPv3 capable switch is the querier and will only
issue IGMPv3 queries (which double as IGMPv2 querys) and there's an
intermediate switch that is only IGMPv2 capable. The intermediate switch
processes the initial v2 Join, but fails to recognize the IGMPv3 Join responses
to the Query, resulting in a dropped connection when the intermediate v2-only
switch times it out.
*Identifying issue in the kernel source*:
The issue is in this section of code (in net/ipv4/igmp.c), which is called when
an IGMP query is received (from mainline 2.6.36-rc3 gitweb):
...
A IGMPv3 query has a length >= 12 and no sources. This routine will exit after
line 880, setting the general query timer (random timeout between 0 and query
response time). This calls igmp_gq_timer_expire():
...
.. which only sends a v3 response. So if a v3 query is received, the kernel
always sends a v3 response.
IGMP queries happen once every 60 sec (per vlan), so the traffic is low. A
IGMPv3 query *is* a strict superset of a IGMPv2 query, so this patch properly
short circuit's the v3 behaviour.
One issue is that this does not address force_igmp_version=1. Then again, I've
never seen any IGMPv1 multicast equipment in the wild. However there is a lot
of v2-only equipment. If it's necessary to support the IGMPv1 case as well:
837 if (len == 8 || IGMP_V2_SEEN(in_dev) || IGMP_V1_SEEN(in_dev)) {
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 10 Sep 2010 01:58:10 +0000 (01:58 +0000)]
ppp: potential NULL dereference in ppp_mp_explode()
Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line. Partly the reason this
bug was introduced is because code was too complicated. I've simplified
it a little.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 10 Sep 2010 01:56:16 +0000 (01:56 +0000)]
net/llc: make opt unsigned in llc_ui_setsockopt()
The members of struct llc_sock are unsigned so if we pass a negative
value for "opt" it can cause a sign bug. Also it can cause an integer
overflow when we multiply "opt * HZ".
CC: stable@kernel.org Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Wed, 8 Sep 2010 07:50:47 +0000 (07:50 +0000)]
ipheth: remove incorrect devtype to WWAN
The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.
As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 8 Sep 2010 05:08:44 +0000 (05:08 +0000)]
udp: add rehash on connect()
commit a415d3e7 introduced in linux-2.6.33 (udp: bind() optimisation)
added a secondary hash on UDP, hashed on (local addr, local port).
Problem is that following sequence :
fd = socket(...)
connect(fd, &remote, ...)
not only selects remote end point (address and port), but also sets
local address, while UDP stack stored in secondary hash table the socket
while its local address was INADDR_ANY (or ipv6 equivalent)
Sequence is :
- autobind() : choose a random local port, insert socket in hash tables
[while local address is INADDR_ANY]
- connect() : set remote address and port, change local address to IP
given by a route lookup.
When an incoming UDP frame comes, if more than 10 sockets are found in
primary hash table, we switch to secondary table, and fail to find
socket because its local address changed.
One solution to this problem is to rehash datagram socket if needed.
We add a new rehash(struct socket *) method in "struct proto", and
implement this method for UDP v4 & v6, using a common helper.
This rehashing only takes care of secondary hash table, since primary
hash (based on local port only) is not changed.
Reported-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Jianzhao Wang [Wed, 8 Sep 2010 21:35:43 +0000 (14:35 -0700)]
net: blackhole route should always be recalculated
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d8fe8a0fe1b4b3bdd749e2e3155183ede7cdbc83.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allow trie_firstleaf() to be called either under rcu_read_lock()
protection or with RTNL held. The same annotation is added to
node_parent_rcu() to prevent a similar warning a bit later.
Ben Hutchings [Tue, 7 Sep 2010 04:35:19 +0000 (04:35 +0000)]
niu: Fix kernel buffer overflow for ETHTOOL_GRXCLSRLALL
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- Do not create expectation when forwarding the PORT
command to avoid blocking the connection. The problem is that
nf_conntrack_ftp.c:help() tries to create the same expectation later in
POST_ROUTING and drops the packet with "dropping packet" message after
failure in nf_ct_expect_related.
- Change ip_vs_update_conntrack to alter the conntrack
for related connections from real server. If we do not alter the reply in
this direction the next packet from client sent to vport 20 comes as NEW
connection. We alter it but may be some collision happens for both
conntracks and the second conntrack gets destroyed immediately. The
connection stucks too.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch: "gro: fix different skb headrooms" in its part:
"2) allocate a minimal skb for head of frag_list" is buggy. The copied
skb has p->data set at the ip header at the moment, and skb_gro_offset
is the length of ip + tcp headers. So, after the change the length of
mac header is skipped. Later skb_set_mac_header() sets it into the
NET_SKB_PAD area (if it's long enough) and ip header is misaligned at
NET_SKB_PAD + NET_IP_ALIGN offset. There is no reason to assume the
original skb was wrongly allocated, so let's copy it as it was.
Reported-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> CC: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Plamen Petrov <pvp-lsts@fs.uni-ruse.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Make fiemap work with sparse files
xfs: prevent 32bit overflow in space reservation
xfs: Disallow 32bit project quota id
xfs: improve buffer cache hash scalability
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: resolve confusion of MD_CHANGE_CLEAN
md: don't clear MD_CHANGE_CLEAN in md_update_sb() for external arrays
Move .gitignore from drivers/md to lib/raid6
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix a mismatch between code and comment
percpu: fix a memory leak in pcpu_extend_area_map()
percpu: add __percpu notations to UP allocator
percpu: handle __percpu notations in UP accessors
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: wlan-ng: Explicitly set some fields in cfg80211 interface
Staging: octeon: depends on NETDEVICES
Staging: spectra: depend on X86_MRST
Staging: zram: free device memory when init fails
Staging: rt2870sta: Add more device IDs from vendor drivers
staging: comedi das08_cs.c: Fix io_req_t conversion
staging: spectra needs <linux/slab.h>
staging: hv: Fixed lockup problem with bounce_buffer scatter list
staging: hv: Increased storvsc ringbuffer and max_io_requests
staging: hv: Fixed the value of the 64bit-hole inside ring buffer
staging: hv: Fixed bounce kmap problem by using correct index
staging: hv: Fix missing functions for net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio: Added custom PIDs for ChamSys products
USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint descriptors.
USB: cdc-acm: Add pseudo modem without AT command capabilities
USB: cxacru: Use a bulk/int URB to access the command endpoint
usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.
USB: cdc-acm: Adding second ACM channel support for various Nokia and one Samsung phones
usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.
USB: ssu100: turn off debug flag
usb: allow drivers to use allocated bandwidth until unbound
USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.
USB: cp210x: Add B&G H3000 link cable ID
USB: CP210x Add new device ID
USB: option: fix incorrect novatel entries
USB: Fix kernel oops with g_ether and Windows
USB: rndis: section mismatch fix
USB: ehci-ppc-of: problems in unwind
USB: s3c-hsotg: Remove DEBUG define
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not oops when erroneous PEB is scheduled for scrubbing
UBI: fix kconfig unmet dependency
UBI: fix forward compatibility
UBI: eliminate update of list_for_each_entry loop cursor
Merge branch 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Do not force 1024x768 modes on unknown connectors
drm/kms: Add a module parameter to disable polling
drm/radeon/kms: fix tv-out on avivo asics
drm/radeon/kms/evergreen: fix gpu hangs in userspace accel code
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
drm/radeon/kms/evergreen: work around bad data in some i2c tables
drm/radeon/kms: properly set crtc high base on r7xx
drm/radeon/kms: fix tv module parameter
drm/radeon/kms: force legacy pll algo for RV515 LVDS
drm/radeon/kms: remove useless clock code
drm/radeon/kms: fix a regression on r7xx AGP due to the HDP flush fix
drm/radeon/kms: use tracked values for sclk and mclk
David S. Miller [Tue, 7 Sep 2010 05:36:19 +0000 (22:36 -0700)]
ipv4: Fix reverse path filtering with multipath routing.
Actually iterate over the next-hops to make sure we have
a device match. Otherwise RP filtering is always elided
when the route matched has multiple next-hops.
Reported-by: Igor M Podlesny <for.poige@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We assumed that unix_autobind() never fails if kzalloc() succeeded.
But unix_autobind() allows only 1048576 names. If /proc/sys/fs/file-max is
larger than 1048576 (e.g. systems with more than 10GB of RAM), a local user can
consume all names using fork()/socket()/bind().
If all names are in use, those who call bind() with addr_len == sizeof(short)
or connect()/sendmsg() with setsockopt(SO_PASSCRED) will continue
while (1)
yield();
loop at unix_autobind() till a name becomes available.
This patch adds a loop counter in order to give up after 1048576 attempts.
Calling yield() for once per 256 attempts may not be sufficient when many names
are already in use, for __unix_find_socket_byname() can take long time under
such circumstance. Therefore, this patch also adds cond_resched() call.
Note that currently a local user can consume 2GB of kernel memory if the user
is allowed to create and autobind 1048576 UNIX domain sockets. We should
consider adding some restriction for autobind operation.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a simplified version of the original patch from James Courtier-Dutton.
>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sat, 4 Sep 2010 03:14:35 +0000 (03:14 +0000)]
irda: off by one
This is an off by one. We would go past the end when we NUL terminate
the "value" string at end of the function. The "value" buffer is
allocated in irlan_client_parse_response() or
irlan_provider_parse_command().
CC: stable@kernel.org Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead. However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.
Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock. Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt(). This also removes the
potential for calling vortex_rx() on a later-generation NIC.
Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Helmut Schaa [Fri, 3 Sep 2010 02:39:56 +0000 (02:39 +0000)]
net: fix tx queue selection for bridged devices implementing select_queue
When a net device is implementing the select_queue callback and is part of
a bridge, frames coming from the bridge already have a tx queue associated
to the socket (introduced in commit a69d10ae70f37dc104e9d1d990f287122bdbf096,
"net: Use sk_tx_queue_mapping for connected sockets"). The call to
sk_tx_queue_get will then return the tx queue used by the bridge instead
of calling the select_queue callback.
In case of mac80211 this broke QoS which is implemented by using the
select_queue callback. Furthermore it introduced problems with rt2x00
because frames with the same TID and RA sometimes appeared on different
tx queues which the hw cannot handle correctly.
Fix this by always calling select_queue first if it is available and only
afterwards use the socket tx queue mapping.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).
Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.
jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reported-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 31 Aug 2010 15:52:21 +0000 (16:52 +0100)]
h8300: Fix missing consts in kernel_execve()
Fix missing consts in h8300's kernel_execve():
arch/h8300/kernel/sys_h8300.c: In function 'kernel_execve':
arch/h8300/kernel/sys_h8300.c:59: warning: initialization from incompatible pointer type
arch/h8300/kernel/sys_h8300.c:60: warning: initialization from incompatible pointer type
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 31 Aug 2010 15:52:16 +0000 (16:52 +0100)]
h8300: Fix die()
Fix h8300's die() to take care of a number of problems:
CC arch/h8300/kernel/traps.o
In file included from arch/h8300/include/asm/bitops.h:10,
from include/linux/bitops.h:22,
from include/linux/kernel.h:17,
from include/linux/sched.h:54,
from arch/h8300/kernel/traps.c:18:
arch/h8300/include/asm/system.h:136: warning: 'struct pt_regs' declared inside parameter list
arch/h8300/include/asm/system.h:136: warning: its scope is only this definition or declaration, which is probably not what you want
arch/h8300/kernel/traps.c:100: error: conflicting types for 'die'
arch/h8300/include/asm/system.h:136: error: previous declaration of 'die' was here
make[2]: *** [arch/h8300/kernel/traps.o] Error 1
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 31 Aug 2010 15:52:11 +0000 (16:52 +0100)]
h8300: IRQ flags should be stored in an unsigned long
Fix h8300's asm/atomic.h to store the IRQ flags in an unsigned long to deal
with warnings of the following type:
arch/h8300/include/asm/atomic.h: In function 'atomic_add_return':
arch/h8300/include/asm/atomic.h:22: warning: comparison of distinct pointer types lacks a cast
arch/h8300/include/asm/atomic.h:24: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / kernel.git / log