Qing Zhang [Sat, 6 Aug 2022 08:10:04 +0000 (16:10 +0800)]
LoongArch: Add STACKTRACE support
1. Use common arch_stack_walk() infrastructure to avoid duplicated code
and avoid taking care of the stack storage and filtering.
2. Add sched_ra (means sched return address) and sched_cfa (means sched
call frame address) to thread_info, and store them in switch_to().
3. Add __get_wchan() implementation.
Now we can print the process stack and wait channel by cat /proc/*/stack
and /proc/*/wchan.
Qing Zhang [Sat, 6 Aug 2022 08:10:03 +0000 (16:10 +0800)]
LoongArch: Add prologue unwinder support
It unwind the stack frame based on prologue code analyze.
CONFIG_KALLSYMS is needed, at least the address and length
of each function.
Three stages when we do unwind,
1) unwind_start(), the prapare of unwinding, fill unwind_state.
2) unwind_done(), judge whether the unwind process is finished or not.
3) unwind_next_frame(), unwind the next frame.
Dividing unwinder helps to add new unwinders in the future, e.g.:
unwinder_frame, unwinder_orc, .etc.
Qing Zhang [Sat, 6 Aug 2022 08:10:02 +0000 (16:10 +0800)]
LoongArch: Add guess unwinder support
Name "guess unwinder" comes from x86, it scans the stack and reports
every kernel text address it finds.
Unwinders can be used by dump_stack() and other stacktrace functions.
Three stages when we do unwind,
1) unwind_start(), the prapare of unwinding, fill unwind_state.
2) unwind_done(), judge whether the unwind process is finished or not.
3) unwind_next_frame(), unwind the next frame.
Add get_stack_info() to get stack info. At present we have irq stack and
task stack. The next_sp is the key info between two types of stacks.
Dividing unwinder helps to add new unwinders in the future.
Huacai Chen [Thu, 11 Aug 2022 12:52:12 +0000 (20:52 +0800)]
LoongArch: Jump to the link address before enable PG
The kernel entry points of both boot CPU (i.e., kernel_entry) and non-
boot CPUs (i.e., smpboot_entry) may be physical address from BootLoader
(in DA mode or identity-mapping PG mode). So we should jump to the link
address before PG enabled (because DA is disabled at the same time) and
just after DMW configured.
Specifically: With some older firmwares, non-boot CPUs started with PG
enabled, but this need firmware cooperation in the form of a temporary
page table, which is deemed unnecessary. OTOH, latest firmware versions
configure the non-boot CPUs to start in DA mode, so kernel-side changes
are needed.
Reviewed-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Yang Li [Sat, 6 Aug 2022 07:19:33 +0000 (15:19 +0800)]
LoongArch: Fix unsigned comparison with less than zero
The return value from the call to get_timer_irq() is int, which can be
a negative error code. However, the return value is being assigned to an
unsigned int variable 'irq', so making 'irq' an int.
Eliminate the following coccicheck warning:
./arch/loongarch/kernel/time.c:146:5-8: WARNING: Unsigned expression compared with zero: irq < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Huacai Chen [Sat, 6 Aug 2022 07:19:32 +0000 (15:19 +0800)]
LoongArch: Adjust arch/loongarch/Kconfig
1, ACPI, EFI and SMP are mandatories for LoongArch, select them
unconditionally to avoid various build errors for 'make randconfig'.
2, Move the MMU_GATHER_MERGE_VMAS selection to the correct place.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
LoongArch: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
When CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS is selected,
cpu_max_bits_warn() generates a runtime warning similar as below while
we show /proc/cpuinfo. Fix this by using nr_cpu_ids (the runtime limit)
instead of NR_CPUS to iterate CPUs.
Merge tag 'x86_urgent_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Update the 'mitigations=' kernel param documentation
- Check the IBPB feature flag before enabling IBPB in firmware calls
because cloud vendors' fantasy when it comes to creating guest
configurations is unlimited
- Unexport sev_es_ghcb_hv_call() before 5.19 releases now that HyperV
doesn't need it anymore
- Remove dead CONFIG_* items
* tag 'x86_urgent_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
docs/kernel-parameters: Update descriptions for "mitigations=" param with retbleed
x86/bugs: Do not enable IBPB at firmware entry when IBPB is not available
Revert "x86/sev: Expose sev_es_ghcb_hv_call() for use by HyperV"
x86/configs: Update configs in x86_debug.config
Merge tag 'locking_urgent_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Borislav Petkov:
- Avoid rwsem lockups in certain situations when handling the handoff
bit
* tag 'locking_urgent_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem: Allow slowpath writer to ignore handoff bit if not set by first waiter
Merge tag 'edac_urgent_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
- Relax the condition under which the DIMM label in ghes_edac is set in
order to accomodate an HPE BIOS which sets only the device but not
the bank
- Two forgotten fixes to synopsys_edac when handling error interrupts
* tag 'edac_urgent_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/ghes: Set the DIMM label unconditionally
EDAC/synopsys: Re-enable the error interrupts on v3 hw
EDAC/synopsys: Use the correct register to disable the error interrupt on v3 hw
Waiman Long [Wed, 22 Jun 2022 20:04:19 +0000 (16:04 -0400)]
locking/rwsem: Allow slowpath writer to ignore handoff bit if not set by first waiter
With commit adf56da3a439 ("locking/rwsem: Make handoff bit handling more
consistent"), the writer that sets the handoff bit can be interrupted
out without clearing the bit if the wait queue isn't empty. This disables
reader and writer optimistic lock spinning and stealing.
Now if a non-first writer in the queue is somehow woken up or a new
waiter enters the slowpath, it can't acquire the lock. This is not the
case before commit adf56da3a439 as the writer that set the handoff bit
will clear it when exiting out via the out_nolock path. This is less
efficient as the busy rwsem stays in an unlock state for a longer time.
In some cases, this new behavior may cause lockups as shown in [1] and
[2].
This patch allows a non-first writer to ignore the handoff bit if it
is not originally set or initiated by the first waiter. This patch is
shown to be effective in fixing the lockup problem reported in [1].
Fixes: adf56da3a439 ("locking/rwsem: Make handoff bit handling more consistent") Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: John Donnelly <john.p.donnelly@oracle.com> Tested-by: Mel Gorman <mgorman@techsingularity.net> Link: https://lore.kernel.org/r/20220622200419.778799-1-longman@redhat.com
Merge tag 'mm-hotfixes-stable-2022-07-29' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Two hotfixes, both cc:stable"
* tag 'mm-hotfixes-stable-2022-07-29' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/hmm: fault non-owner device private entries
page_alloc: fix invalid watermark check on a negative value
Merge tag 'drm-fixes-2022-07-30' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Dave Airlie:
"Maxime had the dog^Wmailing list server eat his homework^Wmisc pull
request.
Two more small fixes, one in nouveau svm code and the other in
simpledrm.
nouveau:
- page migration fix
simpledrm:
- fix mode_valid return value"
* tag 'drm-fixes-2022-07-30' of git://anongit.freedesktop.org/drm/drm:
nouveau/svm: Fix to migrate all requested pages
drm/simpledrm: Fix return type of simpledrm_simple_display_pipe_mode_valid()
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes, three in drivers.
The two biggest fixes are ufs and the remaining driver and core fix
are small and obvious (and the core fix is low risk)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Fix a race condition related to device management
scsi: core: Fix warning in scsi_alloc_sgtables()
scsi: ufs: host: Hold reference returned by of_parse_phandle()
scsi: mpt3sas: Stop fw fault watchdog work item during system shutdown
Ralph Campbell [Mon, 25 Jul 2022 18:36:14 +0000 (11:36 -0700)]
mm/hmm: fault non-owner device private entries
If hmm_range_fault() is called with the HMM_PFN_REQ_FAULT flag and a
device private PTE is found, the hmm_range::dev_private_owner page is used
to determine if the device private page should not be faulted in.
However, if the device private page is not owned by the caller,
hmm_range_fault() returns an error instead of calling migrate_to_ram() to
fault in the page.
For example, if a page is migrated to GPU private memory and a RDMA fault
capable NIC tries to read the migrated page, without this patch it will
get an error. With this patch, the page will be migrated back to system
memory and the NIC will be able to read the data.
Jaewon Kim [Mon, 25 Jul 2022 09:52:12 +0000 (18:52 +0900)]
page_alloc: fix invalid watermark check on a negative value
There was a report that a task is waiting at the
throttle_direct_reclaim. The pgscan_direct_throttle in vmstat was
increasing.
This is a bug where zone_watermark_fast returns true even when the free
is very low. The commit b9f78fa27226 ("page_alloc: consider highatomic
reserve in watermark fast") changed the watermark fast to consider
highatomic reserve. But it did not handle a negative value case which
can be happened when reserved_highatomic pageblock is bigger than the
actual free.
If watermark is considered as ok for the negative value, allocating
contexts for order-0 will consume all free pages without direct reclaim,
and finally free page may become depleted except highatomic free.
Then allocating contexts may fall into throttle_direct_reclaim. This
symptom may easily happen in a system where wmark min is low and other
reclaimers like kswapd does not make free pages quickly.
Handle the negative case by using MIN.
Link: https://lkml.kernel.org/r/20220725095212.25388-1-jaewon31.kim@samsung.com Fixes: b9f78fa27226 ("page_alloc: consider highatomic reserve in watermark fast") Signed-off-by: Jaewon Kim <jaewon31.kim@samsung.com> Reported-by: GyeongHwan Hong <gh21.hong@samsung.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Minchan Kim <minchan@kernel.org> Cc: Baoquan He <bhe@redhat.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Yong-Taek Lee <ytk.lee@samsung.com> Cc: <stable@vger.kerenl.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Merge tag 'perf-tools-fixes-for-v5.19-2022-07-29' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix addresses for bss symbols, describing variables used in resolving
data access in tools such as 'perf c2c' and 'perf mem'.
- Skip symbols if SHF_ALLOC flag is not set, a technique used for
listing deprecated symbols, its addresses are zeros, so not useful.
- Remove undefined behavior from bpf_perf_object__next() when dealing
with an empty bpf_objects_list list.
- Make a ARM CoreSight disasm script work with both python2 and
python3.
- Sync x86's cpufeatures header with with the kernel sources.
* tag 'perf-tools-fixes-for-v5.19-2022-07-29' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf bpf: Remove undefined behavior from bpf_perf_object__next()
perf symbol: Skip symbols if SHF_ALLOC flag is not set
perf symbol: Correct address for bss symbols
perf scripts python: Let script to be python2 compliant
tools headers cpufeatures: Sync with the kernel sources
Merge tag 'pm-5.19-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Make some false positive RCU splats resulting from a recent intel_idle
driver change go away (Waiman Long)"
* tag 'pm-5.19-rc9' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: Fix false positive RCU splats due to incorrect hardirqs state
Lai Jiangshan [Fri, 29 Jul 2022 09:44:38 +0000 (17:44 +0800)]
workqueue: Avoid a false warning in unbind_workers()
Doing set_cpus_allowed_ptr() with wq_unbound_cpumask can be possible
fails and trigger the false warning.
Use cpu_possible_mask instead when wq_unbound_cpumask has no active CPUs.
It is very easy to trigger the warning:
Set wq_unbound_cpumask to a small set of CPUs.
Offline all the CPUs of wq_unbound_cpumask.
Offline an extra CPU and trigger the warning.
Fixes: 264fd0e7caf0 ("workqueue: Restrict kworker in the offline CPU pool running on housekeeping CPUs") Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com> Signed-off-by: Tejun Heo <tj@kernel.org>
Merge tag 'loongarch-fixes-5.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
- Fix cache size calculation, stack protection attributes, ptrace's
fpr_set and "ROM Size" in boardinfo
- Some cleanups and improvements of assembly
- Some cleanups of unused code and useless code
* tag 'loongarch-fixes-5.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: Fix wrong "ROM Size" of boardinfo
LoongArch: Fix missing fcsr in ptrace's fpr_set
LoongArch: Fix shared cache size calculation
LoongArch: Disable executable stack by default
LoongArch: Remove unused variables
LoongArch: Remove clock setting during cpu hotplug stage
LoongArch: Remove useless header compiler.h
LoongArch: Remove several syntactic sugar macros for branches
LoongArch: Re-tab the assembly files
LoongArch: Simplify "BGT foo, zero" with BGTZ
LoongArch: Simplify "BLT foo, zero" with BLTZ
LoongArch: Simplify "BEQ/BNE foo, zero" with BEQZ/BNEZ
LoongArch: Use the "move" pseudo-instruction where applicable
LoongArch: Use the "jr" pseudo-instruction where applicable
LoongArch: Use ABI names of registers where appropriate
PCI: Stub __pci_ioport_map() for arches that don't support it at all
When building OpenRISC PCI, which has no ioport_map(), we get the following
build error:
lib/pci_iomap.c: In function 'pci_iomap_range':
CC drivers/i2c/i2c-core-base.o
./include/asm-generic/pci_iomap.h:29:41: error: implicit declaration of function 'ioport_map'; did you mean 'ioremap'? [-Werror=implicit-function-declaration]
29 | #define __pci_ioport_map(dev, port, nr) ioport_map((port), (nr))
| ^~~~~~~~~~
lib/pci_iomap.c:44:24: note: in expansion of macro '__pci_ioport_map'
44 | return __pci_ioport_map(dev, start, len);
| ^~~~~~~~~~~~~~~~
Add a NULL definition of __pci_ioport_map() for architectures that do not
support ioport_map().
Merge tag 'powerpc-5.19-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable the new amdgpu display engine for powerpc, as long as the
compiler is correctly configured.
- Disable stack variable initialisation in prom_init to fix GCC 12
allmodconfig.
Thanks to Dan Horák and Sudip Mukherjee.
* tag 'powerpc-5.19-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
drm/amdgpu: Re-enable DCN for 64-bit powerpc
powerpc/64s: Disable stack variable initialisation for prom_init
Tiezhu Yang [Thu, 21 Jul 2022 09:53:01 +0000 (17:53 +0800)]
LoongArch: Fix wrong "ROM Size" of boardinfo
We can see the "ROM Size" is different in the following outputs:
[root@linux loongson]# cat /sys/firmware/loongson/boardinfo
BIOS Information
Vendor : Loongson
Version : vUDK2018-LoongArch-V2.0.pre-beta8
ROM Size : 63 KB
Release Date : 06/15/2022
Board Information
Manufacturer : Loongson
Board Name : Loongson-LS3A5000-7A1000-1w-A2101
Family : LOONGSON64
[root@linux loongson]# dmidecode | head -11
...
Handle 0x0000, DMI type 0, 26 bytes
BIOS Information
Vendor: Loongson
Version: vUDK2018-LoongArch-V2.0.pre-beta8
Release Date: 06/15/2022
ROM Size: 4 MB
According to "BIOS Information (Type 0) structure" in the SMBIOS
Reference Specification [1], it shows 64K * (n+1) is the size of
the physical device containing the BIOS if the size is less than
16M.
Additionally, we can see the related code in dmidecode [2]:
u64 s = { .l = (code1 + 1) << 6 };
So the output of dmidecode is correct, the output of boardinfo
is wrong, fix it.
By the way, at present no need to consider the size is 16M or
greater on LoongArch, because it is usually 4M or 8M which is
enough to use.
Current calculation of shared cache size is from the node (die) scope,
but we hope 'lscpu' to show the shared cache size of the whole package
for multi-die chips (e.g., Loongson-3C5000L, which contains 4 dies in
one package). So fix it by multiplying nodes_per_package.
Bibo Mao [Wed, 20 Jul 2022 07:21:51 +0000 (15:21 +0800)]
LoongArch: Remove clock setting during cpu hotplug stage
On physical machine we can save power by disabling clock of hot removed
cpu. However as different platforms require different methods to
configure clocks, the code is platform-specific, and probably belongs to
firmware/pmu or cpu regulator, rather than generic arch/loongarch code.
Also, there is no such register on QEMU virt machine since the
clock/frequency regulation is not emulated.
This patch removes the hard-coded clock register accesses in generic
LoongArch cpu hotplug flow.
Reviewed-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Bibo Mao <maobibo@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:22 +0000 (23:57 +0800)]
LoongArch: Re-tab the assembly files
Reflow the *.S files for better stylistic consistency, namely hard tabs
after mnemonic position, and vertical alignment of the first operand
with hard tabs. Tab width is obviously 8. Some pre-existing intra-block
vertical alignments are preserved.
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:21 +0000 (23:57 +0800)]
LoongArch: Simplify "BGT foo, zero" with BGTZ
Support for the syntactic sugar is present in upstream binutils port
from the beginning. Use it for shorter lines and better consistency.
Generated code should be identical.
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:20 +0000 (23:57 +0800)]
LoongArch: Simplify "BLT foo, zero" with BLTZ
Support for the syntactic sugar is present in upstream binutils port
from the beginning. Use it for shorter lines and better consistency.
Generated code should be identical.
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:19 +0000 (23:57 +0800)]
LoongArch: Simplify "BEQ/BNE foo, zero" with BEQZ/BNEZ
While B{EQ,NE}Z and B{EQ,NE} are different instructions, and the vastly
expanded range for branch destination does not really matter in the few
cases touched, use the B{EQ,NE}Z where possible for shorter lines and
better consistency (e.g. some places used "BEQ foo, zero", while some
used "BEQ zero, foo").
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:18 +0000 (23:57 +0800)]
LoongArch: Use the "move" pseudo-instruction where applicable
Some of the assembly code in the LoongArch port likely originated
from a time when the assembler did not support pseudo-instructions like
"move" or "jr", so the desugared form was used and readability suffers
(to a minor degree) as a result.
As the upstream toolchain supports these pseudo-instructions from the
beginning, migrate the existing few usages to them for better
readability.
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:17 +0000 (23:57 +0800)]
LoongArch: Use the "jr" pseudo-instruction where applicable
Some of the assembly code in the LoongArch port likely originated
from a time when the assembler did not support pseudo-instructions like
"move" or "jr", so the desugared form was used and readability suffers
(to a minor degree) as a result.
As the upstream toolchain supports these pseudo-instructions from the
beginning, migrate the existing few usages to them for better
readability.
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
WANG Xuerui [Tue, 26 Jul 2022 15:57:16 +0000 (23:57 +0800)]
LoongArch: Use ABI names of registers where appropriate
Some of the assembly in the LoongArch port seem to come from a
prehistoric time, when the assembler didn't even have support for the
ABI names we all come to know and love, thus used raw register numbers
which hampered readability.
The usages are found with a regex match inside arch/loongarch, then
manually adjusted for those non-definitions.
Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When offset is larger than the size of the bit array, we should not
attempt to access the array as we can perform an access beyond the
end of the array. Fix this by changing the pre-condition.
Using "cmp r2, r1; bhs ..." covers us for the size == 0 case, since
this will always take the branch when r1 is zero, irrespective of
the value of r2. This means we can fix this bug without adding any
additional code!
Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
x86/bugs: Do not enable IBPB at firmware entry when IBPB is not available
Some cloud hypervisors do not provide IBPB on very recent CPU processors,
including AMD processors affected by Retbleed.
Using IBPB before firmware calls on such systems would cause a GPF at boot
like the one below. Do not enable such calls when IBPB support is not
present.
Users may request that pages from an OpenCL SVM allocation be migrated
to the GPU with clEnqueueSVMMigrateMem(). In Nouveau this will call into
nouveau_dmem_migrate_vma() to do the migration. If the total range to be
migrated exceeds SG_MAX_SINGLE_ALLOC the pages will be migrated in
chunks of size SG_MAX_SINGLE_ALLOC. However a typo in updating the
starting address means that only the first chunk will get migrated.
Fix the calculation so that the entire range will get migrated if
possible.
Signed-off-by: Alistair Popple <apopple@nvidia.com> Fixes: f6e01c3642a3 ("drm/nouveau/svm: map pages after migration") Reviewed-by: Ralph Campbell <rcampbell@nvidia.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220720062745.960701-1-apopple@nvidia.com Cc: <stable@vger.kernel.org> # v5.8+
* tag 'net-5.19-final' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (67 commits)
stmmac: dwmac-mediatek: fix resource leak in probe
ipv6/addrconf: fix a null-ptr-deref bug for ip6_ptr
net: ping6: Fix memleak in ipv6_renew_options().
net/funeth: Fix fun_xdp_tx() and XDP packet reclaim
sctp: leave the err path free in sctp_stream_init to sctp_stream_free
sfc: disable softirqs for ptp TX
ptp: ocp: Select CRC16 in the Kconfig.
tcp: md5: fix IPv4-mapped support
virtio-net: fix the race between refill work and close
mptcp: Do not return EINPROGRESS when subflow creation succeeds
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
Bluetooth: Always set event mask on suspend
Bluetooth: mgmt: Fix double free on error path
wifi: mac80211: do not abuse fq.lock in ieee80211_do_stop()
ice: do not setup vlan for loopback VSI
ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
ice: Fix VSIs unable to share unicast MAC
ice: Fix tunnel checksum offload with fragmented traffic
ice: Fix max VLANs available for VF
netfilter: nft_queue: only allow supported familes and hooks
...
Ziyang Xuan [Thu, 28 Jul 2022 01:33:07 +0000 (09:33 +0800)]
ipv6/addrconf: fix a null-ptr-deref bug for ip6_ptr
Change net device's MTU to smaller than IPV6_MIN_MTU or unregister
device while matching route. That may trigger null-ptr-deref bug
for ip6_ptr probability as following.
=========================================================
BUG: KASAN: null-ptr-deref in find_match.part.0+0x70/0x134
Read of size 4 at addr 0000000000000308 by task ping6/263
Reproducer as following:
Firstly, prepare conditions:
$ip netns add ns1
$ip netns add ns2
$ip link add veth1 type veth peer name veth2
$ip link set veth1 netns ns1
$ip link set veth2 netns ns2
$ip netns exec ns1 ip -6 addr add 2001:0db8:0:f101::1/64 dev veth1
$ip netns exec ns2 ip -6 addr add 2001:0db8:0:f101::2/64 dev veth2
$ip netns exec ns1 ifconfig veth1 up
$ip netns exec ns2 ifconfig veth2 up
$ip netns exec ns1 ip -6 route add 2000::/64 dev veth1 metric 1
$ip netns exec ns2 ip -6 route add 2001::/64 dev veth2 metric 1
Secondly, execute the following two commands in two ssh windows
respectively:
$ip netns exec ns1 sh
$while true; do ip -6 addr add 2001:0db8:0:f101::1/64 dev veth1; ip -6 route add 2000::/64 dev veth1 metric 1; ping6 2000::2; done
$ip netns exec ns1 sh
$while true; do ip link set veth1 mtu 1000; ip link set veth1 mtu 1500; sleep 5; done
It is because ip6_ptr has been assigned to NULL in addrconf_ifdown() firstly,
then ip6_ignore_linkdown() accesses ip6_ptr directly without NULL check.
When we close ping6 sockets, some resources are left unfreed because
pingv6_prot is missing sk->sk_prot->destroy(). As reported by
syzbot [0], just three syscalls leak 96 bytes and easily cause OOM.
struct ipv6_sr_hdr *hdr;
char data[24] = {0};
int fd;
To fix memory leaks, let's add a destroy function.
Note the socket() syscall checks if the GID is within the range of
net.ipv4.ping_group_range. The default value is [1, 0] so that no
GID meets the condition (1 <= GID <= 0). Thus, the local DoS does
not succeed until we change the default value. However, at least
Ubuntu/Fedora/RHEL loosen it.
watch_queue: Fix missing locking in add_watch_to_object()
If a watch is being added to a queue, it needs to guard against
interference from addition of a new watch, manual removal of a watch and
removal of a watch due to some other queue being destroyed.
KEYCTL_WATCH_KEY guards against this for the same {key,queue} pair by
holding the key->sem writelocked and by holding refs on both the key and
the queue - but that doesn't prevent interaction from other {key,queue}
pairs.
While add_watch_to_object() does take the spinlock on the event queue,
it doesn't take the lock on the source's watch list. The assumption was
that the caller would prevent that (say by taking key->sem) - but that
doesn't prevent interference from the destruction of another queue.
Fix this by locking the watcher list in add_watch_to_object().
Fixes: 175295c8c9fa ("pipe: Add general notification queue support") Reported-by: syzbot+03d7b43290037d1f87ca@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com>
cc: keyrings@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 28 Jul 2022 09:31:06 +0000 (10:31 +0100)]
watch_queue: Fix missing rcu annotation
Since __post_watch_notification() walks wlist->watchers with only the
RCU read lock held, we need to use RCU methods to add to the list (we
already use RCU methods to remove from the list).
Fix add_watch_to_object() to use hlist_add_head_rcu() instead of
hlist_add_head() for that list.
Fixes: 175295c8c9fa ("pipe: Add general notification queue support") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/funeth: Fix fun_xdp_tx() and XDP packet reclaim
The current implementation of fun_xdp_tx(), used for XPD_TX, is
incorrect in that it takes an address/length pair and later releases it
with page_frag_free(). It is OK for XDP_TX but the same code is used by
ndo_xdp_xmit. In that case it loses the XDP memory type and releases the
packet incorrectly for some of the types. Assorted breakage follows.
Change fun_xdp_tx() to take xdp_frame and rely on xdp_return_frame() in
reclaim.
Jakub Kicinski [Thu, 28 Jul 2022 02:56:28 +0000 (19:56 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-07-26
This series contains updates to ice driver only.
Przemyslaw corrects accounting for VF VLANs to allow for correct number
of VLANs for untrusted VF. He also correct issue with checksum offload
on VXLAN tunnels.
Ani allows for two VSIs to share the same MAC address.
Maciej corrects checked bits for descriptor completion of loopback
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: do not setup vlan for loopback VSI
ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
ice: Fix VSIs unable to share unicast MAC
ice: Fix tunnel checksum offload with fragmented traffic
ice: Fix max VLANs available for VF
====================
This happens when calling sctp_sendmsg without connecting to server first.
In this case, a data chunk already queues up in send queue of client side
when processing the INIT_ACK from server in sctp_process_init() where it
calls sctp_stream_init() to alloc stream_in. If it fails to alloc stream_in
all stream_out will be freed in sctp_stream_init's err path. Then in the
asoc freeing it will crash when dequeuing this data chunk as stream_out
is missing.
As we can't free stream out before dequeuing all data from send queue, and
this patch is to fix it by moving the err path stream_out/in freeing in
sctp_stream_init() to sctp_stream_free() which is eventually called when
freeing the asoc in sctp_association_free(). This fix also makes the code
in sctp_process_init() more clear.
Note that in sctp_association_init() when it fails in sctp_stream_init(),
sctp_association_free() will not be called, and in that case it should
go to 'stream_free' err path to free stream instead of 'fail_init'.
Sending a PTP packet can imply to use the normal TX driver datapath but
invoked from the driver's ptp worker. The kernel generic TX code
disables softirqs and preemption before calling specific driver TX code,
but the ptp worker does not. Although current ptp driver functionality
does not require it, there are several reasons for doing so:
1) The invoked code is always executed with softirqs disabled for non
PTP packets.
2) Better if a ptp packet transmission is not interrupted by softirq
handling which could lead to high latencies.
3) netdev_xmit_more used by the TX code requires preemption to be
disabled.
Indeed a solution for dealing with kernel preemption state based on static
kernel configuration is not possible since the introduction of dynamic
preemption level configuration at boot time using the static calls
functionality.
Eric Dumazet [Tue, 26 Jul 2022 11:57:43 +0000 (11:57 +0000)]
tcp: md5: fix IPv4-mapped support
After the blamed commit, IPv4 SYN packets handled
by a dual stack IPv6 socket are dropped, even if
perfectly valid.
$ nstat | grep MD5
TcpExtTCPMD5Failure 5 0.0
For a dual stack listener, an incoming IPv4 SYN packet
would call tcp_inbound_md5_hash() with @family == AF_INET,
while tp->af_specific is pointing to tcp_sock_ipv6_specific.
Only later when an IPv4-mapped child is created, tp->af_specific
is changed to tcp_sock_ipv6_mapped_specific.
Fixes: fa64e214abdb ("net/tcp: Merge TCP-MD5 inbound callbacks") Reported-by: Brian Vazquez <brianvv@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Dmitry Safonov <dima@arista.com> Tested-by: Leonard Crestez <cdleonard@gmail.com> Link: https://lore.kernel.org/r/20220726115743.2759832-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit be1c3685b6f1 ("mm/memblock: add memblock memory allocation apis")
added a check to determine whether arm_dma_zone_size is exceeding the
amount of kernel virtual address space available between the upper 4GB
virtual address limit and PAGE_OFFSET in order to provide a suitable
definition of MAX_DMA_ADDRESS that should fit within the 32-bit virtual
address space. The quantity used for comparison was off by a missing
trailing 0, leading to MAX_DMA_ADDRESS to be overflowing a 32-bit
quantity.
This was caught thanks to CONFIG_DEBUG_VIRTUAL on the bcm2711 platform
where we define a dma_zone_size of 1GB and we have a PAGE_OFFSET value
of 0xc000_0000 (CONFIG_VMSPLIT_3G) leading to MAX_DMA_ADDRESS being
0x1_0000_0000 which overflows the unsigned long type used throughout
__pa() and then __virt_addr_valid(). Because the virtual address passed
to __virt_addr_valid() would now be 0, the function would loudly warn
and flood the kernel log, thus making the platform unable to boot
properly.
Merge tag 'asm-generic-fixes-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"Two more bug fixes for asm-generic, one addressing an incorrect
Kconfig symbol reference and another one fixing a build failure for
the perf tool on mips and possibly others"
* tag 'asm-generic-fixes-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove a broken and needless ifdef conditional
tools: Fixed MIPS builds due to struct flock re-definition
Ian Rogers [Tue, 26 Jul 2022 22:09:21 +0000 (15:09 -0700)]
perf bpf: Remove undefined behavior from bpf_perf_object__next()
bpf_perf_object__next() folded the last element in the list test with the
empty list test. However, this meant that offsets were computed against
null and that a struct list_head was compared against a 'struct
bpf_perf_object'.
Working around this with clang's undefined behavior sanitizer required
-fno-sanitize=null and -fno-sanitize=object-size.
Remove the undefined behavior by using the regular Linux list APIs and
handling the starting case separately from the end testing case.
Looking at uses like bpf_perf_object__for_each(), as the constant NULL
or non-NULL argument can be constant propagated, the code is no less
efficient.
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrii Nakryiko <andrii@kernel.org> Cc: Christy Lee <christylee@fb.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Miaoqian Lin <linmq006@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Tom Rix <trix@redhat.com> Cc: bpf@vger.kernel.org Cc: llvm@lists.linux.dev Link: https://lore.kernel.org/r/20220726220921.2567761-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Sun, 24 Jul 2022 06:00:13 +0000 (14:00 +0800)]
perf symbol: Skip symbols if SHF_ALLOC flag is not set
Some symbols are observed with the 'st_value' field zeroed. E.g.
libc.so.6 in Ubuntu contains a symbol '__evoke_link_warning_getwd' which
resides in the '.gnu.warning.getwd' section.
Unlike normal sections, such kind of sections are used for linker
warning when a file calls deprecated functions, but they are not part of
memory images, the symbols in these sections should be dropped.
This patch checks the section attribute SHF_ALLOC bit, if the bit is not
set, it skips symbols to avoid spurious ones.
Suggested-by: Fangrui Song <maskray@google.com> Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Chang Rui <changruinj@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220724060013.171050-3-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Leo Yan [Sun, 24 Jul 2022 06:00:12 +0000 (14:00 +0800)]
perf symbol: Correct address for bss symbols
When using 'perf mem' and 'perf c2c', an issue is observed that tool
reports the wrong offset for global data symbols. This is a common
issue on both x86 and Arm64 platforms.
Let's see an example, for a test program, below is the disassembly for
its .bss section which is dumped with objdump:
First we used 'perf mem record' to run the test program and then used
'perf --debug verbose=4 mem report' to observe what's the symbol info
for 'buf1' and 'buf2' structures.
The perf tool relies on libelf to parse symbols, in executable and
shared object files, 'st_value' holds a virtual address; 'sh_addr' is
the address at which section's first byte should reside in memory, and
'sh_offset' is the byte offset from the beginning of the file to the
first byte in the section. The perf tool uses below formula to convert
a symbol's memory address to a file address:
We can see the final adjusted address ranges for buf1 and buf2 are
[0x30a8-0x30e8) and [0x3068-0x30a8) respectively, apparently this is
incorrect, in the code, the structure for 'buf1' and 'buf2' specifies
compiler attribute with 64-byte alignment.
The problem happens for 'sh_offset', libelf returns it as 0x3028 which
is not 64-byte aligned, combining with disassembly, it's likely libelf
doesn't respect the alignment for .bss section, therefore, it doesn't
return the aligned value for 'sh_offset'.
Suggested by Fangrui Song, ELF file contains program header which
contains PT_LOAD segments, the fields p_vaddr and p_offset in PT_LOAD
segments contain the execution info. A better choice for converting
memory address to file address is using the formula:
file_address = st_value - p_vaddr + p_offset
This patch introduces elf_read_program_header() which returns the
program header based on the passed 'st_value', then it uses the formula
above to calculate the symbol file address; and the debugging log is
updated respectively.
Leo Yan [Mon, 25 Jul 2022 10:42:20 +0000 (18:42 +0800)]
perf scripts python: Let script to be python2 compliant
The mainline kernel can be used for relative old distros, e.g. RHEL 7.
The distro doesn't upgrade from python2 to python3, this causes the
building error that the python script is not python2 compliant.
To fix the building failure, this patch changes from the python f-string
format to traditional string format.
Fixes: efa17435286d97b7 ("perf scripts python: Support Arm CoreSight trace data disassembly") Reported-by: Akemi Yagi <toracat@elrepo.org> Signed-off-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: ElRepo <contact@elrepo.org> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220725104220.1106663-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
CC /tmp/build/perf/bench/mem-memset-x86-64-asm.o
And addresses this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org Link: https://lore.kernel.org/lkml/Yt6oWce9UDAmBAtX@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jason Wang [Mon, 25 Jul 2022 07:21:59 +0000 (15:21 +0800)]
virtio-net: fix the race between refill work and close
We try using cancel_delayed_work_sync() to prevent the work from
enabling NAPI. This is insufficient since we don't disable the source
of the refill work scheduling. This means an NAPI poll callback after
cancel_delayed_work_sync() can schedule the refill work then can
re-enable the NAPI that leads to use-after-free [1].
Since the work can enable NAPI, we can't simply disable NAPI before
calling cancel_delayed_work_sync(). So fix this by introducing a
dedicated boolean to control whether or not the work could be
scheduled from NAPI.
[1]
==================================================================
BUG: KASAN: use-after-free in refill_work+0x43/0xd4
Read of size 2 at addr ffff88810562c92e by task kworker/2:1/42
Fixes: 5a39848b6859f ("virtio_net: set/cancel work on ndo_open/ndo_stop") Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Handle 0x0020, DMI type 17, 84 bytes
Memory Device
Array Handle: 0x0013
Error Information Handle: Not Provided
Total Width: 72 bits
Data Width: 64 bits
Size: 32 GB
Form Factor: DIMM
Set: None
Locator: PROC 1 DIMM 1 <===== device
Bank Locator: Not Specified <===== bank
This results in a buffer overflow because ghes_edac_register() calls
strlen() on an uninitialized label, which had non-zero values left over
from krealloc_array():
The label contains garbage because the commit in Fixes reallocs the
DIMMs array while scanning the system but doesn't clear the newly
allocated memory.
Change dimm_setup_label() to always initialize the label to fix the
issue. Set it to the empty string in case BIOS does not provide both
bank and device so that ghes_edac_register() can keep the default label
given by edac_mc_alloc_dimms().
[ bp: Rewrite commit message. ]
Fixes: 66721d153402a ("EDAC/ghes: Scan the system once on driver init") Co-developed-by: Robert Richter <rric@kernel.org> Signed-off-by: Robert Richter <rric@kernel.org> Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Robert Elliott <elliott@hpe.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220719220124.760359-1-toshi.kani@hpe.com
Mat Martineau [Mon, 25 Jul 2022 20:52:31 +0000 (13:52 -0700)]
mptcp: Do not return EINPROGRESS when subflow creation succeeds
New subflows are created within the kernel using O_NONBLOCK, so
EINPROGRESS is the expected return value from kernel_connect().
__mptcp_subflow_connect() has the correct logic to consider EINPROGRESS
to be a successful case, but it has also used that error code as its
return value.
Before v5.19 this was benign: all the callers ignored the return
value. Starting in v5.19 there is a MPTCP_PM_CMD_SUBFLOW_CREATE generic
netlink command that does use the return value, so the EINPROGRESS gets
propagated to userspace.
Make __mptcp_subflow_connect() always return 0 on success instead.
Fixes: 8e381f2c7ea7 ("mptcp: Add handling of outgoing MP_JOIN requests") Fixes: 33ecd4cecca3 ("mptcp: netlink: allow userspace-driven subflow establishment") Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Link: https://lore.kernel.org/r/20220725205231.87529-1-mathew.j.martineau@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1) If nf_queue user requests packet truncation below size of l3 header,
we corrupt the skb, then crash. Reject such requests.
2) add cond_resched() calls when doing cycle detection in the
nf_tables graph. This avoids softlockup warning with certain
rulesets.
3) Reject rulesets that use nftables 'queue' expression in family/chain
combinations other than those that are supported. Currently the ruleset
will load, but when userspace attempts to reinject you get WARN splat +
packet drops.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_queue: only allow supported familes and hooks
netfilter: nf_tables: add rescheduling points during loop detection walks
netfilter: nf_queue: do not allow packet truncation below transport header offset
====================
Jakub Kicinski [Wed, 27 Jul 2022 02:48:24 +0000 (19:48 -0700)]
Merge tag 'for-net-2022-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix early wakeup after suspend
- Fix double free on error
- Fix use-after-free on l2cap_chan_put
* tag 'for-net-2022-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
Bluetooth: Always set event mask on suspend
Bluetooth: mgmt: Fix double free on error path
====================
Merge tag 'mm-hotfixes-stable-2022-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Thirteen hotfixes.
Eight are cc:stable and the remainder are for post-5.18 issues or are
too minor to warrant backporting"
* tag 'mm-hotfixes-stable-2022-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mailmap: update Gao Xiang's email addresses
userfaultfd: provide properly masked address for huge-pages
Revert "ocfs2: mount shared volume without ha stack"
hugetlb: fix memoryleak in hugetlb_mcopy_atomic_pte
fs: sendfile handles O_NONBLOCK of out_fd
ntfs: fix use-after-free in ntfs_ucsncmp()
secretmem: fix unhandled fault in truncate
mm/hugetlb: separate path for hwpoison entry in copy_hugetlb_page_range()
mm: fix missing wake-up event for FSDAX pages
mm: fix page leak with multiple threads mapping the same page
mailmap: update Seth Forshee's email address
tmpfs: fix the issue that the mount and remount results are inconsistent.
mm: kfence: apply kmemleak_ignore_phys on early allocated pool
scsi: ufs: core: Fix a race condition related to device management
If a device management command completion happens after
wait_for_completion_timeout() times out and before ufshcd_clear_cmds() is
called, then the completion code may crash on the complete() call in
__ufshcd_transfer_req_compl().
Link: https://lore.kernel.org/r/20220720170228.1598842-1-bvanassche@acm.org Fixes: e1bdc4828f1a ("[SCSI] ufs: Add support for sending NOP OUT UPIU") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Avri Altman <avri.altman@wdc.com> Cc: Bean Huo <beanhuo@micron.com> Cc: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jason Yan [Wed, 20 Jul 2022 02:51:20 +0000 (10:51 +0800)]
scsi: core: Fix warning in scsi_alloc_sgtables()
As explained in SG_IO howto[1]:
"If iovec_count is non-zero then 'dxfer_len' should be equal to the sum of
iov_len lengths. If not, the minimum of the two is the transfer length."
When iovec_count is non-zero and dxfer_len is zero, the sg_io() just
genarated a null bio, and finally caused a warning below. To fix it, skip
generating a bio for this request if dxfer_len is zero.
Link: https://lore.kernel.org/r/20220720025120.3226770-1-yanaijie@huawei.com Fixes: 09a5fc218fb8 ("block: fix SG_IO vector request data length handling") Reported-by: syzbot+d44b35ecfb807e5af0b5@syzkaller.appspotmail.com Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
David Jeffery [Fri, 22 Jul 2022 14:24:48 +0000 (10:24 -0400)]
scsi: mpt3sas: Stop fw fault watchdog work item during system shutdown
During system shutdown or reboot, mpt3sas will reset the firmware back to
ready state. However, the driver leaves running a watchdog work item
intended to keep the firmware in operational state. This causes a second,
unneeded reset on shutdown and moves the firmware back to operational
instead of in ready state as intended. And if the mpt3sas_fwfault_debug
module parameter is set, this extra reset also panics the system.
mpt3sas's scsih_shutdown needs to stop the watchdog before resetting the
firmware back to ready state.
Link: https://lore.kernel.org/r/20220722142448.6289-1-djeffery@redhat.com Fixes: 80df4e6869c9 ("scsi: mpt3sas: Transition IOC to Ready state during shutdown") Tested-by: Laurence Oberman <loberman@redhat.com> Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: David Jeffery <djeffery@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I've been in Alibaba Cloud for more than one year, mainly to address
cloud-native challenges (such as high-performance container images) for
open source communities.
Update my email addresses on behalf of my current employer (Alibaba Cloud)
to support all my (team) work in this area. Also add an outdated
@redhat.com address of me.
Nadav Amit [Mon, 11 Jul 2022 16:59:06 +0000 (09:59 -0700)]
userfaultfd: provide properly masked address for huge-pages
Commit 976564d0daca ("userfaultfd: provide unmasked address on
page-fault") was introduced to fix an old bug, in which the offset in the
address of a page-fault was masked. Concerns were raised - although were
never backed by actual code - that some userspace code might break because
the bug has been around for quite a while. To address these concerns a
new flag was introduced, and only when this flag is set by the user,
userfaultfd provides the exact address of the page-fault.
The commit however had a bug, and if the flag is unset, the offset was
always masked based on a base-page granularity. Yet, for huge-pages, the
behavior prior to the commit was that the address is masked to the
huge-page granulrity.
While there are no reports on real breakage, fix this issue. If the flag
is unset, use the address with the masking that was done before.
Link: https://lkml.kernel.org/r/20220711165906.2682-1-namit@vmware.com Fixes: 976564d0daca ("userfaultfd: provide unmasked address on page-fault") Signed-off-by: Nadav Amit <namit@vmware.com> Reported-by: James Houghton <jthoughton@google.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Peter Xu <peterx@redhat.com> Reviewed-by: James Houghton <jthoughton@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Jan Kara <jack@suse.cz> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put
This fixes the following trace which is caused by hci_rx_work starting up
*after* the final channel reference has been put() during sock_close() but
*before* the references to the channel have been destroyed, so instead
the code now rely on kref_get_unless_zero/l2cap_chan_hold_unless_zero to
prevent referencing a channel that is about to be destroyed.
refcount_t: increment on 0; use-after-free.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x20/0xd0
Read of size 4 at addr ffffffc114f5bf18 by task kworker/u17:14/705
CPU: 4 PID: 705 Comm: kworker/u17:14 Tainted: G S W 4.14.234-00003-g1fb6d0bd49a4-dirty #28
Hardware name: Qualcomm Technologies, Inc. SM8150 V2 PM8150
Google Inc. MSM sm8150 Flame DVT (DT)
Workqueue: hci0 hci_rx_work
Call trace:
dump_backtrace+0x0/0x378
show_stack+0x20/0x2c
dump_stack+0x124/0x148
print_address_description+0x80/0x2e8
__kasan_report+0x168/0x188
kasan_report+0x10/0x18
__asan_load4+0x84/0x8c
refcount_dec_and_test+0x20/0xd0
l2cap_chan_put+0x48/0x12c
l2cap_recv_frame+0x4770/0x6550
l2cap_recv_acldata+0x44c/0x7a4
hci_acldata_packet+0x100/0x188
hci_rx_work+0x178/0x23c
process_one_work+0x35c/0x95c
worker_thread+0x4cc/0x960
kthread+0x1a8/0x1c4
ret_from_fork+0x10/0x18
Cc: stable@kernel.org Reported-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When suspending, always set the event mask once disconnects are
successful. Otherwise, if wakeup is disallowed, the event mask is not
set before suspend continues and can result in an early wakeup.
Fixes: b7ac669c9a6b ("Bluetooth: hci_sync: Rework hci_suspend_notifier") Cc: stable@vger.kernel.org Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
wifi: mac80211: do not abuse fq.lock in ieee80211_do_stop()
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit d6ce4edfa869a6a6 ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Currently loopback test is failiing due to the error returned from
ice_vsi_vlan_setup(). Skip calling it when preparing loopback VSI.
Fixes: 9616d5b28366 ("ice: Add handler for ethtool selftest") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice: check (DD | EOF) bits on Rx descriptor rather than (EOP | RS)
Tx side sets EOP and RS bits on descriptors to indicate that a
particular descriptor is the last one and needs to generate an irq when
it was sent. These bits should not be checked on completion path
regardless whether it's the Tx or the Rx. DD bit serves this purpose and
it indicates that a particular descriptor is either for Rx or was
successfully Txed. EOF is also set as loopback test does not xmit
fragmented frames.
Look at (DD | EOF) bits setting in ice_lbtest_receive_frames() instead
of EOP and RS pair.
Fixes: 9616d5b28366 ("ice: Add handler for ethtool selftest") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently does not allow two VSIs in the same PF domain
to have the same unicast MAC address. This is incorrect in the sense
that a policy decision is being made in the driver when it must be
left to the user. This approach was causing issues when rebooting
the system with VFs spawned not being able to change their MAC addresses.
Such errors were present in dmesg:
[ 7921.068237] ice 0000:b6:00.2 ens2f2: Unicast MAC 6a:0d:e4:70:ca:d1 already
exists on this PF. Preventing setting VF 7 unicast MAC address to 6a:0d:e4:70:ca:d1
Fix that by removing this restriction. Doing this also allows
us to remove some additional code that's checking if a unicast MAC
filter already exists.
Fixes: 2f12d696cbab ("ice: Check if unicast MAC exists before setting VF MAC") Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice: Fix tunnel checksum offload with fragmented traffic
Fix checksum offload on VXLAN tunnels.
In case, when mpls protocol is not used, set l4 header to transport
header of skb. This fixes case, when user tries to offload checksums
of VXLAN tunneled traffic.
Steps for reproduction (requires link partner with tunnels):
ip l s enp130s0f0 up
ip a f enp130s0f0
ip a a 10.10.110.2/24 dev enp130s0f0
ip l s enp130s0f0 mtu 1600
ip link add vxlan12_sut type vxlan id 12 group 238.168.100.100 dev enp130s0f0 dstport 4789
ip l s vxlan12_sut up
ip a a 20.10.110.2/24 dev vxlan12_sut
iperf3 -c 20.10.110.1 #should connect
Offload params: td_offset, cd_tunnel_params were
corrupted, due to l4 header pointing wrong address. NIC would then drop
those packets internally, due to incorrect TX descriptor data,
which increased GLV_TEPC register.
Fixes: 3bd8ff3a0608 ("ice: Add mpls+tso support") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Legacy VLAN implementation allows for untrusted VF to have 8 VLAN
filters, not counting VLAN 0 filters. Current VLAN_V2 implementation
lowers available filters for VF, by counting in VLAN 0 filter for both
TPIDs.
Fix this by counting only non zero VLAN filters.
Without this patch, untrusted VF would not be able to access 8 VLAN
filters.
Fixes: d81279357b19 ("ice: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
projects / kernel.git / log