Daniel Vetter [Fri, 29 Jun 2012 20:40:09 +0000 (22:40 +0200)]
drm/i915: add direct encoder disable/enable infrastructure
Just prep work, not yet put to some use.
Note that because we're still using the crtc helper to switch modes
(and their complicated way to do partial modesets), we need to call
the encoder's disable function unconditionally.
But once this is cleaned up we shouldn't call the encoder's disable
function unconditionally any more, because then we know that we'll
only call it if the encoder is actually enabled. Also note that we
then need to be careful about which crtc we're filtering the encoder
list on: We want to filter on the crtc of the _current_ mode, not the
one we're about to set up.
For the enabling side we need to do the same trick. And again, we
should be able to simplify this quite a bit when things have settled
into place.
Also note that this simply does not take cloning into account, so dpms
needs to be handled specially for the few outputs where we even bother
with it.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 29 Jun 2012 20:53:09 +0000 (22:53 +0200)]
drm/i915: rip out crtc prepare/commit indirection
Just impendance matching with the the crtc helper stuff.
... and somehow the design of this all ended up in this commit here,
too ;-)
The big plan is that this new set of crtc display_funcs take full
responsibility of modeset operations for the entire display output
pipeline (by calling down into object-specific callbacks and
functions). The platform-specific callbacks simply know best what the
proper order is.
This has the drawback that we can't do minimal change-overs any more
if a modeset just disables one encoder in a cloned configuration
(because we will only expose a disable/enable action that takes
down/sets up the entire crtc including all encoders). Imo that's the
only sane way to do it though:
- The use-case for this is pretty minimal, even when presenting (at
least sane people) should use a dual-screen output so that you can
see your notes on your panel. Clone mode is imo BS.
- With all the clone mode constrains, shared resources, and special
ordering requirements (which differ even on the same platform
sometimes for different outputs) there's no way we'd get this right
for all cases. Especially since this is a under-used feature.
- And to top it off: On haswell even dp link re-training requires us
to take down the entire display pipe - otherwise the chip dies.
So the only sane way is to do a full modeset on every crtc where the
output config changes in any way.
To support global modeset (i.e. set the configuration for all crtcs at
once) we'd then add one more function to allocate global and shared
objects in the best ways (e.g. fdi links, pch plls, ...). The crtc
functions would then simply use the pre-allocated stuff (and shouldn't
be able to fail, ever). We could even do all the object pinning in
there (and maybe try to defragment the global gtt if we fail)!
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 29 Jun 2012 20:39:33 +0000 (22:39 +0200)]
drm/i915: add crtc->enable/disable vfuncs insted of dpms
Because that's what we're essentially calling. This is the first step
in untangling the crtc_helper induced dpms handling mess we have - at
the crtc level we only have 2 states and the magic is just in
selecting which one (and atm there isn't even much magic, but on
recent platforms where not even the crt output has more than 2 states
we could do better).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 16 Aug 2012 14:43:37 +0000 (22:43 +0800)]
drm/i915: Haswell HDMI audio initialization
Added new haswell_write_eld() to initialize Haswell HDMI audio registers
to generate an unsolicited response to the audio controller driver to
indicate that the controller sequence should start.
Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Wang Xingchao <xingchao.wang@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Thu, 16 Aug 2012 00:15:34 +0000 (10:15 +1000)]
drm/i915: implement dma buf begin_cpu_access (v2)
In order for udl vmap to work properly, we need to push the object
into the CPU domain before we start copying the data to the USB device.
This along with the udl change avoids userspace explicit mapping to
be used.
v2: add a flag for userspace to query to know if Intel kernel driver can
deal with the vmap flushing properly. In theory udl would need a flag also,
but I intend to push the patches very close to each other and other drivers
should do the right thing from the start.
I've added a test to my intel-gpu-tools prime branch, however testing
this is a bit messy since the only way to get udl to vmap is to rendering
something. I've tested this with real code as well to make sure it works.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[danvet: resolved conflict, which required reallocating the PARAM
number to 21.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 15 Aug 2012 18:23:25 +0000 (19:23 +0100)]
drm/i915: Don't hardcode the number of pipes in the error state dump
New-ish devices have 3 pipes, so let's not just hardcode 2 but use the
for_each_pipe() macro and make struct intel_display_error_state is big
enough.
V2: Also add the number of pipes emitted (Chris Wilson)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 12 Aug 2012 16:15:48 +0000 (18:15 +0200)]
drm/fb-helper: don't clobber output routing in setup_crtcs
Yet again the too close relationship between the fb helper and the
crtc helper code strikes. This time around the fb helper resets all
encoder->crtc pointers to NULL before starting to set up it's own
mode. Which is total bullocks, because this will clobber the existing
output routing, which the new drm/i915 code depends upon to be
absolutely correct.
The crtc helper itself doesn't really care about that, since it
disables unused encoders in a rather roundabout way anyway.
Two places call drm_setup_crts:
- For the initial fb config. I've auditted all current drivers, and
they all allocate their encoders with kzalloc. So there's no need to
clear encoder->crtc once more.
- When processing hotplug events while showing the fb console. This
one is a bit more tricky, but both the crtc helper code and the new
drm/i915 modeset code disable encoders if their crtc is changed and
that encoder isn't part of the new config. Also, both disable any
disconnected outputs, too.
Which only leaves encoders that are on, connected, but for some odd
reason the fb helper code doesn't want to use. That would be a bug
in the fb configuration selector, since it tries to light up as many
outputs as possible.
v2: Kill the now unused encoders variable.
Acked-by: Dave Airlie <airlied@gmail.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 9 Aug 2012 08:52:18 +0000 (16:52 +0800)]
drm/i915: ironlake_write_eld code cleanup
Use _PIPE macro to get correct register definition for IBX/CPT, discard
old variable "i" way.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Added the DIP_PORT_SEL #define from a preceeding patch in the
series that needs more work.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 9 Aug 2012 08:52:16 +0000 (16:52 +0800)]
drm/i915: write eld info for HDMI audio
HDMI audio related registers will be configured in write_eld callback.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wang Xingchao [Thu, 9 Aug 2012 08:52:15 +0000 (16:52 +0800)]
drm/i915: HSW audio registers definition
Add hsw audio registers definition
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 12 Aug 2012 17:27:12 +0000 (19:27 +0200)]
drm/i915: simplify dvo dpms interface
All dvo drivers only support 2 dpms states, and our dvo driver
even switches of the dvo port for anything else than DPMS_ON. Hence
ditch this complexity and simply use bool enable.
While reading through this code I've noticed that the mode_set
function of ch7017 is a bit peculiar - it disable the lvds again, even
though the crtc helper code should have done that ... This might be to
work around an issue at driver load, we pretty much ignore the hw
state when taking over.
v2: Also do the conversion for the new ns2501 driver.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 12 Aug 2012 17:27:11 +0000 (19:27 +0200)]
drm/i915: prepare load-detect pipe code for dpms changes
A few things need adjustement:
- Change the dpms state by calling the dpms connector function and
not some crtc helper internal callbacks. Otherwise this will break
once we switch to our own dpms handling.
- Instead of tracking and restoring intel_crtc->dpms_mode use the
connector's dpms variable - the former relies on the dpms compuation
rules used by the crtc helper. And it would break when the encoder
is cloned and the other output has a different dpms state. But luckily
no one is crazy enough for that.
- Properly clear the connector -> encoder -> crtc linking, even when
failing (note that the crtc helper removes the encoder -> crtc link
in disabled_unused_functions for us).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 12 Aug 2012 17:27:10 +0000 (19:27 +0200)]
drm/i915: rip out the overlay pipe A workaround
Now that all affected i830M systems have the pipe A quirk set,
we don't need to do any special dances in the overlay code any
longer. And reading through the code I'm rather dubios that it
actually does what it claims to do ...
As a nice benefit this rips out a users of the crtc helper dpms
callback.
v2: As suggested by Chris Wilson, replace the code by an appropriate
WARN to ensure that the pipe A is indeed running.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Anhua Xu <anhua.xu@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Fri, 17 Aug 2012 06:57:56 +0000 (08:57 +0200)]
Merge tag 'v3.6-rc2' into drm-intel-next
Backmerge Linux 3.6-rc2 to resolve a few funny conflicts before we put
even more madness on top:
- drivers/gpu/drm/i915/i915_irq.c: Just a spurious WARN removed in
-fixes, that has been changed in a variable-rename in -next, too.
- drivers/gpu/drm/i915/intel_ringbuffer.c: -next remove scratch_addr
(since all their users have been extracted in another fucntion),
-fixes added another user for a hw workaroudn.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ian Kent [Mon, 6 Aug 2012 01:37:47 +0000 (09:37 +0800)]
autofs4 - fix get_next_positive_subdir()
Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.
The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 16 Aug 2012 18:47:42 +0000 (11:47 -0700)]
Merge tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Just a trivial patch to include vfio.h in the installed headers so we
can complete userspace integration into QEMU."
* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Include vfio.h in installed headers
Linus Torvalds [Thu, 16 Aug 2012 18:31:59 +0000 (11:31 -0700)]
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
Linus Torvalds [Thu, 16 Aug 2012 18:13:16 +0000 (11:13 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Linus Torvalds [Thu, 16 Aug 2012 18:08:32 +0000 (11:08 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
Dave Airlie [Wed, 15 Aug 2012 10:31:22 +0000 (20:31 +1000)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Dave Airlie [Wed, 15 Aug 2012 10:27:51 +0000 (20:27 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
David S. Miller [Wed, 15 Aug 2012 07:37:29 +0000 (00:37 -0700)]
sparc64: Be less verbose during vmemmap population.
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit ccd3a32a52f9902d9687a8afb20161a9e7e20479
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322 Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671 Tested-by: Roberto Romer <sildurin@gmail.com> Tested-by: Daniel Wagner <wagi@monom.org> Tested-by: Keith Packard <keithp@keithp.com> Cc: stable@vger.kernel.org Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Tue, 14 Aug 2012 04:58:59 +0000 (07:58 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Linus Torvalds [Tue, 14 Aug 2012 04:52:41 +0000 (07:52 +0300)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
Arnd Bergmann [Mon, 13 Aug 2012 14:36:10 +0000 (14:36 +0000)]
GPIO: gpio-pxa: fix building without CONFIG_OF
Commit 44e9efc670 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Ben Skeggs [Fri, 27 Jul 2012 04:18:03 +0000 (14:18 +1000)]
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
Dave Airlie [Mon, 13 Aug 2012 23:25:01 +0000 (09:25 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex Deucher writes:
This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA
I've tested on a number of cards across generations and noticed no problems.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
Jani Nikula [Mon, 13 Aug 2012 14:33:02 +0000 (17:33 +0300)]
drm/i915: ensure i2c adapter is all set before adding it
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de> Tested-by: Mihai Moldovan <ionic@ionic.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jerome Glisse [Mon, 6 Aug 2012 16:32:21 +0000 (12:32 -0400)]
drm/radeon: fence virtual address and free it once idle v4
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: do not reenable crtc after moving vram start address
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
Alex Deucher [Thu, 26 Jul 2012 17:38:52 +0000 (13:38 -0400)]
drm/radeon: properly handle crtc powergating
Need to make sure the crtc is gated on before modesetting.
Explicitly gate the crtc on in prepare() and set a flag
so that the dpms functions don't gate it off during
mode set.
Noticed by sylware on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Arnd Bergmann [Wed, 8 Aug 2012 21:27:58 +0000 (05:27 +0800)]
leds: renesas: fix error handling
86312413 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Pull networking changes from David Miller:
"Most importantly this should cure the ipv4-mapped ipv6 socket TCP
crashes some people were seeing, otherwise:
1) Fix e1000e autonegotiation handling regression, from Tushar Dave.
2) Fix TX data corruption race on e1000e down, also from Tushar Dave.
3) Fix bfin_sir IRDA driver build, from Sonic Zhang.
4) AF_PACKET mmap() tests a flag in the TX ring shared between
userspace and the kernel for an internal consistency check. It
really shouldn't do this to validate the kernel's own behavior
because the user can corrupt it to be any value at all. From
Daniel Borkmann.
5) Fix TCP metrics leak on netns dismantle, from Eric Dumazet.
6) Orphan the anonymous TCP socket from the SKB in
ip_send_unicast_reply() so that the rest of the stack needn't see
it. Otherwise we get selinux problems of all sorts, from Eric
Dumazet.
This is the best way to fix this since the socket is just a place
holder for sending packets in a context where we have no real
socket at all.
7) Fix TUN detach crashes, from Stanislav Kinsbursky.
8) dev_set_alias() leaks memory on krealloc() failure, from Alexey
Khoroshilov.
9) FIB trie must use call_rcu() not call_rcu_bh(), because this code
is not universally invoked from software interrupts. From Eric
Dumazet.
10) PPTP looks up ipv4 routes with the wrong network namespace, fix
from Gao Feng."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
bnx2x: Fix compiler warnings
af_packet: remove BUG statement in tpacket_destruct_skb
macvtap: rcu_dereference outside read-lock section
codel: refine one condition to avoid a nul rec_inv_sqrt
ixgbe: add missing braces
ipv4: fix ip_send_skb()
net: tcp: ipv6_mapped needs sk_rx_dst_set method
ipv4: tcp: unicast_sock should not land outside of TCP stack
bnx2x: Fix recovery flow cleanup during probe
bnx2x: fix unload previous driver flow when flr-capable
tun: don't zeroize sock->file on detach
igb: Fix register defines for all non-82575 hardware
e1000e: fix panic while dumping packets on Tx hang with IOMMU
igb: fix panic while dumping packets on Tx hang with IOMMU
tcp: must free metrics at net dismantle
net/stmmac: mark probe function as __devinit
lpc_eth: remove obsolete ifdefs
net/core: Fix potential memory leak in dev_set_alias()
cdc-phonet: Don't leak in usbpn_open
batman-adv: Fix mem leak in the batadv_tt_local_event() function
...
Linus Torvalds [Mon, 13 Aug 2012 05:40:51 +0000 (08:40 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull tcm_vhost level target fabric driver from Nicholas Bellinger:
"Here is the PULL request for the initial merge of tcm_vhost based on
RFC-v5 code with MST's ACK appended to the initial merge commit."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_vhost: Initial merge for vhost level target fabric driver
Joren Van Onder [Sat, 11 Aug 2012 17:10:35 +0000 (17:10 +0000)]
bnx2x: Fix compiler warnings
Fix the following compiler warnings:
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Joren Van Onder <joren.vanonder@gmail.com> Acked-By: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet: remove BUG statement in tpacket_destruct_skb
Here's a quote of the comment about the BUG macro from asm-generic/bug.h:
Don't use BUG() or BUG_ON() unless there's really no way out; one
example might be detecting data structure corruption in the middle
of an operation that can't be backed out of. If the (sub)system
can somehow continue operating, perhaps with reduced functionality,
it's probably not BUG-worthy.
If you're tempted to BUG(), think again: is completely giving up
really the *only* solution? There are usually better options, where
users don't need to reboot ASAP and can mostly shut down cleanly.
In our case, the status flag of a ring buffer slot is managed from both sides,
the kernel space and the user space. This means that even though the kernel
side might work as expected, the user space screws up and changes this flag
right between the send(2) is triggered when the flag is changed to
TP_STATUS_SENDING and a given skb is destructed after some time. Then, this
will hit the BUG macro. As David suggested, the best solution is to simply
remove this statement since it cannot be used for kernel side internal
consistency checks. I've tested it and the system still behaves /stable/ in
this case, so in accordance with the above comment, we should rather remove it.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_dereference occurs in update section. Replacement by
rcu_dereference_protected in order to prevent lockdep
complaint.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 Aug 2012 18:45:33 +0000 (21:45 +0300)]
Merge tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
Linus Torvalds [Sun, 12 Aug 2012 18:34:09 +0000 (21:34 +0300)]
Merge tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
- Fix for two recent regressions in the generic PM domains framework.
- Revert of a commit that introduced a resume regression and is
conceptually incorrect in my opinion.
- Fix for a return value in pcc-cpufreq.c from Julia Lawall.
- RTC wakeup signaling fix from Neil Brown.
- Suppression of compiler warnings for CONFIG_PM_SLEEP unset in ACPI,
platform/x86 and TPM drivers.
* tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tpm_tis / PM: Fix unused function warning for CONFIG_PM_SLEEP
platform / x86 / PM: Fix unused function warnings for CONFIG_PM_SLEEP
ACPI / PM: Fix unused function warnings for CONFIG_PM_SLEEP
Revert "NMI watchdog: fix for lockup detector breakage on resume"
PM: Make dev_pm_get_subsys_data() always return 0 on success
drivers/cpufreq/pcc-cpufreq.c: fix error return code
RTC: Avoid races between RTC alarm wakeup and suspend.
Linus Torvalds [Sun, 12 Aug 2012 18:31:44 +0000 (21:31 +0300)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
Jeff Mahoney [Fri, 10 Aug 2012 19:07:09 +0000 (15:07 -0400)]
printk: Fix calculation of length used to discard records
While tracking down a weird buffer overflow issue in a program that
looked to be sane, I started double checking the length returned by
syslog(SYSLOG_ACTION_READ_ALL, ...) to make sure it wasn't overflowing
the buffer.
It turns out that the loops that calculate how much space the entries
will take when they're copied don't include the newlines and prefixes
that will be included in the final output since prev flags is passed as
zero.
This patch properly accounts for it and fixes the overflow.
CC: stable@kernel.org Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Vetter [Thu, 9 Aug 2012 20:33:58 +0000 (22:33 +0200)]
drm/i915: don't grab dev->struct_mutex for userspace forcewak
Since forcewake is now protected by a spinlock, we don't need to grab
dev->struct_mutex any more. This way we can also get rid of a stale
comment, noticed by Ben Widawsky while reviewing some locking changes.
v2: Kill the unused variable ret, noticed by Fengguang Wu.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Takashi Iwai [Sat, 11 Aug 2012 06:56:42 +0000 (08:56 +0200)]
drm/i915: Fix blank panel at reopening lid
When you reopen the lid on a laptop with PCH, the panel suddenly goes
blank sometimes. It seems because BLC_PWM_CPU_CTL register is cleared
to zero when BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1 registers are
enabled.
This patch fixes the problem by moving the call of the function setting
BLC_PWM_CPU_CTL after enabling other two registers.
Eric Dumazet [Sun, 29 Jul 2012 20:52:21 +0000 (20:52 +0000)]
codel: refine one condition to avoid a nul rec_inv_sqrt
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
To keep codel_vars_init() as efficient as possible, refine
the condition to make sure rec_inv_sqrt initial value is correct
Many thanks to Anton Mich for discovering the issue and suggesting
a fix.
Reported-by: Anton Mich <lp2s1h@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov [Fri, 10 Aug 2012 07:35:14 +0000 (07:35 +0000)]
ixgbe: add missing braces
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Reported-by: Sascha Wildner <saw@online.de> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Aug 2012 23:26:41 +0000 (16:26 -0700)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Here is a handful of fixes intended for 3.6.
Daniel Drake offers a cfg80211 fix to consume pending events before
taking a wireless device down. This prevents a resource leak.
Stanislaw Gruszka gives us a fix for a NULL pointer dereference in
rt61pci.
Johannes Berg provides an iwlwifi patch to disable "greenfield" mode.
Use of that mode was causing a rate scaling problem in for iwlwifi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paulo Zanoni [Fri, 10 Aug 2012 13:03:03 +0000 (10:03 -0300)]
drm/i915: try harder to find WR PLL clock settings
If we don't find the exact refresh rate, go with the next one. This
makes some modes work for me. They won't have the best settings, but
will at least have something. Just returning from this function when
we don't find the perfect settings does not help us at all.
Version 2:
- Remove duplicate lines on the clock table.
- Add back debug message with refresh, p, n2 and r2.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Fri, 10 Aug 2012 13:05:10 +0000 (10:05 -0300)]
drm/i915: use the correct encoder type when comparing
- intel_encoder->type is INTEL_OUTPUT_SOMETHING
- drm_encoder->encoder_type is DRM_MODE_ENCODER_SOMETHING
Here we're using intel_encoder, so compare the oranges against
oranges. While at it, rename the variable to "intel_encoder" so we
keep our naming standards used everywhere.
Luckily this was not a bug because both DRM_MODE_ENCODER_DAC and
INTEL_OUTPUT_ANALOG are defined as 1. This is the only case where the
drm definition matches the intel definition.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
tpm_tis / PM: Fix unused function warning for CONFIG_PM_SLEEP
According to a compiler warning, the tpm_tis_resume() function is not
used for CONFIG_PM_SLEEP unset, so add a #ifdef to prevent it from
being built in that case.
platform / x86 / PM: Fix unused function warnings for CONFIG_PM_SLEEP
According to compiler warnings, quite some suspend/resume functions
in platform x86 drivers are not used for CONFIG_PM_SLEEP unset, so
add #ifdefs to prevent them from being built in that case.
ACPI / PM: Fix unused function warnings for CONFIG_PM_SLEEP
According to compiler warnings, several suspend/resume functions
in ACPI drivers are not used for CONFIG_PM_SLEEP unset, so add
#ifdefs to prevent them from being built in that case.
ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.
Since this can not possibly work, it's better to disable i2c
support entirely on this board.
Without this patch, building davinci_all_defconfig results in:
arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sekhar Nori <nsekhar@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Andrey Porodko <panda@chelcom.ru>
Arnd Bergmann [Thu, 3 May 2012 12:47:54 +0000 (12:47 +0000)]
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.
Without this patch, building tct_hammer_defconfig results in:
net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)
The size of vmlinux increases by 1.78% because of this:
size obj-arm/vmlinux.nobug
text data bss dec hex filename 2108474 116916 55352 2280742 22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
text data bss dec hex filename 2150804 116916 53696 2321416 236c08 obj-arm/vmlinux
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org>
Arnd Bergmann [Fri, 10 Aug 2012 10:28:57 +0000 (12:28 +0200)]
Merge branch 'testing/new-warnings' into fixes
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Arnd Bergmann [Sat, 4 Aug 2012 07:11:34 +0000 (07:11 +0000)]
omap-rng: fix use of SIMPLE_DEV_PM_OPS
omap_rng_suspend and omap_rng_resume are unused if CONFIG_PM is enabled
but CONFIG_PM_SLEEP is disabled. I found this while building all defconfig
files on ARM. It's not clear to me if this is the right solution, but
at least it makes the code consistent again.
Without this patch, building omap1_defconfig results in:
drivers/char/hw_random/omap-rng.c:165:12: warning: 'omap_rng_suspend' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:171:12: warning: 'omap_rng_resume' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kevin Hilman <khilman@ti.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Herbert Xu <herbert@gondor.apana.org.au>
Arnd Bergmann [Sat, 4 Aug 2012 11:18:20 +0000 (11:18 +0000)]
spi/s3c64xx: improve error handling
When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Cc: Jaswinder Singh <jaswinder.singh@linaro.org> Cc: Grant Likely <grant.likely@secretlab.ca>
projects / kernel.git / log