Arnd Bergmann [Tue, 9 Feb 2021 16:48:04 +0000 (17:48 +0100)]
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: amlogic updates for v5.12
- add thermal zones with cooling configuration
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: add the thermal-zones with cooling configuration
ARM: dts: meson8: add the thermal-zones with cooling configuration
ARM: dts: meson: add the ADC thermal sensor to meson.dtsi
ARM: dts: meson: move iio-hwmon for the SoC temperature to meson.dtsi
Arnd Bergmann [Tue, 9 Feb 2021 16:46:47 +0000 (17:46 +0100)]
Merge tag 'zynqmp-dt-for-v5.12' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: ZynqMP DT changes for v5.12
- Wire clock chips present on boards
- Enable reset, qspi, nand, watchdog and DP IPs
- Enable phy driver for sata and DP
- Add iommu description
- Add support for zcu104 revC+ boards
- Various small changes
- Add missing labels
- Fix typos in documentation
- Add missing boards
* tag 'zynqmp-dt-for-v5.12' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Wire up the DisplayPort subsystem
arm64: dts: zynqmp: Add DisplayPort subsystem
arm64: dts: zynqmp: Add DPDMA node
dt-bindings: arm: Fix typo in zcu111 board
arm64: dts: zynqmp: Add description for zcu104 revC
arm64: dts: zynqmp: Add missing iommu IDs
arm64: dts: zynqmp: Add missing lpd watchdog node
arm64: dts: zynqmp: Wire zynqmp qspi controller
arm64: dts: zynqmp: Wire arasan nand controller
arm64: dts: zynqmp: Add missing mio-bank properties to sdhcis
arm64: dts: zynqmp: Add label for zynqmp_ipi
arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
arm64: dts: zynqmp: Enable reset controller driver
arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
arm64: dts: zynqmp: Add address-cells property to interrupt controllers
Arnd Bergmann [Tue, 9 Feb 2021 16:46:11 +0000 (17:46 +0100)]
Merge tag 'samsung-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.12
1. Use new compatile to properly configure Exynos5420 USB2 PHY, fixing
it suspend/resume cycle.
2. Correct Samsung PMIC interrupt trigger levels on multiple boards.
3. Correct the voltages of Samsung GT-I9100 charger and add top-off
charger.
* tag 'samsung-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add top-off charging regulator node for I9100
ARM: dts: exynos: Fix charging regulator voltage and current for I9100
ARM: dts: exynos: correct PMIC interrupt trigger level on Odroid XU3 family
ARM: dts: exynos: correct PMIC interrupt trigger level on Arndale Octa
ARM: dts: exynos: correct PMIC interrupt trigger level on Spring
ARM: dts: exynos: correct PMIC interrupt trigger level on Rinato
ARM: dts: exynos: correct PMIC interrupt trigger level on Monk
ARM: dts: exynos: correct PMIC interrupt trigger level on Artik 5
ARM: dts: exynos: use Exynos5420 dedicated USB2 PHY compatible
Lubomir Rintel [Thu, 21 Jan 2021 03:41:29 +0000 (04:41 +0100)]
ARM: dts: mmp3-dell-ariel: Replace SSP2 with spi-gpio
The firmware leaves the pins in GPIO mode. Until we have a proper pinmux
driver hooked on we just need to bitbang SPI. No big deal, this is just
used for the power button and performance is not important.
Lubomir Rintel [Thu, 21 Jan 2021 03:41:28 +0000 (04:41 +0100)]
ARM: dts: mmp3-dell-ariel: Add the power button node
This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.
However, while the EC itself is controlled via I2C, the input capability
for the power button acts as a separate device attached to the SPI, hence
it has a separate device node.
Lubomir Rintel [Thu, 21 Jan 2021 03:41:23 +0000 (04:41 +0100)]
ARM: dts: mmp3-dell-ariel: Drop linux,usable-memory from /memory
Drop the linux,usable-memory properties; the schema is unhappy about
them.
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
Arnd Bergmann [Tue, 2 Feb 2021 17:03:54 +0000 (18:03 +0100)]
Merge tag 'mvebu-dt64-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.12 (part 1)
- rename u-boot mtd partition to a53-firmware on Turris Mox (Armada 3720 based)
- improve SDHCI support on AP807 based board
- move SATA comphy into main armada-37xx.dtsi
- add Armada 8K/7K PWM support
* tag 'mvebu-dt64-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada: add pwm offsets for ap/cp gpios
arm64: dts: marvell: armada-37xx: Add SATA comphy into main armada-37xx.dtsi file
arm64: dts: cn913x-db: enable MMC HS400
arm64: dts: change AP807 SDHCI compatibility string
arm64: dts: armada-3720-turris-mox: rename u-boot mtd partition to a53-firmware
Arnd Bergmann [Tue, 2 Feb 2021 17:02:48 +0000 (18:02 +0100)]
Merge tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.12 (part 1)
Improve LED and fan support on Helios4 boad (Armada 388 based)
Add ECC configuration for Linksys board (Aramda 385 based)
* tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada388-helios4: assign pinctrl to each fan
ARM: dts: armada388-helios4: assign pinctrl to LEDs
ARM: dts: armada-385-linksys: fix usage with newer devices
Arnd Bergmann [Tue, 2 Feb 2021 17:00:48 +0000 (18:00 +0100)]
Merge tag 'v5.11-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt6779:
- add DEVAPC node to detect mallicious bus accesses
- add PMIC wrapper node
mt7622:
- add reset to mmc node
mt8183:
- fix typo in drma-fifo-size property
- refine compatible for the disp-gamma
- add phandel of PM domain to the PWM node
- add second PWM node
- add regulator to MFG power domain
- enable DSI node in kukui
- add krane sku0, which uses different panel
- fix mailbox dt-bindings include path
mt8192:
- add NOR flash node
- add PSCI based CPU idle states
mt8516:
- add node for the UART's APDMA controller
* tag 'v5.11-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: Fix GCE include path
dts64: mt7622: fix slow sd card access
dt-bindings: arm64: dts: mediatek: Add krane sku0
arm64: dts: mt8183: Add krane-sku0 board.
arm64: dts: mt8183: config dsi node
arm64: dts: mt6779: Support pwrap on Mediatek MT6779 platform
arm64: dts: mt6779: Support devapc
arm64: dts: mt8192: Add cpu-idle-states
arm64: dts: mediatek: mt8183: Add domain supply for mfg
arm64: dts: mt8192: add nor_flash device node
arm64: dts: mediatek: mt8516: add support for APDMA
arm64: dts: mediatek: mt8183-evb: add PWM support
arm64: dts: mediatek: mt8183: add pwm node
arm64: dts: mt8183: Add missing power-domain for pwm0 node
arm64: dts: mt8183: refine gamma compatible name
arm64: dts: mt8183: rename rdma fifo size
Arnd Bergmann [Tue, 2 Feb 2021 16:58:32 +0000 (17:58 +0100)]
Merge tag 'arm-soc/for-5.12/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.12 please pull the following:
- Rafal continues to add support for the 4906/4908 SoC family and adds
a Device Tree for the Netgear R8000P router (4906-based), describes
the NAND controller of the 4908 more appropriately (based on the older
63138 DSL SoC), describes the 4908 PCIe reset controller, internal
Ethernet switch (Starfighter 2 switch) and finally the Power
Management Bus (PMB)
- Scott removes all of the SATA-related Device Tree nodes since SATA
is unused on the Stingray product line
Arnd Bergmann [Tue, 2 Feb 2021 16:57:14 +0000 (17:57 +0100)]
Merge tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.12, please pull the following:
- Dave adds a proper compatile string for the DSI1 panel on 2711
(Raspberry Pi 4) to permit adequate driver differentiation
- Nicolas declares reserved memory regions filed by the Rasbperry Pi
bootloader to indicate the running system configuration
- Maxime declares the BSC (HDMI I2C controller) and CEC interrupt
controllers
- Stanislav fixes a tab vs. space issue in the BCM21664 DTS
* tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Add the CEC interrupt controller
ARM: dts: bcm21664: Replace spaces with a tab
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration
ARM: dts: bcm2711: Use compatible string for BCM2711 DSI1
Arnd Bergmann [Tue, 2 Feb 2021 16:53:02 +0000 (17:53 +0100)]
Merge tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
- DT fixes spotted through the schemas
- Mali Support for the A10s/A13/GR8/R8
- MMC improvements for the A64 and H6
- New board: SL631 Action Camera, PineTab Early Adopter
* tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (47 commits)
ARM: dts: sunxi: Rename nmi_intc to r_intc
ARM: dts: sun8i: h2-plus: bananapi-m2-zero: Increase BT UART speed
ARM: dts: sunxi: bananapi-m2-plus: Increase BT UART speed
arm64: dts: allwinner: pine-h64: Fix typos in BT GPIOs
arm64: dts: allwinner: pinetab: Fix the panel compatible
arm64: dts: allwinner: pinephone: Remove useless light sensor supplies
arm64: dts: allwinner: h6: Use - instead of @ for DT OPP entries
ARM: dts: sun8i-a33: sina33: Add missing panel power supply
ARM: dts: sun8i-a83t: Remove empty CSI port
ARM: dts: sun8i-s3: pinecube: Fix CSI DTC warnings
ARM: dts: sun8i-s3: impetus: Fix the USB PHY ID detect GPIO properties
ARM: dts: sun8i: nanopi-r1: Fix GPIO regulator state array
ARM: dts: sun6i: primo81: Remove useless io-channel-cells
ARM: dts: sunxi: Fix CPU thermal zone node name
ARM: dts: sunxi: Add missing backlight supply
ARM: dts: sunxi: Fix the LED node names
dt-bindings: rtc: sun6i-a31-rtc: Loosen the requirements on the clocks
dt-bindings: iio: adc: Add AXP803 compatible
dt-bindings: sunxi: Fix the pinecube compatible
ARM: dts: sun8i-v3s: Add CSI0 MCLK pin definition
...
Michal Simek [Thu, 21 Jan 2021 10:27:00 +0000 (11:27 +0100)]
arm64: dts: zynqmp: Add description for zcu104 revC
Xilinx ZynqMP zcu104 revC and newer board revisions have different i2c
structure compare to revA. The rest of the board is the same from software
perspective.
Also enable DMAs and QSPI.
Michal Simek [Thu, 21 Jan 2021 10:26:58 +0000 (11:26 +0100)]
arm64: dts: zynqmp: Add missing lpd watchdog node
Xilinx ZynqMP SoC has FPD (Full Power Domain) and LPD (Low Power Domain)
watchdogs. There are cases where also LPD WDT should be used by Arm cores
that's why list it with disabled status.
Michal Simek [Thu, 21 Jan 2021 10:26:55 +0000 (11:26 +0100)]
arm64: dts: zynqmp: Add missing mio-bank properties to sdhcis
Add missing xlnx,mio-bank property to sdhci nodes. Also add properties with
0 value to have it listed in case that files are copied to different
projects where default case doesn't need to be handled in the same way.
That's why explicitly list them too.
Michal Simek [Thu, 21 Jan 2021 10:26:50 +0000 (11:26 +0100)]
arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
Origin DT binding just specify driver but wasn't aligned with DT binding
which came later. Extend description for zcu102 and zcu106 to cover latest
binding.
Samuel Holland [Mon, 18 Jan 2021 05:50:35 +0000 (23:50 -0600)]
ARM: dts: sunxi: Rename nmi_intc to r_intc
The R_INTC block controls more than just the NMI, and it is a different
hardware block than the NMI INTC found in some other Allwinner SoCs, so
the label "nmi_intc" is inaccurate. Name it "r_intc" to match the
compatible and to match the few references in the vendor documentation.
Maxime Ripard [Thu, 14 Jan 2021 11:35:38 +0000 (12:35 +0100)]
arm64: dts: allwinner: pine-h64: Fix typos in BT GPIOs
The commit 53441b8ef7de ("arm64: dts: allwinner: h6: PineH64 model B:
Add bluetooth") introduced the Bluetooth chip for the PineH64 model B,
but the GPIOs property didn't conform to the binding of the bluetooth
chip. Let's fix this.
Maxime Ripard [Thu, 14 Jan 2021 11:35:37 +0000 (12:35 +0100)]
arm64: dts: allwinner: pinetab: Fix the panel compatible
The commit 7fa40ca7ef61 ("arm64: allwinner: dts: a64: add DT for Early
Adopter's PineTab") introduced an ili9881-based panel device node but
didn't conform to the binding. Fix this.
Fixes: 7fa40ca7ef61 ("arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Jernej Skrabec <jernej.skrabec@siol.net> Link: https://lore.kernel.org/r/20210114113538.1233933-18-maxime@cerno.tech
Maxime Ripard [Thu, 14 Jan 2021 11:35:35 +0000 (12:35 +0100)]
arm64: dts: allwinner: h6: Use - instead of @ for DT OPP entries
DTC and the dt-validate tools report warnings for opp with the format
opp@$frequency: dtc for a missing reg property, and dt-validate since
the binding requires child nodes to have the format opp-$frequency.
Our CSI endpoint trigger some DTC warnings due to the fact that we're
having a single endpoint that doesn't need any reg property, and since
we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Maxime Ripard [Thu, 14 Jan 2021 11:35:31 +0000 (12:35 +0100)]
ARM: dts: sun8i-s3: impetus: Fix the USB PHY ID detect GPIO properties
While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Maxime Ripard [Thu, 14 Jan 2021 11:35:30 +0000 (12:35 +0100)]
ARM: dts: sun8i: nanopi-r1: Fix GPIO regulator state array
Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each voltage state,
which in turns create a validation warning.
Hsin-Yi Wang [Wed, 13 Jan 2021 11:03:59 +0000 (19:03 +0800)]
arm64: dts: mt8183: config dsi node
Config dsi node for mt8183 kukui. Set panel and ports.
Several kukui boards share the same panel property and only compatible
is different. So compatible will be set in board dts for comparison
convenience.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Nicolas Boichat <drinkcat@chromium.org> Link: https://lore.kernel.org/r/20210113110400.616319-1-hsinyi@chromium.org Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Arnd Bergmann [Sat, 30 Jan 2021 11:12:13 +0000 (12:12 +0100)]
Merge tag 'tegra-for-5.12-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.12-rc1
Fixes an issue with HDA codec detection by properly wiring up the
power-domain for the HDA controller. This also fixes one of the USB-C
ports on Jetson AGX Xavier and enables support for audio on various
Tegra210, Tegra186 and Tegra194 boards. The Jetson Nano and Jetson TX1
also gain QSPI support.
* tag 'tegra-for-5.12-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Audio graph sound card for Jetson AGX Xavier
arm64: tegra: Audio graph sound card for Jetson TX2
Revert "arm64: tegra: Disable the ACONNECT for Jetson TX2"
arm64: tegra: Add RT5658 device entry
arm64: tegra: Add support for Jetson Xavier NX with eMMC
arm64: tegra: Prepare for supporting the Jetson Xavier NX with eMMC
arm64: tegra: Enable QSPI on Jetson Xavier NX
arm64: tegra: Add QSPI nodes on Tegra194
arm64: tegra: Enable QSPI on Jetson Nano
arm64: tegra: Audio graph sound card for Jetson Nano and TX1
arm64: tegra: Audio graph header for Tegra210
arm64: tegra: Order nodes alphabetically on Tegra210
arm64: tegra: Enable Jetson-Xavier J512 USB host
arm64: tegra: Add XUSB pad controller's "nvidia,pmc" property on Tegra210
arm64: tegra: Add power-domain for Tegra210 HDA
dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM
Sameer Pujar [Fri, 29 Jan 2021 11:41:09 +0000 (17:11 +0530)]
arm64: tegra: Audio graph sound card for Jetson TX2
Enable support for audio-graph based sound card on Jetson TX2. Based
on the board design following I/O modules are enabled.
* All I2S instances (I2S1 ... I2S6)
* All DSPK instances (DSPK1, DSPK2)
* DMIC1, DMIC2 and DMIC3
Peter Geis [Thu, 7 Jan 2021 16:56:59 +0000 (16:56 +0000)]
ARM: tegra: ouya: Fix eMMC on specific bootloaders
Ouya fails to detect the eMMC module when booted via certain bootloaders.
Fastboot and hard-kexec bootloaders fail while u-boot does not. It was
discovered that the issue manifests if the sdmmc4 alternate configuration
clock pin is input disabled.
Ouya uses sdmmc4 in the primary pin configuration. It is unknown why this
occurs, though it is likely related to other eMMC limitations experienced
on Ouya.
For now, fix it by enabling input on cam_mclk_pcc0.
Fixes: d7195ac5c9c5 ("ARM: tegra: Add device-tree for Ouya") Reported-by: Matt Merhar <mattmerhar@protonmail.com> Tested-by: Matt Merhar <mattmerhar@protonmail.com> Signed-off-by: Peter Geis <pgwipeout@gmail.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Two different SKUs exist for the Jetson Xavier NX module, so document
the compatible strings for both, as well as the developer kits that come
with each of the SKUs.
Baruch Siach [Mon, 11 Jan 2021 11:46:28 +0000 (13:46 +0200)]
arm64: dts: armada: add pwm offsets for ap/cp gpios
The 'marvell,pwm-offset' property of both GPIO blocks (per CP component)
point to the same counter registers offset. The driver will decide how
to use counters A/B.
This is different from the convention of pwm on earlier Armada series
(370/38x). On those systems the assignment of A/B counters to GPIO
blocks is coded in both DT and the driver. The actual behaviour of the
current driver on Armada 8K/7K is the same as earlier systems.
Add also clock properties for base pwm frequency reference.
Pali Rohár [Mon, 18 Jan 2021 09:31:39 +0000 (10:31 +0100)]
arm64: dts: marvell: armada-37xx: Add SATA comphy into main armada-37xx.dtsi file
SATA on A3720 SOC can use only comphy2, so move this definition from board
specific DTS file armada-3720-espressobin.dtsi into main A3720 SOC file
armada-37xx.dtsi.
Marek Behún [Mon, 11 Jan 2021 02:12:43 +0000 (03:12 +0100)]
arm64: dts: armada-3720-turris-mox: rename u-boot mtd partition to a53-firmware
The partition called "u-boot" in reality contains TF-A and U-Boot, and
TF-A is before U-Boot.
Rename this parition to "a53-firmware" to avoid confusion for users,
since they cannot simply build U-Boot from U-Boot repository and flash
the resulting image there. Instead they have to build the firmware with
the sources from the mox-boot-builder repository [1] and flash the
a53-firmware.bin binary there.
[1] https://gitlab.nic.cz/turris/mox-boot-builder
Signed-off-by: Marek Behún <kabel@kernel.org> Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox") Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Arnd Bergmann [Fri, 29 Jan 2021 15:31:24 +0000 (16:31 +0100)]
Merge tag 'omap-for-v5.12/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.12 merge window
This includes the following earlier patches that were considered too
late for v5.11 as discussed between Arnd and me on freenode #armlinux
in December:
- More updates to use cpsw switchdev driver
- Enable gta04 PMIC power management
- Updates for dra7 for ECC support, 1.8GHz speed and keep the
ldo0 regulator always on as specified in the data manual
And then we have the new devicetree changes:
- Configure the original Amazon Echo to for audio
- Configure missing thermal interrupt for omap4430
- Configure mapphone devices for passive thermal cooling, and add
1.2GHz mode.
- Correct omap4430 sgx clock rate to use the runtime Android kernel
value, the earlier value was for a lower power operating point
- Drop turbo mode for 1GHz omap3 variants as we now have passive
cooling configured
- Update email address for Javier
- Add new MYIR Tech Limited board support
* tag 'omap-for-v5.12/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-myirtech-*: Add DT for AM335X MYIR Tech Limited board
ARM: dts: omap3-igep: Change email address in copyright notice
ARM: dts: omap36xx: Remove turbo mode for 1GHz variants
ARM: dts: omap443x: Correct sgx clock to 307.2MHz as used on motorola vendor kernel
ARM: dts: motorola-mapphone: Add 1.2GHz OPP
ARM: dts: motorola-mapphone: Configure lower temperature passive cooling
ARM: dts: Configure missing thermal interrupt for 4430
ARM: dts: omap3-echo: Add speaker sound card support
ARM: dts: dra71-evm: mark ldo0 regulator as always on
ARM: dts: dra76x: add support for OPP_PLUS
ARM: dts: am574x-idk: add support for EMIF1 ECC
ARM: dts: omap3-gta04: fix twl4030-power settings
ARM: dts: am335x-evm/evmsk/icev2: switch to new cpsw switch drv
ARM: dts: am33xx-l4: add dt node for new cpsw switchdev driver
Arnd Bergmann [Fri, 29 Jan 2021 15:29:19 +0000 (16:29 +0100)]
Merge tag 'stm32-dt-for-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.12, round 1
Highlights:
----------
MCU part:
-Rename mmc nodes to match with yaml validation.
MPU part:
-Rename mmc nodes to match with yaml validation.
-Move vdda1v1 & vdda1v8 (used by usbphyc) from boards files
to SoC dtsi file.
-LXA:
-Fix leds schema for yaml validation.
-DH:
-Enable SDMMC1 internal pull-ups and disable CKIN feedabck clock
on DHCOM.
-Add SDMMC1 init state inorder to use some gpios during probing phase.
-Disable KS8851 and FMC on PicoITX board.
* tag 'stm32-dt-for-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
ARM: dts: stm32: remove usbphyc ports vdda1v1 & vdda1v8 on stm32mp15 boards
ARM: dts: stm32: add usbphyc vdda1v1 and vdda1v8 supplies on stm32mp151
ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
ARM: dts: stm32: Rename mmc controller nodes to mmc@
ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM
ARM: dts: stm32: Add additional init state for SDMMC1 pins
ARM: dts: stm32: Disable KS8851 and FMC on PicoITX board
ARM: dts: stm32: Fix schema warnings for pwm-leds on lxa-mc1
ARM: dts: stm32: Disable SDMMC1 CKIN feedback clock on DHCOM
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
ARM: dts: stm32: Fix GPIO hog names on DHCOM
ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
ARM: dts: stm32: Disable WP on DHCOM uSD slot
ARM: dts: stm32: Connect card-detect signal on DHCOM
ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
Rosen Penev [Sat, 5 Dec 2020 00:54:36 +0000 (16:54 -0800)]
ARM: dts: armada-385-linksys: fix usage with newer devices
Newer Linksys boards might come with a Winbond W29N02GV which can be
configured in different ways. Make sure we configure it the same way
as the older chips so everything keeps working.
Arnd Bergmann [Fri, 29 Jan 2021 13:02:49 +0000 (14:02 +0100)]
Merge tag 'renesas-arm-dt-for-v5.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.12 (take two)
- Increase support (SPI, I2C, Ethernet, Serial, MMC) for the R-Car V3U
SoC on the Renesas Falcon board,
- Disable SD functions for plain eMMC,
- A minor fix.
Arnd Bergmann [Fri, 29 Jan 2021 12:57:06 +0000 (13:57 +0100)]
Merge tag 'hisi-arm64-dt-for-5.12v2' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon ARM64 DT updates for 5.12
- Further cleanups of the hisilicon DTS to align with the dtschema
- Add or update the I2C, pinctrl and reset nodes for Hikey970
* tag 'hisi-arm64-dt-for-5.12v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: hi3670.dtsi: add I2C settings
arm64: dts: hisilicon: hikey970-pinctrl.dtsi: add missing pinctrl settings
arm64: dts: hisilicon: hi3670.dtsi: add iomcu_rst
arm64: dts: hisilicon: delete unused property smmu-cb-memtype
arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes
arm64: dts: hisilicon: normalize the node name of the localbus
arm64: dts: hisilicon: normalize the node name of the module thermal
arm64: dts: hisilicon: place clock-names "bus" before "core"
arm64: dts: hisilicon: separate each group of data in the property "ranges"
The I2C buses are not declared at the device tree. As this will
be needed by further patches, add them, keeping all in
disabled state. Per-board settings can override it.
The "smmu-cb-memtype" is a private property developed by the Hisilicon
driver in the early stage and is not used now. So delete it.
Otherwise, below YAML check warnings are reported:
arch/arm64/boot/dts/hisilicon/hip06-d03.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/hisilicon/hip07-d05.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:33 +0000 (11:16 +0800)]
arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes
Currently, the names of several nodes incorrectly match common PHY
provider schema. And the phy-provider.yaml requires them must have
property "#phy-cells". As a result, false positives similar to the
following are reported:
usb2-phy@120: '#phy-cells' is a required property
Change their names slightly so that they do not match pattern:
"^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:31 +0000 (11:16 +0800)]
arm64: dts: hisilicon: normalize the node name of the module thermal
1. Change the node name of the thermal zone to match
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', add suffix "-thermal".
2. Change the node name of the trip point to match
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', delete character "@".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:29 +0000 (11:16 +0800)]
arm64: dts: hisilicon: separate each group of data in the property "ranges"
Do not write the "ranges" of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported:
Amelie Delaunay [Thu, 14 Jan 2021 13:15:24 +0000 (14:15 +0100)]
ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
usbphyc is a 48Mhz clock provider: the clock can be used as clock source
for USB OTG. Add #clock-cells property to usbphyc node to reflect this
capability.
vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs.
Remove them from usbphyc child phy nodes now that they are managed in
usbphyc parent node at SoC level.