Greentime Hu [Tue, 4 May 2021 10:59:36 +0000 (18:59 +0800)]
clk: sifive: Use reset-simple in prci driver for PCIe driver
We use reset-simple in this patch so that pcie driver can use
devm_reset_control_get() to get this reset data structure and use
reset_control_deassert() to deassert pcie_power_up_rst_n.
Linus Torvalds [Sat, 6 Mar 2021 01:27:59 +0000 (17:27 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Nothing special here, though Bob's regression fixes for rxe would have
made it before the rc cycle had there not been such strong winter
weather!
- Fix corner cases in the rxe reference counting cleanup that are
causing regressions in blktests for SRP
- Two kdoc fixes so W=1 is clean
- Missing error return in error unwind for mlx5
- Wrong lock type nesting in IB CM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/rxe: Fix errant WARN_ONCE in rxe_completer()
RDMA/rxe: Fix extra deref in rxe_rcv_mcast_pkt()
RDMA/rxe: Fix missed IB reference counting in loopback
RDMA/uverbs: Fix kernel-doc warning of _uverbs_alloc
RDMA/mlx5: Set correct kernel-doc identifier
IB/mlx5: Add missing error code
RDMA/rxe: Fix missing kconfig dependency on CRYPTO
RDMA/cm: Fix IRQ restore in ib_send_cm_sidr_rep
Linus Torvalds [Sat, 6 Mar 2021 01:23:03 +0000 (17:23 -0800)]
Merge tag 'gcc-plugins-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc-plugins fixes from Kees Cook:
"Tiny gcc-plugin fixes for v5.12-rc2. These issues are small but have
been reported a couple times now by static analyzers, so best to get
them fixed to reduce the noise. :)
- Fix coding style issues (Jason Yan)"
* tag 'gcc-plugins-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: latent_entropy: remove unneeded semicolon
gcc-plugins: structleak: remove unneeded variable 'ret'
Linus Torvalds [Sat, 6 Mar 2021 01:21:25 +0000 (17:21 -0800)]
Merge tag 'pstore-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fixes from Kees Cook:
- Rate-limit ECC warnings (Dmitry Osipenko)
- Fix error path check for NULL (Tetsuo Handa)
* tag 'pstore-v5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/ram: Rate-limit "uncorrectable error in header" message
pstore: Fix warning in pstore_kill_sb()
Linus Torvalds [Fri, 5 Mar 2021 21:25:23 +0000 (13:25 -0800)]
Merge tag 'for-5.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Fix DM verity target's optional Forward Error Correction (FEC) for
Reed-Solomon roots that are unaligned to block size"
* tag 'for-5.12/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm verity: fix FEC for RS roots unaligned to block size
dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size
Linus Torvalds [Fri, 5 Mar 2021 20:59:37 +0000 (12:59 -0800)]
Merge tag 'block-5.12-2021-03-05' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe fixes:
- more device quirks (Julian Einwag, Zoltán Böszörményi, Pascal
Terjan)
- fix a hwmon error return (Daniel Wagner)
- fix the keep alive timeout initialization (Martin George)
- ensure the model_number can't be changed on a used subsystem
(Max Gurtovoy)
- rsxx missing -EFAULT on copy_to_user() failure (Dan)
- rsxx remove unused linux.h include (Tian)
- kill unused RQF_SORTED (Jean)
- updated outdated BFQ comments (Joseph)
- revert work-around commit for bd_size_lock, since we removed the
offending user in this merge window (Damien)
* tag 'block-5.12-2021-03-05' of git://git.kernel.dk/linux-block:
nvmet: model_number must be immutable once set
nvme-fabrics: fix kato initialization
nvme-hwmon: Return error code when registration fails
nvme-pci: add quirks for Lexar 256GB SSD
nvme-pci: mark Kingston SKC2000 as not supporting the deepest power state
nvme-pci: mark Seagate Nytro XM1440 as QUIRK_NO_NS_DESC_LIST.
rsxx: Return -EFAULT if copy_to_user() fails
block/bfq: update comments and default value in docs for fifo_expire
rsxx: remove unused including <linux/version.h>
block: Drop leftover references to RQF_SORTED
block: revert "block: fix bd_size_lock use"
Linus Torvalds [Fri, 5 Mar 2021 20:44:43 +0000 (12:44 -0800)]
Merge tag 'io_uring-5.12-2021-03-05' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A bit of a mix between fallout from the worker change, cleanups and
reductions now possible from that change, and fixes in general. In
detail:
- Fully serialize manager and worker creation, fixing races due to
that.
- Clean up some naming that had gone stale.
- SQPOLL fixes.
- Fix race condition around task_work rework that went into this
merge window.
- Implement unshare. Used for when the original task does unshare(2)
or setuid/seteuid and friends, drops the original workers and forks
new ones.
- Drop the only remaining piece of state shuffling we had left, which
was cred. Move it into issue instead, and we can drop all of that
code too.
- Kill f_op->flush() usage. That was such a nasty hack that we had
out of necessity, we no longer need it.
- Following from ->flush() removal, we can also drop various bits of
ctx state related to SQPOLL and cancelations.
- Fix an issue with IOPOLL retry, which originally was fallout from a
filemap change (removing iov_iter_revert()), but uncovered an issue
with iovec re-import too late.
- Fix an issue with system suspend.
- Use xchg() for fallback work, instead of cmpxchg().
- Properly destroy io-wq on exec.
- Add create_io_thread() core helper, and use that in io-wq and
io_uring. This allows us to remove various silly completion events
related to thread setup.
- A few error handling fixes.
This should be the grunt of fixes necessary for the new workers, next
week should be quieter. We've got a pending series from Pavel on
cancelations, and how tasks and rings are indexed. Outside of that,
should just be minor fixes. Even with these fixes, we're still killing
a net ~80 lines"
* tag 'io_uring-5.12-2021-03-05' of git://git.kernel.dk/linux-block: (41 commits)
io_uring: don't restrict issue_flags for io_openat
io_uring: make SQPOLL thread parking saner
io-wq: kill hashed waitqueue before manager exits
io_uring: clear IOCB_WAITQ for non -EIOCBQUEUED return
io_uring: don't keep looping for more events if we can't flush overflow
io_uring: move to using create_io_thread()
kernel: provide create_io_thread() helper
io_uring: reliably cancel linked timeouts
io_uring: cancel-match based on flags
io-wq: ensure all pending work is canceled on exit
io_uring: ensure that threads freeze on suspend
io_uring: remove extra in_idle wake up
io_uring: inline __io_queue_async_work()
io_uring: inline io_req_clean_work()
io_uring: choose right tctx->io_wq for try cancel
io_uring: fix -EAGAIN retry with IOPOLL
io-wq: fix error path leak of buffered write hash map
io_uring: remove sqo_task
io_uring: kill sqo_dead and sqo submission halting
io_uring: ignore double poll add on the same waitqueue head
...
Linus Torvalds [Fri, 5 Mar 2021 20:36:33 +0000 (12:36 -0800)]
Merge tag 'pm-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix the usage of device links in the runtime PM core code and
update the DTPM (Dynamic Thermal Power Management) feature added
recently.
Specifics:
- Make the runtime PM core code avoid attempting to suspend supplier
devices before updating the PM-runtime status of a consumer to
'suspended' (Rafael Wysocki).
- Fix DTPM (Dynamic Thermal Power Management) root node
initialization and label that feature as EXPERIMENTAL in Kconfig
(Daniel Lezcano)"
* tag 'pm-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap/drivers/dtpm: Add the experimental label to the option description
powercap/drivers/dtpm: Fix root node initialization
PM: runtime: Update device status before letting suppliers suspend
Linus Torvalds [Fri, 5 Mar 2021 20:32:17 +0000 (12:32 -0800)]
Merge tag 'acpi-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Make the empty stubs of some helper functions used when CONFIG_ACPI is
not set actually match those functions (Andy Shevchenko)"
* tag 'acpi-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: bus: Constify is_acpi_node() and friends (part 2)
Linus Torvalds [Fri, 5 Mar 2021 20:26:24 +0000 (12:26 -0800)]
Merge tag 'iommu-fixes-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix a sleeping-while-atomic issue in the AMD IOMMU code
- Disable lazy IOTLB flush for untrusted devices in the Intel VT-d
driver
- Fix status code definitions for Intel VT-d
- Fix IO Page Fault issue in Tegra IOMMU driver
* tag 'iommu-fixes-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix status code for Allocate/Free PASID command
iommu: Don't use lazy flush for untrusted device
iommu/tegra-smmu: Fix mc errors on tegra124-nyan
iommu/amd: Fix sleeping in atomic in increase_address_space()
Linus Torvalds [Fri, 5 Mar 2021 20:21:14 +0000 (12:21 -0800)]
Merge tag 'for-5.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"More regression fixes and stabilization.
Regressions:
- zoned mode
- count zone sizes in wider int types
- fix space accounting for read-only block groups
- subpage: fix page tail zeroing
Fixes:
- fix spurious warning when remounting with free space tree
- fix warning when creating a directory with smack enabled
- ioctl checks for qgroup inheritance when creating a snapshot
- qgroup
- fix missing unlock on error path in zero range
- fix amount of released reservation on error
- fix flushing from unsafe context with open transaction,
potentially deadlocking
- minor build warning fixes"
* tag 'for-5.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: do not account freed region of read-only block group as zone_unusable
btrfs: zoned: use sector_t for zone sectors
btrfs: subpage: fix the false data csum mismatch error
btrfs: fix warning when creating a directory with smack enabled
btrfs: don't flush from btrfs_delayed_inode_reserve_metadata
btrfs: export and rename qgroup_reserve_meta
btrfs: free correct amount of space in btrfs_delayed_inode_reserve_metadata
btrfs: fix spurious free_space_tree remount warning
btrfs: validate qgroup inherit for SNAP_CREATE_V2 ioctl
btrfs: unlock extents in btrfs_zero_range in case of quota reservation errors
btrfs: ref-verify: use 'inline void' keyword ordering
Linus Torvalds [Fri, 5 Mar 2021 20:12:28 +0000 (12:12 -0800)]
Merge tag 'devicetree-fixes-for-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Another batch of graph and video-interfaces schema conversions
- Drop DT header symlink for dropped C6X arch
- Fix bcm2711-hdmi schema error
* tag 'devicetree-fixes-for-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: media: Use graph and video-interfaces schemas, round 2
dts: drop dangling c6x symlink
dt-bindings: bcm2711-hdmi: Fix broken schema
Linus Torvalds [Fri, 5 Mar 2021 20:04:59 +0000 (12:04 -0800)]
Merge tag 'trace-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Functional fixes:
- Fix big endian conversion for arm64 in recordmcount processing
- Fix timestamp corruption in ring buffer on discarding events
- Fix memory leak in __create_synth_event()
- Skip selftests if tracing is disabled as it will cause them to
fail.
Non-functional fixes:
- Fix help text in Kconfig
- Remove duplicate prototype for trace_empty()
- Fix stale comment about the trace_event_call flags.
Self test update:
- Add more information to the validation output of when a corrupt
timestamp is found in the ring buffer, and also trigger a warning
to make sure that tests catch it"
* tag 'trace-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix comment about the trace_event_call flags
tracing: Skip selftests if tracing is disabled
tracing: Fix memory leak in __create_synth_event()
ring-buffer: Add a little more information and a WARN when time stamp going backwards is detected
ring-buffer: Force before_stamp and write_stamp to be different on discard
tracing: Fix help text of TRACEPOINT_BENCHMARK in Kconfig
tracing: Remove duplicate declaration from trace.h
ftrace: Have recordmcount use w8 to read relp->r_info in arm64_is_fake_mcount
Bob Pearson [Thu, 4 Mar 2021 19:20:49 +0000 (13:20 -0600)]
RDMA/rxe: Fix errant WARN_ONCE in rxe_completer()
In rxe_comp.c in rxe_completer() the function free_pkt() did not clear skb
which triggered a warning at 'done:' and could possibly at 'exit:'. The
WARN_ONCE() calls are not actually needed. The call to free_pkt() is
moved to the end to clearly show that all skbs are freed.
Bob Pearson [Thu, 4 Mar 2021 19:20:49 +0000 (13:20 -0600)]
RDMA/rxe: Fix extra deref in rxe_rcv_mcast_pkt()
rxe_rcv_mcast_pkt() dropped a reference to ib_device when no error
occurred causing an underflow on the reference counter. This code is
cleaned up to be clearer and easier to read.
Bob Pearson [Thu, 4 Mar 2021 19:20:49 +0000 (13:20 -0600)]
RDMA/rxe: Fix missed IB reference counting in loopback
When the noted patch below extending the reference taken by
rxe_get_dev_from_net() in rxe_udp_encap_recv() until each skb is freed it
was not matched by a reference in the loopback path resulting in
underflows.
Pavel Begunkov [Sun, 28 Feb 2021 22:35:14 +0000 (22:35 +0000)]
io_uring: don't restrict issue_flags for io_openat
07c2820f7bfdf ("io_uring: replace force_nonblock with flags") did
something strange for io_openat() slicing all issue_flags but
IO_URING_F_NONBLOCK. Not a bug for now, but better to just forward the
flags.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 5 Mar 2021 16:13:07 +0000 (09:13 -0700)]
Merge tag 'nvme-5.12-2021-03-05' of git://git.infradead.org/nvme into block-5.12
Pull NVMe fixes from Christoph:
"nvme fixes for 5.12:
- more device quirks (Julian Einwag, Zoltán Böszörményi, Pascal Terjan)
- fix a hwmon error return (Daniel Wagner)
- fix the keep alive timeout initialization (Martin George)
- ensure the model_number can't be changed on a used subsystem
(Max Gurtovoy)"
* tag 'nvme-5.12-2021-03-05' of git://git.infradead.org/nvme:
nvmet: model_number must be immutable once set
nvme-fabrics: fix kato initialization
nvme-hwmon: Return error code when registration fails
nvme-pci: add quirks for Lexar 256GB SSD
nvme-pci: mark Kingston SKC2000 as not supporting the deepest power state
nvme-pci: mark Seagate Nytro XM1440 as QUIRK_NO_NS_DESC_LIST.
Jens Axboe [Fri, 5 Mar 2021 15:44:39 +0000 (08:44 -0700)]
io_uring: make SQPOLL thread parking saner
We have this weird true/false return from parking, and then some of the
callers decide to look at that. It can lead to unbalanced parks and
sqd locking. Have the callers check the thread status once it's parked.
We know we have the lock at that point, so it's either valid or it's NULL.
Fix race with parking on thread exit. We need to be careful here with
ordering of the sdq->lock and the IO_SQ_THREAD_SHOULD_PARK bit.
Rename sqd->completion to sqd->parked to reflect that this is the only
thing this completion event doesn.
Jens Axboe [Fri, 5 Mar 2021 15:14:08 +0000 (08:14 -0700)]
io-wq: kill hashed waitqueue before manager exits
If we race with shutting down the io-wq context and someone queueing
a hashed entry, then we can exit the manager with it armed. If it then
triggers after the manager has exited, we can have a use-after-free where
io_wqe_hash_wake() attempts to wake a now gone manager process.
Move the killing of the hashed write queue into the manager itself, so
that we know we've killed it before the task exits.
Fixes: 2017d6507bc5 ("io-wq: make buffered file write hashed work map per-ctx") Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 5 Mar 2021 04:02:58 +0000 (21:02 -0700)]
io_uring: clear IOCB_WAITQ for non -EIOCBQUEUED return
The callback can only be armed, if we get -EIOCBQUEUED returned. It's
important that we clear the WAITQ bit for other cases, otherwise we can
queue for async retry and filemap will assume that we're armed and
return -EAGAIN instead of just blocking for the IO.
Jens Axboe [Fri, 5 Mar 2021 00:15:48 +0000 (17:15 -0700)]
io_uring: don't keep looping for more events if we can't flush overflow
It doesn't make sense to wait for more events to come in, if we can't
even flush the overflow we already have to the ring. Return -EBUSY for
that condition, just like we do for attempts to submit with overflow
pending.
Jens Axboe [Thu, 4 Mar 2021 19:39:36 +0000 (12:39 -0700)]
io_uring: move to using create_io_thread()
This allows us to do task creation and setup without needing to use
completions to try and synchronize with the starting thread. Get rid of
the old io_wq_fork_thread() wrapper, and the 'wq' and 'worker' startup
completion events - we can now do setup before the task is running.
Max Gurtovoy [Wed, 17 Feb 2021 17:19:40 +0000 (17:19 +0000)]
nvmet: model_number must be immutable once set
In case we have already established connection to nvmf target, it
shouldn't be allowed to change the model_number. E.g. if someone will
identify ctrl and get model_number of "my_model" later on will change
the model_numbel via configfs to "my_new_model" this will break the NVMe
specification for "Get Log Page – Persistent Event Log" that refers to
Model Number as: "This field contains the same value as reported in the
Model Number field of the Identify Controller data structure, bytes
63:24."
Although it doesn't mentioned explicitly that this field can't be
changed, we can assume it.
So allow setting this field only once: using configfs or in the first
identify ctrl operation.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Martin George [Thu, 11 Feb 2021 17:58:26 +0000 (23:28 +0530)]
nvme-fabrics: fix kato initialization
Currently kato is initialized to NVME_DEFAULT_KATO for both
discovery & i/o controllers. This is a problem specifically
for non-persistent discovery controllers since it always ends
up with a non-zero kato value. Fix this by initializing kato
to zero instead, and ensuring various controllers are assigned
appropriate kato values as follows:
non-persistent controllers - kato set to zero
persistent controllers - kato set to NVMF_DEV_DISC_TMO
(or any positive int via nvme-cli)
i/o controllers - kato set to NVME_DEFAULT_KATO
(or any positive int via nvme-cli)
Signed-off-by: Martin George <marting@netapp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Daniel Wagner [Fri, 12 Feb 2021 09:30:15 +0000 (10:30 +0100)]
nvme-hwmon: Return error code when registration fails
The hwmon pointer wont be NULL if the registration fails. Though the
exit code path will assign it to ctrl->hwmon_device. Later
nvme_hwmon_exit() will try to free the invalid pointer. Avoid this by
returning the error code from hwmon_device_register_with_info().
Fixes: e84de5d06ec4 ("nvme/hwmon: rework to avoid devm allocation") Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme-pci: mark Kingston SKC2000 as not supporting the deepest power state
My 2TB SKC2000 showed the exact same symptoms that were provided
in 7f3d0efba5 ("nvme-pci: avoid the deepest sleep state on
Kingston A2000 SSDs"), i.e. a complete NVME lockup that needed
cold boot to get it back.
According to some sources, the A2000 is simply a rebadged
SKC2000 with a slightly optimized firmware.
Adding the SKC2000 PCI ID to the quirk list with the same workaround
as the A2000 made my laptop survive a 5 hours long Yocto bootstrap
buildfest which reliably triggered the SSD lockup previously.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Fri, 5 Mar 2021 03:06:28 +0000 (19:06 -0800)]
Merge tag 'drm-fixes-2021-03-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"More may show up but this is what I have at this stage: just a single
nouveau regression fix, and a bunch of amdgpu fixes.
amdgpu:
- S0ix fix
- Handle new NV12 SKU
- Misc power fixes
- Display uninitialized value fix
- PCIE debugfs register access fix
nouveau:
- regression fix for gk104"
* tag 'drm-fixes-2021-03-05' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: fix parameter error of RREG32_PCIE() in amdgpu_regs_pcie
drm/amd/display: fix the return of the uninitialized value in ret
drm/amdgpu: enable BACO runpm by default on sienna cichlid and navy flounder
drm/amd/pm: correct Arcturus mmTHM_BACO_CNTL register address
drm/amdgpu/swsmu/vangogh: Only use RLCPowerNotify msg for disable
drm/amdgpu/pm: make unsupported power profile messages debug
drm/amdgpu:disable VCN for Navi12 SKU
drm/amdgpu: Only check for S0ix if AMD_PMC is configured
drm/nouveau/fifo/gk104-gp1xx: fix creation of sw class
Linus Torvalds [Fri, 5 Mar 2021 02:53:30 +0000 (18:53 -0800)]
Merge tag 'mkp-scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi
Pull iSCSI fixes from Martin Petersen:
"Three fixes for missed iSCSI verification checks (and make the sysfs
files use "sysfs_emit()" - that's what it is there for)"
* tag 'mkp-scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi:
scsi: iscsi: Verify lengths on passthrough PDUs
scsi: iscsi: Ensure sysfs attributes are limited to PAGE_SIZE
scsi: iscsi: Restrict sessions and handles to admin capabilities
Dave Airlie [Fri, 5 Mar 2021 00:55:57 +0000 (10:55 +1000)]
Merge branch '00.00-inst' of git://github.com/skeggsb/linux into drm-fixes
A single regression fix here that I noticed while testing a bunch of
boards for something else, not sure where this got lost! Prevents 3D
driver from initialising on some GPUs.
Chris Leech [Wed, 24 Feb 2021 05:39:01 +0000 (21:39 -0800)]
scsi: iscsi: Verify lengths on passthrough PDUs
Open-iSCSI sends passthrough PDUs over netlink, but the kernel should be
verifying that the provided PDU header and data lengths fall within the
netlink message to prevent accessing beyond that in memory.
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chris Leech [Wed, 24 Feb 2021 02:00:17 +0000 (18:00 -0800)]
scsi: iscsi: Ensure sysfs attributes are limited to PAGE_SIZE
As the iSCSI parameters are exported back through sysfs, it should be
enforcing that they never are more than PAGE_SIZE (which should be more
than enough) before accepting updates through netlink.
Change all iSCSI sysfs attributes to use sysfs_emit().
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lee Duncan [Tue, 23 Feb 2021 21:06:24 +0000 (13:06 -0800)]
scsi: iscsi: Restrict sessions and handles to admin capabilities
Protect the iSCSI transport handle, available in sysfs, by requiring
CAP_SYS_ADMIN to read it. Also protect the netlink socket by restricting
reception of messages to ones sent with CAP_SYS_ADMIN. This disables
normal users from being able to end arbitrary iSCSI sessions.
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Chris Leech <cleech@redhat.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jens Axboe [Thu, 4 Mar 2021 19:21:05 +0000 (12:21 -0700)]
kernel: provide create_io_thread() helper
Provide a generic helper for setting up an io_uring worker. Returns a
task_struct so that the caller can do whatever setup is needed, then call
wake_up_new_task() to kick it into gear.
Add a kernel_clone_args member, io_thread, which tells copy_process() to
mark the task with PF_IO_WORKER.
Pavel Begunkov [Thu, 4 Mar 2021 13:59:25 +0000 (13:59 +0000)]
io_uring: reliably cancel linked timeouts
Linked timeouts are fired asynchronously (i.e. soft-irq), and use
generic cancellation paths to do its stuff, including poking into io-wq.
The problem is that it's racy to access tctx->io_wq, as
io_uring_task_cancel() and others may be happening at this exact moment.
Mark linked timeouts with REQ_F_INLIFGHT for now, making sure there are
no timeouts before io-wq destraction.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Thu, 4 Mar 2021 13:59:24 +0000 (13:59 +0000)]
io_uring: cancel-match based on flags
Instead of going into request internals, like checking req->file->f_op,
do match them based on REQ_F_INFLIGHT, it's set only when we want it to
be reliably cancelled.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Milan Broz [Tue, 23 Feb 2021 20:21:21 +0000 (21:21 +0100)]
dm verity: fix FEC for RS roots unaligned to block size
Optional Forward Error Correction (FEC) code in dm-verity uses
Reed-Solomon code and should support roots from 2 to 24.
The error correction parity bytes (of roots lengths per RS block) are
stored on a separate device in sequence without any padding.
Currently, to access FEC device, the dm-verity-fec code uses dm-bufio
client with block size set to verity data block (usually 4096 or 512
bytes).
Because this block size is not divisible by some (most!) of the roots
supported lengths, data repair cannot work for partially stored parity
bytes.
This fix changes FEC device dm-bufio block size to "roots << SECTOR_SHIFT"
where we can be sure that the full parity data is always available.
(There cannot be partial FEC blocks because parity must cover whole
sectors.)
Because the optional FEC starting offset could be unaligned to this
new block size, we have to use dm_bufio_set_sector_offset() to
configure it.
The problem is easily reproduced using veritysetup, e.g. for roots=13:
# create an erasure that should be always repairable with this roots setting
dd if=/dev/zero of=data.img conv=notrunc bs=1 count=8 seek=4088 status=none
# try to read it through dm-verity
veritysetup open data.img test hash.img --fec-device=fec.img --fec-roots=13 $(cat roothash)
dd if=/dev/mapper/test of=/dev/null bs=4096 status=noxfer
# wait for possible recursive recovery in kernel
udevadm settle
veritysetup close test
With this fix, errors are properly repaired.
device-mapper: verity-fec: 7:1: FEC 0: corrected 8 errors
...
Without it, FEC code usually ends on unrecoverable failure in RS decoder:
device-mapper: verity-fec: 7:1: FEC 0: failed to correct: -74
...
This problem is present in all kernels since the FEC code's
introduction (kernel 4.5).
It is thought that this problem is not visible in Android ecosystem
because it always uses a default RS roots=2.
Depends-on: bf977172bbaa ("dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size") Signed-off-by: Milan Broz <gmazyland@gmail.com> Tested-by: Jérôme Carretero <cJ-ko@zougloub.eu> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Cc: stable@vger.kernel.org # 4.5+ Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Mikulas Patocka [Tue, 23 Feb 2021 20:21:20 +0000 (21:21 +0100)]
dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size
dm_bufio_get_device_size returns the device size in blocks. Before
returning the value, we must subtract the nubmer of starting
sectors. The number of starting sectors may not be divisible by block
size.
Note that currently, no target is using dm_bufio_set_sector_offset and
dm_bufio_get_device_size simultaneously, so this change has no effect.
However, an upcoming dm-verity-fec fix needs this change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Linus Torvalds [Thu, 4 Mar 2021 19:26:17 +0000 (11:26 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- Doc fixes
- selftests fixes
- Add runstate information to the new Xen support
- Allow compiling out the Xen interface
- 32-bit PAE without EPT bugfix
- NULL pointer dereference bugfix
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Clear the CR4 register on reset
KVM: x86/xen: Add support for vCPU runstate information
KVM: x86/xen: Fix return code when clearing vcpu_info and vcpu_time_info
selftests: kvm: Mmap the entire vcpu mmap area
KVM: Documentation: Fix index for KVM_CAP_PPC_DAWR1
KVM: x86: allow compiling out the Xen hypercall interface
KVM: xen: flush deferred static key before checking it
KVM: x86/mmu: Set SPTE_AD_WRPROT_ONLY_MASK if and only if PML is enabled
KVM: x86: hyper-v: Fix Hyper-V context null-ptr-deref
KVM: x86: remove misplaced comment on active_mmu_pages
KVM: Documentation: rectify rst markup in kvm_run->flags
Documentation: kvm: fix messy conversion from .txt to .rst
Linus Torvalds [Thu, 4 Mar 2021 19:24:47 +0000 (11:24 -0800)]
Merge tag 'for-linus-5.12b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two security issues (XSA-367 and XSA-369)"
* tag 'for-linus-5.12b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: fix p2m size in dom0 for disabled memory hotplug case
xen-netback: respect gnttab_map_refs()'s return value
Xen/gnttab: handle p2m update errors on a per-slot basis
Linus Torvalds [Thu, 4 Mar 2021 19:18:13 +0000 (11:18 -0800)]
Merge tag 'sound-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Slightly bulky changes are seen at this time, mostly for dealing with
the messed up Kconfig for ASoC Intel SOF stuff. The driver and its
code was split to each module per platform now, which is far more
straightforward. This should cover the randconfig problems, and more
importantly, improve the actual device handling as well.
Other than that, nothing particular stands out: the HDMI PCM
assignment fix for Intel Tigerlake, MIPS n64 error handling fix, and
the usual suspects, HD-audio / USB-audio quirks"
* tag 'sound-5.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek: Apply dual codec quirks for MSI Godlike X570 board
ALSA: hda/realtek: Add quirk for Intel NUC 10
ALSA: hda/hdmi: let new platforms assign the pcm slot dynamically
ALSA: hda/realtek: Add quirk for Clevo NH55RZQ
ALSA: hda: intel-sdw-acpi: add missing include files
ALSA: hda: move Intel SoundWire ACPI scan to dedicated module
ASoC: SOF: Intel: SoundWire: simplify Kconfig
ASoC: SOF: pci: move DSP_CONFIG use to platform-specific drivers
ASoC: SOF: pci: split PCI into different drivers
ASoC: SOF: ACPI: avoid reverse module dependency
ASoC: soc-acpi: allow for partial match in parent name
ALSA: hda: intel-nhlt: verify config type
ALSA: hda: fix kernel-doc warnings
ALSA: usb-audio: Fix Pioneer DJM devices URB_CONTROL request direction to set samplerate
ALSA: usb-audio: use Corsair Virtuoso mapping for Corsair Virtuoso SE
ALSA: hda/realtek: Enable headset mic of Acer SWIFT with ALC256
ALSA: ctxfi: cthw20k2: fix mask on conf to allow 4 bits
ALSA: usb-audio: Allow modifying parameters with succeeding hw_params calls
ALSA: usb-audio: Drop bogus dB range in too low level
ALSA: usb-audio: Don't abort even if the clock rate differs
...
Naohiro Aota [Wed, 3 Mar 2021 08:55:48 +0000 (17:55 +0900)]
btrfs: zoned: do not account freed region of read-only block group as zone_unusable
We migrate zone unusable bytes to read-only bytes when a block group is
set to read-only, and account all the free region as bytes_readonly.
Thus, we should not increase block_group->zone_unusable when the block
group is read-only.
Fixes: be18ded18d80 ("btrfs: zoned: track unusable bytes for zones") Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Wed, 3 Mar 2021 08:55:46 +0000 (17:55 +0900)]
btrfs: zoned: use sector_t for zone sectors
We need to use sector_t for zone_sectors, or it would set the zone size
to zero when the size >= 4GB (= 2^24 sectors) by shifting the
zone_sectors value by SECTOR_SHIFT. We're assuming zones sizes up to
8GiB.
Fixes: d89afd871112 ("btrfs: get zone information of zoned block devices") Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
tracing: Fix comment about the trace_event_call flags
In the declaration of the struct trace_event_call, the flags has the bits
defined in the comment above it. But these bits are also defined by the
TRACE_EVENT_FL_* enums just above the declaration of the struct. As the
comment about the flags in the struct has become stale and incorrect, just
replace it with a reference to the TRACE_EVENT_FL_* enum above.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If tracing is disabled for some reason (traceoff_on_warning, command line,
etc), the ftrace selftests are guaranteed to fail, as their results are
defined by trace data in the ring buffers. If the ring buffers are turned
off, the tests will fail, due to lack of data.
Because tracing being disabled is for a specific reason (warning, user
decided to, etc), it does not make sense to enable tracing to run the self
tests, as the test output may corrupt the reason for the tracing to be
disabled.
Instead, simply skip the self tests and report that they are being skipped
due to tracing being disabled.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In __create_synth_event(), while iterating field/type arguments, the
argv_split() will return array of atleast 2 elements even when zero
arguments(argc=0) are passed. for e.g. when there is double delimiter
or string ends with delimiter
ring-buffer: Add a little more information and a WARN when time stamp going backwards is detected
When the CONFIG_RING_BUFFER_VALIDATE_TIME_DELTAS is enabled, and the time
stamps are detected as not being valid, it reports information about the
write stamp, but does not show the before_stamp which is still useful
information. Also, it should give a warning once, such that tests detect
this happening.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
ring-buffer: Force before_stamp and write_stamp to be different on discard
Part of the logic of the new time stamp code depends on the before_stamp and
the write_stamp to be different if the write_stamp does not match the last
event on the buffer, as it will be used to calculate the delta of the next
event written on the buffer.
The discard logic depends on this, as the next event to come in needs to
inject a full timestamp as it can not rely on the last event timestamp in
the buffer because it is unknown due to events after it being discarded. But
by changing the write_stamp back to the time before it, it forces the next
event to use a full time stamp, instead of relying on it.
The issue came when a full time stamp was used for the event, and
rb_time_delta() returns zero in that case. The update to the write_stamp
(which subtracts delta) made it not change. Then when the event is removed
from the buffer, because the before_stamp and write_stamp still match, the
next event written would calculate its delta from the write_stamp, but that
would be wrong as the write_stamp is of the time of the event that was
discarded.
In the case that the delta change being made to write_stamp is zero, set the
before_stamp to zero as well, and this will force the next event to inject a
full timestamp and not use the current write_stamp.
Cc: stable@vger.kernel.org Fixes: e6cc5f23410ef ("ring-buffer: Have nested events still record running time stamp") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Jens Axboe [Wed, 3 Mar 2021 22:47:04 +0000 (15:47 -0700)]
io-wq: ensure all pending work is canceled on exit
If we race on shutting down the io-wq, then we should ensure that any
work that was queued after workers shutdown is canceled. Harden the
add work check a bit too, checking for IO_WQ_BIT_EXIT and cancel if
it's set.
Add a WARN_ON() for having any work before we kill the io-wq context.
Play nice and ensure that any thread we create will call try_to_freeze()
at an opportune time so that memory suspend can proceed. For the io-wq
worker threads, mark them as PF_NOFREEZE. They could potentially be
blocked for a long time.
Reported-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca> Tested-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Mon, 1 Mar 2021 18:20:48 +0000 (18:20 +0000)]
io_uring: remove extra in_idle wake up
io_dismantle_req() is always followed by io_put_task(), which already do
proper in_idle wake ups, so we can skip waking the owner task in
io_dismantle_req(). The rules are simpler now, do io_put_task() shortly
after ending a request, and it will be fine.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Mon, 1 Mar 2021 18:20:45 +0000 (18:20 +0000)]
io_uring: choose right tctx->io_wq for try cancel
When we cancel SQPOLL, @task in io_uring_try_cancel_requests() will
differ from current. Use the right tctx from passed in @task, and don't
forget that it can be NULL when the io_uring ctx exits.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Mon, 1 Mar 2021 20:56:00 +0000 (13:56 -0700)]
io_uring: fix -EAGAIN retry with IOPOLL
We no longer revert the iovec on -EIOCBQUEUED, see commit a2677e9ea0c3,
and this started causing issues for IOPOLL on devies that run out of
request slots. Turns out what outside of needing a revert for those, we
also had a bug where we didn't properly setup retry inside the submission
path. That could cause re-import of the iovec, if any, and that could lead
to spurious results if the application had those allocated on the stack.
Catch -EAGAIN retry and make the iovec stable for IOPOLL, just like we do
for !IOPOLL retries.
Pavel Begunkov [Mon, 1 Mar 2021 13:02:15 +0000 (13:02 +0000)]
io_uring: kill sqo_dead and sqo submission halting
As SQPOLL task doesn't poke into ->sqo_task anymore, there is no need to
kill the sqo when the master task exits. Before it was necessary to
avoid races accessing sqo_task->files with removing them.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
[axboe: don't forget to enable SQPOLL before exit, if started disabled] Signed-off-by: Jens Axboe <axboe@kernel.dk>
which is due to the driver doing poll_wait() twice on the same
wait_queue_head. That is perfectly valid, but from checking the rest
of the kernel tree, it's the only driver that does this.
We can handle this just fine, we just need to ignore the second addition
as we'll get woken just fine on the first one.
Jens Axboe [Sun, 28 Feb 2021 22:32:18 +0000 (15:32 -0700)]
io_uring: ensure that SQPOLL thread is started for exit
If we create it in a disabled state because IORING_SETUP_R_DISABLED is
set on ring creation, we need to ensure that we've kicked the thread if
we're exiting before it's been explicitly disabled. Otherwise we can run
into a deadlock where exit is waiting go park the SQPOLL thread, but the
SQPOLL thread itself is waiting to get a signal to start.
That results in the below trace of both tasks hung, waiting on each other:
Pavel Begunkov [Sun, 28 Feb 2021 22:04:53 +0000 (22:04 +0000)]
io_uring: fix __tctx_task_work() ctx race
There is an unlikely but possible race using a freed context. That's
because req->task_work.func() can free a request, but we won't
necessarily find a completion in submit_state.comp and so all ctx refs
may be put by the time we do mutex_lock(&ctx->uring_ctx);
There are several reasons why it can miss going through
submit_state.comp: 1) req->task_work.func() didn't complete it itself,
but punted to iowq (e.g. reissue) and it got freed later, or a similar
situation with it overflowing and getting flushed by someone else, or
being submitted to IRQ completion, 2) As we don't hold the uring_lock,
someone else can do io_submit_flush_completions() and put our ref.
3) Bugs and code obscurities, e.g. failing to propagate issue_flags
properly.
One example is as follows
CPU1 | CPU2
=======================================================================
@req->task_work.func() |
-> @req overflwed, |
so submit_state.comp,nr==0 |
| flush overflows, and free @req
| ctx refs == 0, free it
ctx is dead, but we do |
lock + flush + unlock |
So take a ctx reference for each new ctx we see in __tctx_task_work(),
and do release it until we do all our flushing.
Fixes: 1a12bfc276c9 ("io_uring: enable req cache for task_work items") Reported-by: syzbot+a157ac7c03a56397f553@syzkaller.appspotmail.com Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
[axboe: fold in my one-liner and fix ref mismatch] Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Sat, 27 Feb 2021 22:57:30 +0000 (15:57 -0700)]
io_uring: move cred assignment into io_issue_sqe()
If we move it in there, then we no longer have to care about it in io-wq.
This means we can drop the cred handling in io-wq, and we can drop the
REQ_F_WORK_INITIALIZED flag and async init functions as that was the last
user of it since we moved to the new workers. Then we can also drop
io_wq_work->creds, and just hold the personality u16 in there instead.
Suggested-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Sat, 27 Feb 2021 11:16:46 +0000 (11:16 +0000)]
io_uring: destroy io-wq on exec
Destroy current's io-wq backend and tctx on __io_uring_task_cancel(),
aka exec(). Looks it's not strictly necessary, because it will be done
at some point when the task dies and changes of creds/files/etc. are
handled, but better to do that earlier to free io-wq and not potentially
lock previous mm and other resources for the time being.
It's safe to do because we wait for all requests of the current task to
complete, so no request will use tctx afterwards. Note, that
io_uring_files_cancel() may leave some requests for later reaping, so it
leaves tctx intact, that's ok as the task is dying anyway.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Feb 2021 21:54:16 +0000 (14:54 -0700)]
io_uring: fix race condition in task_work add and clear
We clear the bit marking the ctx task_work as active after having run
the queued work, but we really should be clearing it before. Otherwise
we can hit a tiny race ala:
CPU0 CPU1
io_task_work_add() tctx_task_work()
run_work
add_to_list
test_and_set_bit
clear_bit
already set
and CPU0 will return thinking the task_work is queued, while in reality
it's already being run. If we hit the condition after __tctx_task_work()
found no more work, but before we've cleared the bit, then we'll end up
thinking it's queued and will be run. In reality it is queued, but we
didn't queue the ctx task_work to ensure that it gets run.
Fixes: dbe654152584 ("io_uring: provide FIFO ordering for task_work") Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Feb 2021 20:48:19 +0000 (13:48 -0700)]
io-wq: provide an io_wq_put_and_exit() helper
If we put the io-wq from io_uring, we really want it to exit. Provide
a helper that does that for us. Couple that with not having the manager
hold a reference to the 'wq' and the normal SQPOLL exit will tear down
the io-wq context appropriate.
On the io-wq side, our wq context is per task, so only the task itself
is manipulating ->manager and hence it's safe to check and clear without
any extra locking. We just need to ensure that the manager task stays
around, in case it exits.
Jens Axboe [Fri, 26 Feb 2021 20:46:49 +0000 (13:46 -0700)]
io_uring: don't use complete_all() on SQPOLL thread exit
We want to reuse this completion, and a single complete should do just
fine. Ensure that we park ourselves first if requested, as that is what
lead to the initial deadlock in this area. If we've got someone attempting
to park us, then we can't proceed without having them finish first.
Pavel Begunkov [Fri, 26 Feb 2021 15:47:56 +0000 (15:47 +0000)]
io_uring: run fallback on cancellation
io_uring_try_cancel_requests() matches not only current's requests, but
also of other exiting tasks, so we need to actively cancel them and not
just wait, especially since the function can be called on flush during
do_exit() -> exit_files().
Even if it's not a problem for now, it's much nicer to know that the
function tries to cancel everything it can.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 26 Feb 2021 18:27:15 +0000 (11:27 -0700)]
io_uring: SQPOLL stop error handling fixes
If we fail to fork an SQPOLL worker, we can hit cancel, and hence
attempted thread stop, with the thread already being stopped. Ensure
we check for that.
Also guard thread stop fully by the sqd mutex, just like we do for
park.
Jens Axboe [Fri, 26 Feb 2021 16:56:32 +0000 (09:56 -0700)]
io-wq: wait for manager exit on wq destroy
The manager waits for the workers, hence the manager is always valid if
workers are running. Now also have wq destroy wait for the manager on
exit, so we now everything is gone.
Jens Axboe [Fri, 26 Feb 2021 16:47:20 +0000 (09:47 -0700)]
io-wq: have manager wait for all workers to exit
Instead of having to wait separately on workers and manager, just have
the manager wait on the workers. We use an atomic_t for the reference
here, as we need to start at 0 and allow increment from that. Since the
number of workers is naturally capped by the allowed nr of processes,
and that uses an int, there is no risk of overflow.
Zenghui Yu [Sat, 27 Feb 2021 07:39:09 +0000 (15:39 +0800)]
iommu/vt-d: Fix status code for Allocate/Free PASID command
As per Intel vt-d spec, Rev 3.0 (section 10.4.45 "Virtual Command Response
Register"), the status code of "No PASID available" error in response to
the Allocate PASID command is 2, not 1. The same for "Invalid PASID" error
in response to the Free PASID command.
We will otherwise see confusing kernel log under the command failure from
guest side. Fix it.
Lu Baolu [Thu, 25 Feb 2021 06:14:54 +0000 (14:14 +0800)]
iommu: Don't use lazy flush for untrusted device
The lazy IOTLB flushing setup leaves a time window, in which the device
can still access some system memory, which has already been unmapped by
the device driver. It's not suitable for untrusted devices. A malicious
device might use this to attack the system by obtaining data that it
shouldn't obtain.
Nicolin Chen [Thu, 18 Feb 2021 22:07:02 +0000 (14:07 -0800)]
iommu/tegra-smmu: Fix mc errors on tegra124-nyan
Commit 1863ef332929 ("iommu/tegra-smmu: Rework tegra_smmu_probe_device()")
removed certain hack in the tegra_smmu_probe() by relying on IOMMU core to
of_xlate SMMU's SID per device, so as to get rid of tegra_smmu_find() and
tegra_smmu_configure() that are typically done in the IOMMU core also.
This approach works for both existing devices that have DT nodes and other
devices (like PCI device) that don't exist in DT, on Tegra210 and Tegra3
upon testing. However, Page Fault errors are reported on tegra124-Nyan:
After debugging, I found that the mentioned commit changed some function
callback sequence of tegra-smmu's, resulting in enabling SMMU for display
client before display driver gets initialized. I couldn't reproduce exact
same issue on Tegra210 as Tegra124 (arm-32) differs at arch-level code.
Actually this Page Fault is a known issue, as on most of Tegra platforms,
display gets enabled by the bootloader for the splash screen feature, so
it keeps filling the framebuffer memory. A proper fix to this issue is to
1:1 linear map the framebuffer memory to IOVA space so the SMMU will have
the same address as the physical address in its page table. Yet, Thierry
has been working on the solution above for a year, and it hasn't merged.
Therefore, let's partially revert the mentioned commit to fix the errors.
The reason why we do a partial revert here is that we can still set priv
in ->of_xlate() callback for PCI devices. Meanwhile, devices existing in
DT, like display, will go through tegra_smmu_configure() at the stage of
bus_set_iommu() when SMMU gets probed(), as what it did before we merged
the mentioned commit.
Once we have the linear map solution for framebuffer memory, this change
can be cleaned away.
[Big thank to Guillaume who reported and helped debugging/verification]
Andrey Ryabinin [Wed, 17 Feb 2021 14:30:04 +0000 (17:30 +0300)]
iommu/amd: Fix sleeping in atomic in increase_address_space()
increase_address_space() calls get_zeroed_page(gfp) under spin_lock with
disabled interrupts. gfp flags passed to increase_address_space() may allow
sleeping, so it comes to this:
BUG: sleeping function called from invalid context at mm/page_alloc.c:4342
in_atomic(): 1, irqs_disabled(): 1, pid: 21555, name: epdcbbf1qnhbsd8
Kevin Wang [Tue, 2 Mar 2021 07:54:00 +0000 (15:54 +0800)]
drm/amdgpu: fix parameter error of RREG32_PCIE() in amdgpu_regs_pcie
the register offset isn't needed division by 4 to pass RREG32_PCIE()
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Colin Ian King [Tue, 2 Mar 2021 14:05:09 +0000 (14:05 +0000)]
drm/amd/display: fix the return of the uninitialized value in ret
Currently if stream->signal is neither SIGNAL_TYPE_DISPLAY_PORT_MST or
SIGNAL_TYPE_DISPLAY_PORT then variable ret is uninitialized and this is
checked for > 0 at the end of the function. Ret should be initialized,
I believe setting it to zero is a correct default.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 7c894119f1ee ("drm/amd/display: Add return code instead of boolean for future use") Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Mon, 1 Mar 2021 15:42:50 +0000 (10:42 -0500)]
drm/amdgpu: enable BACO runpm by default on sienna cichlid and navy flounder
It works fine and was only disabled because primary GPUs
don't enter runpm if there is a console bound to the fbdev due
to the kmap. This will at least allow runpm on secondary cards.
Reviewed-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 24 Feb 2021 20:46:59 +0000 (15:46 -0500)]
drm/amdgpu/swsmu/vangogh: Only use RLCPowerNotify msg for disable
Per discussions with PMFW team, the driver only needs to
notify the PMFW when the RLC is disabled. The RLC FW will notify
the PMFW directly when it's enabled.
Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 24 Feb 2021 17:21:07 +0000 (12:21 -0500)]
drm/amdgpu/pm: make unsupported power profile messages debug
Making them an error confuses users and the errors are harmless
as not all asics support all profiles.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1488 Acked-by: Nirmoy Das <nirmoy.das@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / kernel.git / log