sh: add AT_HWCAP flag for J-Core cas.l instruction
The J-Core cpu has, as an ISA extension, an atomic compare-and-swap
instruction cas.l which applications need to use (instead the imask or
gusa atomic models, which are fundamentally limited to UP) for
synchronization in order to be compatible with SMP systems. Provide a
hwcap flag so that it's possible to do runtime selection and support
both.
Rich Felker [Thu, 17 Mar 2016 23:09:37 +0000 (23:09 +0000)]
sh: add support for J-Core J2 processor
At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.
Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.
No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.
Rich Felker [Wed, 1 Jun 2016 22:21:45 +0000 (22:21 +0000)]
sh: fix build regression with CONFIG_OF && !CONFIG_OF_FLATTREE
Such a configuration could only be selected by manually selecting
CONFIG_OF; SH_DEVICE_TREE selects both. The affected code is using the
flat DTB at boot time and thus rightfully should depend on
OF_FLATTREE, not just OF.
Rich Felker [Thu, 26 May 2016 22:18:52 +0000 (22:18 +0000)]
sh: allow clocksource drivers to register sched_clock backends
There is no arch-specific sched_clock implementation for sh, resulting
in use of the old default jiffies-based implementation. Instead, use
the modern generic sched_clock framework so that drivers can register
better backends.
Paul Gortmaker [Fri, 22 Apr 2016 18:07:04 +0000 (14:07 -0400)]
sh: make heartbeat driver explicitly non-modular
The Kconfig for this driver is currently:
config HEARTBEAT
bool "Heartbeat LED"
....meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Cc: linux-sh@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Rich Felker <dalias@libc.org>
The futex cmpxchg runtime testing in kernel/futex.c depends on
accesses to address 0 producing EFAULT, which obviously does not work
on nommu. Since SH always has cmpxchg, disable the broken runtime
detection.
At some point this should be fixed at the kernel/futex.c level. UP
machines can always provide a working cmpxchg with interrupt masking,
and SMP cannot function without a working cmpxchg anyway.
Rich Felker [Tue, 22 Mar 2016 22:02:23 +0000 (22:02 +0000)]
sh: disable aliased page logic on NOMMU models
SH3/4 (with MMU) have a virtually indexed cache, requiring explicit
work to avoid consistency problems arising from having the same
physical address range cached in multiple cache lines. This is
unneeded for the NOMMU case, and some of the resulting code paths
(kmap_coherent) don't work. SH2 only avoided this problem by having a
4-way associative cache with way size equal to the page size (4k),
yielding no cache index bits outside of the page offset and thus no
aliases.
sh: make sigcontext definition consistent across fpu/nofpu models
Up until now, the SH version of the sigcontext structure, and thus
mcontext_t/ucontext_t, varied depending on the cpu model the kernel
was built to run on. SH-4 (including SH-4A) and SH-2A used the form
with space for FPU registers, and everything else used a form that
omitted them.
From a userspace perspective, however, the structure layout must be
fixed for a given ABI. Traditionally glibc and uClibc used the form
with space for FPU registers only when __SH4__ (which implies FPU;
__SH4_NOFPU__ is the predefined macro for SH-4 but with no-FPU ABI)
was defined. As a result:
- SH-4 no-FPU programs never matched kernel sigcontext.
- SH-3 programs did not match kernel sigcontext if run on SH-4,
despite an apparent intent that they be compatible.
- SH-2 and SH-2A programs (using uClibc) did not match kernel
sigcontext if run on SH-2A.
The mismatch might seem inconsequential because it occurs at the end
of the sigcontext structure, but sigcontext is embedded as uc_mcontext
in ucontext_t, where it is followed by uc_sigmask, an important member
for signal handlers to have access to. In particular, access to
uc_sigmask is necessary for a correct implementation of thread
cancellation.
It would be possible to retain support for both sigcontext ABIs via a
personality mechanism, but since many configurations were already
broken and nobody noticed, and since there are very few if any users
of legacy no-FPU models anymore, I have opted to just remove the
variation and always include space for the FPU registers in
sigcontext. This was proposed and discussed on a thread "SH sigcontext
ABI is broken" cross-posted to linux-sh, libc-alpha, and musl libc
lists in June 2015, and no objections were raised.
Pan Xinhui [Wed, 20 Apr 2016 06:41:00 +0000 (14:41 +0800)]
sh: cmpxchg: fix a bit shift bug in big_endian os
Correct bitoff in big endian OS.
Current code works correctly for 1 byte but not for 2 bytes.
Fixes: 3226aad81aa6 ("sh: support 1 and 2 byte xchg") Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Rich Felker <dalias@libc.org>
- more aggressive caching when we can rely on close-to-open
cache consistency
- remove serialisation of O_DIRECT reads and writes
- optimise several code paths to not flush to disk unnecessarily.
However allow for the idiosyncracies of pNFS for those layout
types that need to issue a LAYOUTCOMMIT before the metadata can
be updated on the server.
- SUNRPC updates to the client data receive path
- pNFS/SCSI support RH/Fedora dm-mpath device nodes
- pNFS files/flexfiles can now use unprivileged ports when
the generic NFS mount options allow it.
Bugfixes:
- Don't use RDMA direct data placement together with data
integrity or privacy security flavours
- Remove the RDMA ALLPHYSICAL memory registration mode as
it has potential security holes.
- Several layout recall fixes to improve NFSv4.1 protocol
compliance.
- Fix an Oops in the pNFS files and flexfiles connection
setup to the DS
- Allow retry of operations that used a returned delegation
stateid
- Don't mark the inode as revalidated if a LAYOUTCOMMIT is
outstanding
- Fix writeback races in nfs4_copy_range() and
nfs42_proc_deallocate()"
* tag 'nfs-for-4.8-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (104 commits)
pNFS: Actively set attributes as invalid if LAYOUTCOMMIT is outstanding
NFSv4: Clean up lookup of SECINFO_NO_NAME
NFSv4.2: Fix warning "variable ‘stateids’ set but not used"
NFSv4: Fix warning "no previous prototype for ‘nfs4_listxattr’"
SUNRPC: Fix a compiler warning in fs/nfs/clnt.c
pNFS: Remove redundant smp_mb() from pnfs_init_lseg()
pNFS: Cleanup - do layout segment initialisation in one place
pNFS: Remove redundant stateid invalidation
pNFS: Remove redundant pnfs_mark_layout_returned_if_empty()
pNFS: Clear the layout metadata if the server changed the layout stateid
pNFS: Cleanup - don't open code pnfs_mark_layout_stateid_invalid()
NFS: pnfs_mark_matching_lsegs_return() should match the layout sequence id
pNFS: Do not set plh_return_seq for non-callback related layoutreturns
pNFS: Ensure layoutreturn acts as a completion for layout callbacks
pNFS: Fix CB_LAYOUTRECALL stateid verification
pNFS: Always update the layout barrier seqid on LAYOUTGET
pNFS: Always update the layout stateid if NFS_LAYOUT_INVALID_STID is set
pNFS: Clear the layout return tracking on layout reinitialisation
pNFS: LAYOUTRETURN should only update the stateid if the layout is valid
nfs: don't create zero-length requests
...
Merge branch 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode updates from Thomas Gleixner:
- more work to make the microcode loader robust
- a fix for the micro code load precedence
- fixes for initrd loading with randomized memory
- less printk noise on SMP machines
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm, x86/microcode: Add __PAGE_OFFSET_BASE define on 32-bit
x86/microcode/intel: Fix initrd loading with CONFIG_RANDOMIZE_MEMORY=y
x86/microcode: Remove unused symbol exports
x86/microcode/intel: Do not issue microcode updates messages on each CPU
Documentation/microcode: Document some aspects for more clarity
x86/microcode/AMD: Make amd_ucode_patch[] static
x86/microcode/intel: Unexport save_mc_for_early()
x86/microcode/intel: Rename load_microcode_early() to find_microcode_patch()
x86/microcode: Propagate save_microcode_in_initrd() retval
x86/microcode: Get rid of find_cpio_data()'s dummy offset arg
lib/cpio: Make find_cpio_data()'s offset arg optional
x86/microcode: Fix suspend to RAM with builtin microcode
x86/microcode: Fix loading precedence
Merge branch 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpufeature updates from Thomas Gleixner:
- a workaround for the MONITOR instruction erratum of Goldmont CPUs
- small fixes and cleanups here and there
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add workaround for MONITOR instruction erratum on Goldmont based CPUs
x86/cpu: Rename "WESTMERE2" family to "NEHALEM_G"
x86/amd_nb: Clean up init path
x86/cpufeature: Add helper macro for mask check macros
x86/cpufeature: Make sure DISABLED/REQUIRED macros are updated
x86/cpufeature: Update cpufeaure macros
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"This update contains:
- a fix for the bpf tools to use the new EM_BPF code
- a fix for the module parser of perf to retrieve the
proper text start address
- add str_error_c to libapi to avoid linking against
tools/lib/str_error_r.o"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib api: Add str_error_c to libapi
perf s390: Fix 'start' address of module's map
tools lib bpf: Use official ELF e_machine value
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc fixes from Thomas Gleixner:
"This update contains:
- a fix for stomp-machine so the nmi_watchdog wont trigger on the cpu
waiting for the others to execute the callback
- various fixes and updates to objtool including an resync of the
instruction decoder to match the kernel's decoder"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Un-capitalize "Warning" for out-of-sync instruction decoder
objtool: Resync x86 instruction decoder with the kernel's
objtool: Support new GCC 6 switch jump table pattern
stop_machine: Touch_nmi_watchdog() after MULTI_STOP_PREPARE
objtool: Add 'fixdep' to objtool/.gitignore
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Merge tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The bulk of the changes are updates and fixes to existing clk provider
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
- removed CLK_IS_ROOT flag
New clk provider drivers:
- Renesas r8a7796 clock pulse generator / module standby and
software reset
- Allwinner sun8i H3 clock controller unit
- AmLogic meson8b clock controller (rewritten)
- AmLogic gxbb clock controller
- support for some new ICs was added by simple changes to static
data tables for chips sharing the same family
Driver updates of note:
- the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with
the DT ABI"
* tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: Makefile: re-sort and clean up
Revert "clk: gxbb: expose CLKID_MMC_PCLK"
clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver
clk: samsung: make clk-s5pv210-audss explicitly non-modular
clk: exynos5433: remove CLK_IGNORE_UNUSED flag from SPI clocks
clk: oxnas: Add hardware dependencies
clk: imx7d: do not set parent of ethernet time/ref clocks
ARM: dt: sun8i: switch the H3 to the new CCU driver
clk: sunxi-ng: h3: Fix Kconfig symbol typo
clk: sunxi-ng: h3: Fix audio clock divider offset
clk: sunxi-ng: Add H3 clocks
clk: sunxi-ng: Add N-K-M-P factor clock
clk: sunxi-ng: Add N-K-M Factor clock
clk: sunxi-ng: Add N-M-factor clock support
clk: sunxi-ng: Add N-K-factor clock support
clk: sunxi-ng: Add M-P factor clock support
clk: sunxi-ng: Add divider
clk: sunxi-ng: Add phase clock support
clk: sunxi-ng: Add mux clock support
clk: sunxi-ng: Add gate clock support
...
Merge branch 'stable-4.8' of git://git.infradead.org/users/pcmoore/audit
Pull audit updates from Paul Moore:
"Six audit patches for 4.8.
There are a couple of style and minor whitespace tweaks for the logs,
as well as a minor fixup to catch errors on user filter rules, however
the major improvements are a fix to the s390 syscall argument masking
code (reviewed by the nice s390 folks), some consolidation around the
exclude filtering (less code, always a win), and a double-fetch fix
for recording the execve arguments"
* 'stable-4.8' of git://git.infradead.org/users/pcmoore/audit:
audit: fix a double fetch in audit_log_single_execve_arg()
audit: fix whitespace in CWD record
audit: add fields to exclude filter by reusing user filter
s390: ensure that syscall arguments are properly masked on s390
audit: fix some horrible switch statement style crimes
audit: fixup: log on errors from filter user rules
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull userns vfs updates from Eric Biederman:
"This tree contains some very long awaited work on generalizing the
user namespace support for mounting filesystems to include filesystems
with a backing store. The real world target is fuse but the goal is
to update the vfs to allow any filesystem to be supported. This
patchset is based on a lot of code review and testing to approach that
goal.
While looking at what is needed to support the fuse filesystem it
became clear that there were things like xattrs for security modules
that needed special treatment. That the resolution of those concerns
would not be fuse specific. That sorting out these general issues
made most sense at the generic level, where the right people could be
drawn into the conversation, and the issues could be solved for
everyone.
At a high level what this patchset does a couple of simple things:
- Add a user namespace owner (s_user_ns) to struct super_block.
- Teach the vfs to handle filesystem uids and gids not mapping into
to kuids and kgids and being reported as INVALID_UID and
INVALID_GID in vfs data structures.
By assigning a user namespace owner filesystems that are mounted with
only user namespace privilege can be detected. This allows security
modules and the like to know which mounts may not be trusted. This
also allows the set of uids and gids that are communicated to the
filesystem to be capped at the set of kuids and kgids that are in the
owning user namespace of the filesystem.
One of the crazier corner casees this handles is the case of inodes
whose i_uid or i_gid are not mapped into the vfs. Most of the code
simply doesn't care but it is easy to confuse the inode writeback path
so no operation that could cause an inode write-back is permitted for
such inodes (aka only reads are allowed).
This set of changes starts out by cleaning up the code paths involved
in user namespace permirted mounts. Then when things are clean enough
adds code that cleanly sets s_user_ns. Then additional restrictions
are added that are possible now that the filesystem superblock
contains owner information.
These changes should not affect anyone in practice, but there are some
parts of these restrictions that are changes in behavior.
- Andy's restriction on suid executables that does not honor the
suid bit when the path is from another mount namespace (think
/proc/[pid]/fd/) or when the filesystem was mounted by a less
privileged user.
- The replacement of the user namespace implicit setting of MNT_NODEV
with implicitly setting SB_I_NODEV on the filesystem superblock
instead.
Using SB_I_NODEV is a stronger form that happens to make this state
user invisible. The user visibility can be managed but it caused
problems when it was introduced from applications reasonably
expecting mount flags to be what they were set to.
There is a little bit of work remaining before it is safe to support
mounting filesystems with backing store in user namespaces, beyond
what is in this set of changes.
- Verifying the mounter has permission to read/write the block device
during mount.
- Teaching the integrity modules IMA and EVM to handle filesystems
mounted with only user namespace root and to reduce trust in their
security xattrs accordingly.
- Capturing the mounters credentials and using that for permission
checks in d_automount and the like. (Given that overlayfs already
does this, and we need the work in d_automount it make sense to
generalize this case).
Furthermore there are a few changes that are on the wishlist:
- Get all filesystems supporting posix acls using the generic posix
acls so that posix_acl_fix_xattr_from_user and
posix_acl_fix_xattr_to_user may be removed. [Maintainability]
- Reducing the permission checks in places such as remount to allow
the superblock owner to perform them.
- Allowing the superblock owner to chown files with unmapped uids and
gids to something that is mapped so the files may be treated
normally.
I am not considering even obvious relaxations of permission checks
until it is clear there are no more corner cases that need to be
locked down and handled generically.
Many thanks to Seth Forshee who kept this code alive, and putting up
with me rewriting substantial portions of what he did to handle more
corner cases, and for his diligent testing and reviewing of my
changes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (30 commits)
fs: Call d_automount with the filesystems creds
fs: Update i_[ug]id_(read|write) to translate relative to s_user_ns
evm: Translate user/group ids relative to s_user_ns when computing HMAC
dquot: For now explicitly don't support filesystems outside of init_user_ns
quota: Handle quota data stored in s_user_ns in quota_setxquota
quota: Ensure qids map to the filesystem
vfs: Don't create inodes with a uid or gid unknown to the vfs
vfs: Don't modify inodes with a uid or gid unknown to the vfs
cred: Reject inodes with invalid ids in set_create_file_as()
fs: Check for invalid i_uid in may_follow_link()
vfs: Verify acls are valid within superblock's s_user_ns.
userns: Handle -1 in k[ug]id_has_mapping when !CONFIG_USER_NS
fs: Refuse uid/gid changes which don't map into s_user_ns
selinux: Add support for unprivileged mounts from user namespaces
Smack: Handle labels consistently in untrusted mounts
Smack: Add support for unprivileged mounts from user namespaces
fs: Treat foreign mounts as nosuid
fs: Limit file caps to the user namespace of the super block
userns: Remove the now unnecessary FS_USERNS_DEV_MOUNT flag
userns: Remove implicit MNT_NODEV fragility.
...
Steve Twiss [Mon, 25 Jul 2016 15:20:54 +0000 (16:20 +0100)]
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
Buck and LDO binding name changes.
The binding names for the regulators have been changed to match the current
expectation from existing device tree source files.
This fix rectifies the disparity between what currently exists in some
.dts[i] board files and what is listed in this binding document. This
change re-aligns those differences and also brings the binding document
in-line with the expectations of the product datasheet from Dialog
Semiconductor.
Bucks and LDOs now follow the expected notation:
{ buck1, buck2, buck3, buck4 }
{ ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10 }
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Rob Herring <robh@kernel.org>
Merge tag 'pm-urgent-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a nasty (and really hard to debug) memory corruption during resume
from hibernation on x86-64 (that leads to a kernel panic most of the
time) due to the use of a stale stack pointer value in FRAME_BEGIN
(Josh Poimboeuf)"
* tag 'pm-urgent-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Fix hibernation return address corruption
Merge branch 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull more cgroup updates from Tejun Heo:
"I forgot to include the patches which got applied to for-4.7-fixes
late during last cycle.
Eric's three patches fix bugs introduced with the namespace support"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroupns: Only allow creation of hierarchies in the initial cgroup namespace
cgroupns: Close race between cgroup_post_fork and copy_cgroup_ns
cgroupns: Fix the locking in copy_cgroup_ns
Merge branch 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
1) Double spin lock bug in sunhv serial driver, from Dan Carpenter.
2) Use correct RSS estimate when determining whether to grow the huge
TSB or not, from Mike Kravetz.
3) Don't use full three level page tables for hugepages, PMD level is
sufficient. From Nitin Gupta.
4) Mask out extraneous bits from TSB_TAG_ACCESS register, we only want
the address bits.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Trim page tables for 8M hugepages
sparc64 mm: Fix base TSB sizing when hugetlb pages are used
sparc: serial: sunhv: fix a double lock bug
sparc32: off by ones in BUG_ON()
sparc: Don't leak context bits into thread->fault_address
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: off by one in at32_init_pio()
avr32: fixup code style in unistd.h and syscall_table.S
avr32: wire up preadv2 and pwritev2 syscalls
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse updates from Miklos Szeredi:
"This fixes error propagation from writeback to fsync/close for
writeback cache mode as well as adding a missing capability flag to
the INIT message. The rest are cleanups.
(The commits are recent but all the code actually sat in -next for a
while now. The recommits are due to conflict avoidance and the
addition of Cc: stable@...)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: use filemap_check_errors()
mm: export filemap_check_errors() to modules
fuse: fix wrong assignment of ->flags in fuse_send_init()
fuse: fuse_flush must check mapping->flags for errors
fuse: fsync() did not return IO errors
fuse: don't mess with blocking signals
new helper: wait_event_killable_exclusive()
fuse: improve aio directIO write performance for size extending writes
As Miklos points out in commit c1b2cc1a765a, the "lookup_hash()" helper
is now unused, and in fact, with the hash salting changes, since the
hash of a dentry name now depends on the directory dentry it is in, the
helper function isn't even really likely to be useful.
So rather than keep it around in case somebody else might end up finding
a use for it, let's just remove the helper and not trick people into
thinking it might be a useful thing.
For example, I had obviously completely missed how the helper didn't
follow the normal dentry hashing patterns, and how the hash salting
patch broke overlayfs. Things would quietly build and look sane, but
not work.
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs update from Miklos Szeredi:
"First of all, this fixes a regression in overlayfs introduced by the
dentry hash salting. I've moved the patch fixing this to the front of
the queue, so if (god forbid) something needs to be bisected in
overlayfs this regression won't interfere with that.
The biggest part is preparation for selinux support, done by Vivek
Goyal. Essentially this makes all operations on underlying
filesystems be done with credentials of mounter. This makes
everything nicely consistent.
There are also fixes for a number of known and recently discovered
non-standard behavior (thanks to Eryu Guan for testing and improving
the test suites)"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (23 commits)
ovl: simplify empty checking
qstr: constify instances in overlayfs
ovl: clear nlink on rmdir
ovl: disallow overlayfs as upperdir
ovl: fix warning
ovl: remove duplicated include from super.c
ovl: append MAY_READ when diluting write checks
ovl: dilute permission checks on lower only if not special file
ovl: fix POSIX ACL setting
ovl: share inode for hard link
ovl: store real inode pointer in ->i_private
ovl: permission: return ECHILD instead of ENOENT
ovl: update atime on upper
ovl: fix sgid on directory
ovl: simplify permission checking
ovl: do not require mounter to have MAY_WRITE on lower
ovl: do operations on underlying file system in mounter's context
ovl: modify ovl_permission() to do checks on two inodes
ovl: define ->get_acl() for overlay inodes
ovl: move some common code in a function
...
Merge tag 'freevxfs-for-4.8' of git://git.infradead.org/users/hch/freevxfs
Pull freevxfs updates from Christoph Hellwig:
"Support for foreign endianess and HP-UP superblocks from
Krzysztof Błaszkowski"
* tag 'freevxfs-for-4.8' of git://git.infradead.org/users/hch/freevxfs:
freevxfs: update Kconfig information
freevxfs: refactor readdir and lookup code
freevxfs: fix lack of inode initialization
freevxfs: fix memory leak in vxfs_read_fshead()
freevxfs: update documentation and cresdits for HP-UX support
freevxfs: implement ->alloc_inode and ->destroy_inode
freevxfs: avoid the need for forward declaring the super operations
freevxfs: move VFS inode allocation into vxfs_blkiget and vxfs_stiget
freevxfs: remove vxfs_put_fake_inode
freevxfs: handle big endian HP-UX file systems
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS/SMB3 fixes from Steve French:
"Various CIFS/SMB3 fixes, most for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix a possible invalid memory access in smb2_query_symlink()
fs/cifs: make share unaccessible at root level mountable
cifs: fix crash due to race in hmac(md5) handling
cifs: unbreak TCP session reuse
cifs: Check for existing directory when opening file with O_CREAT
Add MF-Symlinks support for SMB 2.0
For PMD aligned (8M) hugepages, we currently allocate
all four page table levels which is wasteful. We now
allocate till PMD level only which saves memory usage
from page tables.
Also, when freeing page table for 8M hugepage backed region,
make sure we don't try to access non-existent PTE level.
objtool: Un-capitalize "Warning" for out-of-sync instruction decoder
Change "Warning" to "warning" to make it look more like a GCC warning.
Hopefully that will be enough to help the 0-day bot or other automated
tools catch this warning earlier before it ends up in Linus's tree.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/b1669f391a5db91040427fd9f8e1e79db18f9709.1469751119.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
objtool: Resync x86 instruction decoder with the kernel's
This fixes the following warning:
Warning: objtool: x86 instruction decoder differs from kernel
Unfortunately we have three identical copies of the x86 instruction
decoder in the kernel tree that have to be manually kept in sync.
It's on my TODO list to at least library-ize the ones in the tools
subdir so we'd only have two of them instead of three. In the meantime,
here's another manual sync.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: c61f4d5ebaf0 ("perf tools: Add AVX-512 support to the instruction decoder used by Intel PT") Link: http://lkml.kernel.org/r/d7f74b4d91fed25b0be33cd5c86f5131fa1a7529.1469751119.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
objtool: Support new GCC 6 switch jump table pattern
This fixes some false positive objtool warnings seen with gcc 6.1.1:
kernel/trace/ring_buffer.o: warning: objtool: ring_buffer_read_page()+0x36c: sibling call from callable instruction with changed frame pointer
arch/x86/kernel/reboot.o: warning: objtool: native_machine_emergency_restart()+0x139: sibling call from callable instruction with changed frame pointer
lib/xz/xz_dec_stream.o: warning: objtool: xz_dec_run()+0xc2: sibling call from callable instruction with changed frame pointer
With GCC 6, a new code pattern is sometimes used to access a switch
statement jump table in .rodata, which objtool doesn't yet recognize:
mov [rodata addr],%reg1
... some instructions ...
jmpq *(%reg1,%reg2,8)
Add support for detecting that pattern. The detection code is rather
crude, but it's still effective at weeding out false positives and
catching real warnings. It can be refined later once objtool starts
reading DWARF CFI.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/b8c9503b4ad8c8a827cc5400db4c1b40a3ea07bc.1469751119.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'perf-urgent-for-mingo-20160728' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fix from Arnaldo Carvalho de Melo:
- Fix the tools/vm/ build by making libapi provide the str_error_c function,
that libapi uses but wasn't part of the list of objects linked with
tools/vm/ programs. (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
fuse: fuse_flush must check mapping->flags for errors
fuse_flush() calls write_inode_now() that triggers writeback, but actual
writeback will happen later, on fuse_sync_writes(). If an error happens,
fuse_writepage_end() will set error bit in mapping->flags. So, we have to
check mapping->flags after fuse_sync_writes().
In kernel bug 150021, a kernel panic was reported when restoring a
hibernate image. Only a picture of the oops was reported, so I can't
paste the whole thing here. But here are the most interesting parts:
The RIP is on the same page as RBP, so it apparently started executing
on the stack.
The bug was bisected to commit ef0f3ed5a4ac (x86/asm/power: Create
stack frames in hibernate_asm_64.S), which in retrospect seems quite
dangerous, since that code saves and restores the stack pointer from a
global variable ('saved_context').
There are a lot of moving parts in the hibernate save and restore paths,
so I don't know exactly what caused the panic. Presumably, a FRAME_END
was executed without the corresponding FRAME_BEGIN, or vice versa. That
would corrupt the return address on the stack and would be consistent
with the details of the above panic.
[ rjw: One major problem is that by the time the FRAME_BEGIN in
restore_registers() is executed, the stack pointer value may not
be valid any more. Namely, the stack area pointed to by it
previously may have been overwritten by some image memory contents
and that page frame may now be used for whatever different purpose
it had been allocated for before hibernation. In that case, the
FRAME_BEGIN will corrupt that memory. ]
Instead of doing the frame pointer save/restore around the bounds of the
affected functions, just do it around the call to swsusp_save().
That has the same effect of ensuring that if swsusp_save() sleeps, the
frame pointers will be correct. It's also a much more obviously safe
way to do it than the original patch. And objtool still doesn't report
any warnings.
Fixes: ef0f3ed5a4ac (x86/asm/power: Create stack frames in hibernate_asm_64.S) Link: https://bugzilla.kernel.org/show_bug.cgi?id=150021 Cc: 4.6+ <stable@vger.kernel.org> # 4.6+ Reported-by: Andre Reinke <andre.reinke@mailbox.org> Tested-by: Andre Reinke <andre.reinke@mailbox.org> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The empty checking logic is duplicated in ovl_check_empty_and_clear() and
ovl_remove_and_whiteout(), except the condition for clearing whiteouts is
different:
ovl_check_empty_and_clear() checked for being upper
ovl_remove_and_whiteout() checked for merge OR lower
Move the intersection of those checks (upper AND merge) into
ovl_check_empty_and_clear() and simplify ovl_remove_and_whiteout().
Right now we remove MAY_WRITE/MAY_APPEND bits from mask if realfile is on
lower/. This is done as files on lower will never be written and will be
copied up. But to copy up a file, mounter should have MAY_READ permission
otherwise copy up will fail. So set MAY_READ in mask when MAY_WRITE is
reset.
Dan Walsh noticed this when he did access(lowerfile, W_OK) and it returned
True (context mounts) but when he tried to actually write to file, it
failed as mounter did not have permission on lower file.
[SzM] don't set MAY_READ if only MAY_APPEND is set without MAY_WRITE; this
won't trigger a copy-up.
ovl: dilute permission checks on lower only if not special file
Right now if file is on lower/, we remove MAY_WRITE/MAY_APPEND bits from
mask as lower/ will never be written and file will be copied up. But this
is not true for special files. These files are not copied up and are opened
in place. So don't dilute the checks for these types of files.
1) Some permission checks are done by ->setxattr() which now uses mounter's
creds ("ovl: do operations on underlying file system in mounter's
context"). These permission checks need to be done with current cred as
well.
2) Setting ACL can fail for various reasons. We do not need to copy up in
these cases.
In the mean time switch to using generic_setxattr.
[Arnd Bergmann] Fix link error without POSIX ACL. posix_acl_from_xattr()
doesn't have a 'static inline' implementation when CONFIG_FS_POSIX_ACL is
disabled, and I could not come up with an obvious way to do it.
This instead avoids the link error by defining two sets of ACL operations
and letting the compiler drop one of the two at compile time depending
on CONFIG_FS_POSIX_ACL. This avoids all references to the ACL code,
also leading to smaller code.
Inode attributes are copied up to overlay inode (uid, gid, mode, atime,
mtime, ctime) so generic code using these fields works correcty. If a hard
link is created in overlayfs separate inodes are allocated for each link.
If chmod/chown/etc. is performed on one of the links then the inode
belonging to the other ones won't be updated.
This patch attempts to fix this by sharing inodes for hard links.
Use inode hash (with real inode pointer as a key) to make sure overlay
inodes are shared for hard links on upper. Hard links on lower are still
split (which is not user observable until the copy-up happens, see
Documentation/filesystems/overlayfs.txt under "Non-standard behavior").
The inode is only inserted in the hash if it is non-directoy and upper.
To get from overlay inode to real inode we currently use 'struct
ovl_entry', which has lifetime connected to overlay dentry. This is okay,
since each overlay dentry had a new overlay inode allocated.
Following patch will break that assumption, so need to leave out ovl_entry.
This patch stores the real inode directly in i_private, with the lowest bit
used to indicate whether the inode is upper or lower.
Lifetime rules remain, using ovl_inode_real() must only be done while
caller holds ref on overlay dentry (and hence on real dentry), or within
RCU protected regions.
This patch adds an i_op->update_time() handler to overlayfs inodes. This
forwards atime updates to the upper layer only. No atime updates are done
on lower layers.
Remove implicit atime updates to underlying files and directories with
O_NOATIME. Remove explicit atime update in ovl_readlink().
Clear atime related mnt flags from cloned upper mount. This means atime
updates are controlled purely by overlayfs mount options.
Reported-by: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
When creating directory in workdir, the group/sgid inheritance from the
parent dir was omitted completely. Fix this by calling inode_init_owner()
on overlay inode and using the resulting uid/gid/mode to create the file.
Unfortunately the sgid bit can be stripped off due to umask, so need to
reset the mode in this case in workdir before moving the directory in
place.
The fact that we always do permission checking on the overlay inode and
clear MAY_WRITE for checking access to the lower inode allows cruft to be
removed from ovl_permission().
1) "default_permissions" option effectively did generic_permission() on the
overlay inode with i_mode, i_uid and i_gid updated from underlying
filesystem. This is what we do by default now. It did the update using
vfs_getattr() but that's only needed if the underlying filesystem can
change (which is not allowed). We may later introduce a "paranoia_mode"
that verifies that mode/uid/gid are not changed.
2) splitting out the IS_RDONLY() check from inode_permission() also becomes
unnecessary once we remove the MAY_WRITE from the lower inode check.
ovl: do not require mounter to have MAY_WRITE on lower
Now we have two levels of checks in ovl_permission(). overlay inode
is checked with the creds of task while underlying inode is checked
with the creds of mounter.
Looks like mounter does not have to have WRITE access to files on lower/.
So remove the MAY_WRITE from access mask for checks on underlying
lower inode.
This means task should still have the MAY_WRITE permission on lower
inode and mounter is not required to have MAY_WRITE.
It also solves the problem of read only NFS mounts being used as lower.
If __inode_permission(lower_inode, MAY_WRITE) is called on read only
NFS, it fails. By resetting MAY_WRITE, check succeeds and case of
read only NFS shold work with overlay without having to specify any
special mount options (default permission).
ovl: do operations on underlying file system in mounter's context
Given we are now doing checks both on overlay inode as well underlying
inode, we should be able to do checks and operations on underlying file
system using mounter's context.
So modify all operations to do checks/operations on underlying dentry/inode
in the context of mounter.
ovl: modify ovl_permission() to do checks on two inodes
Right now ovl_permission() calls __inode_permission(realinode), to do
permission checks on real inode and no checks are done on overlay inode.
Modify it to do checks both on overlay inode as well as underlying inode.
Checks on overlay inode will be done with the creds of calling task while
checks on underlying inode will be done with the creds of mounter.
Now we are planning to do DAC permission checks on overlay inode
itself. And to make it work, we will need to make sure we can get acls from
underlying inode. So define ->get_acl() for overlay inodes and this in turn
calls into underlying filesystem to get acls, if any.
Vivek Goyal [Thu, 16 Jun 2016 14:09:14 +0000 (10:09 -0400)]
ovl: move some common code in a function
ovl_create_upper() and ovl_create_over_whiteout() seem to be sharing some
common code which can be moved into a separate function. No functionality
change.
The hash salting changes meant that we can no longer reuse the hash in the
overlay dentry to look up the underlying dentry.
Instead of lookup_hash(), use lookup_one_len_unlocked() and swith to
mounter's creds (like we do for all other operations later in the series).
Now the lookup_hash() export introduced in 4.6 by 3c9fe8cdff1b ("vfs: add
lookup_hash() helper") is unused and can possibly be removed; its
usefulness negated by the hash salting and the idea that mounter's creds
should be used on operations on underlying filesystems.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Fixes: 8387ff2577eb ("vfs: make the string hashes salt the hash")
avr32: fixup code style in unistd.h and syscall_table.S
This patch swaps the mix of tabs and space for alignment of comment
after code to use spaces only.
Also document why recvmmsg was defined twice in the syscall_table.S
table, but only once in unistd.h. In short, wired in the table by
generic arch patch, but forgotten in unistd.h (review slip).
This patch wires up the new preadv2 and pwritev2 syscall on AVR32.
On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.
Mike Kravetz [Fri, 15 Jul 2016 20:08:42 +0000 (13:08 -0700)]
sparc64 mm: Fix base TSB sizing when hugetlb pages are used
do_sparc64_fault() calculates both the base and huge page RSS sizes and
uses this information in calls to tsb_grow(). The calculation for base
page TSB size is not correct if the task uses hugetlb pages. hugetlb
pages are not accounted for in RSS, therefore the call to get_mm_rss(mm)
does not include hugetlb pages. However, the number of pages based on
huge_pte_count (which does include hugetlb pages) is subtracted from
this value. This will result in an artificially small and often negative
RSS calculation. The base TSB size is then often set to max_tsb_size
as the passed RSS is unsigned, so a negative value looks really big.
THP pages are also accounted for in huge_pte_count, and THP pages are
accounted for in RSS so the calculation in do_sparc64_fault() is correct
if a task only uses THP pages.
A single huge_pte_count is not sufficient for TSB sizing if both hugetlb
and THP pages can be used. Instead of a single counter, use two: one
for hugetlb and one for THP.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'trace-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This is mostly clean ups and small fixes. Some of the more visible
changes are:
- The function pid code uses the event pid filtering logic
- [ku]probe events have access to current->comm
- trace_printk now has sample code
- PCI devices now trace physical addresses
- stack tracing has less unnessary functions traced"
* tag 'trace-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
printk, tracing: Avoiding unneeded blank lines
tracing: Use __get_str() when manipulating strings
tracing, RAS: Cleanup on __get_str() usage
tracing: Use outer () on __get_str() definition
ftrace: Reduce size of function graph entries
tracing: Have HIST_TRIGGERS select TRACING
tracing: Using for_each_set_bit() to simplify trace_pid_write()
ftrace: Move toplevel init out of ftrace_init_tracefs()
tracing/function_graph: Fix filters for function_graph threshold
tracing: Skip more functions when doing stack tracing of events
tracing: Expose CPU physical addresses (resource values) for PCI devices
tracing: Show the preempt count of when the event was called
tracing: Add trace_printk sample code
tracing: Choose static tp_printk buffer by explicit nesting count
tracing: expose current->comm to [ku]probe events
ftrace: Have set_ftrace_pid use the bitmap like events do
tracing: Move pid_list write processing into its own function
tracing: Move the pid_list seq_file functions to be global
tracing: Move filtered_pid helper functions into trace.c
tracing: Make the pid filtering helper functions global
Merge tag 'vfio-v4.8-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Enable no-iommu mode for platform devices (Peng Fan)
- Sub-page mmap for exclusive pages (Yongji Xie)
- Use-after-free fix (Ilya Lesokhin)
- Support for ACPI-based platform devices (Sinan Kaya)
* tag 'vfio-v4.8-rc1' of git://github.com/awilliam/linux-vfio:
vfio: platform: check reset call return code during release
vfio: platform: check reset call return code during open
vfio, platform: make reset driver a requirement by default
vfio: platform: call _RST method when using ACPI
vfio: platform: add extra debug info argument to call reset
vfio: platform: add support for ACPI probe
vfio: platform: determine reset capability
vfio: platform: move reset call to a common function
vfio: platform: rename reset function
vfio: fix possible use after free of vfio group
vfio-pci: Allow to mmap sub-page MMIO BARs if the mmio page is exclusive
vfio: platform: support No-IOMMU mode
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD updates from Shaohua Li:
- A bunch of patches from Neil Brown to fix RCU usage
- Two performance improvement patches from Tomasz Majchrzak
- Alexey Obitotskiy fixes module refcount issue
- Arnd Bergmann fixes time granularity
- Cong Wang fixes a list corruption issue
- Guoqing Jiang fixes a deadlock in md-cluster
- A null pointer deference fix from me
- Song Liu fixes misuse of raid6 rmw
- Other trival/cleanup fixes from Guoqing Jiang and Xiao Ni
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (28 commits)
MD: fix null pointer deference
raid10: improve random reads performance
md: add missing sysfs_notify on array_state update
Fix kernel module refcount handling
md: use seconds granularity for error logging
md: reduce the number of synchronize_rcu() calls when multiple devices fail.
md: be extra careful not to take a reference to a Faulty device.
md/multipath: add rcu protection to rdev access in multipath_status.
md/raid5: add rcu protection to rdev accesses in raid5_status.
md/raid5: add rcu protection to rdev accesses in want_replace
md/raid5: add rcu protection to rdev accesses in handle_failed_sync.
md/raid1: add rcu protection to rdev in fix_read_error
md/raid1: small code cleanup in end_sync_write
md/raid1: small cleanup in raid1_end_read/write_request
md/raid10: simplify print_conf a little.
md/raid10: minor code improvement in fix_read_error()
md/raid10: add rcu protection to rdev access during reshape.
md/raid10: add rcu protection to rdev access in raid10_sync_request.
md/raid10: add rcu protection in raid10_status.
md/raid10: fix refounct imbalance when resyncing an array with a replacement device.
...
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
Merge more updates from Andrew Morton:
"The rest of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (101 commits)
mm, compaction: simplify contended compaction handling
mm, compaction: introduce direct compaction priority
mm, thp: remove __GFP_NORETRY from khugepaged and madvised allocations
mm, page_alloc: make THP-specific decisions more generic
mm, page_alloc: restructure direct compaction handling in slowpath
mm, page_alloc: don't retry initial attempt in slowpath
mm, page_alloc: set alloc_flags only once in slowpath
lib/stackdepot.c: use __GFP_NOWARN for stack allocations
mm, kasan: switch SLUB to stackdepot, enable memory quarantine for SLUB
mm, kasan: account for object redzone in SLUB's nearest_obj()
mm: fix use-after-free if memory allocation failed in vma_adjust()
zsmalloc: Delete an unnecessary check before the function call "iput"
mm/memblock.c: fix index adjustment error in __next_mem_range_rev()
mem-hotplug: alloc new page from a nearest neighbor node when mem-offline
mm: optimize copy_page_to/from_iter_iovec
mm: add cond_resched() to generic_swapfile_activate()
Revert "mm, mempool: only set __GFP_NOMEMALLOC if there are free elements"
mm, compaction: don't isolate PageWriteback pages in MIGRATE_SYNC_LIGHT mode
mm: hwpoison: remove incorrect comments
make __section_nr() more efficient
...
mm, compaction: simplify contended compaction handling
Async compaction detects contention either due to failing trylock on
zone->lock or lru_lock, or by need_resched(). Since 1f9efdef4f3f ("mm,
compaction: khugepaged should not give up due to need_resched()") the
code got quite complicated to distinguish these two up to the
__alloc_pages_slowpath() level, so different decisions could be taken
for khugepaged allocations.
After the recent changes, khugepaged allocations don't check for
contended compaction anymore, so we again don't need to distinguish lock
and sched contention, and simplify the current convoluted code a lot.
However, I believe it's also possible to simplify even more and
completely remove the check for contended compaction after the initial
async compaction for costly orders, which was originally aimed at THP
page fault allocations. There are several reasons why this can be done
now:
- with the new defaults, THP page faults no longer do reclaim/compaction at
all, unless the system admin has overridden the default, or application has
indicated via madvise that it can benefit from THP's. In both cases, it
means that the potential extra latency is expected and worth the benefits.
- even if reclaim/compaction proceeds after this patch where it previously
wouldn't, the second compaction attempt is still async and will detect the
contention and back off, if the contention persists
- there are still heuristics like deferred compaction and pageblock skip bits
in place that prevent excessive THP page fault latencies
mm, compaction: introduce direct compaction priority
In the context of direct compaction, for some types of allocations we
would like the compaction to either succeed or definitely fail while
trying as hard as possible. Current async/sync_light migration mode is
insufficient, as there are heuristics such as caching scanner positions,
marking pageblocks as unsuitable or deferring compaction for a zone. At
least the final compaction attempt should be able to override these
heuristics.
To communicate how hard compaction should try, we replace migration mode
with a new enum compact_priority and change the relevant function
signatures. In compact_zone_order() where struct compact_control is
constructed, the priority is mapped to suitable control flags. This
patch itself has no functional change, as the current priority levels
are mapped back to the same migration modes as before. Expanding them
will be done next.
Note that !CONFIG_COMPACTION variant of try_to_compact_pages() is
removed, as the only caller exists under CONFIG_COMPACTION.
mm, thp: remove __GFP_NORETRY from khugepaged and madvised allocations
After the previous patch, we can distinguish costly allocations that
should be really lightweight, such as THP page faults, with
__GFP_NORETRY. This means we don't need to recognize khugepaged
allocations via PF_KTHREAD anymore. We can also change THP page faults
in areas where madvise(MADV_HUGEPAGE) was used to try as hard as
khugepaged, as the process has indicated that it benefits from THP's and
is willing to pay some initial latency costs.
We can also make the flags handling less cryptic by distinguishing
GFP_TRANSHUGE_LIGHT (no reclaim at all, default mode in page fault) from
GFP_TRANSHUGE (only direct reclaim, khugepaged default). Adding
__GFP_NORETRY or __GFP_KSWAPD_RECLAIM is done where needed.
The patch effectively changes the current GFP_TRANSHUGE users as
follows:
* get_huge_zero_page() - the zero page lifetime should be relatively
long and it's shared by multiple users, so it's worth spending some
effort on it. We use GFP_TRANSHUGE, and __GFP_NORETRY is not added.
This also restores direct reclaim to this allocation, which was
unintentionally removed by commit e4a49efe4e7e ("mm: thp: set THP defrag
by default to madvise and add a stall-free defrag option")
* alloc_hugepage_khugepaged_gfpmask() - this is khugepaged, so latency
is not an issue. So if khugepaged "defrag" is enabled (the default), do
reclaim via GFP_TRANSHUGE without __GFP_NORETRY. We can remove the
PF_KTHREAD check from page alloc.
As a side-effect, khugepaged will now no longer check if the initial
compaction was deferred or contended. This is OK, as khugepaged sleep
times between collapsion attempts are long enough to prevent noticeable
disruption, so we should allow it to spend some effort.
* migrate_misplaced_transhuge_page() - already was masking out
__GFP_RECLAIM, so just convert to GFP_TRANSHUGE_LIGHT which is
equivalent.
* alloc_hugepage_direct_gfpmask() - vma's with VM_HUGEPAGE (via madvise)
are now allocating without __GFP_NORETRY. Other vma's keep using
__GFP_NORETRY if direct reclaim/compaction is at all allowed (by default
it's allowed only for madvised vma's). The rest is conversion to
GFP_TRANSHUGE(_LIGHT).
mm, page_alloc: make THP-specific decisions more generic
Since THP allocations during page faults can be costly, extra decisions
are employed for them to avoid excessive reclaim and compaction, if the
initial compaction doesn't look promising. The detection has never been
perfect as there is no gfp flag specific to THP allocations. At this
moment it checks the whole combination of flags that makes up
GFP_TRANSHUGE, and hopes that no other users of such combination exist,
or would mind being treated the same way. Extra care is also taken to
separate allocations from khugepaged, where latency doesn't matter that
much.
It is however possible to distinguish these allocations in a simpler and
more reliable way. The key observation is that after the initial
compaction followed by the first iteration of "standard"
reclaim/compaction, both __GFP_NORETRY allocations and costly
allocations without __GFP_REPEAT are declared as failures:
/* Do not loop if specifically requested */
if (gfp_mask & __GFP_NORETRY)
goto nopage;
/*
* Do not retry costly high order allocations unless they are
* __GFP_REPEAT
*/
if (order > PAGE_ALLOC_COSTLY_ORDER && !(gfp_mask & __GFP_REPEAT))
goto nopage;
This means we can further distinguish allocations that are costly order
*and* additionally include the __GFP_NORETRY flag. As it happens,
GFP_TRANSHUGE allocations do already fall into this category. This will
also allow other costly allocations with similar high-order benefit vs
latency considerations to use this semantic. Furthermore, we can
distinguish THP allocations that should try a bit harder (such as from
khugepageed) by removing __GFP_NORETRY, as will be done in the next
patch.
mm, page_alloc: restructure direct compaction handling in slowpath
The retry loop in __alloc_pages_slowpath is supposed to keep trying
reclaim and compaction (and OOM), until either the allocation succeeds,
or returns with failure. Success here is more probable when reclaim
precedes compaction, as certain watermarks have to be met for compaction
to even try, and more free pages increase the probability of compaction
success. On the other hand, starting with light async compaction (if
the watermarks allow it), can be more efficient, especially for smaller
orders, if there's enough free memory which is just fragmented.
Thus, the current code starts with compaction before reclaim, and to
make sure that the last reclaim is always followed by a final
compaction, there's another direct compaction call at the end of the
loop. This makes the code hard to follow and adds some duplicated
handling of migration_mode decisions. It's also somewhat inefficient
that even if reclaim or compaction decides not to retry, the final
compaction is still attempted. Some gfp flags combination also shortcut
these retry decisions by "goto noretry;", making it even harder to
follow.
This patch attempts to restructure the code with only minimal functional
changes. The call to the first compaction and THP-specific checks are
now placed above the retry loop, and the "noretry" direct compaction is
removed.
The initial compaction is additionally restricted only to costly orders,
as we can expect smaller orders to be held back by watermarks, and only
larger orders to suffer primarily from fragmentation. This better
matches the checks in reclaim's shrink_zones().
There are two other smaller functional changes. One is that the upgrade
from async migration to light sync migration will always occur after the
initial compaction. This is how it has been until recent patch "mm,
oom: protect !costly allocations some more", which introduced upgrading
the mode based on COMPACT_COMPLETE result, but kept the final compaction
always upgraded, which made it even more special. It's better to return
to the simpler handling for now, as migration modes will be further
modified later in the series.
The second change is that once both reclaim and compaction declare it's
not worth to retry the reclaim/compact loop, there is no final
compaction attempt. As argued above, this is intentional. If that
final compaction were to succeed, it would be due to a wrong retry
decision, or simply a race with somebody else freeing memory for us.
The main outcome of this patch should be simpler code. Logically, the
initial compaction without reclaim is the exceptional case to the
reclaim/compaction scheme, but prior to the patch, it was the last loop
iteration that was exceptional. Now the code matches the logic better.
The change also enable the following patches.
mm, page_alloc: don't retry initial attempt in slowpath
After __alloc_pages_slowpath() sets up new alloc_flags and wakes up
kswapd, it first tries get_page_from_freelist() with the new
alloc_flags, as it may succeed e.g. due to using min watermark instead
of low watermark. It makes sense to to do this attempt before adjusting
zonelist based on alloc_flags/gfp_mask, as it's still relatively a fast
path if we just wake up kswapd and successfully allocate.
This patch therefore moves the initial attempt above the retry label and
reorganizes a bit the part below the retry label. We still have to
attempt get_page_from_freelist() on each retry, as some allocations
cannot do that as part of direct reclaim or compaction, and yet are not
allowed to fail (even though they do a WARN_ON_ONCE() and thus should
not exist). We can reuse the call meant for ALLOC_NO_WATERMARKS attempt
and just set alloc_flags to ALLOC_NO_WATERMARKS if the context allows
it. As a side-effect, the attempts from direct reclaim/compaction will
also no longer obey watermarks once this is set, but there's little harm
in that.
Kswapd wakeups are also done on each retry to be safe from potential
races resulting in kswapd going to sleep while a process (that may not
be able to reclaim by itself) is still looping.
Link: http://lkml.kernel.org/r/20160721073614.24395-4-vbabka@suse.cz Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm, page_alloc: set alloc_flags only once in slowpath
In __alloc_pages_slowpath(), alloc_flags doesn't change after it's
initialized, so move the initialization above the retry: label. Also
make the comment above the initialization more descriptive.
The only exception in the alloc_flags being constant is
ALLOC_NO_WATERMARKS, which may change due to TIF_MEMDIE being set on the
allocating thread. We can fix this, and make the code simpler and a bit
more effective at the same time, by moving the part that determines
ALLOC_NO_WATERMARKS from gfp_to_alloc_flags() to gfp_pfmemalloc_allowed().
This means we don't have to mask out ALLOC_NO_WATERMARKS in numerous
places in __alloc_pages_slowpath() anymore. The only two tests for the
flag can instead call gfp_pfmemalloc_allowed().
Link: http://lkml.kernel.org/r/20160721073614.24395-3-vbabka@suse.cz Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm, kasan: switch SLUB to stackdepot, enable memory quarantine for SLUB
For KASAN builds:
- switch SLUB allocator to using stackdepot instead of storing the
allocation/deallocation stacks in the objects;
- change the freelist hook so that parts of the freelist can be put
into the quarantine.
mm, kasan: account for object redzone in SLUB's nearest_obj()
When looking up the nearest SLUB object for a given address, correctly
calculate its offset if SLAB_RED_ZONE is enabled for that cache.
Previously, when KASAN had detected an error on an object from a cache
with SLAB_RED_ZONE set, the actual start address of the object was
miscalculated, which led to random stacks having been reported.
When looking up the nearest SLUB object for a given address, correctly
calculate its offset if SLAB_RED_ZONE is enabled for that cache.
mm: fix use-after-free if memory allocation failed in vma_adjust()
There's one case when vma_adjust() expands the vma, overlapping with
*two* next vma. See case 6 of mprotect, described in the comment to
vma_merge().
To handle this (and only this) situation we iterate twice over main part
of the function. See "goto again".
Vegard reported[1] that he sees out-of-bounds access complain from
KASAN, if anon_vma_clone() on the *second* iteration fails.
This happens because we free 'next' vma by the end of first iteration
and don't have a way to undo this if anon_vma_clone() fails on the
second iteration.
The solution is to do all required allocations upfront, before we touch
vmas.
The allocation on the second iteration is only required if first two
vmas don't have anon_vma, but third does. So we need, in total, one
anon_vma_clone() call.
It's easy to adjust 'exporter' to the third vma for such case.
mem-hotplug: alloc new page from a nearest neighbor node when mem-offline
If we offline a node, alloc the new page from a nearest neighbor node
instead of the current node or other remote nodes, because re-migrate is
a waste of time and the distance of the remote nodes is often very
large.
Also use GFP_HIGHUSER_MOVABLE to alloc new page if the zone is movable
zone or highmem zone.
Link: http://lkml.kernel.org/r/5795E18B.5060302@huawei.com Signed-off-by: Xishi Qiu <qiuxishi@huawei.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
copy_page_to_iter_iovec() and copy_page_from_iter_iovec() copy some data
to userspace or from userspace. These functions have a fast path where
they map a page using kmap_atomic and a slow path where they use kmap.
kmap is slower than kmap_atomic, so the fast path is preferred.
However, on kernels without highmem support, kmap just calls
page_address, so there is no need to avoid kmap. On kernels without
highmem support, the fast path just increases code size (and cache
footprint) and it doesn't improve copy performance in any way.
This patch enables the fast path only if CONFIG_HIGHMEM is defined.
Code size reduced by this patch:
x86 (without highmem) 928
x86-64 960
sparc64 848
alpha 1136
pa-risc 1200
[akpm@linux-foundation.org: use IS_ENABLED(), per Andi] Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1607221711410.4818@file01.intranet.prod.int.rdu2.redhat.com Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Andi Kleen <andi@firstfloor.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / kernel.git / log