Enke Chen [Fri, 15 Jan 2021 22:30:58 +0000 (14:30 -0800)]
tcp: fix TCP_USER_TIMEOUT with zero window
The TCP session does not terminate with TCP_USER_TIMEOUT when data
remain untransmitted due to zero window.
The number of unanswered zero-window probes (tcp_probes_out) is
reset to zero with incoming acks irrespective of the window size,
as described in tcp_probe_timer():
RFC 1122 4.2.2.17 requires the sender to stay open indefinitely
as long as the receiver continues to respond probes. We support
this by default and reset icsk_probes_out with incoming ACKs.
This counter, however, is the wrong one to be used in calculating the
duration that the window remains closed and data remain untransmitted.
Thanks to Jonathan Maxwell <jmaxwell37@gmail.com> for diagnosing the
actual issue.
In this patch a new timestamp is introduced for the socket in order to
track the elapsed time for the zero-window probes that have not been
answered with any non-zero window ack.
Fixes: 8ef68003594b ("tcp: simplify window probe aborting on USER_TIMEOUT") Reported-by: William McCall <william.mccall@gmail.com> Co-developed-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Enke Chen <enchen@paloaltonetworks.com> Reviewed-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20210115223058.GA39267@localhost.localdomain Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matteo Croce [Fri, 15 Jan 2021 18:42:09 +0000 (19:42 +0100)]
ipv6: set multicast flag on the multicast route
The multicast route ff00::/8 is created with type RTN_UNICAST:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto kernel scope global metric 256 pref medium
Set the type to RTN_MULTICAST which is more appropriate.
Fixes: 80feebe50a45 ("net/ipv6: Save route type in rt6_info") Signed-off-by: Matteo Croce <mcroce@microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matteo Croce [Fri, 15 Jan 2021 18:42:08 +0000 (19:42 +0100)]
ipv6: create multicast route with RTPROT_KERNEL
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Jakub Kicinski [Mon, 18 Jan 2021 22:23:57 +0000 (14:23 -0800)]
Merge tag 'mac80211-for-net-2021-01-18.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes:
* kernel-doc parsing fixes
* incorrect debugfs string checks
* locking fix in regulatory
* some encryption-related fixes
* tag 'mac80211-for-net-2021-01-18.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211:
mac80211: check if atf has been disabled in __ieee80211_schedule_txq
mac80211: do not drop tx nulldata packets on encrypted links
mac80211: fix encryption key selection for 802.3 xmit
mac80211: fix fast-rx encryption check
mac80211: fix incorrect strlen of .write in debugfs
cfg80211: fix a kerneldoc markup
cfg80211: Save the regulatory domain with a lock
cfg80211/mac80211: fix kernel-doc for SAR APIs
====================
Rasmus Villemoes [Sat, 16 Jan 2021 02:39:35 +0000 (03:39 +0100)]
net: dsa: mv88e6xxx: also read STU state in mv88e6250_g1_vtu_getnext
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Vladimir Oltean [Mon, 18 Jan 2021 13:52:10 +0000 (15:52 +0200)]
net: mscc: ocelot: allow offloading of bridge on top of LAG
The blamed commit was too aggressive, and it made ocelot_netdevice_event
react only to network interface events emitted for the ocelot switch
ports.
In fact, only the PRECHANGEUPPER should have had that check.
When we ignore all events that are not for us, we miss the fact that the
upper of the LAG changes, and the bonding interface gets enslaved to a
bridge. This is an operation we could offload under certain conditions.
Fixes: 7f95f022c698 ("net: mscc: ocelot: don't handle netdev events for other netdevs") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20210118135210.2666246-1-olteanv@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skbuff: back tiny skbs with kmalloc() in __netdev_alloc_skb() too
Commit 2d3478de5a24 ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
1) Fix a double bpf_prog_put() for BPF_PROG_{TYPE_EXT,TYPE_TRACING} types in
link creation's error path causing a refcount underflow, from Jiri Olsa.
2) Fix BTF validation errors for the case where kernel modules don't declare
any new types and end up with an empty BTF, from Andrii Nakryiko.
3) Fix BPF local storage helpers to first check their {task,inode} owners for
being NULL before access, from KP Singh.
4) Fix a memory leak in BPF setsockopt handling for the case where optlen is
zero and thus temporary optval buffer should be freed, from Stanislav Fomichev.
5) Fix a syzbot memory allocation splat in BPF_PROG_TEST_RUN infra for
raw_tracepoint caused by too big ctx_size_in, from Song Liu.
6) Fix LLVM code generation issues with verifier where PTR_TO_MEM{,_OR_NULL}
registers were spilled to stack but not recognized, from Gilad Reti.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
MAINTAINERS: Update my email address
selftests/bpf: Add verifier test for PTR_TO_MEM spill
bpf: Support PTR_TO_MEM{,_OR_NULL} register spilling
bpf: Reject too big ctx_size_in for raw_tp test run
libbpf: Allow loading empty BTFs
bpf: Allow empty module BTFs
bpf: Don't leak memory in bpf getsockopt when optlen == 0
bpf: Update local storage test to check handling of null ptrs
bpf: Fix typo in bpf_inode_storage.c
bpf: Local storage helpers should check nullness of owner ptr passed
bpf: Prevent double bpf_prog_put call from bpf_tracing_prog_attach
====================
Cong Wang [Fri, 15 Jan 2021 18:50:24 +0000 (10:50 -0800)]
cls_flower: call nla_ok() before nla_next()
fl_set_enc_opt() simply checks if there are still bytes left to parse,
but this is not sufficent as syzbot seems to be able to generate
malformatted netlink messages. nla_ok() is more strict so should be
used to validate the next nlattr here.
And nla_validate_nested_deprecated() has less strict check too, it is
probably too late to switch to the strict version, but we can just
call nla_ok() too after it.
Reported-and-tested-by: syzbot+2624e3778b18fc497c92@syzkaller.appspotmail.com Fixes: 21fc99f378e0 ("net/sched: allow flower to match tunnel options") Fixes: 4af528bb493a ("net: sched: allow flower to match erspan options") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Xin Long <lucien.xin@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20210115185024.72298-1-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yingjie Wang [Fri, 15 Jan 2021 14:10:04 +0000 (06:10 -0800)]
octeontx2-af: Fix missing check bugs in rvu_cgx.c
In rvu_mbox_handler_cgx_mac_addr_get()
and rvu_mbox_handler_cgx_mac_addr_set(),
the msg is expected only from PFs that are mapped to CGX LMACs.
It should be checked before mapping,
so we add the is_cgx_config_permitted() in the functions.
Linus Torvalds [Thu, 14 Jan 2021 21:54:09 +0000 (13:54 -0800)]
Merge tag 'linux-kselftest-fixes-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"One single fix to skip BPF selftests by default.
BPF selftests have a hard dependency on cutting edge versions of tools
in the BPF ecosystem including LLVM.
Skipping BPF allows by default will make it easier for users
interested in running kselftest as a whole. Users can include BPF in
Kselftest build by via SKIP_TARGETS variable"
* tag 'linux-kselftest-fixes-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Skip BPF seftests by default
Linus Torvalds [Thu, 14 Jan 2021 21:31:07 +0000 (13:31 -0800)]
Merge tag 'net-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"We have a few fixes for long standing issues, in particular Eric's fix
to not underestimate the skb sizes, and my fix for brokenness of
register_netdevice() error path. They may uncover other bugs so we
will keep an eye on them. Also included are Willem's fixes for
kmap(_atomic).
Looking at the "current release" fixes, it seems we are about one rc
behind a normal cycle. We've previously seen an uptick of "people had
run their test suites" / "humans actually tried to use new features"
fixes between rc2 and rc3.
Summary:
Current release - regressions:
- fix feature enforcement to allow NETIF_F_HW_TLS_TX if IP_CSUM &&
IPV6_CSUM
- dcb: accept RTM_GETDCB messages carrying set-like DCB commands if
user is admin for backward-compatibility
- selftests/tls: fix selftests build after adding ChaCha20-Poly1305
Current release - always broken:
- ppp: fix refcount underflow on channel unbridge
- bnxt_en: clear DEFRAG flag in firmware message when retry flashing
- smc: fix out of bound access in the new netlink interface
Previous releases - regressions:
- fix use-after-free with UDP GRO by frags
- mptcp: better msk-level shutdown
- rndis_host: set proper input size for OID_GEN_PHYSICAL_MEDIUM
request
- avoid 32 x truesize under-estimation for tiny skbs
- fix issues around register_netdevice() failures
- udp: prevent reuseport_select_sock from reading uninitialized socks
- dsa: unbind all switches from tree when DSA master unbinds
- dsa: clear devlink port type before unregistering slave netdevs
- can: isotp: isotp_getname(): fix kernel information leak
- mlxsw: core: Thermal control fixes
- ipv6: validate GSO SKB against MTU before finish IPv6 processing
- stmmac: use __napi_schedule() for PREEMPT_RT
- net: mvpp2: remove Pause and Asym_Pause support
Misc:
- remove from MAINTAINERS folks who had been inactive for >5yrs"
* tag 'net-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
mptcp: fix locking in mptcp_disconnect()
net: Allow NETIF_F_HW_TLS_TX if IP_CSUM && IPV6_CSUM
MAINTAINERS: dccp: move Gerrit Renker to CREDITS
MAINTAINERS: ipvs: move Wensong Zhang to CREDITS
MAINTAINERS: tls: move Aviad to CREDITS
MAINTAINERS: ena: remove Zorik Machulsky from reviewers
MAINTAINERS: vrf: move Shrijeet to CREDITS
MAINTAINERS: net: move Alexey Kuznetsov to CREDITS
MAINTAINERS: altx: move Jay Cliburn to CREDITS
net: avoid 32 x truesize under-estimation for tiny skbs
nt: usb: USB_RTL8153_ECM should not default to y
net: stmmac: fix taprio configuration when base_time is in the past
net: stmmac: fix taprio schedule configuration
net: tip: fix a couple kernel-doc markups
net: sit: unregister_netdevice on newlink's error path
net: stmmac: Fixed mtu channged by cache aligned
cxgb4/chtls: Fix tid stuck due to wrong update of qid
i40e: fix potential NULL pointer dereferencing
net: stmmac: use __napi_schedule() for PREEMPT_RT
can: mcp251xfd: mcp251xfd_handle_rxif_one(): fix wrong NULL pointer check
...
Lorenzo Bianconi [Sat, 26 Dec 2020 09:39:08 +0000 (10:39 +0100)]
mac80211: check if atf has been disabled in __ieee80211_schedule_txq
Check if atf has been disabled in __ieee80211_schedule_txq() in order to
avoid a given sta is always put to the beginning of the active_txqs list
and never moved to the end since deficit is not decremented in
ieee80211_sta_register_airtime()
Felix Fietkau [Fri, 18 Dec 2020 19:15:25 +0000 (20:15 +0100)]
mac80211: do not drop tx nulldata packets on encrypted links
ieee80211_tx_h_select_key drops any non-mgmt packets without a key when
encryption is used. This is wrong for nulldata packets that can't be
encrypted and are sent out for probing clients and indicating 4-address
mode.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> Fixes: b1b24c1ac4c4 ("mac80211: drop data frames without key on encrypted links") Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20201218191525.1168-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Shayne Chen [Tue, 12 Jan 2021 03:20:28 +0000 (11:20 +0800)]
mac80211: fix incorrect strlen of .write in debugfs
This fixes strlen mismatch problems happening in some .write callbacks
of debugfs.
When trying to configure airtime_flags in debugfs, an error appeared:
ash: write error: Invalid argument
The error is returned from kstrtou16() since a wrong length makes it
miss the real end of input string. To fix this, use count as the string
length, and set proper end of string for a char buffer.
The debug print is shown - airtime_flags_write: count = 2, len = 8,
where the actual length is 2, but "len = strlen(buf)" gets 8.
Also cleanup the other similar cases for the sake of consistency.
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Link: https://lore.kernel.org/r/20210112032028.7482-1-shayne.chen@mediatek.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A function has a different name between their prototype
and its kernel-doc markup:
../include/net/cfg80211.h:1766: warning: expecting prototype for struct cfg80211_sar_chan_ranges. Prototype was for struct cfg80211_sar_freq_ranges instead
Linus Torvalds [Thu, 14 Jan 2021 19:10:12 +0000 (11:10 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- memory leak fix for Wacom driver (Ping Cheng)
- various trivial small fixes, cleanups and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: Add product ID for MX Ergo in Bluetooth mode
HID: Ignore battery for Elan touchscreen on ASUS UX550
HID: logitech-dj: add the G602 receiver
HID: wiimote: remove h from printk format specifier
HID: uclogic: remove h from printk format specifier
HID: sony: select CONFIG_CRC32
HID: sfh: fix address space confusion
HID: multitouch: Enable multi-input for Synaptics pointstick/touchpad device
HID: wacom: Fix memory leakage caused by kfifo_alloc
Tariq Toukan [Thu, 14 Jan 2021 15:12:15 +0000 (17:12 +0200)]
net: Allow NETIF_F_HW_TLS_TX if IP_CSUM && IPV6_CSUM
Cited patch below blocked the TLS TX device offload unless HW_CSUM
is set. This broke devices that use IP_CSUM && IP6_CSUM.
Here we fix it.
Note that the single HW_TLS_TX feature flag indicates support for
both IPv4/6, hence it should still be disabled in case only one of
(IP_CSUM | IPV6_CSUM) is set.
Fixes: f86d20e62630 ("net: Disable NETIF_F_HW_TLS_TX when HW_CSUM is disabled") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reported-by: Rohit Maheshwari <rohitm@chelsio.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Link: https://lore.kernel.org/r/20210114151215.7061-1-tariqt@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To make maintainers' lives easier we're trying to nudge people
towards CCing all the relevant folks on patches, in an attempt
to improve review rate. We have a check in patchwork which validates
the CC list against get_maintainers.pl. It's a little awkward, however,
to force people to CC maintainers who we haven't seen on the mailing
list for years. This series removes from maintainers folks who didn't
provide any tag (incl. authoring a patch) in the last 5 years.
To ensure reasonable signal to noise ratio we only considered
MAINTAINERS entries which had more than 100 patches fall under
them in that time period.
All this is purely a process-greasing exercise, I hope nobody
sees this series as an affront. Most folks are moved to CREDITS,
a couple entries are simply removed.
The following inactive maintainers are kept, because they indicated
the intention to come back in the near future:
- Veaceslav Falico (bonding)
- Christian Benvenuti (Cisco drivers)
- Felix Fietkau (mtk-eth)
- Mirko Linder (skge/sky2)
Patches in this series contain report from a script which did
the analysis. Big thanks to Jonathan Corbet for help and writing
the script (although I feel like I used it differently than Jon
may have intended ;)). The output format is thus:
Subsystem $name
Changes $reviewed / $total ($percent%) // how many changes to the subsystem had at least one ack/review
Last activity: $date_of_most_recent_patch
$maintainer/reviewer1:
Author $last_commit_authored_by_the_person $how_many_in_5yrs
Committer $last_committed $how_many
Tags $last_tag_like_review_signoff_etc $how_many
$maintainer/reviewer2:
Author $last_commit_authored_by_the_person $how_many_in_5yrs
Committer $last_committed $how_many
Tags $last_tag_like_review_signoff_etc $how_many
Top reviewers: // Top 3 reviewers (who are not listed in MAINTAINERS)
[$count_of_reviews_and_acks]: $email
INACTIVE MAINTAINER $name // maintainer / reviewer who has done nothing in last 5yrs
Jakub Kicinski [Thu, 14 Jan 2021 01:49:12 +0000 (17:49 -0800)]
MAINTAINERS: dccp: move Gerrit Renker to CREDITS
As far as I can tell we haven't heard from Gerrit for roughly
5 years now. DCCP patch would really benefit from some review.
Gerrit was the last maintainer so mark this entry as orphaned.
Jakub Kicinski [Thu, 14 Jan 2021 01:49:09 +0000 (17:49 -0800)]
MAINTAINERS: ena: remove Zorik Machulsky from reviewers
While ENA has 3 reviewers and 2 maintainers, we mostly see review
tags and comments from the maintainers. While we very much appreciate
Zorik's invovment in the community let's trim the reviewer list
down to folks we've seen tags from.
Eric Dumazet [Wed, 13 Jan 2021 16:18:19 +0000 (08:18 -0800)]
net: avoid 32 x truesize under-estimation for tiny skbs
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: e9908d59fe6c ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Greg Thelen <gthelen@google.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yannick Vignon [Wed, 13 Jan 2021 13:15:57 +0000 (14:15 +0100)]
net: stmmac: fix taprio configuration when base_time is in the past
The Synopsys TSN MAC supports Qbv base times in the past, but only up to a
certain limit. As a result, a taprio qdisc configuration with a small
base time (for example when treating the base time as a simple phase
offset) is not applied by the hardware and silently ignored.
This was observed on an NXP i.MX8MPlus device, but likely affects all
TSN-variants of the MAC.
Fix the issue by making sure the base time is in the future, pushing it by
an integer amount of cycle times if needed. (a similar check is already
done in several other taprio implementations, see for example
drivers/net/ethernet/intel/igc/igc_tsn.c#L116 or
drivers/net/dsa/sja1105/sja1105_ptp.h#L39).
Yannick Vignon [Wed, 13 Jan 2021 13:15:56 +0000 (14:15 +0100)]
net: stmmac: fix taprio schedule configuration
When configuring a 802.1Qbv schedule through the tc taprio qdisc on an NXP
i.MX8MPlus device, the effective cycle time differed from the requested one
by N*96ns, with N number of entries in the Qbv Gate Control List. This is
because the driver was adding a 96ns margin to each interval of the GCL,
apparently to account for the IPG. The problem was observed on NXP
i.MX8MPlus devices but likely affected all devices relying on the same
configuration callback (dwmac 4.00, 4.10, 5.10 variants).
Fix the issue by removing the margins, and simply setup the MAC with the
provided cycle time value. This is the behavior expected by the user-space
API, as altering the Qbv schedule timings would break standards conformance.
This is also the behavior of several other Ethernet MAC implementations
supporting taprio, including the dwxgmac variant of stmmac.
A function has a different name between their prototype
and its kernel-doc markup:
../net/tipc/link.c:2551: warning: expecting prototype for link_reset_stats(). Prototype was for tipc_link_reset_stats() instead
../net/tipc/node.c:1678: warning: expecting prototype for is the general link level function for message sending(). Prototype was for tipc_node_xmit() instead
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 14 Jan 2021 01:29:47 +0000 (17:29 -0800)]
net: sit: unregister_netdevice on newlink's error path
We need to unregister the netdevice if config failed.
.ndo_uninit takes care of most of the heavy lifting.
This was uncovered by recent commit 5a137c4f496a ("net: make
free_netdev() more lenient with unregistering devices").
Previously the partially-initialized device would be left
in the system.
Reported-and-tested-by: syzbot+2393580080a2da190f04@syzkaller.appspotmail.com Fixes: 405ae25df073 ("sit: allow to configure 6rd tunnels via netlink") Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20210114012947.2515313-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nicholas Miell [Mon, 11 Jan 2021 06:09:25 +0000 (22:09 -0800)]
HID: logitech-hidpp: Add product ID for MX Ergo in Bluetooth mode
The Logitech MX Ergo trackball supports HID++ 4.5 over Bluetooth. Add its
product ID to the table so we can get battery monitoring support.
(The hid-logitech-hidpp driver already recognizes it when connected via
a Unifying Receiver.)
[jkosina@suse.cz: fix whitespace damage] Signed-off-by: Nicholas Miell <nmiell@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
David Wu [Wed, 13 Jan 2021 03:41:09 +0000 (11:41 +0800)]
net: stmmac: Fixed mtu channged by cache aligned
Since the original mtu is not used when the mtu is updated,
the mtu is aligned with cache, this will get an incorrect.
For example, if you want to configure the mtu to be 1500,
but mtu 1536 is configured in fact.
Gilad Reti [Wed, 13 Jan 2021 05:38:08 +0000 (07:38 +0200)]
selftests/bpf: Add verifier test for PTR_TO_MEM spill
Add a test to check that the verifier is able to recognize spilling of
PTR_TO_MEM registers, by reserving a ringbuf buffer, forcing the spill
of a pointer holding the buffer address to the stack, filling it back
in from the stack and writing to the memory area pointed by it.
The patch was partially contributed by CyberArk Software, Inc.
Gilad Reti [Wed, 13 Jan 2021 05:38:07 +0000 (07:38 +0200)]
bpf: Support PTR_TO_MEM{,_OR_NULL} register spilling
Add support for pointer to mem register spilling, to allow the verifier
to track pointers to valid memory addresses. Such pointers are returned
for example by a successful call of the bpf_ringbuf_reserve helper.
The patch was partially contributed by CyberArk Software, Inc.
Fixes: 3360f04918f2 ("bpf: Implement BPF ring buffer and verifier support for it") Suggested-by: Yonghong Song <yhs@fb.com> Signed-off-by: Gilad Reti <gilad.reti@gmail.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: KP Singh <kpsingh@kernel.org> Link: https://lore.kernel.org/bpf/20210113053810.13518-1-gilad.reti@gmail.com
Ayush Sawal [Tue, 12 Jan 2021 05:36:00 +0000 (11:06 +0530)]
cxgb4/chtls: Fix tid stuck due to wrong update of qid
TID stuck is seen when there is a race in
CPL_PASS_ACCEPT_RPL/CPL_ABORT_REQ and abort is arriving
before the accept reply, which sets the queue number.
In this case HW ends up sending CPL_ABORT_RPL_RSS to an
incorrect ingress queue.
V1->V2:
- Removed the unused variable len in chtls_set_quiesce_ctrl().
V2->V3:
- As kfree_skb() has a check for null skb, so removed this
check before calling kfree_skb() in func chtls_send_reset().
Currently, the function i40e_construct_skb_zc only frees the input xdp
buffer when the output skb is successfully built. On error, the
function i40e_clean_rx_irq_zc does not commit anything for the current
packet descriptor and simply exits the packet descriptor processing
loop, with the plan to restart the processing of this descriptor on
the next invocation. Therefore, on error the ring next-to-clean
pointer should not advance, the xdp i.e. *bi buffer should not be
freed and the current buffer info should not be invalidated by setting
*bi to NULL. Therefore, the *bi should only be set to NULL when the
function i40e_construct_skb_zc is successful, otherwise a NULL *bi
will be dereferenced when the work for the current descriptor is
eventually restarted.
Fixes: 8afce9d352b1 ("i40e, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL") Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com> Acked-by: Björn Töpel <bjorn.topel@intel.com> Link: https://lore.kernel.org/r/20210111181138.49757-1-cristian.dumitrescu@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Seb Laveze [Tue, 12 Jan 2021 14:01:22 +0000 (15:01 +0100)]
net: stmmac: use __napi_schedule() for PREEMPT_RT
Use of __napi_schedule_irqoff() is not safe with PREEMPT_RT in which
hard interrupts are not disabled while running the threaded interrupt.
Using __napi_schedule() works for both PREEMPT_RT and mainline Linux,
just at the cost of an additional check if interrupts are disabled for
mainline (since they are already disabled).
Similar to the fix done for enetc commit 8881d455592d ("enetc: use
napi_schedule to be compatible with PREEMPT_RT")
If alloc_canfd_skb() returns NULL, 'cfg' is an uninitialized variable, so we
should check 'skb' rather than 'cfd' after calling alloc_canfd_skb(priv->ndev,
&cfd).
Oliver Hartkopp [Tue, 12 Jan 2021 09:16:43 +0000 (10:16 +0100)]
can: isotp: isotp_getname(): fix kernel information leak
Initialize the sockaddr_can structure to prevent a data leak to user space.
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Reported-by: syzbot+057884e2f453e8afebc8@syzkaller.appspotmail.com Fixes: 28da5a05c8c3 ("can: add ISO 15765-2:2016 transport protocol") Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20210112091643.11789-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Linus Torvalds [Wed, 13 Jan 2021 19:55:14 +0000 (11:55 -0800)]
Merge tag 'sound-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are some piled fixes, hopefully the last big one for 5.11.
All changes are device-specific small fixes, and majority of commits
are for ASoC while USB-audio got a bit large changes for addressing
the regression for devices with quirks"
* tag 'sound-5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
ALSA: hda/hdmi - enable runtime pm for CI AMD display audio
ALSA: firewire-tascam: Fix integer overflow in midi_port_work()
ALSA: fireface: Fix integer overflow in transmit_midi_msg()
ALSA: hda/tegra: fix tegra-hda on tegra30 soc
clk: tegra30: Add hda clock default rates to clock driver
ALSA: doc: Fix reference to mixart.rst
ALSA: usb-audio: Fix implicit feedback sync setup for Pioneer devices
ALSA: usb-audio: Annotate the endpoint index in audioformat
ALSA: usb-audio: Avoid unnecessary interface re-setup
ALSA: usb-audio: Choose audioformat of a counter-part substream
ALSA: usb-audio: Fix the missing endpoints creations for quirks
ALSA: hda/realtek: fix right sounds and mute/micmute LEDs for HP machines
ASoC: AMD Renoir - add DMI entry for Lenovo ThinkPad X395
ASoC: amd: Replacing MSI with Legacy IRQ model
ASoC: AMD Renoir - add DMI entry for Lenovo ThinkPad E14 Gen 2
ASoC: meson: axg-tdm-interface: fix loopback
ASoC: meson: axg-tdmin: fix axg skew offset
ASoC: max98373: don't access volatile registers in bias level off
ASoC: rt711: mutex between calibration and power state changes
ASoC: Intel: haswell: Add missing pm_ops
...
Baptiste Lepers [Tue, 12 Jan 2021 15:59:15 +0000 (15:59 +0000)]
rxrpc: Call state should be read with READ_ONCE() under some circumstances
The call state may be changed at any time by the data-ready routine in
response to received packets, so if the call state is to be read and acted
upon several times in a function, READ_ONCE() must be used unless the call
state lock is held.
As it happens, we used READ_ONCE() to read the state a few lines above the
unmarked read in rxrpc_input_data(), so use that value rather than
re-reading it.
David Howells [Tue, 12 Jan 2021 15:23:51 +0000 (15:23 +0000)]
rxrpc: Fix handling of an unsupported token type in rxrpc_read()
Clang static analysis reports the following:
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
====================
net/smc: fix out of bound access in netlink interface
Both patches fix possible out-of-bounds reads. The original code expected
that snprintf() reads len-1 bytes from source and appends the terminating
null, but actually snprintf() first copies len bytes and finally overwrites
the last byte with a null.
Fix this by using memcpy() and terminating the string afterwards.
====================
Guvenc Gulce [Tue, 12 Jan 2021 16:21:22 +0000 (17:21 +0100)]
net/smc: use memcpy instead of snprintf to avoid out of bounds read
Using snprintf() to convert not null-terminated strings to null
terminated strings may cause out of bounds read in the source string.
Therefore use memcpy() and terminate the target string with a null
afterwards.
Fixes: cc3a1695c6e2 ("net/smc: Add support for obtaining SMCR device list") Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 12 Jan 2021 16:21:21 +0000 (17:21 +0100)]
smc: fix out of bound access in smc_nl_get_sys_info()
smc_clc_get_hostname() sets the host pointer to a buffer
which is not NULL-terminated (see smc_clc_init()).
Reported-by: syzbot+f4708c391121cfc58396@syzkaller.appspotmail.com Fixes: e47932166c0e ("net/smc: Add support for obtaining system information") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Tue, 12 Jan 2021 17:25:24 +0000 (18:25 +0100)]
mptcp: better msk-level shutdown.
Instead of re-implementing most of inet_shutdown, re-use
such helper, and implement the MPTCP-specific bits at the
'proto' level.
The msk-level disconnect() can now be invoked, lets provide a
suitable implementation.
As a side effect, this fixes bad state management for listener
sockets. The latter could lead to division by 0 oops since
commit 22b32d260eb0 ("mptcp: refine MPTCP-level ack scheduling").
Fixes: 2e59714ed2c9 ("mptcp: Use full MPTCP-level disconnect state machine") Fixes: 22b32d260eb0 ("mptcp: refine MPTCP-level ack scheduling") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 13 Jan 2021 04:05:37 +0000 (20:05 -0800)]
Merge branch 'bnxt_en-bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
This series has 2 fixes. The first one fixes a resource accounting error
with the RDMA driver loaded and the second one fixes the firmware
flashing sequence after defragmentation.
====================
Pavan Chebbi [Mon, 11 Jan 2021 09:26:40 +0000 (04:26 -0500)]
bnxt_en: Clear DEFRAG flag in firmware message when retry flashing.
When the FW tells the driver to retry the INSTALL_UPDATE command after
it has cleared the NVM area, the driver is not clearing the previously
used ALLOWED_TO_DEFRAG flag. As a result the FW tries to defrag the NVM
area a second time in a loop and can fail the request.
Fixes: 1c8c94c78fea ("bnxt_en: Retry installing FW package under NO_SPACE error condition.") Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Mon, 11 Jan 2021 09:26:39 +0000 (04:26 -0500)]
bnxt_en: Improve stats context resource accounting with RDMA driver loaded.
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c786920deee3 ("bnxt_en: get rid of num_stat_ctxs variable") Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Schuermann [Mon, 11 Jan 2021 19:03:15 +0000 (20:03 +0100)]
r8153_ecm: Add Lenovo Powered USB-C Hub as a fallback of r8152
This commit enables the use of the r8153_ecm driver, introduced with
commit c34af2145635e3 ("net/usb/r8153_ecm: support ECM mode for
RTL8153") for the Lenovo Powered USB-C Hub (17ef:721e) based on the
Realtek RTL8153B chip.
This results in the following driver preference:
- if r8152 is available, use the r8152 driver
- if r8152 is not available, use the r8153_ecm driver
This is done to prevent the NIC from constantly sending pause frames
when the host system enters standby (fixed by using the r8152 driver
in "r8152: Add Lenovo Powered USB-C Travel Hub"), while still allowing
the device to work with the r8153_ecm driver as a fallback.
Leon Schuermann [Mon, 11 Jan 2021 19:03:13 +0000 (20:03 +0100)]
r8152: Add Lenovo Powered USB-C Travel Hub
This USB-C Hub (17ef:721e) based on the Realtek RTL8153B chip used to
use the cdc_ether driver. However, using this driver, with the system
suspended the device constantly sends pause-frames as soon as the
receive buffer fills up. This causes issues with other devices, where
some Ethernet switches stop forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
What happens is that devlink_port_unregister emits a netlink
DEVLINK_CMD_PORT_DEL message which associates the devlink port that is
getting unregistered with the ifindex of its corresponding net_device.
Only trouble is, the net_device has already been unregistered.
It looks like we can stub out the search for a corresponding net_device
if we clear the devlink_port's type. This looks like a bit of a hack,
but also seems to be the reason why the devlink_port_type_clear function
exists in the first place.
/* Notifier chain MUST detach us all upper devices. */
WARN_ON(netdev_has_any_upper_dev(dev));
Other stacked interfaces, like VLAN, do indeed listen for
NETDEV_UNREGISTER on the real_dev and also unregister themselves at that
time, which is clearly the behavior that rollback_registered_many
expects. But DSA interfaces are not VLAN. They have backing hardware
(platform devices, PCI devices, MDIO, SPI etc) which have a life cycle
of their own and we can't just trigger an unregister from the DSA
framework when we receive a netdev notifier that the master unregisters.
Luckily, there is something we can do, and that is to inform the driver
core that we have a runtime dependency to the DSA master interface's
device, and create a device link where that is the supplier and we are
the consumer. Having this device link will make the DSA switch unbind
before the DSA master unbinds, which is enough to avoid the WARN_ON from
rollback_registered_many.
Note that even before the blamed commit, DSA did nothing intelligent
when the master interface got unregistered either. See the discussion
here:
https://lore.kernel.org/netdev/20200505210253.20311-1-f.fainelli@gmail.com/
But this time, at least the WARN_ON is loud enough that the
upper_dev_link commit can be blamed.
The advantage with this approach vs dev_hold(master) in the attached
link is that the latter is not meant for long term reference counting.
With dev_hold, the only thing that will happen is that when the user
attempts an unbind of the DSA master, netdev_wait_allrefs will keep
waiting and waiting, due to DSA keeping the refcount forever. DSA would
not access freed memory corresponding to the master interface, but the
unbind would still result in a freeze. Whereas with device links,
graceful teardown is ensured. It even works with cascaded DSA trees.
$ echo 0000:00:00.2 > /sys/bus/pci/drivers/fsl_enetc/unbind
[ 1818.797546] device swp0 left promiscuous mode
[ 1819.301112] sja1105 spi2.0: Link is Down
[ 1819.307981] DSA: tree 1 torn down
[ 1819.312408] device eno2 left promiscuous mode
[ 1819.656803] mscc_felix 0000:00:00.5: Link is Down
[ 1819.667194] DSA: tree 0 torn down
[ 1819.711557] fsl_enetc 0000:00:00.2 eno2: Link is Down
This approach allows us to keep the DSA framework absolutely unchanged,
and the driver core will just know to unbind us first when the master
goes away - as opposed to the large (and probably impossible) rework
required if attempting to listen for NETDEV_UNREGISTER.
As per the documentation at Documentation/driver-api/device_link.rst,
specifying the DL_FLAG_AUTOREMOVE_CONSUMER flag causes the device link
to be automatically purged when the consumer fails to probe or later
unbinds. So we don't need to keep the consumer_link variable in struct
dsa_switch.
Fixes: 6a3226035fc2 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20210111230943.3701806-1-olteanv@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marco Felsch [Mon, 11 Jan 2021 08:59:32 +0000 (09:59 +0100)]
net: phy: smsc: fix clk error handling
Commit e2f7c5d71a15 ("net: phy: smsc: LAN8710/20: add phy refclk in
support") added the phy clk support. The commit already checks if
clk_get_optional() throw an error but instead of returning the error it
ignores it.
Fixes: e2f7c5d71a15 ("net: phy: smsc: LAN8710/20: add phy refclk in support") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210111085932.28680-1-m.felsch@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit f7aab35f4310 ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Andrii Nakryiko [Sun, 10 Jan 2021 07:03:41 +0000 (23:03 -0800)]
libbpf: Allow loading empty BTFs
Empty BTFs do come up (e.g., simple kernel modules with no new types and
strings, compared to the vmlinux BTF) and there is nothing technically wrong
with them. So remove unnecessary check preventing loading empty BTFs.
Fixes: d9d45f409ac9 ("libbpf: Fix BTF data layout checks and allow empty BTF") Reported-by: Christopher William Snowhill <chris@kode54.net> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210110070341.1380086-2-andrii@kernel.org
Andrii Nakryiko [Sun, 10 Jan 2021 07:03:40 +0000 (23:03 -0800)]
bpf: Allow empty module BTFs
Some modules don't declare any new types and end up with an empty BTF,
containing only valid BTF header and no types or strings sections. This
currently causes BTF validation error. There is nothing wrong with such BTF,
so fix the issue by allowing module BTFs with no types or strings.
Fixes: 678fe7ae62a1 ("bpf: Load and verify kernel module BTFs") Reported-by: Christopher William Snowhill <chris@kode54.net> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20210110070341.1380086-1-andrii@kernel.org
bpf: Don't leak memory in bpf getsockopt when optlen == 0
optlen == 0 indicates that the kernel should ignore BPF buffer
and use the original one from the user. We, however, forget
to free the temporary buffer that we've allocated for BPF.
Fixes: 0e957ac1238e ("bpf: Don't return EINVAL from {get,set}sockopt when optlen > PAGE_SIZE") Reported-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/20210112162829.775079-1-sdf@google.com
Linus Torvalds [Tue, 12 Jan 2021 17:38:53 +0000 (09:38 -0800)]
Merge tag 'nfs-for-5.11-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights include:
- Fix parsing of link-local IPv6 addresses
- Fix confusing logging of mount errors that was introduced by the
fsopen() patchset.
- Fix a tracing use after free in _nfs4_do_setlk()
- Layout return-on-close fixes when called from nfs4_evict_inode()
- Layout segments were being leaked in
pnfs_generic_clear_request_commit()
- Don't leak DS commits in pnfs_generic_retry_commit()
- Fix an Oopsable use-after-free when nfs_delegation_find_inode_server()
calls iput() on an inode after the super block has gone away"
* tag 'nfs-for-5.11-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: nfs_igrab_and_active must first reference the superblock
NFS: nfs_delegation_find_inode_server must first reference the superblock
NFS/pNFS: Fix a leak of the layout 'plh_outstanding' counter
NFS/pNFS: Don't leak DS commits in pnfs_generic_retry_commit()
NFS/pNFS: Don't call pnfs_free_bucket_lseg() before removing the request
pNFS: Stricter ordering of layoutget and layoutreturn
pNFS: Clean up pnfs_layoutreturn_free_lsegs()
pNFS: We want return-on-close to complete when evicting the inode
pNFS: Mark layout for return if return-on-close was not sent
net: sunrpc: interpret the return value of kstrtou32 correctly
NFS: Adjust fs_context error logging
NFS4: Fix use-after-free in trace_event_raw_event_nfs4_set_lock
Linus Torvalds [Tue, 12 Jan 2021 17:16:59 +0000 (09:16 -0800)]
Merge tag 'mkp-scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi
Pull SCSI target fix from Martin Petersen:
"This addresses an issue in the SCSI target subsystem. A connected
initiator could specify IDs for any configured backing store device,
not just the ones explicitly made visible to the host.
The remedy is to honor the access control list when doing ID
descriptor lookups"
* tag 'mkp-scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi:
scsi: target: Fix XCOPY NAA identifier lookup
KP Singh [Tue, 12 Jan 2021 07:55:23 +0000 (07:55 +0000)]
bpf: Update local storage test to check handling of null ptrs
It was found in [1] that bpf_inode_storage_get helper did not check
the nullness of the passed owner ptr which caused an oops when
dereferenced. This change incorporates the example suggested in [1] into
the local storage selftest.
The test is updated to create a temporary directory instead of just
using a tempfile. In order to replicate the issue this copied rm binary
is renamed tiggering the inode_rename with a null pointer for the
new_inode. The logic to verify the setting and deletion of the inode
local storage of the old inode is also moved to this LSM hook.
The change also removes the copy_rm function and simply shells out
to copy files and recursively delete directories and consolidates the
logic of setting the initial inode storage to the bprm_committed_creds
hook and removes the file_open hook.
KP Singh [Tue, 12 Jan 2021 07:55:24 +0000 (07:55 +0000)]
bpf: Local storage helpers should check nullness of owner ptr passed
The verifier allows ARG_PTR_TO_BTF_ID helper arguments to be NULL, so
helper implementations need to check this before dereferencing them.
This was already fixed for the socket storage helpers but not for task
and inode.
The issue can be reproduced by attaching an LSM program to
inode_rename hook (called when moving files) which tries to get the
inode of the new file without checking for its nullness and then trying
to move an existing file to a new path:
mv existing_file new_file_does_not_exist
The report including the sample program and the steps for reproducing
the bug:
Peter Geis [Fri, 8 Jan 2021 13:59:13 +0000 (13:59 +0000)]
ALSA: hda/tegra: fix tegra-hda on tegra30 soc
Currently hda on tegra30 fails to open a stream with an input/output error.
For example:
speaker-test -Dhw:0,3 -c 2
speaker-test 1.2.2
Playback device is hw:0,3
Stream parameters are 48000Hz, S16_LE, 2 channels
Using 16 octaves of pink noise
Rate set to 48000Hz (requested 48000Hz)
Buffer size range from 64 to 16384
Period size range from 32 to 8192
Using max buffer size 16384
Periods = 4
was set period_size = 4096
was set buffer_size = 16384
0 - Front Left
Write error: -5,Input/output error
xrun_recovery failed: -5,Input/output error
Transfer failed: Input/output error
The tegra-hda device was introduced in tegra30 but only utilized in
tegra124 until recent chips. Tegra210/186 work only due to a hardware
change. For this reason it is unknown when this issue first manifested.
Discussions with the hardware team show this applies to all current tegra
chips. It has been resolved in the tegra234, which does not have hda
support at this time.
The explanation from the hardware team is this:
Below is the striping formula referenced from HD audio spec.
{ ((num_channels * bits_per_sample) / number of SDOs) >= 8 }
The current issue is seen because Tegra HW has a problem with boundary
condition (= 8) for striping. The reason why it is not seen on
Tegra210/Tegra186 is because it uses max 2SDO lines. Max SDO lines is
read from GCAP register.
For the given stream (channels = 2, bps = 16);
ratio = (channels * bps) / NSDO = 32 / NSDO;
On Tegra30, ratio = 32/4 = 8 (FAIL)
On Tegra210/186, ratio = 32/2 = 16 (PASS)
On Tegra194, ratio = 32/4 = 8 (FAIL) ==> Earlier workaround was
applied for it
If Tegra210/186 is forced to use 4SDO, it fails there as well. So the
behavior is consistent across all these chips.
Applying the fix in [1] universally resolves this issue on tegra30-hda.
Tested on the Ouya game console and the tf201 tablet.
[1] commit 16e6eaa3abc3 ("ALSA: hda/tegra: workaround playback failure on
Tegra194")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Ion Agorria <ion@agorria.com> Reviewed-by: Sameer Pujar <spujar@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Peter Geis <pgwipeout@gmail.com> Link: https://lore.kernel.org/r/20210108135913.2421585-3-pgwipeout@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
Peter Geis [Fri, 8 Jan 2021 13:59:12 +0000 (13:59 +0000)]
clk: tegra30: Add hda clock default rates to clock driver
Current implementation defaults the hda clocks to clk_m. This causes hda
to run too slow to operate correctly. Fix this by defaulting to pll_p and
setting the frequency to the correct rate.
This matches upstream t124 and downstream t30.
Acked-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Ion Agorria <ion@agorria.com> Acked-by: Sameer Pujar <spujar@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Peter Geis <pgwipeout@gmail.com> Link: https://lore.kernel.org/r/20210108135913.2421585-2-pgwipeout@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jakub Kicinski [Tue, 12 Jan 2021 02:20:12 +0000 (18:20 -0800)]
Merge branch 'skb-frag-kmap_atomic-fixes'
Willem de Bruijn says:
====================
skb frag: kmap_atomic fixes
skb frags may be backed by highmem and/or compound pages. Various
code calls kmap_atomic to safely access highmem pages. But this
needs additional care for compound pages. Fix a few issues:
patch 1 expect kmap mappings with CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP
patch 2 fixes kmap_atomic + compound page support in skb_seq_read
patch 3 fixes kmap_atomic + compound page support in esp
====================
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for
the esp trailer.
It accesses the page with kmap_atomic to handle highmem. But
skb_page_frag_refill can return compound pages, of which
kmap_atomic only maps the first underlying page.
skb_page_frag_refill does not return highmem, because flag
__GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP.
That also does not call kmap_atomic, but directly uses page_address,
in skb_copy_to_page_nocache. Do the same for ESP.
This issue has become easier to trigger with recent kmap local
debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP.
Fixes: 1f6f9496b0f0 ("esp4: Avoid skb_cow_data whenever possible") Fixes: 73a7b070a864 ("esp6: Avoid skb_cow_data whenever possible") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
skb_seq_read iterates over an skb, returning pointer and length of
the next data range with each call.
It relies on kmap_atomic to access highmem pages when needed.
An skb frag may be backed by a compound page, but kmap_atomic maps
only a single page. There are not enough kmap slots to always map all
pages concurrently.
Instead, if kmap_atomic is needed, iterate over each page.
As this increases the number of calls, avoid this unless needed.
The necessary condition is captured in skb_frag_must_loop.
I tried to make the change as obvious as possible. It should be easy
to verify that nothing changes if skb_frag_must_loop returns false.
Tested:
On an x86 platform with
CONFIG_HIGHMEM=y
CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP=y
CONFIG_NETFILTER_XT_MATCH_STRING=y
Run
ip link set dev lo mtu 1500
iptables -A OUTPUT -m string --string 'badstring' -algo bm -j ACCEPT
dd if=/dev/urandom of=in bs=1M count=20
nc -l -p 8000 > /dev/null &
nc -w 1 -q 0 localhost 8000 < in
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: support kmap_local forced debugging in skb_frag_foreach
Skb frags may be backed by highmem and/or compound pages. Highmem
pages need kmap_atomic mappings to access. But kmap_atomic maps a
single page, not the entire compound page.
skb_foreach_page iterates over an skb frag, in one step in the common
case, page by page only if kmap_atomic must be called for each page.
The decision logic is captured in skb_frag_must_loop.
CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP extends kmap from highmem to all
pages, to increase code coverage.
Extend skb_frag_must_loop to this new condition.
Link: https://lore.kernel.org/linux-mm/20210106180132.41dc249d@gandalf.local.home/ Fixes: f9c91964ac4f ("mm/highmem: Provide CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP") Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Willem de Bruijn <willemb@google.com> Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rndis_host: set proper input size for OID_GEN_PHYSICAL_MEDIUM request
MSFT ActiveSync implementation requires that the size of the response for
incoming query is to be provided in the request input length. Failure to
set the input size proper results in failed request transfer, where the
ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L)
error.
Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size
of the response in order for the ActiveSync to properly respond to the
request.
Linus Torvalds [Mon, 11 Jan 2021 22:37:13 +0000 (14:37 -0800)]
Merge tag 'trace-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Blacklist properly on all archs.
The code to blacklist notrace functions for kprobes was not using the
right kconfig option, which caused some archs (powerpc) to possibly
not blacklist them"
* tag 'trace-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Do the notrace functions check without kprobes on ftrace
- debugging fixups:
- print correct offset for reloc tree key
- pass reliable fs_info pointer to error reporting helper"
* tag 'for-5.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: shrink delalloc pages instead of full inodes
btrfs: reloc: fix wrong file extent type check to avoid false ENOENT
btrfs: tree-checker: check if chunk item end overflows
btrfs: prevent NULL pointer dereference in extent_io_tree_panic
btrfs: print the actual offset in btrfs_root_name
When attempting to match EXTENDED COPY CSCD descriptors with corresponding
se_devices, target_xcopy_locate_se_dev_e4() currently iterates over LIO's
global devices list which includes all configured backstores.
This change ensures that only initiator-accessible backstores are
considered during CSCD descriptor lookup, according to the session's
se_node_acl LUN list.
To avoid LUN removal race conditions, device pinning is changed from being
configfs based to instead using the se_node_acl lun_ref.
Reference: CVE-2020-28374 Fixes: 5966b2333141 ("target: Add support for EXTENDED_COPY copy offload emulation") Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tracing/kprobes: Do the notrace functions check without kprobes on ftrace
Enable the notrace function check on the architecture which doesn't
support kprobes on ftrace but support dynamic ftrace. This notrace
function check is not only for the kprobes on ftrace but also
sw-breakpoint based kprobes.
Thus there is no reason to limit this check for the arch which
supports kprobes on ftrace.
This also changes the dependency of Kconfig. Because kprobe event
uses the function tracer's address list for identifying notrace
function, if the CONFIG_DYNAMIC_FTRACE=n, it can not check whether
the target function is notrace or not.
Linus Torvalds [Mon, 11 Jan 2021 19:35:46 +0000 (11:35 -0800)]
Merge tag 'nfsd-5.11-1' of git://git.linux-nfs.org/projects/cel/cel-2.6
Pull nfsd fixes from Chuck Lever:
- Fix major TCP performance regression
- Get NFSv4.2 READ_PLUS regression tests to pass
- Improve NFSv4 COMPOUND memory allocation
- Fix sparse warning
* tag 'nfsd-5.11-1' of git://git.linux-nfs.org/projects/cel/cel-2.6:
NFSD: Restore NFSv4 decoding's SAVEMEM functionality
SUNRPC: Handle TCP socket sends with kernel_sendpage() again
NFSD: Fix sparse warning in nfssvc.c
nfsd: Don't set eof on a truncated READ_PLUS
nfsd: Fixes for nfsd4_encode_read_plus_data()
Linus Torvalds [Mon, 11 Jan 2021 19:28:58 +0000 (11:28 -0800)]
Merge tag 'hyperv-fixes-signed-20210111' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- fix kexec panic/hang (Dexuan Cui)
- fix occasional crashes when flushing TLB (Wei Liu)
* tag 'hyperv-fixes-signed-20210111' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: check cpu mask after interrupt has been disabled
x86/hyperv: Fix kexec panic/hang issues
projects / kernel.git / log