#define FEATURE_SMNCLK_DPM_BIT 47
#define FEATURE_PERLINK_GMIDOWN_BIT 48
#define FEATURE_GFX_EDC_BIT 49
-#define FEATURE_SPARE_50_BIT 50
-#define FEATURE_SPARE_51_BIT 51
+#define FEATURE_GFX_PER_PART_VMIN_BIT 50
+#define FEATURE_SMART_SHIFT_BIT 51
#define FEATURE_SPARE_52_BIT 52
#define FEATURE_SPARE_53_BIT 53
#define FEATURE_SPARE_54_BIT 54
} PPTable_t;
+typedef struct {
+ // MAJOR SECTION: SKU PARAMETERS
+
+ uint32_t Version;
+
+ // SECTION: Feature Enablement
+ uint32_t FeaturesToRun[NUM_FEATURES / 32];
+
+ // SECTION: Infrastructure Limits
+ uint16_t SocketPowerLimitAc[PPT_THROTTLER_COUNT]; // Watts
+ uint16_t SocketPowerLimitAcTau[PPT_THROTTLER_COUNT]; // Time constant of LPF in ms
+ uint16_t SocketPowerLimitDc[PPT_THROTTLER_COUNT]; // Watts
+ uint16_t SocketPowerLimitDcTau[PPT_THROTTLER_COUNT]; // Time constant of LPF in ms
+
+ uint16_t TdcLimit[TDC_THROTTLER_COUNT]; // Amps
+ uint16_t TdcLimitTau[TDC_THROTTLER_COUNT]; // Time constant of LPF in ms
+
+ uint16_t TemperatureLimit[TEMP_COUNT]; // Celcius
+
+ uint32_t FitLimit; // Failures in time (failures per million parts over the defined lifetime)
+
+ // SECTION: Power Configuration
+ uint8_t TotalPowerConfig; //0-TDP, 1-TGP, 2-TCP Estimated, 3-TCP Measured. Use defines from PwrConfig_e
+ uint8_t TotalPowerPadding[3];
+
+ // SECTION: APCC Settings
+ uint32_t ApccPlusResidencyLimit;
+
+ //SECTION: SMNCLK DPM
+ uint16_t SmnclkDpmFreq [NUM_SMNCLK_DPM_LEVELS]; // in MHz
+ uint16_t SmnclkDpmVoltage [NUM_SMNCLK_DPM_LEVELS]; // mV(Q2)
+
+ uint32_t PaddingAPCC;
+ uint16_t PerPartDroopVsetGfxDfll[NUM_PIECE_WISE_LINEAR_DROOP_MODEL_VF_POINTS]; //In mV(Q2)
+ uint16_t PaddingPerPartDroop;
+
+ // SECTION: Throttler settings
+ uint32_t ThrottlerControlMask; // See Throtter masks defines
+
+ // SECTION: FW DSTATE Settings
+ uint32_t FwDStateMask; // See FW DState masks defines
+
+ // SECTION: ULV Settings
+ uint16_t UlvVoltageOffsetSoc; // In mV(Q2)
+ uint16_t UlvVoltageOffsetGfx; // In mV(Q2)
+
+ uint16_t MinVoltageUlvGfx; // In mV(Q2) Minimum Voltage ("Vmin") of VDD_GFX in ULV mode
+ uint16_t MinVoltageUlvSoc; // In mV(Q2) Minimum Voltage ("Vmin") of VDD_SOC in ULV mode
+
+ uint16_t SocLIVmin;
+ uint16_t SocLIVminoffset;
+
+ uint8_t GceaLinkMgrIdleThreshold; //Set by SMU FW during enablment of GFXOFF. Controls delay for GFX SDP port disconnection during idle events
+ uint8_t paddingRlcUlvParams[3];
+
+ // SECTION: Voltage Control Parameters
+ uint16_t MinVoltageGfx; // In mV(Q2) Minimum Voltage ("Vmin") of VDD_GFX
+ uint16_t MinVoltageSoc; // In mV(Q2) Minimum Voltage ("Vmin") of VDD_SOC
+ uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX
+ uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC
+
+ uint16_t LoadLineResistanceGfx; // In mOhms with 8 fractional bits
+ uint16_t LoadLineResistanceSoc; // In mOhms with 8 fractional bits
+
+ // SECTION: Temperature Dependent Vmin
+ uint16_t VDDGFX_TVmin; //Celcius
+ uint16_t VDDSOC_TVmin; //Celcius
+ uint16_t VDDGFX_Vmin_HiTemp; // mV Q2
+ uint16_t VDDGFX_Vmin_LoTemp; // mV Q2
+ uint16_t VDDSOC_Vmin_HiTemp; // mV Q2
+ uint16_t VDDSOC_Vmin_LoTemp; // mV Q2
+
+ uint16_t VDDGFX_TVminHystersis; // Celcius
+ uint16_t VDDSOC_TVminHystersis; // Celcius
+
+ //SECTION: DPM Config 1
+ DpmDescriptor_t DpmDescriptor[PPCLK_COUNT];
+
+ uint16_t FreqTableGfx [NUM_GFXCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableVclk [NUM_VCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableDclk [NUM_DCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableSocclk [NUM_SOCCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableUclk [NUM_UCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableDcefclk [NUM_DCEFCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableDispclk [NUM_DISPCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTablePixclk [NUM_PIXCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTablePhyclk [NUM_PHYCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableDtbclk [NUM_DTBCLK_DPM_LEVELS ]; // In MHz
+ uint16_t FreqTableFclk [NUM_FCLK_DPM_LEVELS ]; // In MHz
+ uint32_t Paddingclks;
+
+ DroopInt_t PerPartDroopModelGfxDfll[NUM_PIECE_WISE_LINEAR_DROOP_MODEL_VF_POINTS]; //GHz ->Vstore in IEEE float format
+
+ uint32_t DcModeMaxFreq [PPCLK_COUNT ]; // In MHz
+
+ uint8_t FreqTableUclkDiv [NUM_UCLK_DPM_LEVELS ]; // 0:Div-1, 1:Div-1/2, 2:Div-1/4, 3:Div-1/8
+
+ // Used for MALL performance boost
+ uint16_t FclkBoostFreq; // In Mhz
+ uint16_t FclkParamPadding;
+
+ // SECTION: DPM Config 2
+ uint16_t Mp0clkFreq [NUM_MP0CLK_DPM_LEVELS]; // in MHz
+ uint16_t Mp0DpmVoltage [NUM_MP0CLK_DPM_LEVELS]; // mV(Q2)
+ uint16_t MemVddciVoltage [NUM_UCLK_DPM_LEVELS]; // mV(Q2)
+ uint16_t MemMvddVoltage [NUM_UCLK_DPM_LEVELS]; // mV(Q2)
+ // GFXCLK DPM
+ uint16_t GfxclkFgfxoffEntry; // in Mhz
+ uint16_t GfxclkFinit; // in Mhz
+ uint16_t GfxclkFidle; // in MHz
+ uint8_t GfxclkSource; // 0 = PLL, 1 = DFLL
+ uint8_t GfxclkPadding;
+
+ // GFX GPO
+ uint8_t GfxGpoSubFeatureMask; // bit 0 = PACE, bit 1 = DEM
+ uint8_t GfxGpoEnabledWorkPolicyMask; //Any policy that GPO can be enabled
+ uint8_t GfxGpoDisabledWorkPolicyMask; //Any policy that GPO can be disabled
+ uint8_t GfxGpoPadding[1];
+ uint32_t GfxGpoVotingAllow; //For indicating which feature changes should result in a GPO table recalculation
+
+ uint32_t GfxGpoPadding32[4];
+
+ uint16_t GfxDcsFopt; // Optimal GFXCLK for DCS in Mhz
+ uint16_t GfxDcsFclkFopt; // Optimal FCLK for DCS in Mhz
+ uint16_t GfxDcsUclkFopt; // Optimal UCLK for DCS in Mhz
+
+ uint16_t DcsGfxOffVoltage; //Voltage in mV(Q2) applied to VDDGFX when entering DCS GFXOFF phase
+
+ uint16_t DcsMinGfxOffTime; //Minimum amount of time PMFW shuts GFX OFF as part of GFX DCS phase
+ uint16_t DcsMaxGfxOffTime; //Maximum amount of time PMFW can shut GFX OFF as part of GFX DCS phase at a stretch.
+
+ uint32_t DcsMinCreditAccum; //Min amount of positive credit accumulation before waking GFX up as part of DCS.
+
+ uint16_t DcsExitHysteresis; //The min amount of time power credit accumulator should have a value > 0 before SMU exits the DCS throttling phase.
+ uint16_t DcsTimeout; //This is the amount of time SMU FW waits for RLC to put GFX into GFXOFF before reverting to the fallback mechanism of throttling GFXCLK to Fmin.
+
+ uint32_t DcsParamPadding[5];
+
+ uint16_t FlopsPerByteTable[RLC_PACE_TABLE_NUM_LEVELS]; // Q8.8
+
+ // UCLK section
+ uint8_t LowestUclkReservedForUlv; // Set this to 1 if UCLK DPM0 is reserved for ULV-mode only
+ uint8_t PaddingMem[3];
+
+ uint8_t UclkDpmPstates [NUM_UCLK_DPM_LEVELS]; // 4 DPM states, 0-P0, 1-P1, 2-P2, 3-P3.
+
+ // Used for 2-Step UCLK change workaround
+ UclkDpmChangeRange_t UclkDpmSrcFreqRange; // In Mhz
+ UclkDpmChangeRange_t UclkDpmTargFreqRange; // In Mhz
+ uint16_t UclkDpmMidstepFreq; // In Mhz
+ uint16_t UclkMidstepPadding;
+
+ // Link DPM Settings
+ uint8_t PcieGenSpeed[NUM_LINK_LEVELS]; ///< 0:PciE-gen1 1:PciE-gen2 2:PciE-gen3 3:PciE-gen4
+ uint8_t PcieLaneCount[NUM_LINK_LEVELS]; ///< 1=x1, 2=x2, 3=x4, 4=x8, 5=x12, 6=x16
+ uint16_t LclkFreq[NUM_LINK_LEVELS];
+
+ // SECTION: Fan Control
+ uint16_t FanStopTemp; //Celcius
+ uint16_t FanStartTemp; //Celcius
+
+ uint16_t FanGain[TEMP_COUNT];
+
+ uint16_t FanPwmMin;
+ uint16_t FanAcousticLimitRpm;
+ uint16_t FanThrottlingRpm;
+ uint16_t FanMaximumRpm;
+ uint16_t MGpuFanBoostLimitRpm;
+ uint16_t FanTargetTemperature;
+ uint16_t FanTargetGfxclk;
+ uint16_t FanPadding16;
+ uint8_t FanTempInputSelect;
+ uint8_t FanPadding;
+ uint8_t FanZeroRpmEnable;
+ uint8_t FanTachEdgePerRev;
+
+ // The following are AFC override parameters. Leave at 0 to use FW defaults.
+ int16_t FuzzyFan_ErrorSetDelta;
+ int16_t FuzzyFan_ErrorRateSetDelta;
+ int16_t FuzzyFan_PwmSetDelta;
+ uint16_t FuzzyFan_Reserved;
+
+ // SECTION: AVFS
+ // Overrides
+ uint8_t OverrideAvfsGb[AVFS_VOLTAGE_COUNT];
+ uint8_t dBtcGbGfxDfllModelSelect; //0 -> fused piece-wise model, 1 -> piece-wise linear(PPTable), 2 -> quadratic model(PPTable)
+ uint8_t Padding8_Avfs;
+
+ QuadraticInt_t qAvfsGb[AVFS_VOLTAGE_COUNT]; // GHz->V Override of fused curve
+ DroopInt_t dBtcGbGfxPll; // GHz->V BtcGb
+ DroopInt_t dBtcGbGfxDfll; // GHz->V BtcGb
+ DroopInt_t dBtcGbSoc; // GHz->V BtcGb
+ LinearInt_t qAgingGb[AVFS_VOLTAGE_COUNT]; // GHz->V
+
+ PiecewiseLinearDroopInt_t PiecewiseLinearDroopIntGfxDfll; //GHz ->Vstore in IEEE float format
+
+ QuadraticInt_t qStaticVoltageOffset[AVFS_VOLTAGE_COUNT]; // GHz->V
+
+ uint16_t DcTol[AVFS_VOLTAGE_COUNT]; // mV Q2
+
+ uint8_t DcBtcEnabled[AVFS_VOLTAGE_COUNT];
+ uint8_t Padding8_GfxBtc[2];
+
+ uint16_t DcBtcMin[AVFS_VOLTAGE_COUNT]; // mV Q2
+ uint16_t DcBtcMax[AVFS_VOLTAGE_COUNT]; // mV Q2
+
+ uint16_t DcBtcGb[AVFS_VOLTAGE_COUNT]; // mV Q2
+
+ // SECTION: XGMI
+ uint8_t XgmiDpmPstates[NUM_XGMI_LEVELS]; // 2 DPM states, high and low. 0-P0, 1-P1, 2-P2, 3-P3.
+ uint8_t XgmiDpmSpare[2];
+
+ // SECTION: Advanced Options
+ uint32_t DebugOverrides;
+ QuadraticInt_t ReservedEquation0;
+ QuadraticInt_t ReservedEquation1;
+ QuadraticInt_t ReservedEquation2;
+ QuadraticInt_t ReservedEquation3;
+
+ // SECTION: Sku Reserved
+ uint8_t CustomerVariant;
+
+ //VC BTC parameters are only applicable to VDD_GFX domain
+ uint8_t VcBtcEnabled;
+ uint16_t VcBtcVminT0; // T0_VMIN
+ uint16_t VcBtcFixedVminAgingOffset; // FIXED_VMIN_AGING_OFFSET
+ uint16_t VcBtcVmin2PsmDegrationGb; // VMIN_TO_PSM_DEGRADATION_GB
+ uint32_t VcBtcPsmA; // A_PSM
+ uint32_t VcBtcPsmB; // B_PSM
+ uint32_t VcBtcVminA; // A_VMIN
+ uint32_t VcBtcVminB; // B_VMIN
+
+ //GPIO Board feature
+ uint16_t LedGpio; //GeneriA GPIO flag used to control the radeon LEDs
+ uint16_t GfxPowerStagesGpio; //Genlk_vsync GPIO flag used to control gfx power stages
+
+ uint32_t SkuReserved[16];
+
+
+
+ // MAJOR SECTION: BOARD PARAMETERS
+
+ //SECTION: Gaming Clocks
+ uint32_t GamingClk[6];
+
+ // SECTION: I2C Control
+ I2cControllerConfig_t I2cControllers[NUM_I2C_CONTROLLERS];
+
+ uint8_t GpioScl; // GPIO Number for SCL Line, used only for CKSVII2C1
+ uint8_t GpioSda; // GPIO Number for SDA Line, used only for CKSVII2C1
+ uint8_t FchUsbPdSlaveAddr; //For requesting USB PD controller S-states via FCH I2C when entering PME turn off
+ uint8_t I2cSpare[1];
+
+ // SECTION: SVI2 Board Parameters
+ uint8_t VddGfxVrMapping; // Use VR_MAPPING* bitfields
+ uint8_t VddSocVrMapping; // Use VR_MAPPING* bitfields
+ uint8_t VddMem0VrMapping; // Use VR_MAPPING* bitfields
+ uint8_t VddMem1VrMapping; // Use VR_MAPPING* bitfields
+
+ uint8_t GfxUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+ uint8_t SocUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+ uint8_t VddciUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+ uint8_t MvddUlvPhaseSheddingMask; // set this to 1 to set PSI0/1 to 1 in ULV mode
+
+ // SECTION: Telemetry Settings
+ uint16_t GfxMaxCurrent; // in Amps
+ int8_t GfxOffset; // in Amps
+ uint8_t Padding_TelemetryGfx;
+
+ uint16_t SocMaxCurrent; // in Amps
+ int8_t SocOffset; // in Amps
+ uint8_t Padding_TelemetrySoc;
+
+ uint16_t Mem0MaxCurrent; // in Amps
+ int8_t Mem0Offset; // in Amps
+ uint8_t Padding_TelemetryMem0;
+
+ uint16_t Mem1MaxCurrent; // in Amps
+ int8_t Mem1Offset; // in Amps
+ uint8_t Padding_TelemetryMem1;
+
+ uint32_t MvddRatio; // This is used for MVDD Svi2 Div Ratio workaround. It has 16 fractional bits (Q16.16)
+
+ // SECTION: GPIO Settings
+ uint8_t AcDcGpio; // GPIO pin configured for AC/DC switching
+ uint8_t AcDcPolarity; // GPIO polarity for AC/DC switching
+ uint8_t VR0HotGpio; // GPIO pin configured for VR0 HOT event
+ uint8_t VR0HotPolarity; // GPIO polarity for VR0 HOT event
+
+ uint8_t VR1HotGpio; // GPIO pin configured for VR1 HOT event
+ uint8_t VR1HotPolarity; // GPIO polarity for VR1 HOT event
+ uint8_t GthrGpio; // GPIO pin configured for GTHR Event
+ uint8_t GthrPolarity; // replace GPIO polarity for GTHR
+
+ // LED Display Settings
+ uint8_t LedPin0; // GPIO number for LedPin[0]
+ uint8_t LedPin1; // GPIO number for LedPin[1]
+ uint8_t LedPin2; // GPIO number for LedPin[2]
+ uint8_t LedEnableMask;
+
+ uint8_t LedPcie; // GPIO number for PCIE results
+ uint8_t LedError; // GPIO number for Error Cases
+ uint8_t LedSpare1[2];
+
+ // SECTION: Clock Spread Spectrum
+
+ // GFXCLK PLL Spread Spectrum
+ uint8_t PllGfxclkSpreadEnabled; // on or off
+ uint8_t PllGfxclkSpreadPercent; // Q4.4
+ uint16_t PllGfxclkSpreadFreq; // kHz
+
+ // GFXCLK DFLL Spread Spectrum
+ uint8_t DfllGfxclkSpreadEnabled; // on or off
+ uint8_t DfllGfxclkSpreadPercent; // Q4.4
+ uint16_t DfllGfxclkSpreadFreq; // kHz
+
+ // UCLK Spread Spectrum
+ uint16_t UclkSpreadPadding;
+ uint16_t UclkSpreadFreq; // kHz
+
+ // FCLK Spread Spectrum
+ uint8_t FclkSpreadEnabled; // on or off
+ uint8_t FclkSpreadPercent; // Q4.4
+ uint16_t FclkSpreadFreq; // kHz
+
+ // Section: Memory Config
+ uint32_t MemoryChannelEnabled; // For DRAM use only, Max 32 channels enabled bit mask.
+
+ uint8_t DramBitWidth; // For DRAM use only. See Dram Bit width type defines
+ uint8_t PaddingMem1[3];
+
+ // Section: Total Board Power
+ uint16_t TotalBoardPower; //Only needed for TCP Estimated case, where TCP = TGP+Total Board Power
+ uint16_t BoardPowerPadding;
+
+ // SECTION: XGMI Training
+ uint8_t XgmiLinkSpeed [NUM_XGMI_PSTATE_LEVELS];
+ uint8_t XgmiLinkWidth [NUM_XGMI_PSTATE_LEVELS];
+
+ uint16_t XgmiFclkFreq [NUM_XGMI_PSTATE_LEVELS];
+ uint16_t XgmiSocVoltage [NUM_XGMI_PSTATE_LEVELS];
+
+ // SECTION: UMC feature flags
+ uint8_t HsrEnabled;
+ uint8_t VddqOffEnabled;
+ uint8_t PaddingUmcFlags[2];
+
+ // UCLK Spread Spectrum
+ uint8_t UclkSpreadPercent[16];
+
+ // SECTION: Board Reserved
+ uint32_t BoardReserved[11];
+
+ // SECTION: Structure Padding
+
+ // Padding for MMHUB - do not modify this
+ uint32_t MmHubPadding[8]; // SMU internal use
+
+
+} PPTable_beige_goby_t;
+
typedef struct {
// Time constant parameters for clock averages in ms
uint16_t GfxclkAverageLpfTau;
// These defines are used with the SMC_MSG_SetUclkFastSwitch message.
#define UCLK_SWITCH_SLOW 0
#define UCLK_SWITCH_FAST 1
+#define UCLK_SWITCH_DUMMY 2
#endif
projects / kernel.git / commitdiff