]> git.baikalelectronics.ru Git - uboot.git/commitdiff
net: dwc_eth_qos: Add Qcom ethernet driver glue layer
authorSumit Garg <sumit.garg@linaro.org>
Wed, 1 Feb 2023 13:58:55 +0000 (19:28 +0530)
committerTom Rini <trini@konsulko.com>
Fri, 10 Feb 2023 17:50:00 +0000 (12:50 -0500)
The Qualcom ETHQOS hardware supports an RGMII macro which needs to be
configured according to following link speeds:
- SPEED_1000
- SPEED_100
- SPEED_10

So add a corresponding glue driver to configure RGMII macro.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
drivers/net/Kconfig
drivers/net/Makefile
drivers/net/dwc_eth_qos.c
drivers/net/dwc_eth_qos.h
drivers/net/dwc_eth_qos_qcom.c [new file with mode: 0644]

index 62d2c03849afca0c8d5367c15d028c3f4b7b9eba..3816d05525cd7e16c2db1107fecdfea601fb74eb 100644 (file)
@@ -242,6 +242,13 @@ config DWC_ETH_QOS_TEGRA186
          The Synopsys Designware Ethernet QOS IP block with specific
          configuration used in NVIDIA's Tegra186 chip.
 
+config DWC_ETH_QOS_QCOM
+       bool "Synopsys DWC Ethernet QOS device support for Qcom SoCs"
+       depends on DWC_ETH_QOS
+       help
+         The Synopsys Designware Ethernet QOS IP block with specific
+         configuration used in Qcom QCS404 SoC.
+
 config E1000
        bool "Intel PRO/1000 Gigabit Ethernet support"
        depends on PCI
index 90fbb02ab02d28ea4df54816b0c54361d185da19..75daa5e694ce01ad5b22b903667bfdfc2bd88142 100644 (file)
@@ -20,6 +20,7 @@ obj-$(CONFIG_DRIVER_DM9000) += dm9000x.o
 obj-$(CONFIG_DSA_SANDBOX) += dsa_sandbox.o
 obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
 obj-$(CONFIG_DWC_ETH_QOS_IMX) += dwc_eth_qos_imx.o
+obj-$(CONFIG_DWC_ETH_QOS_QCOM) += dwc_eth_qos_qcom.o
 obj-$(CONFIG_E1000) += e1000.o
 obj-$(CONFIG_E1000_SPI) += e1000_spi.o
 obj-$(CONFIG_EEPRO100) += eepro100.o
index 65b8556be2837ff61a7f63ae50e6819786194c88..112deb546dec7f22c2e26fd9ef8bec5a556f199c 100644 (file)
@@ -1712,6 +1712,13 @@ static const struct udevice_id eqos_ids[] = {
        },
 #endif
 
+#if IS_ENABLED(CONFIG_DWC_ETH_QOS_QCOM)
+       {
+               .compatible = "qcom,qcs404-ethqos",
+               .data = (ulong)&eqos_qcom_config
+       },
+#endif
+
        { }
 };
 
index 466a792de7a483c8818598ee8fc2adfd00f68e5d..fddbe9336c9bdc705932ca96d597d05bf4979a1a 100644 (file)
@@ -253,6 +253,7 @@ struct eqos_priv {
        struct eqos_mtl_regs *mtl_regs;
        struct eqos_dma_regs *dma_regs;
        struct eqos_tegra186_regs *tegra186_regs;
+       void *eqos_qcom_rgmii_regs;
        struct reset_ctl reset_ctl;
        struct gpio_desc phy_reset_gpio;
        struct clk clk_master_bus;
@@ -277,6 +278,7 @@ struct eqos_priv {
        bool reg_access_ok;
        bool clk_ck_enabled;
        unsigned int tx_fifo_sz, rx_fifo_sz;
+       u32 reset_delays[3];
 };
 
 void eqos_inval_desc_generic(void *desc);
@@ -286,3 +288,4 @@ void eqos_flush_buffer_generic(void *buf, size_t size);
 int eqos_null_ops(struct udevice *dev);
 
 extern struct eqos_config eqos_imx_config;
+extern struct eqos_config eqos_qcom_config;
diff --git a/drivers/net/dwc_eth_qos_qcom.c b/drivers/net/dwc_eth_qos_qcom.c
new file mode 100644 (file)
index 0000000..df83f1c
--- /dev/null
@@ -0,0 +1,612 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2022-2023 Sumit Garg <sumit.garg@linaro.org>
+ *
+ * Qcom DWMAC specific glue layer
+ */
+
+#include <common.h>
+#include <asm/global_data.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <clk.h>
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <phy.h>
+#include <reset.h>
+#include <syscon.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+
+#include "dwc_eth_qos.h"
+
+/* RGMII_IO_MACRO_CONFIG fields */
+#define RGMII_CONFIG_FUNC_CLK_EN               BIT(30)
+#define RGMII_CONFIG_POS_NEG_DATA_SEL          BIT(23)
+#define RGMII_CONFIG_GPIO_CFG_RX_INT           GENMASK(21, 20)
+#define RGMII_CONFIG_GPIO_CFG_TX_INT           GENMASK(19, 17)
+#define RGMII_CONFIG_MAX_SPD_PRG_9             GENMASK(16, 8)
+#define RGMII_CONFIG_MAX_SPD_PRG_2             GENMASK(7, 6)
+#define RGMII_CONFIG_INTF_SEL                  GENMASK(5, 4)
+#define RGMII_CONFIG_BYPASS_TX_ID_EN           BIT(3)
+#define RGMII_CONFIG_LOOPBACK_EN               BIT(2)
+#define RGMII_CONFIG_PROG_SWAP                 BIT(1)
+#define RGMII_CONFIG_DDR_MODE                  BIT(0)
+
+/* SDCC_HC_REG_DLL_CONFIG fields */
+#define SDCC_DLL_CONFIG_DLL_RST                        BIT(30)
+#define SDCC_DLL_CONFIG_PDN                    BIT(29)
+#define SDCC_DLL_CONFIG_MCLK_FREQ              GENMASK(26, 24)
+#define SDCC_DLL_CONFIG_CDR_SELEXT             GENMASK(23, 20)
+#define SDCC_DLL_CONFIG_CDR_EXT_EN             BIT(19)
+#define SDCC_DLL_CONFIG_CK_OUT_EN              BIT(18)
+#define SDCC_DLL_CONFIG_CDR_EN                 BIT(17)
+#define SDCC_DLL_CONFIG_DLL_EN                 BIT(16)
+#define SDCC_DLL_MCLK_GATING_EN                        BIT(5)
+#define SDCC_DLL_CDR_FINE_PHASE                        GENMASK(3, 2)
+
+/* SDCC_HC_REG_DDR_CONFIG fields */
+#define SDCC_DDR_CONFIG_PRG_DLY_EN             BIT(31)
+#define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY       GENMASK(26, 21)
+#define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE  GENMASK(29, 27)
+#define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN    BIT(30)
+#define SDCC_DDR_CONFIG_PRG_RCLK_DLY           GENMASK(8, 0)
+
+/* SDCC_HC_REG_DLL_CONFIG2 fields */
+#define SDCC_DLL_CONFIG2_DLL_CLOCK_DIS         BIT(21)
+#define SDCC_DLL_CONFIG2_MCLK_FREQ_CALC                GENMASK(17, 10)
+#define SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SEL  GENMASK(3, 2)
+#define SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW   BIT(1)
+#define SDCC_DLL_CONFIG2_DDR_CAL_EN            BIT(0)
+
+/* SDC4_STATUS bits */
+#define SDC4_STATUS_DLL_LOCK                   BIT(7)
+
+/* RGMII_IO_MACRO_CONFIG2 fields */
+#define RGMII_CONFIG2_RSVD_CONFIG15            GENMASK(31, 17)
+#define RGMII_CONFIG2_RGMII_CLK_SEL_CFG                BIT(16)
+#define RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN     BIT(13)
+#define RGMII_CONFIG2_CLK_DIVIDE_SEL           BIT(12)
+#define RGMII_CONFIG2_RX_PROG_SWAP             BIT(7)
+#define RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL      BIT(6)
+#define RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN    BIT(5)
+
+struct dwmac_rgmii_regs {
+       u32 io_macro_config;            /* 0x00 */
+       u32 sdcc_hc_dll_config;         /* 0x04 */
+       u32 reserved_1;                 /* 0x08 */
+       u32 sdcc_hc_ddr_config;         /* 0x0c */
+       u32 sdcc_hc_dll_config2;        /* 0x10 */
+       u32 sdc4_status;                /* 0x14 */
+       u32 sdcc_usr_ctl;               /* 0x18 */
+       u32 io_macro_config2;           /* 0x1c */
+       u32 io_macro_debug1;            /* 0x20 */
+       u32 reserved_2;                 /* 0x24 */
+       u32 emac_sys_low_power_dbg;     /* 0x28 */
+       u32 reserved_3[53];             /* upto 0x100 */
+};
+
+static struct dwmac_rgmii_regs emac_v2_3_0_por = {
+       .io_macro_config = 0x00C01343,
+       .sdcc_hc_dll_config = 0x2004642C,
+       .sdcc_hc_ddr_config = 0x00000000,
+       .sdcc_hc_dll_config2 = 0x00200000,
+       .sdcc_usr_ctl = 0x00010800,
+       .io_macro_config2 = 0x00002060
+};
+
+static void ethqos_set_func_clk_en(struct dwmac_rgmii_regs *regs)
+{
+       setbits_le32(&regs->io_macro_config, RGMII_CONFIG_FUNC_CLK_EN);
+}
+
+static int ethqos_dll_configure(struct udevice *dev,
+                               struct dwmac_rgmii_regs *regs)
+{
+       unsigned int val;
+       int retry = 1000;
+
+       /* Set CDR_EN */
+       setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CDR_EN);
+
+       /* Set CDR_EXT_EN */
+       setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CDR_EXT_EN);
+
+       /* Clear CK_OUT_EN */
+       clrbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CK_OUT_EN);
+
+       /* Set DLL_EN */
+       setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_EN);
+
+       clrbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_MCLK_GATING_EN);
+
+       clrbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CDR_FINE_PHASE);
+
+       /* Wait for CK_OUT_EN clear */
+       do {
+               val = readl(&regs->sdcc_hc_dll_config);
+               val &= SDCC_DLL_CONFIG_CK_OUT_EN;
+               if (!val)
+                       break;
+               mdelay(1);
+               retry--;
+       } while (retry > 0);
+       if (!retry)
+               dev_err(dev, "Clear CK_OUT_EN timedout\n");
+
+       /* Set CK_OUT_EN */
+       setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CK_OUT_EN);
+
+       /* Wait for CK_OUT_EN set */
+       retry = 1000;
+       do {
+               val = readl(&regs->sdcc_hc_dll_config);
+               val &= SDCC_DLL_CONFIG_CK_OUT_EN;
+               if (val)
+                       break;
+               mdelay(1);
+               retry--;
+       } while (retry > 0);
+       if (!retry)
+               dev_err(dev, "Set CK_OUT_EN timedout\n");
+
+       /* Set DDR_CAL_EN */
+       setbits_le32(&regs->sdcc_hc_dll_config2, SDCC_DLL_CONFIG2_DDR_CAL_EN);
+
+       clrbits_le32(&regs->sdcc_hc_dll_config2,
+                    SDCC_DLL_CONFIG2_DLL_CLOCK_DIS);
+
+       clrsetbits_le32(&regs->sdcc_hc_dll_config2,
+                       SDCC_DLL_CONFIG2_MCLK_FREQ_CALC, 0x1A << 10);
+
+       clrsetbits_le32(&regs->sdcc_hc_dll_config2,
+                       SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SEL, BIT(2));
+
+       setbits_le32(&regs->sdcc_hc_dll_config2,
+                    SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW);
+
+       return 0;
+}
+
+static int ethqos_rgmii_macro_init(struct udevice *dev,
+                                  struct dwmac_rgmii_regs *regs,
+                                  unsigned long speed)
+{
+       /* Disable loopback mode */
+       clrbits_le32(&regs->io_macro_config2,
+                    RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN);
+
+       /* Select RGMII, write 0 to interface select */
+       clrbits_le32(&regs->io_macro_config, RGMII_CONFIG_INTF_SEL);
+
+       switch (speed) {
+       case SPEED_1000:
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_DDR_MODE);
+               clrbits_le32(&regs->io_macro_config,
+                            RGMII_CONFIG_BYPASS_TX_ID_EN);
+               setbits_le32(&regs->io_macro_config,
+                            RGMII_CONFIG_POS_NEG_DATA_SEL);
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_PROG_SWAP);
+
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL);
+               setbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN);
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_RSVD_CONFIG15);
+               setbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_RX_PROG_SWAP);
+
+               /* Set PRG_RCLK_DLY to 57 for 1.8 ns delay */
+               clrsetbits_le32(&regs->sdcc_hc_ddr_config,
+                               SDCC_DDR_CONFIG_PRG_RCLK_DLY, 57);
+               setbits_le32(&regs->sdcc_hc_ddr_config, SDCC_DDR_CONFIG_PRG_DLY_EN);
+
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_LOOPBACK_EN);
+               break;
+
+       case SPEED_100:
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_DDR_MODE);
+               setbits_le32(&regs->io_macro_config,
+                            RGMII_CONFIG_BYPASS_TX_ID_EN);
+               clrbits_le32(&regs->io_macro_config,
+                            RGMII_CONFIG_POS_NEG_DATA_SEL);
+               clrbits_le32(&regs->io_macro_config, RGMII_CONFIG_PROG_SWAP);
+               clrsetbits_le32(&regs->io_macro_config,
+                               RGMII_CONFIG_MAX_SPD_PRG_2, BIT(6));
+
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL);
+               setbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN);
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_RSVD_CONFIG15);
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_RX_PROG_SWAP);
+
+               /* Write 0x5 to PRG_RCLK_DLY_CODE */
+               clrsetbits_le32(&regs->sdcc_hc_ddr_config,
+                               SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
+                               (BIT(29) | BIT(27)));
+               setbits_le32(&regs->sdcc_hc_ddr_config,
+                            SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY);
+               setbits_le32(&regs->sdcc_hc_ddr_config,
+                            SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN);
+
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_LOOPBACK_EN);
+               break;
+
+       case SPEED_10:
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_DDR_MODE);
+               setbits_le32(&regs->io_macro_config,
+                            RGMII_CONFIG_BYPASS_TX_ID_EN);
+               clrbits_le32(&regs->io_macro_config,
+                            RGMII_CONFIG_POS_NEG_DATA_SEL);
+               clrbits_le32(&regs->io_macro_config, RGMII_CONFIG_PROG_SWAP);
+               clrsetbits_le32(&regs->io_macro_config,
+                               RGMII_CONFIG_MAX_SPD_PRG_9,
+                               BIT(12) | GENMASK(9, 8));
+
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL);
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN);
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_RSVD_CONFIG15);
+               clrbits_le32(&regs->io_macro_config2,
+                            RGMII_CONFIG2_RX_PROG_SWAP);
+
+               /* Write 0x5 to PRG_RCLK_DLY_CODE */
+               clrsetbits_le32(&regs->sdcc_hc_ddr_config,
+                               SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
+                               (BIT(29) | BIT(27)));
+               setbits_le32(&regs->sdcc_hc_ddr_config,
+                            SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY);
+               setbits_le32(&regs->sdcc_hc_ddr_config,
+                            SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN);
+
+               setbits_le32(&regs->io_macro_config, RGMII_CONFIG_LOOPBACK_EN);
+               break;
+
+       default:
+               dev_err(dev, "Invalid speed %ld\n", speed);
+               return -EINVAL;
+       }
+
+       return 0;
+}
+
+static int ethqos_configure(struct udevice *dev,
+                           struct dwmac_rgmii_regs *regs,
+                           unsigned long speed)
+{
+       unsigned int retry = 1000;
+
+       /* Reset to POR values and enable clk */
+       writel(emac_v2_3_0_por.io_macro_config, &regs->io_macro_config);
+       writel(emac_v2_3_0_por.sdcc_hc_dll_config, &regs->sdcc_hc_dll_config);
+       writel(emac_v2_3_0_por.sdcc_hc_ddr_config, &regs->sdcc_hc_ddr_config);
+       writel(emac_v2_3_0_por.sdcc_hc_dll_config2, &regs->sdcc_hc_dll_config2);
+       writel(emac_v2_3_0_por.sdcc_usr_ctl, &regs->sdcc_usr_ctl);
+       writel(emac_v2_3_0_por.io_macro_config2, &regs->io_macro_config2);
+
+       ethqos_set_func_clk_en(regs);
+
+       /* Initialize the DLL first */
+
+       /* Set DLL_RST */
+       setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_RST);
+
+       /* Set PDN */
+       setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_PDN);
+
+       /* Clear DLL_RST */
+       clrbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_RST);
+
+       /* Clear PDN */
+       clrbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_PDN);
+
+       if (speed == SPEED_1000) {
+               /* Set DLL_EN */
+               setbits_le32(&regs->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_EN);
+
+               /* Set CK_OUT_EN */
+               setbits_le32(&regs->sdcc_hc_dll_config,
+                            SDCC_DLL_CONFIG_CK_OUT_EN);
+
+               /* Set USR_CTL bit 26 with mask of 3 bits */
+               clrsetbits_le32(&regs->sdcc_usr_ctl, GENMASK(26, 24), BIT(26));
+
+               /* wait for DLL LOCK */
+               do {
+                       mdelay(1);
+                       if (readl(&regs->sdc4_status) & SDC4_STATUS_DLL_LOCK)
+                               break;
+                       retry--;
+               } while (retry > 0);
+               if (!retry)
+                       dev_err(dev, "Timeout while waiting for DLL lock\n");
+
+               ethqos_dll_configure(dev, regs);
+       }
+
+       ethqos_rgmii_macro_init(dev, regs, speed);
+
+       return 0;
+}
+
+static void ethqos_rgmii_dump(struct udevice *dev,
+                             struct dwmac_rgmii_regs *regs)
+{
+       dev_dbg(dev, "Rgmii register dump\n");
+       dev_dbg(dev, "RGMII_IO_MACRO_CONFIG: %08x\n",
+               readl(&regs->io_macro_config));
+       dev_dbg(dev, "SDCC_HC_REG_DLL_CONFIG: %08x\n",
+               readl(&regs->sdcc_hc_dll_config));
+       dev_dbg(dev, "SDCC_HC_REG_DDR_CONFIG: %08x\n",
+               readl(&regs->sdcc_hc_ddr_config));
+       dev_dbg(dev, "SDCC_HC_REG_DLL_CONFIG2: %08x\n",
+               readl(&regs->sdcc_hc_dll_config2));
+       dev_dbg(dev, "SDC4_STATUS: %08x\n",
+               readl(&regs->sdc4_status));
+       dev_dbg(dev, "SDCC_USR_CTL: %08x\n",
+               readl(&regs->sdcc_usr_ctl));
+       dev_dbg(dev, "RGMII_IO_MACRO_CONFIG2: %08x\n",
+               readl(&regs->io_macro_config2));
+       dev_dbg(dev, "RGMII_IO_MACRO_DEBUG1: %08x\n",
+               readl(&regs->io_macro_debug1));
+       dev_dbg(dev, "EMAC_SYSTEM_LOW_POWER_DEBUG: %08x\n",
+               readl(&regs->emac_sys_low_power_dbg));
+}
+
+static int qcom_eqos_rgmii_set_speed(struct udevice *dev,
+                                    void *rgmii_regs,
+                                    unsigned long speed)
+{
+       int ret;
+
+       ethqos_rgmii_dump(dev, rgmii_regs);
+
+       ret = ethqos_configure(dev, rgmii_regs, speed);
+       if (ret)
+               return ret;
+
+       ethqos_rgmii_dump(dev, rgmii_regs);
+
+       return 0;
+}
+
+static int qcom_eqos_rgmii_reset(struct udevice *dev, void *rgmii_regs)
+{
+       ethqos_set_func_clk_en(rgmii_regs);
+
+       return 0;
+}
+
+static int eqos_start_clks_qcom(struct udevice *dev)
+{
+       if (IS_ENABLED(CONFIG_CLK)) {
+               struct clk_bulk clocks;
+               int ret;
+
+               ret = clk_get_bulk(dev, &clocks);
+               if (ret)
+                       return ret;
+
+               ret = clk_enable_bulk(&clocks);
+               if (ret)
+                       return ret;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static int eqos_stop_clks_qcom(struct udevice *dev)
+{
+       if (IS_ENABLED(CONFIG_CLK)) {
+               struct clk_bulk clocks;
+               int ret;
+
+               ret = clk_get_bulk(dev, &clocks);
+               if (ret)
+                       return ret;
+
+               ret = clk_disable_bulk(&clocks);
+               if (ret)
+                       return ret;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static int eqos_start_resets_qcom(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       if (!eqos->phy) {
+               ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 0);
+               if (ret < 0) {
+                       pr_err("dm_gpio_set_value(phy_reset, assert) failed: %d", ret);
+                       return ret;
+               }
+
+               udelay(eqos->reset_delays[0]);
+
+               ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 1);
+               if (ret < 0) {
+                       pr_err("dm_gpio_set_value(phy_reset, deassert) failed: %d", ret);
+                       return ret;
+               }
+
+               udelay(eqos->reset_delays[1]);
+
+               ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 0);
+               if (ret < 0) {
+                       pr_err("dm_gpio_set_value(phy_reset, deassert) failed: %d", ret);
+                       return ret;
+               }
+
+               udelay(eqos->reset_delays[2]);
+       }
+
+       ret = reset_deassert(&eqos->reset_ctl);
+       if (ret < 0) {
+               pr_err("reset_deassert() failed: %d", ret);
+               return ret;
+       }
+
+       ret = qcom_eqos_rgmii_reset(dev, eqos->eqos_qcom_rgmii_regs);
+       if (ret < 0) {
+               pr_err("qcom rgmii_reset failed: %d", ret);
+               return ret;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+/* Clock rates */
+#define RGMII_1000_NOM_CLK_FREQ                        (250 * 1000 * 1000UL)
+#define RGMII_ID_MODE_100_LOW_SVS_CLK_FREQ      (50 * 1000 * 1000UL)
+#define RGMII_ID_MODE_10_LOW_SVS_CLK_FREQ        (5 * 1000 * 1000UL)
+
+static int eqos_set_tx_clk_speed_qcom(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       ulong rate;
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       switch (eqos->phy->speed) {
+       case SPEED_1000:
+               rate = RGMII_1000_NOM_CLK_FREQ;
+               break;
+       case SPEED_100:
+               rate = RGMII_ID_MODE_100_LOW_SVS_CLK_FREQ;
+               break;
+       case SPEED_10:
+               rate = RGMII_ID_MODE_10_LOW_SVS_CLK_FREQ;
+               break;
+       default:
+               pr_err("invalid speed %d", eqos->phy->speed);
+               return -EINVAL;
+       }
+
+       ret = clk_set_rate(&eqos->clk_tx, rate);
+       if (ret < 0) {
+               pr_err("clk_set_rate(tx_clk, %lu) failed: %d", rate, ret);
+               return ret;
+       }
+
+       ret = qcom_eqos_rgmii_set_speed(dev, eqos->eqos_qcom_rgmii_regs,
+                                       eqos->phy->speed);
+       if (ret < 0) {
+               pr_err("qcom set_speed: %d, failed: %d", eqos->phy->speed, ret);
+               return ret;
+       }
+
+       return 0;
+}
+
+static int eqos_probe_resources_qcom(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+       phy_interface_t interface;
+       int reset_flags = GPIOD_IS_OUT;
+       int ret;
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       interface = eqos->config->interface(dev);
+
+       if (interface == PHY_INTERFACE_MODE_NA) {
+               pr_err("Invalid PHY interface\n");
+               return -EINVAL;
+       }
+
+       eqos->max_speed = dev_read_u32_default(dev, "max-speed", 0);
+
+       eqos->tx_fifo_sz = dev_read_u32_default(dev, "tx-fifo-depth", 0);
+       eqos->rx_fifo_sz = dev_read_u32_default(dev, "rx-fifo-depth", 0);
+
+       ret = reset_get_by_name(dev, "emac", &eqos->reset_ctl);
+       if (ret) {
+               pr_err("reset_get_by_name(rst) failed: %d", ret);
+               return ret;
+       }
+
+       if (dev_read_bool(dev, "snps,reset-active-low"))
+               reset_flags |= GPIOD_ACTIVE_LOW;
+
+       ret = gpio_request_by_name(dev, "snps,reset-gpio", 0,
+                                  &eqos->phy_reset_gpio, reset_flags);
+       if (ret == 0) {
+               ret = dev_read_u32_array(dev, "snps,reset-delays-us",
+                                        eqos->reset_delays, 3);
+       } else if (ret == -ENOENT) {
+               ret = 0;
+       }
+
+       eqos->eqos_qcom_rgmii_regs = (void *)dev_read_addr_name(dev, "rgmii");
+       if ((fdt_addr_t)eqos->eqos_qcom_rgmii_regs == FDT_ADDR_T_NONE) {
+               pr_err("Invalid RGMII address\n");
+               return -EINVAL;
+       }
+
+       ret = clk_get_by_name(dev, "rgmii", &eqos->clk_tx);
+       if (ret) {
+               pr_err("clk_get_by_name(tx) failed: %d", ret);
+               return -EINVAL;
+       }
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static int eqos_remove_resources_qcom(struct udevice *dev)
+{
+       struct eqos_priv *eqos = dev_get_priv(dev);
+
+       debug("%s(dev=%p):\n", __func__, dev);
+
+       clk_free(&eqos->clk_tx);
+       dm_gpio_free(dev, &eqos->phy_reset_gpio);
+       reset_free(&eqos->reset_ctl);
+
+       debug("%s: OK\n", __func__);
+       return 0;
+}
+
+static struct eqos_ops eqos_qcom_ops = {
+       .eqos_inval_desc = eqos_inval_desc_generic,
+       .eqos_flush_desc = eqos_flush_desc_generic,
+       .eqos_inval_buffer = eqos_inval_buffer_generic,
+       .eqos_flush_buffer = eqos_flush_buffer_generic,
+       .eqos_probe_resources = eqos_probe_resources_qcom,
+       .eqos_remove_resources = eqos_remove_resources_qcom,
+       .eqos_stop_resets = eqos_null_ops,
+       .eqos_start_resets = eqos_start_resets_qcom,
+       .eqos_stop_clks = eqos_stop_clks_qcom,
+       .eqos_start_clks = eqos_start_clks_qcom,
+       .eqos_calibrate_pads = eqos_null_ops,
+       .eqos_disable_calibration = eqos_null_ops,
+       .eqos_set_tx_clk_speed = eqos_set_tx_clk_speed_qcom,
+       .eqos_get_enetaddr = eqos_null_ops,
+};
+
+struct eqos_config __maybe_unused eqos_qcom_config = {
+       .reg_access_always_ok = false,
+       .mdio_wait = 10,
+       .swr_wait = 50,
+       .config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB,
+       .config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_250_300,
+       .axi_bus_width = EQOS_AXI_WIDTH_64,
+       .interface = dev_read_phy_mode,
+       .ops = &eqos_qcom_ops
+};