IMX_FEC_BASE is not used in these boards, so drop it.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0
#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
/* Ethernet */
#define CONFIG_FEC_MXC_PHYADDR 0
-#define IMX_FEC_BASE ENET_BASE_ADDR
/* USB */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define PHYS_SDRAM_SIZE SZ_1G
/* ENET1 */
-#define IMX_FEC_BASE ENET2_BASE_ADDR
/* MMC Config */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_BOOTCOUNT_BE
/* FEC ethernet */
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 7
/* MMC Configs */
#ifdef CONFIG_CMD_NET
#define CONFIG_FEC_ENET_DEV 0
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
#endif
* Ethernet on SOC (FEC)
*/
#ifdef CONFIG_CMD_NET
-#define IMX_FEC_BASE FEC_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
#endif
#define CONFIG_SYS_FLASH_BANKS_SIZES { (32 * SZ_1M) }
/* Ethernet Configuration */
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 1
#define CONFIG_EXTRA_ENV_SETTINGS \
/* Network */
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#ifdef CONFIG_CMD_USB
#define CONFIG_FEC_ENET_DEV 1
#if (CONFIG_FEC_ENET_DEV == 0)
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x2
#elif (CONFIG_FEC_ENET_DEV == 1)
-#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#endif
#endif
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#ifdef CONFIG_CMD_NET
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#endif
/* Environment organization */
/* Ethernet Configuration */
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 1
/* Framebuffer */
/* Network support */
-#define IMX_FEC_BASE ENET2_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#define CONFIG_MXC_UART_BASE UART6_BASE_ADDR
#endif
#ifdef CONFIG_CMD_NET
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x1
#endif
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
-#define IMX_FEC_BASE ENET_BASE_ADDR
#if defined(CONFIG_TQMA6X_MMC_BOOT)
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_FSL_ESDHC_NUM 1
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0
/* I2C Configs */
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
/* Network */
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_FEC_ENET_DEV 0
-#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR 0x0
#define CONFIG_UBOOT_SECTOR_START 0x2