--- /dev/null
+.. SPDX-License-Identifier: GPL-2.0
+
+====================================================================
+Notes on Oxford Semiconductor PCIe (Tornado) 950 serial port devices
+====================================================================
+
+Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
+by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
+
+The baud rate produced by the baud generator is obtained from this input
+frequency by dividing it by the clock prescaler, which can be set to any
+value from 1 to 63.875 in increments of 0.125, and then the usual 16-bit
+divisor is used as with the original 8250, to divide the frequency by a
+value from 1 to 65535. Finally a programmable oversampling rate is used
+that can take any value from 4 to 16 to divide the frequency further and
+determine the actual baud rate used. Baud rates from 15625000bps down
+to 0.933bps can be obtained this way.
+
+By default the oversampling rate is set to 16 and the clock prescaler is
+set to 33.875, meaning that the frequency to be used as the reference
+for the usual 16-bit divisor is 115313.653, which is close enough to the
+frequency of 115200 used by the original 8250 for the same values to be
+used for the divisor to obtain the requested baud rates by software that
+is unaware of the extra clock controls available.
+
+The oversampling rate is programmed with the TCR register and the clock
+prescaler is programmed with the CPR/CPR2 register pair[1][2][3][4].
+To switch away from the default value of 33.875 for the prescaler the
+the enhanced mode has to be explicitly enabled though, by setting bit 4
+of the EFR. In that mode setting bit 7 in the MCR enables the prescaler
+or otherwise it is bypassed as if the value of 1 was used. Additionally
+writing any value to CPR clears CPR2 for compatibility with old software
+written for older conventional PCI Oxford Semiconductor devices that do
+not have the extra prescaler's 9th bit in CPR2, so the CPR/CPR2 register
+pair has to be programmed in the right order.
+
+By using these parameters rates from 15625000bps down to 1bps can be
+obtained, with either exact or highly-accurate actual bit rates for
+standard and many non-standard rates.
+
+Here are the figures for the standard and some non-standard baud rates
+(including those quoted in Oxford Semiconductor documentation), giving
+the requested rate (r), the actual rate yielded (a) and its deviation
+from the requested rate (d), and the values of the oversampling rate
+(tcr), the clock prescaler (cpr) and the divisor (div) produced by the
+new `get_divisor' handler:
+
+r: 15625000, a: 15625000.00, d: 0.0000%, tcr: 4, cpr: 1.000, div: 1
+r: 12500000, a: 12500000.00, d: 0.0000%, tcr: 5, cpr: 1.000, div: 1
+r: 10416666, a: 10416666.67, d: 0.0000%, tcr: 6, cpr: 1.000, div: 1
+r: 8928571, a: 8928571.43, d: 0.0000%, tcr: 7, cpr: 1.000, div: 1
+r: 7812500, a: 7812500.00, d: 0.0000%, tcr: 8, cpr: 1.000, div: 1
+r: 4000000, a: 4000000.00, d: 0.0000%, tcr: 5, cpr: 3.125, div: 1
+r: 3686400, a: 3676470.59, d: -0.2694%, tcr: 8, cpr: 2.125, div: 1
+r: 3500000, a: 3496503.50, d: -0.0999%, tcr: 13, cpr: 1.375, div: 1
+r: 3000000, a: 2976190.48, d: -0.7937%, tcr: 14, cpr: 1.500, div: 1
+r: 2500000, a: 2500000.00, d: 0.0000%, tcr: 10, cpr: 2.500, div: 1
+r: 2000000, a: 2000000.00, d: 0.0000%, tcr: 10, cpr: 3.125, div: 1
+r: 1843200, a: 1838235.29, d: -0.2694%, tcr: 16, cpr: 2.125, div: 1
+r: 1500000, a: 1492537.31, d: -0.4975%, tcr: 5, cpr: 8.375, div: 1
+r: 1152000, a: 1152073.73, d: 0.0064%, tcr: 14, cpr: 3.875, div: 1
+r: 921600, a: 919117.65, d: -0.2694%, tcr: 16, cpr: 2.125, div: 2
+r: 576000, a: 576036.87, d: 0.0064%, tcr: 14, cpr: 3.875, div: 2
+r: 460800, a: 460829.49, d: 0.0064%, tcr: 7, cpr: 3.875, div: 5
+r: 230400, a: 230414.75, d: 0.0064%, tcr: 14, cpr: 3.875, div: 5
+r: 115200, a: 115207.37, d: 0.0064%, tcr: 14, cpr: 1.250, div: 31
+r: 57600, a: 57603.69, d: 0.0064%, tcr: 8, cpr: 3.875, div: 35
+r: 38400, a: 38402.46, d: 0.0064%, tcr: 14, cpr: 3.875, div: 30
+r: 19200, a: 19201.23, d: 0.0064%, tcr: 8, cpr: 3.875, div: 105
+r: 9600, a: 9600.06, d: 0.0006%, tcr: 9, cpr: 1.125, div: 643
+r: 4800, a: 4799.98, d: -0.0004%, tcr: 7, cpr: 2.875, div: 647
+r: 2400, a: 2400.02, d: 0.0008%, tcr: 9, cpr: 2.250, div: 1286
+r: 1200, a: 1200.00, d: 0.0000%, tcr: 14, cpr: 2.875, div: 1294
+r: 300, a: 300.00, d: 0.0000%, tcr: 11, cpr: 2.625, div: 7215
+r: 200, a: 200.00, d: 0.0000%, tcr: 16, cpr: 1.250, div: 15625
+r: 150, a: 150.00, d: 0.0000%, tcr: 13, cpr: 2.250, div: 14245
+r: 134, a: 134.00, d: 0.0000%, tcr: 11, cpr: 2.625, div: 16153
+r: 110, a: 110.00, d: 0.0000%, tcr: 12, cpr: 1.000, div: 47348
+r: 75, a: 75.00, d: 0.0000%, tcr: 4, cpr: 5.875, div: 35461
+r: 50, a: 50.00, d: 0.0000%, tcr: 16, cpr: 1.250, div: 62500
+r: 25, a: 25.00, d: 0.0000%, tcr: 16, cpr: 2.500, div: 62500
+r: 4, a: 4.00, d: 0.0000%, tcr: 16, cpr: 20.000, div: 48828
+r: 2, a: 2.00, d: 0.0000%, tcr: 16, cpr: 40.000, div: 48828
+r: 1, a: 1.00, d: 0.0000%, tcr: 16, cpr: 63.875, div: 61154
+
+With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
+limitation imposed by `serial8250_get_baud_rate' standard baud rates
+below 300bps become unavailable in the regular way, e.g. the rate of
+200bps requires the baud base to be divided by 78125 and that is beyond
+the unsigned 16-bit range. The historic spd_cust feature can still be
+used by encoding the values for, the prescaler, the oversampling rate
+and the clock divisor (DLM/DLL) as follows to obtain such rates if so
+required:
+
+ 31 29 28 20 19 16 15 0
++-----+-----------------+-------+-------------------------------+
+|0 0 0| CPR2:CPR | TCR | DLM:DLL |
++-----+-----------------+-------+-------------------------------+
+
+Use a value such encoded for the `custom_divisor' field along with the
+ASYNC_SPD_CUST flag set in the `flags' field in `struct serial_struct'
+passed with the TIOCSSERIAL ioctl(2), such as with the setserial(8)
+utility and its `divisor' and `spd_cust' parameters, and the select
+the baud rate of 38400bps. Note that the value of 0 in TCR sets the
+oversampling rate to 16 and prescaler values below 1 in CPR2/CPR are
+clamped by the driver to 1.
+
+For example the value of 0x1f4004e2 will set CPR2/CPR, TCR and DLM/DLL
+respectively to 0x1f4, 0x0 and 0x04e2, choosing the prescaler value,
+the oversampling rate and the clock divisor of 62.500, 16 and 1250
+respectively. These parameters will set the baud rate for the serial
+port to 62500000 / 62.500 / 1250 / 16 = 50bps.
+
+References:
+
+[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
+ Inc., DS-0045, 10 Nov 2008, Section "950 Mode", pp. 64-65
+
+[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
+ Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "950 Mode",
+ p. 20
+
+[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
+ Semiconductor, Inc., DS-0047, Feb 08, Section "950 Mode", p. 20
+
+[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
+ Semiconductor, Inc., DS-0048, Feb 08, Section "950 Mode", p. 20
+
+Maciej W. Rozycki <macro@orcam.me.uk>
#include <linux/pci.h>
#include <linux/string.h>
#include <linux/kernel.h>
+#include <linux/math.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/tty.h>
return number_uarts;
}
+/* Tornado-specific constants for the TCR and CPR registers; see below. */
+#define OXSEMI_TORNADO_TCR_MASK 0xf
+#define OXSEMI_TORNADO_CPR_MASK 0x1ff
+#define OXSEMI_TORNADO_CPR_MIN 0x008
+#define OXSEMI_TORNADO_CPR_DEF 0x10f
+
+/*
+ * Determine the oversampling rate, the clock prescaler, and the clock
+ * divisor for the requested baud rate. The clock rate is 62.5 MHz,
+ * which is four times the baud base, and the prescaler increments in
+ * steps of 1/8. Therefore to make calculations on integers we need
+ * to use a scaled clock rate, which is the baud base multiplied by 32
+ * (or our assumed UART clock rate multiplied by 2).
+ *
+ * The allowed oversampling rates are from 4 up to 16 inclusive (values
+ * from 0 to 3 inclusive map to 16). Likewise the clock prescaler allows
+ * values between 1.000 and 63.875 inclusive (operation for values from
+ * 0.000 to 0.875 has not been specified). The clock divisor is the usual
+ * unsigned 16-bit integer.
+ *
+ * For the most accurate baud rate we use a table of predetermined
+ * oversampling rates and clock prescalers that records all possible
+ * products of the two parameters in the range from 4 up to 255 inclusive,
+ * and additionally 335 for the 1500000bps rate, with the prescaler scaled
+ * by 8. The table is sorted by the decreasing value of the oversampling
+ * rate and ties are resolved by sorting by the decreasing value of the
+ * product. This way preference is given to higher oversampling rates.
+ *
+ * We iterate over the table and choose the product of an oversampling
+ * rate and a clock prescaler that gives the lowest integer division
+ * result deviation, or if an exact integer divider is found we stop
+ * looking for it right away. We do some fixup if the resulting clock
+ * divisor required would be out of its unsigned 16-bit integer range.
+ *
+ * Finally we abuse the supposed fractional part returned to encode the
+ * 4-bit value of the oversampling rate and the 9-bit value of the clock
+ * prescaler which will end up in the TCR and CPR/CPR2 registers.
+ */
+static unsigned int pci_oxsemi_tornado_get_divisor(struct uart_port *port,
+ unsigned int baud,
+ unsigned int *frac)
+{
+ static u8 p[][2] = {
+ { 16, 14, }, { 16, 13, }, { 16, 12, }, { 16, 11, },
+ { 16, 10, }, { 16, 9, }, { 16, 8, }, { 15, 17, },
+ { 15, 16, }, { 15, 15, }, { 15, 14, }, { 15, 13, },
+ { 15, 12, }, { 15, 11, }, { 15, 10, }, { 15, 9, },
+ { 15, 8, }, { 14, 18, }, { 14, 17, }, { 14, 14, },
+ { 14, 13, }, { 14, 12, }, { 14, 11, }, { 14, 10, },
+ { 14, 9, }, { 14, 8, }, { 13, 19, }, { 13, 18, },
+ { 13, 17, }, { 13, 13, }, { 13, 12, }, { 13, 11, },
+ { 13, 10, }, { 13, 9, }, { 13, 8, }, { 12, 19, },
+ { 12, 18, }, { 12, 17, }, { 12, 11, }, { 12, 9, },
+ { 12, 8, }, { 11, 23, }, { 11, 22, }, { 11, 21, },
+ { 11, 20, }, { 11, 19, }, { 11, 18, }, { 11, 17, },
+ { 11, 11, }, { 11, 10, }, { 11, 9, }, { 11, 8, },
+ { 10, 25, }, { 10, 23, }, { 10, 20, }, { 10, 19, },
+ { 10, 17, }, { 10, 10, }, { 10, 9, }, { 10, 8, },
+ { 9, 27, }, { 9, 23, }, { 9, 21, }, { 9, 19, },
+ { 9, 18, }, { 9, 17, }, { 9, 9, }, { 9, 8, },
+ { 8, 31, }, { 8, 29, }, { 8, 23, }, { 8, 19, },
+ { 8, 17, }, { 8, 8, }, { 7, 35, }, { 7, 31, },
+ { 7, 29, }, { 7, 25, }, { 7, 23, }, { 7, 21, },
+ { 7, 19, }, { 7, 17, }, { 7, 15, }, { 7, 14, },
+ { 7, 13, }, { 7, 12, }, { 7, 11, }, { 7, 10, },
+ { 7, 9, }, { 7, 8, }, { 6, 41, }, { 6, 37, },
+ { 6, 31, }, { 6, 29, }, { 6, 23, }, { 6, 19, },
+ { 6, 17, }, { 6, 13, }, { 6, 11, }, { 6, 10, },
+ { 6, 9, }, { 6, 8, }, { 5, 67, }, { 5, 47, },
+ { 5, 43, }, { 5, 41, }, { 5, 37, }, { 5, 31, },
+ { 5, 29, }, { 5, 25, }, { 5, 23, }, { 5, 19, },
+ { 5, 17, }, { 5, 15, }, { 5, 13, }, { 5, 11, },
+ { 5, 10, }, { 5, 9, }, { 5, 8, }, { 4, 61, },
+ { 4, 59, }, { 4, 53, }, { 4, 47, }, { 4, 43, },
+ { 4, 41, }, { 4, 37, }, { 4, 31, }, { 4, 29, },
+ { 4, 23, }, { 4, 19, }, { 4, 17, }, { 4, 13, },
+ { 4, 9, }, { 4, 8, },
+ };
+ /* Scale the quotient for comparison to get the fractional part. */
+ const unsigned int quot_scale = 65536;
+ unsigned int sclk = port->uartclk * 2;
+ unsigned int sdiv = DIV_ROUND_CLOSEST(sclk, baud);
+ unsigned int best_squot;
+ unsigned int squot;
+ unsigned int quot;
+ u16 cpr;
+ u8 tcr;
+ int i;
+
+ /* Old custom speed handling. */
+ if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST) {
+ unsigned int cust_div = port->custom_divisor;
+
+ quot = cust_div & UART_DIV_MAX;
+ tcr = (cust_div >> 16) & OXSEMI_TORNADO_TCR_MASK;
+ cpr = (cust_div >> 20) & OXSEMI_TORNADO_CPR_MASK;
+ if (cpr < OXSEMI_TORNADO_CPR_MIN)
+ cpr = OXSEMI_TORNADO_CPR_DEF;
+ } else {
+ best_squot = quot_scale;
+ for (i = 0; i < ARRAY_SIZE(p); i++) {
+ unsigned int spre;
+ unsigned int srem;
+ u8 cp;
+ u8 tc;
+
+ tc = p[i][0];
+ cp = p[i][1];
+ spre = tc * cp;
+
+ srem = sdiv % spre;
+ if (srem > spre / 2)
+ srem = spre - srem;
+ squot = DIV_ROUND_CLOSEST(srem * quot_scale, spre);
+
+ if (srem == 0) {
+ tcr = tc;
+ cpr = cp;
+ quot = sdiv / spre;
+ break;
+ } else if (squot < best_squot) {
+ best_squot = squot;
+ tcr = tc;
+ cpr = cp;
+ quot = DIV_ROUND_CLOSEST(sdiv, spre);
+ }
+ }
+ while (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1 &&
+ quot % 2 == 0) {
+ quot >>= 1;
+ tcr <<= 1;
+ }
+ while (quot > UART_DIV_MAX) {
+ if (tcr <= (OXSEMI_TORNADO_TCR_MASK + 1) >> 1) {
+ quot >>= 1;
+ tcr <<= 1;
+ } else if (cpr <= OXSEMI_TORNADO_CPR_MASK >> 1) {
+ quot >>= 1;
+ cpr <<= 1;
+ } else {
+ quot = quot * cpr / OXSEMI_TORNADO_CPR_MASK;
+ cpr = OXSEMI_TORNADO_CPR_MASK;
+ }
+ }
+ }
+
+ *frac = (cpr << 8) | (tcr & OXSEMI_TORNADO_TCR_MASK);
+ return quot;
+}
+
+/*
+ * Set the oversampling rate in the transmitter clock cycle register (TCR),
+ * the clock prescaler in the clock prescaler register (CPR and CPR2), and
+ * the clock divisor in the divisor latch (DLL and DLM). Note that for
+ * backwards compatibility any write to CPR clears CPR2 and therefore CPR
+ * has to be written first, followed by CPR2, which occupies the location
+ * of CKS used with earlier UART designs.
+ */
+static void pci_oxsemi_tornado_set_divisor(struct uart_port *port,
+ unsigned int baud,
+ unsigned int quot,
+ unsigned int quot_frac)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ u8 cpr2 = quot_frac >> 16;
+ u8 cpr = quot_frac >> 8;
+ u8 tcr = quot_frac;
+
+ serial_icr_write(up, UART_TCR, tcr);
+ serial_icr_write(up, UART_CPR, cpr);
+ serial_icr_write(up, UART_CKS, cpr2);
+ serial8250_do_set_divisor(port, baud, quot, 0);
+}
+
+/*
+ * For Tornado devices we force MCR[7] set for the Divide-by-M N/8 baud rate
+ * generator prescaler (CPR and CPR2). Otherwise no prescaler would be used.
+ */
+static void pci_oxsemi_tornado_set_mctrl(struct uart_port *port,
+ unsigned int mctrl)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ up->mcr |= UART_MCR_CLKSEL;
+ serial8250_do_set_mctrl(port, mctrl);
+}
+
+static int pci_oxsemi_tornado_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *up, int idx)
+{
+ struct pci_dev *dev = priv->dev;
+
+ if (pci_oxsemi_tornado_p(dev)) {
+ up->port.get_divisor = pci_oxsemi_tornado_get_divisor;
+ up->port.set_divisor = pci_oxsemi_tornado_set_divisor;
+ up->port.set_mctrl = pci_oxsemi_tornado_set_mctrl;
+ }
+
+ return pci_default_setup(priv, board, up, idx);
+}
+
static int pci_asix_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_oxsemi_tornado_init,
- .setup = pci_default_setup,
+ .setup = pci_oxsemi_tornado_setup,
},
{
.vendor = PCI_VENDOR_ID_MAINPINE,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.init = pci_oxsemi_tornado_init,
- .setup = pci_default_setup,
+ .setup = pci_oxsemi_tornado_setup,
},
{
.vendor = PCI_VENDOR_ID_DIGI,
.subvendor = PCI_SUBVENDOR_ID_IBM,
.subdevice = PCI_ANY_ID,
.init = pci_oxsemi_tornado_init,
- .setup = pci_default_setup,
+ .setup = pci_oxsemi_tornado_setup,
},
{
.vendor = PCI_VENDOR_ID_INTEL,
pbn_b0_2_1843200,
pbn_b0_4_1843200,
- pbn_b0_1_3906250,
+ pbn_b0_1_15625000,
pbn_b0_bt_1_115200,
pbn_b0_bt_2_115200,
pbn_panacom4,
pbn_plx_romulus,
pbn_oxsemi,
- pbn_oxsemi_1_3906250,
- pbn_oxsemi_2_3906250,
- pbn_oxsemi_4_3906250,
- pbn_oxsemi_8_3906250,
+ pbn_oxsemi_1_15625000,
+ pbn_oxsemi_2_15625000,
+ pbn_oxsemi_4_15625000,
+ pbn_oxsemi_8_15625000,
pbn_intel_i960,
pbn_sgi_ioc3,
pbn_computone_4,
.uart_offset = 8,
},
- [pbn_b0_1_3906250] = {
+ [pbn_b0_1_15625000] = {
.flags = FL_BASE0,
.num_ports = 1,
- .base_baud = 3906250,
+ .base_baud = 15625000,
.uart_offset = 8,
},
.base_baud = 115200,
.uart_offset = 8,
},
- [pbn_oxsemi_1_3906250] = {
+ [pbn_oxsemi_1_15625000] = {
.flags = FL_BASE0,
.num_ports = 1,
- .base_baud = 3906250,
+ .base_baud = 15625000,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
- [pbn_oxsemi_2_3906250] = {
+ [pbn_oxsemi_2_15625000] = {
.flags = FL_BASE0,
.num_ports = 2,
- .base_baud = 3906250,
+ .base_baud = 15625000,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
- [pbn_oxsemi_4_3906250] = {
+ [pbn_oxsemi_4_15625000] = {
.flags = FL_BASE0,
.num_ports = 4,
- .base_baud = 3906250,
+ .base_baud = 15625000,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
- [pbn_oxsemi_8_3906250] = {
+ [pbn_oxsemi_8_15625000] = {
.flags = FL_BASE0,
.num_ports = 8,
- .base_baud = 3906250,
+ .base_baud = 15625000,
.uart_offset = 0x200,
.first_offset = 0x1000,
},
*/
{ PCI_VENDOR_ID_OXSEMI, 0xc101, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc105, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc11b, /* OXPCIe952 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc11f, /* OXPCIe952 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc120, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc124, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc138, /* OXPCIe952 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc13d, /* OXPCIe952 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc140, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc141, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc144, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc145, /* OXPCIe952 1 Legacy UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_b0_1_3906250 },
+ pbn_b0_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc158, /* OXPCIe952 2 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_2_3906250 },
+ pbn_oxsemi_2_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc15d, /* OXPCIe952 2 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_2_3906250 },
+ pbn_oxsemi_2_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc208, /* OXPCIe954 4 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_4_3906250 },
+ pbn_oxsemi_4_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc20d, /* OXPCIe954 4 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_4_3906250 },
+ pbn_oxsemi_4_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc308, /* OXPCIe958 8 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_8_3906250 },
+ pbn_oxsemi_8_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc30d, /* OXPCIe958 8 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_8_3906250 },
+ pbn_oxsemi_8_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc40b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc40f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc41b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc41f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc42b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc42f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc43b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc43f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc44b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc44f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc45b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc45f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc46b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc46f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc47b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc47f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc48b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc48f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc49b, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc49f, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc4ab, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc4af, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc4bb, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc4bf, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc4cb, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_OXSEMI, 0xc4cf, /* OXPCIe200 1 Native UART */
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
/*
* Mainpine Inc. IQ Express "Rev3" utilizing OxSemi Tornado
*/
{ PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 1 Port V.34 Super-G3 Fax */
PCI_VENDOR_ID_MAINPINE, 0x4001, 0, 0,
- pbn_oxsemi_1_3906250 },
+ pbn_oxsemi_1_15625000 },
{ PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 2 Port V.34 Super-G3 Fax */
PCI_VENDOR_ID_MAINPINE, 0x4002, 0, 0,
- pbn_oxsemi_2_3906250 },
+ pbn_oxsemi_2_15625000 },
{ PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 4 Port V.34 Super-G3 Fax */
PCI_VENDOR_ID_MAINPINE, 0x4004, 0, 0,
- pbn_oxsemi_4_3906250 },
+ pbn_oxsemi_4_15625000 },
{ PCI_VENDOR_ID_MAINPINE, 0x4000, /* IQ Express 8 Port V.34 Super-G3 Fax */
PCI_VENDOR_ID_MAINPINE, 0x4008, 0, 0,
- pbn_oxsemi_8_3906250 },
+ pbn_oxsemi_8_15625000 },
/*
* Digi/IBM PCIe 2-port Async EIA-232 Adapter utilizing OxSemi Tornado
*/
{ PCI_VENDOR_ID_DIGI, PCIE_DEVICE_ID_NEO_2_OX_IBM,
PCI_SUBVENDOR_ID_IBM, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_2_3906250 },
+ pbn_oxsemi_2_15625000 },
/*
* EndRun Technologies. PCI express device range.
* EndRun PTP/1588 has 2 Native UARTs utilizing OxSemi 952.
*/
{ PCI_VENDOR_ID_ENDRUN, PCI_DEVICE_ID_ENDRUN_1588,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
- pbn_oxsemi_2_3906250 },
+ pbn_oxsemi_2_15625000 },
/*
* SBS Technologies, Inc. P-Octal and PMC-OCTPRO cards,
projects / kernel.git / commitdiff