This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
prompt "Target select"
optional
-config TARGET_MPC8308_P1M
- bool "Support mpc8308_p1m"
- select ARCH_MPC8308
-
config TARGET_VE8313
bool "Support ve8313"
select ARCH_MPC8313
source "board/freescale/mpc837xerdb/Kconfig"
source "board/ids/ids8313/Kconfig"
source "board/keymile/Kconfig"
-source "board/mpc8308_p1m/Kconfig"
source "board/tqc/tqm834x/Kconfig"
source "board/ve8313/Kconfig"
source "board/gdsys/mpc8308/Kconfig"
+++ /dev/null
-if TARGET_MPC8308_P1M
-
-config SYS_BOARD
- default "mpc8308_p1m"
-
-config SYS_CONFIG_NAME
- default "mpc8308_p1m"
-
-endif
+++ /dev/null
-MPC8308_P1M BOARD
-M: Ilya Yanok <yanok@emcraft.com>
-S: Maintained
-F: board/mpc8308_p1m/
-F: include/configs/mpc8308_p1m.h
-F: configs/mpc8308_p1m_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-# (C) Copyright 2010
-# Ilya Yanok, Emcraft Systems, yanok@emcraft.com
-
-obj-y := mpc8308_p1m.o sdram.o
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <init.h>
-#include <net.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <pci.h>
-#include <mpc83xx.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_mpc83xx_serdes.h>
-
-int checkboard(void)
-{
- printf("Board: MPC8308 P1M\n");
-
- return 0;
-}
-
-static struct pci_region pcie_regions_0[] = {
- {
- .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
- .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
- .size = CONFIG_SYS_PCIE1_MEM_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
- .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
- .size = CONFIG_SYS_PCIE1_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-void pci_init_board(void)
-{
- immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- sysconf83xx_t *sysconf = &immr->sysconf;
- law83xx_t *pcie_law = sysconf->pcielaw;
- struct pci_region *pcie_reg[] = { pcie_regions_0 };
-
- fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
-
- /* Deassert the resets in the control register */
- out_be32(&sysconf->pecr1, 0xE0008000);
- udelay(2000);
-
- /* Configure PCI Express Local Access Windows */
- out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
- out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
-
- mpc83xx_pcie_init(1, pcie_reg);
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, struct bd_info *bd)
-{
- ft_cpu_setup(blob, bd);
- fsl_fdt_fixup_dr_usb(blob, bd);
-
- return 0;
-}
-#endif
-
-int board_eth_init(struct bd_info *bis)
-{
- int rv, num_if = 0;
-
- /* Initialize TSECs first */
- rv = cpu_eth_init(bis);
- if (rv >= 0)
- num_if += rv;
- else
- printf("ERROR: failed to initialize TSECs.\n");
-
- rv = pci_eth_init(bis);
- if (rv >= 0)
- num_if += rv;
- else
- printf("ERROR: failed to initialize PCI Ethernet.\n");
-
- return num_if;
-}
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2007 Freescale Semiconductor, Inc.
- * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
- *
- * This files is mostly identical to the original from
- * board/freescale/mpc8308rdb/sdram.c
- */
-
-#include <common.h>
-#include <init.h>
-#include <mpc83xx.h>
-#include <asm/global_data.h>
-
-#include <asm/bitops.h>
-#include <asm/io.h>
-
-#include <asm/processor.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* Fixed sdram init -- doesn't use serial presence detect.
- *
- * This is useful for faster booting in configs where the RAM is unlikely
- * to be changed, or for things like NAND booting where space is tight.
- */
-static long fixed_sdram(void)
-{
- immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
- u32 msize_log2 = __ilog2(msize);
-
- out_be32(&im->sysconf.ddrlaw[0].bar,
- CONFIG_SYS_SDRAM_BASE & 0xfffff000);
- out_be32(&im->sysconf.ddrlaw[0].ar, LBLAWAR_EN | (msize_log2 - 1));
- out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
-
- out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
- out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CS0_CONFIG);
-
- /* Currently we use only one CS, so disable the other bank. */
- out_be32(&im->ddr.cs_config[1], 0);
-
- out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_SDRAM_CLK_CNTL);
- out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
- out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
- out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
- out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
-
- out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_DDR_SDRAM_CFG);
- out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_DDR_SDRAM_CFG2);
- out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
- out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE2);
-
- out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
- sync();
-
- /* enable DDR controller */
- setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
- sync();
-
- return get_ram_size(CONFIG_SYS_SDRAM_BASE, msize);
-}
-
-int dram_init(void)
-{
- immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize;
-
- if ((in_be32(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32)im)
- return -1;
-
- /* DDR SDRAM */
- msize = fixed_sdram();
-
- /* set total bus SDRAM size(bytes) -- DDR */
- gd->ram_size = msize;
-
- return 0;
-}
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xFC000000
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_SECT_SIZE=0x20000
-CONFIG_SYS_CLK_FREQ=33333333
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8308_P1M=y
-CONFIG_SYSTEM_PLL_VCO_DIV_2=y
-CONFIG_SYSTEM_PLL_FACTOR_4_1=y
-CONFIG_CORE_PLL_RATIO_3_1=y
-CONFIG_BOOT_MEMORY_SPACE_LOW=y
-CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
-CONFIG_BAT0=y
-CONFIG_BAT0_NAME="DDR"
-CONFIG_BAT0_BASE=0x00000000
-CONFIG_BAT0_LENGTH_128_MBYTES=y
-CONFIG_BAT0_ACCESS_RW=y
-CONFIG_BAT0_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_DCACHE_MEMORYCOHERENCE=y
-CONFIG_BAT0_USER_MODE_VALID=y
-CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT1=y
-CONFIG_BAT1_NAME="IMMRBAR"
-CONFIG_BAT1_BASE=0xE0000000
-CONFIG_BAT1_LENGTH_8_MBYTES=y
-CONFIG_BAT1_ACCESS_RW=y
-CONFIG_BAT1_ICACHE_INHIBITED=y
-CONFIG_BAT1_ICACHE_GUARDED=y
-CONFIG_BAT1_DCACHE_INHIBITED=y
-CONFIG_BAT1_DCACHE_GUARDED=y
-CONFIG_BAT1_USER_MODE_VALID=y
-CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT2=y
-CONFIG_BAT2_NAME="FLASH"
-CONFIG_BAT2_BASE=0xFC000000
-CONFIG_BAT2_LENGTH_8_MBYTES=y
-CONFIG_BAT2_ACCESS_RW=y
-CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
-CONFIG_BAT2_DCACHE_INHIBITED=y
-CONFIG_BAT2_DCACHE_GUARDED=y
-CONFIG_BAT2_USER_MODE_VALID=y
-CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
-CONFIG_BAT3=y
-CONFIG_BAT3_NAME="STACKINDCACHE"
-CONFIG_BAT3_BASE=0xE6000000
-CONFIG_BAT3_ACCESS_RW=y
-CONFIG_BAT3_USER_MODE_VALID=y
-CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
-CONFIG_LBLAW0=y
-CONFIG_LBLAW0_BASE=0xFC000000
-CONFIG_LBLAW0_NAME="FLASH"
-CONFIG_LBLAW0_LENGTH_64_MBYTES=y
-CONFIG_LBLAW1=y
-CONFIG_LBLAW1_BASE=0xFBFF0000
-CONFIG_LBLAW1_NAME="SJA1000"
-CONFIG_LBLAW1_LENGTH_32_KBYTES=y
-CONFIG_LBLAW2=y
-CONFIG_LBLAW2_BASE=0xFBFF8000
-CONFIG_LBLAW2_NAME="CPLD"
-CONFIG_LBLAW2_LENGTH_32_KBYTES=y
-CONFIG_ELBC_BR0_OR0=y
-CONFIG_BR0_OR0_NAME="FLASH"
-CONFIG_BR0_OR0_BASE=0xFC000000
-CONFIG_BR0_PORTSIZE_16BIT=y
-CONFIG_OR0_AM_64_MBYTES=y
-CONFIG_OR0_XAM_SET=y
-CONFIG_OR0_SCY_4=y
-CONFIG_OR0_CSNT_EARLIER=y
-CONFIG_OR0_ACS_HALF_CYCLE_EARLIER=y
-CONFIG_OR0_XACS_EXTENDED=y
-CONFIG_OR0_TRLX_RELAXED=y
-CONFIG_OR0_EHTR_8_CYCLE=y
-CONFIG_ELBC_BR1_OR1=y
-CONFIG_BR1_OR1_NAME="SJA1000"
-CONFIG_BR1_OR1_BASE=0xFBFF0000
-CONFIG_OR1_SCY_5=y
-CONFIG_OR1_EHTR_1_CYCLE=y
-CONFIG_ELBC_BR2_OR2=y
-CONFIG_BR2_OR2_NAME="CPLD"
-CONFIG_BR2_OR2_BASE=0xFBFF8000
-CONFIG_OR2_SCY_4=y
-CONFIG_OR2_EHTR_1_CYCLE=y
-CONFIG_HID0_FINAL_EMCP=y
-CONFIG_HID0_FINAL_DPM=y
-CONFIG_HID0_FINAL_ICE=y
-CONFIG_HID2_HBE=y
-CONFIG_SICR_ESDHC_A_GPIO=y
-CONFIG_SICR_ESDHC_B_GPIO=y
-CONFIG_SICR_ESDHC_C_GTM=y
-CONFIG_SICR_GPIO_A_TSEC2=y
-CONFIG_SICR_GPIO_B_TSEC2=y
-CONFIG_SICR_IEEE1588_A_GPIO=y
-CONFIG_SICR_GTM_GPIO=y
-CONFIG_SICR_GPIOSEL_IEEE1588=y
-CONFIG_ACR_PIPE_DEP_4=y
-CONFIG_ACR_RPTCNT_4=y
-CONFIG_SPCR_TSECEP_3=y
-CONFIG_LCRR_DBYP_PLL_BYPASSED=y
-CONFIG_LCRR_CLKDIV_2=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_BOOTDELAY=5
-CONFIG_HUSH_PARSER=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_PCI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_ENV_ADDR=0xFC060000
-CONFIG_ENV_ADDR_REDUND=0xFC080000
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_CFI_DRIVER=y
-CONFIG_SYS_FLASH_PROTECTION=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_PHY_ATHEROS=y
-CONFIG_PHY_BROADCOM=y
-CONFIG_PHY_DAVICOM=y
-CONFIG_PHY_LXT=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_NATSEMI=y
-CONFIG_PHY_REALTEK=y
-CONFIG_PHY_SMSC=y
-CONFIG_PHY_VITESSE=y
-CONFIG_MII=y
-CONFIG_TSEC_ENET=y
-CONFIG_SYS_NS16550=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
- * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <linux/stringify.h>
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-
-/*
- * On-board devices
- *
- * TSECs
- */
-#define CONFIG_TSEC1
-#define CONFIG_TSEC2
-
-#define CONFIG_SYS_GPIO1_PRELIM
-/* GPIO Default input/output settings */
-#define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00
-/*
- * Default GPIO values:
- * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
- */
-#define CONFIG_SYS_GPIO1_DAT 0x08008C00
-
-/*
- * SERDES
- */
-#define CONFIG_FSL_SERDES
-#define CONFIG_FSL_SERDES1 0xe3000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
- | DDRCDR_PZ_LOZ \
- | DDRCDR_NZ_LOZ \
- | DDRCDR_ODT \
- | DDRCDR_Q_DRN)
- /* 0x7b880001 */
-/*
- * Manually set up DDR parameters
- * consist of two chips HY5PS12621BFP-C4 from HYNIX
- */
-
-#define CONFIG_SYS_DDR_SIZE 128 /* MB */
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ODT_RD_NEVER \
- | CSCONFIG_ODT_WR_ONLY_CURRENT \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_10)
- /* 0x80010102 */
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
- | (0 << TIMING_CFG0_WRT_SHIFT) \
- | (0 << TIMING_CFG0_RRT_SHIFT) \
- | (0 << TIMING_CFG0_WWT_SHIFT) \
- | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
- | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
- | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
- /* 0x00220802 */
-#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
- | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
- | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
- | (5 << TIMING_CFG1_CASLAT_SHIFT) \
- | (6 << TIMING_CFG1_REFREC_SHIFT) \
- | (2 << TIMING_CFG1_WRREC_SHIFT) \
- | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
- | (2 << TIMING_CFG1_WRTORD_SHIFT))
- /* 0x27256222 */
-#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
- | (4 << TIMING_CFG2_CPO_SHIFT) \
- | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
- | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
- | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
- | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
- | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
- /* 0x121048c5 */
-#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
- | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
- /* 0x03600100 */
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
- | SDRAM_CFG_SDRAM_TYPE_DDR2 \
- | SDRAM_CFG_DBW_32)
- /* 0x43080000 */
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
- | (0x0232 << SDRAM_MODE_SD_SHIFT))
- /* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CONFIG_SYS_DDR_MODE2 0x00000000
-
-/*
- * Memory test
- */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-
-#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-
-/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024)
-/* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024)
-
-/*
- * SJA1000 CAN controller on Local Bus
- */
-#define CONFIG_SYS_SJA1000_BASE 0xFBFF0000
-
-
-/*
- * CPLD on Local Bus
- */
-#define CONFIG_SYS_CPLD_BASE 0xFBFF8000
-
-
-/*
- * Serial Port
- */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCIE1_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
-#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
-
-/* enable PCIE clock */
-#define CONFIG_SYS_SCCR_PCIEXP1CM 1
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
-
-/*
- * TSEC
- */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define CONFIG_TSEC2_NAME "eTSEC1"
-#define TSEC1_PHY_ADDR 1
-#define TSEC2_PHY_ADDR 2
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC1_FLAGS 0
-#define TSEC2_FLAGS 0
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME "eTSEC0"
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs}" \
- " console=${consoledev},${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addmisc=setenv bootargs ${bootargs}\0" \
- "kernel_addr=FC0A0000\0" \
- "fdt_addr=FC2A0000\0" \
- "ramdisk_addr=FC2C0000\0" \
- "u-boot=mpc8308_p1m/u-boot.bin\0" \
- "kernel_addr_r=1000000\0" \
- "fdt_addr_r=C00000\0" \
- "hostname=mpc8308_p1m\0" \
- "bootfile=mpc8308_p1m/uImage\0" \
- "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \
- "rootpath=/opt/eldk-4.2/ppc_6xx\0" \
- "flash_self=run ramargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
- "tftp ${fdt_addr_r} ${fdtfile};" \
- "run nfsargs addip addtty addmtd addmisc;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "bootcmd=run flash_self\0" \
- "load=tftp ${loadaddr} ${u-boot}\0" \
- "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
- " +${filesize};cp.b ${fileaddr} " \
- __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
- "upd=run load update\0" \
-
-#endif /* __CONFIG_H */
projects / uboot.git / commitdiff