--- /dev/null
+/*
+ * Texas Instruments DA8xx/OMAP-L1x "glue layer"
+ *
+ * Copyright (c) 2008-2009 MontaVista Software, Inc. <source@mvista.com>
+ *
+ * Based on the DaVinci "glue layer" code.
+ * Copyright (C) 2005-2006 by Texas Instruments
+ *
+ * This file is part of the Inventra Controller Driver for Linux.
+ *
+ * The Inventra Controller Driver for Linux is free software; you
+ * can redistribute it and/or modify it under the terms of the GNU
+ * General Public License version 2 as published by the Free Software
+ * Foundation.
+ *
+ * The Inventra Controller Driver for Linux is distributed in
+ * the hope that it will be useful, but WITHOUT ANY WARRANTY;
+ * without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
+ * License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with The Inventra Controller Driver for Linux ; if not,
+ * write to the Free Software Foundation, Inc., 59 Temple Place,
+ * Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <mach/da8xx.h>
+#include <mach/usb.h>
+
+#include "musb_core.h"
+
+/*
+ * DA8XX specific definitions
+ */
+
+/* USB 2.0 OTG module registers */
+#define DA8XX_USB_REVISION_REG 0x00
+#define DA8XX_USB_CTRL_REG 0x04
+#define DA8XX_USB_STAT_REG 0x08
+#define DA8XX_USB_EMULATION_REG 0x0c
+#define DA8XX_USB_MODE_REG 0x10 /* Transparent, CDC, [Generic] RNDIS */
+#define DA8XX_USB_AUTOREQ_REG 0x14
+#define DA8XX_USB_SRP_FIX_TIME_REG 0x18
+#define DA8XX_USB_TEARDOWN_REG 0x1c
+#define DA8XX_USB_INTR_SRC_REG 0x20
+#define DA8XX_USB_INTR_SRC_SET_REG 0x24
+#define DA8XX_USB_INTR_SRC_CLEAR_REG 0x28
+#define DA8XX_USB_INTR_MASK_REG 0x2c
+#define DA8XX_USB_INTR_MASK_SET_REG 0x30
+#define DA8XX_USB_INTR_MASK_CLEAR_REG 0x34
+#define DA8XX_USB_INTR_SRC_MASKED_REG 0x38
+#define DA8XX_USB_END_OF_INTR_REG 0x3c
+#define DA8XX_USB_GENERIC_RNDIS_EP_SIZE_REG(n) (0x50 + (((n) - 1) << 2))
+
+/* Control register bits */
+#define DA8XX_SOFT_RESET_MASK 1
+
+#define DA8XX_USB_TX_EP_MASK 0x1f /* EP0 + 4 Tx EPs */
+#define DA8XX_USB_RX_EP_MASK 0x1e /* 4 Rx EPs */
+
+/* USB interrupt register bits */
+#define DA8XX_INTR_USB_SHIFT 16
+#define DA8XX_INTR_USB_MASK (0x1ff << DA8XX_INTR_USB_SHIFT) /* 8 Mentor */
+ /* interrupts and DRVVBUS interrupt */
+#define DA8XX_INTR_DRVVBUS 0x100
+#define DA8XX_INTR_RX_SHIFT 8
+#define DA8XX_INTR_RX_MASK (DA8XX_USB_RX_EP_MASK << DA8XX_INTR_RX_SHIFT)
+#define DA8XX_INTR_TX_SHIFT 0
+#define DA8XX_INTR_TX_MASK (DA8XX_USB_TX_EP_MASK << DA8XX_INTR_TX_SHIFT)
+
+#define DA8XX_MENTOR_CORE_OFFSET 0x400
+
+#define CFGCHIP2 IO_ADDRESS(DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP2_REG)
+
+/*
+ * REVISIT (PM): we should be able to keep the PHY in low power mode most
+ * of the time (24 MHz oscillator and PLL off, etc.) by setting POWER.D0
+ * and, when in host mode, autosuspending idle root ports... PHY_PLLON
+ * (overriding SUSPENDM?) then likely needs to stay off.
+ */
+
+static inline void phy_on(void)
+{
+ u32 cfgchip2 = __raw_readl(CFGCHIP2);
+
+ /*
+ * Start the on-chip PHY and its PLL.
+ */
+ cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN);
+ cfgchip2 |= CFGCHIP2_PHY_PLLON;
+ __raw_writel(cfgchip2, CFGCHIP2);
+
+ pr_info("Waiting for USB PHY clock good...\n");
+ while (!(__raw_readl(CFGCHIP2) & CFGCHIP2_PHYCLKGD))
+ cpu_relax();
+}
+
+static inline void phy_off(void)
+{
+ u32 cfgchip2 = __raw_readl(CFGCHIP2);
+
+ /*
+ * Ensure that USB 1.1 reference clock is not being sourced from
+ * USB 2.0 PHY. Otherwise do not power down the PHY.
+ */
+ if (!(cfgchip2 & CFGCHIP2_USB1PHYCLKMUX) &&
+ (cfgchip2 & CFGCHIP2_USB1SUSPENDM)) {
+ pr_warning("USB 1.1 clocked from USB 2.0 PHY -- "
+ "can't power it down\n");
+ return;
+ }
+
+ /*
+ * Power down the on-chip PHY.
+ */
+ cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN;
+ __raw_writel(cfgchip2, CFGCHIP2);
+}
+
+/*
+ * Because we don't set CTRL.UINT, it's "important" to:
+ * - not read/write INTRUSB/INTRUSBE (except during
+ * initial setup, as a workaround);
+ * - use INTSET/INTCLR instead.
+ */
+
+/**
+ * musb_platform_enable - enable interrupts
+ */
+void musb_platform_enable(struct musb *musb)
+{
+ void __iomem *reg_base = musb->ctrl_base;
+ u32 mask;
+
+ /* Workaround: setup IRQs through both register sets. */
+ mask = ((musb->epmask & DA8XX_USB_TX_EP_MASK) << DA8XX_INTR_TX_SHIFT) |
+ ((musb->epmask & DA8XX_USB_RX_EP_MASK) << DA8XX_INTR_RX_SHIFT) |
+ DA8XX_INTR_USB_MASK;
+ musb_writel(reg_base, DA8XX_USB_INTR_MASK_SET_REG, mask);
+
+ /* Force the DRVVBUS IRQ so we can start polling for ID change. */
+ if (is_otg_enabled(musb))
+ musb_writel(reg_base, DA8XX_USB_INTR_SRC_SET_REG,
+ DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT);
+}
+
+/**
+ * musb_platform_disable - disable HDRC and flush interrupts
+ */
+void musb_platform_disable(struct musb *musb)
+{
+ void __iomem *reg_base = musb->ctrl_base;
+
+ musb_writel(reg_base, DA8XX_USB_INTR_MASK_CLEAR_REG,
+ DA8XX_INTR_USB_MASK |
+ DA8XX_INTR_TX_MASK | DA8XX_INTR_RX_MASK);
+ musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
+ musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0);
+}
+
+#ifdef CONFIG_USB_MUSB_HDRC_HCD
+#define portstate(stmt) stmt
+#else
+#define portstate(stmt)
+#endif
+
+static void da8xx_set_vbus(struct musb *musb, int is_on)
+{
+ WARN_ON(is_on && is_peripheral_active(musb));
+}
+
+#define POLL_SECONDS 2
+
+static struct timer_list otg_workaround;
+
+static void otg_timer(unsigned long _musb)
+{
+ struct musb *musb = (void *)_musb;
+ void __iomem *mregs = musb->mregs;
+ u8 devctl;
+ unsigned long flags;
+
+ /*
+ * We poll because DaVinci's won't expose several OTG-critical
+ * status change events (from the transceiver) otherwise.
+ */
+ devctl = musb_readb(mregs, MUSB_DEVCTL);
+ DBG(7, "Poll devctl %02x (%s)\n", devctl, otg_state_string(musb));
+
+ spin_lock_irqsave(&musb->lock, flags);
+ switch (musb->xceiv->state) {
+ case OTG_STATE_A_WAIT_BCON:
+ devctl &= ~MUSB_DEVCTL_SESSION;
+ musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
+
+ devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
+ if (devctl & MUSB_DEVCTL_BDEVICE) {
+ musb->xceiv->state = OTG_STATE_B_IDLE;
+ MUSB_DEV_MODE(musb);
+ } else {
+ musb->xceiv->state = OTG_STATE_A_IDLE;
+ MUSB_HST_MODE(musb);
+ }
+ break;
+ case OTG_STATE_A_WAIT_VFALL:
+ /*
+ * Wait till VBUS falls below SessionEnd (~0.2 V); the 1.3
+ * RTL seems to mis-handle session "start" otherwise (or in
+ * our case "recover"), in routine "VBUS was valid by the time
+ * VBUSERR got reported during enumeration" cases.
+ */
+ if (devctl & MUSB_DEVCTL_VBUS) {
+ mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
+ break;
+ }
+ musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
+ musb_writel(musb->ctrl_base, DA8XX_USB_INTR_SRC_SET_REG,
+ MUSB_INTR_VBUSERROR << DA8XX_INTR_USB_SHIFT);
+ break;
+ case OTG_STATE_B_IDLE:
+ if (!is_peripheral_enabled(musb))
+ break;
+
+ /*
+ * There's no ID-changed IRQ, so we have no good way to tell
+ * when to switch to the A-Default state machine (by setting
+ * the DEVCTL.Session bit).
+ *
+ * Workaround: whenever we're in B_IDLE, try setting the
+ * session flag every few seconds. If it works, ID was
+ * grounded and we're now in the A-Default state machine.
+ *
+ * NOTE: setting the session flag is _supposed_ to trigger
+ * SRP but clearly it doesn't.
+ */
+ musb_writeb(mregs, MUSB_DEVCTL, devctl | MUSB_DEVCTL_SESSION);
+ devctl = musb_readb(mregs, MUSB_DEVCTL);
+ if (devctl & MUSB_DEVCTL_BDEVICE)
+ mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
+ else
+ musb->xceiv->state = OTG_STATE_A_IDLE;
+ break;
+ default:
+ break;
+ }
+ spin_unlock_irqrestore(&musb->lock, flags);
+}
+
+void musb_platform_try_idle(struct musb *musb, unsigned long timeout)
+{
+ static unsigned long last_timer;
+
+ if (!is_otg_enabled(musb))
+ return;
+
+ if (timeout == 0)
+ timeout = jiffies + msecs_to_jiffies(3);
+
+ /* Never idle if active, or when VBUS timeout is not set as host */
+ if (musb->is_active || (musb->a_wait_bcon == 0 &&
+ musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) {
+ DBG(4, "%s active, deleting timer\n", otg_state_string(musb));
+ del_timer(&otg_workaround);
+ last_timer = jiffies;
+ return;
+ }
+
+ if (time_after(last_timer, timeout) && timer_pending(&otg_workaround)) {
+ DBG(4, "Longer idle timer already pending, ignoring...\n");
+ return;
+ }
+ last_timer = timeout;
+
+ DBG(4, "%s inactive, starting idle timer for %u ms\n",
+ otg_state_string(musb), jiffies_to_msecs(timeout - jiffies));
+ mod_timer(&otg_workaround, timeout);
+}
+
+static irqreturn_t da8xx_interrupt(int irq, void *hci)
+{
+ struct musb *musb = hci;
+ void __iomem *reg_base = musb->ctrl_base;
+ unsigned long flags;
+ irqreturn_t ret = IRQ_NONE;
+ u32 status;
+
+ spin_lock_irqsave(&musb->lock, flags);
+
+ /*
+ * NOTE: DA8XX shadows the Mentor IRQs. Don't manage them through
+ * the Mentor registers (except for setup), use the TI ones and EOI.
+ */
+
+ /* Acknowledge and handle non-CPPI interrupts */
+ status = musb_readl(reg_base, DA8XX_USB_INTR_SRC_MASKED_REG);
+ if (!status)
+ goto eoi;
+
+ musb_writel(reg_base, DA8XX_USB_INTR_SRC_CLEAR_REG, status);
+ DBG(4, "USB IRQ %08x\n", status);
+
+ musb->int_rx = (status & DA8XX_INTR_RX_MASK) >> DA8XX_INTR_RX_SHIFT;
+ musb->int_tx = (status & DA8XX_INTR_TX_MASK) >> DA8XX_INTR_TX_SHIFT;
+ musb->int_usb = (status & DA8XX_INTR_USB_MASK) >> DA8XX_INTR_USB_SHIFT;
+
+ /*
+ * DRVVBUS IRQs are the only proxy we have (a very poor one!) for
+ * DA8xx's missing ID change IRQ. We need an ID change IRQ to
+ * switch appropriately between halves of the OTG state machine.
+ * Managing DEVCTL.Session per Mentor docs requires that we know its
+ * value but DEVCTL.BDevice is invalid without DEVCTL.Session set.
+ * Also, DRVVBUS pulses for SRP (but not at 5 V)...
+ */
+ if (status & (DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT)) {
+ int drvvbus = musb_readl(reg_base, DA8XX_USB_STAT_REG);
+ void __iomem *mregs = musb->mregs;
+ u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
+ int err;
+
+ err = is_host_enabled(musb) && (musb->int_usb &
+ MUSB_INTR_VBUSERROR);
+ if (err) {
+ /*
+ * The Mentor core doesn't debounce VBUS as needed
+ * to cope with device connect current spikes. This
+ * means it's not uncommon for bus-powered devices
+ * to get VBUS errors during enumeration.
+ *
+ * This is a workaround, but newer RTL from Mentor
+ * seems to allow a better one: "re"-starting sessions
+ * without waiting for VBUS to stop registering in
+ * devctl.
+ */
+ musb->int_usb &= ~MUSB_INTR_VBUSERROR;
+ musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
+ mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
+ WARNING("VBUS error workaround (delay coming)\n");
+ } else if (is_host_enabled(musb) && drvvbus) {
+ MUSB_HST_MODE(musb);
+ musb->xceiv->default_a = 1;
+ musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
+ portstate(musb->port1_status |= USB_PORT_STAT_POWER);
+ del_timer(&otg_workaround);
+ } else {
+ musb->is_active = 0;
+ MUSB_DEV_MODE(musb);
+ musb->xceiv->default_a = 0;
+ musb->xceiv->state = OTG_STATE_B_IDLE;
+ portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
+ }
+
+ DBG(2, "VBUS %s (%s)%s, devctl %02x\n",
+ drvvbus ? "on" : "off",
+ otg_state_string(musb),
+ err ? " ERROR" : "",
+ devctl);
+ ret = IRQ_HANDLED;
+ }
+
+ if (musb->int_tx || musb->int_rx || musb->int_usb)
+ ret |= musb_interrupt(musb);
+
+ eoi:
+ /* EOI needs to be written for the IRQ to be re-asserted. */
+ if (ret == IRQ_HANDLED || status)
+ musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0);
+
+ /* Poll for ID change */
+ if (is_otg_enabled(musb) && musb->xceiv->state == OTG_STATE_B_IDLE)
+ mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
+
+ spin_unlock_irqrestore(&musb->lock, flags);
+
+ return ret;
+}
+
+int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
+{
+ u32 cfgchip2 = __raw_readl(CFGCHIP2);
+
+ cfgchip2 &= ~CFGCHIP2_OTGMODE;
+ switch (musb_mode) {
+#ifdef CONFIG_USB_MUSB_HDRC_HCD
+ case MUSB_HOST: /* Force VBUS valid, ID = 0 */
+ cfgchip2 |= CFGCHIP2_FORCE_HOST;
+ break;
+#endif
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
+ case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */
+ cfgchip2 |= CFGCHIP2_FORCE_DEVICE;
+ break;
+#endif
+#ifdef CONFIG_USB_MUSB_OTG
+ case MUSB_OTG: /* Don't override the VBUS/ID comparators */
+ cfgchip2 |= CFGCHIP2_NO_OVERRIDE;
+ break;
+#endif
+ default:
+ DBG(2, "Trying to set unsupported mode %u\n", musb_mode);
+ }
+
+ __raw_writel(cfgchip2, CFGCHIP2);
+ return 0;
+}
+
+int __init musb_platform_init(struct musb *musb, void *board_data)
+{
+ void __iomem *reg_base = musb->ctrl_base;
+ u32 rev;
+
+ musb->mregs += DA8XX_MENTOR_CORE_OFFSET;
+
+ clk_enable(musb->clock);
+
+ /* Returns zero if e.g. not clocked */
+ rev = musb_readl(reg_base, DA8XX_USB_REVISION_REG);
+ if (!rev)
+ goto fail;
+
+ usb_nop_xceiv_register();
+ musb->xceiv = otg_get_transceiver();
+ if (!musb->xceiv)
+ goto fail;
+
+ if (is_host_enabled(musb))
+ setup_timer(&otg_workaround, otg_timer, (unsigned long)musb);
+
+ musb->board_set_vbus = da8xx_set_vbus;
+
+ /* Reset the controller */
+ musb_writel(reg_base, DA8XX_USB_CTRL_REG, DA8XX_SOFT_RESET_MASK);
+
+ /* Start the on-chip PHY and its PLL. */
+ phy_on();
+
+ msleep(5);
+
+ /* NOTE: IRQs are in mixed mode, not bypass to pure MUSB */
+ pr_debug("DA8xx OTG revision %08x, PHY %03x, control %02x\n",
+ rev, __raw_readl(CFGCHIP2),
+ musb_readb(reg_base, DA8XX_USB_CTRL_REG));
+
+ musb->isr = da8xx_interrupt;
+ return 0;
+fail:
+ clk_disable(musb->clock);
+ return -ENODEV;
+}
+
+int musb_platform_exit(struct musb *musb)
+{
+ if (is_host_enabled(musb))
+ del_timer_sync(&otg_workaround);
+
+ phy_off();
+
+ otg_put_transceiver(musb->xceiv);
+ usb_nop_xceiv_unregister();
+
+ clk_disable(musb->clock);
+
+ return 0;
+}
projects / kernel.git / commitdiff