+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Keymile AG
- * Gerlando Falauto <gerlando.falauto@keymile.com>
- *
- * Based on km8321-common.h, see respective copyright notice for credits
- */
-
-#ifndef __CONFIG_KM8309_COMMON_H
-#define __CONFIG_KM8309_COMMON_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_QE 1 /* Has QE */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-
-/* include common defines/options for all 83xx Keymile boards */
-#include "km83xx-common.h"
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-/* between the u-boot partition and env */
-#ifndef CONFIG_SYS_QE_FW_ADDR
-#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
-#endif
-
-/*
- * System IO Config
- */
-/* 0x14000180 SICR_1 */
-#define CONFIG_SYS_SICRL (0 \
- | SICR_1_UART1_UART1RTS \
- | SICR_1_I2C_CKSTOP \
- | SICR_1_IRQ_A_IRQ \
- | SICR_1_IRQ_B_IRQ \
- | SICR_1_GPIO_A_GPIO \
- | SICR_1_GPIO_B_GPIO \
- | SICR_1_GPIO_C_GPIO \
- | SICR_1_GPIO_D_GPIO \
- | SICR_1_GPIO_E_GPIO \
- | SICR_1_GPIO_F_GPIO \
- | SICR_1_USB_A_UART2S \
- | SICR_1_USB_B_UART2RTS \
- | SICR_1_FEC1_FEC1 \
- | SICR_1_FEC2_FEC2 \
- )
-
-/* 0x00080400 SICR_2 */
-#define CONFIG_SYS_SICRH (0 \
- | SICR_2_FEC3_FEC3 \
- | SICR_2_HDLC1_A_HDLC1 \
- | SICR_2_ELBC_A_LA \
- | SICR_2_ELBC_B_LCLK \
- | SICR_2_HDLC2_A_HDLC2 \
- | SICR_2_USB_D_GPIO \
- | SICR_2_PCI_PCI \
- | SICR_2_HDLC1_B_HDLC1 \
- | SICR_2_HDLC1_C_HDLC1 \
- | SICR_2_HDLC2_B_GPIO \
- | SICR_2_HDLC2_C_HDLC2 \
- | SICR_2_QUIESCE_B \
- )
-
-/* GPR_1 */
-#define CONFIG_SYS_GPR1 0x50008060
-
-#define CONFIG_SYS_GP1DIR 0x00000000
-#define CONFIG_SYS_GP1ODR 0x00000000
-#define CONFIG_SYS_GP2DIR 0xFF000000
-#define CONFIG_SYS_GP2ODR 0x00000000
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
- HRCWL_DDR_TO_SCB_CLK_2X1 | \
- HRCWL_CSB_TO_CLKIN_2X1 | \
- HRCWL_CORE_TO_CSB_2X1 | \
- HRCWL_CE_PLL_VCO_DIV_2 | \
- HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_AGENT | \
- HRCWH_PCI_ARBITER_DISABLE | \
- HRCWH_CORE_ENABLE | \
- HRCWH_FROM_0X00000100 | \
- HRCWH_BOOTSEQ_DISABLE | \
- HRCWH_SW_WATCHDOG_DISABLE | \
- HRCWH_ROM_LOC_LOCAL_16BIT | \
- HRCWH_BIG_ENDIAN | \
- HRCWH_LALE_NORMAL)
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_RD_NEVER | \
- CSCONFIG_ODT_WR_ONLY_CURRENT | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP 0x80000000
-#define CONFIG_SYS_LCRR_EADC 0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
-
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-#endif /* __CONFIG_KM8309_COMMON_H */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- * Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- * Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * (C) Copyright 2010
- * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
- *
- * (C) Copyright 2010-2011
- * Thomas Reufer, KEYMILE Ltd, thomas.reufer@keymile.com
- */
-
-#ifndef __CONFIG_KM8321_COMMON_H
-#define __CONFIG_KM8321_COMMON_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE /* Has QE */
-#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
-
-/* include common defines/options for all 83xx Keymile boards */
-#include "km83xx-common.h"
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
- HRCWL_DDR_TO_SCB_CLK_2X1 | \
- HRCWL_CSB_TO_CLKIN_2X1 | \
- HRCWL_CORE_TO_CSB_2_5X1 | \
- HRCWL_CE_PLL_VCO_DIV_2 | \
- HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_AGENT | \
- HRCWH_PCI_ARBITER_DISABLE | \
- HRCWH_CORE_ENABLE | \
- HRCWH_FROM_0X00000100 | \
- HRCWH_BOOTSEQ_DISABLE | \
- HRCWH_SW_WATCHDOG_DISABLE | \
- HRCWH_ROM_LOC_LOCAL_16BIT | \
- HRCWH_BIG_ENDIAN | \
- HRCWH_LALE_NORMAL)
-
-#define CONFIG_SYS_DDRCDR (\
- DDRCDR_EN | \
- DDRCDR_PZ_MAXZ | \
- DDRCDR_NZ_MAXZ | \
- DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
- SDRAM_CFG_32_BE | \
- SDRAM_CFG_SREN | \
- SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
- (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ODT_WR_CFG | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE 0x47860242
-#define CONFIG_SYS_DDR_MODE2 0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (7 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP 0x80000000
-#define CONFIG_SYS_LCRR_EADC 0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
-
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-#endif /* __CONFIG_KM8321_COMMON_H */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-/* include common defines/options for all 8309 Keymile boards */
-#include "km8309-common.h"
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_QE 1 /* Has QE */
+
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0 \
+ | SICR_1_UART1_UART1RTS \
+ | SICR_1_I2C_CKSTOP \
+ | SICR_1_IRQ_A_IRQ \
+ | SICR_1_IRQ_B_IRQ \
+ | SICR_1_GPIO_A_GPIO \
+ | SICR_1_GPIO_B_GPIO \
+ | SICR_1_GPIO_C_GPIO \
+ | SICR_1_GPIO_D_GPIO \
+ | SICR_1_GPIO_E_GPIO \
+ | SICR_1_GPIO_F_GPIO \
+ | SICR_1_USB_A_UART2S \
+ | SICR_1_USB_B_UART2RTS \
+ | SICR_1_FEC1_FEC1 \
+ | SICR_1_FEC2_FEC2 \
+ )
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0 \
+ | SICR_2_FEC3_FEC3 \
+ | SICR_2_HDLC1_A_HDLC1 \
+ | SICR_2_ELBC_A_LA \
+ | SICR_2_ELBC_B_LCLK \
+ | SICR_2_HDLC2_A_HDLC2 \
+ | SICR_2_USB_D_GPIO \
+ | SICR_2_PCI_PCI \
+ | SICR_2_HDLC1_B_HDLC1 \
+ | SICR_2_HDLC1_C_HDLC1 \
+ | SICR_2_HDLC2_B_GPIO \
+ | SICR_2_HDLC2_C_HDLC2 \
+ | SICR_2_QUIESCE_B \
+ )
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1 0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+ HRCWL_DDR_TO_SCB_CLK_2X1 | \
+ HRCWL_CSB_TO_CLKIN_2X1 | \
+ HRCWL_CORE_TO_CSB_2X1 | \
+ HRCWL_CE_PLL_VCO_DIV_2 | \
+ HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_AGENT | \
+ HRCWH_PCI_ARBITER_DISABLE | \
+ HRCWH_CORE_ENABLE | \
+ HRCWH_FROM_0X00000100 | \
+ HRCWH_BOOTSEQ_DISABLE | \
+ HRCWH_SW_WATCHDOG_DISABLE | \
+ HRCWH_ROM_LOC_LOCAL_16BIT | \
+ HRCWH_BIG_ENDIAN | \
+ HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_RD_NEVER | \
+ CSCONFIG_ODT_WR_ONLY_CURRENT | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP 0x80000000
+#define CONFIG_SYS_LCRR_EADC 0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
+
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
/* must be after the include because KMBEC_FPGA is otherwise undefined */
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
#define CONFIG_KM_BOARD_NAME "kmvect1"
/* at end of uboot partition, before env */
#define CONFIG_SYS_QE_FW_ADDR 0xF00B0000
-/* include common defines/options for all 8309 Keymile boards */
-#include "km8309-common.h"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1 /* E300 family */
+#define CONFIG_QE 1 /* Has QE */
+
+#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR 0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0 \
+ | SICR_1_UART1_UART1RTS \
+ | SICR_1_I2C_CKSTOP \
+ | SICR_1_IRQ_A_IRQ \
+ | SICR_1_IRQ_B_IRQ \
+ | SICR_1_GPIO_A_GPIO \
+ | SICR_1_GPIO_B_GPIO \
+ | SICR_1_GPIO_C_GPIO \
+ | SICR_1_GPIO_D_GPIO \
+ | SICR_1_GPIO_E_GPIO \
+ | SICR_1_GPIO_F_GPIO \
+ | SICR_1_USB_A_UART2S \
+ | SICR_1_USB_B_UART2RTS \
+ | SICR_1_FEC1_FEC1 \
+ | SICR_1_FEC2_FEC2 \
+ )
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0 \
+ | SICR_2_FEC3_FEC3 \
+ | SICR_2_HDLC1_A_HDLC1 \
+ | SICR_2_ELBC_A_LA \
+ | SICR_2_ELBC_B_LCLK \
+ | SICR_2_HDLC2_A_HDLC2 \
+ | SICR_2_USB_D_GPIO \
+ | SICR_2_PCI_PCI \
+ | SICR_2_HDLC1_B_HDLC1 \
+ | SICR_2_HDLC1_C_HDLC1 \
+ | SICR_2_HDLC2_B_GPIO \
+ | SICR_2_HDLC2_C_HDLC2 \
+ | SICR_2_QUIESCE_B \
+ )
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1 0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+ HRCWL_DDR_TO_SCB_CLK_2X1 | \
+ HRCWL_CSB_TO_CLKIN_2X1 | \
+ HRCWL_CORE_TO_CSB_2X1 | \
+ HRCWL_CE_PLL_VCO_DIV_2 | \
+ HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_AGENT | \
+ HRCWH_PCI_ARBITER_DISABLE | \
+ HRCWH_CORE_ENABLE | \
+ HRCWH_FROM_0X00000100 | \
+ HRCWH_BOOTSEQ_DISABLE | \
+ HRCWH_SW_WATCHDOG_DISABLE | \
+ HRCWH_ROM_LOC_LOCAL_16BIT | \
+ HRCWH_BIG_ENDIAN | \
+ HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_RD_NEVER | \
+ CSCONFIG_ODT_WR_ONLY_CURRENT | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP 0x80000000
+#define CONFIG_SYS_LCRR_EADC 0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
+
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#define CONFIG_SYS_APP1_BASE 0xA0000000
#define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */
#define CONFIG_HOSTNAME "suvd3"
#define CONFIG_KM_BOARD_NAME "suvd3"
-/* include common defines/options for all 8321 Keymile boards */
-#include "km8321-common.h"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE /* Has QE */
+#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
+
+#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+ HRCWL_DDR_TO_SCB_CLK_2X1 | \
+ HRCWL_CSB_TO_CLKIN_2X1 | \
+ HRCWL_CORE_TO_CSB_2_5X1 | \
+ HRCWL_CE_PLL_VCO_DIV_2 | \
+ HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_AGENT | \
+ HRCWH_PCI_ARBITER_DISABLE | \
+ HRCWH_CORE_ENABLE | \
+ HRCWH_FROM_0X00000100 | \
+ HRCWH_BOOTSEQ_DISABLE | \
+ HRCWH_SW_WATCHDOG_DISABLE | \
+ HRCWH_ROM_LOC_LOCAL_16BIT | \
+ HRCWH_BIG_ENDIAN | \
+ HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_WR_CFG | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP 0x80000000
+#define CONFIG_SYS_LCRR_EADC 0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
+
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#define CONFIG_SYS_APP1_BASE 0xA0000000
#define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */
#error ("Board not supported")
#endif
-/* include common defines/options for all 8321 Keymile boards */
-#include "km8321-common.h"
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE /* Has QE */
+#define CONFIG_KM8321 /* Keymile PBEC8321 board specific */
+
+#define CONFIG_KM_DEF_ARCH "arch=ppc_8xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL SICRL_IRQ_CKS
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+ HRCWL_DDR_TO_SCB_CLK_2X1 | \
+ HRCWL_CSB_TO_CLKIN_2X1 | \
+ HRCWL_CORE_TO_CSB_2_5X1 | \
+ HRCWL_CE_PLL_VCO_DIV_2 | \
+ HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+ HRCWH_PCI_AGENT | \
+ HRCWH_PCI_ARBITER_DISABLE | \
+ HRCWH_CORE_ENABLE | \
+ HRCWH_FROM_0X00000100 | \
+ HRCWH_BOOTSEQ_DISABLE | \
+ HRCWH_SW_WATCHDOG_DISABLE | \
+ HRCWH_ROM_LOC_LOCAL_16BIT | \
+ HRCWH_BIG_ENDIAN | \
+ HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+ DDRCDR_EN | \
+ DDRCDR_PZ_MAXZ | \
+ DDRCDR_NZ_MAXZ | \
+ DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+ SDRAM_CFG_32_BE | \
+ SDRAM_CFG_SREN | \
+ SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+ (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ODT_WR_CFG | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE 0x47860242
+#define CONFIG_SYS_DDR_MODE2 0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+ (0 << TIMING_CFG0_WWT_SHIFT) | \
+ (0 << TIMING_CFG0_RRT_SHIFT) | \
+ (0 << TIMING_CFG0_WRT_SHIFT) | \
+ (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \
+ (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+ (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+ (3 << TIMING_CFG1_WRREC_SHIFT) | \
+ (7 << TIMING_CFG1_REFREC_SHIFT) | \
+ (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+ (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+ (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+ (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+ (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE 128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP 0x80000000
+#define CONFIG_SYS_LCRR_EADC 0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV 0x00000002
+
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L (0)
+#define CONFIG_SYS_IBAT7U (0)
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#define CONFIG_SYS_APP1_BASE 0xA0000000 /* PAXG */
#define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */
projects / uboot.git / commitdiff