This enables the 'errata' command which displays a list of errata
work-arounds which are enabled for the current board.
+config FSL_PREPBL_ESDHC_BOOT_SECTOR
+ bool "Generate QorIQ pre-PBL eSDHC boot sector"
+ depends on MPC85xx
+ depends on SYS_EXTRA_OPTIONS = SDCARD
+ help
+ With this option final image would have prepended QorIQ pre-PBL eSDHC
+ boot sector suitable for SD card images. This boot sector instruct
+ BootROM to configure L2 SRAM and eSDHC then load image from SD card
+ into L2 SRAM and finally jump to image entry point.
+
+ This is alternative to Freescale boot_format tool, but works only for
+ SD card images and only for L2 SRAM booting. U-Boot images generated
+ with this option should not passed to boot_format tool.
+
+ For other configuration like booting from eSPI or configuring SDRAM
+ please use Freescale boot_format tool without this option. See file
+ doc/README.mpc85xx-sd-spi-boot
+
+config FSL_PREPBL_ESDHC_BOOT_SECTOR_START
+ int "QorIQ pre-PBL eSDHC boot sector start offset"
+ depends on FSL_PREPBL_ESDHC_BOOT_SECTOR
+ range 0 23
+ default 0
+ help
+ QorIQ pre-PBL eSDHC boot sector may be located on one of the first
+ 24 SD card sectors. Select SD card sector on which final U-Boot
+ image (with this boot sector) would be installed.
+
+ By default first SD card sector (0) is used. But this may be changed
+ to allow installing U-Boot image on some partition (with fixed start
+ sector).
+
+ Please note that any sector on SD card prior this boot sector must
+ not contain ASCII "BOOT" bytes at sector offset 0x40.
+
+config FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA
+ int "Relative data sector for QorIQ pre-PBL eSDHC boot sector"
+ depends on FSL_PREPBL_ESDHC_BOOT_SECTOR
+ default 1
+ range 1 8388607
+ help
+ Select data sector from the beginning of QorIQ pre-PBL eSDHC boot
+ sector on which would be stored raw U-Boot image.
+
+ By default is it second sector (1) which is the first available free
+ sector (on the first sector is stored boot sector). It can be any
+ sector number which offset in bytes can be expressed by 32-bit number.
+
+ In case this final U-Boot image (with this boot sector) is put on
+ the FAT32 partition into reserved boot area, this data sector needs
+ to be at least 2 (third sector) because FAT32 use second sector for
+ its data.
+
choice
prompt "Target select"
optional
GOT_ENTRY(__bss_start)
END_GOT
+#ifdef CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+
+/* Maximal size of the image */
+#ifdef CONFIG_SPL_BUILD
+#define MAX_IMAGE_SIZE (CONFIG_SPL_MAX_SIZE - (CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA * 512))
+#else
+#define MAX_IMAGE_SIZE CONFIG_SYS_L2_SIZE
+#endif
+
+#if defined(CONFIG_SPL_BUILD) && CONFIG_SPL_MAX_SIZE < CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA * 512
+#error "CONFIG_SPL_MAX_SIZE is too small for CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA"
+#endif
+
+#if MAX_IMAGE_SIZE > CONFIG_SYS_L2_SIZE
+#error "Image is too big"
+#endif
+
+#define DIV_ROUND_UP(a, b) (((a) + (b) - 1) / (b))
+#define ALIGN(x, a) (DIV_ROUND_UP(x, a) * (a))
+
+/* Definitions from C header file asm/immap_85xx.h */
+
+#define CONFIG_SYS_MPC85xx_L2_OFFSET 0x20000
+
+#define MPC85xx_L2CTL 0x000
+#define MPC85xx_L2CTL_L2E 0x80000000
+#define MPC85xx_L2CTL_L2SRAM_ENTIRE 0x00010000
+
+#define MPC85xx_L2SRBAR0 0x100
+
+#define MPC85xx_L2ERRDIS 0xe44
+#define MPC85xx_L2ERRDIS_MBECC 0x00000008
+#define MPC85xx_L2ERRDIS_SBECC 0x00000004
+
+/* Definitions from C header file fsl_esdhc.h */
+
+#define ESDHCCTL 0x0002e40c
+#define ESDHCCTL_SNOOP 0x00000040
+
+/*
+ * QorIQ pre-PBL eSDHC boot sector:
+ * Instruct BootROM to configure L2 SRAM and eSDHC then load image
+ * from SD card into L2 SRAM and finally jump to image entry point.
+ */
+ .section .bootsect, "a"
+ .globl bootsect
+
+bootsect:
+ .org 0x40 /* BOOT signature */
+ .ascii "BOOT"
+
+ .org 0x48 /* Number of bytes to be copied, must be multiple of block size (512) */
+ .long ALIGN(MAX_IMAGE_SIZE, 512)
+
+ .org 0x50 /* Source address from the beginning of boot sector in byte address format, must be multiple of block size (512) */
+ .long (CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_START + CONFIG_FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA) * 512
+
+ .org 0x58 /* Target address in the system's local memory address space */
+ .long CONFIG_SYS_MONITOR_BASE
+
+ .org 0x60 /* Execution starting address */
+ .long _start
+
+ .org 0x68 /* Number of configuration data pairs */
+ .long DIV_ROUND_UP(.Lconf_pair_end - .Lconf_pair_start, 8)
+
+ .org 0x80 /* Start of configuration */
+ .Lconf_pair_start:
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + CONFIG_SYS_MPC85xx_L2_OFFSET + MPC85xx_L2SRBAR0 /* Address: L2 memory-mapped SRAM base addr 0 */
+ .long CONFIG_SYS_INIT_L2_ADDR
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + CONFIG_SYS_MPC85xx_L2_OFFSET + MPC85xx_L2ERRDIS /* Address: L2 cache error disable */
+ .long MPC85xx_L2ERRDIS_MBECC | MPC85xx_L2ERRDIS_SBECC
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + CONFIG_SYS_MPC85xx_L2_OFFSET + MPC85xx_L2CTL /* Address: L2 configuration 0 */
+ .long MPC85xx_L2CTL_L2E | MPC85xx_L2CTL_L2SRAM_ENTIRE
+
+ .long CONFIG_SYS_CCSRBAR_DEFAULT + ESDHCCTL /* Address: eSDHC DMA control */
+ .long ESDHCCTL_SNOOP
+
+ .long 0x40000001 /* Command: Delay in 8 CCB clocks */
+ .long 256
+
+ .long 0x80000001 /* End of configuration */
+ .Lconf_pair_end:
+
+ .org 0x1b8 /* Reserved for MBR/DBR */
+ .org 0x200 /* End of boot sector */
+
+#endif
+#endif
+
/*
* e500 Startup -- after reset only the last 4KB of the effective
* address space is mapped in the MMU L2 TLB1 Entry0. The .bootpg
projects / uboot.git / commitdiff