Optional Properties:
- reg-names: In addition to the required properties, the following are optional
- "efuse-address" - Contains efuse base address used to pick up ABB info.
- - "ldo-address" - Contains address of ABB LDO overide register address.
+ - "ldo-address" - Contains address of ABB LDO override register.
"efuse-address" is required for this.
- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override
register to provide override vset value.
the slower the port i/o. In some cases, setting
this to zero will speed up the device. (default -1)
- major You may use this parameter to overide the
+ major You may use this parameter to override the
default major number (46) that this driver
will use. Be sure to change the device
name as well.
first drive found.
- major You may use this parameter to overide the
+ major You may use this parameter to override the
default major number (45) that this driver
will use. Be sure to change the device
name as well.
the slower the port i/o. In some cases, setting
this to zero will speed up the device. (default -1)
- major You may use this parameter to overide the
+ major You may use this parameter to override the
default major number (47) that this driver
will use. Be sure to change the device
name as well.
the slower the port i/o. In some cases, setting
this to zero will speed up the device. (default -1)
- major You may use this parameter to overide the
+ major You may use this parameter to override the
default major number (97) that this driver
will use. Be sure to change the device
name as well.
the slower the port i/o. In some cases, setting
this to zero will speed up the device. (default -1)
- major You may use this parameter to overide the
+ major You may use this parameter to override the
default major number (96) that this driver
will use. Be sure to change the device
name as well.
*
* The actual DAP implementation may be restricted to only one of the modes.
* A compiler warning or error will be generated if the DAP implementation
-* overides or cannot handle the mode defined below.
-*
+* overrides or cannot handle the mode defined below.
*/
#ifndef DRXDAP_SINGLE_MASTER
#define DRXDAP_SINGLE_MASTER 1
*
* This maximum size may be restricted by the actual DAP implementation.
* A compiler warning or error will be generated if the DAP implementation
-* overides or cannot handle the chunksize defined below.
+* overrides or cannot handle the chunksize defined below.
*
* Beware that the DAP uses DRXDAP_MAX_WCHUNKSIZE to create a temporary data
* buffer. Do not undefine or choose too large, unless your system is able to
*
* This maximum size may be restricted by the actual DAP implementation.
* A compiler warning or error will be generated if the DAP implementation
-* overides or cannot handle the chunksize defined below.
-*
+* overrides or cannot handle the chunksize defined below.
*/
#ifndef DRXDAP_MAX_RCHUNKSIZE
#define DRXDAP_MAX_RCHUNKSIZE 60
struct ib_mac_iocb_rsp {
u8 opcode; /* 0x20 */
u8 flags1;
-#define IB_MAC_IOCB_RSP_OI 0x01 /* Overide intr delay */
+#define IB_MAC_IOCB_RSP_OI 0x01 /* Override intr delay */
#define IB_MAC_IOCB_RSP_I 0x02 /* Disable Intr Generation */
#define IB_MAC_CSUM_ERR_MASK 0x1c /* A mask to use for csum errs */
#define IB_MAC_IOCB_RSP_TE 0x04 /* Checksum error */
#define CS42L42_HPOUT_LOAD_1NF 0
#define CS42L42_HPOUT_LOAD_10NF 1
-/* HPOUT Clamp to GND Overide */
+/* HPOUT Clamp to GND Override */
#define CS42L42_HPOUT_CLAMP_EN 0
#define CS42L42_HPOUT_CLAMP_DIS 1
* Slot timer must never exceed 85 ms, and must always be at least 25 ms,
* suggested to 75-85 msec by IrDA lite. This doesn't work with a lot of
* devices, and other stackes uses a lot more, so it's best we do it as well
- * (Note : this is the default value and sysctl overides it - Jean II)
+ * (Note : this is the default value and sysctl overrides it - Jean II)
*/
#define SLOT_TIMEOUT (90*HZ/1000)
}
/*
- * When arch-specific code overides this function, the following
+ * When arch-specific code overrides this function, the following
* data should be filled up, assuming stack_trace_max_lock is held to
* prevent concurrent updates.
* stack_trace_index[]
overaall||overall
overhread||overhead
overlaping||overlapping
+overide||override
overrided||overridden
overriden||overridden
overun||overrun
/* Allow writing to any other BAR, or expansion ROM */
iowrite(portoff, val, mask, &d->config_words[reg]);
return true;
- /* We let them overide latency timer and cacheline size */
+ /* We let them override latency timer and cacheline size */
} else if (&d->config_words[reg] == (void *)&d->config.cacheline_size) {
/* Only let them change the first two fields. */
if (mask == 0xFFFFFFFF)
Q = @
endif
-# Disable command line variables (CFLAGS) overide from top
+# Disable command line variables (CFLAGS) override from top
# level Makefile (perf), otherwise build Makefile will get
# the same command line setup.
MAKEOVERRIDES=
Q = @
endif
-# Disable command line variables (CFLAGS) overide from top
+# Disable command line variables (CFLAGS) override from top
# level Makefile (perf), otherwise build Makefile will get
# the same command line setup.
MAKEOVERRIDES=
* struct pevent_plugin_option PEVENT_PLUGIN_OPTIONS[] = {
* {
* .name = "option-name",
- * .plugin_alias = "overide-file-name", (optional)
+ * .plugin_alias = "override-file-name", (optional)
* .description = "description of option to show users",
* },
* {
projects / kernel.git / commitdiff