ath11k: add qcn9074 pci device support

QCN9074 is PCI based 11ax radio.
	- has 2G/5G/6G variants.
	- has NSS 2x2 and 4x4 variants.

QCN9074 uses 45MB of HOST DDR memory, target requests host memory in
segments, each segment is of 2MB size and is physcial contiguous and
use static window configuration.

Currently there are still two issues with QCN9074, see below. So we don't add
QCN9074 PCI id yet to make sure the driver is loaded. The id will be added only
after the issues are fixed.

Issue 1:
 ath11k_pci 0000:06:00.0: qmi failed memory request, err = -110
 ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-110

Issue 2:
 ath11k_pci 0000:06:00.0: firmware crashed: MHI_CB_SYS_ERROR
 ath11k_pci 0000:06:00.0: qmi failed set mode request, mode: 0, err = -110
 ath11k_pci 0000:06:00.0: qmi failed to send wlan fw mode:-110

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-12-git-send-email-akolli@codeaurora.org

diff --git a/drivers/net/wireless/ath/ath11k/pci.c b/drivers/net/wireless/ath/ath11k/pci.c
index 74e4903562511047a1d1bd69b22b50ce3b56373f..0f31eb566fb6bc210c3c6075604314d3379e4849 100644 (file)
--- a/drivers/net/wireless/ath/ath11k/pci.c
+++ b/drivers/net/wireless/ath/ath11k/pci.c
@@ -35,9 +35,11 @@
 #define ACCESS_ALWAYS_OFF 0xFE0
 
 #define QCA6390_DEVICE_ID              0x1101
+#define QCN9074_DEVICE_ID              0x1104
 
 static const struct pci_device_id ath11k_pci_id_table[] = {
        { PCI_VDEVICE(QCOM, QCA6390_DEVICE_ID) },
+       /* TODO: add QCN9074_DEVICE_ID) once firmware issues are resolved */
        {0}
 };
 
@@ -61,6 +63,15 @@ static const struct ath11k_msi_config ath11k_msi_config[] = {
                        { .name = "DP", .num_vectors = 18, .base_vector = 14 },
                },
        },
+       {
+               .total_vectors = 16,
+               .total_users = 3,
+               .users = (struct ath11k_msi_user[]) {
+                       { .name = "MHI", .num_vectors = 3, .base_vector = 0 },
+                       { .name = "CE", .num_vectors = 5, .base_vector = 3 },
+                       { .name = "DP", .num_vectors = 8, .base_vector = 8 },
+               },
+       },
 };
 
 static const char *irq_name[ATH11K_IRQ_NUM_MAX] = {
@@ -1217,6 +1228,12 @@ static int ath11k_pci_probe(struct pci_dev *pdev,
                        ret = -EOPNOTSUPP;
                        goto err_pci_free_region;
                }
+               ab_pci->msi_config = &ath11k_msi_config[0];
+               break;
+       case QCN9074_DEVICE_ID:
+               ab_pci->msi_config = &ath11k_msi_config[1];
+               ab->bus_params.static_window_map = true;
+               ab->hw_rev = ATH11K_HW_QCN9074_HW10;
                break;
        default:
                dev_err(&pdev->dev, "Unknown PCI device found: 0x%x\n",
@@ -1225,7 +1242,6 @@ static int ath11k_pci_probe(struct pci_dev *pdev,
                goto err_pci_free_region;
        }
 
-       ab_pci->msi_config = &ath11k_msi_config[0];
        ret = ath11k_pci_enable_msi(ab_pci);
        if (ret) {
                ath11k_err(ab, "failed to enable msi: %d\n", ret);