dt-bindings: net: sms911x: Convert to json-schema

Convert the Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x
Controller Device Tree binding documentation to json-schema.

Document missing properties.
Make "phy-mode" not required, as many DTS files do not have it, and the
Linux drivers falls back to PHY_INTERFACE_MODE_NA.
Correct nodename in example.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt
index f7da3d73ca1b2e15d71160b9ec811f2aad274e93..32821066a85b0078237cb864cfa1fb23eb814a4f 100644 (file)
--- a/Documentation/devicetree/bindings/net/gpmc-eth.txt
+++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt
@@ -13,7 +13,7 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 For the properties relevant to the ethernet controller connected to the GPMC
 refer to the binding documentation of the device. For example, the documentation
-for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt
+for the SMSC 911x is Documentation/devicetree/bindings/net/smsc,lan9115.yaml
 
 Child nodes need to specify the GPMC bus address width using the "bank-width"
 property but is possible that an ethernet controller also has a property to

diff --git a/Documentation/devicetree/bindings/net/smsc,lan9115.yaml b/Documentation/devicetree/bindings/net/smsc,lan9115.yaml
new file mode 100644 (file)
index 0000000..f86667c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/smsc,lan9115.yaml
@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/smsc,lan9115.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller
+
+maintainers:
+  - Shawn Guo <shawnguo@kernel.org>
+
+allOf:
+  - $ref: ethernet-controller.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - const: smsc,lan9115
+      - items:
+          - enum:
+              - smsc,lan89218
+              - smsc,lan9117
+              - smsc,lan9118
+              - smsc,lan9220
+              - smsc,lan9221
+          - const: smsc,lan9115
+
+  reg:
+    maxItems: 1
+
+  reg-shift: true
+
+  reg-io-width:
+    enum: [ 2, 4 ]
+    default: 2
+
+  interrupts:
+    minItems: 1
+    items:
+      - description:
+          LAN interrupt line
+      - description:
+          Optional PME (power management event) interrupt that is able to wake
+          up the host system with a 50ms pulse on network activity
+
+  clocks:
+    maxItems: 1
+
+  phy-mode: true
+
+  smsc,irq-active-high:
+    type: boolean
+    description: Indicates the IRQ polarity is active-high
+
+  smsc,irq-push-pull:
+    type: boolean
+    description: Indicates the IRQ type is push-pull
+
+  smsc,force-internal-phy:
+    type: boolean
+    description: Forces SMSC LAN controller to use internal PHY
+
+  smsc,force-external-phy:
+    type: boolean
+    description: Forces SMSC LAN controller to use external PHY
+
+  smsc,save-mac-address:
+    type: boolean
+    description:
+      Indicates that MAC address needs to be saved before resetting the
+      controller
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      A GPIO line connected to the RESET (active low) signal of the device.
+      On many systems this is wired high so the device goes out of reset at
+      power-on, but if it is under program control, this optional GPIO can
+      wake up in response to it.
+
+  vdd33a-supply:
+    description: 3.3V analog power supply
+
+  vddvario-supply:
+    description: IO logic power supply
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+# There are lots of bus-specific properties ("qcom,*", "samsung,*", "fsl,*",
+# "gpmc,*", ...) to be found, that actually depend on the compatible value of
+# the parent node.
+additionalProperties: true
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    ethernet@f4000000 {
+            compatible = "smsc,lan9220", "smsc,lan9115";
+            reg = <0xf4000000 0x2000000>;
+            phy-mode = "mii";
+            interrupt-parent = <&gpio1>;
+            interrupts = <31>, <32>;
+            reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+            reg-io-width = <4>;
+            smsc,irq-push-pull;
+    };

diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt
deleted file mode 100644 (file)
index acfafc8..0000000
--- a/Documentation/devicetree/bindings/net/smsc911x.txt
+++ /dev/null
@@ -1,43 +0,0 @@
-* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller
-
-Required properties:
-- compatible : Should be "smsc,lan<model>", "smsc,lan9115"
-- reg : Address and length of the io space for SMSC LAN
-- interrupts : one or two interrupt specifiers
-  - The first interrupt is the SMSC LAN interrupt line
-  - The second interrupt (if present) is the PME (power
-    management event) interrupt that is able to wake up the host
-     system with a 50ms pulse on network activity
-- phy-mode : See ethernet.txt file in the same directory
-
-Optional properties:
-- reg-shift : Specify the quantity to shift the register offsets by
-- reg-io-width : Specify the size (in bytes) of the IO accesses that
-  should be performed on the device.  Valid value for SMSC LAN is
-  2 or 4.  If it's omitted or invalid, the size would be 2.
-- smsc,irq-active-high : Indicates the IRQ polarity is active-high
-- smsc,irq-push-pull : Indicates the IRQ type is push-pull
-- smsc,force-internal-phy : Forces SMSC LAN controller to use
-  internal PHY
-- smsc,force-external-phy : Forces SMSC LAN controller to use
-  external PHY
-- smsc,save-mac-address : Indicates that mac address needs to be saved
-  before resetting the controller
-- reset-gpios : a GPIO line connected to the RESET (active low) signal
-  of the device. On many systems this is wired high so the device goes
-  out of reset at power-on, but if it is under program control, this
-  optional GPIO can wake up in response to it.
-- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies
-
-Examples:
-
-lan9220@f4000000 {
-       compatible = "smsc,lan9220", "smsc,lan9115";
-       reg = <0xf4000000 0x2000000>;
-       phy-mode = "mii";
-       interrupt-parent = <&gpio1>;
-       interrupts = <31>, <32>;
-       reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
-       reg-io-width = <4>;
-       smsc,irq-push-pull;
-};