--- /dev/null
+/*
+ * Device Tree file for Marvell Armada XP maxbcm board
+ *
+ * Copyright (C) 2013-2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+ model = "Marvell Armada XP MAXBCM";
+ compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ /*
+ * 8 GB of plug-in RAM modules by default.The amount
+ * of memory available can be changed by the
+ * bootloader according the size of the module
+ * actually plugged. However, memory between
+ * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
+ * the address range used for I/O (internal registers,
+ * MBus windows).
+ */
+ reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
+ <0x00000001 0x00000000 0x00000001 0x00000000>;
+ };
+
+ cpus {
+ pm_pic {
+ ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>,
+ <&gpio0 17 GPIO_ACTIVE_LOW>,
+ <&gpio0 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 16 MiB */
+ nor@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * The 3 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie@9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie@10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ serial@12000 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+ serial@12100 {
+ status = "okay";
+ };
+ serial@12200 {
+ status = "okay";
+ };
+ serial@12300 {
+ status = "okay";
+ };
+ pinctrl {
+ pinctrl-0 = <&pic_pins>;
+ pinctrl-names = "default";
+ pic_pins: pic-pins-0 {
+ marvell,pins = "mpp16", "mpp17",
+ "mpp18";
+ marvell,function = "gpio";
+ };
+ };
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "sgmii";
+ };
+
+ /* Front-side USB slot */
+ usb@50000 {
+ status = "okay";
+ };
+
+ /* Back-side USB slot */
+ usb@51000 {
+ status = "okay";
+ };
+
+ spi0: spi@10600 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+ };
+
+ nand@d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ };
+ };
+ };
+};
projects / uboot.git / commitdiff