thread_struct's s[12] may contain random kernel memory content, which
may be finally leaked to userspace. This is a security hole. Fix it
by clearing the s[12] array in thread_struct when fork.
As for kthread case, it's better to clear the s[12] array as well.
In the scenario where the macvlan mode is configured as 'source',
macvlan_changelink_sources() will be execured to reconfigure list of
remote source mac addresses, at the same time, if register_netdevice()
return an error, the resource generated by macvlan_changelink_sources()
is not cleaned up.
Using this patch, in the case of an error, it will execute
macvlan_flush_sources() to ensure that the resource is cleaned up.
Fixes: dd9cf0c658bf ("driver: macvlan: Destroy new macvlan port if macvlan_common_newlink failed.") Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Link: https://lore.kernel.org/r/20221109090735.690500-1-nashuiliang@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to init rxq or txq in mv643xx_eth_open() for opening device,
napi isn't disabled. When open mv643xx_eth device next time, it will
trigger a BUG_ON() in napi_enable(). Compile tested only.
Fixes: 88afea138e93 ("mv643xx_eth: get rid of receive-side locking") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221109025432.80900-1-shaozhengchao@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to start nic or add interrupt service routine in
s2io_card_up() for opening device, napi isn't disabled. When open
s2io device next time, it will trigger a BUG_ON()in napi_enable().
Compile tested only.
Fixes: e66a2ac4f99e ("S2io: Fixed synchronization between scheduling of napi with card reset and close") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221109023741.131552-1-shaozhengchao@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When t4vf_update_port_info() failed in cxgb4vf_open(), resources applied
during adapter goes up are not cleared. Fix it. Only be compiled, not be
tested.
Fixes: 10ae9d746d7d ("cxgb4vf: Update port information in cxgb4vf_open()") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221109012100.99132-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to bind qsets in cxgb_up() for opening device, napi isn't
disabled. When open cxgb3 device next time, it will trigger a BUG_ON()
in napi_enable(). Compile tested only.
When failed to create xdp rxqs or fill rx channels in cpsw_ndo_open() for
opening device, napi isn't disabled. When open cpsw device next time, it
will report a invalid opcode issue. Compiled tested only.
For a single CPU system, the kernel thread executing mlx5_cmd_flush()
never releases the CPU but calls down_trylock(&cmd→sem) in a busy loop.
On a single processor system, this leads to a deadlock as the kernel
thread which executes mlx5_cmd_invoke() never gets scheduled. Fix this,
by adding the cond_resched() call to the loop, allow the command
completion kernel thread to execute.
Fixes: 381bd440dd77 ("net/mlx5: Set command entry semaphore up once got index free") Signed-off-by: Alexander Schmidt <alexschm@de.ibm.com> Signed-off-by: Roy Novich <royno@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to enable interrupts in nixge_open() for opening device,
napi isn't disabled. When open nixge device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.
Fixes: 6ac9dc63fb5b ("net: ethernet: nixge: Add support for National Instruments XGE netdev") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221107101443.120205-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
'perf stat' with CSV output option prints an extra empty string as first
field in metrics output line. Sample output below:
# ./perf stat -x, --per-socket -a -C 1 ls
S0,1,1.78,msec,cpu-clock,1785146,100.00,0.973,CPUs utilized
S0,1,26,,context-switches,1781750,100.00,0.015,M/sec
S0,1,1,,cpu-migrations,1780526,100.00,0.561,K/sec
S0,1,1,,page-faults,1779060,100.00,0.561,K/sec
S0,1,875807,,cycles,1769826,100.00,0.491,GHz
S0,1,85281,,stalled-cycles-frontend,1767512,100.00,9.74,frontend cycles idle
S0,1,576839,,stalled-cycles-backend,1766260,100.00,65.86,backend cycles idle
S0,1,288430,,instructions,1762246,100.00,0.33,insn per cycle
====> ,S0,1,,,,,,,2.00,stalled cycles per insn
The above command line uses field separator as "," via "-x," option and
per-socket option displays socket value as first field. But here the
last line for "stalled cycles per insn" has "," in the beginning.
Sample output using interval mode:
# ./perf stat -I 1000 -x, --per-socket -a -C 1 ls
0.001813453,S0,1,1.87,msec,cpu-clock,1872052,100.00,0.002,CPUs utilized
0.001813453,S0,1,2,,context-switches,1868028,100.00,1.070,K/sec
------
0.001813453,S0,1,85379,,instructions,1856754,100.00,0.32,insn per cycle
====> 0.001813453,,S0,1,,,,,,,1.34,stalled cycles per insn
Above result also has an extra CSV separator after
the timestamp. Patch addresses extra field separator
in the beginning of the metric output line.
The counter stats are displayed by function
"perf_stat__print_shadow_stats" in code
"util/stat-shadow.c". While printing the stats info
for "stalled cycles per insn", function "new_line_csv"
is used as new_line callback.
The new_line_csv function has check for "os->prefix"
and if prefix is not null, it will be printed along
with cvs separator.
Snippet from "new_line_csv":
if (os->prefix)
fprintf(os->fh, "%s%s", os->prefix, config->csv_sep);
Here os->prefix gets printed followed by ","
which is the cvs separator. The os->prefix is
used in interval mode option ( -I ), to print
time stamp on every new line. But prefix is
already set to contain CSV separator when used
in interval mode for CSV option.
Also if prefix is not assigned (if not used with
-I option), it gets set to empty string.
Reference: function printout() in util/stat-display.c
Snippet:
.prefix = prefix ? prefix : "",
Since prefix already set to contain cvs_sep in interval
option, patch removes printing config->csv_sep in
new_line_csv function to avoid printing extra field.
After the patch:
# ./perf stat -x, --per-socket -a -C 1 ls
S0,1,2.04,msec,cpu-clock,2045202,100.00,1.013,CPUs utilized
S0,1,2,,context-switches,2041444,100.00,979.289,/sec
S0,1,0,,cpu-migrations,2040820,100.00,0.000,/sec
S0,1,2,,page-faults,2040288,100.00,979.289,/sec
S0,1,254589,,cycles,2036066,100.00,0.125,GHz
S0,1,82481,,stalled-cycles-frontend,2032420,100.00,32.40,frontend cycles idle
S0,1,113170,,stalled-cycles-backend,2031722,100.00,44.45,backend cycles idle
S0,1,88766,,instructions,2030942,100.00,0.35,insn per cycle
S0,1,,,,,,,1.27,stalled cycles per insn
Fixes: a84cf0d99fb28ff2 ("perf stat: Implement CSV metrics output") Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com> Reviewed-By: Kajol Jain <kjain@linux.ibm.com> Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com> Tested-by: Disha Goel <disgoel@linux.vnet.ibm.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nageswara R Sastry <rnsastry@linux.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20221018085605.63834-1-atrajeev@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to register irq in xgene_enet_open() for opening device,
napi isn't disabled. When open xgene device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.
The first IRQ is required, but IRQs 1 through (nb_phy_chans - 1) are
optional, because on some platforms (e.g. PXA168) there is a single IRQ
shared between all channels.
This change inhibits a flood of "IRQ index # not found" messages at
startup. Tested on a PXA168-based device.
Fixes: 682a742ed79d ("driver core: platform: Add an error message to platform_get_irq*()") Signed-off-by: Doug Brown <doug@schmorgal.com> Link: https://lore.kernel.org/r/20220906000709.52705-1-doug@schmorgal.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a follow-up for commit a34138279b29 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.
It causes NULL pointer dereference when testing as following:
(a) use syscall(__NR_socket, 0x10ul, 3ul, 0) to create netlink socket.
(b) use syscall(__NR_sendmsg, ...) to create bond link device and vxcan
link device, and bind vxcan device to bond device (can also use
ifenslave command to bind vxcan device to bond device).
(c) use syscall(__NR_socket, 0x1dul, 3ul, 1) to create CAN socket.
(d) use syscall(__NR_bind, ...) to bind the bond device to CAN socket.
The bond device invokes the can-raw protocol registration interface to
receive CAN packets. However, ml_priv is not allocated to the dev,
dev_rcv_lists is assigned to NULL in can_rx_register(). In this case,
it will occur the NULL pointer dereference issue.
The following is the stack information:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 122a4067 P4D 122a4067 PUD 1223c067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
RIP: 0010:can_rx_register+0x12d/0x1e0
Call Trace:
<TASK>
raw_enable_filters+0x8d/0x120
raw_enable_allfilters+0x3b/0x130
raw_bind+0x118/0x4f0
__sys_bind+0x163/0x1a0
__x64_sys_bind+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 89493ac6383b ("net: introduce CAN specific pointer in the struct net_device") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/all/20221028085650.170470-1-shaozhengchao@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch ensures that the reserved field is always initialized.
Reported-by: syzbot+3553517af6020c4f2813f1003fe76ef3cbffe98d@syzkaller.appspotmail.com Fixes: 50b1de658254 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.") Signed-off-by: Alexander Potapenko <glider@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A problem about modprobe vc4 failed is triggered with the following log
given:
[ 420.327987] Error: Driver 'vc4_hvs' is already registered, aborting...
[ 420.333904] failed to register platform driver vc4_hvs_driver [vc4]: -16
modprobe: ERROR: could not insert 'vc4': Device or resource busy
The reason is that vc4_drm_register() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
fails, it returns without unregistering all the vc4 drivers, resulting the
vc4 can never be installed later.
A simple call graph is shown as below:
vc4_drm_register()
platform_register_drivers() # all vc4 drivers are registered
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without unregister drivers
Fixing this problem by checking the return value of
platform_driver_register() and do platform_unregister_drivers() if
error happened.
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, bpq_device_event() receives the message
and creates a new bpq device. In this case, the reference count value of
dev is hold once. But after "ifenslave -f bond2 rose1" command is
executed, the type of the bond device is changed to rose. When the bond
device is unregistered, bpq_device_event() will not put the dev reference
count.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, lapbeth_device_event() receives the
message and creates a new lapbeth device. In this case, the reference
count value of dev is hold once. But after "ifenslave -f bond2 rose1"
command is executed, the type of the bond device is changed to rose. When
the bond device is unregistered, lapbeth_device_event() will not put the
dev reference count.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in security/commoncap.c:1252:2
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
cap_task_prctl+0x561/0x6f0
security_task_prctl+0x5a/0xb0
__x64_sys_prctl+0x61/0x8f0
do_syscall_64+0x58/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 59bf6ceeb8d1 ("Add 64-bit capability support to the kernel") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Reviewed-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the mac device gets removed, it leaves behind the ethernet device.
This will result in a segfault next time the ethernet device accesses
mac_dev. Remove the ethernet device when we get removed to prevent
this. This is not completely reversible, since some resources aren't
cleaned up properly, but that can be addressed later.
In the bnxt_en driver ndo_rx_flow_steer returns '0' whenever an entry
that we are attempting to steer is already found. This is not the
correct behavior. The return code should be the value/index that
corresponds to the entry. Returning zero all the time causes the
RFS records to be incorrect unless entry '0' is the correct one. As
flows migrate to different cores this can create entries that are not
correct.
Fixes: dfe047769e71 ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Akshay Navgire <anavgire@purestorage.com> Signed-off-by: Alex Barba <alex.barba@broadcom.com> Signed-off-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During the error recovery sequence, the rtnl_lock is not held for the
entire duration and some datastructures may be freed during the sequence.
Check for the BNXT_STATE_OPEN flag instead of netif_running() to ensure
that the device is fully operational before proceeding to reconfigure
the coalescing settings.
The issue occurs in the following scenarios:
tun_get_user()
napi_gro_frags()
napi_frags_finish()
case GRO_NORMAL:
gro_normal_one()
list_add_tail(&skb->list, &napi->rx_list);
<-- While napi->rx_count < READ_ONCE(gro_normal_batch),
<-- gro_normal_list() is not called, napi->rx_list is not empty
<-- not ask to complete the gro work, will cause memory leaks in
<-- following tun_napi_del()
...
tun_napi_del()
netif_napi_del()
__netif_napi_del()
<-- &napi->rx_list is not empty, which caused memory leaks
To fix, add napi_complete() after napi_gro_frags().
Fixes: 12d2dcce0caa ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit ffb6eacc0ec6 ("net: gso: Fix skb_segment splat when
splitting gso_size mangled skb having linear-headed frag_list"), it is
allowed to change gso_size of a GRO packet. However, that commit assumes
that "checking the first list_skb member suffices; i.e if either of the
list_skb members have non head_frag head, then the first one has too".
It turns out this assumption does not hold. We've seen BUG_ON being hit
in skb_segment when skbs on the frag_list had differing head_frag with
the vmxnet3 driver. This happens because __netdev_alloc_skb and
__napi_alloc_skb can return a skb that is page backed or kmalloced
depending on the requested size. As the result, the last small skb in
the GRO packet can be kmalloced.
There are three different locations where this can be fixed:
(1) We could check head_frag in GRO and not allow GROing skbs with
different head_frag. However, that would lead to performance
regression on normal forward paths with unmodified gso_size, where
!head_frag in the last packet is not a problem.
(2) Set a flag in bpf_skb_net_grow and bpf_skb_net_shrink indicating
that NETIF_F_SG is undesirable. That would need to eat a bit in
sk_buff. Furthermore, that flag can be unset when all skbs on the
frag_list are page backed. To retain good performance,
bpf_skb_net_grow/shrink would have to walk the frag_list.
(3) Walk the frag_list in skb_segment when determining whether
NETIF_F_SG should be cleared. This of course slows things down.
This patch implements (3). To limit the performance impact in
skb_segment, the list is walked only for skbs with SKB_GSO_DODGY set
that have gso_size changed. Normal paths thus will not hit it.
We could check only the last skb but since we need to walk the whole
list anyway, let's stay on the safe side.
Fixes: ffb6eacc0ec6 ("net: gso: Fix skb_segment splat when splitting gso_size mangled skb having linear-headed frag_list") Signed-off-by: Jiri Benc <jbenc@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/e04426a6a91baf4d1081e1b478c82b5de25fdf21.1667407944.git.jbenc@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root case is in commit d40c2cfef144 ("bpf, sockmap: Fix more uncharged
while msg has more_data"), where I used msg->sg.size to replace the tosend,
causing breakage:
if (msg->apply_bytes && msg->apply_bytes < tosend)
tosend = psock->apply_bytes;
Fixes: d40c2cfef144 ("bpf, sockmap: Fix more uncharged while msg has more_data") Reported-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/1667266296-8794-1-git-send-email-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function query_regdb_file() the alpha2 parameter is duplicated
using kmemdup() and subsequently freed in regdb_fw_cb(). However,
request_firmware_nowait() can fail without calling regdb_fw_cb() and
thus leak memory.
Fixes: 2620d354427f ("cfg80211: support loading regulatory database as firmware file") Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All we're going to do with this pointer is assign it to
another __rcu pointer, but sparse can't see that, so
use rcu_access_pointer() to silence the warning here.
Fixes: cede852d4c24 ("wifi: cfg80211: update hidden BSSes to avoid WARN_ON") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xfsaild is racy with respect to transaction abort and shutdown in
that the task can idle or exit with an empty AIL but buffers still
on the delwri queue. This was partly addressed by cancelling the
delwri queue before the task exits to prevent memory leaks, but it's
also possible for xfsaild to empty and idle with buffers on the
delwri queue. For example, a transaction that pins a buffer that
also happens to sit on the AIL delwri queue will explicitly remove
the associated log item from the AIL if the transaction aborts. The
side effect of this is an unmount hang in xfs_wait_buftarg() as the
associated buffers remain held by the delwri queue indefinitely.
This is reproduced on repeated runs of generic/531 with an fs format
(-mrmapbt=1 -bsize=1k) that happens to also reproduce transaction
aborts.
Update xfsaild to not idle until both the AIL and associated delwri
queue are empty and update the push code to continue delwri queue
submission attempts even when the AIL is empty. This allows the AIL
to eventually release aborted buffers stranded on the delwri queue
when they are unlocked by the associated transaction. This should
have no significant effect on normal runtime behavior because the
xfsaild currently idles only when the AIL is empty and in practice
the AIL is rarely empty with a populated delwri queue. The items
must be AIL resident to land in the queue in the first place and
generally aren't removed until writeback completes.
Note that the pre-existing delwri queue cancel logic in the exit
path is retained because task stop is external, could technically
come at any point, and xfsaild is still responsible to release its
buffer references before it exits.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ For 5.4.y, SB_I_VERSION should be set in xfs_fs_remount() ]
The MS_I_VERSION mount flag is exposed via the VFS, as documented
in the mount manpages etc; see the iversion and noiversion mount
options in mount(8).
As a result, mount -o remount looks for this option in /proc/mounts
and will only send the I_VERSION flag back in during remount it it
is present. Since it's not there, a remount will /remove/ the
I_VERSION flag at the vfs level, and iversion functionality is lost.
xfs v5 superblocks intend to always have i_version enabled; it is
set as a default at mount time, but is lost during remount for the
reasons above.
The generic fix would be to expose this documented option in
/proc/mounts, but since that was rejected, fix it up again in the
xfs remount path instead, so that at least xfs won't suffer from
this misbehavior.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page faultround path ->map_pages is implemented in XFS via
filemap_map_pages(). This function checks that pages found in page
cache lookups have not raced with truncate based invalidation by
checking page->mapping is correct and page->index is within EOF.
However, we've known for a long time that this is not sufficient to
protect against races with invalidations done by operations that do
not change EOF. e.g. hole punching and other fallocate() based
direct extent manipulations. The way we protect against these
races is we wrap the page fault operations in a XFS_MMAPLOCK_SHARED
lock so they serialise against fallocate and truncate before calling
into the filemap function that processes the fault.
Do the same for XFS's ->map_pages implementation to close this
potential data corruption issue.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing reflink remapping loop has some structural problems that
need addressing:
The biggest problem is that we create one transaction for each extent in
the source file without accounting for the number of mappings there are
for the same range in the destination file. In other words, we don't
know the number of remap operations that will be necessary and we
therefore cannot guess the block reservation required. On highly
fragmented filesystems (e.g. ones with active dedupe) we guess wrong,
run out of block reservation, and fail.
The second problem is that we don't actually use the bmap intents to
their full potential -- instead of calling bunmapi directly and having
to deal with its backwards operation, we could call the deferred ops
xfs_bmap_unmap_extent and xfs_refcount_decrease_extent instead. This
makes the frontend loop much simpler.
Solve all of these problems by refactoring the remapping loops so that
we only perform one remapping operation per transaction, and each
operation only tries to remap a single extent from source to dest.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reported-by: Edwin Török <edwin@etorok.net> Tested-by: Edwin Török <edwin@etorok.net> Acked-by: Darrick J. Wong <djwong@kernel.org>
[backported to 5.4.y - Tested-by above does not refer to the backport] Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of this predicate is a little misleading -- it decides if the
extent mapping is allocated and written. Change the name to be more
direct, as we're going to add a new predicate in the next patch.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Slightly modify xfs_trans_alloc() to fix a merge conflict due to missing
"atomic_inc(&mp->m_active_trans)" statement in v5.9 kernel]
The rmapbt extent swap algorithm remaps individual extents between
the source inode and the target to trigger reverse mapping metadata
updates. If either inode straddles a format or other bmap allocation
boundary, the individual unmap and map cycles can trigger repeated
bmap block allocations and frees as the extent count bounces back
and forth across the boundary. While net block usage is bound across
the swap operation, this behavior can prematurely exhaust the
transaction block reservation because it continuously drains as the
transaction rolls. Each allocation accounts against the reservation
and each free returns to global free space on transaction roll.
The previous workaround to this problem attempted to detect this
boundary condition and provide surplus block reservation to
acommodate it. This is insufficient because more remaps can occur
than implied by the extent counts; if start offset boundaries are
not aligned between the two inodes, for example.
To address this problem more generically and dynamically, add a
transaction accounting mode that returns freed blocks to the
transaction reservation instead of the superblock counters on
transaction roll and use it when the rmapbt based algorithm is
active. This allows the chain of remap transactions to preserve the
block reservation based own its own frees and prevent premature
exhaustion regardless of the remap pattern. Note that this is only
safe for superblocks with lazy sb accounting, but the latter is
required for v5 supers and the rmap feature depends on v5.
Fixes: 5351e893c3ef3 ("xfs: account format bouncing into rmapbt swapext tx reservation") Root-caused-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus proposes to revert an accounting for sops objects in
do_semtimedop() because it's really just a temporary buffer
for a single semtimedop() system call.
This object can consume up to 2 pages, syscall is sleeping
one, size and duration can be controlled by user, and this
allocation can be repeated by many thread at the same time.
However Shakeel Butt pointed that there are much more popular
objects with the same life time and similar memory
consumption, the accounting of which was decided to be
rejected for performance reasons.
Considering at least 2 pages for task_struct and 2 pages for
the kernel stack, a back of the envelope calculation gives a
footprint amplification of <1.5 so this temporal buffer can be
safely ignored.
The factor would IMO be interesting if it was >> 2 (from the
PoV of excessive (ab)use, fine-grained accounting seems to be
currently unfeasible due to performance impact).
This patch fixes an intra-object buffer overflow in brcmfmac that occurs
when the device provides a 'bsscfgidx' equal to or greater than the
buffer size. The patch adds a check that leads to a safe failure if that
is the case.
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Reviewed-by: Arend van Spriel <aspriel@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dokyung Song <dokyung.song@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221021061359.GA550858@laguna Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call intel_sdvo_select_ddc_bus() before initializing any
of the outputs. And before that is functional (assuming no VBT)
we have to set up the controlled_outputs thing. Otherwise DDC
won't be functional during the output init but LVDS really
needs it for the fixed mode setup.
Note that the whole multi output support still looks very
bogus, and more work will be needed to make it correct.
But for now this should at least fix the LVDS EDID fixed mode
setup.
Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7301 Fixes: 305b97439b64 ("drm/i915/sdvo: Fix multi function encoder stuff") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-3-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 8ab705859698d8ee6f24b62a71824f43b62caf8c) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We try to filter out the corresponding xxx1 output
if the xxx0 output is not present. But the way that is
being done is pretty awkward. Make it less so.
We can't safely probe a dual-DSI display asynchronously
(driver_async_probe='*' or driver_async_probe='dw-mipi-dsi-rockchip'
cmdline), because dw_mipi_dsi_rockchip_find_second() pokes one DSI
device's drvdata from the other device without any locking.
Request synchronous probe, at least until this driver learns some
appropriate locking for dual-DSI initialization.
a4c43507bccef Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in a4c43507bccef is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: a4c43507bccef ("mtd: rawnand: gpmi: Fix setting busy timeout setting") Fixes: 16c1b23db3788 ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Han Xu <han.xu@nxp.com> Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the emulation mode when handling writes to CR0, because
toggling CR0.PE switches between Real and Protected Mode, and toggling
CR0.PG when EFER.LME=1 switches between Long and Protected Mode.
This is likely a benign bug because there is no writeback of state,
other than the RIP increment, and when toggling CR0.PE, the CPU has
to execute code from a very low memory address.
Some instructions update the cpu execution mode, which needs to update the
emulation mode.
Extract this code, and make assign_eip_far use it.
assign_eip_far now reads CS, instead of getting it via a parameter,
which is ok, because callers always assign CS to the same value
before calling this function.
SYSEXIT is one of the instructions that can change the
processor mode, thus ctxt->mode should be updated after it.
Note that this is likely a benign bug, because the only problematic
mode change is from 32 bit to 64 bit which can lead to truncation of RIP,
and it is not possible to do with sysexit,
since sysexit running in 32 bit mode will be limited to 32 bit version.
KVM_GET_SUPPORTED_CPUID should only enumerate features that KVM
actually supports. The following ranges of CPUID.80000008H are reserved
and should be masked off:
ECX[31:18]
ECX[11:8]
In addition, the PerfTscSize field at ECX[17:16] should also be zero
because KVM does not set the PERFTSC bit at CPUID.80000001H.ECX[27].
KVM_GET_SUPPORTED_CPUID should only enumerate features that KVM
actually supports. In the case of CPUID.8000001AH, only three bits are
currently defined. The 125 reserved bits should be masked off.
The rec_len field in the directory entry has to be a multiple of 4. A
corrupted filesystem image can be used to hit a BUG() in
ext4_rec_len_to_disk(), called from make_indexed_dir().
Avoid that the hardware path is shown twice in the kernel log, and clean
up the output of the version numbers to show up in the same order as
they are listed in the hardware database in the hardware.c file.
Additionally, optimize the memory footprint of the hardware database
and mark some code as init code.
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
The intel_pebs_isolation quirk checks both model number and stepping.
Cooper Lake has a different stepping (11) than the other Skylake Xeon.
It cannot benefit from the optimization in commit 52065cbf12293
("perf/x86/kvm: Avoid unnecessary work in guest filtering").
Add the stepping of Cooper Lake into the isolation_ucodes[] table.
We no longer need at least 64 bytes of random seed to permit the early
crng init to complete. The RNG is now based on Blake2s, so reduce the
EFI seed size to the Blake2s hash size, which is sufficient for our
purposes.
While at it, drop the READ_ONCE(), which was supposed to prevent size
from being evaluated after seed was unmapped. However, this cannot
actually happen, so READ_ONCE() is unnecessary here.
In cap_inode_getsecurity(), we will use vfs_getxattr_alloc() to
complete the memory allocation of tmpbuf, if we have completed
the memory allocation of tmpbuf, but failed to call handler->get(...),
there will be a memleak in below logic:
|-- ret = (int)vfs_getxattr_alloc(mnt_userns, ...)
| /* ^^^ alloc for tmpbuf */
|-- value = krealloc(*xattr_value, error + 1, flags)
| /* ^^^ alloc memory */
|-- error = handler->get(handler, ...)
| /* error! */
|-- *xattr_value = value
| /* xattr_value is &tmpbuf (memory leak!) */
So we will try to free(tmpbuf) after vfs_getxattr_alloc() fails to fix it.
Cc: stable@vger.kernel.org Fixes: 8e3c7cc45997 ("Introduce v3 namespaced file capabilities") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Acked-by: Serge Hallyn <serge@hallyn.com>
[PM: subject line and backtrace tweaks] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The C standard says that memcmp() must treat the buffers as consisting
of "unsigned chars". If char happens to be unsigned, the casts are ok,
but then obviously the c1 variable can never contain a negative
value. And when char is signed, the casts are wrong, and there's still
a problem with using an 8-bit quantity to hold the difference, because
that can range from -255 to +255.
For example, assuming char is signed, comparing two 1-byte buffers,
one containing 0x00 and another 0x80, the current implementation would
return -128 for both memcmp(a, b, 1) and memcmp(b, a, 1), whereas one
of those should of course return something positive.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Fixes: 6c9adb75b7b3 ("rcutorture: Import a copy of nolibc") Cc: stable@vger.kernel.org # v5.0+ Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In aggregate kprobe case, when arm_kprobe failed,
we need set the kp->flags with KPROBE_FLAG_DISABLED again.
If not, the 'kp' kprobe will been considered as enabled
but it actually not enabled.
Commit 1c00118470cf ("ipv4: namespacify ip_early_demux sysctl knob") made
it possible to enable/disable early_demux on a per-netns basis. Then, we
introduced two knobs, tcp_early_demux and udp_early_demux, to switch it for
TCP/UDP in commit bb245b2f9d37 ("net: Add sysctl to toggle early demux for
tcp and udp"). However, the .proc_handler() was wrong and actually
disabled us from changing the behaviour in each netns.
We can execute early_demux if net.ipv4.ip_early_demux is on and each proto
.early_demux() handler is not NULL. When we toggle (tcp|udp)_early_demux,
the change itself is saved in each netns variable, but the .early_demux()
handler is a global variable, so the handler is switched based on the
init_net's sysctl variable. Thus, netns (tcp|udp)_early_demux knobs have
nothing to do with the logic. Whether we CAN execute proto .early_demux()
is always decided by init_net's sysctl knob, and whether we DO it or not is
by each netns ip_early_demux knob.
This patch namespacifies (tcp|udp)_early_demux again. For now, the users
of the .early_demux() handler are TCP and UDP only, and they are called
directly to avoid retpoline. So, we can remove the .early_demux() handler
from inet6?_protos and need not dereference them in ip6?_rcv_finish_core().
If another proto needs .early_demux(), we can restore it at that time.
Fixes: bb245b2f9d37 ("net: Add sysctl to toggle early demux for tcp and udp") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20220713175207.7727-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The type of parameter generation has been u32 since the beginning,
however all callers pass a u64 generation, so unify the types to prevent
potential loss.
CC: stable@vger.kernel.org # 4.9+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Carlos Llamas [Fri, 4 Nov 2022 17:55:33 +0000 (17:55 +0000)]
binder: fix UAF of alloc->vma in race with munmap()
In commit d5e731de6f24 ("ANDROID: binder: change down_write to
down_read") binder assumed the mmap read lock is sufficient to protect
alloc->vma inside binder_update_page_range(). This used to be accurate
until commit 4dc981eb15b2 ("mm: mmap: zap pages with read mmap_sem in
munmap"), which now downgrades the mmap_lock after detaching the vma
from the rbtree in munmap(). Then it proceeds to teardown and free the
vma with only the read lock held.
This means that accesses to alloc->vma in binder_update_page_range() now
will race with vm_area_free() in munmap() and can cause a UAF as shown
in the following KASAN trace:
==================================================================
BUG: KASAN: use-after-free in vm_insert_page+0x7c/0x1f0
Read of size 8 at addr ffff16204ad00600 by task server/558
To prevent the race above, revert back to taking the mmap write lock
inside binder_update_page_range(). One might expect an increase of mmap
lock contention. However, binder already serializes these calls via top
level alloc->mutex. Also, there was no performance impact shown when
running the binder benchmark tests.
Note this patch is specific to stable branches 5.4 and 5.10. Since in
newer kernel releases binder no longer caches a pointer to the vma.
Instead, it has been refactored to use vma_lookup() which avoids the
issue described here. This switch was introduced in commit ef637881249e
("android: binder: stop saving a pointer to the VMA").
Fixes: 4dc981eb15b2 ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Cc: <stable@vger.kernel.org> # 5.4.x Cc: Minchan Kim <minchan@kernel.org> Cc: Yang Shi <yang.shi@linux.alibaba.com> Cc: Liam Howlett <liam.howlett@oracle.com> Signed-off-by: Carlos Llamas <cmllamas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a memory leak [0] related to IPV6_ADDRFORM.
The scenario is that while one thread is converting an IPv6 socket into
IPv4 with IPV6_ADDRFORM, another thread calls do_ipv6_setsockopt() and
allocates memory to inet6_sk(sk)->XXX after conversion.
Then, the converted sk with (tcp|udp)_prot never frees the IPv6 resources,
which inet6_destroy_sock() should have cleaned up.
setsockopt(IPV6_ADDRFORM) setsockopt(IPV6_DSTOPTS)
+-----------------------+ +----------------------+
- do_ipv6_setsockopt(sk, ...)
- sockopt_lock_sock(sk) - do_ipv6_setsockopt(sk, ...)
- lock_sock(sk) ^._ called via tcpv6_prot
- WRITE_ONCE(sk->sk_prot, &tcp_prot) before WRITE_ONCE()
- xchg(&np->opt, NULL)
- txopt_put(opt)
- sockopt_release_sock(sk)
- release_sock(sk) - sockopt_lock_sock(sk)
- lock_sock(sk)
- ipv6_set_opt_hdr(sk, ...)
- ipv6_update_options(sk, opt)
- xchg(&inet6_sk(sk)->opt, opt)
^._ opt is never freed.
- sockopt_release_sock(sk)
- release_sock(sk)
Since IPV6_DSTOPTS allocates options under lock_sock(), we can avoid this
memory leak by testing whether sk_family is changed by IPV6_ADDRFORM after
acquiring the lock.
This issue exists from the initial commit between IPV6_ADDRFORM and
IPV6_PKTOPTIONS.
If bfq_schedule_dispatch() is called from bfq_idle_slice_timer_body(),
then 'bfqd->queued' is read without holding 'bfqd->lock'. This is
wrong since it can be wrote concurrently.
Fix the problem by holding 'bfqd->lock' in such case.
xfs_ifree_cluster() calls xfs_perag_get() at the beginning, but forgets to
call xfs_perag_put() in one failed path.
Add the missed function call to fix it.
Fixes: 145b69e6f339 ("xfs: make xfs_trans_get_buf return an error code") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During writeback, it's possible for the quota block reservation in
xfs_iomap_write_unwritten to fail with EDQUOT because we hit the quota
limit. This causes writeback errors for data that was already written
to disk, when it's not even guaranteed that the bmbt will expand to
exceed the quota limit. Irritatingly, this condition is reported to
userspace as EIO by fsync, which is confusing.
We wrote the data, so allow the reservation. That might put us slightly
above the hard limit, but it's better than losing data after a write.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Long ago, group & project quota were mutually exclusive, and so
when we turned on XFS_QMOPT_ENOSPC ("return ENOSPC if project quota
is exceeded") when project quota was enabled, we only needed to
disable it again for user quota.
When group & project quota got separated, this got missed, and as a
result if project quota is enabled and group quota is exceeded, the
error code returned is incorrectly returned as ENOSPC not EDQUOT.
Fix this by stripping XFS_QMOPT_ENOSPC out of flags for group
quota when we try to reserve the space.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error handling in xfs_trans_unreserve_and_mod_sb() is largely
incorrect - rolling back the changes in the transaction if only one
counter underruns makes all the other counters incorrect. We still
allow the change to proceed and committing the transaction, except
now we have multiple incorrect counters instead of a single
underflow.
Further, we don't actually report the error to the caller, so this
is completely silent except on debug kernels that will assert on
failure before we even get to the rollback code. Hence this error
handling is broken, untested, and largely unnecessary complexity.
Just remove it.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While QAing the new xfs_repair quotacheck code, I uncovered a quota
corruption bug resulting from a bad interaction between dquot buffer
initialization and quotacheck. The bug can be reproduced with the
following sequence:
# mkfs.xfs -f /dev/sdf
# mount /dev/sdf /opt -o usrquota
# su nobody -s /bin/bash -c 'touch /opt/barf'
# sync
# xfs_quota -x -c 'report -ahi' /opt
User quota on /opt (/dev/sdf)
Inodes
User ID Used Soft Hard Warn/Grace
---------- ---------------------------------
root 3 0 0 00 [------]
nobody 1 0 0 00 [------]
# xfs_io -x -c 'shutdown' /opt
# umount /opt
# mount /dev/sdf /opt -o usrquota
# touch /opt/man2
# xfs_quota -x -c 'report -ahi' /opt
User quota on /opt (/dev/sdf)
Inodes
User ID Used Soft Hard Warn/Grace
---------- ---------------------------------
root 1 0 0 00 [------]
nobody 1 0 0 00 [------]
# umount /opt
Notice how the initial quotacheck set the root dquot icount to 3
(rootino, rbmino, rsumino), but after shutdown -> remount -> recovery,
xfs_quota reports that the root dquot has only 1 icount. We haven't
deleted anything from the filesystem, which means that quota is now
under-counting. This behavior is not limited to icount or the root
dquot, but this is the shortest reproducer.
I traced the cause of this discrepancy to the way that we handle ondisk
dquot updates during quotacheck vs. regular fs activity. Normally, when
we allocate a disk block for a dquot, we log the buffer as a regular
(dquot) buffer. Subsequent updates to the dquots backed by that block
are done via separate dquot log item updates, which means that they
depend on the logged buffer update being written to disk before the
dquot items. Because individual dquots have their own LSN fields, that
initial dquot buffer must always be recovered.
However, the story changes for quotacheck, which can cause dquot block
allocations but persists the final dquot counter values via a delwri
list. Because recovery doesn't gate dquot buffer replay on an LSN, this
means that the initial dquot buffer can be replayed over the (newer)
contents that were delwritten at the end of quotacheck. In effect, this
re-initializes the dquot counters after they've been updated. If the
log does not contain any other dquot items to recover, the obsolete
dquot contents will not be corrected by log recovery.
Because quotacheck uses a transaction to log the setting of the CHKD
flags in the superblock, we skip quotacheck during the second mount
call, which allows the incorrect icount to remain.
Fix this by changing the ondisk dquot initialization function to use
ordered buffers to write out fresh dquot blocks if it detects that we're
running quotacheck. If the system goes down before quotacheck can
complete, the CHKD flags will not be set in the superblock and the next
mount will run quotacheck again, which can fix uninitialized dquot
buffers. This requires amending the defer code to maintaine ordered
buffer state across defer rolls for the sake of the dquot allocation
code.
For regular operations we preserve the current behavior since the dquot
items require properly initialized ondisk dquot records.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attr fork can transition from shortform to leaf format while
empty if the first xattr doesn't fit in shortform. While this empty
leaf block state is intended to be transient, it is technically not
due to the transactional implementation of the xattr set operation.
We historically have a couple of bandaids to work around this
problem. The first is to hold the buffer after the format conversion
to prevent premature writeback of the empty leaf buffer and the
second is to bypass the xattr count check in the verifier during
recovery. The latter assumes that the xattr set is also in the log
and will be recovered into the buffer soon after the empty leaf
buffer is reconstructed. This is not guaranteed, however.
If the filesystem crashes after the format conversion but before the
xattr set that induced it, only the format conversion may exist in
the log. When recovered, this creates a latent corrupted state on
the inode as any subsequent attempts to read the buffer fail due to
verifier failure. This includes further attempts to set xattrs on
the inode or attempts to destroy the attr fork, which prevents the
inode from ever being removed from the unlinked list.
To avoid this condition, accept that an empty attr leaf block is a
valid state and remove the count check from the verifier. This means
that on rare occasions an attr fork might exist in an unexpected
state, but is otherwise consistent and functional. Note that we
retain the logic to avoid racing with metadata writeback to reduce
the window where this can occur.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can currently write to sysfs to transition sdev_state to RUNNING
or OFFLINE from any source state. This causes issues because proper
transitioning out of some states involves steps besides just changing
sdev_state, so allowing userspace to change sdev_state regardless of the
source state can result in inconsistencies; e.g. with ISCSI we can end up
with sdev_state == SDEV_RUNNING while the device queue is quiesced. Any
task attempting I/O on the device will then hang, and in more recent
kernels, iscsid will hang as well.
More detail about this bug is provided in my first attempt:
drivers/media/dvb-frontends/drxk_hard.c: In function 'drxk_read_ucblocks':
drivers/media/dvb-frontends/drxk_hard.c:6673:21: warning: 'err' may be used uninitialized [-Wmaybe-uninitialized]
6673 | *ucblocks = (u32) err;
| ^~~~~~~~~
drivers/media/dvb-frontends/drxk_hard.c:6663:13: note: 'err' was declared here
6663 | u16 err;
| ^~~
During the initialization of ip6_route_net_init_late(), if file
ipv6_route or rt6_stats fails to be created, the initialization is
successful by default. Therefore, the ipv6_route or rt6_stats file
doesn't be found during the remove in ip6_route_net_exit_late(). It
will cause WRNING.
The following is the stack information:
name 'rt6_stats'
WARNING: CPU: 0 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
PKRU: 55555554
Call Trace:
<TASK>
ops_exit_list+0xb0/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 616ce96eee63 ("[NETNS][IPV6] route6 - create route6 proc files for the namespace") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20221102020610.351330-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix it by passing NULL to pneigh_queue_purge() in neigh_ifdown() if dev
is NULL, to make kernel not panic immediately.
Fixes: a6b7801f2c1e ("neigh: fix possible DoS due to net iface start/stop loop") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Denis V. Lunev <den@openvz.org> Link: https://lore.kernel.org/r/20221101121552.21890-1-chenzhongjin@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in drivers/net/phy/mdio_bus.c:586:27
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
__mdiobus_register+0x49d/0x4e0
fixed_mdio_bus_init+0xd8/0x12d
do_one_initcall+0x76/0x430
kernel_init_freeable+0x3b3/0x422
kernel_init+0x24/0x1e0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 7dc00a7d0f34 ("phylib: allow incremental scanning of an mii bus") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221031132645.168421-1-cuigaosheng1@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When l2cap_recv_frame() is invoked to receive data, and the cid is
L2CAP_CID_A2MP, if the channel does not exist, it will create a channel.
However, after a channel is created, the hold operation of the channel
is not performed. In this case, the value of channel reference counting
is 1. As a result, after hci_error_reset() is triggered, l2cap_conn_del()
invokes the close hook function of A2MP to release the channel. Then
l2cap_chan_unlock(chan) will trigger UAF issue.
The process is as follows:
Receive data:
l2cap_data_channel()
a2mp_channel_create() --->channel ref is 2
l2cap_chan_put() --->channel ref is 1
Triger event:
hci_error_reset()
hci_dev_do_close()
...
l2cap_disconn_cfm()
l2cap_conn_del()
l2cap_chan_hold() --->channel ref is 2
l2cap_chan_del() --->channel ref is 1
a2mp_chan_close_cb() --->channel ref is 0, release channel
l2cap_chan_unlock() --->UAF of channel
The detailed Call Trace is as follows:
BUG: KASAN: use-after-free in __mutex_unlock_slowpath+0xa6/0x5e0
Read of size 8 at addr ffff8880160664b8 by task kworker/u11:1/7593
Workqueue: hci0 hci_error_reset
Call Trace:
<TASK>
dump_stack_lvl+0xcd/0x134
print_report.cold+0x2ba/0x719
kasan_report+0xb1/0x1e0
kasan_check_range+0x140/0x190
__mutex_unlock_slowpath+0xa6/0x5e0
l2cap_conn_del+0x404/0x7b0
l2cap_disconn_cfm+0x8c/0xc0
hci_conn_hash_flush+0x11f/0x260
hci_dev_close_sync+0x5f5/0x11f0
hci_dev_do_close+0x2d/0x70
hci_error_reset+0x9e/0x140
process_one_work+0x98a/0x1620
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0xbe/0xd0
call_rcu+0x99/0x740
netlink_release+0xe6a/0x1cf0
__sock_release+0xcd/0x280
sock_close+0x18/0x20
__fput+0x27c/0xa90
task_work_run+0xdd/0x1a0
exit_to_user_mode_prepare+0x23c/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0xbe/0xd0
call_rcu+0x99/0x740
netlink_release+0xe6a/0x1cf0
__sock_release+0xcd/0x280
sock_close+0x18/0x20
__fput+0x27c/0xa90
task_work_run+0xdd/0x1a0
exit_to_user_mode_prepare+0x23c/0x250
syscall_exit_to_user_mode+0x19/0x50
do_syscall_64+0x42/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 5c507b737a50 ("Bluetooth: L2CAP: Fix use-after-free caused by l2cap_chan_put") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An SKB can be queued by the first flow and immediately dequeued and
freed by the second flow, therefore the callers of l2cap_reassemble_sdu
can't use the SKB after that function returns. However, some places
continue accessing struct l2cap_ctrl that resides in the SKB's CB for a
short time after l2cap_reassemble_sdu returns, leading to a
use-after-free condition (the stack trace is below, line numbers for
kernel 5.19.8).
Fix it by keeping a local copy of struct l2cap_ctrl.
BUG: KASAN: use-after-free in l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
Read of size 1 at addr ffff88812025f2f0 by task kworker/u17:3/43169
Workqueue: hci0 hci_rx_work [bluetooth]
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
print_report.cold (mm/kasan/report.c:314 mm/kasan/report.c:429)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
kasan_report (mm/kasan/report.c:162 mm/kasan/report.c:493)
? l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx_state_recv (net/bluetooth/l2cap_core.c:6906) bluetooth
l2cap_rx (net/bluetooth/l2cap_core.c:7236 net/bluetooth/l2cap_core.c:7271) bluetooth
ret_from_fork (arch/x86/entry/entry_64.S:306)
</TASK>
Allocated by task 43169:
kasan_save_stack (mm/kasan/common.c:39)
__kasan_slab_alloc (mm/kasan/common.c:45 mm/kasan/common.c:436 mm/kasan/common.c:469)
kmem_cache_alloc_node (mm/slab.h:750 mm/slub.c:3243 mm/slub.c:3293)
__alloc_skb (net/core/skbuff.c:414)
l2cap_recv_frag (./include/net/bluetooth/bluetooth.h:425 net/bluetooth/l2cap_core.c:8329) bluetooth
l2cap_recv_acldata (net/bluetooth/l2cap_core.c:8442) bluetooth
hci_rx_work (net/bluetooth/hci_core.c:3642 net/bluetooth/hci_core.c:3832) bluetooth
process_one_work (kernel/workqueue.c:2289)
worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2437)
kthread (kernel/kthread.c:376)
ret_from_fork (arch/x86/entry/entry_64.S:306)
In the test_no_shared_qgroup() and test_multiple_refs() qgroup self tests,
if we fail to add the tree ref, remove the extent item or remove the
extent ref, we are returning from the test function without freeing the
"old_roots" ulist that was allocated by the previous calls to
btrfs_find_all_roots(). Fix that by calling ulist_free() before returning.
Fixes: ead7e1afe481 ("btrfs: qgroup: Switch self test to extent-oriented qgroup mechanism.") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During backref walking, at find_parent_nodes(), if we are dealing with a
data extent and we get an error while resolving the indirect backrefs, at
resolve_indirect_refs(), or in the while loop that iterates over the refs
in the direct refs rbtree, we end up leaking the inode lists attached to
the direct refs we have in the direct refs rbtree that were not yet added
to the refs ulist passed as argument to find_parent_nodes(). Since they
were not yet added to the refs ulist and prelim_release() does not free
the lists, on error the caller can only free the lists attached to the
refs that were added to the refs ulist, all the remaining refs get their
inode lists never freed, therefore leaking their memory.
Fix this by having prelim_release() always free any attached inode list
to each ref found in the rbtree, and have find_parent_nodes() set the
ref's inode list to NULL once it transfers ownership of the inode list
to a ref added to the refs ulist passed to find_parent_nodes().
Fixes: 72ed3b7fb0a0 ("btrfs: convert prelimary reference tracking to use rbtrees") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During backref walking, at resolve_indirect_refs(), if we get an error
we jump to the 'out' label and call ulist_free() on the 'parents' ulist,
which frees all the elements in the ulist - however that does not free
any inode lists that may be attached to elements, through the 'aux' field
of a ulist node, so we end up leaking lists if we have any attached to
the unodes.
Fix this by calling free_leaf_list() instead of ulist_free() when we exit
from resolve_indirect_refs(). The static function free_leaf_list() is
moved up for this to be possible and it's slightly simplified by removing
unnecessary code.
Fixes: 73d41712c45a ("Btrfs: add inodes before dropping the extent lock in find_all_leafs") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The class is set in mISDN_register_device(), but if device_add() returns
error, it will lead to delete a device without added, fix this by using
device_is_registered() to check if the device is registered.
Fixes: 8551bca14880 ("mISDN: Add support for Traverse Technologies NETJet PCI cards") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Afer commit 13e0419aca34 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
add put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
Set device class before put_device() to avoid null release() function
WARN message in device_release().
Fixes: 13e0419aca34 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387]
CPU: 0 PID: 4069 Comm: kworker/0:15 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Workqueue: rcu_gp srcu_invoke_callbacks
RIP: 0010:rose_send_frame+0x1dd/0x2f0 net/rose/rose_link.c:101
Call Trace:
<IRQ>
rose_transmit_clear_request+0x1d5/0x290 net/rose/rose_link.c:255
rose_rx_call_request+0x4c0/0x1bc0 net/rose/af_rose.c:1009
rose_loopback_timer+0x19e/0x590 net/rose/rose_loopback.c:111
call_timer_fn+0x1a0/0x6b0 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers.part.0+0x674/0xa80 kernel/time/timer.c:1790
__run_timers kernel/time/timer.c:1768 [inline]
run_timer_softirq+0xb3/0x1d0 kernel/time/timer.c:1803
__do_softirq+0x1d0/0x9c8 kernel/softirq.c:571
[...]
</IRQ>
It triggers NULL pointer dereference when 'neigh->dev->dev_addr' is
called in the rose_send_frame(). It's the first occurrence of the
`neigh` is in rose_loopback_timer() as `rose_loopback_neigh', and
the 'dev' in 'rose_loopback_neigh' is initialized sa nullptr.
During the initialization of ip_vs_app_net_init(), if file ip_vs_app
fails to be created, the initialization is successful by default.
Therefore, the ip_vs_app file doesn't be found during the remove in
ip_vs_app_net_cleanup(). It will cause WRNING.
The following is the stack information:
name 'ip_vs_app'
WARNING: CPU: 1 PID: 9 at fs/proc/generic.c:712 remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
Call Trace:
<TASK>
ops_exit_list+0x125/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 25bceb823b6e ("[NET]: Make /proc/net per network namespace") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During the initialization of ip_vs_conn_net_init(), if file ip_vs_conn
or ip_vs_conn_sync fails to be created, the initialization is successful
by default. Therefore, the ip_vs_conn or ip_vs_conn_sync file doesn't
be found during the remove.
The following is the stack information:
name 'ip_vs_conn_sync'
WARNING: CPU: 3 PID: 9 at fs/proc/generic.c:712
remove_proc_entry+0x389/0x460
Modules linked in:
Workqueue: netns cleanup_net
RIP: 0010:remove_proc_entry+0x389/0x460
Call Trace:
<TASK>
__ip_vs_cleanup_batch+0x7d/0x120
ops_exit_list+0x125/0x170
cleanup_net+0x4ea/0xb00
process_one_work+0x9bf/0x1710
worker_thread+0x665/0x1080
kthread+0x2e4/0x3a0
ret_from_fork+0x1f/0x30
</TASK>
The `char` type with no explicit sign is sometimes signed and sometimes
unsigned. This code will break on platforms such as arm, where char is
unsigned. So mark it here as explicitly signed, so that the
todrop_counter decrement and subsequent comparison is correct.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
No need to postpone this to the commit release path, since no packets
are walking over this object, this is accessed from control plane only.
This helped uncovered UAF triggered by races with the netlink notifier.
Recently, we got two syzkaller problems because of oversize packet
when napi frags enabled.
One of the problems is because the first seg size of the iov_iter
from user space is very big, it is 2147479538 which is bigger than
the threshold value for bail out early in __alloc_pages(). And
skb->pfmemalloc is true, __kmalloc_reserve() would use pfmemalloc
reserves without __GFP_NOWARN flag. Thus we got a warning as following:
The other problem is because odd IPv6 packets without NEXTHDR_NONE
extension header and have big packet length, it is 2127925 which is
bigger than ETH_MAX_MTU(65535). After ipv6_gso_pull_exthdrs() in
ipv6_gro_receive(), network_header offset and transport_header offset
are all bigger than U16_MAX. That would trigger skb->network_header
and skb->transport_header overflow error, because they are all '__u16'
type. Eventually, it would affect the value for __skb_push(skb, value),
and make it be a big value. After __skb_push() in ipv6_gro_receive(),
skb->data would less than skb->head, an out of bounds memory bug occurred.
That would trigger the problem as following:
To fix the problems, restrict the packet size less than
(ETH_MAX_MTU - NET_SKB_PAD - NET_IP_ALIGN) which has considered reserved
skb space in napi_alloc_skb() because transport_header is an offset from
skb->head. Add len check in tun_napi_alloc_frags() simply.
Fixes: 12d2dcce0caa ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20221029094101.1653855-1-william.xuanziyang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't use "skb" again after passing it to qdisc_enqueue(). This is
basically identical to commit f3b6138bca9f ("sch_sfb: Also store skb
len before calling child enqueue").
Fixes: 344a46181fff ("sch_red: update backlog as well") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log