raid10_sync_request() will add 'r10bio->remaining' for both rdev and
replacement rdev. However, if the read io fails, recovery_request_write()
returns without issuing the write io, in this case, end_sync_request()
is only called once and 'remaining' is leaked, cause an io hang.
Fix the problem by decreasing 'remaining' according to if 'bio' and
'repl_bio' is valid.
fcloop_fcp_op() could be called from flush request's ->end_io(flush_end_io) in
which the spinlock of fq->mq_flush_lock is grabbed with irq saved/disabled.
So fcloop_fcp_op() can't call spin_unlock_irq(&tfcp_req->reqlock) simply
which enables irq unconditionally.
Fixes the warning by switching to spin_lock_irqsave()/spin_unlock_irqrestore()
Fixes: d5ee36f356ce ("nvme-fcloop: fix inconsistent lock state warnings") Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the NVM Express Revision 1.4 spec, Figure 145 describes possible
values for an AER with event type "Error" (value 000b). For a
Persistent Internal Error (value 03h), the host should perform a
controller reset.
Add support for this error using code that already exists for
doing a controller reset. As part of this support, introduce
two utility functions for parsing the AER type and subtype.
This new support was tested in a lab environment where we can
generate the persistent internal error on demand, and observe
both the Linux side and NVMe controller side to see that the
controller reset has been done.
When huang uses sched_switch tracepoint, the tracepoint
does only one thing in the mounted ebpf program, which
deletes the fixed elements in sockhash ([0])
It seems that elements in sockhash are rarely actively
deleted by users or ebpf program. Therefore, we do not
pay much attention to their deletion. Compared with hash
maps, sockhash only provides spin_lock_bh protection.
This causes it to appear to have self-locking behavior
in the interrupt context.
When if_type equals zero and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns false, drbl_regs_memmap_p is not remapped. This passes a NULL
pointer to iounmap(), which can trigger a WARN() on certain arches.
When if_type equals six and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns true, drbl_regs_memmap_p may has been remapped and
ctrl_regs_memmap_p is not remapped. This is a resource leak and passes a
NULL pointer to iounmap().
To fix these issues, we need to add null checks before iounmap(), and
change some goto labels.
Fixes: 1af8f8753ae2 ("scsi: lpfc: Add push-to-adapter support to sli4") Signed-off-by: Shuchang Li <lishuchang@hust.edu.cn> Link: https://lore.kernel.org/r/20230404072133.1022-1-lishuchang@hust.edu.cn Reviewed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When jent initialisation fails for any reason other than ENOENT,
the entire drbg fails to initialise, even when we're not in FIPS
mode. This is wrong because we can still use the kernel RNG when
we're not in FIPS mode.
Change it so that it only fails when we are in FIPS mode.
Fixes: f5d76d425e91 ("crypto: drbg - Use callback API for random readiness") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that drbg_prepare_hrng() doesn't do anything but to instantiate a
jitterentropy crypto_rng instance, it looks a little odd to have the
related error handling at its only caller, drbg_instantiate().
Move the handling of jitterentropy allocation failures from
drbg_instantiate() close to the allocation itself in drbg_prepare_hrng().
There is no change in behaviour.
Signed-off-by: Nicolai Stange <nstange@suse.de> Reviewed-by: Stephan Müller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 686cd976b6dd ("crypto: drbg - Only fail when jent is unavailable in FIPS mode") Signed-off-by: Sasha Levin <sashal@kernel.org>
When dumping the control flow graphs for programs using the 16-byte long
load instruction, we need to skip the second part of this instruction
when looking for the next instruction to process. Otherwise, we end up
printing "BUG_ld_00" from the kernel disassembler in the CFG.
If there is a failure during copy_from_user or user-provided data buffer is
invalid, rtl_debugfs_set_write_reg should return negative error code instead
of a positive value count.
Fix this bug by returning correct error code. Moreover, the check of buffer
against null is removed since it will be handled by copy_from_user.
Fixes: cad581290f6d ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Wei Chen <harperchen1110@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230326054217.93492-1-harperchen1110@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is a failure during copy_from_user or user-provided data buffer
is invalid, rtl_debugfs_set_write_rfreg should return negative error code
instead of a positive value count.
Fix this bug by returning correct error code. Moreover, the check of buffer
against null is removed since it will be handled by copy_from_user.
Fixes: cad581290f6d ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Wei Chen <harperchen1110@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230326053138.91338-1-harperchen1110@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The macro name RT_TRACE makes it seem that it is used for tracing, when
is actually used for debugging. Change the name to rtl_dbg. Any Sparse
errors exposed by this change were also fixed.
Fix a bug added in commit 2a814ed51d43 ("scsi: target: iscsi: Fix cmd abort
fabric stop race").
If CMD_T_TAS is set on the se_cmd we must call iscsit_free_cmd() to do the
last put on the cmd and free it, because the connection is down and we will
not up sending the response and doing the put from the normal I/O
path.
Add a check for CMD_T_TAS in iscsit_release_commands_from_conn() so we now
detect this case and run iscsit_free_cmd().
Fixes: 2a814ed51d43 ("scsi: target: iscsi: Fix cmd abort fabric stop race") Signed-off-by: Mike Christie <michael.christie@oracle.com> Link: https://lore.kernel.org/r/20230319015620.96006-9-michael.christie@oracle.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
po->auxdata can be read while another thread
is changing its value, potentially raising KCSAN splat.
Convert it to PACKET_SOCK_AUXDATA flag.
Fixes: 874f90609601 ("[PACKET]: Add optional checksum computation for recvmsg") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot/KCAN reported that po->origdev can be read
while another thread is changing its value.
We can avoid this splat by converting this field
to an actual bit.
Following patches will convert remaining 1bit fields.
Fixes: 3dc15cc8ffbb ("[AF_PACKET]: Add option to return orig_dev to userspace.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
po->xmit can be set from setsockopt(PACKET_QDISC_BYPASS),
while read locklessly.
Use READ_ONCE()/WRITE_ONCE() to avoid potential load/store
tearing issues.
Fixes: da6f47518774 ("packet: introduce PACKET_QDISC_BYPASS socket option") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting timestamp filter was explicitly disabled on vlan devices in
containers because it might affect other processes on the host. But it's
absolutely legit in case when real device is in the same namespace.
Fixes: 6300f05aea50 ("vlan: disable SIOCSHWTSTAMP in container") Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, kernel would set MSG_CTRUNC flag if msg_control buffer
wasn't provided and SO_PASSCRED was set or if there was pending SCM_RIGHTS.
For some reason we have no corresponding check for SO_PASSSEC.
In the recvmsg(2) doc we have:
MSG_CTRUNC
indicates that some control data was discarded due to lack
of space in the buffer for ancillary data.
So, we need to set MSG_CTRUNC flag for all types of SCM.
This change can break applications those don't check MSG_CTRUNC flag.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Leon Romanovsky <leon@kernel.org> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
v2:
- commit message was rewritten according to Eric's suggestion Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
rtw_mac_power_switch() calls rtw_pwr_seq_parser() which can return
-EINVAL, -EBUSY or 0. Propagate the original error code instead of
unconditionally returning -EINVAL in case of an error.
Fixes: 6e4bd67d96b4 ("rtw88: new Realtek 802.11ac driver") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230226221004.138331-3-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
rtw_pwr_seq_parser() calls rtw_sub_pwr_seq_parser() which can either
return -EBUSY, -EINVAL or 0. Propagate the original error code instead
of unconditionally returning -EBUSY in case of an error.
Fixes: 6e4bd67d96b4 ("rtw88: new Realtek 802.11ac driver") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230226221004.138331-2-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
RFC8259 ("The JavaScript Object Notation (JSON) Data Interchange
Format") only specifies \", \\, \/, \b, \f, \n, \r, and \r as valid
two-character escape sequences. This does not include \', which is not
required in JSON because it exclusively uses double quotes as string
separators.
Solidus (/) may be escaped, but does not have to. Only reverse
solidus (\), double quotes ("), and the control characters have to be
escaped. Therefore, with this fix, bpftool correctly supports all valid
two-character escape sequences (but still does not support characters
that require multi-character escape sequences).
Witout this fix, attempting to load a JSON file generated by bpftool
using Python 3.10.6's default json.load() may fail with the error
"Invalid \escape" if the file contains the invalid escaped single
quote (\').
The warn is triggered on a known race condition, documented in the code above
the test, that is correctly handled. Using WARN() hinders automated testing.
Reducing severity.
Fixes: b36fa1192f6c ("ath6kl: Fix kernel panic on continuous driver load/unload") Reported-and-tested-by: syzbot+555908813b2ea35dae9a@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230126182431.867984-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
This loop checks that i < max at the start of loop but then it does
i++ which could put it past the end of the array. It's harmless to
check again and prevent a potential out of bounds.
Fixes: a88f6bb64b3c ("ath5k: Clean up eeprom parsing and add missing calibration data") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/Y+D9hPQrHfWBJhXz@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
hif_dev->remain_skb is allocated and used exclusively in
ath9k_hif_usb_rx_stream(). It is implied that an allocated remain_skb is
processed and subsequently freed (in error paths) only during the next
call of ath9k_hif_usb_rx_stream().
So, if the urbs are deallocated between those two calls due to the device
deinitialization or suspend, it is possible that ath9k_hif_usb_rx_stream()
is not called next time and the allocated remain_skb is leaked. Our local
Syzkaller instance was able to trigger that.
remain_skb makes sense when receiving two consecutive urbs which are
logically linked together, i.e. a specific data field from the first skb
indicates a cached skb to be allocated, memcpy'd with some data and
subsequently processed in the next call to ath9k_hif_usb_rx_stream(). Urbs
deallocation supposedly makes that link irrelevant so we need to free the
cached skb in those cases.
Fix the leak by introducing a function to explicitly free remain_skb (if
it is not NULL) when the rx urbs have been deallocated. remain_skb is NULL
when it has not been allocated at all (hif_dev struct is kzalloced) or
when it has been processed in next call to ath9k_hif_usb_rx_stream().
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: ee12d32d37b7 ("ath9k_htc: Support for AR9271 chipset.") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230216192301.171225-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
With HIGHRES enabled tick_sched_timer() is programmed every jiffy to
expire the timer_list timers. This timer is programmed accurate in
respect to CLOCK_MONOTONIC so that 0 seconds and nanoseconds is the
first tick and the next one is 1000/CONFIG_HZ ms later. For HZ=250 it is
every 4 ms and so based on the current time the next tick can be
computed.
This accuracy broke since the commit mentioned below because the jiffy
based clocksource is initialized with higher accuracy in
read_persistent_wall_and_boot_offset(). This higher accuracy is
inherited during the setup in tick_setup_device(). The timer still fires
every 4ms with HZ=250 but timer is no longer aligned with
CLOCK_MONOTONIC with 0 as it origin but has an offset in the us/ns part
of the timestamp. The offset differs with every boot and makes it
impossible for user land to align with the tick.
Align the tick period with CLOCK_MONOTONIC ensuring that it is always a
multiple of 1000/CONFIG_HZ ms.
The variable tick_period is initialized to NSEC_PER_TICK / HZ during boot
and never updated again.
If NSEC_PER_TICK is not an integer multiple of HZ this computation is less
accurate than TICK_NSEC which has proper rounding in place.
Aside of the inaccuracy there is no reason for having this variable at
all. It's just a pointless indirection and all usage sites can just use the
TICK_NSEC constant.
If jiffies are up to date already (caller lost the race against another
CPU) there is no point to change the sequence count. Doing that just forces
other CPUs into the seqcount retry loop in tick_nohz_next_event() for
nothing.
seqlock consists of a sequence counter and a spinlock_t which is used to
serialize the writers. spinlock_t is substituted by a "sleeping" spinlock
on PREEMPT_RT enabled kernels which breaks the usage in the timekeeping
code as the writers are executed in hard interrupt and therefore
non-preemptible context even on PREEMPT_RT.
The spinlock in seqlock cannot be unconditionally replaced by a
raw_spinlock_t as many seqlock users have nesting spinlock sections or
other code which is not suitable to run in truly atomic context on RT.
Instead of providing a raw_seqlock API for a single use case, open code the
seqlock for the jiffies use case and implement it with a raw_spinlock_t and
a sequence counter.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20200321113242.120587764@linutronix.de
Stable-dep-of: e9523a0d8189 ("tick/common: Align tick period with the HZ tick.") Signed-off-by: Sasha Levin <sashal@kernel.org>
Statically initialized objects are usually not initialized via the init()
function of the subsystem. They are special cased and the subsystem
provides a function to validate whether an object which is not yet tracked
by debugobjects is statically initialized. This means the object is started
to be tracked on first use, e.g. activation.
This works perfectly fine, unless there are two concurrent operations on
that object. Schspa decoded the problem:
subsys function modifies content of addr,
so static object detection does
not longer work.
unlock_subsytem_object(addr);
if (is_static_object(addr)) <- Fails
debugobject emits a warning and invokes the fixup function which
reinitializes the already active object in the worst case.
This race exists forever, but was never observed until mod_timer() got a
debug_object_assert_init() added which is outside of the timer base lock
held section right at the beginning of the function to cover the lockless
early exit points too.
Rework the code so that the lookup, the static object check and the
tracking object association happens atomically under the hash bucket
lock. This prevents the issue completely as all callers are serialized on
the hash bucket lock and therefore cannot observe inconsistent state.
Currently only the first attempt to single-step has any effect. After
that all further stepping remains "stuck" at the same program counter
value.
Refer to the ARM Architecture Reference Manual (ARM DDI 0487E.a) D2.12,
PSTATE.SS=1 should be set at each step before transferring the PE to the
'Active-not-pending' state. The problem here is PSTATE.SS=1 is not set
since the second single-step.
After the first single-step, the PE transferes to the 'Inactive' state,
with PSTATE.SS=0 and MDSCR.SS=1, thus PSTATE.SS won't be set to 1 due to
kernel_active_single_step()=true. Then the PE transferes to the
'Active-pending' state when ERET and returns to the debugger by step
exception.
Before this patch:
==================
Entering kdb (current=0xffff3376039f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb>
[0]kdb>
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffa45c13d09290 (write_sysrq_trigger)
is enabled addr at ffffa45c13d09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to Breakpoint @ 0xffffad651a309290
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb>
After this patch:
=================
Entering kdb (current=0xffff6851c39f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffc02d2dd09290 (write_sysrq_trigger)
is enabled addr at ffffc02d2dd09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to Breakpoint @ 0xffffc02d2dd09290
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09294
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09298
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd0929c
[1]kdb>
Fixes: 48911cff8d69 ("arm64: KGDB: Add step debugging support") Co-developed-by: Wei Li <liwei391@huawei.com> Signed-off-by: Wei Li <liwei391@huawei.com> Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Tested-by: Douglas Anderson <dianders@chromium.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Tested-by: Daniel Thompson <daniel.thompson@linaro.org> Link: https://lore.kernel.org/r/20230202073148.657746-3-sumit.garg@linaro.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch_dynirq_lower_bound() is invoked by the core interrupt code to
retrieve the lowest possible Linux interrupt number for dynamically
allocated interrupts like MSI.
The x86 implementation uses this to exclude the IO/APIC GSI space.
This works correctly as long as there is an IO/APIC registered, but
returns 0 if not. This has been observed in VMs where the BIOS does
not advertise an IO/APIC.
0 is an invalid interrupt number except for the legacy timer interrupt
on x86. The return value is unchecked in the core code, so it ends up
to allocate interrupt number 0 which is subsequently considered to be
invalid by the caller, e.g. the MSI allocation code.
The function has already a check for 0 in the case that an IO/APIC is
registered, as ioapic_dynirq_base is 0 in case of device tree setups.
Consolidate this and zero check for both ioapic_dynirq_base and gsi_top,
which is used in the case that no IO/APIC is registered.
Smatch reports:
drivers/regulator/stm32-pwr.c:166 stm32_pwr_regulator_probe() warn:
'base' from of_iomap() not released on lines: 151,166.
In stm32_pwr_regulator_probe(), base is not released
when devm_kzalloc() fails to allocate memory or
devm_regulator_register() fails to register a new regulator device,
which may cause a leak.
To fix this issue, replace of_iomap() with
devm_platform_ioremap_resource(). devm_platform_ioremap_resource()
is a specialized function for platform devices.
It allows 'base' to be automatically released whether the probe
function succeeds or fails.
Besides, use IS_ERR(base) instead of !base
as the return value of devm_platform_ioremap_resource()
can either be a pointer to the remapped memory or
an ERR_PTR() encoded error code if the operation fails.
The driver was intended from the start to be a wake-up source for the
system, however due to the absence of a suitable call to
device_set_wakeup_capable(), the device_may_wakeup() call used to decide
whether to enable the GPIO interrupt as a wake-up source would never
happen. Lookup the DT standard "wakeup-source" property and call
device_init_wakeup() to ensure the device is flagged as being wakeup
capable.
Reported-by: Matthew Lear <matthew.lear@broadcom.com> Fixes: 885ab7621d54 ("[media] rc: Add support for GPIO based IR Receiver driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
rcar_fcp_get() take reference, which should be balanced with
rcar_fcp_put(). Add missing rcar_fcp_put() in fdp1_remove and
the error paths of fdp1_probe() to fix this.
Fixes: 01ce9bfb8b6a ("[media] v4l: Add Renesas R-Car FDP1 Driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[hverkuil: resolve merge conflict, remove() is now void] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function fdp1_probe(), when get irq failed, the
function platform_get_irq() log an error message, so
remove redundant message here. And the variable type
of "ret" is int, the "fdp1->irq" is unsigned int, when
irq failed, this place maybe wrong, thus fix it.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stable-dep-of: c766c90faf93 ("media: rcar_fdp1: Fix refcount leak in probe and remove function") Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_get_sync() internally increments the
dev->power.usage_count without decrementing it, even on errors.
Replace it by the new pm_runtime_resume_and_get(), introduced by:
commit c4a28fe77ffc ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
in order to properly decrement the usage counter, avoiding
a potential PM usage counter leak.
Also, right now, the driver is ignoring any troubles when
trying to do PM resume. So, add the proper error handling
for the code.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stable-dep-of: c766c90faf93 ("media: rcar_fdp1: Fix refcount leak in probe and remove function") Signed-off-by: Sasha Levin <sashal@kernel.org>
In saa7134_initdev, it will call saa7134_hwinit1. There are three
function invoking here: saa7134_video_init1, saa7134_ts_init1
and saa7134_vbi_init1.
All of them will init a timer with same function. Take
saa7134_video_init1 as an example. It'll bound &dev->video_q.timeout
with saa7134_buffer_timeout.
In buffer_activate, the timer funtcion is started.
If we remove the module or device which will call saa7134_finidev
to make cleanup, there may be a unfinished work. The
possible sequence is as follows, which will cause a
typical UAF bug.
Fix it by canceling the timer works accordingly before cleanup in
saa7134_finidev.
In dm1105_probe, it called dm1105_ir_init and bound
&dm1105->ir.work with dm1105_emit_key.
When it handles IRQ request with dm1105_irq,
it may call schedule_work to start the work.
When we call dm1105_remove to remove the driver, there
may be a sequence as follows:
Fix it by finishing the work before cleanup in dm1105_remove
Fixes: fc4b26c7cd02 ("V4L/DVB: dm1105: use dm1105_dev & dev instead of dm1105dvb") Signed-off-by: Zheng Wang <zyytlz.wz@163.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The detection of atomic update failure in reserve_eilvt_offset() is
not correct. The value returned by atomic_cmpxchg() should be compared
to the old value from the location to be updated.
If these two are the same, then atomic update succeeded and
"eilvt_offsets[offset]" location is updated to "new" in an atomic way.
Otherwise, the atomic update failed and it should be retried with the
value from "eilvt_offsets[offset]" - exactly what atomic_try_cmpxchg()
does in a correct and more optimal way.
Fixes: 2c981c0c5a171 ("apic, x86: Check if EILVT APIC registers are available (AMD only)") Signed-off-by: Uros Bizjak <ubizjak@gmail.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/20230227160917.107820-1-ubizjak@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
An automated bot told me that there was a potential lockdep problem
with regulators. This was on the chromeos-5.15 kernel, but I see
nothing that would be different downstream compared to upstream. The
bot said:
============================================
WARNING: possible recursive locking detected 5.15.104-lockdep-17461-gc1e499ed6604 #1 Not tainted
--------------------------------------------
kworker/u16:4/115 is trying to acquire lock: ffffff8083110170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: create_regulator+0x398/0x7ec
but task is already holding lock: ffffff808378e170 (regulator_ww_class_mutex){+.+.}-{3:3}, at: ww_mutex_trylock+0x3c/0x7b8
other info that might help us debug this:
Possible unsafe locking scenario:
The problem was first reported soon after we made many of the
regulators probe asynchronously, though nothing I've seen implies that
the problems couldn't have also happened even without that.
I haven't personally been able to reproduce the lockdep issue, but the
issue does look somewhat legitimate. Specifically, it looks like in
regulator_resolve_supply() we are holding a "rdev" lock while calling
set_supply() -> create_regulator() which grabs the lock of a
_different_ "rdev" (the one for our supply). This is not necessarily
safe from a lockdep perspective since there is no documented ordering
between these two locks.
In reality, we should always be locking a regulator before the
supplying regulator, so I don't expect there to be any real deadlocks
in practice. However, the regulator framework in general doesn't
express this to lockdep.
Let's fix the issue by simply grabbing the two locks involved in the
same way we grab multiple locks elsewhere in the regulator framework:
using the "wound/wait" mechanisms.
When a codepath locks a rdev using ww_mutex_lock_slow() directly then
that codepath is responsible for incrementing the "ref_cnt" and also
setting the "mutex_owner" to "current".
The regulator core consistently got that right for "ref_cnt" but
didn't always get it right for "mutex_owner". Let's fix this.
It's unlikely that this truly matters because the "mutex_owner" is
only needed if we're going to do subsequent locking of the same
rdev. However, even though it's not truly needed it seems less
surprising if we consistently set "mutex_owner" properly.
If spec_reg is equal to 'SDHCI_PRESENT_STATE', esdhc_readl_fixup()
fixes up register value and returns it immediately. As a result, the
further block
(spec_reg == SDHCI_PRESENT_STATE)
&&(esdhc->quirk_ignore_data_inhibit == true),
is never executed.
The patch merges the second block into the first one.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ccbc768256db ("mmc: sdhci-of-esdhc: add quirk to ignore command inhibit for data") Signed-off-by: Georgii Kruglov <georgy.kruglov@yandex.ru> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20230321203715.3975-1-georgy.kruglov@yandex.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The runtime PM status can only be updated while runtime PM is disabled.
Drop the bogus pm_runtime_set_active() call that was made after enabling
runtime PM and which (incidentally but correctly) left the runtime PM
status set to 'suspended'.
Fixes: e7c1a247ee33 ("drm/msm/adreno: Load the firmware before bringing up the hardware") Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/524972/ Link: https://lore.kernel.org/r/20230303164807.13124-4-johan+linaro@kernel.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid preventing the display from coming up before the rootfs is
mounted, without resorting to packing fw in the initrd, the GPU has
this limbo state where the device is probed, but we aren't ready to
start sending commands to it. This is particularly problematic for
a6xx, since the GMU (which requires fw to be loaded) is the one that
is controlling the power/clk/icc votes.
So defer enabling runpm until we are ready to call gpu->hw_init(),
as that is a point where we know we have all the needed fw and are
ready to start sending commands to the coproc's.
adreno_gpu_init calls pm_runtime_enable, so adreno_gpu_cleanup needs to
call pm_runtime_disable.
Signed-off-by: Jonathan Marek <jonathan@marek.ca> Signed-off-by: Rob Clark <robdclark@chromium.org>
Stable-dep-of: db7662d076c9 ("drm/msm/adreno: drop bogus pm_runtime_set_active()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The buf[4] value comes from the user via ts_play(). It is a value in
the u8 range. The final length we pass to av7110_ipack_instant_repack()
is "len - (buf[4] + 1) - 4" so add a check to ensure that the length is
not negative. It's not clear that passing a negative len value does
anything bad necessarily, but it's not best practice.
With the new bounds checking the "if (!len)" condition is no longer
possible or required so remove that.
MEDIA_BUS_FMT_METADATA_FIXED should be used when
the same driver handles both sides of the link and
the bus format is a fixed metadata format that is
not configurable from userspace.
The width and height will be set to 0 for this format.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Acked-by: Helen Koike <helen.koike@collabora.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stable-dep-of: eed9496a0501 ("media: av7110: prevent underflow in write_ts_to_decoder()") Signed-off-by: Sasha Levin <sashal@kernel.org>
For 64KiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x10000. Hence, fix the bogus PCI addresses
(0x0fe00000, 0x31e00000, 0x35e00000) specified in the ranges property for
I/O region.
While at it, let's use the missing 0x prefix for the addresses.
The current value for pci IO is problematic for ath10k wifi card
commonly connected to ipq8064 SoC.
The current value is probably a typo and is actually uncommon to find
1MB IO space even on a x86 arch. Also with recent changes to the pci
driver, pci1 and pci2 now fails to function as any connected device
fails any reg read/write. Reduce this to 64K as it should be more than
enough and 3 * 64K of total IO space doesn't exceed the IO_SPACE_LIMIT
hardcoded for the ARM arch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Tested-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220707010943.20857-7-ansuelsmth@gmail.com
Stable-dep-of: 0b16b34e4916 ("ARM: dts: qcom: ipq8064: Fix the PCI I/O port range") Signed-off-by: Sasha Levin <sashal@kernel.org>
For 1MiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x100000. Hence, fix the bogus PCI address
(0x40200000) specified in the ranges property for I/O region.
While at it, let's use the missing 0x prefix for the addresses.
The current DRAM row address mapping arrays skx_{open,close}_row[]
only support ranks with sizes up to 16G. Decoding a rank address
to a DRAM row address for a 32G rank by using either one of the
above arrays by the skx_edac driver, will result in an overflow on
the array.
For a 32G rank, the most significant DRAM row address bit (the
bit17) is mapped from the bit34 of the rank address. Add this new
mapping item to both arrays to fix the overflow issue.
According to the RZ/G Series, 2nd Generation Hardware User’s Manual
Rev. 1.11, the System CPU cores on RZ/G2E do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
According to the R-Car Series, 3rd Generation Hardware User’s Manual
Rev. 2.30, the System CPU cores on R-Car E3 do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Currently we schedule a call to output_poll_execute from
drm_kms_helper_poll_enable for 10s in future. Later we try to replace
that in drm_helper_probe_single_connector_modes with a 0s schedule with
delayed_event set.
But as there is already a job in the queue this fails, and the immediate
job we wanted with delayed_event set doesn't occur until 10s later.
And that call acts as if connector state has changed, reprobing modes.
This has a side effect of waking up a display that has been blanked.
Make sure we cancel the old job before submitting the immediate one.
Fixes: 3cba33d620d3 ("drm/probe-helper: don't lose hotplug event") Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[Maxime: Switched to mod_delayed_work] Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20230127154052.452524-1-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
Given on-disk i_xattr_icount is 16 bits and xattr_isize is calculated
from i_xattr_icount multiplying 4, xattr_isize has a theoretical maximum
of 256K (64K * 4).
Thus declare xattr_isize as unsigned int to avoid the potential overflow.
Syzbot generated a crafted image [1] with a non-compact HEAD index of
clusterofs 33024 while valid numbers should be 0 ~ lclustersize-1,
which causes the following unexpected behavior as below:
BUG: unable to handle page fault for address: fffff52101a3fff9
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 23ffed067 P4D 23ffed067 PUD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 4398 Comm: kworker/u5:1 Not tainted 6.3.0-rc6-syzkaller-g09a9639e56c0 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
Workqueue: erofs_worker z_erofs_decompressqueue_work
RIP: 0010:z_erofs_decompress_queue+0xb7e/0x2b40
...
Call Trace:
<TASK>
z_erofs_decompressqueue_work+0x99/0xe0
process_one_work+0x8f6/0x1170
worker_thread+0xa63/0x1210
kthread+0x270/0x300
ret_from_fork+0x1f/0x30
Note that normal images or images using compact indexes are not
impacted. Let's fix this now.
If in tpm_tis_probe_irq_single() an error occurs after the original
interrupt vector has been read, restore the interrupts before the error is
returned.
Since the caller does not check the error value, return -1 in any case that
the TPM_CHIP_FLAG_IRQ flag is not set. Since the return value of function
tpm_tis_gen_interrupt() is not longer used, make it a void function.
Fixes: 6b3a3078b133 ("tpm_tis: Introduce intermediate layer for TPM access") Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Makefile rule responsible for building flask.h and
av_permissions.h only lists flask.h as a target which means that
av_permissions.h is only generated when flask.h needs to be
generated. This patch fixes this by adding av_permissions.h as a
target to the rule.
Fixes: 529f46898b09 ("selinux: generate flask headers during kernel build") Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make the flask.h target depend on the genheaders binary instead of
classmap.h to ensure that it is rebuilt if any of the dependencies of
genheaders are changed.
Notably this fixes flask.h not being rebuilt when
initial_sid_to_string.h is modified.
Fixes: 529f46898b09 ("selinux: generate flask headers during kernel build") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When opening a ubifs tmpfile on an encrypted directory, function
fscrypt_setup_filename allocates memory for the name that is to be
stored in the directory entry, but after the name has been copied to the
directory entry inode, the memory is not freed.
When running kmemleak on it we see that it is registered as a leak. The
report below is triggered by a simple program 'tmpfile' just opening a
tmpfile:
The commit f6df377e17af ("UBI: simplify LEB write and atomic LEB change code")
adds helper function, try_write_vid_and_data(), to simplify the code, but this
helper function has bug, it will return 0 (success) when ubi_io_write_vid_hdr()
or the ubi_io_write_data() return error number (-EIO, etc), because the return
value of ubi_wl_put_peb() will overwrite the original return value.
This issue will cause unexpected data loss issue, because the caller of this
function and UBIFS willn't know the data is lost.
Fixes: f6df377e17af ("UBI: simplify LEB write and atomic LEB change code") Cc: stable@vger.kernel.org Signed-off-by: Wang YanQing <udknight@gmail.com> Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following process will cause a memleak for copied up znode:
dirty_cow_znode
zn = copy_znode(c, znode);
err = insert_old_idx(c, zbr->lnum, zbr->offs);
if (unlikely(err))
return ERR_PTR(err); // No one refers to zn.
Fetch a reproducer in [Link].
Function copy_znode() is split into 2 parts: resource allocation
and znode replacement, insert_old_idx() is split in similar way,
so resource cleanup could be done in error handling path without
corrupting metadata(mem & disk).
It's okay that old index inserting is put behind of add_idx_dirt(),
old index is used in layout_leb_in_gaps(), so the two processes do
not depend on each other.
This reverts commit 122deabfe1428 (ubifs: dirty_cow_znode: Fix memleak
in error handling path).
After commit 122deabfe1428 applied, if insert_old_idx() failed, old
index neither exists in TNC nor in old-index tree. Which means that
old index node could be overwritten in layout_leb_in_gaps(), then
ubifs image will be corrupted in power-cut.
Using standard mode, rare false ACK responses were appearing with
i2cdetect tool. This was happening due to NACK interrupt triggering
ISR thread before register access interrupt was ready. Removing the
NACK interrupt's ability to trigger ISR thread lets register access
ready interrupt do this instead.
Extend VMX's nested intercept logic for emulated instructions to handle
"pause" interception, in quotes because KVM's emulator doesn't filter out
NOPs when checking for nested intercepts. Failure to allow emulation of
NOPs results in KVM injecting a #UD into L2 on any NOP that collides with
the emulator's definition of PAUSE, i.e. on all single-byte NOPs.
For PAUSE itself, honor L1's PAUSE-exiting control, but ignore PLE to
avoid unnecessarily injecting a #UD into L2. Per the SDM, the first
execution of PAUSE after VM-Entry is treated as the beginning of a new
loop, i.e. will never trigger a PLE VM-Exit, and so L1 can't expect any
given execution of PAUSE to deterministically exit.
... the processor considers this execution to be the first execution of
PAUSE in a loop. (It also does so for the first execution of PAUSE at
CPL 0 after VM entry.)
All that said, the PLE side of things is currently a moot point, as KVM
doesn't expose PLE to L1.
Note, vmx_check_intercept() is still wildly broken when L1 wants to
intercept an instruction, as KVM injects a #UD instead of synthesizing a
nested VM-Exit. That issue extends far beyond NOP/PAUSE and needs far
more effort to fix, i.e. is a problem for the future.
Fixes: 742795a47032 ("KVM: nVMX: Don't emulate instructions in guest mode") Cc: Mathias Krause <minipli@grsecurity.net> Cc: stable@vger.kernel.org Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Link: https://lore.kernel.org/r/20230405002359.418138-1-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reiserfs sets a security xattr at inode creation time in two stages: first,
it calls reiserfs_security_init() to obtain the xattr from active LSMs;
then, it calls reiserfs_security_write() to actually write that xattr.
Unfortunately, it seems there is a wrong expectation that LSMs provide the
full xattr name in the form 'security.<suffix>'. However, LSMs always
provided just the suffix, causing reiserfs to not write the xattr at all
(if the suffix is shorter than the prefix), or to write an xattr with the
wrong name.
Add a temporary buffer in reiserfs_security_write(), and write to it the
full xattr name, before passing it to reiserfs_xattr_set_handle().
Also replace the name length check with a check that the full xattr name is
not larger than XATTR_NAME_MAX.
Cc: stable@vger.kernel.org # v2.6.x Fixes: c898ba4ee8d8 ("reiserfs: add atomic addition of selinux attributes during inode creation") Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If something was written to the buffer just before destruction,
it may be possible (maybe not in a real system, but it did
happen in ARCH=um with time-travel) to destroy the ringbuffer
before the IRQ work ran, leading this KASAN report (or a crash
without KASAN):
BUG: KASAN: slab-use-after-free in irq_work_run_list+0x11a/0x13a
Read of size 8 at addr 000000006d640a48 by task swapper/0
The buggy address belongs to the object at 000000006d640800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 584 bytes inside of
freed 1024-byte region [000000006d640800, 000000006d640c00)
Add the appropriate irq_work_sync() so the work finishes before
the buffers are destroyed.
Prior to the commit in the Fixes tag below, there was only a
single global IRQ work, so this issue didn't exist.
This fix is basically the same as db6c7f7177a1 ("pwm: meson: Fix the
G12A AO clock parents order"). Vendor driver referenced there has
xtal as first parent also for axg ao. In addition fix the name
of the aoclk81 clock. Apparently name aoclk81 as used by the vendor
driver was changed when mainlining the axg clock driver.
Under CONFIG_FORTIFY_SOURCE, memcpy() will check the size of destination
and source buffers. Defining kernel_headers_data as "char" would trip
this check. Since these addresses are treated as byte arrays, define
them as arrays (as done everywhere else).
This was seen with:
$ cat /sys/kernel/kheaders.tar.xz >> /dev/null
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1027!
...
RIP: 0010:fortify_panic+0xf/0x20
[...]
Call Trace:
<TASK>
ikheaders_read+0x45/0x50 [kheaders]
kernfs_fop_read_iter+0x1a4/0x2f0
...
Reported-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/bpf/20230302112130.6e402a98@kernel.org/ Acked-by: Joel Fernandes (Google) <joel@joelfernandes.org> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Jakub Kicinski <kuba@kernel.org> Fixes: eaae2b3dc54b ("Provide in-kernel headers to make extending kernel easier") Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20230302224946.never.243-kees@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipmi communication is not restored after a specific version of BMC is
upgraded on our server.
The ipmi driver does not respond after printing the following log:
ipmi_ssif: Invalid response getting flags: 1c 1
I found that after entering this branch, ssif_info->ssif_state always
holds SSIF_GETTING_FLAGS and never return to IDLE.
As a result, the driver cannot be loaded, because the driver status is
checked during the unload process and must be IDLE in shutdown_ssif():
while (ssif_info->ssif_state != SSIF_IDLE)
schedule_timeout(1);
The process trigger this problem is:
1. One msg timeout and next msg start send, and call
ssif_set_need_watch().
2. ssif_set_need_watch()->watch_timeout()->start_flag_fetch() change
ssif_state to SSIF_GETTING_FLAGS.
3. In msg_done_handler() ssif_state == SSIF_GETTING_FLAGS, if an error
message is received, the second branch does not modify the ssif_state.
4. All retry action need IS_SSIF_IDLE() == True. Include retry action in
watch_timeout(), msg_done_handler(). Sending msg does not work either.
SSIF_IDLE is also checked in start_next_msg().
5. The only thing that can be triggered in the SSIF driver is
watch_timeout(), after destory_user(), this timer will stop too.
So, if enter this branch, the ssif_state will remain SSIF_GETTING_FLAGS
and can't send msg, no timer started, can't unload.
We did a comparative test before and after adding this patch, and the
result is effective.
Wire up the debugfs regset device pointer so that the controller is
resumed before accessing registers to avoid crashing or locking up if it
happens to be runtime suspended.
Hardware registers of devices under control of power management cannot
be accessed at all times. If such a device is suspended, register
accesses may lead to undefined behavior, like reading bogus values, or
causing exceptions or system lock-ups.
Extend struct debugfs_regset32 with an optional field to let device
drivers specify the device the registers in the set belong to. This
allows debugfs_show_regset32() to make sure the device is resumed while
its registers are being read.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Acer Iconia One 7 B1-750 tablet mostly works fine with the defaults
for an Bay Trail CR tablet. Except for the internal mic, instead of
an analog mic on IN3 a digital mic on DMIC1 is uses.
Add a quirk with these settings for this tablet.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230322145332.131525-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add UNISOC vendor ID and TOZED LT70-C modem which is based from UNISOC
SL8563. The modem supports the NCM mode. Interface 0 is used for running
the AT commands. Interface 12 is the ADB interface.
Previously, capability was checked using capable(), which verified that the
caller of the ioctl system call had the required capability. In addition,
the result of the check would be stored in the HCI_SOCK_TRUSTED flag,
making it persistent for the socket.
However, malicious programs can abuse this approach by deliberately sharing
an HCI socket with a privileged task. The HCI socket will be marked as
trusted when the privileged task occasionally makes an ioctl call.
This problem can be solved by using sk_capable() to check capability, which
ensures that not only the current task but also the socket opener has the
specified capability, thus reducing the risk of privilege escalation
through the previously identified vulnerability.
Cc: stable@vger.kernel.org Fixes: 33d8d400fad8 ("Bluetooth: Send control open and close messages for HCI raw sockets") Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are supposed to fix this up if needed if they don't outright
reject it. Uncovered by 8f58637f1958 ("fbmem: Check virtual screen
sizes in fb_set_var()").
projects / kernel.git / log