Bit definitions for port-select got changed for TRANS_CLK_SEL &
TRANS_DDI_FUNC_CTL registers in TGL.
v2 (Lucas):
- Nuke TRANS_DDI_PORT_NONE since it's 0: we are already clearing
{TGL_,}TRANS_DDI_PORT_MASK (suggested by Ville)
- Also cover haswell_get_ddi_port_state() in intel_display.c that was
missing
- Define macros using the _SHIFT macros so we don't lose other users
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com> Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190713010940.17711-3-lucas.demarchi@intel.com
Lucas De Marchi [Sat, 13 Jul 2019 01:09:19 +0000 (18:09 -0700)]
drm/i915/tgl: skip setting PORT_CL_DW12_* on initialization
According to the spec when initializing the display in TGL we should not
set PORT_CL_DW12 for the Aux channel of the combo PHYs. We will re-use the
power well hooks from ICL so only set this register on gen < 12.
v2: Generalize check for gen 12 (suggested by José)
v3: Rebase after enum phy introduction
According to Firmware layout definition, RSA signature is located
after CSS header and uCode so actual RSA offset in the blob can be
easily calculated when needed (and we need it only once).
According to Firmware layout definition, CSS header is located
in front of the firmware blob, so header offset is always 0.
Similarly, size of the CSS header is constant and currently
used version is exactly 128.
While here, move type/status enums up and keep them together.
v2: use sizeof consistently (Daniele), update commit message
Chris Wilson [Thu, 25 Jul 2019 13:14:46 +0000 (14:14 +0100)]
drm/i915/gt: Add to timeline requires the timeline mutex
Modifying a remote context requires careful serialisation with requests
on that context, and that serialisation requires us to take their
timeline->mutex. Make it so.
Note that while struct_mutex rules, we can't create more than one
request in parallel, but that age is soon coming to an end.
v2: Though it doesn't affect the current users, contexts may share
timelines so check if we already hold the right mutex.
drm/i915/guc: init submission structures as part of guc_init
guc->stage_desc_pool is required as part of the init parameters and
there is no reason we have to init them after HuC. This fixes a NULL
ptr dereference due to guc->stage_desc_pool not being set (no fixes
tag since GuC submission can't be enabled yet).
Chris Wilson [Thu, 25 Jul 2019 22:38:43 +0000 (23:38 +0100)]
drm/i915: Capture vma contents outside of spinlock
Currently we use the engine->active.lock to ensure that the request is
not retired as we capture the data. However, we only need to ensure that
the vma are not removed prior to use acquiring their contents, and
since we have already relinquished our stop-machine protection, we
assume that the user will not be overwriting the contents before we are
able to record them.
In order to capture the vma outside of the spinlock, we acquire a
reference and mark the vma as active to prevent it from being unbound.
However, since it is tricky allocate an entry in the fence tree (doing
so would require taking a mutex) while inside the engine spinlock, we
use an atomic bit and special case the handling for i915_active_wait.
The core benefit is that we can use some non-atomic methods for mapping
the device pages, we can remove the slow compression phase out of atomic
context (i.e. stop antagonising the nmi-watchdog), and no we longer need
large reserves of atomic pages.
Michal Wajdeczko [Thu, 25 Jul 2019 14:13:06 +0000 (14:13 +0000)]
drm/i915: Fix GuC documentation links
We moved GuC related files to new location but we missed to update
.rst file with links.
References: commit 91a9d71b0122 ("drm/i915/uc: move GuC and HuC files under gt/uc/") Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190725141308.24660-1-michal.wajdeczko@intel.com
The way we load the firmwares is the same for both GuC and HuC, the only
difference is in the wopcm destination address and the dma flags, so we
easily can move the logic to a common function and pass in offset and
flags. The only other difference in the uplaod path are some the extra
steps that guc does before and after the xfer, but those don't require
the guc fw to be pinned in ggtt and can safely be performed before
calling the uc_upload function.
Note that this patch re-introduces the dma xfer wait for guc loading that
was removed with "drm/i915/guc: Propagate the fw xfer timeout". This is
not going to slow us down on a successful load (the dma has to complete
before fw init can start), but could slightly increase the timeout in case
of a fw init error.
v2: use _fw variants for uncore accesses (Chris), fix guc_fw status on
failed wait.
The gt is our new central structure for uc-related code, so we can use
that instead of jumping back to i915 via the fw object. Since we have it
in the upload function it is easy to pass it through the lower levels of
the xfer process instead of continuosly jumping via uc_fw->uc->gt, which
will also make things a bit cleaner for the next patch.
The binary is perma-pinned and the rsa is not going to change, so copy
it only once and not on every load.
v2: onion unwind (Chris)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Fernando Pacheco <fernando.pacheco@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1 Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190725001813.4740-7-daniele.ceraolospurio@intel.com
drm/i915/uc: Move xfer rsa logic to common function
The way we copy the RSA is the same for GuC and HuC, so we can move the
logic in a common function. this will also make any update needed for
local memory easier.
v2: return the number of copied bytes and check it (Chris)
We currently track fetch and load status separately, but the 2 are
actually sequential in the uc lifetime (fetch must complete before we
can attempt the load!). Unifying the 2 variables we can better follow
the sequential states and improve our trackng of the uC state.
Also, sprinkle some GEM_BUG_ON to make sure we transition correctly
between states.
v2: rename states, add the running state (Michal), drop some logs in
the fetch path (Michal, Chris)
v3: re-rename states, extend early status check to all helpers (Michal)
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190725001813.4740-5-daniele.ceraolospurio@intel.com
Instead of having 2 identical functions for GuC and HuC firmware
selection, we can unify the selection logic and just use different lists
based on FW type.
Note that the revid is not relevant for current blobs, but the upcoming
CML will be identified as CFL rev 5, so by considering the revid we're
ready for that.
v2: rework blob list defs (Michal), add order check (Chris), fuse GuC
and HuC lists into one.
v3: remove difference between no uC HW and no uC FW, simplify related
selection code, check the whole fw list (Michal)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Anusha Srivatsa <anusha.srivatsa@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v2 Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190725001813.4740-4-daniele.ceraolospurio@intel.com
There are 2 issues around handling of missing uC support:
- We treat lack of uC HW and lack of uC FW definition as 2 different
cases, but both of them mean that we don't support the uC on the
platform we're running on.
- We rely on the modparam to decide if we can take uC paths or not, but
we don't sanitize it if it is set incorrectly on platform with no uC
support.
To fix both of them, unify the 2 cases in a single one and sanitize the
modparam on invalid configuration (after printing an error message).
The log has been adapted as well, since the user doesn't care why we
don't support GuC/HuC (no HW or no FW), just that we do not. Developers
can easily find the answer based on the platform, so we can simplify the
log.
Correcting the modparam has been preferred over failing the load since
this is what we usually do for non-supported feature (e.g. the now gone
enable_ppgtt would fall back to the highest supported PPGTT mode if the
selected one was not available).
Note that this patch purposely doesn't change the behavior for platforms
that do have uC support, in which case we will still fail if enable_guc
is set and the firmware is not available on the system.
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190725001813.4740-3-daniele.ceraolospurio@intel.com
We have several HAS_* checks for GuC and HuC but we mostly use HAS_GUC
and HAS_HUC, with only 1 exception. Since our HW always has either
both uC or neither of them, just replace all the checks with a unified
HAS_UC.
v2: use HAS_GT_UC (Michal)
v3: fix comment (Michal)
All the GuC objects are perma-pinned, so their offset can't change at
runtime. We can therefore set (and log!) the parameters only once during
boot.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190724085849.18047-1-chris@chris-wilson.co.uk
Fix botched refactoring of the code that uncorrectly split a check on a
bool, treating it as a u32.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: d9f9df080029 ("drm/i915/uc: prefer intel_gt over i915 in GuC/HuC paths") Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190723153733.19401-1-daniele.ceraolospurio@intel.com
Chris Wilson [Tue, 23 Jul 2019 09:12:18 +0000 (10:12 +0100)]
drm/i915: Squelch nop wait-for-idle trace
If the system is already idle, omit the GEM_TRACE saying we are about to
wait for idle. It looks confusing in the logs to see a continual stream
of wait-for-idle, as one immediately assumes it is stuck in a loop.
Chris Wilson [Tue, 23 Jul 2019 09:58:00 +0000 (10:58 +0100)]
drm/i915/selftests: Let igt_vma_partial et al breathe
Give the scheduler a chance to breathe by calling cond_resched() as some
of the loops may take some time on slower machines, and so catch the
attention of the watchdogs.
The microcontrollers are part of GT so it makes logical sense to have
them sanitized at the same time. This also fixed an issue with our
status tracking where the FW load status is not reset around
hibernation.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190723091404.6449-2-chris@chris-wilson.co.uk
drm/i915: Add HDCP capability info to i915_display_info.
To identify the HDCP capability of the display connected to CI
systems, we need to add the hdcp capability probing in i915_display_info.
This will also help to populate the HDCP capability of the CI systems
to CI H/W logs maintained at https://intel-gfx-ci.01.org/hardware/.
It will facilitate to determine the kms_content_protection behavior on
a particular CI system.
v2: Reused the intel_hdcp_info() in i915_hdcp_sink_capability_show(). [Ram]
Shifted intel_hdcp_info() to the end of intel_dp_info. [Ram]
v3: used seq_puts() instead of seq_pritnf(). [Ram]
Chris Wilson [Mon, 22 Jul 2019 22:28:47 +0000 (23:28 +0100)]
drm/i915: Rely on spinlock protection for GPU error capture
Trust that we now have adequate protection over the low level structures
via the engine->active.lock to allow ourselves to capture the GPU error
state without the heavy hammer of stop_machine(). Sadly this does mean
that we have to forgo some of the lesser used information (not derived
from the active state) that is not controlled by the active locks. This
includes the list of buffers in the ppGTT and pinned globally in the
GGTT. Originally this was used to manually verify relocations, but
hasn't been required for sometime and modern mesa now has the habit of
ensuring that all interesting buffers within a batch are captured in their
entirety (that are the auxiliary state buffers, but not the textures).
A useful side-effect is that this allows us to restore error capturing
for Braswell and Broxton.
v2: Use pagevec for a typical arbitrary number of preallocated pages
Chris Wilson [Thu, 18 Jul 2019 07:00:06 +0000 (08:00 +0100)]
drm/i915/gt: Hook up intel_context_fini()
Prior to freeing the struct, call the fini function to cleanup the
common members. Currently this only calls the debug functions to mark
the structs as destroyed, but may be extended to real work in future.
Chris Wilson [Thu, 18 Jul 2019 07:00:10 +0000 (08:00 +0100)]
drm/i915: Remove obsolete engine cleanup
Remove the outer layer cleanup of engine stubs; as i915_drv itself no
longer tries to preallocate and so is not responsible for either the
allocation or free. By the time we call the cleanup function, we already
have cleaned up the engines.
v2: Lack of symmetry between mmio_probe and mmio_release for handling
the error cleanup. engine->destroy() is a compound function that is
called earlier in the normal release as it ties together other bits of
state.
Chris Wilson [Fri, 19 Jul 2019 13:07:37 +0000 (14:07 +0100)]
drm/i915/gtt: Fix rounding for 36b
The top-level page directory for 36b is a single entry, not multiple
like 32b. Fix up the rounding on the calculation of the size of the top
level so that we populate the 4th level correctly for 36b.
Reported-by: Jose Souza <jose.souza@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Fixes: 4c5ad7d98b06 ("drm/i915/gtt: Recursive cleanup for gen8") Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Cc: Jose Souza <jose.souza@intel.com> Tested-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190719130737.5835-1-chris@chris-wilson.co.uk
drm/i915/dsi: remove set but not used variable 'hfront_porch'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/i915/display/icl_dsi.c: In function 'gen11_dsi_set_transcoder_timings':
drivers/gpu/drm/i915/display/icl_dsi.c:768:6: warning:
variable 'hfront_porch' set but not used [-Wunused-but-set-variable]
Michal Wajdeczko [Fri, 19 Jul 2019 15:33:22 +0000 (15:33 +0000)]
drm/i915/gtt: Don't try to clear failed empty pd allocation
When __gen8_ppgtt_alloc fails without allocating anything
we should not try to call __gen8_ppgtt_clear as there is
nothing to clear and underlying code will complain with:
drm/i915/icl: Verify engine workarounds in GEN8_L3SQCREG4
Having fixed the incorect MCR programming in an earlier patch, we can now
stop ignoring read back of GEN8_L3SQCREG4 during engine workaround
verification.
drm/i915: Skip CS verification of L3 bank registers
Access to 0xb100 - 0xb3ff mmio range is controlled by the MCR selector
which only affects CPU MMIO. Therefore these registers cannot be realiably
read with MI_SRM from the command streamer so skip their verification.
1.
fls() usage was incorrect causing off by one in subslice mask lookup,
which in other words means subslice mask of all zeroes is always used
(subslice mask of a slice which is not present, or even out of bounds
array access), rendering the checks in wa_init_mcr either futile or
random.
2.
Condition in WARN_ON was not correct. It is doing a bitwise and operation
between a positive (present subslices) and negative mask (disabled L3
banks).
This means that with corrected fls() usage the assert would always
incorrectly fail.
We could fix this by inverting the fuse bits in the check, but instead do
one better and improve the code so it not only asserts, but finds the
first common index between the two masks and only warns if no such index
can be found.
v2:
* Simplify check for logic and redability.
* Improve commentary explaining what is really happening ie. what the
assert is really trying to check and why.
v3:
* Find first common index instead of just asserting.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Fixes: a11d4e471f7e ("drm/i915: Implement WaProgramMgsrForL3BankSpecificMmioReads") Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v1 Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: Stuart Summers <stuart.summers@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190717180624.20354-4-tvrtko.ursulin@linux.intel.com
fls returns bit positions starting from one for the lsb and the MCR
register expects zero based (sub)slice addressing.
Incorrent MCR programming can have the effect of directing MMIO reads of
registers in the 0xb100-0xb3ff range to invalid subslice returning zeroes
instead of actual content.
drm/i915: Remove set but not used variable 'src_y'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/i915/display/intel_sprite.c: In function 'g4x_sprite_check_scaling':
drivers/gpu/drm/i915/display/intel_sprite.c:1494:13: warning:
variable 'src_y' set but not used [-Wunused-but-set-variable]
Chris Wilson [Tue, 16 Jul 2019 12:49:30 +0000 (13:49 +0100)]
drm/i915/execlists: Cancel breadcrumb on preempting the virtual engine
As we unwind the requests for a preemption event, we return a virtual
request back to its original virtual engine (so that it is available for
execution on any of its siblings). In the process, this means that its
breadcrumb should no longer be associated with the original physical
engine, and so we are forced to decouple it. Previously, as the request
could not complete without our awareness, we would move it to the next
real engine without any danger. However, preempt-to-busy allowed for
requests to continue on the HW and complete in the background as we
unwound, which meant that we could end up retiring the request before
fixing up the breadcrumb link.
A single 32-bit PSR2 training pattern field follows the sixteen element
array of PSR table entries in the VBT spec. But, we incorrectly define
this PSR2 field for each of the PSR table entries. As a result, the PSR1
training pattern duration for any panel_type != 0 will be parsed
incorrectly. Secondly, PSR2 training pattern durations for VBTs with bdb
version >= 226 will also be wrong.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: stable@vger.kernel.org Cc: stable@vger.kernel.org #v5.2 Fixes: e9fd5f4172de ("drm/i915/vbt: Parse and use the new field with PSR2 TP2/3 wakeup time")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111088
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204183 Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Tested-by: François Guerraz <kubrick@fgv6.net> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190717223451.2595-1-dhinakaran.pandiyan@intel.com
Chris Wilson [Thu, 18 Jul 2019 14:54:05 +0000 (15:54 +0100)]
drm/i915: Use maximum write flush for pwrite_gtt
As recently disovered by forcing big-core (!llc) machines to use the GTT
paths, we need our full GTT write flush before manipulating the GTT PTE
or else the writes may be directed to the wrong page.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Matthew Auld <matthew.william.auld@gmail.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190718145407.21352-2-chris@chris-wilson.co.uk
Ville Syrjälä [Wed, 17 Jul 2019 11:45:36 +0000 (14:45 +0300)]
drm/i915: Make sure cdclk is high enough for DP audio on VLV/CHV
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
drm/i915/ehl: Use an id of 4 while accessing DPLL4's CR0 and CR1
Although, DPLL4 enable and disable is associated with MGPLL1_ENABLE
register, we can use ICL_DPLL_CFGCR0/CR1 macros to access this dpll's
CR0 and CR1 registers by passing an id of 4 to these macros.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190717021316.18610-1-vivek.kasireddy@intel.com
Chris Wilson [Tue, 16 Jul 2019 12:49:28 +0000 (13:49 +0100)]
drm/i915/gt: Push engine stopping into reset-prepare
Push the engine stop into the back reset_prepare (where it already was!)
This allows us to avoid dangerously setting the RING registers to 0 for
logical contexts. If we clear the register on a live context, those
invalid register values are recorded in the logical context state and
replayed (with hilarious results).
Chris Wilson [Tue, 16 Jul 2019 12:49:29 +0000 (13:49 +0100)]
drm/i915/execlists: Process interrupted context on reset
By stopping the rings, we may trigger an arbitration point resulting in
a premature context-switch (i.e. a completion event before the request
is actually complete). This clears the active context before the reset,
but we must remember to rewind the incomplete context for replay upon
resume.
Chris Wilson [Tue, 16 Jul 2019 21:34:43 +0000 (22:34 +0100)]
drm/i915/oa: Reconfigure contexts on the fly
Avoid a global idle barrier by reconfiguring each context by rewriting
them with MI_STORE_DWORD from the kernel context.
v2: We only need to determine the desired register values once, they are
the same for all contexts.
v3: Don't remove the kernel context from the list of known GEM contexts;
the world is not ready for that yet.
Chris Wilson [Mon, 15 Jul 2019 08:09:28 +0000 (09:09 +0100)]
drm/i915: Lock the engine while dumping the active request
We cannot let the request be retired and freed while we are trying to
dump it during error capture. It is not sufficient just to grab a
reference to the request, as during retirement we may free the ring
which we are also dumping. So take the engine lock to prevent retiring
and freeing of the request.
Reported-by: Alex Shumsky <alexthreed@gmail.com> Fixes: 6ef6f0f4b80e ("drm/i915: Dump the ringbuffer of the active request for debugging") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Alex Shumsky <alexthreed@gmail.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190715080946.15593-6-chris@chris-wilson.co.uk
Right now we are aware of two cases that needs another hotplug retry:
- Unpowered type-c dongles
- HDMI slow unplug
Both have a complete explanation in the code to schedule another run
of the hotplug handler.
It could have more checks to just trigger the retry in those two
specific cases but why would sink signal a long pulse if there is
no change? Also the drawback of running the hotplug handler again
is really low and that could fix another cases that we are not
aware.
Also retrying for old DP ports(non-DDI) to make it consistent and not
cause CI failures if those systems are connected to chamelium boards
that will be used to simulate the issues reported in here.
v2: Also retrying for old DP ports(non-DDI)(Imre)
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-2-jose.souza@intel.com
Imre Deak [Fri, 12 Jul 2019 00:53:42 +0000 (17:53 -0700)]
drm/i915: Add support for retrying hotplug
There is some scenarios that we are aware that sink probe can fail,
so lets add the infrastructure to let hotplug() hook to request
another probe after some time.
v2: Handle shared HPD pins (Imre)
v3: Rebased
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
v5: Making the working queue used explicit through all the callers to
hotplug_work (Ville)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-1-jose.souza@intel.com
Chris Wilson [Fri, 12 Jul 2019 08:25:49 +0000 (09:25 +0100)]
drm/i915/selftests: Ignore self-preemption suppression under gvt
GVT forces single port submission of individual requests. We do not
enjoy the context amalgamation that the test depends upon for setting up
the test (where port 0 has a large number of requests with a priority
change somewhere in the middle). Under single request submission of gvt
it is quite able for the preemption event to occur while another context
is active and so there be a real need to act upon that preemption.
Get rid of them to avoid more users being added while the guc code
transitions to use gt more than i915.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Acked-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-11-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915/guc: prefer intel_gt in guc interrupt functions
We can get rid of a few more guc_to_i915 and start compartmentalizing
interrupt management a bit more. We should be able to move more code in
the future once the gt_pm code is also moved across to gt.
drm/i915/uc: prefer intel_gt over i915 in GuC/HuC paths
With our HW interface logic moving from i915 to gt and with GuC and HuC
being part of the gt HW, it makes sense to use the intel_gt structure
instead of i915 as our reference object in GuC/HuC paths.
All the intel_uc_* can now be moved to work on the intel_uc structure
for better encapsulation of uc-related actions.
Note: I've introduced uc_to_gt instead of uc_to_i915 because the aim is
to move everything to be gt-focused in the medium term, so we would've
had to replace it soon anyway.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Acked-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-8-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
drm/i915/uc: move GuC/HuC inside intel_gt under a new intel_uc
Being part of the GT HW, it make sense to keep the guc/huc structures
inside the GT structure. To help with the encapsulation work done by the
following patches, both structures are placed inside a new intel_uc
container. Although this results in code with ugly nested dereferences
(i915->gt.uc.guc...), it saves us the extra work required in moving
the structures twice (i915 -> gt -> uc). The following patches will
reduce the number of places where we try to access the guc/huc
structures directly from i915 and reduce the ugliness.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-7-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Both microcontrollers are part of the GT HW and are closely related to
GT operations. To keep all the files cleanly together, they've been
placed in their own subdir inside the gt/ folder
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-6-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The 16-bit guc irq vector is unchanged across gens, the only thing that
moved is its position (from the upper 16 bits of the PM regs to its own
register). Instead of duplicating all defines and functions to handle
the 2 different positions, we can work on the vector and shift it as
appropriate. While at it, update the handler to work on intel_guc.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-5-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of always checking in the device config is GuC and HuC are
supported or not, we can save the state in the uc_fw structure and
avoid going through i915 every time from the low-level uc management
code. while at it FIRMWARE_NONE has been renamed to better indicate that
we haven't started the fetch/load yet, but we might have already selected
a blob.
The "misc" terminology doesn't clearly explain what we intend to cover
in this phase. The only thing we used ot do in there apart from FW fetch
was initializing the log workqueue, with the latter being required only in
the very rare case where we enable the log relay. As we no longer create
our own workqueue, piggybacking on the system_highpri_wq instead, we can
rename the function to clarify that they only fetch/release the blobs.
v2: only create log wq when needed (Michal), reword commit msg
accordingly
v3: after rebase the wq is gone, reword commit msg accordingly
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-2-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Sat, 13 Jul 2019 10:00:06 +0000 (11:00 +0100)]
drm/i915/guc: Use system workqueue for log capture
We only employ a single task for log capture, and created a workqueue
for the purpose of ensuring we had a high priority queue for low
latency. We can simply use the system_highpri_wq and avoid the
complication with creating our own admist the maze of mutexes.
(Currently we create the wq early before we even know we need it in
order to avoid trying to create it on demand while we hold the logging
mutex.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190713100016.8026-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 12 Jul 2019 19:29:53 +0000 (20:29 +0100)]
drm/i915/gt: Use intel_gt as the primary object for handling resets
Having taken the first step in encapsulating the functionality by moving
the related files under gt/, the next step is to start encapsulating by
passing around the relevant structs rather than the global
drm_i915_private. In this step, we pass intel_gt to intel_reset.c
Some platforms may have Modular FIA. If Modular FIA is used in the SOC,
then Display Driver will access the additional instances of
FIA based on pre-assigned offset in GTTMADDR space.
Each Modular FIA instance has its own IOSF Sideband Port ID
and it houses only 2 Type-C Port. In SOC that has more than
two Type-C Ports, there are multiple instances of Modular FIA.
Gunit will need to use different destination ID when it access
different pair of Type-C Port.
The DFLEXDPSP register has Modular FIA bit starting on Tiger Lake. If
Modular FIA is used in the SOC, this register bit exists in all the
instances of Modular FIA. IOM FW is required to program only the MF bit
in first FIA instance that houses the Type-C Port 0 and Port 1, for
Display Driver to read from.
v2 (Lucas):
- Move all accesses to FIA to be contained in intel_tc.c, along with
display_fia that is now called tc_phy_fia
- Save the fia instance number on intel_digital_port, so we don't have
to query if modular FIA is used on every access
v3 (Lucas): Make function static
v4 (Lucas): Move enum phy_fia to the header and use it in
intel_digital_port (suggested by Ville)
v5 (Lucas): Add comment about the mapping between FIA and TC port
(suggested by Stuart)
Chris Wilson [Fri, 12 Jul 2019 11:27:23 +0000 (12:27 +0100)]
drm/i915/gtt: Recursive ppgtt clear for gen8
With an explicit level, we can refactor the separate clear functions
as a simple recursive function. The additional knowledge of the level
allows us to spot when we can free an entire subtree at once.
Chris Wilson [Fri, 12 Jul 2019 11:27:22 +0000 (12:27 +0100)]
drm/i915/gtt: Recursive cleanup for gen8
With an explicit level, we can refactor the separate cleanup functions
as a simple recursive function. We take the opportunity to pass down the
size of each level so that we can deal with the different sizes of
top-level and avoid over allocating for 32/36-bit vm.
Chris Wilson [Fri, 12 Jul 2019 13:42:34 +0000 (14:42 +0100)]
drm/i915/display: Drop kerneldoc for 'intel_atomic_commit'
intel_atomic_commit() is not for use internally, but only as an entry
point from the core drm atomic helper (drm_atomic_commit).
Squelches the warning for:
drivers/gpu/drm/i915/display/intel_display.c:14148: warning: Function parameter or member '_state' not described in 'intel_atomic_commit'
drivers/gpu/drm/i915/display/intel_display.c:14148: warning: Excess function parameter 'state' description in 'intel_atomic_commit'
Ville Syrjälä [Tue, 28 May 2019 14:06:50 +0000 (17:06 +0300)]
drm/i915: Skip SINK_COUNT read on CH7511
CH7511 doesn't update SINK_COUNT properly so in order to detect
the device as connected we have to ignore SINK_COUNT.
In order to have access to the quirk list early enough we
must move the drm_dp_read_desc() call to happen earlier.
We can also skip re-reading this on eDP since we know it
won't change.
Cc: David S. <david@majinbuu.com> Cc: Peteris Rudzusiks <peteris.rudzusiks@gmail.com> Tested-by: Peteris Rudzusiks <peteris.rudzusiks@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105406 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528140650.19230-2-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com> #irc
Michal Wajdeczko [Fri, 12 Jul 2019 11:14:45 +0000 (11:14 +0000)]
drm/i915/guc: Turn on GuC/HuC auto mode
Using "enable_guc" modparam auto mode (-1) will let driver
decide on which platforms and in which configuration we want
to use GuC/HuC firmwares.
Today driver will enable HuC firmware authentication by GuC
only on Gen11+ platforms as HuC firmware is required to unlock
advanced video codecs in media driver.
Legacy platforms with GuC/HuC are not affected by this change
as for them driver still defaults to disabled(0) in auto mode.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190712111445.21040-3-michal.wajdeczko@intel.com
Michal Wajdeczko [Fri, 12 Jul 2019 11:14:44 +0000 (11:14 +0000)]
drm/i915/guc: Don't enable GuC/HuC in auto mode on pre-Gen11
We are about to change default setting of "enable_guc" modparam
from 0(disabled) to -1(auto). As we only want to turn on
GuC/HuC on Gen11+, keep it off for older gens.
Note that it would be still possible to enable GuC/HuC on these
old platforms using explicit "enable_guc=2" modparam.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190712111445.21040-2-michal.wajdeczko@intel.com
drm/i915: Propagate "_probe" function name suffix down
Similar to the "_release" and "_remove" cases, consequently replace
"_init" components of names of functions called from
i915_driver_probe() with "_probe" suffixes for better code readability.
drm/i915: Propagate "_remove" function name suffix down
Similar to the "_release" case, consistently replace mixed
"_cleanup"/"_fini"/"_fini_hw" components found in names of functions
called from i915_driver_remove() with "_remove" or "_driver_remove"
suffixes for better code readability.
drm/i915: Propagate "_release" function name suffix down
Replace mixed "_fini"/"_cleanup"/"_cleanup_hw" suffixes found in names
of functions called from i915_driver_release() with "_release" suffix
consistently. This provides better code readability, especially
helpful when trying to work out which phase the code is in.
Functions names starting with "i915_driver_", i.e., those defined in
drivers/gpu/dri/i915/i915_drv.c, just have their "cleanup" or "fini"
parts of their names replaced with the "_release" suffix, while names
of functions coming from other source files have been suffixed with
"_driver_release" to avoid ambiguity with other possible .release entry
points.
v2: early_probe pairs better with late_release (Chris)
v3: fix typo in commit message (Joonas)
drm/i915: Replace "_load" with "_probe" consequently
Use the "_probe" nomenclature not only in i915_driver_probe() helper
name but also in other related function / variable names for
consistency. Only the userspace exposed name of a related module
parameter is left untouched.
drm/i915: Rename "_load"/"_unload" to match PCI entry points
Current names of i915_driver_load/unload() functions originate in
legacy DRM stubs. Reduce nomenclature ambiguity by renaming them to
match their current use as helpers called from PCI entry points.
Chris Wilson [Fri, 12 Jul 2019 09:43:26 +0000 (10:43 +0100)]
drm/i915/gtt: Convert vm->scratch into an array
Each level has its own scratch. Make the levels more obvious by forgoing
the fancy similarly names and replace them with a number. 0 is the bottom
most level, the physical page used for actual data; 1+ are the page
directories.
projects / kernel.git / log