drivers: arm: gicv3: auto-detect presence of GIC600-AE
This patch adds the IIDR value for GIC600-AE to the gicv3_is_gic600()
helper function. This helps platforms supporting this version of the
GIC600 interrupt controller to function with the generic GIC driver.
Verified with tftf-validation test suite
******************************* Summary *******************************
> Test suite 'Framework Validation'
Passed
> Test suite 'Timer framework Validation'
Passed
=================================
Tests Skipped : 0
Tests Passed : 6
Tests Failed : 0
Tests Crashed : 0
Total tests : 6
=================================
NOTICE: Exiting tests.
corstone700: splitting the platform support into FVP and FPGA
This patch performs the following:
- Creating two corstone700 platforms under corstone700 board:
fvp and fpga
- Since the FVP and FPGA have IP differences, this commit provides a specific DTS for each platform
- The platform can be specified using the TARGET_PLATFORM Makefile variable
(possible values are: fvp or fpga)
- Allowing to use u-boot by:
- Enabling NEED_BL33 option
- Fixing non-secure image base: For no preloaded bl33 we want to
have the NS base set on shared ram. Setup a memory map region
for NS in shared map and set the bl33 address in the area.
- Setting the SYS_COUNTER_FREQ_IN_TICKS based on the selected
platform
- Setting ARM_MAP_SHARED_RAM and ARM_MAP_NS_SHARED_RAM to use MT_MEMORY
Change-Id: I4c8ac3387acb1693ab617bcccab00d80e340c163 Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Sami Mujawar [Thu, 23 Apr 2020 08:28:37 +0000 (09:28 +0100)]
Fix makefile to build on a Windows host PC
The TF-A firmware build system is capable of building on both Unix like
and Windows host PCs. The commit ID 7ff088 "Enable MTE support" updated
the Makefile to conditionally enable the MTE support if the AArch64
architecture revision was greater than 8.5. However, the Makefile changes
were dependent on shell commands that are only available on unix shells,
resulting in build failures on a Windows host PC.
This patch fixes the Makefile by using a more portable approach for
comparing the architecture revision.
Change-Id: Icb56cbecd8af5b0b9056d105970ff4a6edd1755a Signed-off-by: Sami Mujawar <sami.mujawar@arm.com>
plat/arm: Add assert for the valid address of dtb information
Added assert in the code to check valid address of dtb information
structure retrieved from fw_config device tree.
This patch fixes coverity defect:360213.
Also, removed conditional calling of "fconf_populate" as "fconf_populate"
function already checks the validity of the device tree address received
and go to panic in case of address is NULL.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ib83e4e84a95e2456a12c7a2bb3fe70461d882cba
Samuel Holland [Sun, 29 Dec 2019 22:12:12 +0000 (16:12 -0600)]
allwinner: Disable NS access to PRCM power control registers
The non-secure world has no business accessing the CPU power switches in
the PRCM; those are handled by TF-A or the SCP. Only allow access to the
clock control part of the PRCM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I657b97f4ea8a0073448ad3343fbc66ba168ed89e
Manish Pandey [Fri, 26 Jun 2020 13:59:38 +0000 (13:59 +0000)]
Merge changes Ib9c82b85,Ib348e097,I4dc315e4,I58a8ce44,Iebc03361, ... into integration
* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping the entire LLC to SRAM
plat: marvell: armada: add LLC SRAM CCU setup for AP806/AP807 platforms
plat: marvell: armada: reduce memory size reserved for FIP image
plat: marvell: armada: platform definitions cleanup
plat: marvell: armada: a8k: check CCU window state before loading MSS BL2
drivers: marvell: add CCU driver API for window state checking
drivers: marvell: align and extend llc macros
plat: marvell: a8k: move address config of cp1/2 to BL2
plat: marvell: armada: re-enable BL32_BASE definition
plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer
marvell: comphy: initialize common phy selector for AP mode
marvell: comphy: update rx_training procedure
plat: marvell: armada: configure amb for all CPs
plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs
Andre Przywara [Thu, 25 Jun 2020 12:10:13 +0000 (13:10 +0100)]
arm_fpga: Fix MPIDR topology checks
The plat_core_pos_by_mpidr() implementation for the Arm FPGA port has
some issues, which leads to problems when matching GICv3 redistributors
with cores:
- The power domain tree was not taking multithreading into account, so
we ended up with the wrong mapping between MPIDRs and core IDs.
- Before even considering an MPIDR, we try to make sure Aff2 is 0.
Unfortunately this is the cluster ID when the MT bit is set.
- We mask off the MT bit in MPIDR, before basing decisions on it.
- When detecting the MT bit, we are properly calculating the thread ID,
but don't account for the shift in the core and cluster ID checks.
Those problems lead to early rejections of MPIDRs values, in particular
when called from the GIC code. As a result, CPU_ON for secondary cores
was failing for most of the cores.
Fix this by properly handling the MT bit in plat_core_pos_by_mpidr(),
also pulling in FPGA_MAX_PE_PER_CPU when populating the power domain
tree.
Change-Id: I71b2255fc0d27bfe5806511df479ab38e4e33fc4 Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Merge changes from topic "fw_config_handoff" into integration
* changes:
doc: Update memory layout for firmware configuration area
plat/arm: Increase size of firmware configuration area
plat/arm: Load and populate fw_config and tb_fw_config
fconf: Handle error from fconf_load_config
plat/arm: Update the fw_config load call and populate it's information
fconf: Allow fconf to load additional firmware configuration
fconf: Clean confused naming between TB_FW and FW_CONFIG
tbbr/dualroot: Add fw_config image in chain of trust
cert_tool: Update cert_tool for fw_config image support
fiptool: Add fw_config in FIP
plat/arm: Rentroduce tb_fw_config device tree
Neoverse N1 erratum 1800710 is a Cat B erratum, present in older
revisions of the Neoverse N1 processor core. The workaround is to
set a bit in the ECTLR_EL1 system register, which disables allocation
of splintered pages in the L2 TLB.
This errata is explained in this SDEN:
https://static.docs.arm.com/sden885747/f/Arm_Neoverse_N1_MP050_Software_Developer_Errata_Notice_v21.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ie5b15c8bc3235e474a06a57c3ec70684361857a6
Cortex A77 erratum 1800714 is a Cat B erratum, present in older
revisions of the Cortex A77 processor core. The workaround is to
set a bit in the ECTLR_EL1 system register, which disables allocation
of splintered pages in the L2 TLB.
Since this is the first errata workaround implemented for Cortex A77,
this patch also adds the required cortex_a77_reset_func in the file
lib/cpus/aarch64/cortex_a77.S.
This errata is explained in this SDEN:
https://static.docs.arm.com/101992/0010/Arm_Cortex_A77_MP074_Software_Developer_Errata_Notice_v10.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I844de34ee1bd0268f80794e2d9542de2f30fd3ad
doc: Update memory layout for firmware configuration area
Captured the increase in firmware configuration area from
4KB to 8kB in memory layout document. Updated the documentation
to provide details about fw_config separately.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ifbec443ced479301be65827b49ff4fe447e9109f
plat/arm: Increase size of firmware configuration area
Increased the size of firmware configuration area to accommodate
all configs.
Updated maximum size of following bootloaders due to increase
in firmware configs size and addition of the code in the BL2.
1. Increased maximum size of BL2 for Juno platform in no
optimisation case.
2. Reduced maximum size of BL31 for fvp and Juno platform.
3. Reduced maximum size of BL32 for Juno platform.
Change-Id: Ifba0564df0d1fe86175bed9fae87fdcf013b1831 Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
plat/arm: Load and populate fw_config and tb_fw_config
Modified the code to do below changes:
1. Load tb_fw_config along with fw_config by BL1.
2. Populate fw_config device tree information in the
BL1 to load tb_fw_config.
3. In BL2, populate fw_config information to retrieve
the address of tb_fw_config and then tb_fw_config
gets populated using retrieved address.
4. Avoid processing of configuration file in case of error
value returned from "fw_config_load" function.
5. Updated entrypoint information for BL2 image so
that it's arg0 should point to fw_config address.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com> Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: Ife6f7b673a074e7f544ee3d1bda7645fd5b2886c
laurenw-arm [Thu, 6 Feb 2020 17:42:18 +0000 (11:42 -0600)]
fconf: Extract Timer clock freq from HW_CONFIG dtb
Extract Timer clock frequency from the timer node in
HW_CONFIG dtb. The first timer is a per-core architected timer attached
to a GIC to deliver its per-processor interrupts via PPIs.
Redirect security incident report to TrustedFirmware.org
All projects under the TrustedFirmware.org project now use the same
security incident process, therefore update the disclosure/vulnerability
reporting information in the TF-A documentation.
------------------------------------------------------------------------
/!\ IMPORTANT /!\
Please note that the email address to send these reports to has changed.
Please do *not* use trusted-firmware-security@arm.com anymore.
Similarly, the PGP key provided to encrypt emails to the security email
alias has changed as well. Please do *not* use the former one provided
in the TF-A source tree. It is recommended to remove it from your
keyring to avoid any mistake. Please use the new key provided on
TrustedFirmware.org from now on.
------------------------------------------------------------------------
plat/arm: Update the fw_config load call and populate it's information
Modified the code to do below changes:
1. Migrates the Arm platforms to the API changes introduced in the
previous patches by fixing the fconf_load_config() call.
2. Retrieve dynamically the address of tb_fw_config using fconf
getter api which is subsequently used to write mbedTLS heap
address and BL2 hash data in the tb_fw_config DTB.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com> Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>
Change-Id: I3c9d9345dcbfb99127c61d5589b4aa1532fbf4be
Moved BL2 configuration nodes from fw_config to newly
created tb_fw_config device tree.
fw_config device tree's main usage is to hold properties shared
across all BLx images.
An example is the "dtb-registry" node, which contains the
information about the other device tree configurations
(load-address, size).
Also, Updated load-address of tb_fw_config which is now located
after fw_config in SRAM.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: Ic398c86a4d822dacd55b5e25fd41d4fe3888d79a
Etienne Carriere [Tue, 23 Jun 2020 07:26:15 +0000 (09:26 +0200)]
stm32mp1: SP_MIN embeds Arm Architecture services
Embed Arch Architecture SMCCC services in stm32mp1 SP_MIN. This
service is needed by Linux kernel to setup the SMCCC conduit
used by its SCMI SMC transport driver.
stm32mp1: use last page of SYSRAM as SCMI shared memory
SCMI shared memory is used to exchange message payloads between
secure SCMI services and non-secure SCMI agents. It is mapped
uncached (device) mainly to conform to existing support in
the Linux kernel. Note that executive messages are mostly short
(few 32bit words) hence not using cache will not penalize much
performances.
Platform stm32mp1 shall configure ETZPC to harden properly the
secure and non-secure areas of the SYSRAM address space, that before
CPU accesses the shared memory when mapped non-secure.
This change defines STM32MP_SEC_SYSRAM_BASE/STM32MP_SEC_SYSRAM_SIZE and
STM32MP_NS_SYSRAM_BASE/STM32MP_NS_SYSRAM_SIZE.
Disable use of Neon VFP support for platform stm32mp1 when
building with SP_MIN runtime services as these can conflict with
non-secure world use of NEON support. This is preferred over a
systematic backup/restore of NEON context when switching
between non-secure and secure worlds.
When NEON support is disabled, this is done for both BL2 and BL32 as
build process uses common libraries built once for both binaries.
BL32/SP_MIN configures platform security hardening from the shared
resources driver. At the end of SP_MIN initialization, all shared
resources shall be assigned to secure or non-secure world by
drivers. A lock prevent from further change on the resource
assignation. By definition, resources not registered are assign
to non-secure world since not claimed by any component on the BL.
No functional change as all resources are currently in state
SHRES_UNREGISTERED hence assigned to non-secure world as prior
this change in stm32mp1_etzpc_early_setup() and
sp_min_platform_setup().
Etienne Carriere [Wed, 13 May 2020 08:13:54 +0000 (10:13 +0200)]
stm32mp1: shared resources: count GPIOZ bank pins
Get number of pins in the GPIOZ bank with helper function
fdt_get_gpio_bank_pin_count(). Save the value in RAM to prevent
parsing the FDT several time for the same information.
Define enum stm32mp_shres for platform stm32mp1. The enumerated
type defines all resources that can be assigned to secure or
non-secure worlds at run time for the platform.
STM32MP1 SoC includes peripheral interfaces that can be assigned to
the secure world, or that can be opened to the non-secure world.
This change introduces the basics of a driver that manages such
resources which assignation is done at run time. It currently offers
API functions that state whether a service exposed to non-secure
world has permission to access a targeted clock or reset controller.
Cortex A76 erratum 1800710 is a Cat B erratum, present in older
revisions of the Cortex A76 processor core. The workaround is to
set a bit in the ECTLR_EL1 system register, which disables allocation
of splintered pages in the L2 TLB.
This errata is explained in this SDEN:
https://static.docs.arm.com/sden885749/g/Arm_Cortex_A76_MP052_Software_Developer_Errata_Notice_v20.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ifc34f2e9e053dcee6a108cfb7df7ff7f497c9493
Cortex A76 erratum 1791580 is a Cat B erratum present in earlier
revisions of the Cortex A76. The workaround is to set a bit in the
implementation defined CPUACTLR2 register, which forces atomic store
operations to write-back memory to be performed in the L1 data cache.
This errata is explained in this SDEN:
https://static.docs.arm.com/sden885749/g/Arm_Cortex_A76_MP052_Software_Developer_Errata_Notice_v20.pdf
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Iefd58159b3f2e2286138993317b98e57dc361925
Manish Pandey [Mon, 22 Jun 2020 14:24:31 +0000 (14:24 +0000)]
Merge changes from topic "scmi-msg" into integration
* changes:
drivers/scmi-msg: smt entry points for incoming messages
drivers/scmi-msg: support for reset domain protocol
drivers/scmi-msg: support for clock protocol
drivers/scmi-msg: driver for processing scmi messages
It is desired to have the peripheral writes completed to clear the
interrupt condition and de-assert the interrupt request to GIC before
EOI write. Failing which spurious interrupt will occurred.
A barrier is needed to ensure peripheral register write transfers are
complete before EOI is done.
GICv2 memory mapped DEVICE nGnR(n)E writes are ordered from core point
of view. However these writes may pass over different interconnects,
bridges, buffers leaving some rare chances for the actual write to
complete out of order.
GICv3 ICC EOI system register writes have no ordering against nGnR(n)E
memory writes as they are over different interfaces.
Hence a dsb can ensure from core no writes are issued before the previous
writes are *complete*.
Varun Wadekar [Wed, 3 Jun 2020 04:16:00 +0000 (21:16 -0700)]
Tegra: sanity check NS address and size before use
This patch updates the 'bl31_check_ns_address()' helper function to
check that the memory address and size passed by the NS world are not
zero.
The helper fucntion also returns the error code as soon as it detects
inconsistencies, to avoid multiple error paths from kicking in for the
same input parameters.
drivers: marvell: add support for mapping the entire LLC to SRAM
Add llc_sram_enable() and llc_sram_disable() APIs to Marvell
cache_lls driver.
Add LLC_SRAM definition to Marvell common makefile - disabled
by the default.
Add description of LLC_SRAM flag to the build documentation.
Change-Id: Ib348e09752ce1206d29268ef96c9018b781db182 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Marcin Wojtas [Fri, 19 Jun 2020 15:51:08 +0000 (17:51 +0200)]
plat: marvell: armada: reduce memory size reserved for FIP image
It is not needed to reserve 64MB for FIP. Limit this to 4MB
for both supported Armada SoC families.
Change-Id: I58a8ce4408a646fe1afd3c1ea1ed54007c8d205d Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[Extract from bigger commit] Signed-off-by: Marcin Wojtas <mw@semihalf.com>
- Remove
TRUSTED_DRAM_BASE
TRUSTED_DRAM_SIZE
MARVELL_TRUSTED_SRAM_BASE
- Rename
PLAT_MARVELL_TRUSTED_DRAM_* -> PLAT_MARVELL_TRUSTED_RAM_*
PLAT_MARVELL_TRUSTED_SRAM_* -> MARVELL_TRUSTED_DRAM_*
MARVELL_MAP_SHARED_RAM -> MARVELL_MAP_SECURE_RAM
- Move
MARVELL_TRUSTED_DRAM_SIZE to marvell_def.h
- Enable MARVELL_MAP_SECURE_RAM region in BL2U memory map
- Add dependency of MARVELL_MAP_SHARED_RAM on LLC_SRAM
- Add minor style improvents
Change-Id: Iebc03361e4f88489af1597f54e137b27c241814c Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[Improve patch after rebase] Signed-off-by: Marcin Wojtas <mw@semihalf.com>
plat: marvell: armada: a8k: check CCU window state before loading MSS BL2
Make sure the current CCU window is not in use before adding
a new address map during MSS BL2 image load preparations.
At BL2 stage the CCU Win-2 points to DRAM. If additional mapping is
added to MSS BL2 stage initialization, the DDR entry will be destroyed
and lead to the system hang.
Change-Id: I215e83508acc37d54dab6954d791b9a74cc883ca Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Make all LLC-related macros to start with the same prefix
Add more LLC control registers definitions
This patch is a preparation step for LLC SRAM support
Change-Id: I0a4f0fc83e8ef35be93dd239a85f2a9f88d1ab19 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Ben Peled [Tue, 26 Mar 2019 17:06:24 +0000 (19:06 +0200)]
plat: marvell: a8k: move address config of cp1/2 to BL2
The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done after access to each CP is provided.
Moving the proper configuration from BL31 to BL2 solves it.
Change-Id: I44cf88dfd4ebf09130544332bfdd3d16ef2674ea Signed-off-by: Ben Peled <bpeled@marvell.com>
As a preparation to support proper loading the OPTEE OS image,
enable the BL32 specific defines in case the SPD is used.
On the occasion move two BL32-related macros to marvell_def.h
and fix BL32_LIMIT definition.
Change-Id: Id4e2d81833bc1895650cca8b0fc0bfc341cf77f3 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Signed-off-by: Marcin Wojtas <mw@semihalf.com>
plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer
The phy porting layer uses defaults defined in
"phy-default-porting-layer.h" when board specific file
"phy-porting-layer.h" is not found. Because of the regression the board
specific directory was not included, therefore all boards used default
parameters.
Change-Id: I66e5e6eb8a39cca5aeeb4de6dab2ceddc39c1e31 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
1) Relay only on rx training, remove parts responsible for tx training
(trx training).
2) Add extra steps e.g. preconfigure FFE before starting training.
3) Remove some unnecessary steps like RRBS31 loopback setting which
shouldn't be relevant for tx_training.
Change-Id: Ib1e8567714f9ce33578186a262c339aa4b1c51f2 Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Varun Wadekar [Wed, 3 Jun 2020 04:08:38 +0000 (21:08 -0700)]
Tegra: memctrl_v2: fixup sequence to resize video memory
The previous sequence used by the driver to program the new memory
aperture settings and clear the non-overlapping memory was faulty.
The sequence locked the non-overlapping regions twice, leading to
faults when trying to clear it.
This patch modifies the sequence to follow these steps:
* move the previous memory region to a new firewall register
* program the new memory aperture settings
* clean the non-overlapping memory
This patch also maps the non-overlapping memory as Device memory to
follow guidance from the arch. team.
Marcin Wojtas [Thu, 18 Jun 2020 17:50:47 +0000 (19:50 +0200)]
plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs
The Marvell Armada 37xx SoCs-based platforms contain a bit
awkward directory structure because the currently only one
supported PLAT and PLAT_FAMILY are the same. Modify the latter
to 'a3k' in order to improve it and keep plat/marvell/armada
tree more consistent:
plat/marvell/
├── armada
│ ├── a3k
│ │ ├── a3700
[...]
│ ├── a8k
│ │ ├── a70x0
[...]
Change-Id: I693a6ef88e6ce49a326a3328875c90bbc186066a Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Manish Pandey [Wed, 17 Jun 2020 19:44:51 +0000 (19:44 +0000)]
Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration
* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy
drivers/scmi-msg: smt entry points for incoming messages
This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
to the target platform services.
SMT refers to the shared memory management protocol which is used
to get/put message/response in shared memory. SMT is a 28byte header
stating shared memory state and exchanged protocol data.
The processing entry for a SCMI message can be a secure interrupt
or fastcall SMCCC invocation.
SMT description in this implementation is based on the OP-TEE
project [1] itself based in the SCP-firmware implementation [2].
drivers/scmi-msg: support for reset domain protocol
Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.
scmi_msg_get_rd_handler() sanitizes the message_id value
against any speculative use of reset domain ID as a index since by
SCMI specification, IDs are indices.
This implementation is based on the OP-TEE project implementation [2]
itself based on the SCP-firmware implementation [3] of the SCMI
protocol server side.
projects / arm-tf.git / log