Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 4bdf79d686b4 ("net: dsa: microchip: correct KSZ8795 static MAC table access") Signed-off-by: Sasha Levin <sashal@kernel.org>
If cls_bpf_offload errors out, we must also undo tcf_bind_filter that
was done before the error.
Fix that by calling tcf_unbind_filter in errout_parms.
Fixes: eadb41489fd2 ("net: cls_bpf: add support for marking filters as hardware-only") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the case of an update, when TCA_U32_LINK is set, u32_set_parms will
decrement the refcount of the ht_down (struct tc_u_hnode) pointer
present in the older u32 filter which we are replacing. However, if
u32_replace_hw_knode errors out, the update command fails and that
ht_down pointer continues decremented. To fix that, when
u32_replace_hw_knode fails, check if ht_down's refcount was decremented
and undo the decrement.
Fixes: d34e3e181395 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When u32_replace_hw_knode fails, we need to undo the tcf_bind_filter
operation done at u32_set_parms.
Fixes: d34e3e181395 ("net: cls_u32: Add support for skip-sw flag to tc u32 classifier.") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case an error occurred after mall_set_parms executed successfully, we
must undo the tcf_bind_filter call it issues.
Fix that by calling tcf_unbind_filter in err_replace_hw_filter label.
Fixes: ec2507d2a306 ("net/sched: cls_matchall: Fix error path") Signed-off-by: Victor Nogueira <victor@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This doesn't check how many bytes the simple_write_to_buffer() writes to
the buffer. The only thing that we know is that the first byte is
initialized and the last byte of the buffer is set to NUL. However
the middle bytes could be uninitialized.
There is no need to use simple_write_to_buffer(). This code does not
support partial writes but instead passes "pos = 0" as the starting
offset regardless of what the user passed as "*ppos". Just use the
copy_from_user() function and initialize the whole buffer.
Fixes: 671e0b90051e ("ASoC: SOF: Clone the trace code to ipc3-dtrace as fw_tracing implementation") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/74148292-ce4d-4e01-a1a7-921e6767da14@moroto.mountain Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the number of responses with status of STATUS_IO_TIMEOUT
exceeds a specified threshold (NUM_STATUS_IO_TIMEOUT), we reconnect
the connection. But we do not return the mid, or the credits
returned for the mid, or reduce the number of in-flight requests.
This bug could result in the server->in_flight count to go bad,
and also cause a leak in the mids.
This change moves the check to a few lines below where the
response is decrypted, even of the response is read from the
transform header. This way, the code for returning the mids
can be reused.
Also, the cifs_reconnect was reconnecting just the transport
connection before. In case of multi-channel, this may not be
what we want to do after several timeouts. Changed that to
reconnect the session and the tree too.
Also renamed NUM_STATUS_IO_TIMEOUT to a more appropriate name
MAX_STATUS_IO_TIMEOUT.
Fixes: 8e670f77c4a5 ("Handle STATUS_IO_TIMEOUT gracefully") Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the call to of_get_ethdev_address to mtk_add_mac which is part of
the probe function and can hence itself return -EPROBE_DEFER should
of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely
get rid of the mtk_init function.
The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced
in situations in which the NVMEM provider holding the MAC address has
not yet be loaded at the time mtk_eth_soc is initially probed. In this
case probing of mtk_eth_soc should be deferred instead of falling back
to use a random MAC address, so once the NVMEM provider becomes
available probing can be repeated.
Fixes: 656e705243fd ("net-next: mediatek: add support for MT7623 ethernet") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we create an L2 loop on a bridge in netns, we will see packets storm
even if STP is enabled.
# unshare -n
# ip link add br0 type bridge
# ip link add veth0 type veth peer name veth1
# ip link set veth0 master br0 up
# ip link set veth1 master br0 up
# ip link set br0 type bridge stp_state 1
# ip link set br0 up
# sleep 30
# ip -s link show br0
2: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether b6:61:98:1c:1c:b5 brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped missed mcast 95655376812861249 0 0 0 12861249 <-. Keep
TX: bytes packets errors dropped carrier collsns | increasing 1027834 11951 0 0 0 0 <-' rapidly
This is because llc_rcv() drops all packets in non-root netns and BPDU
is dropped.
Let's add extack warning when enabling STP in netns.
# unshare -n
# ip link add br0 type bridge
# ip link set br0 type bridge stp_state 1
Warning: bridge: STP does not work in non-root netns.
Note this commit will be reverted later when we namespacify the whole LLC
infra.
Fixes: e730c15519d0 ("[NET]: Make packet reception network namespace safe") Suggested-by: Harry Coin <hcoin@quietfountain.com> Link: https://lore.kernel.org/netdev/0f531295-e289-022d-5add-5ceffa0df9bc@quietfountain.com/ Suggested-by: Ido Schimmel <idosch@idosch.org> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the
field will be strictly contained within one word. However, this is not
guaranteed to be the case and it is possible for ALE field entries to span
across up to two words at the most.
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: db82173f23c5 ("netdev: driver: ethernet: add cpsw address lookup engine support") Signed-off-by: Tanmay Patil <t-patil@ti.com>
[s-vadapalli@ti.com: rephrased commit message and added Fixes tag] Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
I get sporadic timeouts from the driver when using the
MV88E6352. Reading the status again after the loop fixes the
problem: the operation is successful but goes undetected.
Some added prints show things like this:
[ 58.356209] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1b reg 0b, mask 8000, val 0000, data c000
[ 58.367487] mv88e6085 mdio_mux-0.1:00: Timeout waiting for
ATU op 4000, fid 0001
(...)
[ 61.826293] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1c reg 18, mask 8000, val 0000, data 9860
[ 61.837560] mv88e6085 mdio_mux-0.1:00: Timeout waiting
for PHY command 1860 to complete
The reason is probably not the commands: I think those are
mostly fine with the 50+50ms timeout, but the problem
appears when OpenWrt brings up several interfaces in
parallel on a system with 7 populated ports: if one of
them take more than 50 ms and waits one or more of the
others can get stuck on the mutex for the switch and then
this can easily multiply.
As we sleep and wait, the function loop needs a final
check after exiting the loop if we were successful.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Cc: Tobias Waldekranz <tobias@waldekranz.com> Fixes: 35da1dfd9484 ("net: dsa: mv88e6xxx: Improve performance of busy bit polling") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230712223405.861899-1-linus.walleij@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6eb4bd92c1ce ("kallsyms: strip LTO suffixes from static functions")
stripped all function/variable suffixes started with '.' regardless
of whether those suffixes are generated at LTO mode or not. In fact,
as far as I know, in LTO mode, when a static function/variable is
promoted to the global scope, '.llvm.<...>' suffix is added.
The existing mechanism breaks live patch for a LTO kernel even if
no <symbol>.llvm.<...> symbols are involved. For example, for the following
kernel symbols:
$ grep bpf_verifier_vlog /proc/kallsyms ffffffff81549f60 t bpf_verifier_vlog ffffffff8268b430 d bpf_verifier_vlog._entry ffffffff8282a958 d bpf_verifier_vlog._entry_ptr ffffffff82e12a1f d bpf_verifier_vlog.__already_done
'bpf_verifier_vlog' is a static function. '_entry', '_entry_ptr' and
'__already_done' are static variables used inside 'bpf_verifier_vlog',
so llvm promotes them to file-level static with prefix 'bpf_verifier_vlog.'.
Note that the func-level to file-level static function promotion also
happens without LTO.
Given a symbol name 'bpf_verifier_vlog', with LTO kernel, current mechanism will
return 4 symbols to live patch subsystem which current live patching
subsystem cannot handle it. With non-LTO kernel, only one symbol
is returned.
In [1], we have a lengthy discussion, the suggestion is to separate two
cases:
(1). new symbols with suffix which are generated regardless of whether
LTO is enabled or not, and
(2). new symbols with suffix generated only when LTO is enabled.
The cleanup_symbol_name() should only remove suffixes for case (2).
Case (1) should not be changed so it can work uniformly with or without LTO.
This patch removed LTO-only suffix '.llvm.<...>' so live patching and
tracing should work the same way for non-LTO kernel.
The cleanup_symbol_name() in scripts/kallsyms.c is also changed to have the same
filtering pattern so both kernel and kallsyms tool have the same
expectation on the order of symbols.
Fixes: 6eb4bd92c1ce ("kallsyms: strip LTO suffixes from static functions") Reported-by: Song Liu <song@kernel.org> Signed-off-by: Yonghong Song <yhs@fb.com> Reviewed-by: Zhen Lei <thunder.leizhen@huawei.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Acked-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230628181926.4102448-1-yhs@fb.com Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
LLVM appends various suffixes for local functions and variables, suffixes
observed:
- foo.llvm.[0-9a-f]+
- foo.[0-9a-f]+
Therefore, when CONFIG_LTO_CLANG=y, kallsyms_lookup_name() needs to
truncate the suffix of the symbol name before comparing the local function
or variable name.
Old implementation code:
- if (strcmp(namebuf, name) == 0)
- return kallsyms_sym_address(i);
- if (cleanup_symbol_name(namebuf) && strcmp(namebuf, name) == 0)
- return kallsyms_sym_address(i);
The preceding process is traversed by address from low to high. That is,
for those with the same name after the suffix is removed, the one with
the smallest address is returned first. Therefore, when sorting in the
tool, if the raw names are the same, they should be sorted by address in
ascending order.
Currently, to search for a symbol, we need to expand the symbols in
'kallsyms_names' one by one, and then use the expanded string for
comparison. It's O(n).
If we sort names in ascending order like addresses, we can also use
binary search. It's O(log(n)).
In order not to change the implementation of "/proc/kallsyms", the table
kallsyms_names[] is still stored in a one-to-one correspondence with the
address in ascending order.
Add array kallsyms_seqs_of_names[], it's indexed by the sequence number
of the sorted names, and the corresponding content is the sequence number
of the sorted addresses. For example:
Assume that the index of NameX in array kallsyms_seqs_of_names[] is 'i',
the content of kallsyms_seqs_of_names[i] is 'k', then the corresponding
address of NameX is kallsyms_addresses[k]. The offset in kallsyms_names[]
is get_symbol_offset(k).
Note that the memory usage will increase by (4 * kallsyms_num_syms)
bytes, the next two patches will reduce (1 * kallsyms_num_syms) bytes
and properly handle the case CONFIG_LTO_CLANG=y.
When SPI loopback transfer is performed, S3C64XX_SPI_MODE_SELF_LOOPBACK
bit still remained. It works as loopback even if the next transfer is
not spi loopback mode.
If not SPI_LOOP, needs to clear S3C64XX_SPI_MODE_SELF_LOOPBACK bit.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com> Fixes: ffb7bcd3b27e ("spi: s3c64xx: support loopback mode") Reviewed-by: Chanho Park <chanho61.park@samsung.com> Link: https://lore.kernel.org/r/20230711082020.138165-1-jaewon02.kim@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mirror_num_ret is allowed to be NULL, although it has to be set when
smap is set. Unfortunately that is not a well enough specifiable
invariant for static type checkers, so add a NULL check to make sure they
are fine.
Fixes: 03793cbbc80f ("btrfs: add fast path for single device io in __btrfs_map_block") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-L only specifies the search path for libraries directly provided in the
link line with -l. Because -lopencsd isn't specified, it's only linked
because it's a dependency of -lopencsd_c_api. Dependencies like this are
resolved using the default system search paths or -rpath-link=... rather
than -L. This means that compilation only works if OpenCSD is installed
to the system rather than provided with the CSLIBS (-L) option.
This could be fixed by adding -Wl,-rpath-link=$(CSLIBS) but that is less
conventional than just adding -lopencsd to the link line so that it uses
-L. -lopencsd seems to have been removed in commit ed17b1914978eddb
("perf tools: Drop requirement for libstdc++.so for libopencsd check")
because it was thought that there was a chance compilation would work
even if it didn't exist, but I think that only applies to libstdc++ so
there is no harm to add it back. libopencsd.so and libopencsd_c_api.so
would always exist together.
Testing
=======
The following scenarios now all work:
* Cross build with OpenCSD installed
* Cross build using CSLIBS=...
* Native build with OpenCSD installed
* Native build using CSLIBS=...
* Static cross build with OpenCSD installed
* Static cross build with CSLIBS=...
Committer testing:
⬢[acme@toolbox perf-tools]$ alias m
alias m='make -k BUILD_BPF_SKEL=1 CORESIGHT=1 O=/tmp/build/perf-tools -C tools/perf install-bin && git status && perf test python ; perf record -o /dev/null sleep 0.01 ; perf stat --null sleep 0.01'
⬢[acme@toolbox perf-tools]$ ldd ~/bin/perf | grep csd
libopencsd_c_api.so.1 => /lib64/libopencsd_c_api.so.1 (0x00007fd49c44e000)
libopencsd.so.1 => /lib64/libopencsd.so.1 (0x00007fd49bd56000)
⬢[acme@toolbox perf-tools]$ cat /etc/redhat-release
Fedora release 36 (Thirty Six)
⬢[acme@toolbox perf-tools]$
Fixes: ed17b1914978eddb ("perf tools: Drop requirement for libstdc++.so for libopencsd check") Reported-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Signed-off-by: James Clark <james.clark@arm.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Tested-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: coresight@lists.linaro.org Closes: https://lore.kernel.org/linux-arm-kernel/56905d7a-a91e-883a-b707-9d5f686ba5f1@arm.com/ Link: https://lore.kernel.org/all/36cc4dc6-bf4b-1093-1c0a-876e368af183@kleine-koenig.org/ Link: https://lore.kernel.org/r/20230707154546.456720-1-james.clark@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove unnecessary release_mem_region from the error path to prevent
mem region from being released twice, which could avoid resource leak
or other unexpected issues.
If the prepend byte count field starts at bit 8, and the next defined
bit is SPI_CMD_ONE_BYTE at bit 11, it can be at most 3 bits wide, and
thus the max value is 7, not 15.
Fixes: b17de076062a ("spi/bcm63xx: work around inability to keep CS up") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Link: https://lore.kernel.org/r/20230629071453.62024-1-jonas.gorski@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, sd1 and sd0 have unique subnode names 'sd1_mux' and 'sd0_mux'.
If we change these to non-unique subnode names such as 'mux' this can
lead to the below conflict as the RZ/G2L pin control driver considers
only the names of the subnodes.
pinctrl-rzg2l 11030000.pinctrl: pin P47_0 already requested by 11c00000.mmc; cannot claim for 11c10000.mmc
pinctrl-rzg2l 11030000.pinctrl: pin-376 (11c10000.mmc) status -22
pinctrl-rzg2l 11030000.pinctrl: could not request pin 376 (P47_0) from group mux on device pinctrl-rzg2l
renesas_sdhi_internal_dmac 11c10000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Based on the work done by Geert for the RZ/V2M pinctrl driver.
The eMMC and SDHI pin control configuration nodes in DT have subnodes
with the same names ("data" and "ctrl"). As the RZ/V2M pin control
driver considers only the names of the subnodes, this leads to
conflicts:
pinctrl-rzv2m b6250000.pinctrl: pin P8_2 already requested by 85000000.mmc; cannot claim for 85020000.mmc
pinctrl-rzv2m b6250000.pinctrl: pin-130 (85020000.mmc) status -22
renesas_sdhi_internal_dmac 85020000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Destroying psi trigger in cgroup_file_release causes UAF issues when
a cgroup is removed from under a polling process. This is happening
because cgroup removal causes a call to cgroup_file_release while the
actual file is still alive. Destroying the trigger at this point would
also destroy its waitqueue head and if there is still a polling process
on that file accessing the waitqueue, it will step on the freed pointer:
do_select
vfs_poll
do_rmdir
cgroup_rmdir
kernfs_drain_open_files
cgroup_file_release
cgroup_pressure_release
psi_trigger_destroy
wake_up_pollfree(&t->event_wait)
// vfs_poll is unblocked
synchronize_rcu
kfree(t)
poll_freewait -> UAF access to the trigger's waitqueue head
Patch [1] fixed this issue for epoll() case using wake_up_pollfree(),
however the same issue exists for synchronous poll() case.
The root cause of this issue is that the lifecycles of the psi trigger's
waitqueue and of the file associated with the trigger are different. Fix
this by using kernfs_generic_poll function when polling on cgroup-specific
psi triggers. It internally uses kernfs_open_node->poll waitqueue head
with its lifecycle tied to the file's lifecycle. This also renders the
fix in [1] obsolete, so revert it.
[1] commit c2dbe32d5db5 ("sched/psi: Fix use-after-free in ep_remove_wait_queue()")
PSI offers 2 mechanisms to get information about a specific resource
pressure. One is reading from /proc/pressure/<resource>, which gives
average pressures aggregated every 2s. The other is creating a pollable
fd for a specific resource and cgroup.
The trigger creation requires CAP_SYS_RESOURCE, and gives the
possibility to pick specific time window and threshold, spawing an RT
thread to aggregate the data.
Systemd would like to provide containers the option to monitor pressure
on their own cgroup and sub-cgroups. For example, if systemd launches a
container that itself then launches services, the container should have
the ability to poll() for pressure in individual services. But neither
the container nor the services are privileged.
This patch implements a mechanism to allow unprivileged users to create
pressure triggers. The difference with privileged triggers creation is
that unprivileged ones must have a time window that's a multiple of 2s.
This is so that we can avoid unrestricted spawning of rt threads, and
use instead the same aggregation mechanism done for the averages, which
runs independently of any triggers.
Suggested-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Domenico Cerasuolo <cerasuolodomenico@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Link: https://lore.kernel.org/r/20230330105418.77061-5-cerasuolodomenico@gmail.com
Stable-dep-of: aff037078eca ("sched/psi: use kernfs polling functions for PSI trigger polling") Signed-off-by: Sasha Levin <sashal@kernel.org>
This change moves update_total flag out of update_triggers function,
currently called only in psi_poll_work.
In the next patch, update_triggers will be called also in psi_avgs_work,
but the total update information is specific to psi_poll_work.
Returning update_total value to the caller let us avoid differentiating
the implementation of update_triggers for different aggregators.
Suggested-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Domenico Cerasuolo <cerasuolodomenico@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Link: https://lore.kernel.org/r/20230330105418.77061-4-cerasuolodomenico@gmail.com
Stable-dep-of: aff037078eca ("sched/psi: use kernfs polling functions for PSI trigger polling") Signed-off-by: Sasha Levin <sashal@kernel.org>
Pavan reported a problem that PSI avgs_work idle shutoff is not
working at all. Because PSI_NONIDLE condition would be observed in
psi_avgs_work()->collect_percpu_times()->get_recent_times() even if
only the kworker running avgs_work on the CPU.
Although commit 1b69ac6b40eb ("psi: fix aggregation idle shut-off")
avoided the ping-pong wake problem when the worker sleep, psi_avgs_work()
still will always re-arm the avgs_work, so shutoff is not working.
This patch changes to use PSI_STATE_RESCHEDULE to flag whether to
re-arm avgs_work in get_recent_times(). For the current CPU, we re-arm
avgs_work only when (NR_RUNNING > 1 || NR_IOWAIT > 0 || NR_MEMSTALL > 0),
for other CPUs we can just check PSI_NONIDLE delta. The new flag
is only used in psi_avgs_work(), so we check in get_recent_times()
that current_work() is avgs_work.
One potential problem is that the brief period of non-idle time
incurred between the aggregation run and the kworker's dequeue will
be stranded in the per-cpu buckets until avgs_work run next time.
The buckets can hold 4s worth of time, and future activity will wake
the avgs_work with a 2s delay, giving us 2s worth of data we can leave
behind when shut off the avgs_work. If the kworker run other works after
avgs_work shut off and doesn't have any scheduler activities for 2s,
this maybe a problem.
When checking whether a recently used CPU can be a potential idle
candidate, recent_used_cpu should be used to test p->cpus_ptr as
p->recent_used_cpu is not equal to recent_used_cpu and candidate
decision is made based on recent_used_cpu here.
Fixes: 89aafd67f28c ("sched/fair: Use prev instead of new target as recent_used_cpu") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Phil Auld <pauld@redhat.com> Acked-by: Mel Gorman <mgorman@suse.de> Link: https://lore.kernel.org/r/20230620080747.359122-1-linmiaohe@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Closing GPR port before graph close can result in un handled notifications
from DSP, this results in spam of errors from GPR driver as there is no
one to handle these notification at that point in time.
Fix this by closing GPR port after graph close is finished.
For invalid dai id, instead of returning -EINVAL
return bytes count as zero in acp_get_byte_count() function.
Fixes: 623621a9f9e1 ("ASoC: amd: Add common framework to support I2S on ACP SOC") Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com> Link: https://lore.kernel.org/r/20230626105356.2580125-6-Vijendar.Mukunda@amd.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hclge_debugfs.c:90:25: warning: 'strncpy' output truncated before
terminating nul copying as many bytes from a string as its length
[-Wstringop-truncation]
strncpy(pos, result[i], strlen(result[i]));
strncpy() use src-length as copy-length, it may result in
dest-buf overflow.
So,this patch add some values check to avoid this issue.
Signed-off-by: Hao Chen <chenhao418@huawei.com> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/lkml/202207170606.7WtHs9yS-lkp@intel.com/T/ Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a setup where a Thunderbolt hub connects to Ethernet and a display
through USB Type-C, users may experience a hung task timeout when they
remove the cable between the PC and the Thunderbolt hub.
This is because the igb_down function is called multiple times when
the Thunderbolt hub is unplugged. For example, the igb_io_error_detected
triggers the first call, and the igb_remove triggers the second call.
The second call to igb_down will block at napi_synchronize.
Here's the call trace:
__schedule+0x3b0/0xddb
? __mod_timer+0x164/0x5d3
schedule+0x44/0xa8
schedule_timeout+0xb2/0x2a4
? run_local_timers+0x4e/0x4e
msleep+0x31/0x38
igb_down+0x12c/0x22a [igb 6615058754948bfde0bf01429257eb59f13030d4]
__igb_close+0x6f/0x9c [igb 6615058754948bfde0bf01429257eb59f13030d4]
igb_close+0x23/0x2b [igb 6615058754948bfde0bf01429257eb59f13030d4]
__dev_close_many+0x95/0xec
dev_close_many+0x6e/0x103
unregister_netdevice_many+0x105/0x5b1
unregister_netdevice_queue+0xc2/0x10d
unregister_netdev+0x1c/0x23
igb_remove+0xa7/0x11c [igb 6615058754948bfde0bf01429257eb59f13030d4]
pci_device_remove+0x3f/0x9c
device_release_driver_internal+0xfe/0x1b4
pci_stop_bus_device+0x5b/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_and_remove_bus_device+0x12/0x19
pciehp_unconfigure_device+0x76/0xe9
pciehp_disable_slot+0x6e/0x131
pciehp_handle_presence_or_link_change+0x7a/0x3f7
pciehp_ist+0xbe/0x194
irq_thread_fn+0x22/0x4d
? irq_thread+0x1fd/0x1fd
irq_thread+0x17b/0x1fd
? irq_forced_thread_fn+0x5f/0x5f
kthread+0x142/0x153
? __irq_get_irqchip_state+0x46/0x46
? kthread_associate_blkcg+0x71/0x71
ret_from_fork+0x1f/0x30
In this case, igb_io_error_detected detaches the network interface
and requests a PCIE slot reset, however, the PCIE reset callback is
not being invoked and thus the Ethernet connection breaks down.
As the PCIE error in this case is a non-fatal one, requesting a
slot reset can be avoided.
This patch fixes the task hung issue and preserves Ethernet
connection by ignoring non-fatal PCIE errors.
Signed-off-by: Ying Hsu <yinghsu@chromium.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230620174732.4145155-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel Killer AX1675i/s with device id 51f1 would show
"No config found for PCI dev 51f1/1672" in dmesg and refuse to work.
Add the new device id 51F1 for 1675i/s to fix the issue.
Roee reported various hard-to-debug crashes with pings in
EHT aggregation scenarios. Enabling KASAN showed that we
access the BAID allocation out of bounds, and looking at
the code a bit shows that since the reorder buffer entry
(struct iwl_mvm_reorder_buf_entry) is 128 bytes if debug
such as lockdep is enabled, then staring from an agg size
512 we overflow the size calculation, and allocate a much
smaller structure than we should, causing slab corruption
once we initialize this.
-Wstringop-overflow is legitimately warning us about extra_size
pontentially being zero at some point, hence potenially ending
up _allocating_ zero bytes of memory for extra pointer and then
trying to access such object in a call to copy_from_user().
Fix this by adding a sanity check to ensure we never end up
trying to allocate zero bytes of data for extra pointer, before
continue executing the rest of the code in the function.
Address the following -Wstringop-overflow warning seen when built
m68k architecture with allyesconfig configuration:
from net/wireless/wext-core.c:11:
In function '_copy_from_user',
inlined from 'copy_from_user' at include/linux/uaccess.h:183:7,
inlined from 'ioctl_standard_iw_point' at net/wireless/wext-core.c:825:7:
arch/m68k/include/asm/string.h:48:25: warning: '__builtin_memset' writing 1 or more bytes into a region of size 0 overflows the destination [-Wstringop-overflow=]
48 | #define memset(d, c, n) __builtin_memset(d, c, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/uaccess.h:153:17: note: in expansion of macro 'memset'
153 | memset(to + (n - res), 0, res);
| ^~~~~~
In function 'kmalloc',
inlined from 'kzalloc' at include/linux/slab.h:694:9,
inlined from 'ioctl_standard_iw_point' at net/wireless/wext-core.c:819:10:
include/linux/slab.h:577:16: note: at offset 1 into destination object of size 0 allocated by '__kmalloc'
577 | return __kmalloc(size, flags);
| ^~~~~~~~~~~~~~~~~~~~~~
This help with the ongoing efforts to globally enable
-Wstringop-overflow.
devlink_port_type_warn is scheduled for port devlink and warning
when the port type is not set. But from this warning it is not easy
found out which device (driver) has no devlink port set.
Implement 64 bit per cpu stats to fix the overflow of netdev->stats
on 32 bit platforms. To simplify the code, we use net core
pcpu_sw_netstats infrastructure. One small drawback is some memory
overhead because litex uses just one queue, but we allocate the
counters per cpu.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Gabriel Somlo <gsomlo@gmail.com> Link: https://lore.kernel.org/r/20230614162035.300-1-jszhang@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated for firmware pdev, vdev and beacon statistics
are not released during rmmod.
Fix it by calling ath11k_fw_stats_free() function before hardware
unregister.
While at it, avoid calling ath11k_fw_stats_free() while processing
the firmware stats received in the WMI event because the local list
is getting spliced and reinitialised and hence there are no elements
in the list after splicing.
The Intel Mount Evans SoC's Integrated Management Complex uses the SPI
controller for access to a NOR SPI FLASH. However, the SoC doesn't
provide a mechanism to override the native chip select signal.
This driver doesn't use DMA for memory operations when a chip select
override is not provided due to the native chip select timing behavior.
As a result no DMA configuration is done for the controller and this
configuration is not tested.
The controller also has an errata where a full TX FIFO can result in
data corruption. The suggested workaround is to never completely fill
the FIFO. The TX FIFO has a size of 32 so the fifo_len is set to 31.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20230606145402.474866-2-abe.kohandel@intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sometimes board-2.bin does not have the regdb data which matched the
parameters such as vendor, device, subsystem-vendor, subsystem-device
and etc. Add default regdb data with 'bus=%s' into board-2.bin for
WCN6855, then ath11k use 'bus=pci' to search regdb data in board-2.bin
for WCN6855.
kernel: [ 122.515808] ath11k_pci 0000:03:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
kernel: [ 122.517240] ath11k_pci 0000:03:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 6179564
kernel: [ 122.517280] ath11k_pci 0000:03:00.0: failed to fetch regdb data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262 from ath11k/WCN6855/hw2.0/board-2.bin
kernel: [ 122.517464] ath11k_pci 0000:03:00.0: boot using board name 'bus=pci'
kernel: [ 122.518901] ath11k_pci 0000:03:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 6179564
kernel: [ 122.518915] ath11k_pci 0000:03:00.0: board name
kernel: [ 122.518917] ath11k_pci 0000:03:00.0: 00000000: 62 75 73 3d 70 63 69 bus=pci
kernel: [ 122.518918] ath11k_pci 0000:03:00.0: boot found match regdb data for name 'bus=pci'
kernel: [ 122.518920] ath11k_pci 0000:03:00.0: boot found regdb data for 'bus=pci'
kernel: [ 122.518921] ath11k_pci 0000:03:00.0: fetched regdb
This is a preparatory commit to replace `lock_sock_fast` with
`lock_sock`,and facilitate BPF programs executed from the TCP sockets
iterator to be able to destroy TCP sockets using the bpf_sock_destroy
kfunc (implemented in follow-up commits).
Previously, BPF TCP iterator was acquiring the sock lock with BH
disabled. This led to scenarios where the sockets hash table bucket lock
can be acquired with BH enabled in some path versus disabled in other.
In such situation, kernel issued a warning since it thinks that in the
BH enabled path the same bucket lock *might* be acquired again in the
softirq context (BH disabled), which will lead to a potential dead lock.
Since bpf_sock_destroy also happens in a process context, the potential
deadlock warning is likely a false alarm.
Here is a snippet of annotated stack trace that motivated this change:
lock_acquire+0xcd/0x330
_raw_spin_lock+0x33/0x40
------> Acquire (bucket) lhash2.lock with BH disabled
inet_unhash+0x9a/0x110
tcp_set_state+0x6a/0x210
tcp_abort+0x10d/0x200
bpf_prog_6793c5ca50c43c0d_iter_tcp6_server+0xa4/0xa9
bpf_iter_run_prog+0x1ff/0x340
------> lock_sock_fast that acquires sock lock with BH disabled
bpf_iter_tcp_seq_show+0xca/0x190
bpf_seq_read+0x177/0x450
```
Also, Yonghong reported a deadlock for non-listening TCP sockets that
this change resolves. Previously, `lock_sock_fast` held the sock spin
lock with BH which was again being acquired in `tcp_abort`:
KCSAN reported a data-race when accessing node->ref.
Although node->ref does not have to be accurate,
take this chance to use a more common READ_ONCE() and WRITE_ONCE()
pattern instead of data_race().
There is an existing bpf_lru_node_is_ref() and bpf_lru_node_set_ref().
This patch also adds bpf_lru_node_clear_ref() to do the
WRITE_ONCE(node->ref, 0) also.
==================================================================
BUG: KCSAN: data-race in __bpf_lru_list_rotate / __htab_lru_percpu_map_update_elem
read to 0xffff888137038deb of 1 bytes by task 11241 on cpu 0:
bpf_lru_node_set_ref kernel/bpf/bpf_lru_list.h:70 [inline]
__htab_lru_percpu_map_update_elem+0x2f1/0x820 kernel/bpf/hashtab.c:1332
bpf_percpu_hash_update+0x5e/0x90 kernel/bpf/hashtab.c:2313
bpf_map_update_value+0x2a9/0x370 kernel/bpf/syscall.c:200
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1687
bpf_map_do_batch+0x2d9/0x3d0 kernel/bpf/syscall.c:4534
__sys_bpf+0x338/0x810
__do_sys_bpf kernel/bpf/syscall.c:5096 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5094 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5094
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x01 -> 0x00
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 11241 Comm: syz-executor.3 Not tainted 6.3.0-rc7-syzkaller-00136-g6a66fdd29ea1 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
==================================================================
Reported-by: syzbot+ebe648a84e8784763f82@syzkaller.appspotmail.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/r/20230511043748.1384166-1-martin.lau@linux.dev Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Further investigation shows that the warning is superfluous, the migration
disabled task is just going to be migrated to its current running CPU.
This is because that on load balance if the dst_cpu is not allowed by the
task, we'll re-select a new_dst_cpu as a candidate. If no task can be
balanced to dst_cpu we'll try to balance the task to the new_dst_cpu
instead. In this case when the migration disabled task is not on CPU it
only allows to run on its current CPU, load balance will select its
current CPU as new_dst_cpu and later triggers the warning above.
The new_dst_cpu is chosen from the env->dst_grpmask. Currently it
contains CPUs in sched_group_span() and if we have overlapped groups it's
possible to run into this case. This patch makes env->dst_grpmask of
group_balance_mask() which exclude any CPUs from the busiest group and
solve the issue. For balancing in a domain with no overlapped groups
the behaviour keeps same as before.
Suggested-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lore.kernel.org/r/20230530082507.10444-1-yangyicong@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The per-CPU rcu_data structure's ->cpu_no_qs.b.exp field is updated
only on the instance corresponding to the current CPU, but can be read
more widely. Unmarked accesses are OK from the corresponding CPU, but
only if interrupts are disabled, given that interrupt handlers can and
do modify this field.
Unfortunately, although the load from rcu_preempt_deferred_qs() is always
carried out from the corresponding CPU, interrupts are not necessarily
disabled. This commit therefore upgrades this load to READ_ONCE.
Similarly, the diagnostic access from synchronize_rcu_expedited_wait()
might run with interrupts disabled and from some other CPU. This commit
therefore marks this load with data_race().
Finally, the C-language access in rcu_preempt_ctxt_queue() is OK as
is because interrupts are disabled and this load is always from the
corresponding CPU. This commit adds a comment giving the rationale for
this access being safe.
This data race was reported by KCSAN. Not appropriate for backporting
due to failure being unlikely.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Dell Studio 1569 predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native intel_backlight interface which
does work properly.
Reported-by: raycekarneal <raycekarneal@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller reported an issue where txBegin may be called
on a superblock in a read-only mounted filesystem which leads
to NULL pointer deref. This could be solved by checking if
the filesystem is read-only before calling txBegin, and returning
with appropiate error code.
Zero-length arrays are deprecated, and we are replacing them with flexible
array members instead. So, replace zero-length array with flexible-array
member in struct memmap.
Address the following warning found after building (with GCC-13) mips64
with decstation_64_defconfig:
In function 'rex_setup_memory_region',
inlined from 'prom_meminit' at arch/mips/dec/prom/memory.c:91:3:
arch/mips/dec/prom/memory.c:72:31: error: array subscript i is outside array bounds of 'unsigned char[0]' [-Werror=array-bounds=]
72 | if (bm->bitmap[i] == 0xff)
| ~~~~~~~~~~^~~
In file included from arch/mips/dec/prom/memory.c:16:
./arch/mips/include/asm/dec/prom.h: In function 'prom_meminit':
./arch/mips/include/asm/dec/prom.h:73:23: note: while referencing 'bitmap'
73 | unsigned char bitmap[0];
This helps with the ongoing efforts to globally enable -Warray-bounds.
The bug occurs when the dbAllocDmapLev()function attempts to access
dp->tree.stree[leafidx + LEAFIND] while the leafidx value is negative.
To rectify this, the patch introduces a safeguard within the
dbAllocDmapLev() function. A check has been added to verify if leafidx is
negative. If it is, the function immediately returns an I/O error, preventing
any further execution that could potentially cause harm.
For filenames that begin with . and are between 2 and 5 characters long,
UDF charset conversion code would read uninitialized memory in the
output buffer. The only practical impact is that the name may be prepended a
"unification hash" when it is not actually needed but still it is good
to fix this.
Porting overlayfs to the new amount api I started experiencing random
crashes that couldn't be explained easily. So after much debugging and
reasoning it became clear that struct ovl_entry requires the point to
struct vfsmount to be the first member and of type struct vfsmount.
During the port I added a new member at the beginning of struct
ovl_entry which broke all over the place in the form of random crashes
and cache corruptions. While there's a comment in ovl_free_fs() to the
effect of "Hack! Reuse ofs->layers as a vfsmount array before freeing
it" there's no such comment on struct ovl_entry which makes this easy to
trip over.
Add a comment and two static asserts for both the offset and the type of
pointer in struct ovl_entry.
Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
HP Elite Presenter Mouse HID Record Descriptor shows
two mouses (Repord ID 0x1 and 0x2), one keypad (Report ID 0x5),
two Consumer Controls (Report IDs 0x6 and 0x3).
Previous to this commit it registers one mouse, one keypad
and one Consumer Control, and it was usable only as a
digitl laser pointer (one of the two mouses). This patch defines
the 464a USB device ID and enables the HID_QUIRK_MULTI_INPUT
quirk for it, allowing to use the device both as a mouse
and a digital laser pointer.
Above issue may happens as follows:
ProcessA ProcessB ProcessC
sys_fsconfig
vfs_fsconfig_locked
reconfigure_super
ext4_remount
dquot_suspend -> suspend all type quota
__dquot_initialize
__dquot_initialize
dqget
if (!test_bit(DQ_ACTIVE_B, &dquot->dq_flags))
ext4_acquire_dquot
-> Return error DQ_ACTIVE_B flag isn't set
dquot_disable
invalidate_dquots
if (atomic_read(&dquot->dq_count))
dqgrab
WARN_ON_ONCE(!test_bit(DQ_ACTIVE_B, &dquot->dq_flags))
-> Trigger warning
In the above scenario, 'dquot->dq_flags' has no DQ_ACTIVE_B is normal when
dqgrab().
To solve above issue just replace the dqgrab() use in invalidate_dquots() with
atomic_inc(&dquot->dq_count).
Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230605140731.2427629-3-yebin10@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When add_dquot_ref() fails (usually due to IO error or ENOMEM), we want
to disable quotas we are trying to enable. However dquot_disable() call
was passed just the flags we are enabling so in case flags ==
DQUOT_USAGE_ENABLED dquot_disable() call will just fail with EINVAL
instead of properly disabling quotas. Fix the problem by always passing
DQUOT_LIMITS_ENABLED | DQUOT_USAGE_ENABLED to dquot_disable() in this
case.
Reported-and-tested-by: Ye Bin <yebin10@huawei.com> Reported-by: syzbot+e633c79ceaecbf479854@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230605140731.2427629-2-yebin10@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The type of size is unsigned, if size is 0x40000000, there will be an
integer overflow, size will be zero after size *= sizeof(uint32_t),
will cause uninitialized memory to be referenced later
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: hackyzh002 <hackyzh002@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When run on a file system where the inline_data feature has been
enabled, xfstests generic/269, generic/270, and generic/476 cause ext4
to emit error messages indicating that inline directory entries are
corrupted. This occurs because the inline offset used to locate
inline directory entries in the inode body is not updated when an
xattr in that shared region is deleted and the region is shifted in
memory to recover the space it occupied. If the deleted xattr precedes
the system.data attribute, which points to the inline directory entries,
that attribute will be moved further up in the region. The inline
offset continues to point to whatever is located in system.data's former
location, with unfortunate effects when used to access directory entries
or (presumably) inline data in the inode body.
Make sure that the soundwire device used for register accesses has been
enumerated and initialised before trying to read the codec variant
during component probe.
This specifically avoids interpreting (a masked and shifted) -EBUSY
errno as the variant:
wcd938x_codec audio-codec: ASoC: error at soc_component_read_no_lock on audio-codec for register: [0x000034b0] -16
in case the soundwire device has not yet been initialised, which in turn
prevents some headphone controls from being registered.
Byte mask for channel-1 of stream-1 is not getting enabled and this
causes failures during AMX use cases. This happens because the byte
map value 0 matches the byte map array and put() callback returns
without enabling the corresponding bits in the byte mask.
AMX supports 4 input streams and each stream can take a maximum of
16 channels. Each byte in the output frame is uniquely mapped to a
byte in one of these 4 inputs. This mapping is done with the help of
byte map array via user space control setting. The byte map array
size in the driver is 16 and each array element is of size 4 bytes.
This corresponds to 64 byte map values.
Each byte in the byte map array can have any value between 0 to 255
to enable the corresponding bits in the byte mask. The value 256 is
used as a way to disable the byte map. However the byte map array
element cannot store this value. The put() callback disables the byte
mask for 256 value and byte map value is reset to 0 for this case.
This causes problems during subsequent runs since put() callback,
for value of 0, just returns without enabling the byte mask. In short,
the problem is coming because 0 and 256 control values are stored as
0 in the byte map array.
Right now fix the put() callback by actually looking at the byte mask
array state to identify if any change is needed and update the fields
accordingly. The get() callback needs an update as well to return the
correct control value that user has set before. Note that when user
sets 256, the value is stored as 0 and byte mask is disabled. So byte
mask state is used to either return 256 or the value from byte map
array.
Given above, this looks bit complicated and all this happens because
the byte map array is tightly packed and cannot actually store the 256
value. Right now the priority is to fix the existing failure and a TODO
item is put to improve this logic.
Fixes: 8db78ace1ba8 ("ASoC: tegra: Fix kcontrol put callback in AMX") Cc: stable@vger.kernel.org Signed-off-by: Sheetal <sheetal@nvidia.com> Reviewed-by: Mohan Kumar D <mkumard@nvidia.com> Reviewed-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1688015537-31682-2-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2cb1e0259f50 ("ASoC: cs42l51: re-hook of_match_table
pointer"), 9 years ago, some random guy fixed the cs42l51 after it was
split into a core part and an I2C part to properly match based on a
Device Tree compatible string.
However, the fix in this commit is wrong: the MODULE_DEVICE_TABLE(of,
....) is in the core part of the driver, not the I2C part. Therefore,
automatic module loading based on module.alias, based on matching with
the DT compatible string, loads the core part of the driver, but not
the I2C part. And threfore, the i2c_driver is not registered, and the
codec is not known to the system, nor matched with a DT node with the
corresponding compatible string.
In order to fix that, we move the MODULE_DEVICE_TABLE(of, ...) into
the I2C part of the driver. The cs42l51_of_match[] array is also moved
as well, as it is not possible to have this definition in one file,
and the MODULE_DEVICE_TABLE(of, ...) invocation in another file, due
to how MODULE_DEVICE_TABLE works.
Thanks to this commit, the I2C part of the driver now properly
autoloads, and thanks to its dependency on the core part, the core
part gets autoloaded as well, resulting in a functional sound card
without having to manually load kernel modules.
Fixes: 2cb1e0259f50 ("ASoC: cs42l51: re-hook of_match_table pointer") Cc: stable@vger.kernel.org Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Link: https://lore.kernel.org/r/20230713112112.778576-1-thomas.petazzoni@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:
BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
preempt_count: 10001, expected: 0
RCU nest depth: 0, expected: 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
---[ end trace ad1c64905aac14a6 ]-
The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().
Fix this by running IRQ handler, rt5640_irq(), in thread context.
Hence replace request_irq() calls with devm_request_threaded_irq().
Fixes: 051dade34695 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2") Cc: stable@vger.kernel.org Cc: Oder Chiou <oder_chiou@realtek.com> Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Byte mask for channel-1 of stream-1 is not getting enabled and this
causes failures during ADX use cases. This happens because the byte
map value 0 matches the byte map array and put() callback returns
without enabling the corresponding bits in the byte mask.
ADX supports 4 output streams and each stream can have a maximum of
16 channels. Each byte in the input frame is uniquely mapped to a
byte in one of these 4 outputs. This mapping is done with the help of
byte map array via user space control setting. The byte map array
size in the driver is 16 and each array element is of size 4 bytes.
This corresponds to 64 byte map values.
Each byte in the byte map array can have any value between 0 to 255
to enable the corresponding bits in the byte mask. The value 256 is
used as a way to disable the byte map. However the byte map array
element cannot store this value. The put() callback disables the byte
mask for 256 value and byte map value is reset to 0 for this case.
This causes problems during subsequent runs since put() callback,
for value of 0, just returns without enabling the byte mask. In short,
the problem is coming because 0 and 256 control values are stored as
0 in the byte map array.
Right now fix the put() callback by actually looking at the byte mask
array state to identify if any change is needed and update the fields
accordingly. The get() callback needs an update as well to return the
correct control value that user has set before. Note that when user
set 256, the value is stored as 0 and byte mask is disabled. So byte
mask state is used to either return 256 or the value from byte map
array.
Given above, this looks bit complicated and all this happens because
the byte map array is tightly packed and cannot actually store the 256
value. Right now the priority is to fix the existing failure and a TODO
item is put to improve this logic.
Fixes: 3c97881b8c8a ("ASoC: tegra: Fix kcontrol put callback in ADX") Cc: stable@vger.kernel.org Signed-off-by: Sheetal <sheetal@nvidia.com> Reviewed-by: Mohan Kumar D <mkumard@nvidia.com> Reviewed-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1688015537-31682-3-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas reports that on an i.MX8MP-based system where MCLK needs to be
used as an input, the MCLK pin is actually an output, despite not having
the 'fsl,sai-mclk-direction-output' property present in the devicetree.
This is caused by commit ff87d619ac18 ("ASoC: fsl_sai: Enable
MCTL_MCLK_EN bit for master mode") that sets FSL_SAI_MCTL_MCLK_EN
unconditionally for imx8mm/8mn/8mp/93, causing the MCLK to always
be configured as output.
FSL_SAI_MCTL_MCLK_EN corresponds to the MOE (MCLK Output Enable) bit
of register MCR and the drivers sets it when the
'fsl,sai-mclk-direction-output' devicetree property is present.
Revert the commit to allow SAI to use MCLK as input as well.
Cc: stable@vger.kernel.org Fixes: ff87d619ac18 ("ASoC: fsl_sai: Enable MCTL_MCLK_EN bit for master mode") Reported-by: Andreas Henriksson <andreas@fatal.se> Signed-off-by: Fabio Estevam <festevam@denx.de> Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com> Link: https://lore.kernel.org/r/20230706221827.1938990-1-festevam@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why & How]
Port of a change that went into DCN314 to keep the PHY enabled
when we have a connected and active DP display.
The PHY can hang if PHY refclk is disabled inadvertently.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Josip Pavic <josip.pavic@amd.com> Acked-by: Alan Liu <haoping.liu@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why & How]
If there is no TG allocation we can dereference a NULL pointer when
checking if the TG is enabled.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alan Liu <haoping.liu@amd.com> Signed-off-by: Taimur Hassan <syed.hassan@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
All of pipes will be used when the MPC split enable on the dcn
which just has 2 pipes. Then MPO enter will trigger the minimal
transition which need programe dcn from 2 pipes MPC split to 2
pipes MPO. This action will cause lag if happen frequently.
[HOW]
Disable the MPC split for the platform which dcn resource is limited
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Alvin Lee <alvin.lee2@amd.com> Acked-by: Alan Liu <haoping.liu@amd.com> Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up until now, amdgpu was silently degrading to vsync when
user-space requested an async flip but the hardware didn't support
it.
The hardware doesn't support immediate flips when the update changes
the FB pitch, the DCC state, the rotation, enables or disables CRTCs
or planes, etc. This is reflected in the dm_crtc_state.update_type
field: UPDATE_TYPE_FAST means that immediate flip is supported.
Silently degrading async flips to vsync is not the expected behavior
from a uAPI point-of-view. Xorg expects async flips to fail if
unsupported, to be able to fall back to a blit. i915 already behaves
this way.
This patch aligns amdgpu with uAPI expectations and returns a failure
when an async flip is not possible.
Signed-off-by: Simon Ser <contact@emersion.fr> Reviewed-by: André Almeida <andrealmeid@igalia.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: André Almeida <andrealmeid@igalia.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dmt_mode is allocated and never freed in this function.
It was found with the ast driver, but most drivers using generic fbdev
setup are probably affected.
In below thousands of screen rotation loop tests with virtual display
enabled, a CPU hard lockup issue may happen, leading system to unresponsive
and crash.
do {
xrandr --output Virtual --rotate inverted
xrandr --output Virtual --rotate right
xrandr --output Virtual --rotate left
xrandr --output Virtual --rotate normal
} while (1);
NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
So CPU1 stucks in hrtimer_cancel as timer callback is running endless on
current clock base, as that timer queue on CPU2 has no chance to finish it
because of failing to hold the lock. So NMI watchdog will throw the errors
after its threshold, and all later CPUs are impacted/blocked.
So use hrtimer_try_to_cancel to fix this, as disable_vblank callback
does not need to wait the handler to finish. And also it's not necessary
to check the return value of hrtimer_try_to_cancel, because even if it's
-1 which means current timer callback is running, it will be reprogrammed
in hrtimer_start with calling enable_vblank to make it works.
v2: only re-arm timer when vblank is enabled (Christian) and add a Fixes
tag as well
v3: drop warn printing (Christian)
v4: drop superfluous check of blank->enabled in timer function, as it's
guaranteed in drm_handle_vblank (Christian)
Fixes: 84ec374bd580 ("drm/amdgpu: create amdgpu_vkms (v4)") Cc: stable@vger.kernel.org Suggested-by: Christian König <christian.koenig@amd.com> Signed-off-by: Guchun Chen <guchun.chen@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently dma_resv_get_fences() will leak the previously
allocated array if the fence iteration got restarted and
the krealloc_array() fails.
Free the old array by hand, and make sure we still clear
the returned *fences so the caller won't end up accessing
freed memory. Some (but not all) of the callers of
dma_resv_get_fences() seem to still trawl through the
array even when dma_resv_get_fences() failed. And let's
zero out *num_fences as well for good measure.
Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Christian König <christian.koenig@amd.com> Cc: linux-media@vger.kernel.org Cc: dri-devel@lists.freedesktop.org Cc: linaro-mm-sig@lists.linaro.org Fixes: d3c80698c9f5 ("dma-buf: use new iterator in dma_resv_get_fences v3") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20230713194745.1751-1-ville.syrjala@linux.intel.com Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When looking at the TC selftest reports, I noticed one test was failing
because /proc/net/nf_conntrack was not available.
not ok 373 3992 - Add ct action triggering DNAT tuple conflict
Could not match regex pattern. Verify command output:
cat: /proc/net/nf_conntrack: No such file or directory
It is only available if NF_CONNTRACK_PROCFS kconfig is set. So the issue
can be fixed simply by adding it to the list of required kconfig.
The gs_usb driver handles USB devices with more than 1 CAN channel.
The RX path for all channels share the same bulk endpoint (the
transmitted bulk data encodes the channel number). These per-device
resources are allocated and submitted by the first opened channel.
During this allocation, the resources are either released immediately
in case of a failure or the URBs are anchored. All anchored URBs are
finally killed with gs_usb_disconnect().
Currently, gs_can_open() returns with an error if the allocation of a
URB or a buffer fails. However, if usb_submit_urb() fails, the driver
continues with the URBs submitted so far, even if no URBs were
successfully submitted.
Treat every error as fatal and free all allocated resources
immediately.
Switch to goto-style error handling, to prepare the driver for more
per-device resource allocation.
The mcp251xfd controller needs an idle bus to enter 'Normal CAN 2.0
mode' or . The maximum length of a CAN frame is 736 bits (64 data
bytes, CAN-FD, EFF mode, worst case bit stuffing and interframe
spacing). For low bit rates like 10 kbit/s the arbitrarily chosen
MCP251XFD_POLL_TIMEOUT_US of 1 ms is too small.
Otherwise during polling for the CAN controller to enter 'Normal CAN
2.0 mode' the timeout limit is exceeded and the configuration fails
with:
| $ ip link set dev can1 up type can bitrate 10000
| [ 731.911072] mcp251xfd spi2.1 can1: Controller failed to enter mode CAN 2.0 Mode (6) and stays in Configuration Mode (4) (con=0x068b0760, osc=0x00000468).
| [ 731.927192] mcp251xfd spi2.1 can1: CRC read error at address 0x0e0c (length=4, data=00 00 00 00, CRC=0x0000) retrying.
| [ 731.938101] A link change request failed with some changes committed already. Interface can1 may have been left with an inconsistent configuration, please check.
| RTNETLINK answers: Connection timed out
Make MCP251XFD_POLL_TIMEOUT_US timeout calculation dynamic. Use
maximum of 1ms and bit time of 1 full 64 data bytes CAN-FD frame in
EFF mode, worst case bit stuffing and interframe spacing at the
current bit rate.
For easier backporting define the macro MCP251XFD_FRAME_LEN_MAX_BITS
that holds the max frame length in bits, which is 736. This can be
replaced by can_frame_bits(true, true, true, true, CANFD_MAX_DLEN) in
a cleanup patch later.
Fixes: 55e5b97f003e8 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Signed-off-by: Fedor Ross <fedor.ross@ifm.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20230717-mcp251xfd-fix-increase-poll-timeout-v5-1-06600f34c684@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we reconfigure the SVE vector length we discard the backing storage
for the SVE vectors and then reallocate on next SVE use, leaving the SME
specific state alone. This means that we do not enable SME traps if they
were already disabled. That means that userspace code can enter streaming
mode without trapping, putting the task in a state where if we try to save
the state of the task we will fault.
Since the ABI does not specify that changing the SVE vector length disturbs
SME state, and since SVE code may not be aware of SME code in the process,
we shouldn't simply discard any ZA state. Instead immediately reallocate
the storage for SVE, and disable SME if we change the SVE vector length
while there is no SME state active.
Disabling SME traps on SVE vector length changes would make the overall
code more complex since we would have a state where we have valid SME state
stored but might get a SME trap.
Fixes: 9e4ab6c89109 ("arm64/sme: Implement vector length configuration prctl()s") Reported-by: David Spickett <David.Spickett@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230720-arm64-fix-sve-sme-vl-change-v2-1-8eea06b82d57@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMBus I2C buses have limits on the size of transfers they can do but
do not factor in the register length meaning we may try to do a transfer
longer than our length limit, the core will not take care of this.
Future changes will factor this out into the core but there are a number
of users that assume current behaviour so let's just do something
conservative here.
This does not take account padding bits but practically speaking these
are very rarely if ever used on I2C buses given that they generally run
slowly enough to mean there's no issue.
Since commit 241d2fb56a18 ("of: Make OF framebuffer device names unique"),
as spotted by Frédéric Bonnard, the historical "of-display" device is
gone: the updated logic creates "of-display.0" instead, then as many
"of-display.N" as required.
This means that offb no longer finds the expected device, which prevents
the Debian Installer from setting up its interface, at least on ppc64el.
Fix this by keeping "of-display" for the first device and "of-display.N"
for subsequent devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217328 Link: https://bugs.debian.org/1033058 Fixes: 241d2fb56a18 ("of: Make OF framebuffer device names unique") Cc: stable@vger.kernel.org Cc: Cyril Brulebois <cyril@debamax.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Helge Deller <deller@gmx.de> Acked-by: Helge Deller <deller@gmx.de> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Michal Suchánek <msuchanek@suse.de> Link: https://lore.kernel.org/r/20230710174007.2291013-1-robh@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When problems were noticed with the register address not being taken
into account when limiting raw transfers with I2C devices we fixed this
in the core. Unfortunately it has subsequently been realised that a lot
of buses were relying on the prior behaviour, partly due to unclear
documentation not making it obvious what was intended in the core. This
is all more involved to fix than is sensible for a fix commit so let's
just drop the original fixes, a separate commit will fix the originally
observed problem in an I2C specific way
Fixes: 3981514180c9 ("regmap: Account for register length when chunking") Fixes: c8e796895e23 ("regmap: spi-avmm: Fix regmap_bus max_raw_write") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Xu Yilun <yilun.xu@intel.com> Cc: stable@kernel.org Link: https://lore.kernel.org/r/20230712-regmap-max-transfer-v1-1-80e2aed22e83@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When looking for something else in LKFT reports [1], I noticed most of
the tests were skipped because the "teardown stage" did not complete
successfully.
Pedro found out this is due to the fact CONFIG_NF_FLOW_TABLE is required
but not listed in the 'config' file. Adding it to the list fixes the
issues on LKFT side. CONFIG_NET_ACT_CT is now set to 'm' in the final
kconfig.
When looking for something else in LKFT reports [1], I noticed that the
TC selftest ended with a timeout error:
not ok 1 selftests: tc-testing: tdc.sh # TIMEOUT 45 seconds
The timeout had been introduced 3 years ago, see the Fixes commit below.
This timeout is only in place when executing the selftests via the
kselftests runner scripts. I guess this is not what most TC devs are
using and nobody noticed the issue before.
The new timeout is set to 15 minutes as suggested by Pedro [2]. It looks
like it is plenty more time than what it takes in "normal" conditions.
The reproducer is running a balance and a cancel or pause in parallel.
The way balance finishes is a bit wonky, if we were paused we need to
save the balance_ctl in the fs_info, but clear it otherwise and cleanup.
However we rely on the return values being specific errors, or having a
cancel request or no pause request. If balance completes and returns 0,
but we have a pause or cancel request we won't do the appropriate
cleanup, and then the next time we try to start a balance we'll trip
this ASSERT.
The error handling is just wrong here, we always want to clean up,
unless we got -ECANCELLED and we set the appropriate pause flag in the
exclusive op. With this patch the reproducer ran for an hour without
tripping, previously it would trip in less than a few minutes.
Reported-by: syzbot+c0f3acf145cb465426d5@syzkaller.appspotmail.com CC: stable@vger.kernel.org # 6.1+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log