In an incredibly strange API design decision, qdisc->destroy() gets
called even if qdisc->init() never succeeded, not exclusively since
commit 28eb97a9988e ("net_sched: fix error recovery at qdisc creation"),
but apparently also earlier (in the case of qdisc_create_dflt()).
The taprio qdisc does not fully acknowledge this when it attempts full
offload, because it starts off with q->flags = TAPRIO_FLAGS_INVALID in
taprio_init(), then it replaces q->flags with TCA_TAPRIO_ATTR_FLAGS
parsed from netlink (in taprio_change(), tail called from taprio_init()).
But in taprio_destroy(), we call taprio_disable_offload(), and this
determines what to do based on FULL_OFFLOAD_IS_ENABLED(q->flags).
But looking at the implementation of FULL_OFFLOAD_IS_ENABLED()
(a bitwise check of bit 1 in q->flags), it is invalid to call this macro
on q->flags when it contains TAPRIO_FLAGS_INVALID, because that is set
to U32_MAX, and therefore FULL_OFFLOAD_IS_ENABLED() will return true on
an invalid set of flags.
As a result, it is possible to crash the kernel if user space forces an
error between setting q->flags = TAPRIO_FLAGS_INVALID, and the calling
of taprio_enable_offload(). This is because drivers do not expect the
offload to be disabled when it was never enabled.
The error that we force here is to attach taprio as a non-root qdisc,
but instead as child of an mqprio root qdisc:
Fixes: f1cce8ec8ee2 ("taprio: Add support for hardware offloading") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In of_mdiobus_register(), we should call of_node_put() for 'child'
escaped out of for_each_available_child_of_node().
Fixes: 92ebcf68e262 ("of_mdio: Fix broken PHY IRQ in case of probe deferral") Co-developed-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220913125659.3331969-1-windhl@126.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While converting max_tx_rate from bytes to Mbps, this value was set to 0,
if the original value was lower than 125000 bytes (1 Mbps). This would
cause no transmission rate limiting to occur. This happened due to lack of
check of max_tx_rate against the 1 Mbps value for max_tx_rate and the
following division by 125000. Fix this issue by adding a helper
i40e_bw_bytes_to_mbits() which sets max_tx_rate to minimum usable value of
50 Mbps, if its value is less than 1 Mbps, otherwise do the required
conversion by dividing by 125000.
Max MTU sent to VF is set to 0 during memory allocation. It cause
that max MTU on VF is changed to IAVF_MAX_RXBUFFER and does not
depend on data from HW.
Set max_mtu field in virtchnl_vf_resource struct to inform
VF in GET_VF_RESOURCES msg what size should be max frame.
Fixes: bf62fd247ce2 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx") Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After setting port VLAN and MTU to 9000 on VF with ice driver there
was an iavf error
"PF returned error -5 (IAVF_ERR_PARAM) to our request 6".
During queue configuration, VF's max packet size was set to
IAVF_MAX_RXBUFFER but on ice max frame size was smaller by VLAN_HLEN
due to making some space for port VLAN as VF is not aware whether it's
in a port VLAN. This mismatch in sizes caused ice to reject queue
configuration with ERR_PARAM error. Proper max_mtu is sent from ice PF
to VF with GET_VF_RESOURCES msg but VF does not look at this.
In iavf change max_frame from IAVF_MAX_RXBUFFER to max_mtu
received from pf with GET_VF_RESOURCES msg to make vf's
max_frame_size dependent from pf. Add check if received max_mtu is
not in eligible range then set it to IAVF_MAX_RXBUFFER.
Fixes: bf62fd247ce2 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx") Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix bad page state, free inappropriate page in handling dummy
descriptor. iavf_build_skb now has to check not only if rx_buffer is
NULL but also if size is zero, same thing in iavf_clean_rx_irq.
Without this patch driver would free page that will be used
by napi_build_skb.
Fixes: 6f66aea6da3e ("iavf: Fix handling of dummy receive descriptors") Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9a2f8811be41 ("net: stmmac: implement support for passive mode
converters via dt") has changed the plat->interface field semantics from
containing the PHY-mode to specifying the MAC-PCS interface mode. Due to
that the loongson32 platform code will leave the phylink interface
uninitialized with the PHY-mode intended by the means of the actual
platform setup. The commit-author most likely has just missed the
arch-specific code to fix. Let's mend the Loongson32 platform code then by
assigning the PHY-mode to the phy_interface field of the STMMAC platform
data.
Fixes: 9a2f8811be41 ("net: stmmac: implement support for passive mode converters via dt") Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com> Tested-by: Keguang Zhang <keguang.zhang@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Netdev drivers are expected to call dev_{uc,mc}_sync() in their
ndo_set_rx_mode method and dev_{uc,mc}_unsync() in their ndo_stop method.
This is mentioned in the kerneldoc for those dev_* functions.
The team driver calls dev_{uc,mc}_unsync() during ndo_uninit instead of
ndo_stop. This is ineffective because address lists (dev->{uc,mc}) have
already been emptied in unregister_netdevice_many() before ndo_uninit is
called. This mistake can result in addresses being leftover on former team
ports after a team device has been deleted; see test_LAG_cleanup() in the
last patch in this series.
Add unsync calls at their expected location, team_close().
v3:
* When adding or deleting a port, only sync/unsync addresses if the team
device is up. In other cases, it is taken care of at the right time by
ndo_open/ndo_set_rx_mode/ndo_stop.
Fixes: 88d4fc0ae093 ("net: introduce ethernet teaming device") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an AF_PACKET socket is used to send packets through ipvlan and the
default xmit function of the AF_PACKET socket is changed from
dev_queue_xmit() to packet_direct_xmit() via setsockopt() with the option
name of PACKET_QDISC_BYPASS, the skb->mac_header may not be reset and
remains as the initial value of 65535, this may trigger slab-out-of-bounds
bugs as following:
=================================================================
UG: KASAN: slab-out-of-bounds in ipvlan_xmit_mode_l2+0xdb/0x330 [ipvlan]
PU: 2 PID: 1768 Comm: raw_send Kdump: loaded Not tainted 6.0.0-rc4+ #6
ardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33
all Trace:
print_address_description.constprop.0+0x1d/0x160
print_report.cold+0x4f/0x112
kasan_report+0xa3/0x130
ipvlan_xmit_mode_l2+0xdb/0x330 [ipvlan]
ipvlan_start_xmit+0x29/0xa0 [ipvlan]
__dev_direct_xmit+0x2e2/0x380
packet_direct_xmit+0x22/0x60
packet_snd+0x7c9/0xc40
sock_sendmsg+0x9a/0xa0
__sys_sendto+0x18a/0x230
__x64_sys_sendto+0x74/0x90
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root cause is:
1. packet_snd() only reset skb->mac_header when sock->type is SOCK_RAW
and skb->protocol is not specified as in packet_parse_headers()
2. packet_direct_xmit() doesn't reset skb->mac_header as dev_queue_xmit()
In this case, skb->mac_header is 65535 when ipvlan_xmit_mode_l2() is
called. So when ipvlan_xmit_mode_l2() gets mac header with eth_hdr() which
use "skb->head + skb->mac_header", out-of-bound access occurs.
This patch replaces eth_hdr() with skb_eth_hdr() in ipvlan_xmit_mode_l2()
and reset mac header in multicast to solve this out-of-bound bug.
Fixes: a346ddd1a0fb ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Lu Wei <luwei32@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The underlying hardware may or may not allow reading of the head or tail
registers and it really makes no difference if we use the software
cached values. So, always used the software cached values.
Fixes: 979190eb004c ("i40e: Detection and recovery of TX queue hung logic moved to service_task from tx_timeout") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Co-developed-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
nf_osf_find() incorrectly returns true on mismatch, this leads to
copying uninitialized memory area in nft_osf which can be used to leak
stale kernel stack data to userspace.
CTCP messages should only be at the start of an IRC message, not
anywhere within it.
While the helper only decodes packes in the ORIGINAL direction, its
possible to make a client send a CTCP message back by empedding one into
a PING request. As-is, thats enough to make the helper believe that it
saw a CTCP message.
ct_sip_next_header and ct_sip_get_header return an absolute
value of matchoff, not a shift from current dataoff.
So dataoff should be assigned matchoff, not incremented by it.
This issue can be seen in the scenario when there are multiple
Contact headers and the first one is using a hostname and other headers
use IP addresses. In this case, ct_sip_walk_headers will work as follows:
The first ct_sip_get_header call to will find the first Contact header
but will return -1 as the header uses a hostname. But matchoff will
be changed to the offset of this header. After that, dataoff should be
set to matchoff, so that the next ct_sip_get_header call find the next
Contact header. But instead of assigning dataoff to matchoff, it is
incremented by it, which is not correct, as matchoff is an absolute
value of the offset. So on the next call to the ct_sip_get_header,
dataoff will be incorrect, and the next Contact header may not be
found at all.
We've found the AUX channel to be less reliable with PCLK_EDP at a
higher rate (typically 25 MHz). This is especially important on systems
with PSR-enabled panels (like Gru-Kevin), since we make heavy, constant
use of AUX.
According to Rockchip, using any rate other than 24 MHz can cause
"problems between syncing the PHY an PCLK", which leads to all sorts of
unreliabilities around register operations.
Fixes: 460ce76d7fb7 ("arm64: dts: rockchip: move core edp from rk3399-kevin to shared chromebook") Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: zain wang <wzz@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Link: https://lore.kernel.org/r/20220830131212.v2.1.I98d30623f13b785ca77094d0c0fd4339550553b6@changeid Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Gru-Bob board does not have a pull-up resistor on its
WLAN_HOST_WAKE# pin, but Kevin does. The production/vendor kernel
specified the pin configuration correctly as a pull-up, but this didn't
get ported correctly to upstream.
This means Bob's WLAN_HOST_WAKE# pin is floating, causing inconsistent
wakeup behavior.
Note that bt_host_wake_l has a similar dynamic, but apparently the
upstream choice was to redundantly configure both internal and external
pull-up on Kevin (see the "Kevin has an external pull up" comment in
rk3399-gru.dtsi). This doesn't cause any functional problem, although
it's perhaps wasteful.
In create_unique_id(), kmalloc(, GFP_KERNEL) can fail due to
out-of-memory, if it fails, return errno correctly rather than
triggering panic via BUG_ON();
We currently check the MokSBState variable to decide whether we should
treat UEFI secure boot as being disabled, even if the firmware thinks
otherwise. This is used by shim to indicate that it is not checking
signatures on boot images. In the kernel, we use this to relax lockdown
policies.
However, in cases where shim is not even being used, we don't want this
variable to interfere with lockdown, given that the variable may be
non-volatile and therefore persist across a reboot. This means setting
it once will persistently disable lockdown checks on a given system.
So switch to the mirrored version of this variable, called MokSBStateRT,
which is supposed to be volatile, and this is something we can check.
Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Peter Jones <pjones@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just as with the 5570 (and the other Dell laptops), this enables the two
subwoofer speakers on the Dell Precision 5530 together with the main
ones, significantly increasing the audio quality. I've tested this
myself on a 5530 and can confirm it's working as expected.
The ASUS G15 2022 (GA503R) series laptop has the same node-to-DAC pairs
as early models and the G14, this includes bass speakers which are by
default mapped incorrectly to the 0x06 node.
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
For ARM processor, unaligned access to device memory is not allowed.
Method memcpy does not take care of alignment.
USB detection failure with the unaligned address of memory access, with
below kernel crash. To fix the unaligned address the kernel panic issue,
replace memcpy with memcpy_toio method.
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
Those two controllers both have problems with some USB3.0 devices,
particularly self-powered ones. Typical error messages include:
Timeout while waiting for setup device command
device not accepting address X, error -62
unable to enumerate USB device
By process of elimination the controllers themselves were identified as
the cause of the problem. Through trial and error the issue was solved
by using USB_QUIRK_RESET_RESUME for both chips.
Whenever the atmel_rs485_config() driver method would be called,
the USART mode is reset to normal mode before even checking if
RS485 flag is set, thus resulting in losing the previous USART
mode in the case where the checking fails.
Some tools, such as `linux-serial-test`, lead to the driver calling
this method when doing the setup of the serial port: after setting the
port mode (Hardware Flow Control, Normal Mode, RS485 Mode, etc.),
`linux-serial-test` tries to enable/disable RS485 depending on
the commandline arguments that were passed.
Example of how this issue could reveal itself:
When doing a serial communication with Hardware Flow Control through
`linux-serial-test`, the tool would lead to the driver roughly doing
the following:
- set the corresponding bit to 1 (ATMEL_US_USMODE_HWHS bit in the
ATMEL_US_MR register) through the atmel_set_termios() to enable
Hardware Flow Control
- disable RS485 through the atmel_config_rs485() method
Thus, when the latter is called, the mode will be reset and the
previously set bit is unset, leaving USART in normal mode instead of
the expected Hardware Flow Control mode.
This fix ensures that this reset is only done if the checking for
RS485 succeeds and that the previous mode is preserved otherwise.
Fixes: d8e74b6706884 ("ARM: 6092/1: atmel_serial: support for RS485 communications") Cc: stable <stable@kernel.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com> Link: https://lore.kernel.org/r/20220824142902.502596-1-sergiu.moga@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
At this moment, TXEMPTY is checked before sending data on RS485 and ISO7816
modes. However, TXEMPTY is risen when FIFO (if used) or the Transmit Shift
Register are empty, even though TXRDY might be up and controller is able to
receive data. Since the controller sends data only when TXEMPTY is ready,
on RS485, when DMA is not used, the RTS pin is driven low after each byte.
With this patch, the characters will be transmitted when TXRDY is up and
so, RTS pin will remain high between bytes.
The performance improvement on RS485 is about 8% with a baudrate of 300.
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
Currently xhci-mtk needs software-managed bandwidth allocation for
periodic endpoints, it allocates the microframe index for the first
start-split packet for each endpoint. As this index allocation logic
should avoid the conflicts with other full/low-speed periodic endpoints,
it uses the worst case byte budgets on high-speed bus bandwidth
For example, for an isochronos IN endpoint with 192 bytes budget,
it will consume the whole 4 u-frames(188 * 4) while the actual
full-speed bus budget should be just 192bytes.
This patch changes the low/full-speed bandwidth allocation logic
to use "approximate" best case budget for lower speed bandwidth
management. For the same endpoint from the above example, the
approximate best case budget is now reduced to (188 * 2) bytes.
Without this patch, many usb audio headsets with 3 interfaces
(audio input, audio output, and HID) cannot be configured
on xhci-mtk.
In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."
Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.
Tune the boundary for FS/LS ESIT due to CS:
For ISOC out-ep, the controller starts transfer data after
the first SS; for others, the data is already transferred
before the last CS.
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit c2252c6874d9 ("usb: dwc3: gadget: Prevent repeat pullup()")
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
It is recommended by the Synopsis databook to issue a DCTL.CSftReset
when reconnecting from a device-initiated disconnect routine. This
resolves issues with enumeration during fast composition switching
cases, which result in an unknown device on the host.
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
syzbot is hitting percpu_rwsem_assert_held(&cpu_hotplug_lock) warning at
cpuset_attach() [1], for commit baf59de3daebd355 ("cgroup: Fix
threadgroup_rwsem <-> cpus_read_lock() deadlock") missed that
cpuset_attach() is also called from cgroup_attach_task_all().
Add cpus_read_lock() like what cgroup_procs_write_start() does.
In pxa3xx_gcu_write, a count parameter of type size_t is passed to words of
type int. Then, copy_from_user() may cause a heap overflow because it is used
as the third argument of copy_from_user().
The L0 symbol exists in System.map, but not in .tmp_System.map. When
"cmp -s System.map .tmp_System.map" will show "Inconsistent kallsyms
data" error message in link-vmlinux.sh script.
When trying to get a file lock on an AFS file, the server may return
UAEAGAIN to indicate that the lock is already held. This is currently
translated by the default path to -EREMOTEIO.
Translate it instead to -EAGAIN so that we know we can retry it.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey E Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/166075761334.3533338.2591992675160918098.stgit@warthog.procyon.org.uk/ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
AZA HW may send a burst read/write request crossing 4K memory boundary.
The 4KB boundary is not guaranteed by Tegra HDA HW. Make SW change to
include the flag AZX_DCAPS_4K_BDLE_BOUNDARY to align BDLE to 4K
boundary.
It seems that the beep playback doesn't work well on IDT codec devices
when the codec auto-pm is enabled. Keep the power on while the beep
switch is enabled.
If the local processor work item for the rxrpc local endpoint gets requeued
by an event (such as an incoming packet) between it getting scheduled for
destruction and the UDP socket being closed, the rxrpc_local_destroyer()
function can get run twice. The second time it can hang because it can end
up waiting for cleanup events that will never happen.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pfuze_chip::regulator_descs is an array of size
PFUZE100_MAX_REGULATOR, the pfuze_chip::pfuze_regulators
is the pointer to the real regulators of a specific device.
The number of real regulator is supposed to be less than
the PFUZE100_MAX_REGULATOR, so we should use the size of
'regulator_num * sizeof(struct pfuze_regulator)' in memcpy().
This fixes the out of bounds access bug reported by KASAN.
The semaphore of nau8824 wasn't properly unlocked at some error
handling code paths, hence this may result in the unbalance (and
potential lock-up). Fix them to handle the semaphore up properly.
When doing a direct IO that spans the current EOF, and there are
written blocks beyond EOF that extend beyond the current write, the
only metadata update that needs to be done is a file size extension.
However, we don't mark such iomaps as IOMAP_F_DIRTY to indicate that
there is IO completion metadata updates required, and hence we may
fail to correctly sync file size extensions made in IO completion
when O_DSYNC writes are being used and the hardware supports FUA.
Hence when setting IOMAP_F_DIRTY, we need to also take into account
whether the iomap spans the current EOF. If it does, then we need to
mark it dirty so that IO completion will call generic_write_sync()
to flush the inode size update to stable storage correctly.
Fixes: 1271628828ea ("iomap: Use FUA for pure data O_DSYNC DIO writes") Signed-off-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: removed the ext4 part; they'll handle it separately] Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAINTAINERS: add Chandan as xfs maintainer for 5.4.y
This is an attempt to direct the bots and humans that are testing
LTS 5.4.y towards the maintainer of xfs in the 5.4.y tree.
Update Darrick's email address from upstream and add Chandan as xfs
maintaier for the 5.4.y tree.
Suggested-by: Darrick J. Wong <djwong@kernel.org> Link: https://lore.kernel.org/linux-xfs/Yrx6%2F0UmYyuBPjEr@magnolia/ Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stefan Metzmacher <metze@samba.org> Cc: stable@vger.kernel.org Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing direct writes we need to also invalidate the mapping in case
we have a cached copy of the affected page(s) in memory or else
subsequent reads of the data might return the old/stale content
before we wrote an update to the server.
Cc: stable@vger.kernel.org Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, The arguments passing to lockdep_hardirqs_{on,off} was fixed
in CALLER_ADDR0.
The function trace_hardirqs_on_caller should have been intended to use
caller_addr to represent the address that caller wants to be traced.
For example, lockdep log in riscv showing the last {enabled,disabled} at
__trace_hardirqs_{on,off} all the time(if called by):
[ 57.853175] hardirqs last enabled at (2519): __trace_hardirqs_on+0xc/0x14
[ 57.853848] hardirqs last disabled at (2520): __trace_hardirqs_off+0xc/0x14
After use trace_hardirqs_xx_caller, we can get more effective information:
[ 53.781428] hardirqs last enabled at (2595): restore_all+0xe/0x66
[ 53.782185] hardirqs last disabled at (2596): ret_from_exception+0xa/0x10
Link: https://lkml.kernel.org/r/20220901104515.135162-2-zouyipeng@huawei.com Cc: stable@vger.kernel.org Fixes: ae9dc543e63f8 ("tracing: Centralize preemptirq tracepoints and unify their usage") Signed-off-by: Yipeng Zou <zouyipeng@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a small race window at snd_pcm_oss_sync() that is called from
OSS PCM SNDCTL_DSP_SYNC ioctl; namely the function calls
snd_pcm_oss_make_ready() at first, then takes the params_lock mutex
for the rest. When the stream is set up again by another thread
between them, it leads to inconsistency, and may result in unexpected
results such as NULL dereference of OSS buffer as a fuzzer spotted
recently.
The fix is simply to cover snd_pcm_oss_make_ready() call into the same
params_lock mutex with snd_pcm_oss_make_ready_locked() variant.
VPP_WRAP_OSD1_MATRIX_COEF22.Coeff22 is documented as being bits 0-12,
not 16-28.
Without this the output tends to have a pink hue, changing it results
in better color accuracy.
The vendor kernel doesn't use this register. However the code which
sets VIU2_OSD1_MATRIX_COEF22 also uses bits 0-12. There is a slightly
different style of registers for configuring some of the other matrices,
which do use bits 16-28 for this coefficient, but those have names
ending in MATRIX_COEF22_30, and this is not one of those.
Commit edda97a9e5d2 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 175654c2348a ("powerpc: Add interrupt support to mpc8xxx_gpio").
Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:
[ 15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
[ 15.267168] lm90 0-004c: cannot request IRQ 49
[ 15.272708] lm90: probe of 0-004c failed with error -22
Fixes: 175654c2348a ("powerpc: Add interrupt support to mpc8xxx_gpio") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit e2d5a793ec6e ("drivers/of: Fix depth when unflattening devicetree")
forgot to fix up the depth check in the loop body in unflatten_dt_nodes()
which makes it possible to overflow the nps[] buffer...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
The soc/fsl/dpio driver will perform a soc_device_match()
to determine the optimal cache settings for a given CPU core.
If FSL_GUTS is not enabled, this search will fail and
the driver will not configure cache stashing for the given
DPIO, and a string of "unknown SoC" messages will appear:
fsl_mc_dpio dpio.7: unknown SoC version
fsl_mc_dpio dpio.6: unknown SoC version
fsl_mc_dpio dpio.5: unknown SoC version
Some RX errors, notably when disconnecting the cable, increase the RCSR
register. Once half full (0x7fff), an interrupt flood is generated. I
measured ~3k/s interrupts even after the RX errors transfer was
stopped.
Since we don't read and clear the RCSR register, we should disable this
interrupt.
Fixes: e8b8b88d5f4a ("net: phy: DP83822 initial driver submission") Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mm: Fix TLB flush for not-first PFNMAP mappings in unmap_region()
This is a stable-specific patch.
I botched the stable-specific rewrite of
commit f55f2908ef381 ("mmu_gather: Force tlb-flush VM_PFNMAP vmas"):
As Hugh pointed out, unmap_region() actually operates on a list of VMAs,
and the variable "vma" merely points to the first VMA in that list.
So if we want to check whether any of the VMAs we're operating on is
PFNMAP or MIXEDMAP, we have to iterate through the list and check each VMA.
USB external storage device(0x0b05:1932), use gnome-disk-utility tools
to test usb write < 30MB/s.
if does not to load module of uas for this device, can increase the
write speed from 20MB/s to >40MB/s.
2 keymap fixes for the Acer Aspire One AOD270 and the same hardware
rebranded as Packard Bell Dot SC:
1. The F2 key is marked with a big '?' symbol on the Packard Bell Dot SC,
this sends WMID_HOTKEY_EVENTs with a scancode of 0x27 add a mapping
for this.
2. Scancode 0x61 is KEY_SWITCHVIDEOMODE. Usually this is a duplicate
input event with the "Video Bus" input device events. But on these devices
the "Video Bus" does not send events for this key. Map 0x61 to KEY_UNKNOWN
instead of using KE_IGNORE so that udev/hwdb can override it on these devs.
TCP_FIN_WAIT2 and TCP_LAST_ACK were not handled, the connection is closing
so we can ignore them and avoid printing the "unhandled state"
warning message.
[ 1298.852386] nvmet_tcp: queue 2 unhandled state 5
[ 1298.879112] nvmet_tcp: queue 7 unhandled state 5
[ 1298.884253] nvmet_tcp: queue 8 unhandled state 5
[ 1298.889475] nvmet_tcp: queue 9 unhandled state 5
v2: Do not call nvmet_tcp_schedule_release_queue(), just ignore
the fin_wait2 and last_ack states.
The MSI is probably raised by incoming packets, so power down the device
and disable bus mastering to stop the traffic, as user confirmed this
approach works.
In addition to that, be extra safe and cancel reset task if it's running.
There is a timing issue captured during ishtp client sending stress tests.
It was observed during stress tests that ISH firmware is getting out of
ordered messages. This is a rare scenario as the current set of ISH client
drivers don't send much data to firmware. But this may not be the case
going forward.
When message size is bigger than IPC MTU, ishtp splits the message into
fragments and uses serialized async method to send message fragments.
The call stack:
ishtp_cl_send_msg_ipc->ipc_tx_callback(first fregment)->
ishtp_send_msg(with callback)->write_ipc_to_queue->
write_ipc_from_queue->callback->ipc_tx_callback(next fregment)......
When an ipc write complete interrupt is received, driver also calls
write_ipc_from_queue->ipc_tx_callback in ISR to start sending of next fragment.
Through ipc_tx_callback uses spin_lock to protect message splitting, as the
serialized sending method will call back to ipc_tx_callback again, so it doesn't
put sending under spin_lock, it causes driver cannot guarantee all fragments
be sent in order.
Considering this scenario:
ipc_tx_callback just finished a fragment splitting, and not call ishtp_send_msg
yet, there is a write complete interrupt happens, then ISR->write_ipc_from_queue
->ipc_tx_callback->ishtp_send_msg->write_ipc_to_queue......
Because ISR has higher exec priority than normal thread, this causes the new
fragment be sent out before previous fragment. This disordered message causes
invalid message to firmware.
The solution is, to send fragments synchronously:
Use ishtp_write_message writing fragments into tx queue directly one by one,
instead of ishtp_send_msg only writing one fragment with completion callback.
As no completion callback be used, so change ipc_tx_callback to ipc_tx_send.
If the previous thing cat'ing $debugfs/rd left the FIFO full, then
subsequent open could deadlock in rd_write() (because open is blocked,
not giving a chance for read() to consume any data in the FIFO). Also
it is generally a good idea to clear out old data from the FIFO.
Cong Wang noticed that the previous fix for sch_sfb accessing the queued
skb after enqueueing it to a child qdisc was incomplete: the SFB enqueue
function was also calling qdisc_qstats_backlog_inc() after enqueue, which
reads the pkt len from the skb cb field. Fix this by also storing the skb
len, and using the stored value to increment the backlog after enqueueing.
Fixes: d7235a8ffcb9 ("sch_sfb: Don't assume the skb is still around after enqueueing to child") Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Acked-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20220905192137.965549-1-toke@toke.dk Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a bug reported and analyzed by Nagaraj Arankal, where the handling
of a spurious non-SACK RTO could cause a connection to fail to clear
retrans_stamp, causing a later RTO to very prematurely time out the
connection with ETIMEDOUT.
Here is the buggy scenario, expanding upon Nagaraj Arankal's excellent
report:
(*1) Send one data packet on a non-SACK connection
(*2) Because no ACK packet is received, the packet is retransmitted
and we enter CA_Loss; but this retransmission is spurious.
(*3) The ACK for the original data is received. The transmitted packet
is acknowledged. The TCP timestamp is before the retrans_stamp,
so tcp_may_undo() returns true, and tcp_try_undo_loss() returns
true without changing state to Open (because tcp_is_sack() is
false), and tcp_process_loss() returns without calling
tcp_try_undo_recovery(). Normally after undoing a CA_Loss
episode, tcp_fastretrans_alert() would see that the connection
has returned to CA_Open and fall through and call
tcp_try_to_open(), which would set retrans_stamp to 0. However,
for non-SACK connections we hold the connection in CA_Loss, so do
not fall through to call tcp_try_to_open() and do not set
retrans_stamp to 0. So retrans_stamp is (erroneously) still
non-zero.
At this point the first "retransmission event" has passed and
been recovered from. Any future retransmission is a completely
new "event". However, retrans_stamp is erroneously still
set. (And we are still in CA_Loss, which is correct.)
(*4) After 16 minutes (to correspond with tcp_retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and
(*4) and we disabled keep alives.
The socket's timeout SHOULD be calculated from this point in
time, but instead it's calculated from the prior "event" 16
minutes ago (step (*2)).
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT, prematurely, because retrans_stamp is (erroneously)
too far in the past (set at the time of (*2)).
This commit fixes this bug by ensuring that we reuse in
tcp_try_undo_loss() the same careful logic for non-SACK connections
that we have in tcp_try_undo_recovery(). To avoid duplicating logic,
we factor out that logic into a new
tcp_is_non_sack_preventing_reopen() helper and call that helper from
both undo functions.
We should also bail from the io_work loop when we set rd_enabled to true,
so we don't attempt to read data from the socket when the TCP stream is
already out-of-sync or corrupted.
Fixes: 1cd562a5d941 ("nvme-tcp: add NVMe over TCP host driver") Reported-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When accessing Ports Performance Counters Register (PPCNT),
local port must be one if it is Function-Per-Port HCA that
HCA_CAP.num_ports is 1.
The offending patch can change the local port to other values
when accessing PPCNT after enabling switchdev mode. The following
syndrome will be printed:
# cat /sys/class/infiniband/rdmap4s0f0/ports/2/counters/*
# dmesg
mlx5_core 0000:04:00.0: mlx5_cmd_check:756:(pid 12450): ACCESS_REG(0x805) op_mod(0x1) failed, status bad parameter(0x3), syndrome (0x1e5585)
Fix it by setting local port to one for Function-Per-Port HCA.
projects / kernel.git / log