If ext4_fill_super detects an invalid number of inodes per group, the
resulting error message printed the number of blocks per group, rather
than the number of inodes per group. Fix it to print the correct value.
ext4_fill_super doublechecks the number of groups before mounting; if
that check fails, the resulting error message prints the group count
from the ext4_sb_info sbi, which hasn't been set yet. Print the freshly
computed group count instead (which at that point has just been computed
in "blocks_count").
A testing message was brought by c741018fdd8d ("net/bpfilter: fix dprintf
usage for /dev/kmsg") but should've been deleted before patch submission.
Although it doesn't cause any harm to the code or functionality itself, it's
totally unpleasant to have it displayed on every loop iteration with no real
use case. Thus remove it unconditionally.
Fixes: c741018fdd8d ("net/bpfilter: fix dprintf usage for /dev/kmsg") Signed-off-by: Bruno Meneguele <bmeneg@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver allows pwms to be requested as gpios via gpiolib. Obviously,
it should not be allowed to request a GPIO when its corresponding PWM is
already requested (and vice versa). So it requires some exclusion code.
Given that the PWMm and GPIO cores are not synchronized with respect to
each other, this exclusion code will also require proper
synchronization.
Such a mechanism was in place, but was inadvertently removed by Uwe's
clean-up in commit 8a111549e4ea ("pwm: Clear chip_data in pwm_put()").
Upon revisiting the synchronization mechanism, we found that
theoretically, it could allow two threads to successfully request
conflicting PWMs/GPIOs.
Replace with a bitmap which tracks PWMs in-use, plus a mutex. As long as
PWM and GPIO's respective request/free functions modify the in-use
bitmap while holding the mutex, proper synchronization will be
guaranteed.
Reported-by: YueHaibing <yuehaibing@huawei.com> Fixes: 8a111549e4ea ("pwm: Clear chip_data in pwm_put()") Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: YueHaibing <yuehaibing@huawei.com> Link: https://lkml.org/lkml/2019/5/31/963 Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[cg: Tested on an i.MX6Q board with two NXP PCA9685 chips] Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com> # cg's rebase Link: https://lore.kernel.org/lkml/20200330160238.GD2817345@ulmo/ Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
But now for the recent perf, it can't report the branch type statistics.
It's a regression issue caused by commit 2a1a87ebdc76 ("perf report: Fix
a no annotate browser displayed issue"), which only counts the branch
type statistics for browser mode.
This patch moves the branch_type_count() outside of ui__has_annotation()
checking, then branch type statistics can work for stdio mode.
Fixes: 2a1a87ebdc76 ("perf report: Fix a no annotate browser displayed issue") Signed-off-by: Jin Yao <yao.jin@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20200313134607.12873-1-yao.jin@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'func' variable can come from the user in the __nd_ioctl(). If it's
too high then the (1 << func) shift in acpi_nfit_clear_to_send() is
undefined. In acpi_nfit_ctl() we pass 'func' to test_bit(func, &dsm_mask)
which could result in an out of bounds access.
To fix these issues, I introduced the NVDIMM_CMD_MAX (31) define and
updated nfit_dsm_revid() to use that define as well instead of magic
numbers.
Fixes: 06d00394e94e ("acpi/nfit: Fix command-supported detection") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Link: https://lore.kernel.org/r/20200225161927.hvftuq7kjn547fyj@kili.mountain Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve comments in jbd2_journal_commit_transaction() to describe why
we don't need to clear the buffer_mapped bit for freeing file mapping
buffers whose page mapping is NULL.
Link: https://lore.kernel.org/r/20200217112706.20085-1-yi.zhang@huawei.com Fixes: d43a2419e505 ("jbd2: do not clear the BH_Mapped flag when forgetting a metadata buffer") Suggested-by: Jan Kara <jack@suse.cz> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Host event can be sent by remoteproc by any time, and
cros_ec_rpmsg_callback would be called after cros_ec_rpmsg_create_ept.
But the cros_ec_device is initialized after that, which cause host event
handler to use cros_ec_device that are not initialized properly yet.
Fix this by don't schedule host event handler before cros_ec_register
returns. Instead, remember that we have a pending host event, and
schedule host event handler after cros_ec_register.
Fixes: a58718d3d7b1 ("platform/chrome: cros_ec_rpmsg: Fix race with host command when probe failed.") Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The async version of ufshcd_hold(async == true), which is only called in
queuecommand path as for now, is expected to work in atomic context, thus
it should not sleep or schedule out. When it runs into the condition that
clocks are ON but link is still in hibern8 state, it should bail out
without flushing the clock ungate work.
Fixes: f3378aa1959e ("scsi: ufshcd: Fix race between clk scaling and ungate work") Link: https://lore.kernel.org/r/1581392451-28743-6-git-send-email-cang@codeaurora.org Reviewed-by: Hongwu Su <hongwus@codeaurora.org> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit efa45a58dc65 ("ovl: make i_ino consistent with st_ino in more
cases"), relaxed the condition nfs_export=on in order to set the value of
i_ino to xino map of real ino.
Specifically, it also relaxed the pre-condition that index=on for
consistent i_ino. This opened the corner case of lower hardlink in
ovl_get_inode(), which calls ovl_fill_inode() with ino=0 and then
ovl_init_inode() is called to set i_ino to lower real ino without the xino
mapping.
Pass the correct values of ino;fsid in this case to ovl_fill_inode(), so it
can initialize i_ino correctly.
Fixes: efa45a58dc65 ("ovl: make i_ino consistent with st_ino in more ...") Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael writes:
It has not been marked for -stable or otherwise requested to be
included AFAICS. Also it depends on other mainline commits that
have not been included into 5.6.5.
Reported-by: Toralf Förster <toralf.foerster@gmx.de> Reported-by: Rafael J. Wysocki <rafael@kernel.org> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b202c04f8d0dd17dde6763551632b5f1fb0d64b0 ("net: dsa:
configure the MTU for switch ports") my Lamobo R1 platform which uses
an allwinner,sun7i-a20-gmac compatible Ethernet MAC started to fail
by rejecting a MTU of 1536. The reason for that is that the DMA
capabilities are not readable on this version of the IP, and there
is also no 'tx-fifo-depth' property being provided in Device Tree. The
property is documented as optional, and is not provided.
Chen-Yu indicated that the FIFO sizes are 4KB for TX and 16KB for RX, so
provide these values through platform data as an immediate fix until
various Device Tree sources get updated accordingly.
Fixes: cd0801e3d55f ("net: stmmac: Do not accept invalid MTU values") Suggested-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cited patch missed to extract PCI pf number accurately for PF and VF
port flavour. It considered PCI device + function number.
Due to this, device having non zero device number shown large pfnum.
Hence, use only PCI function number; to avoid similar errors, derive
pfnum one time for all port flavours.
Current value of nest_level, assigned from net_device lower_level value,
does not reflect the actual number of vlan headers, needed to pop.
For ex., if we have untagged ingress traffic sended over vlan devices,
instead of one pop action, driver will perform two pop actions.
To fix that, calculate nest_level as difference between vlan device and
parent device lower_levels.
Fixes: a7983db5f52c ("net: remove unnecessary variables and callback") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Signed-off-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving mt7623 logic out off mt7530, is required to make hardware setting
consistent after we introduce phylink to mtk driver.
Fixes: fcc7dd9fe410 ("net: ethernet: mediatek: Add basic PHYLINK support") Reviewed-by: Sean Wang <sean.wang@mediatek.com> Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: René van Dorst <opensource@vdorst.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving mt7623 logic out off mt7530, is required to make hardware setting
consistent after we introduce phylink to mtk driver.
Fixes: 6ae43c9d6729 ("net: dsa: mt7530: Convert to PHYLINK API") Reviewed-by: Sean Wang <sean.wang@mediatek.com> Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: René van Dorst <opensource@vdorst.com> Tested-by: Frank Wunderlich <frank-w@public-files.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows netif_receive_generic_xdp() to correctly determine the RX
queue from which the skb is coming, so that the context passed to the
XDP program will contain the correct RX queue index.
Signed-off-by: Gilberto Bertin <me@jibi.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For HZ < 1000 timeout 2000us rounds up to 1 jiffy but expires randomly
because next timer interrupt could come shortly after starting softirq.
For commonly used CONFIG_HZ=1000 nothing changes.
Fixes: 1284c40c9b04 ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning") Reported-by: Dmitry Yakunin <zeil@yandex-team.ru> Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the local node id(qrtr_local_nid) is not modified after its
initialization, it equals to the broadcast node id(QRTR_NODE_BCAST).
So the messages from local node should not be taken as broadcast
and keep the process going to send them out anyway.
The definitions are as follow:
static unsigned int qrtr_local_nid = NUMA_NO_NODE;
Fixes: e0465a2b38a4 ("net: qrtr: Broadcast messages only from control port") Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KSZ9131 will not work with some switches due to workaround for KSZ9031
introduced in commit 74adacb23914c0c4ef6b497f3f9f1dda7e197d4b
("net/phy: micrel: Add workaround for bad autoneg").
Use genphy_read_status instead of dedicated ksz9031_read_status.
Fixes: 67b9850dd5a9 ("net: phy: micrel: add Microchip KSZ9131 initial driver") Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The behaviour for what is considered an anycast address changed in
commit 0c8dfdb319ff ("ipv6: Only create RTF_CACHE routes after
encountering pmtu exception"). This now considers the first
address in a subnet where there is a route via a gateway
to be an anycast address.
This breaks path MTU discovery and traceroutes when a host in a
remote network uses the address at the start of a prefix
(eg 2600:: advertised as 2600::/48 in the DFZ) as ICMP errors
will not be sent to anycast addresses.
This patch excludes any routes with a gateway, or via point to
point links, like the behaviour previously from
rt6_is_gw_or_nonexthop in net/ipv6/route.c.
This can be tested with:
ip link add v1 type veth peer name v2
ip netns add test
ip netns exec test ip link set lo up
ip link set v2 netns test
ip link set v1 up
ip netns exec test ip link set v2 up
ip addr add 2001:db8::1/64 dev v1 nodad
ip addr add 2001:db8:100:: dev lo nodad
ip netns exec test ip addr add 2001:db8::2/64 dev v2 nodad
ip netns exec test ip route add unreachable 2001:db8:1::1
ip netns exec test ip route add 2001:db8:100::/64 via 2001:db8::1
ip netns exec test sysctl net.ipv6.conf.all.forwarding=1
ip route add 2001:db8:1::1 via 2001:db8::2
ping -I 2001:db8::1 2001:db8:1::1 -c1
ping -I 2001:db8:100:: 2001:db8:1::1 -c1
ip addr delete 2001:db8:100:: dev lo
ip netns delete test
Currently the first ping will get back a destination unreachable ICMP
error, but the second will never get a response, with "icmp6_send:
acast source" logged. After this patch, both get destination
unreachable ICMP replies.
Fixes: 0c8dfdb319ff ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception") Signed-off-by: Tim Stallard <code@timstallard.me.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_IP_MULTICAST is not set and multicast ip is added to the device
with autojoin flag or when multicast ip is deleted kernel will crash.
steps to reproduce:
ip addr add 224.0.0.0/32 dev eth0
ip addr del 224.0.0.0/32 dev eth0
or
ip addr add 224.0.0.0/32 dev eth0 autojoin
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
pc : _raw_write_lock_irqsave+0x1e0/0x2ac
lr : lock_sock_nested+0x1c/0x60
Call trace:
_raw_write_lock_irqsave+0x1e0/0x2ac
lock_sock_nested+0x1c/0x60
ip_mc_config.isra.28+0x50/0xe0
inet_rtm_deladdr+0x1a8/0x1f0
rtnetlink_rcv_msg+0x120/0x350
netlink_rcv_skb+0x58/0x120
rtnetlink_rcv+0x14/0x20
netlink_unicast+0x1b8/0x270
netlink_sendmsg+0x1a0/0x3b0
____sys_sendmsg+0x248/0x290
___sys_sendmsg+0x80/0xc0
__sys_sendmsg+0x68/0xc0
__arm64_sys_sendmsg+0x20/0x30
el0_svc_common.constprop.2+0x88/0x150
do_el0_svc+0x20/0x80
el0_sync_handler+0x118/0x190
el0_sync+0x140/0x180
Fixes: 610e912110e5 ("multicast: Extend ip address command to enable multicast group join/leave on") Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu> Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN
Control register must be set to Consistent to let tagged frames pass
through as is, otherwise their tags will be stripped.
Fixes: 2d5d4391d6ef ("net: dsa: mediatek: add VLAN support for MT7530") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: René van Dorst <opensource@vdorst.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creation and management of L2TPv3 tunnels and session through netlink
requires CAP_NET_ADMIN. However, a process with CAP_NET_ADMIN in a
non-initial user namespace gets an EPERM due to the use of the
genetlink GENL_ADMIN_PERM flag. Thus, management of L2TP VPNs inside
an unprivileged container won't work.
We replaced the GENL_ADMIN_PERM by the GENL_UNS_ADMIN_PERM flag
similar to other network modules which also had this problem, e.g.,
openvswitch (commit 8924be6e5426 "openvswitch: allow management from
inside user namespaces") and nl80211 (commit 9b4fe9101e013 "nl80211:
Allow privileged operations from user namespaces").
I tested this in the container runtime trustm3 (trustm3.github.io)
and was able to create l2tp tunnels and sessions in unpriviliged
(user namespaced) containers using a private network namespace.
For other runtimes such as docker or lxc this should work, too.
Signed-off-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4
In the test commands, version 4 is invalid.
So, the command should be failed.
After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."
Fixes: 93e0e4a5d07a ("net/hsr: Added support for HSR v1") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses __napi_schedule_irqoff() which is fine as long as it is
invoked with disabled interrupts by everybody. Since the commit
mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq
context. This may lead to list corruption if another driver uses
__napi_schedule_irqoff() in IRQ context.
Use __napi_schedule() which safe to use from IRQ and softirq context.
Fixes: 89ea515977160 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compilation can fail due to having an inline function reference where the
function body is not present.
Fix by removing the inline tag.
Fixes: b13c81427de3 ("scsi: lpfc: Add registration for CPU Offline/Online events") Link: https://lore.kernel.org/r/20191111230401.12958-4-jsmart2021@gmail.com Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 68caebec3418 ("ASoC: stm32: sai: manage rebind issue")
converts some function calls to their non-devm equivalents. The
appropriate cleanup code was added to the remove function, but not
to the probe function. Add a call to snd_dmaengine_pcm_unregister
to compensate for the call to snd_dmaengine_pcm_register in case
of subsequent failure.
Fixes: commit 68caebec3418 ("ASoC: stm32: sai: manage rebind issue") Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Acked-by: Olivier Moysan <olivier.moysan@st.com> Link: https://lore.kernel.org/r/1586099028-5104-1-git-send-email-Julia.Lawall@inria.fr Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
efi_thunk_set_variable() treated the NULL "data" pointer as an invalid
parameter, and this broke the deletion of variables in mixed mode.
This commit fixes the check of data so that the userspace program can
delete a variable in mixed mode.
While the commit dc1d902fe38e ("mfd: dln2: More sanity checking for endpoints")
tries to harden the sanity checks it made at the same time a regression,
i.e. mixed in and out endpoints. Obviously it should have been not tested on
real hardware at that time, but unluckily it didn't happen.
So, fix above mentioned typo and make device being enumerated again.
While here, introduce an enumerator for magic values to prevent similar issue
to happen in the future.
Fixes: dc1d902fe38e ("mfd: dln2: More sanity checking for endpoints") Cc: Oliver Neukum <oneukum@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The BPF verifier tried to track values based on 32-bit comparisons by
(ab)using the tnum state via af33701ac784 ("bpf: Provide better register
bounds after jmp32 instructions"). The idea is that after a check like
this:
if ((u32)r0 > 3)
exit
We can't meaningfully constrain the arithmetic-range-based tracking, but
we can update the tnum state to (value=0,mask=0xffff'ffff'0000'0003).
However, the implementation from af33701ac784 didn't compute the tnum
constraint based on the fixed operand, but instead derives it from the
arithmetic-range-based tracking. This means that after the following
sequence of operations:
if (r0 >= 0x1'0000'0001)
exit
if ((u32)r0 > 7)
exit
The verifier assumed that the lower half of r0 is in the range (0, 0)
and apply the tnum constraint (value=0,mask=0xffff'ffff'0000'0000) thus
causing the overall tnum to be (value=0,mask=0x1'0000'0000), which was
incorrect. Provide a fixed implementation.
Fixes: af33701ac784 ("bpf: Provide better register bounds after jmp32 instructions") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/bpf/20200330160324.15259-3-daniel@iogearbox.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Refactor sdhci_set_timeout() such that platform drivers can do some
functionality in a set_timeout() callback and then call
__sdhci_set_timeout() to complete the operation.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20200116105154.7685-7-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The system will be hang up during S3 suspend because of SMU is pending
for GC not respose the register CP_HQD_ACTIVE access request.This issue
root cause of accessing the GC register under enter GFX CGGPG and can
be fixed by disable GFX CGPG before perform suspend.
v2: Use disable the GFX CGPG instead of RLC safe mode guard.
commit a1042ade48d6 ("drm/dp_mst: Remove VCPI while disabling topology
mgr")
Prompted me to take a closer look at how we clear the payload state in
general when disabling the topology, and it turns out there's actually
two subtle issues here.
The first is that we're not grabbing &mgr.payload_lock when clearing the
payloads in drm_dp_mst_topology_mgr_set_mst(). Seeing as the canonical
lock order is &mgr.payload_lock -> &mgr.lock (because we always want
&mgr.lock to be the inner-most lock so topology validation always
works), this makes perfect sense. It also means that -technically- there
could be racing between someone calling
drm_dp_mst_topology_mgr_set_mst() to disable the topology, along with a
modeset occurring that's modifying the payload state at the same time.
The second is the more obvious issue that Wayne Lin discovered, that
we're not clearing proposed_payloads when disabling the topology.
I actually can't see any obvious places where the racing caused by the
first issue would break something, and it could be that some of our
higher-level locks already prevent this by happenstance, but better safe
then sorry. So, let's make it so that drm_dp_mst_topology_mgr_set_mst()
first grabs &mgr.payload_lock followed by &mgr.lock so that we never
race when modifying the payload state. Then, we also clear
proposed_payloads to fix the original issue of enabling a new topology
with a dirty payload state. This doesn't clear any of the drm_dp_vcpi
structures, but those are getting destroyed along with the ports anyway.
Changes since v1:
* Use sizeof(mgr->payloads[0])/sizeof(mgr->proposed_vcpis[0]) instead -
vsyrjala
Cc: Sean Paul <sean@poorly.run> Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200122194321.14953-1-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The proper fix for this is probably cleanup the VCPI allocations when we're
enabling the topology, or on the first payload allocation. For now though,
let's just revert.
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: a1042ade48d6 ("drm/dp_mst: Remove VCPI while disabling topology mgr") Cc: Sean Paul <sean@poorly.run> Cc: Wayne Lin <Wayne.Lin@amd.com> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200117205149.97262-1-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When driver is set to enable bb credit recovery, the switch displayed the
setting as inactive. If the link bounces, it switches to Active.
During link up processing, the driver currently does a MBX_READ_SPARAM
followed by a MBX_CONFIG_LINK. These mbox commands are queued to be
executed, one at a time and the completion is processed by the worker
thread. Since the MBX_READ_SPARAM is done BEFORE the MBX_CONFIG_LINK, the
BB_SC_N bit is never set the the returned values. BB Credit recovery status
only gets set after the driver requests the feature in CONFIG_LINK, which
is done after the link up. Thus the ordering of READ_SPARAM needs to follow
the CONFIG_LINK.
Fix by reordering so that READ_SPARAM is done after CONFIG_LINK. Added a
HBA_DEFER_FLOGI flag so that any FLOGI handling waits until after the
READ_SPARAM is done so that the proper BB credit value is set in the FLOGI
payload.
Fixes: 6e714b344391 ("scsi: lpfc: Fix configuration of BB credit recovery in service parameters") Cc: <stable@vger.kernel.org> # v5.4+ Link: https://lore.kernel.org/r/20200128002312.16346-4-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver today is reading service parameters from the firmware and then
overwriting the firmware-provided values with values of its own. There are
some switch features that require preliminary FLOGI's that are
switch-specific and done prior to the actual fabric FLOGI for traffic. The
fw will perform those FLOGIs and will revise the service parameters for the
features configured. As the driver later overwrites those values with its
own values, it misconfigures things like BBSCN use by doing so.
Correct by eliminating the driver-overwrite of firmware values. The driver
correctly re-reads the service parameters after each link up to obtain the
latest values from firmware.
Link: https://lore.kernel.org/r/20191105005708.7399-3-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are reports of multiple ports on the same system displaying different
hostnames in fabric FDMI displays.
Currently, the driver registers the hostname at initialization and obtains
the hostname via init_utsname()->nodename queried at the time the FC link
comes up. Unfortunately, if the machine hostname is updated after
initialization, such as via DHCP or admin command, the value registered
initially will be incorrect.
Fix by having the driver save the hostname that was registered with FDMI.
The driver then runs a heartbeat action that will check the hostname. If
the name changes, reregister the FMDI data.
The hostname is used in RSNN_NN, FDMI RPA and FDMI RHBA.
Link: https://lore.kernel.org/r/20191218235808.31922-5-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The recent affinitization didn't address cpu offlining/onlining. If an
interrupt vector is shared and the low order cpu owning the vector is
offlined, as interrupts are managed, the vector is taken offline. This
causes the other CPUs sharing the vector will hang as they can't get io
completions.
Correct by registering callbacks with the system for Offline/Online
events. When a cpu is taken offline, its eq, which is tied to an interrupt
vector is found. If the cpu is the "owner" of the vector and if the
eq/vector is shared by other CPUs, the eq is placed into a polled mode.
Additionally, code paths that perform io submission on the "sharing CPUs"
will check the eq state and poll for completion after submission of new io
to a wq that uses the eq.
Similarly, when a cpu comes back online and owns an offlined vector, the eq
is taken out of polled mode and rearmed to start driving interrupts for eq.
Link: https://lore.kernel.org/r/20191105005708.7399-9-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a bug in the way dm-clone handles discards, which can lead to
discarding the wrong blocks or trying to discard blocks beyond the end
of the device.
This could lead to data corruption, if the destination device indeed
discards the underlying blocks, i.e., if the discard operation results
in the original contents of a block to be lost.
The root of the problem is the code that calculates the range of regions
covered by a discard request and decides which regions to discard.
Since dm-clone handles the device in units of regions, we don't discard
parts of a region, only whole regions.
The range is calculated as:
rs = dm_sector_div_up(bio->bi_iter.bi_sector, clone->region_size);
re = bio_end_sector(bio) >> clone->region_shift;
, where 'rs' is the first region to discard and (re - rs) is the number
of regions to discard.
The bug manifests when we try to discard part of a single region, i.e.,
when we try to discard a block with size < region_size, and the discard
request both starts at an offset with respect to the beginning of that
region and ends before the end of the region.
The root cause is the following comparison:
if (rs == re)
// skip discard and complete original bio immediately
, which doesn't take into account that 'rs' might be greater than 're'.
Thus, we then issue a discard request for the wrong blocks, instead of
skipping the discard all together.
Fix the check to also take into account the above case, so we don't end
up discarding the wrong blocks.
Also, add some range checks to dm_clone_set_region_hydrated() and
dm_clone_cond_set_range(), which update dm-clone's region bitmap.
Note that the aforementioned bug doesn't cause invalid memory accesses,
because dm_clone_is_range_hydrated() returns True for this case, so the
checks are just precautionary.
If we are in a place where it is known that interrupts are enabled,
functions spin_lock_irq/spin_unlock_irq should be used instead of
spin_lock_irqsave/spin_unlock_irqrestore.
spin_lock_irq and spin_unlock_irq are faster because they don't need to
push and pop the flags register.
Compilers with branch protection support can be configured to enable it by
default, it is likely that distributions will do this as part of deploying
branch protection system wide. As well as the slight overhead from having
some extra NOPs for unused branch protection features this can cause more
serious problems when the kernel is providing pointer authentication to
userspace but not built for pointer authentication itself. In that case our
switching of keys for userspace can affect the kernel unexpectedly, causing
pointer authentication instructions in the kernel to corrupt addresses.
To ensure that we get consistent and reliable behaviour always explicitly
initialise the branch protection mode, ensuring that the kernel is built
the same way regardless of the compiler defaults.
[This is a reworked version of 12e00d45d4acaba7ab3e22 ("arm64: Always
force a branch protection mode when the compiler has one") for backport.
Kernels prior to e6e9da7c1d4e ("arm64: compile the kernel with ptrauth
return address signing") don't have any Makefile machinery for forcing
on pointer auth but still have issues if the compiler defaults it on so
need this reworked version. -- broonie]
Fixes: 79f945fbc9151 (arm64: add basic pointer authentication support) Reported-by: Szabolcs Nagy <szabolcs.nagy@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
[catalin.marinas@arm.com: remove Kconfig option in favour of Makefile check] Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declaring setjmp()/longjmp() as taking longs makes the signature
non-standard, and makes clang complain. In the past, this has been
worked around by adding -ffreestanding to the compile flags.
The implementation looks like it only ever propagates the value
(in longjmp) or sets it to 1 (in setjmp), and we only call longjmp
with integer parameters.
This allows removing -ffreestanding from the compilation flags.
Generic protection fault type kernel panic is observed when user performs
soft (ordered) HBA unplug operation while IOs are running on drives
connected to HBA.
When user performs ordered HBA removal operation, the kernel calls PCI
device's .remove() call back function where driver is flushing out all the
outstanding SCSI IO commands with DID_NO_CONNECT host byte and also unmaps
sg buffers allocated for these IO commands.
However, in the ordered HBA removal case (unlike of real HBA hot removal),
HBA device is still alive and hence HBA hardware is performing the DMA
operations to those buffers on the system memory which are already unmapped
while flushing out the outstanding SCSI IO commands and this leads to
kernel panic.
Don't flush out the outstanding IOs from .remove() path in case of ordered
removal since HBA will be still alive in this case and it can complete the
outstanding IOs. Flush out the outstanding IOs only in case of 'physical
HBA hot unplug' where there won't be any communication with the HBA.
During shutdown also it is possible that HBA hardware can perform DMA
operations on those outstanding IO buffers which are completed with
DID_NO_CONNECT by the driver from .shutdown(). So same above fix is applied
in shutdown path as well.
It is safe to drop the outstanding commands when HBA is inaccessible such
as when permanent PCI failure happens, when HBA is in non-operational
state, or when someone does a real HBA hot unplug operation. Since driver
knows that HBA is inaccessible during these cases, it is safe to drop the
outstanding commands instead of waiting for SCSI error recovery to kick in
and clear these outstanding commands.
Link: https://lore.kernel.org/r/1585302763-23007-1-git-send-email-sreekanth.reddy@broadcom.com Fixes: 688a7dcf691f ("scsi: mpt3sas: wait for and flush running commands on shutdown/unload") Cc: stable@vger.kernel.org #v4.14.174+ Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit reduced the amount of code that is run before we
setup a paca. However there are still a few remaining functions that
run with no paca, or worse, with an arbitrary value in r13 that will
be used as a paca pointer.
In particular the stack protector canary is stored in the paca, so if
stack protector is activated for any of these functions we will read
the stack canary from wherever r13 points. If r13 happens to point
outside of memory we will get a machine check / checkstop.
For example if we modify initialise_paca() to trigger stack
protection, and then boot in the mambo simulator with r13 poisoned in
skiboot before calling the kernel:
kprobe is not prepared to handle events in real mode and functions
running in real mode should have been blacklisted, so kprobe_handler()
can safely bail out telling 'this trap is not mine' for any trap that
happened while in real-mode.
If the trap happened with MSR_IR or MSR_DR cleared, return 0
immediately.
Currently we set up the paca after parsing the device tree for CPU
features. Prior to that, r13 contains random data, which means there
is random data in r13 while we're running the generic dt parsing code.
This random data varies depending on whether we boot through a vmlinux
or a zImage: for the vmlinux case it's usually around zero, but for
zImages we see random values like 912a72603d420015.
This is poor practice, and can also lead to difficult-to-debug
crashes. For example, when kcov is enabled, the kcov instrumentation
attempts to read preempt_count out of the current task, which goes via
the paca. This then crashes in the zImage case.
Similarly stack protector can cause crashes if r13 is bogus, by
reading from the stack canary in the paca.
To resolve this:
- move the paca setup to before the CPU feature parsing.
- because we no longer have access to CPU feature flags in paca
setup, change the HV feature test in the paca setup path to consider
the actual value of the MSR rather than the CPU feature.
Translations get switched on once we leave early_setup, so I think
we'd already catch any other cases where the paca or task aren't set
up.
Boot tested on a P9 guest and host.
Fixes: b1b71234af76 ("powerpc: Enable kcov") Fixes: 76b1ecf1de15 ("powerpc/64: add stack protector support") Cc: stable@vger.kernel.org # v4.20+ Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Daniel Axtens <dja@axtens.net>
[mpe: Reword comments & change log a bit to mention stack protector] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200320032116.1024773-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a CPU is brought up, an IPI number is allocated and recorded
under the XIVE CPU structure. Invalid IPI numbers are tracked with
interrupt number 0x0.
On the PowerNV platform, the interrupt number space starts at 0x10 and
this works fine. However, on the sPAPR platform, it is possible to
allocate the interrupt number 0x0 and this raises an issue when CPU 0
is unplugged. The XIVE spapr driver tracks allocated interrupt numbers
in a bitmask and it is not correctly updated when interrupt number 0x0
is freed. It stays allocated and it is then impossible to reallocate.
Fix by using the XIVE_BAD_IRQ value instead of zero on both platforms.
Reported-by: David Gibson <david@gibson.dropbear.id.au> Fixes: 7a69a82db40b ("powerpc/xive: guest exploitation of the XIVE interrupt controller") Cc: stable@vger.kernel.org # v4.14+ Signed-off-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Tested-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200306150143.5551-2-clg@kaod.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H_PAGE_THP_HUGE is used to differentiate between a THP hugepage and
hugetlb hugepage entries. The difference is WRT how we handle hash
fault on these address. THP address enables MPSS in segments. We want
to manage devmap hugepage entries similar to THP pt entries. Hence use
H_PAGE_THP_HUGE for devmap huge PTE entries.
With current code while handling hash PTE fault, we do set is_thp =
true when finding devmap PTE huge PTE entries.
Current code also does the below sequence we setting up huge devmap
entries.
entry = pmd_mkhuge(pfn_t_pmd(pfn, prot));
if (pfn_t_devmap(pfn))
entry = pmd_mkdevmap(entry);
In that case we would find both H_PAGE_THP_HUGE and PAGE_DEVMAP set
for huge devmap PTE entries. This results in false positive error like
below.
kernel BUG at /home/kvaneesh/src/linux/mm/memory.c:4321!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 56 PID: 67996 Comm: t_mmap_dio Not tainted 5.6.0-rc4-59640-g371c804dedbc #128
....
NIP [c00000000044c9e4] __follow_pte_pmd+0x264/0x900
LR [c0000000005d45f8] dax_writeback_one+0x1a8/0x740
Call Trace:
str_spec.74809+0x22ffb4/0x2d116c (unreliable)
dax_writeback_one+0x1a8/0x740
dax_writeback_mapping_range+0x26c/0x700
ext4_dax_writepages+0x150/0x5a0
do_writepages+0x68/0x180
__filemap_fdatawrite_range+0x138/0x180
file_write_and_wait_range+0xa4/0x110
ext4_sync_file+0x370/0x6e0
vfs_fsync_range+0x70/0xf0
sys_msync+0x220/0x2e0
system_call+0x5c/0x68
This is because our pmd_trans_huge check doesn't exclude _PAGE_DEVMAP.
To make this all consistent, update pmd_mkdevmap to set
H_PAGE_THP_HUGE and pmd_trans_huge check now excludes _PAGE_DEVMAP
correctly.
Fixes: 7daf6e1b1049 ("powerpc/mm: Add devmap support for ppc64") Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200313094842.351830-1-aneesh.kumar@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation, the call to loadcam_multi() is wrapped
between switch_to_as1() and restore_to_as0() calls so, when it tries
to create its own temporary AS=1 TLB1 entry, it ends up duplicating
the existing one created by switch_to_as1(). Add a check to skip
creating the temporary entry if already running in AS=1.
Fixes: e3cd6075c709 ("powerpc/85xx: Load all early TLB entries at once") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Acked-by: Scott Wood <oss@buserror.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200123111914.2565-1-laurentiu.tudor@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can also cause us to unnecessarily save non-volatile GPRs again in
save_nvgprs(), which shouldn't be problematic but is still wrong.
It's also possible it could trick the syscall restart machinery, which
relies on regs->trap not being == 0xc00 (see b9b8619ea862 ("powerpc:
fix double syscall restarts")), though I haven't been able to make
that happen.
Finally it doesn't match the behaviour of the non-TM case, in
restore_sigcontext() which zeroes regs->trap.
So change restore_tm_sigcontexts() to zero regs->trap.
This was discovered while testing Nick's upcoming rewrite of the
syscall entry path. In that series the call to save_nvgprs() prior to
signal handling (do_notify_resume()) is removed, which leaves the
low-bit of regs->trap uncleared which can then trigger the FULL_REGS()
WARNs in setup_tm_sigcontexts().
Fixes: f68633cf0b04 ("powerpc: Add new transactional memory state to the signal context") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200401023836.3286664-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0e9a663c80824 ("xen-blkfront: switch kcalloc to kvcalloc for
large array allocation") didn't fix the issue it was meant to, as the
flags for allocating the memory are GFP_NOIO, which will lead the
memory allocation falling back to kmalloc().
So instead of GFP_NOIO use GFP_KERNEL and do all the memory allocation
in blkfront_setup_indirect() in a memalloc_noio_{save,restore} section.
Fixes: 0e9a663c80824 ("xen-blkfront: switch kcalloc to kvcalloc for large array allocation") Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Link: https://lore.kernel.org/r/20200403090034.8753-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait_event() function is used to detect command completion.
When send_guid_cmd() returns an error, smi_send() has not been
called to send data. Therefore, wait_event() should not be used
on the error path, otherwise it will cause the following warning:
During system resume from suspend, this can be observed on ASM1062 PMP
controller:
ata10.01: SATA link down (SStatus 0 SControl 330)
ata10.02: hard resetting link
ata10.02: SATA link down (SStatus 0 SControl 330)
ata10.00: configured for UDMA/133
Kernel panic - not syncing: stack-protector: Kernel
in: sata_pmp_eh_recover+0xa2b/0xa40
Since sata_pmp_eh_recover_pmp() doens't set rc when ATA_DFLAG_DETACH is
set, sata_pmp_eh_recover() continues to run. During retry it triggers
the stack protector.
Set correct rc in sata_pmp_eh_recover_pmp() to let sata_pmp_eh_recover()
jump to pmp_fail directly.
When removing files containing extended attributes, the hfsplus driver may
remove the wrong entries from the attributes b-tree, causing major
filesystem damage and in some cases even kernel crashes.
To remove a file, all its extended attributes have to be removed as well.
The driver does this by looking up all keys in the attributes b-tree with
the cnid of the file. Each of these entries then gets deleted using the
key used for searching, which doesn't contain the attribute's name when it
should. Since the key doesn't contain the name, the deletion routine will
not find the correct entry and instead remove the one in front of it. If
parent nodes have to be modified, these become corrupt as well. This
causes invalid links and unsorted entries that not even macOS's fsck_hfs
is able to fix.
To fix this, modify the search key before an entry is deleted from the
attributes b-tree by copying the found entry's key into the search key,
therefore ensuring that the correct entry gets removed from the tree.
Signed-off-by: Simon Gander <simon@tuxera.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Anton Altaparmakov <anton@tuxera.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200327155541.1521-1-simon@tuxera.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cpufreq driver has a use-after-free that we can hit if:
a) There's an OCC message pending when the notifier is registered, and
b) The cpufreq driver fails to register with the core.
When a) occurs the notifier schedules a workqueue item to handle the
message. The backing work_struct is located on chips[].throttle and
when b) happens we clean up by freeing the array. Once we get to
the (now free) queued item and the kernel crashes.
Fixes: 2686bea8e92b ("cpufreq: powernv: Fix bugs in powernv_cpufreq_{init/exit}") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200206062622.28235-1-oohall@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "module autoloading fixes and cleanups", v5.
This series fixes a bug where request_module() was reporting success to
kernel code when module autoloading had been completely disabled via
'echo > /proc/sys/kernel/modprobe'.
It also addresses the issues raised on the original thread
(https://lkml.kernel.org/lkml/20200310223731.126894-1-ebiggers@kernel.org/T/#u)
bydocumenting the modprobe sysctl, adding a self-test for the empty path
case, and downgrading a user-reachable WARN_ONCE().
This patch (of 4):
It's long been possible to disable kernel module autoloading completely
(while still allowing manual module insertion) by setting
/proc/sys/kernel/modprobe to the empty string.
This can be preferable to setting it to a nonexistent file since it
avoids the overhead of an attempted execve(), avoids potential
deadlocks, and avoids the call to security_kernel_module_request() and
thus on SELinux-based systems eliminates the need to write SELinux rules
to dontaudit module_request.
However, when module autoloading is disabled in this way,
request_module() returns 0. This is broken because callers expect 0 to
mean that the module was successfully loaded.
Apparently this was never noticed because this method of disabling
module autoloading isn't used much, and also most callers don't use the
return value of request_module() since it's always necessary to check
whether the module registered its functionality or not anyway.
But improperly returning 0 can indeed confuse a few callers, for example
get_fs_type() in fs/filesystems.c where it causes a WARNING to be hit:
if (!fs && (request_module("fs-%.*s", len, name) == 0)) {
fs = __get_fs_type(name, len);
WARN_ONCE(!fs, "request_module fs-%.*s succeeded, but still no fs?\n", len, name);
}
This is easily reproduced with:
echo > /proc/sys/kernel/modprobe
mount -t NONEXISTENT none /
It causes:
request_module fs-NONEXISTENT succeeded, but still no fs?
WARNING: CPU: 1 PID: 1106 at fs/filesystems.c:275 get_fs_type+0xd6/0xf0
[...]
This should actually use pr_warn_once() rather than WARN_ONCE(), since
it's also user-reachable if userspace immediately unloads the module.
Regardless, request_module() should correctly return an error when it
fails. So let's make it return -ENOENT, which matches the error when
the modprobe binary doesn't exist.
I've also sent patches to document and test this case.
The Acer Aspire 5738z has a button to disable (and re-enable) the
touchpad next to the touchpad.
When this button is pressed a LED underneath indicates that the touchpad
is disabled (and an event is send to userspace and GNOME shows its
touchpad enabled / disable OSD thingie).
So far so good, but after re-enabling the touchpad it no longer works.
The laptop does not have an external ps2 port, so mux mode is not needed
and disabling mux mode fixes the touchpad no longer working after toggling
it off and back on again, so lets add this laptop model to the nomux list.
Python 3.8 changed the output of 'python-config --ldflags' to no longer
include the '-lpythonX.Y' flag (this apparently fixed an issue loading
modules with a statically linked Python executable). The libpython
feature check in linux/build/feature fails if the Python library is not
included in FEATURE_CHECK_LDFLAGS-libpython variable.
This adds a check in the Makefile to determine if PYTHON_CONFIG accepts
the '--embed' flag and passes that flag alongside '--ldflags' if so.
tools/perf is the only place the libpython feature check is used.
Signed-off-by: Sam Lunt <samuel.j.lunt@gmail.com> Tested-by: He Zhe <zhe.he@windriver.com> Link: http://lore.kernel.org/lkml/c56be2e1-8111-9dfe-8298-f7d0f9ab7431@windriver.com Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: trivial@kernel.org Cc: stable@kernel.org Link: http://lore.kernel.org/lkml/20200131181123.tmamivhq4b7uqasr@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux fallocate(2) with FALLOC_FL_PUNCH_HOLE mode set, its offset can
exceed the inode size. Ocfs2 now doesn't allow that offset beyond inode
size. This restriction is not necessary and violates fallocate(2)
semantics.
If fallocate(2) offset is beyond inode size, just return success and do
nothing further.
Signed-off-by: Changwei Ge <chge@linux.alibaba.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200407082754.17565-1-chge@linux.alibaba.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After request_module(), nothing is stopping the module from being
unloaded until someone takes a reference to it via try_get_module().
The WARN_ONCE() in get_fs_type() is thus user-reachable, via userspace
running 'rmmod' concurrently.
Since WARN_ONCE() is for kernel bugs only, not for user-reachable
situations, downgrade this warning to pr_warn_once().
Keep it printed once only, since the intent of this warning is to detect
a bug in modprobe at boot time. Printing the warning more than once
wouldn't really provide any useful extra information.
Fixes: dc1b34def6a6 ("fs: warn in case userspace lied about modprobe return") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Jessica Yu <jeyu@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jeff Vander Stoep <jeffv@google.com> Cc: Jessica Yu <jeyu@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: NeilBrown <neilb@suse.com> Cc: <stable@vger.kernel.org> [4.13+] Link: http://lkml.kernel.org/r/20200312202552.241885-3-ebiggers@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to ensure that we create the mirror requests before calling
nfs_pageio_add_request_mirror() on the request we are adding.
Otherwise, we can end up with a use-after-free if the call to
nfs_pageio_add_request_mirror() triggers I/O.
Userspace should be able to monitor nfsd/clients/ to see when clients
come and go, but we're failing to send fsnotify events.
Cc: stable@kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Taking closer look at the code, I can see that for_each_drmem_lmb is a
macro expanding into `for (lmb = &drmem_info->lmbs[0]; lmb <=
&drmem_info->lmbs[drmem_info->n_lmbs - 1]; lmb++)`. When drmem_info->lmbs
is NULL, the loop would iterate through the whole address range if it
weren't stopped by the NULL pointer dereference on the next line.
This patch aligns for_each_drmem_lmb and for_each_drmem_lmb_in_range
macro behavior with the common C semantics, where the end marker does
not belong to the scanned range, and alters get_lmb_range() semantics.
As a side effect, the wraparound observed in the crash is prevented.
Fixes: c78283af043c ("powerpc/mm: Separate ibm, dynamic-memory data from DT format") Cc: stable@vger.kernel.org # v4.16+ Signed-off-by: Libor Pechacek <lpechacek@suse.cz> Signed-off-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200131132829.10281-1-msuchanek@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the fw_write_wait default case true since presumably all new
gfx9 asics will have updated firmware. That is using unique WAIT_REG_MEM
packet with opration=1.
Signed-off-by: Aaron Liu <aaron.liu@amd.com> Tested-by: Aaron Liu <aaron.liu@amd.com> Tested-by: Yuxian Dai <Yuxian.Dai@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1.Using the FCLK DPM table to set the MCLK for DPM states consist of
three entities:
FCLK
UCLK
MEMCLK
All these three clk change together, MEMCLK from FCLK, so use the fclk
frequency.
2.we should show the current working clock freqency from clock table metric
Signed-off-by: Yuxian Dai <Yuxian.Dai@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_pci_alloc/drm_pci_free are very thin wrappers around the core dma
facilities, and we have no special reason within the drm layer to behave
differently. In particular, since
Since commit 682a742ed79d ("driver core: platform: Add an error
message to platform_get_irq*()"), platform_get_irq() calls dev_err()
on an error. As we enumerate all interrupts until platform_get_irq()
fails, we now systematically get a message such as:
"vfio-platform fff51000.ethernet: IRQ index 3 not found" which is
a false positive.
Let's use platform_get_irq_optional() instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com> Cc: stable@vger.kernel.org # v5.3+ Reviewed-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f3cdbe13bf63 ("tools/selftest/vm: allow choosing mem size and page
size in map_hugetlb") added the possibility to change the size of memory
mapped for the test, but left the read and write test using the default
value. This is unnoticed when mapping a length greater than the default
one, but segfaults otherwise.
Fix read_bytes() and write_bytes() by giving them the real length.
Also fix the call to munmap().
Fixes: f3cdbe13bf63 ("tools/selftest/vm: allow choosing mem size and page size in map_hugetlb") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Shuah Khan <shuah@kernel.org> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/9a404a13c871c4bd0ba9ede68f69a1225180dd7e.1580978385.git.christophe.leroy@c-s.fr Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was noticed that mlock2 tests are failing after 09e86dc6ae493 ("mm,
mlock, vmscan: no more skipping pagevecs") because the patch has changed
the timing on when the page is added to the unevictable LRU list and thus
gains the unevictable page flag.
The test was just too dependent on the implementation details which were
true at the time when it was introduced. Page flags and the timing when
they are set is something no userspace should ever depend on. The test
should be testing only for the user observable contract of the tested
syscalls. Those are defined pretty well for the mlock and there are other
means for testing them. In fact this is already done and testing for page
flags can be safely dropped to achieve the aimed purpose. Present bits
can be checked by /proc/<pid>/smaps RSS field and the locking state by
VmFlags although I would argue that Locked: field would be more
appropriate.
Drop all the page flag machinery and considerably simplify the test. This
should be more robust for future kernel changes while checking the
promised contract is still valid.
Fixes: 09e86dc6ae493 ("mm, mlock, vmscan: no more skipping pagevecs") Reported-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Rafael Aquini <aquini@redhat.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: Eric B Munson <emunson@akamai.com> Cc: Shuah Khan <shuah@kernel.org> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200324154218.GS19542@dhcp22.suse.cz Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For thumb instructions, call_undef_hook() in traps.c first reads a u16,
and if the u16 indicates a T32 instruction (u16 >= 0xe800), a second
u16 is read, which then makes up the the lower half-word of a T32
instruction. For T16 instructions, the second u16 is not read,
which makes the resulting u32 opcode always have the upper half set to
0.
However, having the upper half of instr_mask in the undef_hook set to 0
masks out the upper half of all thumb instructions - both T16 and T32.
This results in trapped T32 instructions with the lower half-word equal
to the T16 encoding of setend (b650) being matched, even though the upper
half-word is not 0000 and thus indicates a T32 opcode.
An example of such a T32 instruction is eaa0b650, which should raise a
SIGILL since T32 instructions with an eaa prefix are unallocated as per
Arm ARM, but instead works as a SETEND because the second half-word is set
to b650.
This patch fixes the issue by extending instr_mask to include the
upper u32 half, which will still match T16 instructions where the upper
half is 0, but not T32 instructions.
Fixes: 772d9c885988 ("arm64: Emulate SETEND for AArch32 tasks") Cc: <stable@vger.kernel.org> # 4.0.x- Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Fredrik Strupe <fredrik@strupe.net> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TI sci-clk driver can scan the DT for all clocks provided by system
firmware and does this by checking the clocks property of all nodes, so
we must add this to the dwc3 nodes so USB clocks are available.
Without this USB does not work with latest system firmware i.e.
[ 1.714662] clk: couldn't get parent clock 0 for /interconnect@100000/dwc3@4020000
Fixes: fbbcd5bdf1aba ("arm64: dts: ti: k3-am6: add USB suppor") Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Cc: stable@kernel.org Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent changes in the SPI core and the SPI-GPIO driver revealed that the
GPIO lines for the LD9040 LCD controller on the UniversalC210 board are
defined incorrectly. Fix the polarity for those lines to match the old
behavior and hardware requirements to fix LCD panel operation with
recent kernels.
Cc: <stable@vger.kernel.org> # 5.0.x Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto-Hibern8 may be disabled by some vendors or sysfs in runtime even if
Auto-Hibern8 capability is supported by host. If Auto-Hibern8 capability is
supported by host but not actually enabled, Auto-Hibern8 error shall not
happen.
To fix this, provide a way to detect if Auto-Hibern8 is actually enabled
first, and bypass Auto-Hibern8 disabling case in
ufshcd_is_auto_hibern8_error().
Fixes: 820b41f83cdf ("scsi: ufs: Add error-handling of Auto-Hibernate") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200129105251.12466-4-stanley.chu@mediatek.com Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before that, the user had to use the sysfs attribute "port_add" of an FCP
device (adapter) to add and open remote (target) ports, even for the remote
peer port in point-to-point topology. That code path did a proper port open
recovery trigger taking the erp_lock.
Since above commit, a new helper function zfcp_erp_open_ptp_port()
performed an UNlocked port open recovery trigger. This can race with other
parallel recovery triggers. In zfcp_erp_action_enqueue() this could corrupt
e.g. adapter->erp_total_count or adapter->erp_ready_head.
As already found for fabric topology in v4.17 commit 18d705b9389f ("scsi:
zfcp: fix infinite iteration on ERP ready list"), there was an endless loop
during tracing of rport (un)block. A subsequent v4.18 commit f4215a23ff50
("scsi: zfcp: assert that the ERP lock is held when tracing a recovery
trigger") introduced a lockdep assertion for that case.
As a side effect, that lockdep assertion now uncovered the unlocked code
path for PtP. It is from within an adapter ERP action:
zfcp_erp_strategy[1479] intentionally DROPs erp lock around
zfcp_erp_strategy_do_action()
zfcp_erp_strategy_do_action[1441] NO erp lock
zfcp_erp_adapter_strategy[876] NO erp lock
zfcp_erp_adapter_strategy_open[855] NO erp lock
zfcp_erp_adapter_strategy_open_fsf[806]NO erp lock
zfcp_erp_adapter_strat_fsf_xconf[772] erp lock only around
zfcp_erp_action_to_running(),
BUT *_not_* around
zfcp_erp_enqueue_ptp_port()
zfcp_erp_enqueue_ptp_port[728] BUG: *_not_* taking erp lock
_zfcp_erp_port_reopen[432] assumes to be called with erp lock
zfcp_erp_action_enqueue[314] assumes to be called with erp lock
zfcp_dbf_rec_trig[288] _checks_ to be called with erp lock:
lockdep_assert_held(&adapter->erp_lock);
It causes the following lockdep warning:
WARNING: CPU: 2 PID: 775 at drivers/s390/scsi/zfcp_dbf.c:288
zfcp_dbf_rec_trig+0x16a/0x188
no locks held by zfcperp0.0.17c0/775.
Fix this by using the proper locked recovery trigger helper function.
Remove the auth tag size from cryptlen before mapping the destination
in out-of-place AEAD decryption thus resolving a crash with
extended testmgr tests.
Make sure to only add the size of the auth tag to the source mapping
for encryption if it is an in-place operation. Failing to do this
previously caused us to try and map auth size len bytes from a NULL
mapping and crashing if both the cryptlen and assoclen are zero.
Since in the software implementation of XTS-AES there is
no notion of sector every input length is processed the same way.
CAAM implementation has the notion of sector which causes different
results between the software implementation and the one in CAAM
for input lengths bigger than 512 bytes.
Increase sector size to maximum value on 16 bits.
Fixes: b72196887d23 ("crypto: caam - add support for acipher xts(aes)") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HW generates a Data Size error for chacha20 requests that are not
a multiple of 64B, since algorithm state (AS) does not have
the FINAL bit set.
Since updating req->iv (for chaining) is not required,
modify skcipher descriptors to set the FINAL bit for chacha20.
[Note that for skcipher decryption we know that ctx1_iv_off is 0,
which allows for an optimization by not checking algorithm type,
since append_dec_op1() sets FINAL bit for all algorithms except AES.]
Also drop the descriptor operations that save the IV.
However, in order to keep code logic simple, things like
S/G tables generation etc. are not touched.
xas_for_each_marked() is using entry == NULL as a termination condition
of the iteration. When xas_for_each_marked() is used protected only by
RCU, this can however race with xas_store(xas, NULL) in the following
way:
TASK1 TASK2
page_cache_delete() find_get_pages_range_tag()
xas_for_each_marked()
xas_find_marked()
off = xas_find_chunk()
And thus xas_for_each_marked() terminates prematurely possibly leading
to missed entries in the iteration (translating to missing writeback of
some pages or a similar problem).
If we find a NULL entry that has been marked, skip it (unless we're trying
to allocate an entry).
Reported-by: Jan Kara <jack@suse.cz> CC: stable@vger.kernel.org Fixes: f0c6bd3c48d9 ("page cache: Convert delete_batch to XArray") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log