As comment of pci_get_device() says, it returns a pci_device with its
refcount increased. We need to call pci_dev_put() to decrease the
refcount. Save the return value of pci_get_device() and call
pci_dev_put() to decrease the refcount.
Fixes: 66ef56495170 ("mt76: mt7915: add support for using a secondary PCIe link for gen1") Fixes: d1b33ea8e850 ("mt76: mt7915: add device id for mt7916") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure the nss is valid for nss_delta array. Return zero
if the index is invalid.
Coverity message:
Event overrun-call: Overrunning callee's array of size 4 by passing
argument "n_chains" (which evaluates to 15) in call to
"mt76_tx_power_nss_delta".
int delta = mt76_tx_power_nss_delta(n_chains);
Fixes: 474e110abac0 ("mt76: fix rounding issues on converting per-chain and combined txpower") Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
mt7915 does not have a per-band number of chains unlike the other chips,
it only has a total number of chains. Yet the current code would
consider the total number as a per-band number.
For example, it would report that a 2x2 + 2x2 DBDC card have 4 chains on
each band and set chainmask to 0b1111 for the first interface and 0b11110000 for the second.
Fixes: 73ab3bc0157d ("mt76: mt7915: add support for MT7986") Co-developed-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rework tx paths and streams init part to improve readability, and make
sure that the available tx streams should be smaller than or equal to
the available tx paths.
Group 3 in RxD is disabled in monitor mode. We should use the group 5 in
RxD instead to fix antenna signal way off issue, e.g we would see the
incorrect antenna signal value in wireshark. On the other hand, Group 5
wouldn't be used in STA or AP mode, so the patch shouldn't cause any
harm to those modes.
Fixes: 66202b90817b ("mt76: mt7921: fix up the monitor mode") Reported-by: Adrian Granados <agranados@gmail.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
In regulatory_init_db(), when it's going to return a error, reg_pdev
should be unregistered. When load_builtin_regdb_keys() fails it doesn't
do it and makes cfg80211 can't be reload with report:
As the nla_nest_start() may fail with NULL returned, the return value needs
to be checked.
Fixes: e4ff4b1fbd10 ("wifi: nl80211: expose link information for interfaces") Signed-off-by: Yuan Can <yuancan@huawei.com> Link: https://lore.kernel.org/r/20221129014211.56558-1-yuancan@huawei.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 13bca5fb5e26 ("spi: Optionally use GPIO descriptors for CS GPIOs")
has changed the user-space interface so that bogus SPI_CS_HIGH started
to appear in the mask returned by SPI_IOC_RD_MODE even for active-low CS
pins. Commit 171b0772222f
("spi: spidev: Fix CS polarity if GPIO descriptors are used") fixed only
SPI_IOC_WR_MODE part of the problem. Let's fix SPI_IOC_RD_MODE
symmetrically.
Fixes: 13bca5fb5e26 ("spi: Optionally use GPIO descriptors for CS GPIOs") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com> Link: https://lore.kernel.org/r/20221130162927.539512-1-alexander.sverdlin@siemens.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "ignore_updelay" variable needs to be initialized to false.
Fixes: 227b5e0a3095 ("bonding: fix link recovery in mode 2 when updelay is nonzero") Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/Y4SWJlh3ohJ6EPTL@kili Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When redirecting, we use sk_msg_to_ingress() to get the BPF_F_INGRESS
flag from the msg->flags. If apply_bytes is used and it is larger than
the current data being processed, sk_psock_msg_verdict() will not be
called when sendmsg() is called again. At this time, the msg->flags is 0,
and we lost the BPF_F_INGRESS flag.
So we need to save the BPF_F_INGRESS flag in sk_psock and use it when
redirection.
Fixes: 995b1a2f7b09 ("bpf: sockmap redirect ingress support") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/1669718441-2654-3-git-send-email-yangpc@wangsu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In tcp_bpf_send_verdict() redirection, the eval variable is assigned to
__SK_REDIRECT after the apply_bytes data is sent, if msg has more_data,
sock_put() will be called multiple times.
We should reset the eval variable to __SK_NONE every time more_data
starts.
This causes:
IPv4: Attempt to release TCP socket in state 1 00000000b4c925d7
------------[ cut here ]------------
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 5 PID: 4482 at lib/refcount.c:25 refcount_warn_saturate+0x7d/0x110
Modules linked in:
CPU: 5 PID: 4482 Comm: sockhash_bypass Kdump: loaded Not tainted 6.0.0 #1
Hardware name: Red Hat KVM, BIOS 1.11.0-2.el7 04/01/2014
Call Trace:
<TASK>
__tcp_transmit_skb+0xa1b/0xb90
? __alloc_skb+0x8c/0x1a0
? __kmalloc_node_track_caller+0x184/0x320
tcp_write_xmit+0x22a/0x1110
__tcp_push_pending_frames+0x32/0xf0
do_tcp_sendpages+0x62d/0x640
tcp_bpf_push+0xae/0x2c0
tcp_bpf_sendmsg_redir+0x260/0x410
? preempt_count_add+0x70/0xa0
tcp_bpf_send_verdict+0x386/0x4b0
tcp_bpf_sendmsg+0x21b/0x3b0
sock_sendmsg+0x58/0x70
__sys_sendto+0xfa/0x170
? xfd_validate_state+0x1d/0x80
? switch_fpu_return+0x59/0xe0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 156bb88c0035 ("tcp_bpf: Fix one concurrency problem in the tcp_bpf_send_verdict function") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/1669718441-2654-2-git-send-email-yangpc@wangsu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
icmp conntrack will set icmp redirects as RELATED, but icmpv6 will not
do this.
For icmpv6, only icmp errors (code <= 128) are examined for RELATED state.
ICMPV6 Redirects are part of neighbour discovery mechanism, those are
handled by marking a selected subset (e.g. neighbour solicitations) as
UNTRACKED, but not REDIRECT -- they will thus be flagged as INVALID.
Add minimal support for REDIRECTs. No parsing of neighbour options is
added for simplicity, so this will only check that we have the embeeded
original header (ND_OPT_REDIRECT_HDR), and then attempt to do a flow
lookup for this tuple.
Also extend the existing test case to cover redirects.
Fixes: b0bbff62ec62 ("[NETFILTER]: Add nf_conntrack subsystem.") Reported-by: Eric Garver <eric@garver.life> Link: https://github.com/firewalld/firewalld/issues/1046 Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Eric Garver <eric@garver.life> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it.
Fixes: 82101a663476 ("clk: visconti: Add support common clock driver and reset driver") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Link: https://lore.kernel.org/r/20221122152353.204132-1-xiujianfeng@huawei.com Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by going to
err_pm instead of err_clk.
Fixes:de07d1146a4ef ("ASoC: pcm512x: Support mastering BCLK/LRCLK using the PLL")
When (size != 0 || ptrs->lvds_ entries != 3), the program tries to
free() the ptrs. However, the ptrs is not created by calling kzmalloc(),
but is obtained by pointer offset operation.
This may lead to memory leaks or undefined behavior.
Fix this by replacing the arguments of kfree() with ptrs_block.
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: 7acade7b3a33 ("drm/amdgpu: add core driver (v4)") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in radeon_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: ae924ec11c9d ("drm/radeon: handle non-VGA class pci devices with ATRM") Fixes: 6c4ad395657d ("drm/radeon: split ATRM support out from the ATPX handler (v3)") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Return true early if ASIC is in BACO state already, no need
to talk to SMU. It can fix the issue that driver was not
calling BACO exit at all in runtime pm resume, and a timing
issue leading to a PCI AER error happened eventually.
It seems like CLK_INFRA_ADC_FRC_CK always need to be enabled for
CLK_INFRA_ADC_26M_CK to work. Instead of adding this dependency to the
mtk-thermal and mt6577_auxadc drivers, add dependency to the clock
driver clk-mt7986-infracfg.c.
Fixes: 922f4f9b0f3c ("clk: mediatek: add mt7986 clock support") Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/5e55012567da74870e1fb2edc2dc513b5821e523.1666801017.git.daniel@makrotopia.org Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We see kernel crashes and lockups and KASAN errors related to ax210
firmware crashes. One of the KASAN dumps pointed at the tx path,
and it appears there is indeed a way to double-free an skb.
If iwl_mvm_tx_skb_sta returns non-zero, then the 'skb' sent into the
method will be freed. But, in case where we build TSO skb buffer,
the skb may also be freed in error case. So, return 0 in that particular
error case and do cleanup manually.
BUG: KASAN: use-after-free in __list_del_entry_valid+0x12/0x90
iwlwifi 0000:06:00.0: 0x00000000 | tsf hi
Read of size 8 at addr ffff88813cfa4ba0 by task btserver/9650
The buggy address belongs to the object at ffff88813cfa4b40
which belongs to the cache skbuff_fclone_cache of size 472
The buggy address is located 96 bytes inside of
472-byte region [ffff88813cfa4b40, ffff88813cfa4d18)
Memory state around the buggy address: ffff88813cfa4a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88813cfa4b00: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
>ffff88813cfa4b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88813cfa4c00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88813cfa4c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Commit 8be14edf5564 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width")
introduced a line where the pointer returned by ieee80211_find_sta() is
used after rcu_read_unlock().
Move rcu_read_unlock() a bit lower to fix this.
Fixes: 8be14edf5564 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width") Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/3c82ad09-7593-3be1-1d2c-e58505fb43cb@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
urbs does not be freed in exception paths in __lf_x_usb_enable_rx().
That will trigger memory leak. To fix it, add kfree() for urbs within
"error" label. Compile tested only.
Fixes: 0f2cae64700e ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221119051900.1192401-1-william.xuanziyang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're asked to recover open state while a delegation return is
outstanding, then the state manager thread cannot use a cached open, so
if the server returns a delegation, we can end up deadlocked behind the
pending delegreturn.
To avoid this problem, let's just ask the server not to give us a
delegation unless we're explicitly reclaiming one.
Fixes: e48116042bd1 ("NFSv4: nfs4_open_recover_helper() must set share access") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the commit commit 1eae9f2ee797 ("drm/msm/mdp5: stop overriding
drvdata") reading the MDP5 hw revision on db410c will crash the board
as the MDSS_GDSC is not enabled. Revert a part of the offending commit
(moving rpm enablement) and set priv->kms earlier. This make it possible
to use pm_runtime_get_sync() during read_mdp_hw_revision(), which will
power up both the MDP5 and MDSS devices.
Commit d0415b2529d8760ab ("[media] s5p-mfc: Core support for MFC v7")
which adds mfc v7 support for Exynos3250 and use the same compatible
string as used by Exynos5240 but both the IPs are a bit different in
terms of IP clock.
Add variant driver data based on the new compatible string
"samsung,exynos3250-mfc" for Exynos3250 SoC.
Suggested-by: Alim Akhtar <alim.akhtar@samsung.com> Fixes: d0415b2529d8 ("[media] s5p-mfc: Core support for MFC v7") Signed-off-by: Aakarsh Jain <aakarsh.jain@samsung.com> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver may can't get v4l2 buffer when lat or core decode timeout,
will lead to crash when call v4l2_m2m_buf_done to set dst buffer
(NULL pointer) done.
Fixes: 703c0ce786ea ("media: mediatek: vcodec: Refactor get and put capture buffer flow") Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
driver needs to cancel vpu before releasing the vpu instance,
so call v4l2_m2m_ctx_release() first,
to handle the redundant event triggered after m2m_ctx is released.
firmware should be waked up by start or configure command,
but there is a very small chance that firmware failed to wakeup.
in such case, try to wakeup firmware again by sending a noop command
This allows the device to probe and register its async subdev without
a sensor attached.
The rationale is that the parent driver might otherwise wait for the
subdev to be registered when it should be available (from the fwnode
graph endpoint perspective). This is generally not problematic when
the MIPI CSI-2 bridge is the only device attached to the parent, but
in the case of a CSI controller that can feed from both MIPI CSI-2
and parallel, it would prevent using the parallel sensor due to the
parent waiting for the MIPI CSI-2 subdev to register.
Fixes: 09a1b7256aed ("media: sunxi: Add support for the A83T MIPI CSI-2 controller") Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This allows the device to probe and register its async subdev without
a sensor attached.
The rationale is that the parent driver might otherwise wait for the
subdev to be registered when it should be available (from the fwnode
graph endpoint perspective). This is generally not problematic when
the MIPI CSI-2 bridge is the only device attached to the parent, but
in the case of a CSI controller that can feed from both MIPI CSI-2
and parallel, it would prevent using the parallel sensor due to the
parent waiting for the MIPI CSI-2 subdev to register.
Fixes: 7038a112b666 ("media: sunxi: Add support for the A31 MIPI CSI-2 controller") Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running as a Xen PV guest there is no need for setting up the
realmode trampoline, as realmode isn't supported in this environment.
Trying to setup the trampoline has been proven to be problematic in
some cases, especially when trying to debug early boot problems with
Xen requiring to keep the EFI boot-services memory mapped (some
firmware variants seem to claim basically all memory below 1Mb for boot
services).
Introduce new x86_platform_ops operations for that purpose, which can
be set to a NOP by the Xen PV specific kernel boot code.
[ bp: s/call_init_real_mode/do_init_real_mode/ ]
Fixes: 79a943d9e5fc ("x86, realmode: Relocator for realmode code") Suggested-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20221123114523.3467-1-jgross@suse.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_register_frontend(), dvb_register_device() is possible to fail
but its return value is ignored.
It will cause use-after-free when module is removed, because in
dvb_unregister_frontend() it tries to unregister a not registered
device.
BUG: KASAN: use-after-free in dvb_remove_device+0x18b/0x1f0 [dvb_core]
Read of size 4 at addr ffff88800dff4824 by task rmmod/428
CPU: 3 PID: 428 Comm: rmmod
Call Trace:
<TASK>
...
dvb_remove_device+0x18b/0x1f0 [dvb_core]
dvb_unregister_frontend+0x7b/0x130 [dvb_core]
vidtv_bridge_remove+0x6e/0x160 [dvb_vidtv_bridge]
...
Fix this by catching return value of dvb_register_device().
However the fe->refcount can't be put to zero immediately, because
there are still modules calling dvb_frontend_detach() when
dvb_register_frontend() fails.
while the imx8mn_enet_phy_sels list didn't contained audio_pll1_out for
source select bits 101b.
Fixes: e3a7483537b5b ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-6-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
while the imx8mn_sai2_sels list contained clk_ext3 and clk_ext4 for
source select bits 110b and 111b.
Fixes: e3a7483537b5b ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-5-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike audio_pll1 and audio_pll2, there is no video_pll2. Further, the
name used in the RM is video_pll. So, let's rename "video_pll1" to
"video_pll" to be consistent with the RM and avoid misunderstandings.
The IMX8MN_VIDEO_PLL1* constants have not been removed to ensure
backward compatibility of the patch.
No functional changes intended.
Fixes: e3a7483537b5b ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-4-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no occurrence of the hdmi oscillator in the reference manual
(document IMX8MNRM Rev 2, 07/2022). Further, if we consider the indexes
76-81 and 134 of the "Clock Root" table of chapter 5 of the RM, there is
no entry for the source select bits 101b, which is the setting referenced
by "osc_hdmi".
Fix by renaming "osc_hdmi" with "dummy", a clock which has already been
used for missing source select bits.
Tested on the BSH SystemMaster (SMM) S2 board.
Fixes: e3a7483537b5b ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-3-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The IMX8MN platform does not have any video processing unit (VPU), and
indeed in the reference manual (document IMX8MNRM Rev 2, 07/2022) there
is no occurrence of its pll. From an analysis of the code and the RM
itself, I think vpu pll is used instead of m7 alternate pll, probably
for copy and paste of code taken from modules of similar architectures.
As an example for all, if we consider the second row of the "Clock Root"
table of chapter 5 (Clocks and Power Management) of the RM:
but in the source code, the imx8mn_m7_sels clocks list contains vpu_pll
for the source select bits 011b.
So, let's rename "vpu_pll" to "m7_alt_pll" to be consistent with the RM.
The IMX8MN_VPU_* constants have not been removed to ensure backward
compatibility of the patch.
No functional changes intended.
Fixes: e3a7483537b5b ("clk: imx: Add support for i.MX8MN clock driver") Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Acked-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221117113637.1978703-2-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The mt9p031_init_cfg() already calls __mt9p031_get_pad_crop(), which
correctly calls v4l2_subdev_get_try_crop() on V4L2_SUBDEV_FORMAT_TRY
or returns &mt9p031->crop on V4L2_SUBDEV_FORMAT_ACTIVE. No need to
call v4l2_subdev_get_try_crop() in mt9p031_init_cfg() again in case
of both V4L2_SUBDEV_FORMAT_TRY and V4L2_SUBDEV_FORMAT_ACTIVE.
This also fixes a splat generated by this call since commit 72c10bb6f9c16 ("media: v4l: subdev: Fail graciously when getting try data for NULL state")
because v4l2_subdev_get_try_crop() is called with sd_state = NULL
in mt9p031_init_cfg().
Fixes: b99932a49f578 ("media: mt9p031: Move open subdev op init code into init_cfg") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 624517f9b805 ("media: imx: imx7-media-csi: Use dual sampling for
YUV 1X16") set BIT_MIPI_DOUBLE_CMPNT in the CR18 register for 16-bit YUV
formats in imx7_csi_configure(). The CR18 register is always updated
with read-modify-write cycles, so if a 16-bit YUV format is selected,
the bit will stay set forever, even if the format is changed. Fix it by
clearing the bit at the beginning of the imx7_csi_configure() function.
While at it, swap two of the bits being cleared to match the MSB to LSB
order. This doesn't cause any functional change.
Fixes: 624517f9b805 ("media: imx: imx7-media-csi: Use dual sampling for YUV 1X16") Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Paul Elder <paul.elder@ideasonboard.com> Acked-by: Rui Miguel Silva <rmfrfs@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function send_packet() has a race condition as follows:
func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}
func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed
mutex_unlock()
}
When the mutex is unlocked and the function send_packet() waits for the
call to complete, vfd_write() can start another call, which leads to the
"URB submitted while active" warning in usb_submit_urb().
Fix this by removing the mutex_unlock() call in send_packet() and using
mutex_lock_interruptible().
In vimc_init(), when platform_driver_register(&vimc_pdrv) fails,
platform_driver_unregister(&vimc_pdrv) is wrongly called rather than
platform_device_unregister(&vimc_pdev), which causes kernel warning:
SND_SOC_QCOM_COMMON depends on SOUNDWIRE for some symbols but this
is not explicitly specified using Kconfig depends. On the other hand
SND_SOC_QCOM_COMMON is also directly selected by the sound card
Kconfigs, this could result in various combinations and some symbols
ending up in modules and soundcard that uses those symbols as in-build
driver.
Fix these issues by explicitly specifying the dependencies of
SND_SOC_QCOM_COMMON and also use imply a to select SND_SOC_QCOM_COMMON
so that the symbol is selected based on its dependencies.
Also remove dummy stubs in common.c around CONFIG_SOUNDWIRE
Fixes: a926386029a5 ("ASoC: qcom: sm8250: move some code to common") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221124140351.407506-1-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A submitter workqueue is dynamically allocated by init_submitter()
called by drbd_create_device(), we should destroy it when this
device is not needed or destroyed.
Fixes: cf2386260a19 ("drbd: prepare to queue write requests on a submit worker") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lore.kernel.org/r/20221124015817.2729789-3-bobo.shaobowang@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This revert 146dec340e91 ("drbd: poison free'd device, resource and
connection structs"), add memset is odd here for debugging, there are
some methods to accurately show what happened, such as kdump.
del_mtd_device() will call of_node_put() to mtd_get_of_node(mtd), which
is mtd->dev.of_node. However, memset(&mtd->dev, 0) is called before
of_node_put(). As the result, of_node_put() won't do anything in
del_mtd_device(), and causes the refcount leak.
Before this change when a bond in mode 2 lost link, all of its slaves
lost link, the bonding device would never recover even after the
expiration of updelay. This change removes the updelay when the bond
currently has no usable links. Conforming to bonding.txt section 13.1
paragraph 4.
Fixes: 7c463d776017 ("bonding: ignore updelay param when there is no active slave") Signed-off-by: Jonathan Toppins <jtoppins@redhat.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri reports broken test_progs after recent commit 8cfaaa65524d
("selftests/bpf: Make sure zero-len skbs aren't redirectable").
Apparently we don't remount debugfs when we switch back networking namespace.
Let's explicitly mount /sys/kernel/debug.
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak.
Fixes: 79dedd8cf74d ("drm/amdgpu: put the audio codec into suspend state before gpu reset V3") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If clk_register() fails, @pll->rate_table may have allocated memory by
kmemdup(), so it needs to be freed, otherwise will cause memory leak
issue, this patch fixes it.
Fixes: 3961a42600c7 ("clk: rockchip: add clock type for pll clocks and pll used on rk3066") Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Link: https://lore.kernel.org/r/20221123091201.199819-1-xiujianfeng@huawei.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use kfree_const() to free supply_name conditionally in create_regulator()
as supply_name may be allocated from kmalloc() or directly from .rodata
section.
Fixes: 494d2aba3c15 ("regulator: push allocations in create_regulator() outside of lock") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Link: https://lore.kernel.org/r/20221123034616.3609537-1-bobo.shaobowang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/seq/seq_clientmgr.c:509:22
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_seq_deliver_single_event.constprop.21+0x191/0x2f0
snd_seq_deliver_event+0x1a2/0x350
snd_seq_kernel_client_dispatch+0x8b/0xb0
snd_seq_client_notify_subscription+0x72/0xa0
snd_seq_ioctl_subscribe_port+0x128/0x160
snd_seq_kernel_client_ctl+0xce/0xf0
snd_seq_oss_create_client+0x109/0x15b
alsa_seq_oss_init+0x11c/0x1aa
do_one_initcall+0x80/0x440
kernel_init_freeable+0x370/0x3c3
kernel_init+0x1b/0x190
ret_from_fork+0x1f/0x30
</TASK>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/pcm_native.c:2676:21
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_pcm_open_substream+0x9f0/0xa90
snd_pcm_oss_open.part.26+0x313/0x670
snd_pcm_oss_open+0x30/0x40
soundcore_open+0x18b/0x2e0
chrdev_open+0xe2/0x270
do_dentry_open+0x2f7/0x620
path_openat+0xd66/0xe70
do_filp_open+0xe3/0x170
do_sys_openat2+0x357/0x4a0
do_sys_open+0x87/0xd0
do_syscall_64+0x34/0x80
Since for_each_available_child_of_node() will increase the refcount of
node, we need to call of_node_put() manually when breaking out of the
iteration.
This is no bugfix (so no Fixes: tag is necessary) as it is
taken care of in hid_sensor_custom_add_attributes().
The motivation for this patch is that:
hid_sensor_custom_field.attr_name and
hid_sensor_custom_field.attrs
has the size of HID_CUSTOM_TOTAL_ATTRS and used in same context.
We compare against HID_CUSTOM_TOTAL_ATTRS when
looping through hid_custom_attrs.
We will silent the smatch error:
hid_sensor_custom_add_attributes() error: buffer overflow
'hid_custom_attrs' 8 <= 10
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per update Reference Mannual, correct the enet clock parent to
wakeup_axi_root.
Fixes: a3625fe0861e ("clk: imx: add i.MX93 clk") Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221028095211.2598312-3-peng.fan@oss.nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The anatop base is not unmapped during error handling path, fix it.
Fixes: a3625fe0861e ("clk: imx: add i.MX93 clk") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20221028095211.2598312-2-peng.fan@oss.nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
HID-RMI is special in the sense that it does not carry HID events
directly, but rather uses HID protocol as a wrapper/transport for RMI
protocol. Therefore we should not assume that all data coming from the
device via interrupt is associated with user activity and report wakeup
event indiscriminately, but rather let HID-RMI do that when appropriate.
HID-RMI devices tag responses to the commands issued by the host as
RMI_READ_DATA_REPORT_ID whereas motion and other input events from the
device are tagged as RMI_ATTN_REPORT_ID. Change hid-rmi to report wakeup
events when receiving the latter packets. This allows ChromeOS to
accurately identify wakeup source and make correct decision on the mode
of the resume the system should take ("dark" where the display stays off
vs normal one).
projects / kernel.git / log