The firmware revision can change on after a reset so copy the most
recent info each time instead of just the first time, otherwise the
sysfs firmware_rev entry may contain stale data.
Reported-by: Jeff Lien <jeff.lien@wdc.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Chao Leng <lengchao@huawei.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rtw_init_cmd_priv(), if `pcmdpriv->rsp_allocated_buf` is allocated
in failure, then `pcmdpriv->cmd_allocated_buf` will be not properly
released. Besides, considering there are only two error paths and the
first one can directly return, so we do not need implicitly jump to the
`exit` tag to execute the error handler.
So this patch added `kfree(pcmdpriv->cmd_allocated_buf);` on the error
path to release the resource and simplified the return logic of
rtw_init_cmd_priv(). As there is no proper device to test with, no runtime
testing was performed.
But the commit affects not only "Samsung Fit Flash" but also other usb
storages that use the same controller and causes severe performance
regression.
# hdparm -t /dev/sda (without the quirk)
Timing buffered disk reads: 622 MB in 3.01 seconds = 206.66 MB/sec
# hdparm -t /dev/sda (with the quirk)
Timing buffered disk reads: 220 MB in 3.00 seconds = 73.32 MB/sec
The commit author mentioned that "Issue was reproduced after device has
bad block", so this quirk should be applied when we have the timeout
issue with a device that has bad blocks.
We revert the commit so that we apply this quirk by adding kernel
paramters using a bootloader or other ways when we really need it,
without the performance regression with devices that don't have the
issue.
The usb function device call musb_gadget_queue() adds the passed
request to musb_ep::req_list,If the (request->length > musb_ep->packet_sz)
and (is_buffer_mapped(req) return false),the rxstate() will copy all data
in fifo to request->buf which may cause request->buf out of bounds.
Fix it by add the length check :
fifocnt = min_t(unsigned, request->length - request->actual, fifocnt);
xhci_alloc_stream_info() allocates stream context array for stream_info
->stream_ctx_array with xhci_alloc_stream_ctx(). When some error occurs,
stream_info->stream_ctx_array is not released, which will lead to a
memory leak.
We can fix it by releasing the stream_info->stream_ctx_array with
xhci_free_stream_ctx() on the error path to avoid the potential memory
leak.
A complicated deadlock exists when using the journal and an elevated
group_thrtead_cnt. It was found with loop devices, but its not clear
whether it can be seen with real disks. The deadlock can occur simply
by writing data with an fio script.
When the deadlock occurs, multiple threads will hang in different ways:
1) The group threads will hang in the blk-wbt code with bios waiting to
be submitted to the block layer:
However, before hanging, the MD_SB_CHANGE_PENDING flag will be
set for sb_flags in r5l_write_super_and_discard_space(). This
flag will never be cleared because the submit_bio() call never
returns.
3) Due to the MD_SB_CHANGE_PENDING flag being set, handle_stripe()
will do no processing on any pending stripes and re-set
STRIPE_HANDLE. This will cause the raid5d thread to enter an
infinite loop, constantly trying to handle the same stripes
stuck in the queue.
The raid5d thread has a blk_plug that holds a number of bios
that are also stuck waiting seeing the thread is in a loop
that never schedules. These bios have been accounted for by
blk-wbt thus preventing the other threads above from
continuing when they try to submit bios. --Deadlock.
To fix this, add the same wait_event() that is used in raid5_do_work()
to raid5d() such that if MD_SB_CHANGE_PENDING is set, the thread will
schedule and wait until the flag is cleared. The schedule action will
flush the plug which will allow the r5l_reclaim thread to continue,
thus preventing the deadlock.
However, md_check_recovery() calls can also clear MD_SB_CHANGE_PENDING
from the same thread and can thus deadlock if the thread is put to
sleep. So avoid waiting if md_check_recovery() is being called in the
loop.
It's not clear when the deadlock was introduced, but the similar
wait_event() call in raid5_do_work() was added in 2017 by this
commit:
1c07006b6d0a ("md/raid5: simplfy delaying of writes while metadata
is updated.")
new_value = kmemdup(data, device->report_size, GFP_ATOMIC);
if (!new_value)
return -ENOMEM;
report = &device->cbuf[device->cbuf_end];
/* passing NULL is safe */
kfree(report->value);
...
The registered report is stored in the struct roccat_device member
"struct roccat_report cbuf[ROCCAT_CBUF_SIZE];".
If more reports are received than the "ROCCAT_CBUF_SIZE" value,
kfree() the saved report from cbuf[0] and allocates a new reprot.
Since there is no lock when this kfree() is performed,
kfree() can be performed even while reading the saved report.
report = &device->cbuf[reader->cbuf_start];
/*
* If report is larger than requested amount of data, rest of report
* is lost!
*/
len = device->report_size > count ? count : device->report_size;
The roccat_read() function receives the device->cbuf report and
delivers it to the user through copy_to_user().
If the N+ROCCAT_CBUF_SIZE th report is received while copying of
the Nth report->value is in progress, the pointer that copy_to_user()
is working on is kfree()ed and UAF read may occur. (race condition)
Since the device node of this driver does not set separate permissions,
this is not a security vulnerability, but because it is used for
requesting screen display of profile or dpi settings,
a user using the roccat device can apply udev to this device node or
There is a possibility to use it by giving.
Inside set_at_max_writeback_rate() the calculation in following if()
check is wrong,
if (atomic_inc_return(&c->idle_counter) <
atomic_read(&c->attached_dev_nr) * 6)
Because each attached backing device has its own writeback thread
running and increasing c->idle_counter, the counter increates much
faster than expected. The correct calculation should be,
(counter / dev_nr) < dev_nr * 6
which equals to,
counter < dev_nr * dev_nr * 6
This patch fixes the above mistake with correct calculation, and helper
routine idle_counter_exceeded() is added to make code be more clear.
Reported-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Signed-off-by: Coly Li <colyli@suse.de> Acked-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Link: https://lore.kernel.org/r/20220919161647.81238-6-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical
from the further AHCI-platform initialization point of view since
exceeding the ports upper limit will cause allocating more resources than
will be used afterwards. But detecting too many child DT-nodes doesn't
seem right since it's very unlikely to have it on an ordinary platform. In
accordance with the AHCI specification there can't be more than 32 ports
implemented at least due to having the CAP.NP field of 5 bits wide and the
PI register of dword size. Thus if such situation is found the DTB must
have been corrupted and the data read from it shouldn't be reliable. Let's
consider that as an erroneous situation and halt further resources
allocation.
Note it's logically more correct to have the nports set only after the
initialization value is checked for being sane. So while at it let's make
sure nports is assigned with a correct value.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function device_init_td0_ring, memory is allocated for member
td_info of priv->apTD0Rings[i], with i increasing from 0. In case of
allocation failure, the memory is freed in reversed order, with i
decreasing to 0. However, the case i=0 is left out and thus memory is
leaked.
Modify the memory freeing loop to include the case i=0.
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Signed-off-by: Nam Cao <namcaov@gmail.com> Link: https://lore.kernel.org/r/20220909141338.19343-1-namcaov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ADP5061_CHG_STATUS_1_CHG_STATUS is masked with 0x07, which means a length
of 8, but adp5061_chg_type array size is 4, may end up reading 4 elements
beyond the end of the adp5061_chg_type[] array.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported hung task [1]. The following program is a simplified
version of the reproducer:
int main(void)
{
int sv[2], fd;
if (socketpair(AF_UNIX, SOCK_STREAM, 0, sv) < 0)
return 1;
if ((fd = open("/dev/nbd0", 0)) < 0)
return 1;
if (ioctl(fd, NBD_SET_SIZE_BLOCKS, 0x81) < 0)
return 1;
if (ioctl(fd, NBD_SET_SOCK, sv[0]) < 0)
return 1;
if (ioctl(fd, NBD_DO_IT) < 0)
return 1;
return 0;
}
When signal interrupt nbd_start_device_ioctl() waiting the condition
atomic_read(&config->recv_threads) == 0, the task can hung because it
waits the completion of the inflight IOs.
This patch fixes the issue by clearing queue, not just shutdown, when
signal interrupt nbd_start_device_ioctl().
The original code will "goto out_disable_device" and call
pci_disable_device() if pci_enable_device() fails. The kernel will generate
a warning message like "3w-9xxx 0000:00:05.0: disabling already-disabled
device".
We shouldn't disable a device that failed to be enabled. A simple return is
fine.
Link: https://lore.kernel.org/r/20220829110115.38789-1-fantasquex@gmail.com Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
When the driver calls cx88_risc_buffer() to prepare the buffer, the
function call may fail, resulting in a empty buffer and null-ptr-deref
later in buffer_queue().
"BUG: KASAN: stack-out-of-bounds in strncpy+0x30/0x68"
Linux-ATF interface is using 16 bytes of SMC payload. In case clock name is
longer than 15 bytes, string terminated NULL character will not be received
by Linux. Add explicit NULL character at last byte to fix issues when clock
name is longer.
This fixes below bug reported by KASAN:
==================================================================
BUG: KASAN: stack-out-of-bounds in strncpy+0x30/0x68
Read of size 1 at addr ffff0008c89a7410 by task swapper/0/1
The first scrub reports the super error correctly:
scrub done for f3289218-abd3-41ac-a630-202f766c0859
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
But the second read-only scrub still reports the same super error:
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
[CAUSE]
The comments already shows that super block can be easily fixed by
committing a transaction:
/*
* If we find an error in a super block, we just report it.
* They will get written with the next transaction commit
* anyway
*/
But the truth is, such assumption is not always true, and since scrub
should try to repair every error it found (except for read-only scrub),
we should really actively commit a transaction to fix this.
[FIX]
Just commit a transaction if we found any super block errors, after
everything else is done.
We cannot do this just after scrub_supers(), as
btrfs_commit_transaction() will try to pause and wait for the running
scrub, thus we can not call it with scrub_lock hold.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1 - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
The Snapdragon 670 has the same quirk as Snapdragon 845 (needing to
restore the dll config). Add a compatible string check to detect the need
for this.
On a MSI S270 with Fedora 37 x86_64 / systemd-251.4 the module does not
properly autoload.
This is likely caused by issues with how systemd-udevd handles the single
quote char (') which is part of the sys_vendor / chassis_vendor strings
on this laptop. As a workaround remove the single quote char + everything
behind it from the sys_vendor + chassis_vendor matches. This fixes
the module not autoloading.
This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.
Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.
The definition of MIN_I64 in bw_fixed.c can cause gcc to whinge about
integer overflow, because it is treated as a positive value, which is
then negated. The temporary positive value is not necessarily
representable.
This causes the following warning:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dml/calcs/bw_fixed.c:30:19:
warning: integer overflow in expression ‘-9223372036854775808’ of type
‘long long int’ results in ‘-9223372036854775808’ [-Woverflow]
30 | (int64_t)(-(1LL << 63))
| ^
Writing out (-MAX_I64 - 1) works instead.
Signed-off-by: David Gow <davidgow@google.com> Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The strlen() function returns a size_t which is an unsigned int on 32-bit
arches and an unsigned long on 64-bit arches. But in the drm_copy_field()
function, the strlen() return value is assigned to an 'int len' variable.
Later, the len variable is passed as copy_from_user() third argument that
is an unsigned long parameter as well.
In theory, this can lead to an integer overflow via type conversion. Since
the assignment happens to a signed int lvalue instead of a size_t lvalue.
In practice though, that's unlikely since the values copied are set by DRM
drivers and not controlled by userspace. But using a size_t for len is the
correct thing to do anyways.
nouveau_bo_alloc() allocates a memory chunk for "nvbo" with kzalloc().
When some error occurs, "nvbo" should be released. But when
WARN_ON(pi < 0)) equals true, the function return ERR_PTR without
releasing the "nvbo", which will lead to a memory leak.
We should release the "nvbo" with kfree() if WARN_ON(pi < 0)) equals true.
While waiting for memory in thread1, the socket is released with its wait
queue because thread2 has closed it. This caused by tcp_bpf_send_verdict
didn't increase the f_count of psock->sk_redir->sk_socket->file in thread1.
We should check if SOCK_DEAD flag is set on wakeup in sk_stream_wait_memory
before accessing the wait queue.
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/bpf/20220823133755.314697-2-liujian56@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of using the default value 33 (pci), set US_CYC_CNT init based
on Programming guide:
If available, set chipset bus clock with fallback to cpu clock/3.
syzbot is reporting cancel_delayed_work() without INIT_DELAYED_WORK() at
l2cap_chan_del() [1], for CONF_NOT_COMPLETE flag (which meant to prevent
l2cap_chan_del() from calling cancel_delayed_work()) is cleared by timer
which fires before l2cap_chan_del() is called by closing file descriptor
created by socket(AF_BLUETOOTH, SOCK_STREAM, BTPROTO_L2CAP).
l2cap_bredr_sig_cmd(L2CAP_CONF_REQ) and l2cap_bredr_sig_cmd(L2CAP_CONF_RSP)
are calling l2cap_ertm_init(chan), and they call l2cap_chan_ready() (which
clears CONF_NOT_COMPLETE flag) only when l2cap_ertm_init(chan) succeeded.
l2cap_sock_init() does not call l2cap_ertm_init(chan), and it instead sets
CONF_NOT_COMPLETE flag by calling l2cap_chan_set_defaults(). However, when
connect() is requested, "command 0x0409 tx timeout" happens after 2 seconds
from connect() request, and CONF_NOT_COMPLETE flag is cleared after 4
seconds from connect() request, for l2cap_conn_start() from
l2cap_info_timeout() callback scheduled by
Fix this problem by initializing delayed works used by L2CAP_MODE_ERTM
mode as soon as l2cap_chan_create() allocates a channel, like I did in
commit 08c674fe5fb785d8 ("Bluetooth: initialize skb_queue_head at
l2cap_chan_create()").
Link: https://syzkaller.appspot.com/bug?extid=83672956c7aa6af698b3 Reported-by: syzbot <syzbot+83672956c7aa6af698b3@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if ipcomp_alloc_scratches() fails to allocate memory
ipcomp_scratches holds obsolete address. So when we try to free the
percpu scratches using ipcomp_free_scratches() it tries to vfree non
existent vm area. Described below:
static void * __percpu *ipcomp_alloc_scratches(void)
{
...
scratches = alloc_percpu(void *);
if (!scratches)
return NULL;
ipcomp_scratches does not know about this allocation failure.
Therefore holding the old obsolete address.
...
}
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
tcp_md5sig_pool_populated can be read while another thread
changes its value.
The race has no consequence because allocations
are protected with tcp_md5sig_mutex.
This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently queue_userspace_packet will call kfree_skb for all frames,
whether or not an error occurred. This can result in a single dropped
frame being reported as multiple drops in dropwatch. This functions
caller may also call kfree_skb in case of an error. This patch will
consume the skbs instead and allow caller's to use kfree_skb.
Frames sent to userspace can be reported as dropped in
ovs_dp_process_packet, however, if they are dropped in the netlink code
then netlink_attachskb will report the same frame as dropped.
This patch checks for error codes which indicate that the frame has
already been freed.
When bpftool is linked against libcap, the library runs a "constructor"
function to compute the number of capabilities of the running kernel
[0], at the beginning of the execution of the program. As part of this,
it performs multiple calls to prctl(). Some of these may fail, and set
errno to a non-zero value:
# strace -e prctl ./bpftool version
prctl(PR_CAPBSET_READ, CAP_MAC_OVERRIDE) = 1
prctl(PR_CAPBSET_READ, 0x30 /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, CAP_CHECKPOINT_RESTORE) = 1
prctl(PR_CAPBSET_READ, 0x2c /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, 0x2a /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, 0x29 /* CAP_??? */) = -1 EINVAL (Invalid argument)
** fprintf added at the top of main(): we have errno == 1
./bpftool v7.0.0
using libbpf v1.0
features: libbfd, libbpf_strict, skeletons
+++ exited with 0 +++
This has been addressed in libcap 2.63 [1], but until this version is
available everywhere, we can fix it on bpftool side.
Let's clean errno at the beginning of the main() function, to make sure
that these checks do not interfere with the batch mode, where we error
out if errno is set after a bpftool command.
This was discussed with Chuck as part of this patch set. Returning
nfserr_resource was decided to not be the best error message here, and
he suggested changing to nfserr_serverfault instead.
When CPU 0 is offline and intel_powerclamp is used to inject
idle, it generates kernel BUG:
BUG: using smp_processor_id() in preemptible [00000000] code: bash/15687
caller is debug_smp_processor_id+0x17/0x20
CPU: 4 PID: 15687 Comm: bash Not tainted 5.19.0-rc7+ #57
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
check_preemption_disabled+0xdd/0xe0
debug_smp_processor_id+0x17/0x20
powerclamp_set_cur_state+0x7f/0xf9 [intel_powerclamp]
...
...
Here CPU 0 is the control CPU by default and changed to the current CPU,
if CPU 0 offlined. This check has to be performed under cpus_read_lock(),
hence the above warning.
Use get_cpu() instead of smp_processor_id() to avoid this BUG.
When value < time_unit, the parameter of ilog2() will be zero and
the return value is -1. u64(-1) is too large for shift exponent
and then will trigger shift-out-of-bounds:
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
Call Trace:
rapl_compute_time_window_core
rapl_write_data_raw
set_time_window
store_constraint_time_window_us
Signed-off-by: Chao Qin <chao.qin@intel.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang is especially sensitive about argument type matching when using
__overloaded functions (like memcmp(), etc). Help it see that function
pointers are just "void *". Avoids this error:
arch/mips/bcm47xx/prom.c:89:8: error: no matching function for call to 'memcmp'
if (!memcmp(prom_init, prom_init + mem, 32))
^~~~~~
include/linux/string.h:156:12: note: candidate function not viable: no known conversion from 'void (void)' to 'const void *' for 1st argument extern int memcmp(const void *,const void *,__kernel_size_t);
Toshiba Satellite Z830 needs the quirk video_disable_backlight_sysfs_if
for proper backlight control after suspend/resume cycles.
Toshiba Portege Z830 is simply the same laptop rebranded for certain
markets (I looked through the manual to other language sections to confirm
this) and thus also needs this quirk.
Thanks to Hans de Goede for suggesting this fix.
Link: https://www.spinics.net/lists/platform-driver-x86/msg34394.html Suggested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Arvid Norlander <lkml@vorpal.se> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Arvid Norlander <lkml@vorpal.se> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The following scenarios exist.
process A: process B:
->f2fs_drop_extent_tree ->f2fs_update_extent_cache_range
->f2fs_update_extent_tree_range
->write_lock
->set_inode_flag
->is_inode_flag_set
->__free_extent_tree // Shouldn't
// have been
// cleaned up
// here
->write_lock
In this case, the "FI_NO_EXTENT" flag is set between
f2fs_update_extent_tree_range and is_inode_flag_set
by other process. it leads to clearing the whole exten
tree which should not have happened. And we fix it by
move the setting it to the range of write_lock.
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "ntohl(ucode->code_length) * 2" multiplication can have an
integer overflow.
Fixes: b4451ad6d9e1 ("crypto: cavium - Add Support for Octeon-tx CPT Engine") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving some signal, GNU Make automatically deletes the target if
it has already been changed by the interrupted recipe.
If the target is possibly incomplete due to interruption, it must be
deleted so that it will be remade from scratch on the next run of make.
Otherwise, the target would remain corrupted permanently because its
timestamp had already been updated.
Thanks to this behavior of Make, you can stop the build any time by
pressing Ctrl-C, and just run 'make' to resume it.
Kbuild also relies on this feature, but it is equivalently important
for any build systems that make decisions based on timestamps (if you
want to support Ctrl-C reliably).
However, this does not always work as claimed; Make immediately dies
with Ctrl-C if its stderr goes into a pipe.
$ make 2>&1 | cat # hit Ctrl-C
echo hello > foo
sleep 3
^C$ # 'foo' is often left-over
The reason is because SIGINT is sent to the entire process group.
In this example, SIGINT kills 'cat', and 'make' writes the message to
the closed pipe, then dies with SIGPIPE before cleaning the target.
A typical bad scenario (as reported by [1], [2]) is to save build log
by using the 'tee' command:
$ make 2>&1 | tee log
This can be problematic for any build systems based on Make, so I hope
it will be fixed in GNU Make. The maintainer of GNU Make stated this is
a long-standing issue and difficult to fix [3]. It has not been fixed
yet as of writing.
So, we cannot rely on Make cleaning the target. We can do it by
ourselves, in signal traps.
As far as I understand, Make takes care of SIGHUP, SIGINT, SIGQUIT, and
SITERM for the target removal. I added the traps for them, and also for
SIGPIPE just in case cmd_* rule prints something to stdout or stderr
(but I did not observe an actual case where SIGPIPE was triggered).
[Note 1]
The trap handler might be worth explaining.
rm -f $@; trap - $(sig); kill -s $(sig) $$
This lets the shell kill itself by the signal it caught, so the parent
process can tell the child has exited on the signal. Generally, this is
a proper manner for handling signals, in case the calling program (like
Bash) may monitor WIFSIGNALED() and WTERMSIG() for WCE although this may
not be a big deal here because GNU Make handles SIGHUP, SIGINT, SIGQUIT
in WUE and SIGTERM in IUE.
IUE - Immediate Unconditional Exit
WUE - Wait and Unconditional Exit
WCE - Wait and Cooperative Exit
For details, see "Proper handling of SIGINT/SIGQUIT" [4].
[Note 2]
Reverting 81df09f9bf80 ("kbuild: let fixdep directly write to .*.cmd
files") would directly address [1], but it only saves if_changed_dep.
As reported in [2], all commands that use redirection can potentially
leave an empty (i.e. broken) target.
[Note 3]
Another (even safer) approach might be to always write to a temporary
file, and rename it to $@ at the end of the recipe.
<command> > $(tmp-target)
mv $(tmp-target) $@
It would require a lot of Makefile changes, and result in ugly code,
so I did not take it.
[Note 4]
A little more thoughts about a pattern rule with multiple targets (or
a grouped target).
%.x %.y: %.z
<recipe>
When interrupted, GNU Make deletes both %.x and %.y, while this solution
only deletes $@. Probably, this is not a big deal. The next run of make
will execute the rule again to create $@ along with the other files.
IOMMU_IOVA is intended to be an optional library for users to select as
and when they desire. Since it can be a module now, this means that
built-in code which has chosen not to select it should not fail to link
if it happens to have selected as a module by someone else. Replace
IS_ENABLED() with IS_REACHABLE() to do the right thing.
CC: Thierry Reding <thierry.reding@gmail.com> Reported-by: John Garry <john.garry@huawei.com> Fixes: 82ab2a1e416b ("iommu: Make the iova library a module") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/548c2f683ca379aface59639a8f0cccc3a1ac050.1663069227.git.robin.murphy@arm.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
__dma_async_device_channel_unregister called while 2 clients hold a reference
WARNING: CPU: 15 PID: 1 at drivers/dma/dmaengine.c:1110 __dma_async_device_channel_unregister+0xb7/0xc0
Call dma_release_channel for occupied channles before dma_async_device_unregister.
Fixes: 7155c975a3fe ("crypto: ccp - ccp_dmaengine_unregister release dma channels") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Koba Ko <koba.ko@canonical.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Changes from v1:
* removed the default implementation from set_pub_key: it is assumed that
an implementation must always have this callback defined as there are
no use case for an algorithm, which doesn't need a public key
Many akcipher implementations (like ECDSA) support only signature
verifications, so they don't have all callbacks defined.
Commit 0b8e6d8f3602 ("crypto: akcipher - default implementations for
request callbacks") introduced default callbacks for sign/verify
operations, which just return an error code.
However, these are not enough, because before calling sign the caller would
likely call set_priv_key first on the instantiated transform (as the
in-kernel testmgr does). This function does not have a default stub, so the
kernel crashes, when trying to set a private key on an akcipher, which
doesn't support signature generation.
I've noticed this, when trying to add a KAT vector for ECDSA signature to
the testmgr.
With this patch the testmgr returns an error in dmesg (as it should)
instead of crashing the kernel NULL ptr dereference.
1) The "len" variable needs to be checked before the very first write.
Otherwise if omap2_iommu_dump_ctx() with "bytes" less than 32 it is a
buffer overflow.
2) The snprintf() function returns the number of bytes that *would* have
been copied if there were enough space. But we want to know the
number of bytes which were *actually* copied so use scnprintf()
instead.
Previously, update_tasks_cpumask() is not supposed to be called with
top cpuset. With cpuset partition that takes CPUs away from the top
cpuset, adjusting the cpus_mask of the tasks in the top cpuset is
necessary. Percpu kthreads, however, are ignored.
Fixes: 28d4fbb42d1d ("cpuset: Add new v2 cpuset.sched.partition flag") Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 75d5a18fecc4 ("powerpc/e500v2: Add Power ISA properties to comply
with ePAPR 1.1") introduced new include file e500v2_power_isa.dtsi and
should have used it for all e500v2 platforms. But apparently it was used
also for e500v1 platforms mpc8540, mpc8541, mpc8555 and mpc8560.
e500v1 cores compared to e500v2 do not support double precision floating
point SPE instructions. Hence power-isa-sp.fd should not be set on e500v1
platforms, which is in e500v2_power_isa.dtsi include file.
Fix this issue by introducing a new e500v1_power_isa.dtsi include file and
use it in all e500v1 device tree files.
Fixes: 75d5a18fecc4 ("powerpc/e500v2: Add Power ISA properties to comply with ePAPR 1.1") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220902212103.22534-1-pali@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Big-endian GENERIC_CPU supports 970, but builds with -mcpu=power5.
POWER5 is ISA v2.02 whereas 970 is v2.01 plus Altivec. 2.02 added
the popcntb instruction which a compiler might use.
In fsl_setup_msi_irqs(), use of_node_put() to drop the reference
returned by of_parse_phandle().
Fixes: 2399f7b2cc58a ("powerpc/fsl_msi: add support for the fsl, msi property in PCI nodes") Co-authored-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220704145233.278539-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with a recent version of clang, there are a couple of
errors around the call to module_init():
arch/powerpc/math-emu/math_efp.c:927:1: error: type specifier missing, defaults to 'int'; ISO C99 and later do not support implicit int [-Wimplicit-int]
module_init(spe_mathemu_init);
^
int
arch/powerpc/math-emu/math_efp.c:927:13: error: a parameter list without types is only allowed in a function definition
module_init(spe_mathemu_init);
^
2 errors generated.
module_init() is a macro, which is not getting expanded because module.h
is not included in this file. Add the include so that the macro can
expand properly, clearing up the build failure.
pm_runtime_get_sync() will increment pm usage counter.
Forgetting to putting operation will result in reference leak.
Add missing pm_runtime_put_sync in some error paths.
Fixes: 8a2d7a83c0bc ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220602030838.52057-1-linmq006@gmail.com Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value of bcm2835_clock_rate_from_divisor is always unsigned
and also all caller expect this. So fix the declaration accordingly.
Fixes: 87307b6bea6a ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220904141037.38816-1-stefan.wahren@i2se.com Reviewed-by: Ivan T. Ivanov <iivanov@suse.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Correct the way that duplicate PPID mappings are handled for PMIC
arbiter v5. The final APID mapped to a given PPID should be the
one which has write owner = APPS EE, if it exists, or if not
that, then the first APID mapped to the PPID, if it exists.
User reports observing timer event report channel halted but no error
observed in CHANERR register. The driver finished self-test and released
channel resources. Debug shows that __cleanup() can call
mod_timer() after the timer has been deleted and thus resurrect the
timer. While harmless, it causes suprious error message to be emitted.
Use mod_timer_pending() call to prevent deleted timer from being
resurrected.
The mx25_tsadc_remove() function assumes all non-zero returns are success
but the platform_get_irq() function returns negative on error and
positive non-zero values on success. It never returns zero, but if it
did then treat that as a success.
Fixes: f702968974ac ("mfd: fsl-imx25: Clean up irq settings during removal") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Martin Kaiser <martin@kaiser.cx> Signed-off-by: Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/YvTfkbVQWYKMKS/t@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
In lp8788_irq_init(), if an error occurs after a successful
irq_domain_add_linear() call, it must be undone by a corresponding
irq_domain_remove() call.
irq_domain_remove() should also be called in lp8788_irq_exit() for the same
reason.
If devm_of_platform_populate() fails, some resources need to be
released.
Introduce a mx25_tsadc_unset_irq() function that undoes
mx25_tsadc_setup_irq() and call it both from the new error handling path
of the probe and in the remove function.
The commit in Fixes: has added a pwm_add_table() call in the probe() and
a pwm_remove_table() call in the remove(), but forget to update the error
handling path of the probe.
Add the missing pwm_remove_table() call.
Fixes: bd81715d4c39 ("mfd: intel_soc_pmic_core: ADD PWM lookup table for CRC PMIC based PWM") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20220801114211.36267-1-andriy.shevchenko@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If allocation fails, the ida_simple_get() will return error number.
So master->idx could be error number and be used in dev_set_name().
Therefore, it should be better to check it and return error if fails,
like the ida_simple_get() in __fsi_get_new_minor().
Fixes: 95b720049fea ("drivers/fsi: Add fsi master definition") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reviewed-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20220111073411.614138-1-jiasheng@iscas.ac.cn Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When executing SMP task failed, the smp_execute_task_sg() calls del_timer()
to delete "slow_task->timer". However, if the timer handler
sas_task_internal_timedout() is running, the del_timer() in
smp_execute_task_sg() will not stop it and a UAF will happen. The process
is shown below:
Fix by calling del_timer_sync() in smp_execute_task_sg(), which makes sure
the timer handler have finished before the "task->slow_task" is
deallocated.
Link: https://lore.kernel.org/r/20220920144213.10536-1-duoming@zju.edu.cn Fixes: 4cb7d5b2948d ("[SCSI] aic94xx: new driver") Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 59a9170a436f ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Since commit 1e74ca0fb2a4 ("serial: core: Fix initializing and restoring
termios speed") termios speed is available also in struct console.
So properly restore also c_ispeed and c_ospeed members after suspend to fix
restoring termios speed which is not represented by Bnnn constant.
Fixes: 29061f786f08 ("serial: 8250: Use canary to restart console after suspend") Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20220924104324.4035-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the gsmi driver registers a panic notifier as well as
reboot and die notifiers. The callbacks registered are called in
atomic and very limited context - for instance, panic disables
preemption and local IRQs, also all secondary CPUs (not executing
the panic path) are shutdown.
With that said, taking a spinlock in this scenario is a dangerous
invitation for lockup scenarios. So, fix that by checking if the
spinlock is free to acquire in the panic notifier callback - if not,
bail-out and avoid a potential hang.
Fixes: 73b74620da05 ("driver: Google EFI SMI") Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ard Biesheuvel <ardb@kernel.org> Cc: David Gow <davidgow@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Julius Werner <jwerner@chromium.org> Cc: Petr Mladek <pmladek@suse.com> Reviewed-by: Evan Green <evgreen@chromium.org> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Link: https://lore.kernel.org/r/20220909200755.189679-1-gpiccoli@igalia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some initialization functions of this driver, memory is allocated with
'i' acting as an index variable and increasing from 0. The commit in
"Fixes" introduces some clean-up codes in case of allocation failure,
which free memory in reverse order with 'i' decreasing to 0. However,
there are some problems:
- The case i=0 is left out. Thus memory is leaked.
- In case memory allocation fails right from the start, the memory
freeing loops will start with i=-1 and invalid memory locations will
be accessed.
One of these loops has been fixed in commit 8a22f1effd08 ("staging:
vt6655: fix potential memory leak"). Fix the remaining erroneous loops.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_clk' from clk_prepare_enable() not released on lines:
58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_sleep_clk' from clk_prepare_enable() not released on
lines: 58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->phy_clk' from clk_prepare_enable() not released on lines:
58.
Fix this by calling proper clk_disable_unprepare calls.
Fixes: b63d59fddb73 ("phy: Group vendor specific phy drivers") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20220914051334.69282-1-dzm91@hust.edu.cn Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
lpuart_dma_shutdown tears down lpuart dma, but lpuart_flush_buffer can
still occur which in turn tries to access dma apis if lpuart_dma_tx_use
flag is true. At this point since dma is torn down, these dma apis can
abort. Set lpuart_dma_tx_use and the corresponding rx flag
lpuart_dma_rx_use to false in lpuart_dma_shutdown so that dmas are not
accessed after they are relinquished.
When opts->pnp_string is changed with configfs, new memory is allocated for
the string. It does not, however, update dev->pnp_string, even though the
memory is freed. When rquesting the string, the host then gets old or
corrupted data rather than the new string. The ieee 1284 id string should
be allowed to change while the device is connected.
The bug was introduced in commit 0d60940f97f0 ("usb: gadget: printer:
Remove pnp_string static buffer"), which changed opts->pnp_string from a
char[] to a char*.
This patch changes dev->pnp_string from a char* to a char** pointing to
opts->pnp_string.
commit 9f26c0af5a48 ("xhci: re-initialize the HC during resume if HCE was
set") introduced a new warning message when the host controller error
was set and re-initializing.
This is expected behavior on some designs which already set
`xhci->broken_suspend` so the new warning is alarming to some users.
Modify the code to only show the warning if this was a surprising behavior
to the XHCI driver.
When doing degrade/recover tests using the journal a kernel BUG
is hit at drivers/md/raid5.c:4381 in handle_parity_checks5():
BUG_ON(!test_bit(R5_UPTODATE, &dev->flags));
This was found to occur because handle_stripe_fill() was skipped
for stripes in the journal due to a condition in that function.
Thus blocks were not fetched and R5_UPTODATE was not set when
the code reached handle_parity_checks5().
To fix this, don't skip handle_stripe_fill() unless the stripe is
for read.
Fixes: c0ad6091bae6 ("md/r5cache: shift complex rmw from read path to write path") Link: https://lore.kernel.org/linux-raid/e05c4239-41a9-d2f7-3cfa-4aa9d2cea8c1@deltatee.com/ Suggested-by: Song Liu <song@kernel.org> Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The meson_nfc_ecc_correct() function accidentally does a right shift
instead of a left shift so it only works for BIT(0). Also use
BIT_ULL() because "correct_bitmap" is a u64 and we want to avoid
shift wrapping bugs.
Fixes: a8b6ef1f6111 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Liang Yang <liang.yang@amlogic.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/YuI2zF1hP65+LE7r@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.36 Word 78: Serial ATA features supported
states that:
If word 76 is not 0000h or FFFFh, word 78 reports the features supported
by the device. If this word is not supported, the word shall be cleared
to zero.
(This text also exists in really old ACS standards, e.g. ACS-3.)
The problem with ata_id_has_dipm() is that the while it performs a
check against 0 and 0xffff, it performs the check against
ATA_ID_FEATURE_SUPP (word 78), the same word where the feature bit
is stored.
Fix this by performing the check against ATA_ID_SATA_CAPABILITY
(word 76), like required by the spec. The feature bit check itself
is of course still performed against ATA_ID_FEATURE_SUPP (word 78).
Additionally, move the macro to the other ATA_ID_FEATURE_SUPP macros
(which already have this check), thus making it more likely that the
next ATA_ID_FEATURE_SUPP macro that is added will include this check.
Fixes: 43a086bfbe60 ("[libata] Link power management infrastructure") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.36 Word 78: Serial ATA features supported
states that:
If word 76 is not 0000h or FFFFh, word 78 reports the features supported
by the device. If this word is not supported, the word shall be cleared
to zero.
(This text also exists in really old ACS standards, e.g. ACS-3.)
Additionally, move the macro to the other ATA_ID_FEATURE_SUPP macros
(which already have this check), thus making it more likely that the
next ATA_ID_FEATURE_SUPP macro that is added will include this check.
Fixes: 05cb3aeddcf4 ("libata: Implement NCQ autosense") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ACS-5 section
7.13.6.36 Word 78: Serial ATA features supported
states that:
If word 76 is not 0000h or FFFFh, word 78 reports the features supported
by the device. If this word is not supported, the word shall be cleared
to zero.
(This text also exists in really old ACS standards, e.g. ACS-3.)
Additionally, move the macro to the other ATA_ID_FEATURE_SUPP macros
(which already have this check), thus making it more likely that the
next ATA_ID_FEATURE_SUPP macro that is added will include this check.
Fixes: 2eedf630a0e5 ("ahci: implement aggressive SATA device sleep support") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log