Explicit FPU selection has been introduced in commit 2db7f377222e
("[ARM] Enable VFP to be built when non-VFP capable CPUs are selected")
to make use of assembler mnemonics for VFP instructions.
However, clang currently does not support passing assembler flags
like this and errors out with:
clang-10: error: the clang compiler does not support '-Wa,-mfpu=softvfp+vfp'
Make use of the .fpu assembler directives to select the floating point
hardware selectively. Also use the new unified assembler language
mnemonics. This allows to build these procedures with Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/762 Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vladimir Oltean [Tue, 28 Jun 2022 17:20:16 +0000 (20:20 +0300)]
net: mscc: ocelot: allow unregistered IP multicast flooding
Flooding of unregistered IP multicast has been broken (both to other
switch ports and to the CPU) since the ocelot driver introduction, and
up until commit 966e57f8125e ("net: mscc: ocelot: fix broken IP
multicast flooding"), a bug fix for commit 966e93cb622d ("net: mscc:
ocelot: offload bridge port flags to device") from v5.12.
The driver used to set PGID_MCIPV4 and PGID_MCIPV6 to the empty port
mask (0), which made unregistered IPv4/IPv6 multicast go nowhere, and
without ever modifying that port mask at runtime.
The expectation is that such packets are treated as broadcast, and
flooded according to the forwarding domain (to the CPU if the port is
standalone, or to the CPU and other bridged ports, if under a bridge).
Since the aforementioned commit, the limitation has been lifted by
responding to SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS events emitted by the
bridge. As for host flooding, DSA synthesizes another call to
ocelot_port_bridge_flags() on the NPI port which ensures that the CPU
gets the unregistered multicast traffic it might need, for example for
smcroute to work between standalone ports.
But between v4.18 and v5.12, IP multicast flooding has remained unfixed.
Delete the inexplicable premature optimization of clearing PGID_MCIPV4
and PGID_MCIPV6 as part of the init sequence, and allow unregistered IP
multicast to be flooded freely according to the forwarding domain
established by PGID_SRC, by explicitly programming PGID_MCIPV4 and
PGID_MCIPV6 towards all physical ports plus the CPU port module.
Since commit d1bcae833b32f1 ("ELF: Don't generate unused section
symbols") [1], binutils (v2.36+) started dropping section symbols that
it thought were unused. This isn't an issue in general, but with
kexec_file.c, gcc is placing kexec_arch_apply_relocations[_add] into a
separate .text.unlikely section and the section symbol ".text.unlikely"
is being dropped. Due to this, recordmcount is unable to find a non-weak
symbol in .text.unlikely to generate a relocation record against.
Address this by dropping the weak attribute from these functions.
Instead, follow the existing pattern of having architectures #define the
name of the function they want to override in their headers.
drm_fb_helper_modinit has a lot of boilerplate for what is not very
simple functionality. Just open code it in the only caller using
IS_ENABLED and IS_MODULE, and skip the find_module check as a
request_module is harmless if the module is already loaded (and not
other caller has this find_module check either).
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jessica Yu <jeyu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call. Fortunately,
each platform already has a setup_arch function pointer, which means
it's easy to wire this up. This commit also removes some noisy log
messages that don't add much.
Fixes: b42ea56c3f66 ("powerpc/pseries: Implement arch_get_random_long() based on H_RANDOM") Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220611151015.548325-4-Jason@zx2c4.com Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 036ee7c01f74 ("kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This comment wasn't updated when we moved from read() to read_iter(), so
this patch makes the trivial fix.
Fixes: 46d5153b4686 ("random: convert to using fops->read_iter()") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 12a708dae0b5 ("module: Sort exported symbols"),
EXPORT_SYMBOL* is placed in the individual section ___ksymtab(_gpl)+<sym>
(3 leading underscores instead of 2).
Since then, modpost cannot detect the bad combination of EXPORT_SYMBOL
and __init/__exit.
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: f4dcee6d5110 ("ARM: Add platform support for LSI AXM55xx SoC") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220601090548.47616-1-linmq006@gmail.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
In brcmstb_init_sram, it pass dn to of_address_to_resource(),
of_address_to_resource() will call of_find_device_by_node() to take
reference, so we should release the reference returned by
of_find_matching_node().
Fixes: 275e9baf1087 ("soc: bcm: brcmstb: Add support for S2/S3/S5 suspend states (ARM)") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() checks null pointer.
Fixes: dfef50d24bce ("ARM: EXYNOS: Add support for mapping PMU base address via DT") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220523145513.12341-1-linmq006@gmail.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 09a5a01e2174 ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call.
Complicating things, however, is that POWER8 systems need some per-cpu
state and kmalloc, which isn't available at this stage. So we split
things up into an early phase and a later opportunistic phase. This
commit also removes some noisy log messages that don't add much.
Fixes: f017f5f493de ("powerpc: Implement arch_get_random_long/int() for powernv") Cc: stable@vger.kernel.org # v3.13+ Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Add of_node_put(), use pnv naming, minor change log editing] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220621140849.127227-1-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a special case to block_rtas_call() to allow the ibm,platform-dump RTAS
call through the RTAS filter if the buffer address is 0.
According to PAPR, ibm,platform-dump is called with a null buffer address
to notify the platform firmware that processing of a particular dump is
finished.
Without this, on a pseries machine with CONFIG_PPC_RTAS_FILTER enabled, an
application such as rtas_errd that is attempting to retrieve a dump will
encounter an error at the end of the retrieval process.
On execve[at], we are zero'ing out most of the thread register state
including gpr[0], which contains the syscall number. Due to this, we
fail to trigger the syscall exit tracepoint properly. Fix this by
retaining gpr[0] in the thread register state.
Fix a boot crash on a c8000 machine as reported by Dave. Basically it changes
patch_map() to return an alias mapping to the to-be-patched code in order to
prevent writing to write-protected memory.
In calibrate_ccount(), of_find_compatible_node() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Cc: stable@vger.kernel.org Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617124432.4049006-1-windhl@126.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In machine_setup(), of_find_compatible_node() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Cc: stable@vger.kernel.org Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617115323.4046905-1-windhl@126.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c3fdc9ebf074 ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models.
Some models like the Nuvision Solo 10 Draw tablet actually need the
old hardcoded 80ųA bias current for battery temperature monitoring
to work properly.
Add a quirk entry for the Nuvision Solo 10 Draw to the DMI quirk table
to restore setting the bias current to 80ųA on this model.
Ensure that the irq_work has completed before the trigger is freed.
==================================================================
BUG: KASAN: use-after-free in irq_work_run_list
Read of size 8 at addr 0000000064702248 by task python3/25
On fxls8471, after set the reset bit, the device will reset immediately,
will not give ACK. So ignore the return value of this reset operation,
let the following code logic to check whether the reset operation works.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Fixes: e0c1f7544323 ("iio: mma8452: Initialise before activating") Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/1655292718-14287-1-git-send-email-haibo.chen@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: 9610f70b81a2 ("iio: mxc4005: add data ready trigger for mxc4005") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-4-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: 524d1fd74343 ("iio: chemical: ccs811: Add support for data ready trigger") Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20220524181150.9240-5-ddrokosov@sberdevices.ru Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The complete() function may be called even though request is not
completed. In this case, it's necessary to check request status so
as not to set device address wrongly.
Fixes: 1c3890f3f0e7 ("usb: chipidea: udc: update gadget states according to ch9")
cc: <stable@vger.kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20220623030242.41796-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Events CPU_CYCLES and INSTRUCTIONS can be submitted with two different
perf_event attribute::type values:
- PERF_TYPE_HARDWARE: when invoked via perf tool predefined events name
cycles or cpu-cycles or instructions.
- pmu->type: when invoked via perf tool event name cpu_cf/CPU_CYLCES/ or
cpu_cf/INSTRUCTIONS/. This invocation also selects the PMU to which
the event belongs.
Handle both type of invocations identical for events CPU_CYLCES and
INSTRUCTIONS. They address the same hardware.
The result is different when event modifier exclude_kernel is also set.
Invocation with event modifier for user space event counting fails.
This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().
Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.
Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.
Fixes: 3a0a20296560 ("virtio_net: setup xdp_rxq_info") Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit ea8945e8f37a ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: ea8945e8f37a ("igb: Move DMA Coalescing init code to separate function.") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When enabling a type_in_mask irq, the type_buf contents must be
AND'd with the mask of the IRQ we're enabling to avoid enabling
other IRQs by accident, which can happen if several type_in_mask
irqs share a mask register.
Fixes: 9072dbe5f3e7 ("regmap: irq: handle HW using separate rising/falling edge interrupts") Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Link: https://lore.kernel.org/r/20220620200644.1961936-2-aidanmacdonald.0x0@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 6c429a84c56e ("ice: Implement handlers for ethtool PHY/link operations") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The recent patch to make afs_getattr consult the server didn't account
for the pseudo-inodes employed by the dynamic root-type afs superblock
not having a volume or a server to access, and thus an oops occurs if
such a directory is stat'd.
Fix this by checking to see if the vnode->volume pointer actually points
anywhere before following it in afs_getattr().
This can be tested by stat'ing a directory in /afs. It may be
sufficient just to do "ls /afs" and the oops looks something like:
commit ab4fd97bb851 ("[PATCH] mips: update IRQ handling for vr41xx") added
a function irq_dispatch, and it'll increase irq_err_count when the get_irq
callback returns a negative value, but increase irq_err_count in get_irq
was not removed.
And also, modpost complains once gpio-vr41xx drivers become modules.
ERROR: modpost: "irq_err_count" [drivers/gpio/gpio-vr41xx.ko] undefined!
So it would be a good idea to remove repetitive increase irq_err_count in
get_irq callback.
Fixes: cc5be02f60c6 ("MIPS: Update VR41xx GPIO driver to use gpiolib") Fixes: ab4fd97bb851 ("[PATCH] mips: update IRQ handling for vr41xx") Reported-by: k2ci <kernel-bot@kylinos.cn> Signed-off-by: huhai <huhai@kylinos.cn> Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
After setting the sock ktls, update ctx->sk_proto to sock->sk_prot by
tls_update(), so now ctx->sk_proto->close is tls_sk_proto_close(). When
close the sock, tls_sk_proto_close() is called for sock->sk_prot->close
is tls_sk_proto_close(). But ctx->sk_proto->close() will be executed later
in tls_sk_proto_close(). Thus tls_sk_proto_close() executed repeatedly
occurred. That will trigger the following bug.
=================================================================
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:tls_sk_proto_close+0xd8/0xaf0 net/tls/tls_main.c:306
Call Trace:
<TASK>
tls_sk_proto_close+0x356/0xaf0 net/tls/tls_main.c:329
inet_release+0x12e/0x280 net/ipv4/af_inet.c:428
__sock_release+0xcd/0x280 net/socket.c:650
sock_close+0x18/0x20 net/socket.c:1365
Updating a proto which is same with sock->sk_prot is incorrect. Add proto
and sock->sk_prot equality check at the head of tls_update() to fix it.
Fixes: 8e0fd2340797 ("bpf: sockmap/tls, close can race with map free") Reported-by: syzbot+29c3c12f3214b85ad081@syzkaller.appspotmail.com Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 0c5e1bb756ca ("erspan: auto detect truncated ipv6 packets.") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_graph_get_remote_node() returns remote device node pointer with
refcount incremented, we should use of_node_put() on it
when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 6bbe0e33a90b ("drm: convert drivers to use of_graph_get_remote_node") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/488473/ Link: https://lore.kernel.org/r/20220607110841.53889-1-linmq006@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
qopt.latency is __u32, psched_tdiff_t is signed long,
(psched_tdiff_t)(UINT_MAX) is negative for 32-bit platforms, so
qopt.latency is always UINT_MAX.
Fix it by using psched_time_t (u64) instead.
Note: confusingly, users have two ways to specify 'latency':
1. normally, via '__u32 latency' in struct tc_netem_qopt;
2. via the TCA_NETEM_LATENCY64 attribute, which is s64.
For the second case, theoretically 'latency' could be negative. This
patch ignores that corner case, since it is broken (i.e. assigning a
negative s64 to __u32) anyways, and should be handled separately.
The bonding ARP monitor fails to decrement send_peer_notif, the
number of peer notifications (gratuitous ARP or ND) to be sent. This
results in a continuous series of notifications.
Correct this by decrementing the counter for each notification.
Reported-by: Jonathan Toppins <jtoppins@redhat.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Fixes: ab0a4d932d7e ("bonding: Fix RTNL: assertion failed at net/core/rtnetlink.c for ab arp monitor") Link: https://lore.kernel.org/netdev/b2fd4147-8f50-bebd-963a-1a3e8d1d9715@redhat.com/ Tested-by: Jonathan Toppins <jtoppins@redhat.com> Reviewed-by: Jonathan Toppins <jtoppins@redhat.com> Link: https://lore.kernel.org/r/9400.1655407960@famine Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even when the eth port is resticted to work with speeds not higher than 1G,
and so the eth driver is requesting the phy (via phylink) to advertise up
to 1000BASET support, the aquantia phy device is still advertising for 2.5G
and 5G speeds.
Clear these advertising defaults when requested.
Cc: Ondrej Spacek <ondrej.spacek@nxp.com> Fixes: a9894f007b7e1 ("net: phy: aquantia: add support for auto-negotiation configuration") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220610084037.7625-1-claudiu.manoil@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A customer reported a request_socket leak in a Calico cloud environment. We
found that a BPF program was doing a socket lookup with takes a refcnt on
the socket and that it was finding the request_socket but returning the parent
LISTEN socket via sk_to_full_sk() without decrementing the child request socket
1st, resulting in request_sock slab object leak. This patch retains the
existing behaviour of returning full socks to the caller but it also decrements
the child request_socket if one is present before doing so to prevent the leak.
Thanks to Curtis Taylor for all the help in diagnosing and testing this. And
thanks to Antoine Tenart for the reproducer and patch input.
v2 of this patch contains, refactor as per Daniel Borkmann's suggestions to
validate RCU flags on the listen socket so that it balances with bpf_sk_release()
and update comments as per Martin KaFai Lau's suggestion. One small change to
Daniels suggestion, put "sk = sk2" under "if (sk2 != sk)" to avoid an extra
instruction.
Fixes: c0ef450c4e84 ("bpf: Check sk_fullsock() before returning from bpf_sk_lookup()") Fixes: aa1f46455534 ("bpf: add skc_lookup_tcp helper") Co-developed-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Curtis Taylor <cutaylor-pub@yahoo.com> Cc: Martin KaFai Lau <kafai@fb.com> Link: https://lore.kernel.org/bpf/56d6f898-bde0-bb25-3427-12a330b29fb8@iogearbox.net Link: https://lore.kernel.org/bpf/20220615011540.813025-1-jmaxwell37@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs
to write AT commands to this device node to query status, set APN,
set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the
data connection has been established, Linux host can access 5G data
network via this interface.
"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
random.c ratelimits how much it warns about uninitialized urandom reads
using __ratelimit(). When the RNG is finally initialized, it prints the
number of missed messages due to ratelimiting.
It has been this way since that functionality was introduced back in
2018. Recently, 13cd7980484c ("random: remove ratelimiting for in-kernel
unseeded randomness") put a bit more stress on the urandom ratelimiting,
which teased out a bug in the implementation.
Specifically, when under pressure, __ratelimit() will print its own
message and reset the count back to 0, making the final message at the
end less useful. Secondly, it does so as a pr_warn(), which apparently
is undesirable for people's CI.
Fortunately, __ratelimit() has the RATELIMIT_MSG_ON_RELEASE flag exactly
for this purpose, so we set the flag.
Fixes: a0596dd97db5 ("random: rate limit unseeded randomness warnings") Cc: stable@vger.kernel.org Reported-by: Jon Hunter <jonathanh@nvidia.com> Reported-by: Ron Economos <re@w6rz.net> Tested-by: Ron Economos <re@w6rz.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f569a3ade581 ("dm mirror log: round up region bitmap size to
BITS_PER_LONG") introduced a regression on 64-bit architectures in the
lvm testsuite tests: lvcreate-mirror, mirror-names and vgsplit-operation.
If the device is shrunk, we need to clear log bits beyond the end of the
device. The code clears bits up to a 32-bit boundary and then calculates
lc->sync_count by summing set bits up to a 64-bit boundary (the commit
changed that; previously, this boundary was 32-bit too). So, it was using
some non-zeroed bits in the calculation and this caused misbehavior.
Fix this regression by clearing bits up to BITS_PER_LONG boundary.
Fixes: f569a3ade581 ("dm mirror log: round up region bitmap size to BITS_PER_LONG") Cc: stable@vger.kernel.org Reported-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Archives the current era
2. Commits the metadata, as part of the RPC call for archiving the
current era
3. Stops the worker
Until the worker stops, it might write to the metadata again. Moreover,
these writes are not flushed to disk immediately, but are cached by the
dm-bufio client, which writes them back asynchronously.
As a result, the committed metadata of a suspended dm-era device might
not be consistent with the in-core metadata.
In some cases, this can result in the corruption of the on-disk
metadata. Suppose the following sequence of events:
1. Load a new table, e.g. a snapshot-origin table, to a device with a
dm-era table
2. Suspend the device
3. dm-era commits its metadata, but the worker does a few more metadata
writes until it stops, as part of digesting an archived writeset
4. These writes are cached by the dm-bufio client
5. Load the dm-era table to another device.
6. The new instance of the dm-era target loads the committed, on-disk
metadata, which don't include the extra writes done by the worker
after the metadata commit.
7. Resume the new device
8. The new dm-era target instance starts using the metadata
9. Resume the original device
10. The destructor of the old dm-era target instance is called and
destroys the dm-bufio client, which results in flushing the cached
writes to disk
11. These writes might overwrite the writes done by the new dm-era
instance, hence corrupting its metadata.
Fix this by committing the metadata after the worker stops running.
stop_worker uses flush_workqueue to flush the current work. However, the
work item may re-queue itself and flush_workqueue doesn't wait for
re-queued works to finish.
This could result in the worker changing the metadata after they have
been committed, or writing to the metadata concurrently with the commit
in the postsuspend thread.
Use drain_workqueue instead, which waits until the work and all
re-queued works finish.
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 607663bc3b1d ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: 16c1b23db3788 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.
As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.
This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.
The offending commit is partially reverted to restore the expected
behavior.
The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.
There is not have Headset Mic verb table in BIOS default.
So, it will have recording issue from headset MIC.
Add the verb table value without jack detect. It will turn on Headset Mic.
Currently the Conexant codec driver sets up the beep NID after calling
snd_hda_gen_parse_auto_config(). It turned out that this results in
the insufficient setup for the beep control, as the generic parser
handles the fake path in snd_hda_gen_parse_auto_config() only if the
beep_nid is set up beforehand.
For dealing with the beep widget properly, call cx_auto_parse_beep()
before snd_hda_gen_parse_auto_config() call.
Like the previous fix for Conexant codec, the beep_nid has to be set
up before calling snd_hda_gen_parse_auto_config(); otherwise it'd miss
the path setup.
Fix the call order for addressing the missing beep setup.
It used to be that mix_interrupt_randomness() would credit 1 bit each
time it ran, and so add_interrupt_randomness() would schedule mix() to
run every 64 interrupts, a fairly arbitrary number, but nonetheless
considered to be a decent enough conservative estimate.
Since 4f280103bfeb ("random: do not use input pool from hard IRQs"),
mix() is now able to credit multiple bits, depending on the number of
calls to add(). This was done for reasons separate from this commit, but
it has the nice side effect of enabling this patch to schedule mix()
less often.
Currently the rules are:
a) Credit 1 bit for every 64 calls to add().
b) Schedule mix() once a second that add() is called.
c) Schedule mix() once every 64 calls to add().
Rules (a) and (c) no longer need to be coupled. It's still important to
have _some_ value in (c), so that we don't "over-saturate" the fast
pool, but the once per second we get from rule (b) is a plenty enough
baseline. So, by increasing the 64 in rule (c) to something larger, we
avoid calling queue_work_on() as frequently during irq storms.
This commit changes that 64 in rule (c) to be 1024, which means we
schedule mix() 16 times less often. And it does *not* need to change the
64 in rule (a).
Fixes: b4d32c9bcc75 ("random: defer fast pool mixing to worker") Cc: stable@vger.kernel.org Cc: Dominik Brodowski <linux@dominikbrodowski.net> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for these ioctls:
* PIO_FONT, PIO_FONTX
* GIO_FONT, GIO_FONTX
* PIO_FONTRESET
As was demonstrated by commit 89f558ba837c (tty: make FONTX ioctl use
the tty pointer they were actually passed), these ioctls are not used
from userspace, as:
1) they used to be broken (set up font on current console, not the open
one) and racy (before the commit above)
2) KDFONTOP ioctl is used for years instead
Note that PIO_FONTRESET is defunct on most systems as VGA_CONSOLE is set
on them for ages. That turns on BROKEN_GRAPHICS_PROGRAMS which makes
PIO_FONTRESET just return an error.
We are removing KD_FONT_FLAG_OLD here as it was used only by these
removed ioctls. kd.h header exists both in kernel and uapi headers, so
we can remove the kernel one completely. Everyone includeing kd.h will
now automatically get the uapi one.
There are now unused definitions of the ioctl numbers and "struct
consolefontdesc" in kd.h, but as it is a uapi header, I am not touching
these.
Invalidating the buffer memory in arch_sync_dma_for_device() for
FROM_DEVICE transfers
When using the streaming DMA API to map a buffer prior to inbound
non-coherent DMA (i.e. DMA_FROM_DEVICE), we invalidate any dirty CPU
cachelines so that they will not be written back during the transfer and
corrupt the buffer contents written by the DMA. This, however, poses two
potential problems:
(1) If the DMA transfer does not write to every byte in the buffer,
then the unwritten bytes will contain stale data once the transfer
has completed.
(2) If the buffer has a virtual alias in userspace, then stale data
may be visible via this alias during the period between performing
the cache invalidation and the DMA writes landing in memory.
Address both of these issues by cleaning (aka writing-back) the dirty
lines in arch_sync_dma_for_device(DMA_FROM_DEVICE) instead of discarding
them using invalidation.
Cc: Ard Biesheuvel <ardb@kernel.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Russell King <linux@armlinux.org.uk> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220606152150.GA31568@willie-the-truck Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Link: https://lore.kernel.org/r/20220610151228.4562-2-will@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 57c2c1517858 ("tcp: change source port randomizarion at
connect() time"), the table_perturb[] array was introduced and an
index was taken from the port_offset via hash_32(). But it turns
out that hash_32() performs a multiplication while the input here
comes from the output of SipHash in secure_seq, that is well
distributed enough to avoid the need for yet another hash.
Suggested-by: Amit Klein <aksecurity@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moshe Kol, Amit Klein, and Yossi Gilad reported being able to accurately
identify a client by forcing it to emit only 40 times more connections
than there are entries in the table_perturb[] table. The previous two
improvements consisting in resalting the secret every 10s and adding
randomness to each port selection only slightly improved the situation,
and the current value of 2^8 was too small as it's not very difficult
to make a client emit 10k connections in less than 10 seconds.
Thus we're increasing the perturb table from 2^8 to 2^16 so that the
same precision now requires 2.6M connections, which is more difficult in
this time frame and harder to hide as a background activity. The impact
is that the table now uses 256 kB instead of 1 kB, which could mostly
affect devices making frequent outgoing connections. However such
components usually target a small set of destinations (load balancers,
database clients, perf assessment tools), and in practice only a few
entries will be visited, like before.
A live test at 1 million connections per second showed no performance
difference from the previous value.
Reported-by: Moshe Kol <moshe.kol@mail.huji.ac.il> Reported-by: Yossi Gilad <yossi.gilad@mail.huji.ac.il> Reported-by: Amit Klein <aksecurity@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We'll need to further increase the size of this table and it's likely
that at some point its size will not be suitable anymore for a static
table. Let's allocate it on boot from inet_hashinfo2_init(), which is
called from tcp_init().
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il> Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il> Cc: Amit Klein <aksecurity@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here we're randomly adding between 0 and 7 random increments to the
selected source port in order to add some noise in the source port
selection that will make the next port less predictable.
With the default port range of 32768-60999 this means a worst case
reuse scenario of 14116/8=1764 connections between two consecutive
uses of the same port, with an average of 14116/4.5=3137. This code
was stressed at more than 800000 connections per second to a fixed
target with all connections closed by the client using RSTs (worst
condition) and only 2 connections failed among 13 billion, despite
the hash being reseeded every 10 seconds, indicating a perfectly
safe situation.
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il> Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il> Cc: Amit Klein <aksecurity@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amit Klein suggests that we use different parts of port_offset for the
table's index and the port offset so that there is no direct relation
between them.
Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Moshe Kol <moshe.kol@mail.huji.ac.il> Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il> Cc: Amit Klein <aksecurity@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even when implementing RFC 6056 3.3.4 (Algorithm 4: Double-Hash
Port Selection Algorithm), a patient attacker could still be able
to collect enough state from an otherwise idle host.
Idea of this patch is to inject some noise, in the
cases __inet_hash_connect() found a candidate in the first
attempt.
This noise should not significantly reduce the collision
avoidance, and should be zero if connection table
is already well used.
Note that this is not implementing RFC 6056 3.3.5
because we think Algorithm 5 could hurt typical
workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Dworken <ddworken@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In systemd systems setting a fixed MAC address through
the "dev_addr" module argument fails systematically.
When checking the MAC address after the interface is created
it always has the same but different MAC address to the one
supplied as argument.
This is partially caused by systemd which by default will
set an internally generated permanent MAC address for interfaces
that are marked as having a randomly generated address.
Commit 38008d64ea50659b ("usb: gadget: u_ether: fix race in
setting MAC address in setup phase") didn't take into account
the fact that the interface must be marked as having a set
MAC address when it's set as module argument.
Fixed by marking the interface with NET_ADDR_SET when
the "dev_addr" module argument is supplied.
Fixes: 38008d64ea50659b ("usb: gadget: u_ether: fix race in setting MAC address in setup phase") Cc: stable@vger.kernel.org Signed-off-by: Marian Postevca <posteuca@mutex.one> Link: https://lore.kernel.org/r/20220603153459.32722-1-posteuca@mutex.one Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch to a keyed guest does not require a classic sske as the other
guest CPUs are not accessing the key before the switch is complete.
By using the NQ SSKE things are faster especially with multiple guests.
The existing __lshrti3 was really inefficient, and the other two helpers
are also needed to compile some modules.
Add the missing versions, and export all of the symbols like arm64
already does.
This code is based on the assembly generated by libgcc builds.
This fixes a build break triggered by ubsan:
riscv64-unknown-linux-gnu-ld: lib/ubsan.o: in function `.L2':
ubsan.c:(.text.unlikely+0x38): undefined reference to `__ashlti3'
riscv64-unknown-linux-gnu-ld: ubsan.c:(.text.unlikely+0x42): undefined reference to `__ashrti3'
Signed-off-by: Olof Johansson <olof@lixom.net>
[paul.walmsley@sifive.com: use SYM_FUNC_{START,END} instead of
ENTRY/ENDPROC; note libgcc origin] Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
riscv's <vdso/processor.h> uses barrier() so it should include
<asm/barrier.h>
Fixes this build error:
CC [M] drivers/net/ethernet/emulex/benet/be_main.o
In file included from ./include/vdso/processor.h:10,
from ./arch/riscv/include/asm/processor.h:11,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
./arch/riscv/include/asm/vdso/processor.h: In function 'cpu_relax':
./arch/riscv/include/asm/vdso/processor.h:14:2: error: implicit declaration of function 'barrier' [-Werror=implicit-function-declaration]
14 | barrier();
This happens with a total of 5 networking drivers -- they all use
<linux/prefetch.h>.
rv64 allmodconfig now builds cleanly after this patch.
Fixes fallout from: bf82e747dd2a ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Fixes: 64b54cd2683d ("riscv: use vDSO common flow to reduce the latency of the time-related functions") Reported-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Arvind Sankar <nivedita@alum.mit.edu> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
[sudip: change in old path] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 437a17c0a7a6 ("kprobes: Init kprobes in early_initcall") enabled
using kprobes from early_initcall. Unfortunately at this point the
hardware debug infrastructure is not operational. The OS lock may still
be locked, and the hardware watchpoints may have unknown values when
kprobe enables debug monitors to single-step instructions.
Rather than using hardware single-step, append a BRK instruction after
the instruction to be executed out-of-line.
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 2183b9186077 ("openvswitch: Make tunnel set action attach a metadata dst") Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html Reported-by: Stéphane Graber <stgraber@ubuntu.com> Signed-off-by: Ilya Maximets <i.maximets@ovn.org> Acked-by: Aaron Conole <aconole@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport for 5.4: Removed handling of OVS_ACTION_ATTR_DEC_TTL as it
doesn't exist in this version. BUILD_BUG_ON condition adjusted
accordingly.] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the first ct() action the packet headers are almost fully
re-written. The next ct() tries to re-use the existing nfct entry
and marks the packet as invalid, so it gets dropped later in the
pipeline.
Clearing the cached conntrack entry whenever packet tuple is changed
to avoid the issue.
The flow key should not be cleared though, because we should still
be able to match on the ct_state if the recirculation happens after
the tuple change but before the next ct() action.
in current Linux, MTU policing does not take into account that packets at
the TC ingress have the L2 header pulled. Thus, the same TC police action
(with the same value of tcfp_mtu) behaves differently for ingress/egress.
In addition, the full GSO size is compared to tcfp_mtu: as a consequence,
the policer drops GSO packets even when individual segments have the L2 +
L3 + L4 + payload length below the configured valued of tcfp_mtu.
Improve the accuracy of MTU policing as follows:
- account for mac_len for non-GSO packets at TC ingress.
- compare MTU threshold with the segmented size for GSO packets.
Also, add a kselftest that verifies the correct behavior.
Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[dcaratti: fix conflicts due to lack of the following commits:
- commit 56e588b63b77 ("net/sched: act_police: add support for
packet-per-second policing")
- commit 11915b314ef6 ("selftests: forwarding: Add tc-police tests")
- commit 9badfde1d429 ("selftests: forwarding: Add tc-police tests for
packets per second")] Link: https://lore.kernel.org/netdev/876d597a0ff55f6ba786f73c5a9fd9eb8d597a03.1644514748.git.dcaratti@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC 12 enhanced -Waddress when comparing array address to null [0],
which warns:
drivers/virtio/virtio_pci_common.c: In function ‘vp_del_vqs’:
drivers/virtio/virtio_pci_common.c:257:29: warning: the comparison will always evaluate as ‘true’ for the pointer operand in ‘vp_dev->msix_affinity_masks + (sizetype)((long unsigned int)i * 256)’ must not be NULL [-Waddress]
257 | if (vp_dev->msix_affinity_masks[i])
| ^~~~~~
In fact, the verification is comparing the result of a pointer
arithmetic, the address "msix_affinity_masks + i", which will always
evaluate to true.
Under the hood, free_cpumask_var() calls kfree(), which is safe to pass
NULL, not requiring non-null verification. So remove the verification
to make compiler happy (happy compiler, happy life).
The HP EliteBook 630 is using ALC236 codec which used 0x02 to control mute LED
and 0x01 to control micmute LED. Therefore, add a quirk to make it works.
The HP EliteBook 840 G8 Notebook PC is using ALC236 codec which is
using 0x02 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
We capture a NULL pointer issue when resizing a corrupt ext4 image which
is freshly clear resize_inode feature (not run e2fsck). It could be
simply reproduced by following steps. The problem is because of the
resize_inode feature was cleared, and it will convert the filesystem to
meta_bg mode in ext4_resize_fs(), but the es->s_reserved_gdt_blocks was
not reduced to zero, so could we mistakenly call reserve_backup_gdb()
and passing an uninitialized resize_inode to it when adding new group
descriptors.
mkfs.ext4 /dev/sda 3G
tune2fs -O ^resize_inode /dev/sda #forget to run requested e2fsck
mount /dev/sda /mnt
resize2fs /dev/sda 8G
The fix is simple, add a check in ext4_resize_begin() to make sure that
the es->s_reserved_gdt_blocks is zero when the resize_inode feature is
disabled.
Cc: stable@kernel.org Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220601092717.763694-1-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since dx_make_map() may return -EFSCORRUPTED now, so change "count" to
be a signed integer so we can correctly check for an error code returned
by dx_make_map().
we can easily reproduce this problem with the following commands:
`fallocate -l100M disk`
`mkfs.ext4 -b 1024 -g 256 disk`
`mount disk /mnt`
`fsstress -d /mnt -l 0 -n 1000 -p 1`
The size must be smaller than or equal to EXT4_BLOCKS_PER_GROUP.
Therefore, "start + size <= ac->ac_o_ex.fe_logical" may occur
when the size is truncated. So start should be the start position of
the group where ac_o_ex.fe_logical is located after alignment.
In addition, when the value of fe_logical or EXT4_BLOCKS_PER_GROUP
is very large, the value calculated by start_off is more accurate.
Cc: stable@kernel.org Fixes: 8d80954c43e8 ("ext4: trim allocation requests to group size") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com> Link: https://lore.kernel.org/r/20220528110017.354175-2-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in dm-log rounds up bitset_size to 32 bits. It then uses
find_next_zero_bit_le on the allocated region. find_next_zero_bit_le
accesses the bitmap using unsigned long pointers. So, on 64-bit
architectures, it may access 4 bytes beyond the allocated size.
Fix this bug by rounding up bitset_size to BITS_PER_LONG.
This bug was found by running the lvm2 testsuite with kasan.
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit b0d3cb1b30f4 ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
Fixes: a6848bdc470f ("USB: gadget driver for LPC32xx") Cc: stable <stable@kernel.org> Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220603140246.64529-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when platform_get_resource()
fails to prevent memory leak.
goto error2 label instead error1 to fix this.
Fixes: 1a68fdb1dd16 ("usb: dwc2: check return value after calling platform_get_resource()") Cc: stable <stable@kernel.org> Acked-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220530085413.44068-1-linmq006@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding support for Cinterion device MV31 with Qualcomm
new baseline. Use different PIDs to separate it from
previous base line products.
All interfaces settings keep same as previous.
The expression for setting the size of the allocated bulk TX buffer
(`devpriv->usb_tx_buf`) is calling `usb_endpoint_maxp(devpriv->ep_rx)`,
which is using the wrong endpoint (should be `devpriv->ep_tx`). Fix it.
Fixes: f6d15c807df6 ("comedi: vmk80xx: fix transfer-buffer overflow") Cc: Johan Hovold <johan@kernel.org> Cc: stable@vger.kernel.org # 4.9+ Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20220607171819.4121-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though the DW I2C controller reference clock source is requested by
the method devm_clk_get() with non-optional clock requirement the way the
clock handler is used afterwards has a pure optional clock semantic
(though in some circumstances we can get a warning about the clock missing
printed in the system console). There is no point in reimplementing that
functionality seeing the kernel clock framework already supports the
optional interface from scratch. Thus let's convert the platform driver to
using it.
Note by providing this commit we get to fix two problems. The first one
was introduced in commit dd31dff0282d ("i2c: designware: Add support for
an interface clock"). It causes not having the interface clock (pclk)
enabled/disabled in case if the reference clock isn't provided. The second
problem was first introduced in commit 74b8b8ef60dd ("i2c: designware: Do
not require clock when SSCN and FFCN are provided"). Since that
modification the deferred probe procedure has been unsupported in case if
the interface clock isn't ready.
Fixes: dd31dff0282d ("i2c: designware: Add support for an interface clock") Fixes: 74b8b8ef60dd ("i2c: designware: Do not require clock when SSCN and FFCN are provided") Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log