When the DP83867 PHY is strapped to enable Fast Link Drop (FLD) feature
STRAP_STS2.STRAP_ FLD (reg 0x006F bit 10), the Energy Lost Threshold for
FLD Energy Lost Mode FLD_THR_CFG.ENERGY_LOST_FLD_THR (reg 0x002e bits 2:0)
will be defaulted to 0x2. This may cause the phy link to be unstable. The
new DP83867 DM recommends to always restore ENERGY_LOST_FLD_THR to 0x1.
Hence, restore default value of FLD_THR_CFG.ENERGY_LOST_FLD_THR to 0x1 when
FLD is enabled by bootstrapping as recommended by DM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PACKET_RX_RING can cause multiple writers to access the same slot if a
fast writer wraps the ring while a slow writer is still copying. This
is particularly likely with few, large, slots (e.g., GSO packets).
Synchronize kernel thread ownership of rx ring slots with a bitmap.
Writers acquire a slot race-free by testing tp_status TP_STATUS_KERNEL
while holding the sk receive queue lock. They release this lock before
copying and set tp_status to TP_STATUS_USER to release to userspace
when done. During copying, another writer may take the lock, also see
TP_STATUS_KERNEL, and start writing to the same slot.
Introduce a new rx_owner_map bitmap with a bit per slot. To acquire a
slot, test and set with the lock held. To release race-free, update
tp_status and owner bit as a transaction, so take the lock again.
This is the one of a variety of discussed options (see Link below):
* instead of a shadow ring, embed the data in the slot itself, such as
in tp_padding. But any test for this field may match a value left by
userspace, causing deadlock.
* avoid the lock on release. This leaves a small race if releasing the
shadow slot before setting TP_STATUS_USER. The below reproducer showed
that this race is not academic. If releasing the slot after tp_status,
the race is more subtle. See the first link for details.
* add a new tp_status TP_KERNEL_OWNED to avoid the transactional store
of two fields. But, legacy applications may interpret all non-zero
tp_status as owned by the user. As libpcap does. So this is possible
only opt-in by newer processes. It can be added as an optional mode.
* embed the struct at the tail of pg_vec to avoid extra allocation.
The implementation proved no less complex than a separate field.
The additional locking cost on release adds contention, no different
than scaling on multicore or multiqueue h/w. In practice, below
reproducer nor small packet tcpdump showed a noticeable change in
perf report in cycles spent in spinlock. Where contention is
problematic, packet sockets support mitigation through PACKET_FANOUT.
And we can consider adding opt-in state TP_KERNEL_OWNED.
Easy to reproduce by running multiple netperf or similar TCP_STREAM
flows concurrently with `tcpdump -B 129 -n greater 60000`.
Based on an earlier patchset by Jon Rosen. See links below.
I believe this issue goes back to the introduction of tpacket_rcv,
which predates git history.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg237222.html Suggested-by: Jon Rosen <jrosen@cisco.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jon Rosen <jrosen@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 4b74fb0e3e05 ("net: mvneta: Associate RX queues with each CPU") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: 12a1c7661082 ("net: dsa: tag_8021q: Create helper function for removing VLAN header") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a number of network port link up/down changes, sometimes the switch
port gets stuck in a state where it thinks it is still transmitting packets
but the cpu port is not actually transmitting anymore. In this state you
will see a message on the console
"mtk_soc_eth 1e100000.ethernet eth0: transmit timed out" and the Tx counter
in ifconfig will be incrementing on virtual port, but not incrementing on
cpu port.
The issue is that MAC TX/RX status has no impact on the link status or
queue manager of the switch. So the queue manager just queues up packets
of a disabled port and sends out pause frames when the queue is full.
Change the LINK bit to reflect the link status.
Fixes: b2cac9613626 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Reported-by: Andrew Smith <andrew.smith@digi.com> Signed-off-by: René van Dorst <opensource@vdorst.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5a5197d64263 ("net: dsa: add Broadcom tag RX/TX handler") Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the software CBS does not consider the packet sending time
when depleting the credits. It caused the throughput to be
Idleslope[kbps] * (Port transmit rate[kbps] / |Sendslope[kbps]|) where
Idleslope * (Port transmit rate / (Idleslope + |Sendslope|)) = Idleslope
is expected. In order to fix the issue above, this patch takes the time
when the packet sending completes into account by moving the anchor time
variable "last" ahead to the send completion time upon transmission and
adding wait when the next dequeue request comes before the send
completion time of the previous packet.
changelog:
V2->V3:
- remove unnecessary whitespace cleanup
- add the checks if port_rate is 0 before division
V1->V2:
- combine variable "send_completed" into "last"
- add the comment for estimate of the packet sending
Fixes: 92c6bd6c8cc7 ("net/sched: Introduce Credit Based Shaper (CBS) qdisc") Signed-off-by: Zh-yuan Ye <ye.zh-yuan@socionext.com> Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bpfilter UMH code was recently changed to log its informative messages to
/dev/kmsg, however this interface doesn't support SEEK_CUR yet, used by
dprintf(). As result dprintf() returns -EINVAL and doesn't log anything.
However there already had some discussions about supporting SEEK_CUR into
/dev/kmsg interface in the past it wasn't concluded. Since the only user of
that from userspace perspective inside the kernel is the bpfilter UMH
(userspace) module it's better to correct it here instead waiting a conclusion
on the interface.
Fixes: f5bfcceb660a ("net: bpfilter: print umh messages to /dev/kmsg") Signed-off-by: Bruno Meneguele <bmeneg@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_for_each_entry_from_reverse() iterates backwards over the list from
the current position, but in the error path we should start from the
previous position.
Fix this by using list_for_each_entry_continue_reverse() instead.
This suppresses the following error from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//spectrum_mr.c:655:34-38: ERROR:
invalid reference to the index variable of the iterator on line 636
Fixes: f9fc91e83986 ("mlxsw: spectrum: Add the multicast routing offloading logic") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During initialization the driver issues a software reset command and
then waits for the system status to change back to "ready" state.
However, before issuing the reset command the driver does not check that
the system is actually in "ready" state. On Spectrum-{1,2} systems this
was always the case as the hardware initialization time is very short.
On Spectrum-3 systems this is no longer the case. This results in the
software reset command timing-out and the driver failing to load:
Fix this by waiting for the system to become ready both before issuing
the reset command and afterwards. In case of failure, print the last
system status to aid in debugging.
Fixes: f4e26af0882b ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot was able to trigger a KMSAN warning in macsec_handle_frame
by attaching to a phonet device.
Macvlan has a similar check in macvlan_port_create.
v1->v2
- fix commit message typo
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 11dba2eebaf4 ("net/ipv4: Plumb support for filtering route dumps") Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com Fixes: aefd34382d1c ("net/hsr: Use list_head (and rcu) instead of array for slave devices.") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: bd0ef9097b8b ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e330a37d0387 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit bd0ef9097b8b ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: e330a37d0387 ("cxgb4: request the TX CIDX updates to status page") Fixes: bd0ef9097b8b ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note that the EC GPE processing need not be synchronized in
acpi_s2idle_wake() after invoking acpi_ec_dispatch_gpe(), because
that function checks the GPE status and dispatches its handler if
need be and the SCI action handler is not going to run anyway at
that point.
Moreover, it is better to drain all of the pending ACPI events
before restoring the working-state configuration of GPEs in
acpi_s2idle_restore(), because those events are likely to be related
to system wakeup, in which case they will not be relevant going
forward.
Rework the code to take these observations into account.
Tested-by: Kenneth R. Crudup <kenny@panix.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has turned out that the sdhci-tegra controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Bitan Biswas <bbiswas@nvidia.com> Reported-by: Peter Geis <pgwipeout@gmail.com> Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It has turned out that the sdhci-omap controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Reported-by: Anders Roxell <anders.roxell@linaro.org> Reported-by: Faiz Abbas <faiz_abbas@ti.com> Cc: <stable@vger.kernel.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Tested-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific
to the card. Potentially the timeout may exceed the host->max_busy_timeout.
If that becomes the case, mmc_sleep() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
The busy timeout that is computed for each erase/trim/discard operation,
can become quite long and may thus exceed the host->max_busy_timeout. If
that becomes the case, mmc_do_erase() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-by: Faiz Abbas <faiz_abbas@ti.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com> Tested-by: Faiz Abbas <faiz_abbas@ti.com> Tested-By: Peter Geis <pgwipeout@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Newer GCC warns about possible truncations of two generated path names as
we're concatenating the configurable sysfs and debugfs path prefixes
with a filename and placing the results in buffers of the same size as
the maximum length of the prefixes.
Newer GCC warns about a possible truncation of a generated sysfs path
name as we're concatenating a directory path with a file name and
placing the result in a buffer that is half the size of the maximum
length of the directory path (which is user controlled).
loopback_test.c: In function 'open_poll_files':
loopback_test.c:651:31: warning: '%s' directive output may be truncated writing up to 511 bytes into a region of size 255 [-Wformat-truncation=]
651 | snprintf(buf, sizeof(buf), "%s%s", dev->sysfs_entry, "iteration_count");
| ^~
loopback_test.c:651:3: note: 'snprintf' output between 16 and 527 bytes into a destination of size 255
651 | snprintf(buf, sizeof(buf), "%s%s", dev->sysfs_entry, "iteration_count");
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this by making sure the buffer is large enough the concatenated
strings.
Fixes: 6b0658f68786 ("greybus: tools: Add tools directory to greybus repo and add loopback") Fixes: 9250c0ee2626 ("greybus: Loopback_test: use poll instead of inotify") Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200312110151.22028-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we send PDU data, we want to optimize the tcp stack
operation if we have more data to send. So when we set MSG_MORE
when:
- We have more fragments coming in the batch, or
- We have a more data to send in this PDU
- We don't have a data digest trailer
- We optimize with the SUCCESS flag and omit the NVMe completion
(used if sq_head pointer update is disabled)
This addresses a regression in QD=1 with SUCCESS flag optimization
as we unconditionally set MSG_MORE when we didn't actually have
more data to send.
Fixes: cb1eee469e8f ("nvmet-tcp: implement C2HData SUCCESS optimization") Reported-by: Mark Wunderlich <mark.wunderlich@intel.com> Tested-by: Mark Wunderlich <mark.wunderlich@intel.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a system configured to trigger a crash_kexec() reboot, when only one CPU
is online and another CPU panics while starting-up, crash_smp_send_stop()
will fail to send any STOP message to the other already online core,
resulting in fail to freeze and registers not properly saved.
Moreover even if the proper messages are sent (case CPUs > 2)
it will similarly fail to account for the booting CPU when executing
the final stop wait-loop, so potentially resulting in some CPU not
been waited for shutdown before rebooting.
A tangible effect of this behaviour can be observed when, after a panic
with kexec enabled and loaded, on the following reboot triggered by kexec,
the cpu that could not be successfully stopped fails to come back online:
Make crash_smp_send_stop() account also for the online status of the
calling CPU while evaluating how many CPUs are effectively online: this way
the right number of STOPs is sent and all other stopped-cores's registers
are properly saved.
On a system with only one CPU online, when another one CPU panics while
starting-up, smp_send_stop() will fail to send any STOP message to the
other already online core, resulting in a system still responsive and
alive at the end of the panic procedure.
Make smp_send_stop() account also for the online status of the calling CPU
while evaluating how many CPUs are effectively online: this way, the right
number of STOPs is sent, so enforcing a proper freeze of the system at the
end of panic even under the above conditions.
Fixes: 1bdb924f6cbf9 ("arm64: SMP support") Reported-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent futex inode life time fix changed the ordering of the futex key
union struct members, but forgot to adjust the hash function accordingly,
As a result the hashing omits the leading 64bit and even hashes beyond the
futex key causing a bad hash distribution which led to a ~100% performance
regression.
Hand in the futex key pointer instead of a random struct member and make
the size calculation based of the struct offset.
Fixes: fb796c0eb40b ("futex: Fix inode life-time issue") Reported-by: Rong Chen <rong.a.chen@intel.com> Decoded-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Rong Chen <rong.a.chen@intel.com> Link: https://lkml.kernel.org/r/87h7yy90ve.fsf@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Jann, ihold() does not in fact guarantee inode
persistence. And instead of making it so, replace the usage of inode
pointers with a per boot, machine wide, unique inode identifier.
This sequence number is global, but shared (file backed) futexes are
rare enough that this should not become a performance issue.
Commit 734fb682938b ("mm/vmalloc: Sync unmappings in
__purge_vmap_area_lazy()") introduced a call to vmalloc_sync_all() in
the vunmap() code-path. While this change was necessary to maintain
correctness on x86-32-pae kernels, it also adds additional cycles for
architectures that don't need it.
Specifically on x86-64 with CONFIG_VMAP_STACK=y some people reported
severe performance regressions in micro-benchmarks because it now also
calls the x86-64 implementation of vmalloc_sync_all() on vunmap(). But
the vmalloc_sync_all() implementation on x86-64 is only needed for newly
created mappings.
To avoid the unnecessary work on x86-64 and to gain the performance
back, split up vmalloc_sync_all() into two functions:
* vmalloc_sync_mappings(), and
* vmalloc_sync_unmappings()
Most call-sites to vmalloc_sync_all() only care about new mappings being
synchronized. The only exception is the new call-site added in the
above mentioned commit.
Shile Zhang directed us to a report of an 80% regression in reaim
throughput.
Fixes: 734fb682938b ("mm/vmalloc: Sync unmappings in __purge_vmap_area_lazy()") Reported-by: kernel test robot <oliver.sang@intel.com> Reported-by: Shile Zhang <shile.zhang@linux.alibaba.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Borislav Petkov <bp@suse.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [GHES] Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20191009124418.8286-1-joro@8bytes.org Link: https://lists.01.org/hyperkitty/list/lkp@lists.01.org/thread/4D3JPPHBNOSPFK2KEPC6KGKS6J25AIDB/ Link: http://lkml.kernel.org/r/20191113095530.228959-1-shile.zhang@linux.alibaba.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0effd3d7e792 ("mm, THP, swap: delay splitting THP after swapped
out") supported writing THP to a swap device but forgot to upgrade an
older commit 5c7e6e859422 ("page-flags: define behavior of FS/IO-related
flags on compound pages") which could trigger a crash during THP
swapping out with DEBUG_VM_PGFLAGS=y,
This only happens with a mmotm patch "mm/memcontrol.c: allocate
shrinker_map on appropriate NUMA node" [2] which effectively calls
kmalloc_node for each possible node. SLUB however only allocates
kmem_cache_node on online N_NORMAL_MEMORY nodes, and relies on
node_to_mem_node to return such valid node for other nodes since commit a989b95dc4b5 ("slub: fall back to node_to_mem_node() node if allocating
on memoryless node"). This is however not true in this configuration
where the _node_numa_mem_ array is not initialized for nodes 0 and 2-31,
thus it contains zeroes and get_partial() ends up accessing
non-allocated kmem_cache_node.
A related issue was reported by Bharata (originally by Ramachandran) [3]
where a similar PowerPC configuration, but with mainline kernel without
patch [2] ends up allocating large amounts of pages by kmalloc-1k
kmalloc-512. This seems to have the same underlying issue with
node_to_mem_node() not behaving as expected, and might probably also
lead to an infinite loop with CONFIG_SLUB_CPU_PARTIAL [4].
This patch should fix both issues by not relying on node_to_mem_node()
anymore and instead simply falling back to NUMA_NO_NODE, when
kmalloc_node(node) is attempted for a node that's not online, or has no
usable memory. The "usable memory" condition is also changed from
node_present_pages() to N_NORMAL_MEMORY node state, as that is exactly
the condition that SLUB uses to allocate kmem_cache_node structures.
The check in get_partial() is removed completely, as the checks in
___slab_alloc() are now sufficient to prevent get_partial() being
reached with an invalid node.
This is just a cleanup addition to Jann's fix to properly update the
transaction ID for the slub slowpath in commit 8bdac3893835 ("mm: slub:
add missing TID bump..").
The transaction ID is what protects us against any concurrent accesses,
but we should really also make sure to make the 'freelist' comparison
itself always use the same freelist value that we then used as the new
next free pointer.
Jann points out that if we do all of this carefully, we could skip the
transaction ID update for all the paths that only remove entries from
the lists, and only update the TID when adding entries (to avoid the ABA
issue with cmpxchg and list handling re-adding a previously seen value).
But this patch just does the "make sure to cmpxchg the same value we
used" rather than then try to be clever.
This fixes possible lost wakeup introduced by commit 39e1d7f1f5c9.
Originally modifications to ep->wq were serialized by ep->wq.lock, but
in commit 39e1d7f1f5c9 ("epoll: use rwlock in order to reduce
ep_poll_callback() contention") a new rw lock was introduced in order to
relax fd event path, i.e. callers of ep_poll_callback() function.
After the change ep_modify and ep_insert (both are called on epoll_ctl()
path) were switched to ep->lock, but ep_poll (epoll_wait) was using
ep->wq.lock on wqueue list modification.
The bug doesn't lead to any wqueue list corruptions, because wake up
path and list modifications were serialized by ep->wq.lock internally,
but actual waitqueue_active() check prior wake_up() call can be
reordered with modifications of ep ready list, thus wake up can be lost.
And yes, can be healed by explicit smp_mb():
list_add_tail(&epi->rdlink, &ep->rdllist);
smp_mb();
if (waitqueue_active(&ep->wq))
wake_up(&ep->wp);
But let's make it simple, thus current patch replaces ep->wq.lock with
the ep->lock for wqueue modifications, thus wake up path always observes
activeness of the wqueue correcty.
Fixes: 39e1d7f1f5c9 ("epoll: use rwlock in order to reduce ep_poll_callback() contention") Reported-by: Max Neunhoeffer <max@arangodb.com> Signed-off-by: Roman Penyaev <rpenyaev@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Max Neunhoeffer <max@arangodb.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Christopher Kohlhoff <chris.kohlhoff@clearpool.io> Cc: Davidlohr Bueso <dbueso@suse.de> Cc: Jason Baron <jbaron@akamai.com> Cc: Jes Sorensen <jes.sorensen@gmail.com> Cc: <stable@vger.kernel.org> [5.1+] Link: http://lkml.kernel.org/r/20200214170211.561524-1-rpenyaev@suse.de
References: https://bugzilla.kernel.org/show_bug.cgi?id=205933 Bisected-by: Max Neunhoeffer <max@arangodb.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann has brought up a very interesting point [1]. While shared pages
are excluded from MADV_PAGEOUT normally, CoW pages can be easily
reclaimed that way. This can lead to all sorts of hard to debug
problems. E.g. performance problems outlined by Daniel [2].
There are runtime environments where there is a substantial memory
shared among security domains via CoW memory and a easy to reclaim way
of that memory, which MADV_{COLD,PAGEOUT} offers, can lead to either
performance degradation in for the parent process which might be more
privileged or even open side channel attacks.
The feasibility of the latter is not really clear to me TBH but there is
no real reason for exposure at this stage. It seems there is no real
use case to depend on reclaiming CoW memory via madvise at this stage so
it is much easier to simply disallow it and this is what this patch
does. Put it simply MADV_{PAGEOUT,COLD} can operate only on the
exclusively owned memory which is a straightforward semantic.
In section_deactivate(), pfn_to_page() doesn't work any more after
ms->section_mem_map is resetting to NULL in SPARSEMEM|!VMEMMAP case. It
causes a hot remove failure:
Prior to this commit, we only directly check the affected cgroup's
memory.high against its usage. However, it's possible that we are being
reclaimed as a result of hitting an ancestor memory.high and should be
penalised based on that, instead.
This patch changes memory.high overage throttling to use the largest
overage in its ancestors when considering how many penalty jiffies to
charge. This makes sure that we penalise poorly behaving cgroups in the
same way regardless of at what level of the hierarchy memory.high was
breached.
Fixes: 4dee1f0f648c ("mm, memcg: throttle allocators when failing reclaim over memory.high") Reported-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Chris Down <chris@chrisdown.name> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> [5.4.x+] Link: http://lkml.kernel.org/r/8cd132f84bd7e16cdb8fde3378cdbf05ba00d387.1584036142.git.chris@chrisdown.name Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4dee1f0f648c had a bunch of fixups to use the right division
method. However, it seems that after all that it still wasn't right --
div_u64 takes a 32-bit divisor.
The headroom is still large (2^32 pages), so on mundane systems you
won't hit this, but this should definitely be fixed.
Fixes: 4dee1f0f648c ("mm, memcg: throttle allocators when failing reclaim over memory.high") Reported-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Chris Down <chris@chrisdown.name> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: <stable@vger.kernel.org> [5.4.x+] Link: http://lkml.kernel.org/r/80780887060514967d414b3cd91f9a316a16ab98.1584036142.git.chris@chrisdown.name Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An eventfd monitors multiple memory thresholds of the cgroup, closes them,
the kernel deletes all events related to this eventfd. Before all events
are deleted, another eventfd monitors the memory threshold of this cgroup,
leading to a crash:
We can reproduce this problem in the following ways:
1. We create a new cgroup subdirectory and a new eventfd, and then we
monitor multiple memory thresholds of the cgroup through this eventfd.
2. closing this eventfd, and __mem_cgroup_usage_unregister_event ()
will be called multiple times to delete all events related to this
eventfd.
The first time __mem_cgroup_usage_unregister_event() is called, the
kernel will clear all items related to this eventfd in thresholds->
primary.
Since there is currently only one eventfd, thresholds-> primary becomes
empty, so the kernel will set thresholds-> primary and hresholds-> spare
to NULL. If at this time, the user creates a new eventfd and monitor
the memory threshold of this cgroup, kernel will re-initialize
thresholds-> primary.
Then when __mem_cgroup_usage_unregister_event () is called for the
second time, because thresholds-> primary is not empty, the system will
access thresholds-> spare, but thresholds-> spare is NULL, which will
trigger a crash.
In general, the longer it takes to delete all events related to this
eventfd, the easier it is to trigger this problem.
The solution is to check whether the thresholds associated with the
eventfd has been cleared when deleting the event. If so, we do nothing.
[akpm@linux-foundation.org: fix comment, per Kirill] Fixes: 78d99f1a569c ("cgroups: make cftype.unregister_event() void-returning") Signed-off-by: Chunguang Xu <brookxu@tencent.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/077a6f67-aefa-4591-efec-f2f3af2b0b02@gmail.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The offset into the array was specified in bytes but should
be in terms of 32-bit words. Also prevent large reads that
would also cause a buffer overread.
v2: Read from correct offset from internal storage buffer.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a rename whiteout, if btrfs_whiteout_for_rename() returns an error
we can end up returning from btrfs_rename() with the log context object
still in the root's log context list - this happens if 'sync_log' was
set to true before we called btrfs_whiteout_for_rename() and it is
dangerous because we end up with a corrupt linked list (root->log_ctxs)
as the log context object was allocated on the stack.
After btrfs_rename() returns, any task that is running btrfs_sync_log()
concurrently can end up crashing because that linked list is traversed by
btrfs_sync_log() (through btrfs_remove_all_log_ctxs()). That results in
the same issue that commit 5d914bffbe94a ("Btrfs: fix log context list
corruption after rename exchange operation") fixed.
Fixes: e500480aaca6bd ("Btrfs: sync log after logging new name") CC: stable@vger.kernel.org # 4.19+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libtraceevent (used by perf and trace-cmd) failed to parse the
xhci_urb_dequeue trace event. This is because the user space trace
event format parsing is not a full C compiler. It can handle some basic
logic, but is not meant to be able to handle everything C can do.
In cases where a trace event field needs to be converted from a number
to a string, there's the __print_symbolic() macro that should be used:
See samples/trace_events/trace-events-sample.h
Some xhci trace events open coded the __print_symbolic() causing the
user spaces tools to fail to parse it. This has to be replaced with
__print_symbolic() instead.
The syscall number of compat_clock_getres was erroneously set to 247
(__NR_io_cancel!) instead of 264. This causes the vDSO fallback of
clock_getres() to land on the wrong syscall for compat tasks.
armv7a-hardfloat-linux-gnueabi-ld: drivers/rtc/rtc-max8907.o: in function `max8907_rtc_probe':
rtc-max8907.c:(.text+0x400): undefined reference to `regmap_irq_get_virq'
In order to preserve backwards compatability with kmod tools, we have to
move the namespace field in Module.symvers last, as the depmod -e -E
option looks at the first three fields in Module.symvers to check symbol
versions (and it's expected they stay in the original order of crc,
symbol, module).
In addition, update an ancient comment above read_dump() in modpost that
suggested that the export type field in Module.symvers was optional. I
suspect that there were historical reasons behind that comment that are
no longer accurate. We have been unconditionally printing the export
type since 2.6.18 (commit c7fdb7d23db), which is over a decade ago now.
Fix up read_dump() to treat each field as non-optional. I suspect the
original read_dump() code treated the export field as optional in order
to support pre <= 2.6.18 Module.symvers (which did not have the export
type field). Note that although symbol namespaces are optional, the
field will not be omitted from Module.symvers if a symbol does not have
a namespace. In this case, the field will simply be empty and the next
delimiter or end of line will follow.
Cc: stable@vger.kernel.org Fixes: daa3ffd7ea2b ("modpost: add support for symbol namespaces") Tested-by: Matthias Maennich <maennich@google.com> Reviewed-by: Matthias Maennich <maennich@google.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_char was erroneously given the address of the pointer to the text
instead of the address of the text, thus leading to random crashes when
the user requests speaking a word while the current position is on a space
character and say_word_ctl is not enabled.
A scripted conversion from userland POLL* to kernel EPOLL* constants
mistakingly replaced the poll flags in the loopback_test tool, which
therefore no longer builds.
Clang's -Wpointer-to-int-cast deviates from GCC in that it warns when
casting to enums. The kernel does this in certain places, such as device
tree matches to set the version of the device being used, which allows
the kernel to avoid using a gigantic union.
To avoid a ton of false positive warnings, disable this particular part
of the warning, which has been split off into a separate diagnostic so
that the entire warning does not need to be turned off for clang. It
will be visible under W=1 in case people want to go about fixing these
easily and enabling the warning treewide.
If we call fiemap on a truncated file with none blocks allocated,
it makes sense we get nothing from this call. No output means
no blocks have been counted, but the call succeeded. It's a valid
response.
SAMA5D2x doesn't drive CMD line if GPIO is used as CD line (at least
SAMA5D27 doesn't). Fix this by forcing card-detect in the module
if module-controlled CD is not used.
Fixed commit addresses the problem only for non-removable cards. This
amends it to also cover gpio-cd case.
Cc: stable@vger.kernel.org Fixes: 0add7fc3e39f ("mmc: sdhci-of-at91: force card detect value for non removable devices") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/8d10950d9940468577daef4772b82a071b204716.1584290561.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vishay has published a new version of "Designing the VCNL4200 Into an
Application" application note in October 2019. The new version specifies
that there is +-20% of part to part tolerance. Although the application
note is related to vcnl4200, according to support the vcnl4040's "ASIC
is quite similar to that one for the VCNL4200".
So update the sampling periods (and comment), including the correct
sampling period for proximity. Both sampling periods are lower. Users
relying on the blocking behaviour of reading will get proximity
measurements much earlier.
Fixes: 9d1e13b66bb8 ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor") Reviewed-by: Guido Günther <agx@sigxcpu.org> Tested-by: Guido Günther <agx@sigxcpu.org> Signed-off-by: Tomas Novotny <tomas@novotny.cz> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vishay has published a new version of "Designing the VCNL4200 Into an
Application" application note in October 2019. The new version specifies
that there is +-20% of part to part tolerance. This explains the drift
seen during experiments. The proximity pulse width is also changed from
32us to 30us. According to the support, the tolerance also applies to
ambient light.
So update the sampling periods. As the reading is blocking, current
users may notice slightly longer response time.
Fixes: 58c3da58aaf2 ("iio: vcnl4000: add support for VCNL4200") Reviewed-by: Guido Günther <agx@sigxcpu.org> Signed-off-by: Tomas Novotny <tomas@novotny.cz> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The differential channels require writing the channel offset register (COR).
Otherwise they do not work in differential mode.
The configuration of COR is missing in triggered mode.
Fixes: 78962b87efd5 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the error message:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
Suppress the trigger irq handler. Make the buffer transfers directly
in DMA callback, instead.
Push buffers without timestamps, as timestamps are not supported
in DFSDM driver.
Fixes: 849ae50fbc9a ("iio: adc: stm32-dfsdm: add support for buffer modes") Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment, reading from in_magn_*_raw in sysfs tends to return
large values around 65000, even though the output of ak8974 is actually
limited to ±32768. This happens because the value is never converted
to the signed 16-bit integer variant.
Add an explicit cast to s16 to fix this.
Fixes: 30d5f42a0c83 ("iio: magn: add a driver for AK8974") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Waleij <linus.walleij@linaro.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Master mode should be disabled when stopping. This mainly impacts
possible other use-case after timer has been stopped. Currently,
master mode remains set (from start routine).
Fixes: db7bb2f6a499 ("iio: stm32 trigger: Add support for TRGO2 triggers") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: d5abe9cec37c ("iio: accel: st_accel: Add support for the SMO8840 ACPI id") Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPS30 uses triggered buffer, but the dependency is not specified in the
Kconfig file. Fix this by selecting IIO_BUFFER and IIO_TRIGGERED_BUFFER
config symbols.
Cc: stable@vger.kernel.org Fixes: 21367e62fad9 ("iio: chemical: add support for Sensirion SPS30 sensor") Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b75bee18fdfd ("take compat TIOC[SG]SERIAL treatment into
tty_compat_ioctl()") changed the compat version of TIOCGSERIAL to start
checking for the presence of the ->set_serial function pointer rather
than ->get_serial. This appears to be a copy-and-paste error, since
->get_serial is the function pointer that is called as well as the
pointer that is checked by the non-compat version of TIOCGSERIAL.
Fix this by checking the correct function pointer.
Commit b75bee18fdfd ("take compat TIOC[SG]SERIAL treatment into
tty_compat_ioctl()") changed the compat version of TIOCGSERIAL to start
copying a whole 'serial_struct32' to userspace rather than individual
fields, but failed to initialize all padding and fields -- namely the
hole after the 'iomem_reg_shift' field, and the 'reserved' field.
Fix this by initializing the struct to zero.
[v2: use sizeof, and convert the adjacent line for consistency.]
The return value checks in snd_pcm_plug_alloc() are covered with
snd_BUG_ON() macro that may trigger a kernel WARNING depending on the
kconfig. But since the error condition can be triggered by a weird
user space parameter passed to OSS layer, we shouldn't give the kernel
stack trace just for that. As it's a normal error condition, let's
remove snd_BUG_ON() macro usage there.
Each OSS PCM plugins allocate its internal buffer per pre-calculation
of the max buffer size through the chain of plugins (calling
src_frames and dst_frames callbacks). This works for most plugins,
but the rate plugin might behave incorrectly. The calculation in the
rate plugin involves with the fractional position, i.e. it may vary
depending on the input position. Since the buffer size
pre-calculation is always done with the offset zero, it may return a
shorter size than it might be; this may result in the out-of-bound
access as spotted by fuzzer.
This patch addresses those possible buffer overflow accesses by simply
setting the upper limit per the given buffer size for each plugin
before src_frames() and after dst_frames() calls.
The virmidi driver handles sysex event exceptionally in a short-cut
snd_seq_dump_var_event() call, but this missed the reset of the
running status. As a result, it may lead to an incomplete command
right after the sysex when an event with the same running status was
queued.
Fix it by clearing the running status properly via alling
snd_midi_event_reset_decode() for that code path.
The MIDI input event parser of the LINE6 driver may enter into an
endless loop when the unexpected data sequence is given, as it tries
to continue the secondary bytes without termination. Also, when the
input data is too short, the parser returns a negative error, while
the caller doesn't handle it properly. This would lead to the
unexpected behavior as well.
This patch addresses those issues by checking the return value
correctly and handling the one-byte event in the parser properly.
By default, tty_port_init() initializes those parameters to a multiple
of HZ. For instance in line 69 of tty_port.c:
port->close_delay = (50 * HZ) / 100;
https://github.com/torvalds/linux/blob/master/drivers/tty/tty_port.c#L69
With e.g. CONFIG_HZ = 250 (as this is the case for Ubuntu 18.04
linux-image-4.15.0-37-generic), the default setting for close_delay is
thus 125.
When ioctl(fd, TIOCGSERIAL, &s) is executed, the setting returned in
user space is '12' (125/10). When ioctl(fd, TIOCSSERIAL, &s) is then
executed with the same setting '12', the value is interpreted as '120'
which is different from the current setting and a EPERM error may be
raised by set_serial_info() if !CAP_SYS_ADMIN.
https://github.com/torvalds/linux/blob/master/drivers/usb/class/cdc-acm.c#L919
close_delay and closing_wait are specified in hundredth of a second but stored
internally in jiffies. Use the jiffies_to_msecs() and msecs_to_jiffies()
functions to convert from each other.
Locking the connector in ucsi_register_displayport() to make
sure that nothing can access the displayport alternate mode
before the function has finished and the alternate mode is
actually ready.
If the registration of the DisplayPort was not successful,
or if the port does not support DisplayPort alt mode in the
first place, the function ucsi_displayport_remove_partner()
will fail with NULL pointer dereference when it attempts to
access the driver data.
Adding a check to the function to make sure there really is
driver data for the device before modifying it.
This controller timeouts during suspend (S3) with
[ 240.521724] xhci_hcd 0000:30:00.3: WARN: xHC save state timeout
[ 240.521729] xhci_hcd 0000:30:00.3: ERROR mismatched command completion event
thus preventing the system from entering S3.
Moreover it remains in an undefined state where some connected devices stop
working until a reboot.
Apply the XHCI_SUSPEND_DELAY quirk to make it suspend properly.
We have been receiving bug reports that ethernet connections over
RTL8153 based ethernet adapters stops working after a while with
errors like these showing up in dmesg when the ethernet stops working:
This has been reported on Dell WD15 docks, Belkin USB-C Express Dock 3.1
docks and with generic USB to ethernet dongles using the RTL8153
chipsets. Some users have tried adding usbcore.quirks=0bda:8153:k to
the kernel commandline and all users who have tried this report that
this fixes this.
Also note that we already have an existing NO_LPM quirk for the RTL8153
used in the Microsoft Surface Dock (where it uses a different usb-id).
This commit adds a NO_LPM quirk for the generic Realtek RTL8153
0bda:8153 usb-id, fixing the Tx timeout errors on these devices.
This reverts commit 38d05c41836d ("drm/fbdev: Fallback to non tiled mode
if all tiles not present"). The commit causes flip done timeouts in CI.
Below are the sample errors thrown in logs:
[IGT] core_getversion: executing
[IGT] core_getversion: exiting, ret=0
Setting dangerous option reset - tainting kernel
drm:drm_atomic_helper_wait_for_dependencies] ERROR [CRTC:152:pipe B] flip_done timed out
drm:drm_atomic_helper_wait_for_dependencies] ERROR [CONNECTOR:299:DP-2] flip_done timed out
drm:drm_atomic_helper_wait_for_dependencies] ERROR [PLANE:92:plane 1B] flip_done timed out
[drm:drm_atomic_helper_wait_for_flip_done] ERROR [CRTC:152:pipe B] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] ERROR [CRTC:152:pipe B] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] ERROR [CONNECTOR:299:DP-2] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] ERROR [PLANE:92:plane 1B] flip_done timed out
[drm:drm_atomic_helper_wait_for_flip_done] ERROR [CRTC:152:pipe B] flip_done timed out
Console: switching to colour frame buffer device 480x135
[drm:drm_atomic_helper_wait_for_dependencies] ERROR [CRTC:152:pipe B] flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] ERROR [CONNECTOR:299:DP-2] flip_done timed out
Reverting the change for now to unblock CI execution.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Signed-off-by: Uma Shankar <uma.shankar@intel.com> Fixes: 38d05c41836d ("drm/fbdev: Fallback to non tiled mode if all tiles not present") Closes: https://gitlab.freedesktop.org/drm/intel/issues/6 Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191123091840.32382-1-uma.shankar@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Binderfs binder-control devices are cleaned up via binderfs_evict_inode
too() which will use refcount_dec_and_test(). However, we missed to set
the refcount for binderfs binder-control devices and so we underflowed
when the binderfs instance got unmounted. Pretty obvious oversight and
should have been part of the more general UAF fix. The good news is that
having test cases (suprisingly) helps.
Technically, we could detect that we're about to cleanup the
binder-control dentry in binderfs_evict_inode() and then simply clean it
up. But that makes the assumption that the binder driver itself will
never make use of a binderfs binder-control device after the binderfs
instance it belongs to has been unmounted and the superblock for it been
destroyed. While it is unlikely to ever come to this let's be on the
safe side. Performance-wise this also really doesn't matter since the
binder-control device is only every really when creating the binderfs
filesystem or creating additional binder devices. Both operations are
pretty rare.
The bfq_find_set_group() function takes as input a blkcg (which represents
a cgroup) and retrieves the corresponding bfq_group, then it updates the
bfq internal group hierarchy (see comments inside the function for why
this is needed) and finally it returns the bfq_group.
In the hierarchy update cycle, the pointer holding the correct bfq_group
that has to be returned is mistakenly used to traverse the hierarchy
bottom to top, meaning that in each iteration it gets overwritten with the
parent of the current group. Since the update cycle stops at root's
children (depth = 2), the overwrite becomes a problem only if the blkcg
describes a cgroup at a hierarchy level deeper than that (depth > 2). In
this case the root's child that happens to be also an ancestor of the
correct bfq_group is returned. The main consequence is that processes
contained in a cgroup at depth greater than 2 are wrongly placed in the
group described above by BFQ.
This commits fixes this problem by using a different bfq_group pointer in
the update cycle in order to avoid the overwrite of the variable holding
the original group reference.
Reported-by: Kwon Je Oh <kwonje.oh2@gmail.com> Signed-off-by: Carlo Nonato <carlo.nonato95@gmail.com> Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Below is sample callstack when the issue is reproduced on purpose by
reordering the updates of req->body and req->state and adding delay in
code between updates of req->state and req->body.
The virt_rmb() is added in the 'true' path of test_reply(). The "while"
is changed to "do while" so that test_reply() is used as a read memory
barrier.
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[How]
when we disable MST we should clear the cur link settings (lane_count=0 is
good enough). This will cause us to not reallocate payloads earlier than
expected and not throw the warning
The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: Yintian Tao <yttao@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Monk Liu <Monk.Liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When looking for the memblock where the kernel lives, we should check
that the memory range associated to the memblock entirely comprises the
kernel image and not only intersects with it.
projects / kernel.git / log