When support for the level triggered interrupt controller flavor was
added with cfd3f67275bd, we forgot to update the flags to be set to
contain IRQ_LEVEL. While the flow handler is correct, the output from
/proc/interrupts does not show such interrupts as being level triggered
when they are, correct that.
Fixes: cfd3f67275bd ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the supply for cf->data[3] (bit stream position of CAN error), in
case of a bus- or protocol-error, outside of the "switch (ecc &
SJA1000_ECC_MASK){}"-statement, because this bit stream position is
independent of the error type.
Fixes: 37ca9589408a ("can: Add driver for esd CAN-USB/2 device") Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu> Link: https://lore.kernel.org/all/20230216190450.3901254-2-frank.jungclaus@esd.eu Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit e309de7fca09 ("driver core: Add __alloc_size hint to devm
allocators") exposes a panic "BRK handler: Fatal exception" on the
hi3660_thermal_probe funciton.
This is because the function allocates memory for only one
sensors array entry, but tries to fill up a second one.
The value of last_rate in ieee80211_sta_rx_stats is degraded from u32 to
u16 after being assigned to rate variable, which causes information loss
in STA_STATS_FIELD_TYPE and later bitfields.
In crypto4xx_cipher_done, we should be unmapping the dst page, not
mapping it.
This was flagged by a sparse warning about the unused addr variable.
While we're at it, also fix a sparse warning regarding the unused
ctx variable in crypto4xx_ahash_done (by actually using it).
Fixes: d21d400275f4 ("crypto: amcc - Add crypt4xx driver") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
There's no reason for the tasklet callback to set an argument since it
always uses a global. Instead, use the global directly, in preparation
for converting the tasklet subsystem to modern callback conventions.
Similarly to commit b50c91ad9a09 ("ARM: 8938/1: kernel: initialize
broadcast hrtimer based clock event device"), RISC-V needs to initiate
hrtimer based broadcast clock event device before C3STOP can be used.
Otherwise, the introduction of C3STOP for the RISC-V arch timer in
commit 7e2e6d223646 ("clocksource/drivers/riscv: Events are stopped
during CPU suspend") leaves us without any broadcast timer registered.
This prevents the kernel from entering oneshot mode, which breaks timer
behaviour, for example clock_nanosleep().
A test app that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250
& C3STOP enabled, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/ Fixes: 7e2e6d223646 ("clocksource/drivers/riscv: Events are stopped during CPU suspend") Suggested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Anup Patel <apatel@ventanamicro.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Link: https://lore.kernel.org/r/20230103141102.772228-2-apatel@ventanamicro.com Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_PROC_FS is not set, there is a build error for an unused
function. Make PROC_HARDWARE depend on PROC_FS to prevent this error.
In file included from ../arch/m68k/kernel/setup.c:3:
../arch/m68k/kernel/setup_mm.c:477:12: error: 'hardware_proc_show' defined but not used [-Werror=unused-function]
477 | static int hardware_proc_show(struct seq_file *m, void *v)
| ^~~~~~~~~~~~~~~~~~
Use the akcipher_request_complete helper instead of calling the
completion function directly. In fact the previous code was buggy
in that EINPROGRESS was never passed back to the original caller.
rds_rm_zerocopy_callback() uses list_add_tail() with swapped
arguments. This links the list head with the new entry, losing
the references to the remaining part of the list.
Fixes: 6a9be51d976d ("rds: use list structure to track information for zerocopy completion notification") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code assumes that everything that comes after nlmsgerr are nlattrs.
When calculating their size, it does not account for the initial
nlmsghdr. This may lead to accessing uninitialized memory.
This fixes all instances of which requires to allocate a buffer calling
alloc_skb which may release the chan lock and reacquire later which
makes it possible that the chan is disconnected in the meantime.
Fixes: b423603811b8 ("Bluetooth: Lock the L2CAP channel when sending") Reported-by: Alexander Coffin <alex.coffin@matician.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 846632d286c9 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tap_open() passes a `struct socket` embedded in a `struct
tap_queue` allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
On default configuration, the type confused field overlaps with
padding bytes between `int vnet_hdr_sz` and `struct tap_dev __rcu
*tap` in `struct tap_queue`, which makes the uid of all tap sockets 0,
i.e., the root one.
Fix the assignment by using sock_init_data_uid().
Fixes: d999f2405cd7 ("net: core: Add a UID field to struct sock.") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tun_chr_open() passes a `struct socket` embedded in a `struct
tun_file` allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
On default configuration, the type confused field overlaps with the
high 4 bytes of `struct tun_struct __rcu *tun` of `struct tun_file`,
NULL at the time of call, which makes the uid of all tun sockets 0,
i.e., the root one.
Fix the assignment by using sock_init_data_uid().
Fixes: d999f2405cd7 ("net: core: Add a UID field to struct sock.") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add sock_init_data_uid() to explicitly initialize the socket uid.
To initialise the socket uid, sock_init_data() assumes a the struct
socket* sock is always embedded in a struct socket_alloc, used to
access the corresponding inode uid. This may not be true.
Examples are sockets created in tun_chr_open() and tap_open().
Fixes: d999f2405cd7 ("net: core: Add a UID field to struct sock.") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 8d7e9a84e516 ("irqchip/ti-sci-intr: Add support for Interrupt Router driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102085611.3955984-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b39f5e95dfd5 ("irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102084208.3951758-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 7838f6b56af0 ("irqchip: Add the Alpine MSIX interrupt controller") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102082811.3947760-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the error path after calling dev_set_name(), the device
name is leaked. To fix this, calling dev_set_name() before
device_register(), and call put_device() if it returns error.
All the resources is released in powercap_release(), so it
can return from powercap_register_zone() directly.
Fixes: 296219659557 ("PowerCap: Add class driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As it is seqiv only handles the special return value of EINPROGERSS,
which means that in all other cases it will free data related to the
request.
However, as the caller of seqiv may specify MAY_BACKLOG, we also need
to expect EBUSY and treat it in the same way. Otherwise backlogged
requests will trigger a use-after-free.
Fixes: 8c02688b2651 ("[CRYPTO] seqiv: Add Sequence Number IV Generator") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
As it is essiv only handles the special return value of EINPROGERSS,
which means that in all other cases it will free data related to the
request.
However, as the caller of essiv may specify MAY_BACKLOG, we also need
to expect EBUSY and treat it in the same way. Otherwise backlogged
requests will trigger a use-after-free.
The /dma/dma0chan0 sysfs file is not removed since dma_chan object
has been released in ccp_dma_release() before releasing dma device.
A correct procedure would be: release dma channels first => unregister
dma device => release ccp dma object.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216888 Fixes: b48930106716 ("crypto: ccp - Release dma channels before dmaengine unrgister") Tested-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: Koba Ko <koba.ko@canonical.com> Reviewed-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When encountering a string bigger than the destination buffer (32 bytes),
the string is not properly NUL-terminated, causing buffer overreads later.
This for example happens on the Inspiron 3505, where the battery
model name is larger than 32 bytes, which leads to sysfs showing
the model name together with the serial number string (which is
NUL-terminated and thus prevents worse).
Fix this by using strscpy() which ensures that the result is
always NUL-terminated.
Fixes: 60b9578c2c8b ("ACPI: Battery: Allow extract string from integer") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a stack-out-of-bounds write that occurs in a WMI response callback
function that is called after a timeout occurs in ath9k_wmi_cmd().
The callback writes to wmi->cmd_rsp_buf, a stack-allocated buffer that
could no longer be valid when a timeout occurs. Set wmi->last_seq_id to
0 when a timeout occurred.
Fixes: ee12d32d37b7 ("ath9k_htc: Support for AR9271 chipset.") Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230104124130.10996-1-linuxlovemin@yonsei.ac.kr Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller detected a memory leak of skbs in ath9k_hif_usb_rx_stream().
While processing skbs in ath9k_hif_usb_rx_stream(), the already allocated
skbs in skb_pool are not freed if ath9k_hif_usb_rx_stream() fails. If we
have an incorrect pkt_len or pkt_tag, the input skb is considered invalid
and dropped. All the associated packets already in skb_pool should be
dropped and freed. Added a comment describing this issue.
The patch also makes remain_skb NULL after being processed so that it
cannot be referenced after potential free. The initialization of hif_dev
fields which are associated with remain_skb (rx_remain_len,
rx_transfer_len and rx_pad_len) is moved after a new remain_skb is
allocated.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
I've changed *STAT_* macros a bit in previous patch and I seems like
they become really unreadable. Align these macros definitions to make
code cleaner and fix folllowing checkpatch warning
ERROR: Macros with complex values should be enclosed in parentheses
Also, statistics macros now accept an hif_dev as argument, since
macros that depend on having a local variable with a magic name
don't abide by the coding style.
No functional change
Suggested-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/ebb2306d06a496cd1b032155ae52fdc5fa8cc2c5.1655145743.git.paskripkin@gmail.com
Stable-dep-of: 0af54343a762 ("wifi: ath9k: hif_usb: clean up skbs if ath9k_hif_usb_rx_stream() fails") Signed-off-by: Sasha Levin <sashal@kernel.org>
It is stated that ath9k_htc_rx_msg() either frees the provided skb or
passes its management to another callback function. However, the skb is
not freed in case there is no another callback function, and Syzkaller was
able to cause a memory leak. Also minor comment fix.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: ee12d32d37b7 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+e008dccab31bd3647609@syzkaller.appspotmail.com Reported-by: syzbot+6692c72009680f7c4eb2@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230104123546.51427-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
There is currently no return check for writing an authentication
type (HERMES_AUTH_SHARED_KEY or HERMES_AUTH_OPEN). It looks like
it was accidentally skipped.
This patch adds a return check similar to the other checks in
__orinoco_hw_setup_enc() for hermes_write_wordrec().
Previously acpi_ns_simple_repair() would crash if expected_btypes
contained any combination of ACPI_RTYPE_NONE with a different type,
e.g | ACPI_RTYPE_INTEGER because of slightly incorrect logic in the
!return_object branch, which wouldn't return AE_AML_NO_RETURN_VALUE
for such cases.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Link: https://github.com/acpica/acpica/pull/811 Fixes: aa966edd09fd ("ACPICA: Restore code that repairs NULL package elements in return values.") Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The helper mpi_read_raw_from_sgl sets the number of entries in
the SG list according to nbytes. However, if the last entry
in the SG list contains more data than nbytes, then it may overrun
the buffer because it only allocates enough memory for nbytes.
Fixes: ebd84f3efad6 ("lib/mpi: Add mpi sgl helpers") Reported-by: Roberto Sassu <roberto.sassu@huaweicloud.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The type of member ->irqs_sum is unsigned long, but kstat_cpu_irqs_sum()
returns int, which can result in truncation. Therefore, change the
kstat_cpu_irqs_sum() function's return value to unsigned long to avoid
truncation.
Fixes: 27a91eec7510 ("/proc/stat: scalability of irq num per cpu") Reported-by: Elliott, Robert (Servers) <elliott@hpe.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Cc: Tejun Heo <tj@kernel.org> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Josh Don <joshdon@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Microsoft introduced support in Windows XP for blocking port I/O
to various regions. For Windows compatibility ACPICA has adopted
the same protections and will disallow writes to those
(presumably) the same regions.
On some systems the AML included with the firmware will issue 4 byte
long writes to 0x80. These writes aren't making it over because of this
blockage. The first 4 byte write attempt is rejected, and then
subsequently 1 byte at a time each offset is tried. The first at 0x80
works, but then the next 3 bytes are rejected.
This manifests in bizarre failures for devices that expected the AML to
write all 4 bytes. Trying the same AML on Windows 10 or 11 doesn't hit
this failure and all 4 bytes are written.
Either some of these regions were wrong or some point after Windows XP
some of these regions blocks have been lifted.
In the last 15 years there doesn't seem to be any reports popping up of
this error in the Windows event viewer anymore. There is no documentation
at Microsoft's developer site indicating that Windows ACPI interpreter
blocks these regions. Between the lack of documentation and the fact that
the writes actually do work in Windows 10 and 11, it's quite likely
Windows doesn't actually enforce this anymore.
So to help the issue, only enforce Windows XP specific entries if the
latest _OSI supported is Windows XP. Continue to enforce the
ALWAYS_ILLEGAL entries.
Link: https://github.com/acpica/acpica/pull/817 Fixes: 5d79d694ba97 ("ACPICA: New: I/O port protection") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The key can be unaligned, so use the unaligned memory access helpers.
Fixes: b950149ee573 ("crypto: ghash-clmulni-intel - use C implementation for setkey()") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: 30f484d59ae7 ("libertas: Add spinlock to avoid race condition") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221207150008.111743-5-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: 8b0d880982c1 ("libertas: disable functionality when interface is down") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221207150008.111743-4-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: 6e049bb16cd0 ("libertas: use irqsave() in USB's complete callback") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221207150008.111743-3-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: 464eba015cc6 ("libertas_tf: use irqsave() in USB's complete callback") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221207150008.111743-2-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
After the DMA buffer is mapped to a physical address, address is stored
in pktids in brcmf_msgbuf_alloc_pktid(). Then, pktids is parsed in
brcmf_msgbuf_get_pktid()/brcmf_msgbuf_release_array() to obtain physaddr
and later unmap the DMA buffer. But when count is always equal to
pktids->array_size, physaddr isn't stored in pktids and the DMA buffer
will not be unmapped anyway.
Fixes: 1c189dc8aa72 ("brcmfmac: Adding msgbuf protocol.") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221207013114.1748936-1-shaozhengchao@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The brcmf_netdev_start_xmit() returns NETDEV_TX_OK without freeing skb
in case of pskb_expand_head() fails, add dev_kfree_skb() to fix it.
Compile tested only.
Fixes: 0e18af710058 ("brcmfmac: rework headroom check in .start_xmit()") Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/1668684782-47422-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type defining 'NETDEV_TX_OK' but this
driver returns '0' instead of 'NETDEV_TX_OK'.
Fix this by returning 'NETDEV_TX_OK' instead of '0'.
In the error path of ipw_wdev_init(), exception value is returned, and
the memory applied for in the function is not released. Also the memory
is not released in ipw_pci_probe(). As a result, memory leakage occurs.
So memory release needs to be added to the error path of ipw_wdev_init().
Fixes: 01c47cc68662 ("libipw: initiate cfg80211 API conversion (v2)") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221209012422.182669-1-shaozhengchao@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called to free and drop the SKB when
it's reset, so replace it with dev_kfree_skb_irq(). Compile tested
only.
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'ipw2100_msg_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_msg_allocate
Moreover, 'ipw2100_msg_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'status_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> status_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'bd_queue_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_rx_allocate
--> bd_queue_allocate
Moreover, 'ipw2100_rx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw2100_tx_allocate()' (ipw2100.c),
GFP_KERNEL can be used because it is called from the probe function.
The call chain is:
ipw2100_pci_init_one (the probe function)
--> ipw2100_queues_allocate
--> ipw2100_tx_allocate
Moreover, 'ipw2100_tx_allocate()' already uses GFP_KERNEL for some other
memory allocations.
When memory is allocated in 'ipw_queue_tx_init()' (ipw2200.c),
GFP_KERNEL can be used because it is called from a call chain that already
uses GFP_KERNEL and no spin_lock is taken in the between.
The call chain is:
ipw_up
--> ipw_load
--> ipw_queue_reset
--> ipw_queue_tx_init
'ipw_up()' already uses GFP_KERNEL for some other memory allocations.
There is a global-out-of-bounds reported by KASAN:
BUG: KASAN: global-out-of-bounds in
_rtl8812ae_eq_n_byte.part.0+0x3d/0x84 [rtl8821ae]
Read of size 1 at addr ffffffffa0773c43 by task NetworkManager/411
CPU: 6 PID: 411 Comm: NetworkManager Tainted: G D
6.1.0-rc8+ #144 e15588508517267d37
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009),
Call Trace:
<TASK>
...
kasan_report+0xbb/0x1c0
_rtl8812ae_eq_n_byte.part.0+0x3d/0x84 [rtl8821ae]
rtl8821ae_phy_bb_config.cold+0x346/0x641 [rtl8821ae]
rtl8821ae_hw_init+0x1f5e/0x79b0 [rtl8821ae]
...
</TASK>
The root cause of the problem is that the comparison order of
"prate_section" in _rtl8812ae_phy_set_txpower_limit() is wrong. The
_rtl8812ae_eq_n_byte() is used to compare the first n bytes of the two
strings from tail to head, which causes the problem. In the
_rtl8812ae_phy_set_txpower_limit(), it was originally intended to meet
this requirement by carefully designing the comparison order.
For example, "pregulation" and "pbandwidth" are compared in order of
length from small to large, first is 3 and last is 4. However, the
comparison order of "prate_section" dose not obey such order requirement,
therefore when "prate_section" is "HT", when comparing from tail to head,
it will lead to access out of bounds in _rtl8812ae_eq_n_byte(). As
mentioned above, the _rtl8812ae_eq_n_byte() has the same function as
strcmp(), so just strcmp() is enough.
Fix it by removing _rtl8812ae_eq_n_byte() and use strcmp() barely.
Although it can be fixed by adjusting the comparison order of
"prate_section", this may cause the value of "rate_section" to not be
from 0 to 5. In addition, commit "49dbd1b38dff" not only moved driver
from staging to regular tree, but also added setting txpower limit
function during the driver config phase, so the problem was introduced
by this commit.
Fixes: 49dbd1b38dff ("rtlwifi: rtl8821ae: Move driver from staging to regular tree") Signed-off-by: Li Zetao <lizetao1@huawei.com> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221212025812.1541311-1-lizetao1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There are thousands of warnings in a W=2 build from just one file:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/table.c:3788:15: warning: pointer targets in initialization of 'u8 *' {aka 'unsigned char *'} from 'char *' differ in signedness [-Wpointer-sign]
Change the types to consistently use 'const char *' for the
strings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201026213040.3889546-6-arnd@kernel.org
Stable-dep-of: 117dbeda22ec ("wifi: rtlwifi: Fix global-out-of-bounds bug in _rtl8812ae_phy_set_txpower_limit()") Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called to free and drop the SKB when
it's shutdown, so replace it with dev_kfree_skb_irq(). Compile tested
only.
Fixes: 630609394850 ("New driver: rtl8xxxu (mac80211)") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221208143517.2383424-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to call consume_skb() from hardware interrupt context
or with interrupts being disabled. So replace dev_kfree_skb() with
dev_consume_skb_irq() under spin_lock_irqsave(). Compile tested only.
Fixes: e0aa890414d9 ("Revert "iwlwifi: split the drivers for agn and legacy devices 3945/4965"") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221207144013.70210-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure to copy the flags when a bio_integrity_payload is cloned.
Otherwise per-I/O properties such as IP checksum flag will not be
passed down to the HBA driver. Since the integrity buffer is owned by
the original bio, the BIP_BLOCK_INTEGRITY flag needs to be masked off
to avoid a double free in the completion path.
Commit 8b55ac78e88d ("sched: fix goto retry in pick_next_task_rt()")
removed any path which could make pick_next_rt_entity() return NULL.
However, BUG_ON(!rt_se) in _pick_next_task_rt() (the only caller of
pick_next_rt_entity()) still checks the error condition, which can
never happen, since list_entry() never returns NULL.
Remove the BUG_ON check, and instead emit a warning in the only
possible error condition here: the queue being empty which should
never happen.
Fixes: 8b55ac78e88d ("sched: fix goto retry in pick_next_task_rt()") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Phil Auld <pauld@redhat.com> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Link: https://lore.kernel.org/r/20230128-list-entry-null-check-sched-v3-1-b1a71bd1ac6b@diag.uniroma1.it Signed-off-by: Sasha Levin <sashal@kernel.org>
`dasd_reserve_req` is allocated before `dasd_vol_info_req`, and it
also needs to be freed before the error returns, just like the other
cases in this function.
As more path events need to be handled for ECKD the current path
verification infrastructure can be reused. Rename all path verifcation
code to fit the more broadly based task of path event handling and put
the path verification in a new separate function.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 460e9bed82e4 ("s390/dasd: Fix potential memleak in dasd_eckd_init()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 48545135b9422 ("blk-mq: don't handle failure in .get_budget")
remove BLK_STS_RESOURCE return value and we only check if we can get
the budget from .get_budget() now.
Correct stale comment that ".get_budget() returns BLK_STS_NO_RESOURCE"
to ".get_budget() fails to get the budget".
Fixes: 48545135b942 ("blk-mq: don't handle failure in .get_budget") Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
For shared queues case, we will only wait on bitmap_tags if we fail to get
driver tag. However, rq could be from breserved_tags, then two problems
will occur:
1. io hung if no tag is currently allocated from bitmap_tags.
2. unnecessary wakeup when tag is freed to bitmap_tags while no tag is
freed to breserved_tags.
Wait on the bitmap which rq from to fix this.
Fixes: 01f6c5d74aad ("blk-mq: improve tag waiting setup for non-shared tags") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 06391e05d8c2e ("blk-mq: remove synchronize_rcu() from
blk_mq_del_queue_tag_set()") remove handle of TAG_SHARED in restart,
then shared_hctx_restart counted for how many hardware queues are marked
for restart is removed too.
Remove the stale comment that we still count hardware queues need restart.
Fixes: 06391e05d8c2 ("blk-mq: remove synchronize_rcu() from blk_mq_del_queue_tag_set()") Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Kemeng Shi <shikemeng@huaweicloud.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Flushes bypass the I/O scheduler and get added to hctx->dispatch
in blk_mq_sched_bypass_insert. This can happen while a kworker is running
hctx->run_work work item and is past the point in
blk_mq_sched_dispatch_requests where hctx->dispatch is checked.
The blk_mq_do_dispatch_sched call is not guaranteed to end in bounded time,
because the I/O scheduler can feed an arbitrary number of commands.
Since we have only one hctx->run_work, the commands waiting in
hctx->dispatch will wait an arbitrary length of time for run_work to be
rerun.
A similar phenomenon exists with dispatches from the software queue.
The solution is to poll hctx->dispatch in blk_mq_do_dispatch_sched and
blk_mq_do_dispatch_ctx and return from the run_work handler and let it
rerun.
Signed-off-by: Salman Qazi <sqazi@google.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: c31e76bcc379 ("blk-mq: remove stale comment for blk_mq_sched_mark_restart_hctx") Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that we have the patches ("blk-mq: In blk_mq_dispatch_rq_list()
"no budget" is a reason to kick") and ("blk-mq: Rerun dispatching in
the case of budget contention") we should no longer need the fix in
the SCSI code. Revert it, resolving conflicts with other patches that
have touched this code.
With this revert (and the two new patches) I can run the script that
was in commit fb82fd7e2b5c ("scsi: core: run queue if SCSI device
queue isn't ready and queue is idle") in a loop with no failure. If I
do this revert without the two new patches I can easily get a failure.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: c31e76bcc379 ("blk-mq: remove stale comment for blk_mq_sched_mark_restart_hctx") Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes:
scpi: sensors:compatible: 'oneOf' conditional failed, one must be fixed:
['amlogic,meson-gxbb-scpi-sensors'] is too short
'arm,scpi-sensors' was expected
The function call ida_simple_get maybe fail,we should deal with it.
And if ida_simple_get success ,it need to call ida_simple_remove also.
BTW,devm_kasprintf can handle id is zero for consistency.
Amlogic G12A devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b15cb3567724 ("arm64: dts: meson-g12a: add cpus OPP table") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Link: https://lore.kernel.org/r/20230119053031.21400-1-christianshewitt@gmail.com Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Node names should be generic and use hyphens instead of underscores to
not cause warnings. Also nodes without a reg property should not have a
unit-address. Change the scpi_dvfs node to use clock-controller as node
name without a unit address (since it does not have a reg property).
Fixes: 7aab5137e6b8 ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230111211350.1461860-7-martin.blumenstingl@googlemail.com Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Documentation/devicetree/bindings/net/ethernet-phy.yaml defines that the
node name for Ethernet PHYs should match the following pattern:
^ethernet-phy(@[a-f0-9]+)?$
Replace the underscore with a hyphen to adhere to this binding.
Fixes: a3492e48bd3f ("arm64: dts: meson: g12a: add mdio multiplexer") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230111211350.1461860-6-martin.blumenstingl@googlemail.com Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_compatible_node() returns a node pointer with refcount incremented,
we should use of_node_put() on error path.
Add missing of_node_put() to avoid refcount leak.
The commit 70fd20606f84 ("clk: gcc-qcs404: Add PCIe resets") added names
for PCIe resets, but it did not change the existing qcs404.dtsi to use
these names. Do it now and use symbol names to make it easier to check
and modify the dtsi in future.
Use spinlocks to deal with workers introducing a wrapper
asus_schedule_work(), and several spinlock checks.
Otherwise, asus_kbd_backlight_set() may schedule led->work after the
structure has been freed, causing a use-after-free.
Fixes: dd7622c7552f ("HID: asus: support backlight on USB keyboards") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Link: https://lore.kernel.org/r/20230125-hid-unregister-leds-v4-5-7860c5763c38@diag.uniroma1.it Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asus driver has a worker that may access data concurrently.
Proct the accesses using a spinlock.
Fixes: dd7622c7552f ("HID: asus: support backlight on USB keyboards") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Link: https://lore.kernel.org/r/20230125-hid-unregister-leds-v4-4-7860c5763c38@diag.uniroma1.it Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the early return on LED brightness set so that any controller
application, daemon, or desktop may set the same brightness at any stage.
This is required because many ASUS ROG keyboards will default to max
brightness on laptop resume if the LEDs were set to off before sleep.
Signed-off-by: Luke D Jones <luke@ljones.dev> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since commit 457f251335e1 ("usb: core: get config and string
descriptors for unauthorized devices") was merged in 2013, there has
been no mechanism for reallocating the rawdescriptors buffers in
struct usb_device after the initial enumeration. Before that commit,
the buffers would be deallocated when a device was deauthorized and
reallocated when it was authorized and enumerated.
This means that the locking in the read_descriptors() routine is not
needed, since the buffers it reads will never be reallocated while the
routine is running. This locking can interfere with user programs
trying to read a hub's descriptors via sysfs while new child devices
of the hub are being initialized, since the hub is locked during this
procedure.
Since the locking in read_descriptors() hasn't been needed for over
nine years, we can remove it.
Commit 226fae124b2d ("vc_screen: move load of struct vc_data pointer in
vcs_read() to avoid UAF") moved the call to vcs_vc() into the loop.
While doing this it also moved the unconditional assignment of
ret = -ENXIO;
This unconditional assignment was valid outside the loop but within it
it clobbers the actual value of ret.
To avoid this only assign "ret = -ENXIO" when actually needed.
[ Also, the 'goto unlock_out" needs to be just a "break", so that it
does the right thing when it exits on later iterations when partial
success has happened - Linus ]
Christoph Paasch reported that commit b3bf02abda10 ("inet6: Remove
inet6_destroy_sock() in sk->sk_prot->destroy().") started triggering
WARN_ON_ONCE(sk->sk_forward_alloc) in sk_stream_kill_queues(). [0 - 2]
Also, we can reproduce it by a program in [3].
In the commit, we delay freeing ipv6_pinfo.pktoptions from sk->destroy()
to sk->sk_destruct(), so sk->sk_forward_alloc is no longer zero in
inet_csk_destroy_sock().
The same check has been in inet_sock_destruct() from at least v2.6,
we can just remove the WARN_ON_ONCE(). However, among the users of
sk_stream_kill_queues(), only CAIF is not calling inet_sock_destruct().
Thus, we add the same WARN_ON_ONCE() to caif_sock_destructor().
The bpf_fib_lookup() helper does not only look up the fib (ie. route)
but it also looks up the neigh. Before returning the neigh, the helper
does not check for NUD_VALID. When a neigh state (neigh->nud_state)
is in NUD_FAILED, its dmac (neigh->ha) could be all zeros. The helper
still returns SUCCESS instead of NO_NEIGH in this case. Because of the
SUCCESS return value, the bpf prog directly uses the returned dmac
and ends up filling all zero in the eth header.
This patch checks for NUD_VALID and returns NO_NEIGH if the neigh is
not valid.
The initial value of hid->collection[].parent_idx if 0. When
Report descriptor doesn't contain "HID Collection", the value
remains as 0.
In the meanwhile, when the Report descriptor fullfill
all following conditions, it will trigger hid_apply_multiplier
function call.
1. Usage page is Generic Desktop Ctrls (0x01)
2. Usage is RESOLUTION_MULTIPLIER (0x48)
3. Contain any FEATURE items
The while loop in hid_apply_multiplier will search the top-most
collection by searching parent_idx == -1. Because all parent_idx
is 0. The loop will run forever.
There is a Report Descriptor triggerring the deadloop
0x05, 0x01, // Usage Page (Generic Desktop Ctrls)
0x09, 0x48, // Usage (0x48)
0x95, 0x01, // Report Count (1)
0x75, 0x08, // Report Size (8)
0xB1, 0x01, // Feature
projects / kernel.git / log