While working on the DP AUX bus code I found a few small things that
should be fixed. Namely the non-devm version of
of_dp_aux_populate_ep_devices() was missing an export. There was also
an extra blank line in a kerneldoc and a kerneldoc that incorrectly
documented a return value. Fix these.
val = (u64)NSEC_PER_SEC * LPC18XX_PWM_TIMER_MAX;
do_div(val, lpc18xx_pwm->clk_rate);
lpc18xx_pwm->max_period_ns = val;
is bogus because with NSEC_PER_SEC = 1000000000,
LPC18XX_PWM_TIMER_MAX = 0xffffffff and clk_rate < NSEC_PER_SEC this
overflows the (on lpc18xx (i.e. ARM32) 32 bit wide) unsigned int
.max_period_ns. This results (dependant of the actual clk rate) in an
arbitrary limitation of the maximal period. E.g. for clkrate = 333333333 (Hz) we get max_period_ns = 9 instead of 12884901897.
So make .max_period_ns an u64 and pass period and duty as u64 to not
discard relevant digits. And also make use of mul_u64_u64_div_u64()
which prevents all overflows assuming clk_rate < NSEC_PER_SEC.
So this reduces stack usage, has an improved runtime behavior because of
better pipeline usage, doesn't branch to an external function and the
generated code is a bit smaller occupying less memory.
The codesize of lpc18xx_pwm_probe() is reduced by 32 bytes.
Each devm allocations has an overhead of 24 bytes to store the related
struct devres_node additionally to the fragmentation of the allocator.
So allocating 16 struct lpc18xx_pwm_data (which only hold a single int)
adds quite some overhead. Instead put the per-channel data into the
driver data struct and allocate it in one go.
.apply() assumes the clk to be for a given PWM iff the PWM is enabled.
So make sure this is the case when .probe() completes. And in .remove()
disable the according number of times.
This fixes a clk enable/disable imbalance, if some PWMs are already running
at probe time.
Fixes: 1afcd3819818 (pwm: sifive: Add a driver for SiFive SoC PWM) Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of explicitly using PWM_SIFIVE_PWMCMP0 + pwm->hwpwm *
PWM_SIFIVE_SIZE_PWMCMP for each access to one of the PWMCMP registers,
introduce a macro that takes the hwpwm id as parameter.
For the register definition using a plain 4 instead of the cpp constant
PWM_SIFIVE_SIZE_PWMCMP is easier to read, so define the offset macro
without the constant. The latter can then be dropped as there are no
users left.
Include sys/time.h and pthread.h in tmon.h, so that types
"pthread_mutex_t" and "struct timeval tv" are known when tmon.h
references them.
Without these headers, compiling tmon against musl-libc will fail with
these errors:
In file included from sysfs.c:31:0:
tmon.h:47:8: error: unknown type name 'pthread_mutex_t'
extern pthread_mutex_t input_lock;
^~~~~~~~~~~~~~~
make[3]: *** [<builtin>: sysfs.o] Error 1
make[3]: *** Waiting for unfinished jobs....
In file included from tui.c:31:0:
tmon.h:54:17: error: field 'tv' has incomplete type
struct timeval tv;
^~
make[3]: *** [<builtin>: tui.o] Error 1
make[2]: *** [Makefile:83: tmon] Error 2
Signed-off-by: Markus Mayer <mmayer@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Acked-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Tested-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Fixes: e8658e3e2d63 ("tools/thermal: Introduce tmon, a tool for thermal subsystem") Link: https://lore.kernel.org/r/20220718031040.44714-1-f.fainelli@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang has -Wconstant-conversion by default, and the constant 0xAAAAAAAAA
(9 As) being converted to an int, which is generally 32 bits, results
in the compile warning:
clang -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/ -lpthread seccomp_bpf.c -lcap -o seccomp_bpf
seccomp_bpf.c:812:67: warning: implicit conversion from 'long' to 'int' changes value from 45812984490 to -1431655766 [-Wconstant-conversion]
int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
~~~~ ^~~~~~~~~~~
1 warning generated.
-1431655766 is the expected truncation, 0xAAAAAAAA (8 As), so use
this directly in the code to avoid the warning.
On Fri, Jun 17, 2022 at 02:08:52PM +0300, Stephane Eranian wrote:
> Some changes to the way invalid MSR accesses are reported by the
> kernel is causing some problems with messages printed on the
> console.
>
> We have seen several cases of ex_handler_msr() printing invalid MSR
> accesses once but the callstack multiple times causing confusion on
> the console.
> The problem here is that another earlier commit (5.13):
>
> d771386e4102 ("once: implement DO_ONCE_LITE for non-fast-path "do once" functionality")
>
> Modifies all the pr_*_once() calls to always return true claiming
> that no caller is ever checking the return value of the functions.
>
> This is why we are seeing the callstack printed without the
> associated printk() msg.
Extract the ONCE_IF(cond) part into __ONCE_LTE_IF() and use that to
implement DO_ONCE_LITE_IF() and fix the extable code.
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes: 3dc8fc879e57 ("sched: Migrate sched to use new tick dependency mask model") Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <vschneid@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The arm_spe_pmu driver will enable SYS_PMSCR_EL1.CX in order to add CONTEXT
packets into the traces, if the owner of the perf event runs with required
capabilities i.e CAP_PERFMON or CAP_SYS_ADMIN via perfmon_capable() helper.
The value of this bit is computed in the arm_spe_event_to_pmscr() function
but the check for capabilities happens in the pmu event init callback i.e
arm_spe_pmu_event_init(). This suggests that the value of the CX bit should
remain consistent for the duration of the perf session.
However, the function arm_spe_event_to_pmscr() may be called later during
the event start callback i.e arm_spe_pmu_start() when the "current" process
is not the owner of the perf session, hence the CX bit setting is currently
not consistent.
One way to fix this, is by caching the required value of the CX bit during
the initialization of the PMU event, so that it remains consistent for the
duration of the session. It uses currently unused 'event->hw.flags' element
to cache perfmon_capable() value, which can be referred during event start
callback to compute SYS_PMSCR_EL1.CX. This ensures consistent availability
of context packets in the trace as per event owner capabilities.
Drop BIT(SYS_PMSCR_EL1_CX_SHIFT) check in arm_spe_pmu_event_init(), because
now CX bit cannot be set in arm_spe_event_to_pmscr() with perfmon_capable()
disabled.
Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Fixes: 5a75be7e6ec9 ("drivers/perf: Add support for ARMv8.2 Statistical Profiling Extension") Reported-by: German Gomez <german.gomez@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220714061302.2715102-1-anshuman.khandual@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using a NOMAP domain, __irq_resolve_mapping() doesn't store
the Linux IRQ number at the address optionally provided by the caller.
While this isn't a huge deal (the returned value is guaranteed
to the hwirq that was passed as a parameter), let's honour the letter
of the API by writing the expected value.
Currently the DT for QCS404 SoC has setup for 2 USB2 PHYs with one each
assigned to USB3 controller and USB2 controller. This assignment is
incorrect which only works by luck: as when each USB HCI comes up it
configures the *other* controllers PHY which is enough to make them
happy. If, for any reason, we were to disable one of the controllers then
both would stop working.
This was a difficult inconsistency to be caught which was found while
trying to enable USB support in u-boot. So with all the required drivers
ported to u-boot, I couldn't get the same USB storage device enumerated
in u-boot which was being enumerated fine by the kernel.
The root cause of the problem came out to be that I wasn't enabling USB2
PHY: "usb2_phy_prim" in u-boot. Then I realised that via simply disabling
the same USB2 PHY currently assigned to USB2 host controller in the
kernel disabled enumeration for USB3 host controller as well.
So fix this inconsistency by correctly assigning USB2 PHYs.
Fixes: af153ec753ba ("arm64: dts: qcom: qcs404: Add USB devices and PHYs") Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220711083038.1518529-1-sumit.garg@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
QCOM_RPMPD requires PM_GENERIC_DOMAINS/_OF, which in turns requires
CONFIG_PM. I forgot about the latter in my earlier patch (it's still
in -next as of the time of committing, hence no Fixes: tag). Fix it.
We should call the of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: ece05fa76e95 ("regulator: of: Add support for parsing regulator_state for suspend state") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220715111027.391032-1-windhl@126.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change dm-writecache, so that it counts the number of blocks discarded
instead of the number of discard bios. Make it consistent with the
read and write statistics counters that were changed to count the
number of blocks instead of bios.
Change dm-writecache, so that it counts the number of blocks written
instead of the number of write bios. Bios can be split and requeued
using the dm_accept_partial_bio function, so counting bios caused
inaccurate results.
Change dm-writecache, so that it counts the number of blocks read
instead of the number of read bios. Bios can be split and requeued
using the dm_accept_partial_bio function, so counting bios caused
inaccurate results.
Both genpd_debug_add() and genpd_debug_remove() may be called
indirectly by other drivers while genpd_debugfs_dir is not yet
set. For example, drivers can call pm_genpd_init() in probe or
pm_genpd_init() in probe fail/cleanup path:
At this time, genpd_debug_init() may not yet be called.
genpd_debug_add() checks that if genpd_debugfs_dir is NULL, it
will return directly. Make sure this is also checked
in pm_genpd_remove(), otherwise components under debugfs root
which has the same name as other components under pm_genpd may
be accidentally removed, since NULL represents debugfs root.
Fixes: 79215baf0ddd ("PM: domains: create debugfs nodes when adding power domains") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trace the remapped operation and its flags instead of only the data
direction of remapped operations. This issue was detected by analyzing
the warnings reported by sparse related to the new blk_opf_t type.
Reviewed-by: Jun'ichi Nomura <junichi.nomura@nec.com> Cc: Mike Snitzer <snitzer@kernel.org> Cc: Mike Christie <michael.christie@oracle.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Chaitanya Kulkarni <kch@nvidia.com> Fixes: 9dbf0eab28ec ("blktrace: use op accessors") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20220714180729.1065367-11-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org Fixes: 8e55853efe1f ("hwmon: Driver for disk and solid state drives with temperature sensors") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling spi_unregister_master(), the refcount of master will
be decrease to 0, and it will be freed in spi_controller_release(),
the device data also will be freed, so it will lead a UAF when using
'tspi'. To fix this, get the master before unregister and put it when
finish using it.
Fixes: a86d2af2b098 ("spi: tegra20-slink: Don't use resource-managed spi_register helper") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220713094024.1508869-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit c5f5dc71e6eb ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes: c5f5dc71e6eb ("spi: simplify devm_spi_register_controller") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
blk_mq_debugfs_register_hctx() can be called by blk_mq_update_nr_hw_queues
when gendisk isn't added yet, such as nvme tcp.
Fixes the warning of 'debugfs: Directory 'hctx0' with parent '/' already present!'
which can be observed reliably when running blktests nvme/005.
Fixes: 08a5d58dd943 ("blk-mq: no need to check return value of debugfs_create functions") Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220711090808.259682-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Tegra SYSRAM contains regions access to which is restricted to
certain hardware blocks on the system, and speculative accesses to
those will cause issues.
Patch 'misc: sram: Only map reserved areas in Tegra SYSRAM' attempted
to resolve this by only mapping the regions specified in the device
tree on the assumption that there are no such restricted areas within
the 64K-aligned area of memory that contains the memory we wish to map.
Turns out this assumption is wrong, as there are such areas above the
4K pages described in the device trees. As such, we need to use the
bigger hammer that is no-memory-wc, which causes the memory to be
mapped as Device memory to which speculative accesses are disallowed.
As such, the previous patch in the series,
'firmware: tegra: bpmp: do only aligned access to IPC memory area',
is required with this patch to make the BPMP driver only issue aligned
memory accesses as those are also required with Device memory.
Fixes: efeafa4ddfc2 ("misc: sram: Only map reserved areas in Tegra SYSRAM") Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Reviewed-by: Yousaf Kaukab <ykaukab@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The json-schema bindings for SRAM expect the nodes to be called "sram"
rather than "sysram" or "shmem". Furthermore, place the brackets around
the SYSRAM references such that a two-element array is created rather
than a two-element array nested in a single-element array. This is not
relevant for device tree itself, but allows the nodes to be properly
validated against json-schema bindings.
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
Both the sdc2-on and sdc2-off pinctrl nodes are used by the
sdhci@4784000 node in sm6125.dtsi. Surprisingly sdc2-off is defined in
sm6125, yet its sdc2-on counterpart is only defined in board-specific DT
for the Sony Seine PDX201 board/device resulting in an "undefined label
&sdc2_state_on" error if sm6125.dtsi were included elsewhere.
This sm6125 base dtsi should not rely on externally defined labels; the
properties referencing it should then also be written externally.
Since the sdc2-on pin configuration is board-independent just like
sdc2-off, move it from seine-pdx201.dts into sm6125.dtsi.
The SDCard-detect pin (gpio98) is however board-specific, and remains as
an overwrite in seine-pdx201.dts for both the on and off state.
As a drive-by cleanup, reorder bias- and drive-strength properties.
Fixes: ceb7b4bde2c6 ("arm64: dts: qcom: Add support for SM6125") Fixes: a9bc52cf73af ("arm64: dts: qcom: sm6125: Add support for Sony Xperia 10II") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220508100336.127176-1-marijn.suijten@somainline.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently acpi_viot_init() gets called after the pci
device has been scanned and pci_enable_acs() has been called.
So pci_request_acs() fails to be taken into account leading
to wrong single iommu group topologies when dealing with
multi-function root ports for instance.
We cannot simply move the acpi_viot_init() earlier, similarly
as the IORT init because the VIOT parsing relies on the pci
scan. However we can detect VIOT is present earlier and in
such a case, request ACS. Introduce a new acpi_viot_early_init()
routine that allows to call pci_request_acs() before the scan.
While at it, guard the call to pci_request_acs() with #ifdef
CONFIG_PCI.
Fixes: c48f472e136c ("ACPI: Add driver for the VIOT table") Signed-off-by: Eric Auger <eric.auger@redhat.com> Reported-by: Jin Liu <jinl@redhat.com> Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. So, remove all the uses and add
devm_kstrdup() or devm_kasprintf() instead.
Also, modify the "for" loop conditions to clarify the access to the
st->orientation.rotation buffer.
This patch is an effort to clean up the proliferation of str*()
functions in the kernel and a previous step in the path to remove
the strcpy function from the kernel entirely [1].
From commit fc3141823997 ("ACPI / APEI: Make hest.c manage the estatus
memory pool") was merged, ghes_init() relies on acpi_hest_init() to manage
the estatus memory pool. On the other hand, ghes_init() relies on
sdei_init() to detect the SDEI version and (un)register events. The
dependencies are as follows:
HEST is not PCI-specific and initcall ordering is implicit and not
well-defined within a level.
Based on above, remove acpi_hest_init() from acpi_pci_root_init() and
convert ghes_init() and sdei_init() from initcalls to explicit calls in the
following order:
acpi_hest_init()
ghes_init()
sdei_init()
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The smem-state properties for the pronto node were incorrectly labelled,
reading `qcom,state*` rather than `qcom,smem-state*`. Fix that, allowing
the stop state to be used.
Fix the following Sparse warnings that got noticed when the PPC-dev
patchwork was checking another patch (see the link below):
init/main.c:862:1: warning: symbol 'randomize_kstack_offset' was not declared. Should it be static?
init/main.c:864:1: warning: symbol 'kstack_offset' was not declared. Should it be static?
Which in fact are triggered on all architectures that have
HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET support (for instances x86, arm64
etc).
In error case in hisi_lpc_acpi_probe() after calling platform_device_add(),
hisi_lpc_acpi_remove() can't release the failed 'pdev', so it will be leak,
call platform_device_put() to fix this problem.
I'v constructed this error case and tested this patch on D05 board.
Fixes: 7255933d7195 ("HISI LPC: Re-Add ACPI child enumeration support") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
When breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the child node.
Add missing of_node_put() to avoid refcount leak.
Fixes: aae5cf3a96d0 ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220606064252.42595-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
When a platform marks a memory range as "special purpose" it is not
onlined as System RAM by default. However, it is still suitable for
error injection. Add IORES_DESC_SOFT_RESERVED to einj_error_inject() as
a permissible memory type in the sanity checking of the arguments to
_EINJ.
Fixes: cc41424cdd4f ("x86/efi: EFI soft reservation to E820 enumeration") Reviewed-by: Tony Luck <tony.luck@intel.com> Reported-by: Omar Avelar <omar.avelar@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PM8916 device specification [1] documents a programmable range of
1.75V to 3.337V with 12.5mV steps for the PMOS LDOs in PM8916. This
range is also used when controlling the regulator directly using the
qcom_spmi-regulator driver ("ult_pldo" there).
However, for some reason the qcom_smd-regulator driver allows a much
larger range for the same hardware component. This could be simply a
typo, since the start of the range is essentially just missing a '1'.
In practice this does not cause any major problems, since the driver
just sends the actual voltage to the RPM firmware instead of making use
of the incorrect voltage selector. Still, having the wrong range there
is confusing and prevents the regulator core from validating requests
correctly.
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: e9f893733fd3 ("ARM: zynq: Add support for SOC_BUS") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220605082807.21526-1-linmq006@gmail.com Signed-off-by: Michal Simek <michal.simek@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ICC path for the GPU incorrectly states <&gnoc 1 &bimc 5>, which is
a path from SLAVE_GNOC_BIMC to SLAVE_EBI. According to the downstream
kernel sources, the GPU uses MASTER_OXILI here, which is equivalent to
<&bimc 1 ...>.
While we are at it, use defined names instead of the numbers for this
interconnect path.
The SoC's device tree file disables gpucc and adreno's SMMU by default.
So let's disable the GPU too. Moreover it looks like SMMU might be not
usable without additional patches (which means that GPU is unusable
too). No board uses GPU at this moment.
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b24c1e47f0c5 ("ARM: OMAP3+: PRM: register interrupt information from DT") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220526073724.21169-1-linmq006@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
omapdss_find_dss_of_node() calls of_find_compatible_node() to get device
node. of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in later error path and normal path.
Fixes: 9371ff71a3a5b ("drm/omap: Populate DSS children in omapdss driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220601044858.3352-1-linmq006@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Returning 0 early from __bio_iov_append_get_pages() for the
max_append_sectors warning just creates an infinite loop since 0 means
success, and the bio will never fill from the unadvancing iov_iter. We
could turn the return into an error value, but it will already be turned
into an error value later on, so just remove the warning. Clearly no one
ever hit it anyway.
Fixes: bfecb9aac701f ("block: Introduce REQ_OP_ZONE_APPEND") Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Link: https://lore.kernel.org/r/20220610195830.3574005-2-kbusch@fb.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 9a587aa2a000 ("locking/lockdep: Mark local_lock_t") added yet
another lockdep_init_map_*() variant, but forgot to update all the
existing users of the most complicated version.
This could lead to a loss of lock_type and hence an incorrect report.
Given the relative rarity of both local_lock and these annotations,
this is unlikely to happen in practise, still, best fix things.
Commit 0dd48e627da0 ("arm64: cpufeature: allow for version discrepancy in
PMU implementations") made it possible to run Linux on a machine with PMUs
with different versions without tainting the kernel. The patch relaxed the
restriction only for the ID_AA64DFR0_EL1.PMUVer field, and missed doing the
same for ID_DFR0_EL1.PerfMon , which also reports the PMU version, but for
the AArch32 state.
For example, with Linux running on two clusters with different PMU
versions, the kernel is tainted when bringing up secondaries with the
following message:
[ 0.097027] smp: Bringing up secondary CPUs ...
[..]
[ 0.142805] Detected PIPT I-cache on CPU4
[ 0.142805] CPU features: SANITY CHECK: Unexpected variation in SYS_ID_DFR0_EL1. Boot CPU: 0x00000004011088, CPU4: 0x00000005011088
[ 0.143555] CPU features: Unsupported CPU feature variation detected.
[ 0.143702] GICv3: CPU4: found redistributor 10000 region 0:0x000000002f180000
[ 0.143702] GICv3: CPU4: using allocated LPI pending table @0x00000008800d0000
[ 0.144888] CPU4: Booted secondary processor 0x0000010000 [0x410fd0f0]
The boot CPU implements FEAT_PMUv3p1 (ID_DFR0_EL1.PerfMon, bits 27:24, is
0b0100), but CPU4, part of the other cluster, implements FEAT_PMUv3p4
(ID_DFR0_EL1.PerfMon = 0b0101).
Treat the PerfMon field as FTR_NONSTRICT and FTR_EXACT to pass the sanity
check and to match how PMUVer is treated for the 64bit ID register.
Fixes: 0dd48e627da0 ("arm64: cpufeature: allow for version discrepancy in PMU implementations") Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com> Link: https://lore.kernel.org/r/20220617111332.203061-1-alexandru.elisei@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to an oversight, on arm64 lockdep IRQ state tracking doesn't work as
intended in NMI context. This demonstrably results in bogus warnings
from lockdep, and in theory could mask a variety of issues.
On arm64, we've consistently tracked IRQ flag state for NMIs (and
saved/restored the state of the interrupted context) since commit:
That commit fixed most lockdep issues with NMI by virtue of the
save/restore of the lockdep state of the interrupted context. However,
for lockdep IRQ state tracking to consistently take effect in NMI
context it has been necessary to select TRACE_IRQFLAGS_NMI_SUPPORT since
commit:
166add0845e612f3 ("locking/lockdep: Fix TRACE_IRQFLAGS vs. NMIs")
As arm64 does not select TRACE_IRQFLAGS_NMI_SUPPORT, this means that the
lockdep state can be stale in NMI context, and some uses of that state
can consume stale data.
When an NMI is taken arm64 entry code will call arm64_enter_nmi(). This
will enter NMI context via __nmi_enter() before calling
lockdep_hardirqs_off() to inform lockdep that IRQs have been masked.
Where TRACE_IRQFLAGS_NMI_SUPPORT is not selected, lockdep_hardirqs_off()
will not update lockdep state if called in NMI context. Thus if IRQs
were enabled in the original context, lockdep will continue to believe
that IRQs are enabled despite the call to lockdep_hardirqs_off().
However, the lockdep_assert_*() checks do take effect in NMI context,
and will consume the stale lockdep state. If an NMI is taken from a
context which had IRQs enabled, and during the handling of the NMI
something calls lockdep_assert_irqs_disabled(), this will result in a
spurious warning based upon the stale lockdep state.
This can be seen when using perf with GICv3 pseudo-NMIs. Within the perf
NMI handler we may attempt a uaccess to record the userspace callchain,
and is this faults the el1_abort() call in the nested context will call
exit_to_kernel_mode() when returning, which has a
lockdep_assert_irqs_disabled() assertion:
Note that as lockdep_assert_irqs_disabled() uses WARN_ON_ONCE(), and
this uses a BRK, the warning is logged with the real PSTATE at the time
of the warning, which clearly has DAIF.I set, meaning IRQs (and
pseudo-NMIs) were definitely masked and the warning is spurious.
Fix this by selecting TRACE_IRQFLAGS_NMI_SUPPORT such that the existing
entry tracking takes effect, as we had originally intended when the
arm64 entry code was fixed for transitions to/from NMI.
Arguably the lockdep_assert_*() functions should have the same NMI
checks as the rest of the code to prevent spurious warnings when
TRACE_IRQFLAGS_NMI_SUPPORT is not selected, but the real fix for any
architecture is to explicitly handle the transitions to/from NMI in the
entry code.
Fixes: 3755c7f30079 ("arm64: entry: fix NMI {user, kernel}->kernel transitions") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20220511131733.4074499-3-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The entry-method property of the idle-states node should be "psci" as
described in the idle-states binding, since this is already the value of
enable-method in the CPU nodes. Fix it to get rid of a dtbs_check
warning.
Fixes: f19622e6dc59 ("arm64: dts: mt8192: Add cpu-idle-states") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220617233150.2466344-3-nfraprado@collabora.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tweak the name of the idle-states subnodes so that they follow the
binding pattern, getting rid of dtbs_check warnings.
Only the usage of "-" in the name was necessary, but "off" was also
exchanged for "sleep" since that seems to be a more common wording in
other dts files.
Fixes: f19622e6dc59 ("arm64: dts: mt8192: Add cpu-idle-states") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220617233150.2466344-2-nfraprado@collabora.com Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/arm64/boot/dts/renesas/r8a774c0-cat874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[74], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[79], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[82], [0]] is too long
arch/arm64/boot/dts/renesas/r8a774c0-ek874-mipi-2.1.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[87], [0]] is too long
arch/arm64/boot/dts/renesas/r8a77990-ebisu.dtb: thermal-zones: cpu-thermal:thermal-sensors: [[105], [0]] is too long
From schema: Documentation/devicetree/bindings/thermal/thermal-zones.yaml
Indeed, the thermal sensors on R-Car E3 and RZ/G2E support only a single
zone, hence #thermal-sensor-cells = <0>.
Fix this by dropping the bogus zero cell from the thermal sensor
specifiers.
Fixes: c7a4f5fd2bc60408 ("arm64: dts: renesas: r8a77990: Create thermal zone to support IPA") Fixes: 6e3f93f5a94c9022 ("arm64: dts: renesas: r8a774c0: Create thermal zone to support IPA") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/28b812fdd1fc3698311fac984ab8b91d3d655c1c.1655301684.git.geert+renesas@glider.be Signed-off-by: Sasha Levin <sashal@kernel.org>
In meson_secure_pwrc_probe(), there is a refcount leak in one fail
path.
Signed-off-by: Liang He <windhl@126.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Fixes: a029119861a4 ("soc: amlogic: Add support for Secure power domains controller") Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220616144915.3988071-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 9db7f32b60b9 ("nmi_backtrace: generate one-line reports for idle cpus")
introduced a new text section called cpuidle; with that, we have a mechanism
to add idling functions in such section and skip them from nmi_backtrace
output, since they're useless and potentially flooding for such report.
Happens that inlining might cause some real idle functions to end-up
outside of such section; this is currently the case of ACPI processor_idle
driver; the functions acpi_idle_enter_* do inline acpi_idle_do_entry(),
hence they stay out of the cpuidle section.
Fix that by marking such functions to also live in the cpuidle section.
Fixes: 9db7f32b60b9 ("nmi_backtrace: generate one-line reports for idle cpus") Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 4a116d5182cf ("soc: amlogic: Add Meson6/Meson8/Meson8b/Meson8m2 SoC Information driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20220524065729.33689-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When offset is larger than the size of the bit array, we should not
attempt to access the array as we can perform an access beyond the
end of the array. Fix this by changing the pre-condition.
Using "cmp r2, r1; bhs ..." covers us for the size == 0 case, since
this will always take the branch when r1 is zero, irrespective of
the value of r2. This means we can fix this bug without adding any
additional code!
Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
With GCC 12 allmodconfig prom_init fails to build:
Error: External symbol 'memset' referenced from prom_init.c
make[2]: *** [arch/powerpc/kernel/Makefile:204: arch/powerpc/kernel/prom_init_check] Error 1
The allmodconfig build enables KASAN, so all calls to memset in
prom_init should be converted to __memset by the #ifdefs in
asm/string.h, because prom_init must use the non-KASAN instrumented
versions.
The build failure happens because there's a call to memset that hasn't
been caught by the pre-processor and converted to __memset. Typically
that's because it's a memset generated by the compiler itself, and that
is the case here.
With GCC 12, allmodconfig enables CONFIG_INIT_STACK_ALL_PATTERN, which
causes the compiler to emit memset calls to initialise on-stack
variables with a pattern.
Because prom_init is non-user-facing boot-time only code, as a
workaround just disable stack variable initialisation to unbreak the
build.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2074 Signed-off-by: xinhui pan <xinhui.pan@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GCC 12 continues to get smarter about array accesses. The KASAN tests
are expecting to explicitly test out-of-bounds conditions at run-time,
so hide the variable from GCC, to avoid warnings like:
../lib/test_kasan.c: In function 'ksize_uaf':
../lib/test_kasan.c:790:61: warning: array subscript 120 is outside array bounds of 'void[120]' [-Warray-bounds]
790 | KUNIT_EXPECT_KASAN_FAIL(test, ((volatile char *)ptr)[size]);
| ~~~~~~~~~~~~~~~~~~~~~~^~~~~~
../lib/test_kasan.c:97:9: note: in definition of macro 'KUNIT_EXPECT_KASAN_FAIL'
97 | expression; \
| ^~~~~~~~~~
In this function, it directly returns the result of __security_read_policy
without freeing the allocated memory in *data, cause memory leak issue,
so free the memory if __security_read_policy failed.
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
[PM: subject line tweak] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting hung task at misc_open() [1], for there is a race
window of AB-BA deadlock which involves probe_count variable. Currently
wait_for_device_probe() from snapshot_open() from misc_open() can sleep
forever with misc_mtx held if probe_count cannot become 0.
When a device is probed by hub_event() work function, probe_count is
incremented before the probe function starts, and probe_count is
decremented after the probe function completed.
There are three cases that can prevent probe_count from dropping to 0.
(a) A device being probed stopped responding (i.e. broken/malicious
hardware).
(b) A process emulating a USB device using /dev/raw-gadget interface
stopped responding for some reason.
(c) New device probe requests keeps coming in before existing device
probe requests complete.
The phenomenon syzbot is reporting is (b). A process which is holding
system_transition_mutex and misc_mtx is waiting for probe_count to become
0 inside wait_for_device_probe(), but the probe function which is called
from hub_event() work function is waiting for the processes which are
blocked at mutex_lock(&misc_mtx) to respond via /dev/raw-gadget interface.
This patch mitigates (b) by deferring wait_for_device_probe() from
snapshot_open() to snapshot_write() and snapshot_ioctl(). Please note that
the possibility of (b) remains as long as any thread which is emulating a
USB device via /dev/raw-gadget interface can be blocked by uninterruptible
blocking operations (e.g. mutex_lock()).
Please also note that (a) and (c) are not addressed. Regarding (c), we
should change the code to wait for only one device which contains the
image for resuming from hibernation. I don't know how to address (a), for
use of timeout for wait_for_device_probe() might result in loss of user
data in the image. Maybe we should require the userland to wait for the
image device before opening /dev/snapshot interface.
Taking a lock at the beginning of .remove() doesn't prevent new readers.
With the existing approach it can happen, that a read occurs just when
the lock was taken blocking the reader until the lock is released at the
end of the remove callback which then accessed *data that is already
freed then.
To actually fix this problem the hwmon core needs some adaption. Until
this is implemented take the optimistic approach of assuming that all
readers are gone after hwmon_device_unregister() and
sysfs_remove_group() as most other drivers do. (And once the core
implements that, taking the lock would deadlock.)
So drop the lock, move the reset to after device unregistration to keep
the device in a workable state until it's deregistered. Also add a error
message in case the reset fails and return 0 anyhow. (Returning an error
code, doesn't stop the platform device unregistration and only results
in a little helpful error message before the devm cleanup handlers are
called.)
A user reported that the program dell-bios-fan-control
worked on his Dell XPS 13 7390 to switch off automatic
fan control.
Since it uses the same mechanism as the dell_smm_hwmon
module, add this model to the fan control whitelist.
In rcar_gen2_regulator_quirk(), for_each_matching_node_and_match() will
automatically increase and decrease the refcount. However, we should
call of_node_get() for the new reference created in 'quirk->np'.
Besides, we also should call of_node_put() before the 'quirk' being
freed.
But, Lenovo G40-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Signed-off-by: Manyi Li <limanyi@uniontech.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems that these quirks are no longer necessary since
commit 1196b1f853ce ("ACPI: EC: Fix possible issues related to EC
initialization order"), which has fixed this in a generic manner.
There are 3 commits adding DMI entries with this quirk (adding multiple
DMI entries per commit). 2/3 commits are from before the generic fix.
Which leaves commit 314acc194d73 ("ACPI: EC: Make more Asus laptops
use ECDT _GPE"), which was committed way after the generic fix.
But this was just due to slow upstreaming of it. This commit stems
from Endless from 15 Aug 2017 (committed upstream 20 May 2021):
https://github.com/endlessm/linux/pull/288
The current code should work fine without this:
1. The EC_FLAGS_IGNORE_DSDT_GPE flag is only checked in ec_parse_device(),
like this:
2. ec_parse_device() is only called from acpi_ec_add() and
acpi_ec_dsdt_probe()
3. acpi_ec_dsdt_probe() starts with:
if (boot_ec)
return;
so it only calls ec_parse_device() when boot_ec == NULL, meaning that
the quirk never triggers for this call. So only the call in
acpi_ec_add() matters.
4. acpi_ec_add() does the following after the ec_parse_device() call:
if (boot_ec && ec->command_addr == boot_ec->command_addr &&
ec->data_addr == boot_ec->data_addr &&
!EC_FLAGS_TRUST_DSDT_GPE) {
/*
* Trust PNP0C09 namespace location rather than
* ECDT ID. But trust ECDT GPE rather than _GPE
* because of ASUS quirks, so do not change
* boot_ec->gpe to ec->gpe.
*/
boot_ec->handle = ec->handle;
acpi_handle_debug(ec->handle, "duplicated.\n");
acpi_ec_free(ec);
ec = boot_ec;
}
The quirk only matters if boot_ec != NULL and EC_FLAGS_TRUST_DSDT_GPE
is never set at the same time as EC_FLAGS_IGNORE_DSDT_GPE.
That means that if the addresses match we always enter this if block and
then only the ec->handle part of the data stored in ec by ec_parse_device()
is used and the rest is thrown away, after which ec is made to point
to boot_ec, at which point ec->gpe == boot_ec->gpe, so the same result
as with the quirk set, independent of the value of the quirk.
Also note the comment in this block which indicates that the gpe result
from ec_parse_device() is deliberately not taken to deal with buggy
Asus laptops and all DMI quirks setting EC_FLAGS_IGNORE_DSDT_GPE are for
Asus laptops.
Based on the above I believe that unless on some quirked laptops
the ECDT and DSDT EC addresses do not match we can drop the quirk.
I've checked dmesg output to ensure the ECDT and DSDT EC addresses match
for quirked models using https://linux-hardware.org hw-probe reports.
I've been able to confirm that the addresses match for the following
models this way: GL702VMK, X505BA, X505BP, X550VXK, X580VD.
Whereas for the following models I could find any dmesg output:
FX502VD, FX502VE, X542BA, X542BP.
Note the models without dmesg all were submitted in patches with a batch
of models and other models from the same batch checkout ok.
This, combined with that all the code adding the quirks was written before
the generic fix makes me believe that it is safe to remove this quirk now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Daniel Drake <drake@endlessos.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Somehow the "ThinkPad X1 Carbon 6th" entry ended up twice in the
struct dmi_system_id acpi_ec_no_wakeup[] array. Remove one of
the entries.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In omapdss_init_fbdev(), of_find_node_by_name() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617145803.4050918-1-windhl@126.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log