The nvme_fc_fcp_op structure describing an AEN operation is initialized with a
null request structure pointer. An FC LLDD may make a call to
nvme_fc_io_getuuid passing a pointer to an nvmefc_fcp_req for an AEN operation.
Add validation of the request structure pointer before dereference.
Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com> Reviewed-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer.
Through empirical testing it has been determined that sometimes RX SPI
transfers with DMA enabled return corrupted data. This is down to single
or even multiple bytes lost during DMA transfer from SPI peripheral to
memory. It seems the RX FIFO within the SPI peripheral can become
confused when performing bus read accesses wider than a single byte to it
during an active SPI transfer.
This patch reduces the width of individual DMA read accesses to the
RX FIFO to a single byte to mitigate that issue.
syzbot reported a data race splat between two processes trying to
update the same BPF map value via syscall on different CPUs:
BUG: KCSAN: data-race in bpf_percpu_array_update / bpf_percpu_array_update
write to 0xffffe8fffe7425d8 of 8 bytes by task 8257 on cpu 1:
bpf_long_memcpy include/linux/bpf.h:428 [inline]
bpf_obj_memcpy include/linux/bpf.h:441 [inline]
copy_map_value_long include/linux/bpf.h:464 [inline]
bpf_percpu_array_update+0x3bb/0x500 kernel/bpf/arraymap.c:380
bpf_map_update_value+0x190/0x370 kernel/bpf/syscall.c:175
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1749
bpf_map_do_batch+0x2df/0x3d0 kernel/bpf/syscall.c:4648
__sys_bpf+0x28a/0x780
__do_sys_bpf kernel/bpf/syscall.c:5241 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5239 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5239
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffffe8fffe7425d8 of 8 bytes by task 8268 on cpu 0:
bpf_long_memcpy include/linux/bpf.h:428 [inline]
bpf_obj_memcpy include/linux/bpf.h:441 [inline]
copy_map_value_long include/linux/bpf.h:464 [inline]
bpf_percpu_array_update+0x3bb/0x500 kernel/bpf/arraymap.c:380
bpf_map_update_value+0x190/0x370 kernel/bpf/syscall.c:175
generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1749
bpf_map_do_batch+0x2df/0x3d0 kernel/bpf/syscall.c:4648
__sys_bpf+0x28a/0x780
__do_sys_bpf kernel/bpf/syscall.c:5241 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5239 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5239
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x0000000000000000 -> 0xfffffff000002788
The bpf_long_memcpy is used with 8-byte aligned pointers, power-of-8 size
and forced to use long read/writes to try to atomically copy long counters.
It is best-effort only and no barriers are here since it _will_ race with
concurrent updates from BPF programs. The bpf_long_memcpy() is called from
bpf(2) syscall. Marco suggested that the best way to make this known to
KCSAN would be to use data_race() annotation.
__dma_entry_alloc_check_leak() calls into printk -> serial console
output (qcom geni) and grabs port->lock under free_entries_lock
spin lock, which is a reverse locking dependency chain as qcom_geni
IRQ handler can call into dma-debug code and grab free_entries_lock
under port->lock.
Move __dma_entry_alloc_check_leak() call out of free_entries_lock
scope so that we don't acquire serial console's port->lock under it.
Trimmed-down lockdep splat:
The existing dependency chain (in reverse order) is:
Reported-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org> Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When unmounting all the dirty buffers will be flushed and after
the last osd request is finished the last reference of the i_count
will be released. Then it will flush the dirty cap/snap to MDSs,
and the unmounting won't wait the possible acks, which will ihold
the inodes when updating the metadata locally but makes no sense
any more, of this. This will make the evict_inodes() to skip these
inodes.
If encrypt is enabled the kernel generate a warning when removing
the encrypt keys when the skipped inodes still hold the keyring:
VMCLEAR active VMCSes before any emergency reboot, not just if the kernel
may kexec into a new kernel after a crash. Per Intel's SDM, the VMX
architecture doesn't require the CPU to flush the VMCS cache on INIT. If
an emergency reboot doesn't RESET CPUs, cached VMCSes could theoretically
be kept and only be written back to memory after the new kernel is booted,
i.e. could effectively corrupt memory after reboot.
Opportunistically remove the setting of the global pointer to NULL to make
checkpatch happy.
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: William A. Kennington III <william@wkennington.com> Reviewed-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The drivers uses a mutex and I2C bus access in its PMIC EIC chip
get implementation. This means these functions can sleep and the PMIC EIC
chip should set the can_sleep property to true.
This will ensure that a warning is printed when trying to get the
value from a context that potentially can't sleep.
As per the FF-A specification: section "Usage of other memory region
attributes", in a transaction to donate memory or lend memory to a single
borrower, if the receiver is a PE or Proxy endpoint, the owner must not
specify the attributes and the relayer will return INVALID_PARAMETERS
if the attributes are set.
Let us not set the memory region attributes for MEM_LEND.
Commit 836fb30949d9 ("soc: imx8m: Enable OCOTP clock before reading the
register") added configuration to enable the OCOTP clock before
attempting to read from the associated registers.
This same kexec issue is present with the imx8m SoCs that use the
imx8mm_soc_uid function (e.g. imx8mp). This requires the imx8mm_soc_uid
function to configure the OCOTP clock before accessing the associated
registers. This change implements the same clock enable functionality
that is present in the imx8mq_soc_revision function for the
imx8mm_soc_uid function.
In order to use run_kselftest.sh the list of tests must be emitted to
populate kselftest-list.txt.
The powerpc Makefile is written to use EMIT_TESTS. But support for
EMIT_TESTS was dropped in commit d4e59a536f50 ("selftests: Use runner.sh
for emit targets"). Although prior to that commit a548de0fe8e1
("selftests: lib.mk: add test execute bit check to EMIT_TESTS") had
already broken run_kselftest.sh for powerpc due to the executable check
using the wrong path.
It can be fixed by replacing the EMIT_TESTS definitions with actual
emit_tests rules in the powerpc Makefiles. This makes run_kselftest.sh
able to run powerpc tests:
$ cd linux
$ export ARCH=powerpc
$ export CROSS_COMPILE=powerpc64le-linux-gnu-
$ make headers
$ make -j -C tools/testing/selftests install
$ grep -c "^powerpc" tools/testing/selftests/kselftest_install/kselftest-list.txt
182
Make supports passing the 'jobserver' (parallel make support) to child
invocations of make when either
1. The target command uses $(MAKE) directly
2. The command starts with '+'
This context is not passed through expansions that result in $(MAKE), so
the macros used in several places fail to pass on the jobserver context.
Warnings are also raised by the child mentioning this.
Prepend macros lines that invoke $(MAKE) with '+' to allow passing the
jobserver context to these children.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230228000709.124727-3-bgray@linux.ibm.com
Stable-dep-of: 58b33e78a317 ("selftests/powerpc: Fix emit_tests to work with run_kselftest.sh") Signed-off-by: Sasha Levin <sashal@kernel.org>
The CLEAN macro was added in 337f1e36 to prevent the
Makefile:50: warning: overriding recipe for target 'clean'
../../lib.mk:124: warning: ignoring old recipe for target 'clean'
style warnings. Expand it's use to fix another case of redefining a
target directly.
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230228000709.124727-2-bgray@linux.ibm.com
Stable-dep-of: 58b33e78a317 ("selftests/powerpc: Fix emit_tests to work with run_kselftest.sh") Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter reports that the Smatch static checker warning has found
that there is another refcount leak in the probe function. While
of_node_put() was added in one of the return paths, it should in
fact be added for ALL return paths that return an error and at driver
removal time.
Fixes: 54c03bfd094f ("power: supply: Fix refcount leak in rk817_charger_probe") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Closes: https://lore.kernel.org/linux-pm/dc0bb0f8-212d-4be7-be69-becd2a3f9a80@kili.mountain/ Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Link: https://lore.kernel.org/r/20230920145644.57964-1-macroalpha82@gmail.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add function prototype for gunzip() to the boot library code and make
exit() and zalloc() static.
arch/xtensa/boot/lib/zmem.c:8:6: warning: no previous prototype for 'exit' [-Wmissing-prototypes]
8 | void exit (void)
arch/xtensa/boot/lib/zmem.c:13:7: warning: no previous prototype for 'zalloc' [-Wmissing-prototypes]
13 | void *zalloc(unsigned size)
arch/xtensa/boot/lib/zmem.c:35:6: warning: no previous prototype for 'gunzip' [-Wmissing-prototypes]
35 | void gunzip (void *dst, int dstlen, unsigned char *src, int *lenp)
Fixes: 4bedea945451 ("xtensa: Architecture support for Tensilica Xtensa Part 2") Fixes: e7d163f76665 ("xtensa: Removed local copy of zlib and fixed O= support") Suggested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even when a variant has one or more of these defines set to 1, the
multiplier code paths are not used. Change the expression so that the
correct code paths are used.
arch/xtensa/lib/umulsidi3.S:44:38: warning: "XCHAL_NO_MUL" is not defined, evaluates to 0 [-Wundef]
44 | #if defined(__XTENSA_CALL0_ABI__) && XCHAL_NO_MUL
arch/xtensa/lib/umulsidi3.S:145:38: warning: "XCHAL_NO_MUL" is not defined, evaluates to 0 [-Wundef]
145 | #if defined(__XTENSA_CALL0_ABI__) && XCHAL_NO_MUL
arch/xtensa/lib/umulsidi3.S:159:5: warning: "XCHAL_NO_MUL" is not defined, evaluates to 0 [-Wundef]
159 | #if XCHAL_NO_MUL
Fixes: 8939c58d68f9 ("xtensa: add __umulsidi3 helper") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-16-rdunlap@infradead.org> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make 2 functions static to prevent build warnings:
arch/xtensa/platforms/iss/network.c:204:16: warning: no previous prototype for 'tuntap_protocol' [-Wmissing-prototypes]
204 | unsigned short tuntap_protocol(struct sk_buff *skb)
arch/xtensa/platforms/iss/network.c:444:6: warning: no previous prototype for 'iss_net_user_timer_expire' [-Wmissing-prototypes]
444 | void iss_net_user_timer_expire(struct timer_list *unused)
Fixes: 7282bee78798 ("xtensa: Architecture support for Tensilica Xtensa Part 8") Fixes: d8479a21a98b ("xtensa: Convert timers to use timer_setup()") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20230920052139.10570-14-rdunlap@infradead.org> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When variant FSF is set, XCHAL_HAVE_DIV32 is not defined. Add default
definition for that macro to prevent build warnings:
arch/xtensa/lib/divsi3.S:9:5: warning: "XCHAL_HAVE_DIV32" is not defined, evaluates to 0 [-Wundef]
9 | #if XCHAL_HAVE_DIV32
arch/xtensa/lib/modsi3.S:9:5: warning: "XCHAL_HAVE_DIV32" is not defined, evaluates to 0 [-Wundef]
9 | #if XCHAL_HAVE_DIV32
Fixes: 173d6681380a ("xtensa: remove extra header files") Suggested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reported-by: kernel test robot <lkp@intel.com> Closes: lore.kernel.org/r/202309150556.t0yCdv3g-lkp@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This function is supposed to return 0 for success instead of returning
the val->intval. This makes it the same as the other case statements
in this function.
Fixes: 81196e2e57fc ("power: supply: ucs1002: fix some health status issues") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/687f64a4-4c6e-4536-8204-98ad1df934e5@moroto.mountain Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The uarts should be tagged with SYSC_QUIRK_SWSUP_SIDLE instead of
SYSC_QUIRK_SWSUP_SIDLE_ACT. The difference is that SYSC_QUIRK_SWSUP_SIDLE
is used to force idle target modules rather than block idle during usage.
The SYSC_QUIRK_SWSUP_SIDLE_ACT should disable autoidle and wake-up when
a target module is active, and configure autoidle and wake-up when a
target module is inactive. We are missing configuring the target module
on sysc_disable_module(), and missing toggling of the wake-up bit.
Let's fix the issue to allow uart wake-up to work.
Commit 0840242e8875 ("ARM: dts: Configure clock parent for pwm vibra")
attempted to fix the PWM settings but ended up causin an additional clock
reparenting error:
clk: failed to reparent abe-clkctrl:0060:24 to sys_clkin_ck: -22
Only timer9 is in the PER domain and can use the sys_clkin_ck clock source.
For timer8, the there is no sys_clkin_ck available as it's in the ABE
domain, instead it should use syc_clk_div_ck. However, for power
management, we want to use the always on sys_32k_ck instead.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Fixes: 0840242e8875 ("ARM: dts: Configure clock parent for pwm vibra")
Depends-on: 61978617e905 ("ARM: dts: Add minimal support for Droid Bionic xt875") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Cc: Conor Dooley <conor+dt@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Stable-dep-of: ac08bda1569b ("ARM: dts: ti: omap: motorola-mapphone: Fix abe_clkctrl warning on boot") Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix "thermal_sys: cpu_thermal: Failed to read thermal-sensors cells: -2"
error on boot for omap3/4. This is caused by wrong addressing in the dts
for bandgap sensor for single sensor instances.
Note that omap4-cpu-thermal.dtsi is shared across omap4/5 and dra7, so
we can't just change the addressing in omap4-cpu-thermal.dtsi.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Fixes: a761d517bbb1 ("ARM: dts: omap3: Add cpu_thermal zone") Fixes: 0bbf6c54d100 ("arm: dts: add omap4 CPU thermal data") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
tegra-bpmp clocks driver makes implicit conversion of signed error
code to unsigned value in recalc_rate operation. The behavior for
recalc_rate, according to it's specification, should be that "If the
driver cannot figure out a rate for this clock, it must return 0."
Fixes: ca6f2796eef7 ("clk: tegra: Add BPMP clock driver") Signed-off-by: Timo Alho <talho@nvidia.com> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Link: https://lore.kernel.org/r/20230912112951.2330497-1-cyndis@kapsi.fi Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The perf power scale value would currently be reported as bogowatts if the
platform firmware supports microwatt power scale and meets the perf major
version requirements. Fix this by populating version information in the
driver private data before the call to protocol attributes is made.
Commit feaa8baee82a ("bus: ti-sysc: Implement SoC revision handling")
created a list of SoC types searching for strings based on names
and wildcards which associates the SoC to different families.
The OMAP34xx and OMAP35xx are treated as SOC_3430 while
OMAP36xx and OMAP37xx are treated as SOC_3630, but the AM35xx
isn't listed.
The AM35xx is mostly an OMAP3430, and a later commit a12315d6d270
("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific") looks
for the SOC type and behaves in a certain way if it's SOC_3430.
This caused a regression on the AM3517 causing it to return two
errors:
ti-sysc: probe of 48318000.target-module failed with error -16
ti-sysc: probe of 49032000.target-module failed with error -16
Fix this by treating the creating SOC_AM35 and inserting it between
the SOC_3430 and SOC_3630. If it is treaed the same way as the
SOC_3430 when checking the status of sysc_check_active_timer,
the error conditions will disappear.
Fixes: a12315d6d270 ("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific") Fixes: feaa8baee82a ("bus: ti-sysc: Implement SoC revision handling") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20230906233442.270835-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The am335x-evm started producing boot errors because of subtle timing
changes:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf03c1010
...
sysc_reset from sysc_probe+0xf60/0x1514
sysc_probe from platform_probe+0x5c/0xbc
...
The fix consists in using the appropriate sleep function in sysc reset.
For flexible sleeping, fsleep is recommended. Here, sysc delay parameter
can take any value in [0 - 255] us range. As a result, fsleep() should
be used, calling udelay() for a sysc delay lower than 10 us.
Do not generate the HS front and back porch gaps, the HSA gap and
EOT packet, as per "SN65DSI83 datasheet SLLSEC1I - SEPTEMBER 2012
- REVISED OCTOBER 2020", page 22, these packets are not required.
This makes the TI SN65DSI83 bridge work with Samsung DSIM on i.MX8MN.
While commit d4a5c59a955b ("mmc: au1xmmc: force non-modular build and
remove symbol_get usage") to be built in, it can still build a kernel
without MMC support and thuse no mmc_detect_change symbol at all.
Add ifdefs to build the mmc support code in the alchemy arch code
conditional on mmc support.
Fixes: d4a5c59a955b ("mmc: au1xmmc: force non-modular build and remove symbol_get usage") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inject fault while probing mdpy.ko, if kstrdup() of create_dir() fails in
kobject_add_internal() in kobject_init_and_add() in mdev_type_add()
in parent_create_sysfs_files(), it will return 0 and probe successfully.
And when rmmod mdpy.ko, the mdpy_dev_exit() will call
mdev_unregister_parent(), the mdev_type_remove() may traverse uninitialized
parent->types[i] in parent_remove_sysfs_files(), and it will cause
below null-ptr-deref.
If mdev_type_add() fails, return the error code and kset_unregister()
to fix the issue.
Commit f98b6215d7d1 ("btrfs: extent_io: do extra check for extent buffer
read write functions") changed how we handle invalid extent buffer range
for read_extent_buffer().
Previously if the range is invalid we just set the destination to zero,
but after the patch we do nothing and error out.
This can lead to smatch static checker errors like:
fs/btrfs/print-tree.c:186 print_uuid_item() error: uninitialized symbol 'subvol_id'.
fs/btrfs/tests/extent-io-tests.c:338 check_eb_bitmap() error: uninitialized symbol 'has'.
fs/btrfs/tests/extent-io-tests.c:353 check_eb_bitmap() error: uninitialized symbol 'has'.
fs/btrfs/uuid-tree.c:203 btrfs_uuid_tree_remove() error: uninitialized symbol 'read_subid'.
fs/btrfs/uuid-tree.c:353 btrfs_uuid_tree_iterate() error: uninitialized symbol 'subid_le'.
fs/btrfs/uuid-tree.c:72 btrfs_uuid_tree_lookup() error: uninitialized symbol 'data'.
fs/btrfs/volumes.c:7415 btrfs_dev_stats_value() error: uninitialized symbol 'val'.
Fix those warnings by reverting back to the old memset() behavior.
By this we keep the static checker happy and would still make a lot of
noise when such invalid ranges are passed in.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Fixes: f98b6215d7d1 ("btrfs: extent_io: do extra check for extent buffer read write functions") Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kfd_flush_tlb_after_unmap should return true for GFX v9.4.3, to do TLB
heavyweight flush after unmapping from GPU to guarantee that the GPU
will not access pages after they have been unmapped. This also helps
improve the mapping to GPU performance.
Without this, KFD accidently flush TLB after mapping to GPU because the
vm update sequence number is increased by previous unmapping.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: edcfe22985d0 ("drm/amdkfd: Insert missing TLB flush on GFX10 and later") Signed-off-by: Sasha Levin <sashal@kernel.org>
When a function is using functions from mac80211 to free an skb then it
should do it consistently and not switch to the generic dev_kfree_skb_any
(or similar functions). Otherwise (like in the error handlers), mac80211
will will not be aware of the freed skb and thus not clean up related
information in its internal data structures.
Not doing so lead in the past to filled up structure which then prevented
new clients to connect.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Fixes: 6257c702264c ("wifi: ath11k: fix tx status reporting in encap offload mode") Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230802-ath11k-ack_status_leak-v2-2-c0af729d6229@narfation.org Signed-off-by: Sasha Levin <sashal@kernel.org>
ieee80211_tx_status() treats packets in 802.11 frame format and
tries to extract sta address from packet header. When tx encap
offload is enabled, this becomes invalid operation. Hence, switch
to using ieee80211_tx_status_ext() after filling in station
address for handling both 802.11 and 802.3 frames.
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced PKEY_TYPE_EP11_AES for the PKEY_CLR2SECK2
IOCTL to convert an AES clearkey into a securekey of this type.
Unfortunately, all PKEY_CLR2SECK2 IOCTL requests with type
PKEY_TYPE_EP11_AES return with an error (-EINVAL). Fix the handling
for PKEY_TYPE_EP11_AES in PKEY_CLR2SECK2 IOCTL, so that userspace can
convert clearkey blobs into PKEY_TYPE_EP11_AES securekey blobs.
INFO: task syz-executor.0:29056 blocked for more than 143 seconds.
Not tainted 5.15.0-rc5 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor.0 state:D stack:14632 pid:29056 ppid: 6574 flags:0x00000004
Call Trace:
__schedule+0x4a1/0x1720
schedule+0x36/0xe0
rwsem_down_write_slowpath+0x322/0x7a0
fscrypt_ioctl_set_policy+0x11f/0x2a0
__f2fs_ioctl+0x1a9f/0x5780
f2fs_ioctl+0x89/0x3a0
__x64_sys_ioctl+0xe8/0x140
do_syscall_64+0x34/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Eric did some investigation on this issue, quoted from reply of Eric:
"Well, the quality of this bug report has a lot to be desired (not on
upstream kernel, reproducer is full of totally irrelevant stuff, not
sent to the mailing list of the filesystem whose disk image is being
fuzzed, etc.). But what is going on is that f2fs_empty_dir() doesn't
consider the case of a directory with an extremely large i_size on a
malicious disk image.
Specifically, the reproducer mounts an f2fs image with a directory
that has an i_size of 14814520042850357248, then calls
FS_IOC_SET_ENCRYPTION_POLICY on it.
That results in a call to f2fs_empty_dir() to check whether the
directory is empty. f2fs_empty_dir() then iterates through all 3616826182336513 blocks the directory allegedly contains to check
whether any contain anything. i_rwsem is held during this, so
anything else that tries to take it will hang."
In order to solve this issue, let's use f2fs_get_next_page_offset()
to speed up iteration by skipping holes for all below functions:
- f2fs_empty_dir
- f2fs_readdir
- find_in_level
The way why we can speed up iteration was described in
'commit 3cf4574705b4 ("f2fs: introduce get_next_page_offset to speed
up SEEK_DATA")'.
Meanwhile, in f2fs_empty_dir(), let's use f2fs_find_data_page()
instead f2fs_get_lock_data_page(), due to i_rwsem was held in
caller of f2fs_empty_dir(), there shouldn't be any races, so it's
fine to not lock dentry page during lookuping dirents in the page.
Link: https://lore.kernel.org/lkml/536944df-a0ae-1dd8-148f-510b476e1347@kernel.org/T/ Reported-by: Wei Chen <harperchen1110@gmail.com> Cc: Eric Biggers <ebiggers@google.com> Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Stable-dep-of: d2d9bb3b6d2f ("f2fs: get out of a repeat loop when getting a locked data page") Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous values were completely bogus, and resulted in the computed
DPI ratio being much lower than reality, causing applications and UIs to
misbehave.
The new values were measured by myself with a ruler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Sam Ravnborg <sam@ravnborg.org> Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2") Cc: <stable@vger.kernel.org> # v5.8+ Link: https://lore.kernel.org/r/20230714153720.336990-1-paul@crapouillou.net Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error paths for xiic_reinit() return negative values on failure
and 0 on success - this error message therefore is triggered on
_success_ rather than failure. Correct the condition so it's only
shown on failure as intended.
Fixes: 8fa9c9388053 ("i2c: xiic: return value of xiic_reinit") Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com> Acked-by: Michal Simek <michal.simek@amd.com> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In i2c_mux_gpio_probe_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 98b2b712bc85 ("i2c: i2c-mux-gpio: Enable this driver in ACPI land") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful irq_domain_add_linear() call, it
should be undone by a corresponding irq_domain_remove(), as already done
in the remove function.
1. After send request to server, wait the response until
mid->mid_state != SUBMITTED;
2. Receive response from server, and set it to mid;
3. Set the mid state to RECEIVED;
4. Kill the process, the mid state already RECEIVED, get 0;
5. Handle and release the negotiate response;
6. UAF.
It can be easily reproduce with add some delay in [3] - [6].
Only sync call has the problem since async call's callback is
executed in cifsd process.
Add an extra state to mark the mid state to READY before wakeup the
waitter, then it can get the resp safely.
Fixes: ec637e3ffb6b ("[CIFS] Avoid extra large buffer allocation (and memcpy) in cifs_readpages") Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On no-MMU, /proc/<pid>/maps reads as an empty file. This happens because
find_vma(mm, 0) always returns NULL (assuming no vma actually contains the
zero address, which is normally the case).
To fix this bug and improve the maintainability in the future, this patch
makes the no-MMU implementation as similar as possible to the MMU
implementation.
The only remaining differences are the lack of hold/release_task_mempolicy
and the extra code to shoehorn the gate vma into the iterator.
This has been tested on top of 6.5.3 on an STM32F746.
Link: https://lkml.kernel.org/r/20230915160055.971059-2-ben.wolsieffer@hefring.com Fixes: 0c563f148043 ("proc: remove VMA rbtree use from nommu") Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Giulio Benetti <giulio.benetti@benettiengineering.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The no-MMU implementation of /proc/<pid>/map doesn't normally release
the mmap read lock, because it uses !IS_ERR_OR_NULL(_vml) to determine
whether to release the lock. Since _vml is NULL when the end of the
mappings is reached, the lock is not released.
Reading /proc/1/maps twice doesn't cause a hang because it only
takes the read lock, which can be taken multiple times and therefore
doesn't show any problem if the lock isn't released. Instead, you need
to perform some operation that attempts to take the write lock after
reading /proc/<pid>/maps. To actually reproduce the bug, compile the
following code as 'proc_maps_bug':
Without this patch, mmap() will hang and the command will never
complete.
This code was incorrectly adapted from the MMU implementation, which at
the time released the lock in m_next() before returning the last entry.
The MMU implementation has diverged further from the no-MMU version since
then, so this patch brings their locking and error handling into sync,
fixing the bug and hopefully avoiding similar issues in the future.
When users attempt to obtain the coalesce setting using the
ethtool command, current code always returns 0 for tx-usecs.
This is because I225/6 always uses a queue pair setting, hence
tx_coalesce_usecs does not return a value during the
igc_ethtool_get_coalesce() callback process. The pair queue
condition checking in igc_ethtool_get_coalesce() is removed by
this patch so that the user gets information of the value of tx-usecs.
Even if i225/6 is using queue pair setting, there is no harm in
notifying the user of the tx-usecs. The implementation of the current
code may have previously been a copy of the legacy code i210.
Since I225 has the queue pair setting enabled, tx-usecs will always adhere
to the user-set rx-usecs value. An error message will appear when the user
attempts to set the tx-usecs value for the input parameters because,
by default, they should only set the rx-usecs value.
This patch also adds the helper function to get the
previous rx coalesce value similar to tx coalesce.
How to test:
User can get the coalesce value using ethtool command.
bnxt_poll_nitroa0() invokes bnxt_rx_pkt() which can run a XDP program
which in turn can return XDP_REDIRECT. bnxt_rx_pkt() is also used by
__bnxt_poll_work() which flushes (xdp_do_flush()) the packets after each
round. bnxt_poll_nitroa0() lacks this feature.
xdp_do_flush() should be invoked before leaving the NAPI callback.
Invoke xdp_do_flush() after a redirect in bnxt_poll_nitroa0() NAPI.
Cc: Michael Chan <michael.chan@broadcom.com> Fixes: f18c2b77b2e4e ("bnxt_en: optimized XDP_REDIRECT support") Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xdp_do_flush() should be invoked before leaving the NAPI poll function
after a XDP-redirect. This is not the case if the driver leaves via
the error path (after having a redirect in one of its previous
iterations).
Invoke xdp_do_flush() also in the error path.
Cc: Arthur Kiyanovski <akiyano@amazon.com> Cc: David Arinzon <darinzon@amazon.com> Cc: Noam Dagan <ndagan@amazon.com> Cc: Saeed Bishara <saeedb@amazon.com> Cc: Shay Agroskin <shayagr@amazon.com> Fixes: a318c70ad152b ("net: ena: introduce XDP redirect implementation") Acked-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was brought up by Tetsuo that the following sequence:
write_seqlock_irqsave()
printk_deferred_enter()
could lead to a deadlock if the lockdep annotation within
write_seqlock_irqsave() triggers.
The problem is that the sequence counter is incremented before the lockdep
annotation is performed. The lockdep splat would then attempt to invoke
printk() but the reader side, of the same seqcount, could have a
tty_port::lock acquired waiting for the sequence number to become even again.
The other lockdep annotations come before the actual locking because "we
want to see the locking error before it happens". There is no reason why
seqcount should be different here.
Do the lockdep annotation first then perform the locking operation (the
sequence increment).
Fixes: 1ca7d67cf5d5a ("seqcount: Add lockdep functionality to seqcount/seqlock structures") Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20230920104627._DTHgPyA@linutronix.de Closes: https://lore.kernel.org/20230621130641.-5iueY1I@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
engine->stats is a union of execlist and guc stat objects. When execlist
specific fields are initialized, the initial state of guc stats is
affected. This results in bad busyness values when using GuC mode. Move
the execlist initialization from common code to execlist specific code.
Kyle Zeng reported that there is a race between IPSET_CMD_ADD and IPSET_CMD_SWAP
in netfilter/ip_set, which can lead to the invocation of `__ip_set_put` on a
wrong `set`, triggering the `BUG_ON(set->ref == 0);` check in it.
The race is caused by using the wrong reference counter, i.e. the ref counter instead
of ref_netlink.
In rds_rdma_cm_event_handler_cmn() check, if conn pointer exists
before dereferencing it as rdma_set_service_type() argument
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: fd261ce6a30e ("rds: rdma: update rdma transport for tos") Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe1577b ("team: add support for non-ethernet devices") Suggested-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20230918123011.1884401-1-william.xuanziyang@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. we think firmware watchdog initialization is completed
before hns3 clear the firmware interrupt source. However, firmware
initialization may not complete early.
so we add delay before hns3 clear firmware interrupt source and 5 ms delay
is enough to avoid second firmware reset interrupt.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the driver will enable unicast promisc for the function
once configure mac address fail. It's unreasonable when the failure
is caused by using same mac address with other functions. So only
enable unicast promisc when mac table full.
The device_version V3 hardware can't offload the checksum for IP in GRE
packets, but can do it for NvGRE. So default to disable the checksum and
GSO offload for GRE, but keep the ability to enable it when only using
NvGRE.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the vf cmdq is disabled, there is no need to keep these task running.
So this patch skip these task when the cmdq is disabled.
Fixes: ff200099d271 ("net: hns3: remove unnecessary work in hclgevf_main") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reading the 'spec_rstack_overflow' sysfs file can trigger an unnecessary
MSR write, and possibly even a (handled) exception if the microcode
hasn't been updated.
Avoid all that by just checking X86_FEATURE_IBPB_BRTYPE instead, which
gets set by srso_select_mitigation() if the updated microcode exists.
It's possible for interrupts to get significantly delayed to the point
that callers of intel_scu_ipc_dev_command() and friends can call the
function once, hit a timeout, and call it again while the interrupt
still hasn't been processed. This driver will get seriously confused if
the interrupt is finally processed after the second IPC has been sent
with ipc_command(). It won't know which IPC has been completed. This
could be quite disastrous if calling code assumes something has happened
upon return from intel_scu_ipc_dev_simple_command() when it actually
hasn't.
Let's avoid this scenario by simply returning -EBUSY in this case.
Hopefully higher layers will know to back off or fail gracefully when
this happens. It's all highly unlikely anyway, but it's better to be
correct here as we have no way to know which IPC the status register is
telling us about if we send a second IPC while the previous IPC is still
processing.
Cc: Prashant Malani <pmalani@chromium.org> Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Fixes: ed12f295bfd5 ("ipc: Added support for IPC interrupt mode") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230913212723.3055315-5-swboyd@chromium.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Andy discovered this bug during patch review. The 'scu' argument to this
function shouldn't be overridden by the function itself. It doesn't make
any sense. Looking at the commit history, we see that commit f57fa18583f5 ("platform/x86: intel_scu_ipc: Introduce new SCU IPC API")
removed the setting of the scu to ipcdev in other functions, but not
this one. That was an oversight. Remove this line so that we stop
overriding the scu instance that is used by this function.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Closes: https://lore.kernel.org/r/ZPjdZ3xNmBEBvNiS@smile.fi.intel.com Cc: Prashant Malani <pmalani@chromium.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Fixes: f57fa18583f5 ("platform/x86: intel_scu_ipc: Introduce new SCU IPC API") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230913212723.3055315-4-swboyd@chromium.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible for the completion in ipc_wait_for_interrupt() to timeout,
simply because the interrupt was delayed in being processed. A timeout
in itself is not an error. This driver should check the status register
upon a timeout to ensure that scheduling or interrupt processing delays
don't affect the outcome of the IPC return value.
Fix this problem by reading the status bit in all cases, regardless of
the timeout. If the completion times out, we'll assume the problem was
that the IPC_STATUS_BUSY bit was still set, but if the status bit is
cleared in the meantime we know that we hit some scheduling delay and we
should just check the error bit.
Cc: Prashant Malani <pmalani@chromium.org> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Fixes: ed12f295bfd5 ("ipc: Added support for IPC interrupt mode") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230913212723.3055315-3-swboyd@chromium.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible for the polling loop in busy_loop() to get scheduled away
for a long time.
status = ipc_read_status(scu); // status = IPC_STATUS_BUSY
<long time scheduled away>
if (!(status & IPC_STATUS_BUSY))
If this happens, then the status bit could change while the task is
scheduled away and this function would never read the status again after
timing out. Instead, the function will return -ETIMEDOUT when it's
possible that scheduling didn't work out and the status bit was cleared.
Bit polling code should always check the bit being polled one more time
after the timeout in case this happens.
Fix this by reading the status once more after the while loop breaks.
The readl_poll_timeout() macro implements all of this, and it is
shorter, so use that macro here to consolidate code and fix this.
There were some concerns with using readl_poll_timeout() because it uses
timekeeping, and timekeeping isn't running early on or during the late
stages of system suspend or early stages of system resume, but an audit
of the code concluded that this code isn't called during those times so
it is safe to use the macro.
Cc: Prashant Malani <pmalani@chromium.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Fixes: e7b7ab3847c9 ("platform/x86: intel_scu_ipc: Sleeping is fine when polling") Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230913212723.3055315-2-swboyd@chromium.org Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While adding support for parsing the redbox supervision frames, the
author added `pull_size' and `total_pull_size' to track the amount of
bytes that were pulled from the skb during while parsing the skb so it
can be reverted/ pushed back at the end.
In the process probably copy&paste error occurred and for the HSRv1 case
the ethhdr was used instead of the hsr_tag. Later the hsr_tag was used
instead of hsr_sup_tag. The later error didn't matter because both
structs have the size so HSRv0 was still working. It broke however HSRv1
parsing because struct ethhdr is larger than struct hsr_tag.
Reinstate the old pulling flow and pull first ethhdr, hsr_tag in v1 case
followed by hsr_sup_tag.
[bigeasy: commit message]
Fixes: eafaa88b3eb7 ("net: hsr: Add support for redbox supervision frames")' Suggested-by: Tristram.Ha@microchip.com Signed-off-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code calling ima_free_kexec_buffer() runs long after the memblock
allocator has already been torn down, potentially resulting in a use
after free in memblock_isolate_range().
With KASAN or KFENCE, this use after free will result in a BUG
from the idle task, and a subsequent kernel panic.
Switch ima_free_kexec_buffer() over to memblock_free_late() to avoid
that bug.
Fixes: fee3ff99bc67 ("powerpc: Move arch independent ima kexec functions to drivers/of/kexec.c") Suggested-by: Mike Rappoport <rppt@kernel.org> Signed-off-by: Rik van Riel <riel@surriel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lore.kernel.org/r/20230817135558.67274c83@imladris.surriel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Valid domain value is in range 1 to HV_PERF_DOMAIN_MAX. Current code has
check for domain value greater than or equal to HV_PERF_DOMAIN_MAX. But
the check for domain value 0 is missing.
Fix this issue by adding check for domain value 0.
Before:
# ./perf stat -v -e hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ sleep 1
Using CPUID 00800200
Control descriptor is not initialized
Error:
The sys_perf_event_open() syscall returned with 5 (Input/output error) for
event (hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/).
/bin/dmesg | grep -i perf may provide additional information.
Result from dmesg:
[ 37.819387] hv-24x7: hcall failed: [0 0x60040000 0x100 0] => ret
0xfffffffffffffffc (-4) detail=0x2000000 failing ix=0
After:
# ./perf stat -v -e hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ sleep 1
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/ event is not supported by the kernel.
failed to read counter hv_24x7/CPM_ADJUNCT_INST,domain=0,core=1/
Currently, we assume the skb is associated with a device before calling
__ip_options_compile, which is not always the case if it is re-routed by
ipvs.
When skb->dev is NULL, dev_net(skb->dev) will become null-dereference.
This patch adds a check for the edge case and switch to use the net_device
from the rtable when skb->dev is NULL.
Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure") Suggested-by: David Ahern <dsahern@kernel.org> Signed-off-by: Kyle Zeng <zengyhkyle@gmail.com> Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Cc: Vadim Fedorenko <vfedorenko@novek.ru> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an XDP redirect happens before the link is ready, that
transmission will not finish and will timeout, causing an adapter
reset. If the redirects do not stop, the adapter will not stop
resetting.
Wait for the driver to signal that there's a carrier before allowing
transmissions to proceed.
Previous code was relying that when __IGC_DOWN is cleared, the NIC is
ready to transmit as all the queues are ready, what happens is that
the carrier presence will only be signaled later, after the watchdog
workqueue has a chance to run. And during this interval (between
clearing __IGC_DOWN and the watchdog running) if any transmission
happens the timeout is emitted (detected by igc_tx_timeout()) which
causes the reset, with the potential for the infinite loop.
Fixes: 4ff320361092 ("igc: Add support for XDP_REDIRECT action") Reported-by: Ferenc Fejes <ferenc.fejes@ericsson.com> Closes: https://lore.kernel.org/netdev/0caf33cf6adb3a5bf137eeaa20e89b167c9986d5.camel@ericsson.com/ Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Ferenc Fejes <ferenc.fejes@ericsson.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ionic device supports a maximum buffer length of 16 bits (see
ionic_rxq_desc or ionic_rxq_sg_elem). When adding new buffers to
the receive rings, the function ionic_rx_fill() uses 16bit math when
calculating the number of pages to allocate for an RX descriptor,
given the interface's MTU setting. If the system PAGE_SIZE >= 64KB,
and the buf_info->page_offset is 0, the remain_len value will never
decrement from the original MTU value and the frag_len value will
always be 0, causing additional pages to be allocated as scatter-
gather elements unnecessarily.
A similar math issue exists in ionic_rx_frags(), but no failures
have been observed here since a 64KB page should not normally
require any scatter-gather elements at any legal Ethernet MTU size.
Fixes: 4b0a7539a372 ("ionic: implement Rx page reuse") Signed-off-by: David Christensen <drc@linux.vnet.ibm.com> Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
bpf_nf testcase fails on s390x: bpf_skb_ct_lookup() cannot find the entry
that was added by bpf_ct_insert_entry() within the same BPF function.
The reason is that this entry is deleted by nf_ct_gc_expired().
The CT timeout starts ticking after the CT confirmation; therefore
nf_conn.timeout is initially set to the timeout value, and
__nf_conntrack_confirm() sets it to the deadline value.
bpf_ct_insert_entry() sets IPS_CONFIRMED_BIT, but does not adjust the
timeout, making its value meaningless and causing false positives.
Fix the problem by making bpf_ct_insert_entry() adjust the timeout,
like __nf_conntrack_confirm().
If port VLAN is configured on a VF then any other VLANs on top of this VF
are broken.
During i40e_ndo_set_vf_port_vlan() call the i40e driver reset the VF and
iavf driver asks PF (using VIRTCHNL_OP_GET_VF_RESOURCES) for VF capabilities
but this reset occurs too early, prior setting of vf->info.pvid field
and because this field can be zero during i40e_vc_get_vf_resources_msg()
then VIRTCHNL_VF_OFFLOAD_VLAN capability is reported to iavf driver.
This is wrong because iavf driver should not report VLAN offloading
capability when port VLAN is configured as i40e does not support QinQ
offloading.
Fix the issue by moving VF reset after setting of vf->port_vlan_id
field.
Without this patch:
$ echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
$ ip link set enp2s0f0 vf 0 vlan 3
$ ip link set enp2s0f0v0 up
$ ip link add link enp2s0f0v0 name vlan4 type vlan id 4
$ ip link set vlan4 up
...
$ ethtool -k enp2s0f0v0 | grep vlan-offload
rx-vlan-offload: on
tx-vlan-offload: on
$ dmesg -l err | grep iavf
[1292500.742914] iavf 0000:02:02.0: Failed to add VLAN filter, error IAVF_ERR_INVALID_QP_ID
With this patch:
$ echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
$ ip link set enp2s0f0 vf 0 vlan 3
$ ip link set enp2s0f0v0 up
$ ip link add link enp2s0f0v0 name vlan4 type vlan id 4
$ ip link set vlan4 up
...
$ ethtool -k enp2s0f0v0 | grep vlan-offload
rx-vlan-offload: off [requested on]
tx-vlan-offload: off [requested on]
$ dmesg -l err | grep iavf
Fixes: f9b4b6278d51 ("i40e: Reset the VF upon conflicting VLAN configuration") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log