The clk_disable_unprepare() should be called in the error handling
of devbus_get_timing_params() and of_platform_populate(), fix it by
replacing devm_clk_get and clk_prepare_enable by devm_clk_get_enabled.
Fixes: dc3cb64720f7 ("memory: add a driver for atmel ram controllers") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221126044911.7226-1-cuigaosheng1@huawei.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clk_disable_unprepare() should be called in the error handling
of caps->has_mpddr_clk, fix it by replacing devm_clk_get and
clk_prepare_enable by devm_clk_get_enabled.
Fixes: dc3cb64720f7 ("memory: add a driver for atmel ram controllers") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221125073757.3535219-1-cuigaosheng1@huawei.com Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On newer Tegra releases, early boot SID override programming and SID
override programming during resume is handled by bootloader.
In the function tegra186_mc_program_sid() which is getting removed, SID
override register of all clients is written without checking if secure
firmware has allowed write on it or not. If write is disabled by secure
firmware then it can lead to errors coming from secure firmware and hang
in kernel boot.
Also, SID override is programmed on-demand during probe_finalize() call
of IOMMU which is done in tegra186_mc_client_sid_override() in this same
file. This function does it correctly by checking if write is permitted
on SID override register. It also checks if SID override register is
already written with correct value and skips re-writing it in that case.
APR should not fail if the service device tree node does not have
the qcom,protection-domain property, since this functionality does
not exist on older platforms such as MSM8916 and MSM8996.
Ignore -EINVAL (returned when the property does not exist) to fix
a regression on 6.2-rc1 that prevents audio from working:
qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1:
Failed to read second value of qcom,protection-domain
qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1:
Failed to add apr 3 svc
Fixes: b6916837b315 ("soc: qcom: apr: Add check for idr_alloc and of_property_read_string_index") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20221229151648.19839-3-stephan@gerhold.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename deadline_is_seq_writes() to deadline_is_seq_write() (remove the
"s" plural) to more correctly reflect the fact that this function tests
a single request, not multiple requests.
Fixes: e29793d205cb ("block: mq-deadline: Do not break sequential write streams to zoned HDDs") Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Link: https://lore.kernel.org/r/20221126025550.967914-2-damien.lemoal@opensource.wdc.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 005a591c0a14 ("octeontx2-pf: Fix lmtst ID used in aura
free") uses the get/put_cpu() to protect the usage of percpu pointer
in ->aura_freeptr() callback, but it also unnecessarily disable the
preemption for the blockable memory allocation. The commit 6078a4e4a2e6
("octeontx2-pf: Avoid use of GFP_KERNEL in atomic context") tried to
fix these sleep inside atomic warnings. But it only fix the one for
the non-rt kernel. For the rt kernel, we still get the similar warnings
like below.
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by swapper/0/1:
#0: ffff800009fc5fe8 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x24/0x30
#1: ffff000100c276c0 (&mbox->lock){+.+.}-{3:3}, at: otx2_init_hw_resources+0x8c/0x3a4
#2: ffffffbfef6537e0 (&cpu_rcache->lock){+.+.}-{2:2}, at: alloc_iova_fast+0x1ac/0x2ac
Preemption disabled at:
[<ffff800008b1908c>] otx2_rq_aura_pool_init+0x14c/0x284
CPU: 20 PID: 1 Comm: swapper/0 Tainted: G W 6.2.0-rc3-rt1-yocto-preempt-rt #1
Hardware name: Marvell OcteonTX CN96XX board (DT)
Call trace:
dump_backtrace.part.0+0xe8/0xf4
show_stack+0x20/0x30
dump_stack_lvl+0x9c/0xd8
dump_stack+0x18/0x34
__might_resched+0x188/0x224
rt_spin_lock+0x64/0x110
alloc_iova_fast+0x1ac/0x2ac
iommu_dma_alloc_iova+0xd4/0x110
__iommu_dma_map+0x80/0x144
iommu_dma_map_page+0xe8/0x260
dma_map_page_attrs+0xb4/0xc0
__otx2_alloc_rbuf+0x90/0x150
otx2_rq_aura_pool_init+0x1c8/0x284
otx2_init_hw_resources+0xe4/0x3a4
otx2_open+0xf0/0x610
__dev_open+0x104/0x224
__dev_change_flags+0x1e4/0x274
dev_change_flags+0x2c/0x7c
ic_open_devs+0x124/0x2f8
ip_auto_config+0x180/0x42c
do_one_initcall+0x90/0x4dc
do_basic_setup+0x10c/0x14c
kernel_init_freeable+0x10c/0x13c
kernel_init+0x2c/0x140
ret_from_fork+0x10/0x20
Of course, we can shuffle the get/put_cpu() to only wrap the invocation
of ->aura_freeptr() as what commit 6078a4e4a2e6 does. But there are only
two ->aura_freeptr() callbacks, otx2_aura_freeptr() and
cn10k_aura_freeptr(). There is no usage of perpcu variable in the
otx2_aura_freeptr() at all, so the get/put_cpu() seems redundant to it.
We can move the get/put_cpu() into the corresponding callback which
really has the percpu variable usage and avoid the sprinkling of
get/put_cpu() in several places.
Fixes: 005a591c0a14 ("octeontx2-pf: Fix lmtst ID used in aura free") Signed-off-by: Kevin Hao <haokexin@gmail.com> Link: https://lore.kernel.org/r/20230118071300.3271125-1-haokexin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The referenced commit changed the error code returned by the kernel
when preventing a non-established socket from attaching the ktls
ULP. Before to such a commit, the user-space got ENOTCONN instead
of EINVAL.
The existing self-tests depend on such error code, and the change
caused a failure:
RUN global.non_established ...
tls.c:1673:non_established:Expected errno (22) == ENOTCONN (107)
non_established: Test failed at step #3
FAIL global.non_established
In the unlikely event existing applications do the same, address
the issue by restoring the prior error code in the above scenario.
Note that the only other ULP performing similar checks at init
time - smc_ulp_ops - also fails with ENOTCONN when trying to attach
the ULP to a non-established socket.
Reported-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: d2df6655a5ba ("net/ulp: prevent ULP without clone op from entering the LISTEN status") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Link: https://lore.kernel.org/r/7bb199e7a93317fb6f8bf8b9b2dc71c18f337cde.1674042685.git.pabeni@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid use of GFP_ATOMIC for memory allocation, disable preemption
after all memory allocation is done.
Fixes: 005a591c0a14 ("octeontx2-pf: Fix lmtst ID used in aura free") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMU IP v13.0.4 ppt interface is shared by IP v13.0.11, they use
the different mailbox register offset. So use the specific mailbox
registers offset for v13.0.4.
Signed-off-by: Tim Huang <tim.huang@amd.com> Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by: Aaron Liu <aaron.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Therefore, replace the TYPE_ALIGN macro with the _Alignof builtin to
avoid undefined behavior. (_Alignof itself is C11 and the kernel is
built with -gnu11).
ISO C11 _Alignof is subtly different from the GNU C extension
__alignof__. Latter is the preferred alignment and _Alignof the
minimal alignment. For long long on x86 these are 8 and 4
respectively.
The macro TYPE_ALIGN's behavior matches _Alignof rather than
__alignof__.
Use a temporary variable to take full advantage of READ_ONCE() behavior.
Without this, the report (and even the test) might be out of sync with
the initial test.
Reported-by: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/lkml/Y5x7GXeluFmZ8E0E@hirez.programming.kicks-ass.net Fixes: 37f94d57a9e7 ("panic: Introduce warn_limit") Fixes: a16d3ab1fec6 ("exit: Put an upper limit on how often we can oops") Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Jann Horn <jannh@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Petr Mladek <pmladek@suse.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Marco Elver <elver@google.com> Cc: tangmeng <tangmeng@uniontech.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running "make htmldocs" shows that "/sys/kernel/oops_count" was
duplicated. This should have been "warn_count":
Warning: /sys/kernel/oops_count is defined 2 times:
./Documentation/ABI/testing/sysfs-kernel-warn_count:0
./Documentation/ABI/testing/sysfs-kernel-oops_count:0
Several run-time checkers (KASAN, UBSAN, KFENCE, KCSAN, sched) roll
their own warnings, and each check "panic_on_warn". Consolidate this
into a single function so that future instrumentation can be added in
a single location.
Cc: Marco Elver <elver@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ben Segall <bsegall@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: Valentin Schneider <vschneid@redhat.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Gow <davidgow@google.com> Cc: tangmeng <tangmeng@uniontech.com> Cc: Jann Horn <jannh@google.com> Cc: Shuah Khan <skhan@linuxfoundation.org> Cc: Petr Mladek <pmladek@suse.com> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: "Guilherme G. Piccoli" <gpiccoli@igalia.com> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Cc: kasan-dev@googlegroups.com Cc: linux-mm@kvack.org Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Marco Elver <elver@google.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Link: https://lore.kernel.org/r/20221117234328.594699-4-keescook@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many Linux systems are configured to not panic on oops; but allowing an
attacker to oops the system **really** often can make even bugs that look
completely unexploitable exploitable (like NULL dereferences and such) if
each crash elevates a refcount by one or a lock is taken in read mode, and
this causes a counter to eventually overflow.
The most interesting counters for this are 32 bits wide (like open-coded
refcounts that don't use refcount_t). (The ldsem reader count on 32-bit
platforms is just 16 bits, but probably nobody cares about 32-bit platforms
that much nowadays.)
So let's panic the system if the kernel is constantly oopsing.
The speed of oopsing 2^32 times probably depends on several factors, like
how long the stack trace is and which unwinder you're using; an empirically
important one is whether your console is showing a graphical environment or
a text console that oopses will be printed to.
In a quick single-threaded benchmark, it looks like oopsing in a vfork()
child with a very short stack trace only takes ~510 microseconds per run
when a graphical console is active; but switching to a text console that
oopses are printed to slows it down around 87x, to ~45 milliseconds per
run.
(Adding more threads makes this faster, but the actual oops printing
happens under &die_lock on x86, so you can maybe speed this up by a factor
of around 2 and then any further improvement gets eaten up by lock
contention.)
It looks like it would take around 8-12 days to overflow a 32-bit counter
with repeated oopsing on a multi-core X86 system running a graphical
environment; both me (in an X86 VM) and Seth (with a distro kernel on
normal hardware in a standard configuration) got numbers in that ballpark.
12 days aren't *that* short on a desktop system, and you'd likely need much
longer on a typical server system (assuming that people don't run graphical
desktop environments on their servers), and this is a *very* noisy and
violent approach to exploiting the kernel; and it also seems to take orders
of magnitude longer on some machines, probably because stuff like EFI
pstore will slow it down a ton if that's active.
With the introduction of PRMT in the ACPI subsystem, the EFI rts
workqueue is no longer the only caller of efi_call_virt_pointer() in the
kernel. This means the EFI runtime services lock is no longer sufficient
to manage concurrent calls into firmware, but also that firmware calls
may occur that are not marshalled via the workqueue mechanism, but
originate directly from the caller context.
For added robustness, and to ensure that the runtime services have 8 KiB
of stack space available as per the EFI spec, introduce a spinlock
protected EFI runtime stack of 8 KiB, where the spinlock also ensures
serialization between the EFI rts workqueue (which itself serializes EFI
runtime calls) and other callers of efi_call_virt_pointer().
While at it, use the stack pivot to avoid reloading the shadow call
stack pointer from the ordinary stack, as doing so could produce a
gadget to defeat it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug occours due to a misuse of `attr` variable instead of `attr_b`.
`attr` is being initialized as NULL, then being derenfernced
as `attr->res.data_size`.
This bug causes a crash of the ntfs3 driver itself,
If compiled directly to the kernel, it crashes the whole system.
Signed-off-by: Alon Zahavi <zahavi.alon@gmail.com> Co-developed-by: Tal Lossos <tallossos@gmail.com> Signed-off-by: Tal Lossos <tallossos@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To work around some Window servers that return
STATUS_OBJECT_NAME_INVALID on query infos under DFS namespaces that
contain non-ASCII characters, we started checking for -ENOENT on every
file open, and if so, then send additional requests to figure out
whether it is a DFS link or not. It means that all those requests
will be sent to every non-existing file.
So, in order to reduce the number of roundtrips, check earlier whether
status code is STATUS_OBJECT_NAME_INVALID and tcon supports dfs, and
if so, then map -ENOENT to -EREMOTE so mount or automount will take
care of chasing the DFS link -- if it isn't an DFS link, then -ENOENT
will be returned appropriately.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The YCC conversion matrix for RGB -> COLOR_SPACE_YCBCR2020_TYPE is
missing the values for the fourth column of the matrix.
The fourth column of the matrix is essentially just a value that is
added given that the color is 3 components in size.
These values are needed to bias the chroma from the [-1, 1] -> [0, 1]
range.
This fixes color being very green when using Gamescope HDR on HDMI
output which prefers YCC 4:4:4.
Fixes: 3dc71226db7c ("drm/amd/display: color space ycbcr709 support") Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Joshua Ashton <joshua@froggi.es> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code in get_output_color_space depends on knowing the pixel encoding to
determine whether to pick between eg. COLOR_SPACE_SRGB or
COLOR_SPACE_YCBCR709 for transparent RGB -> YCbCr 4:4:4 in the driver.
v2: Fixed patch being accidentally based on a personal feature branch, oops!
Fixes: 944157e64c4f ("drm/amd/display: Reduce HDMI pixel encoding if max clock is exceeded") Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Joshua Ashton <joshua@froggi.es> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
Setting scaling does not correctly update CRTC state. As a result
dc stream state's src (composition area) && dest (addressable area)
was not calculated as expected. This causes set scaling doesn's work.
[How]
Correctly update CRTC state when setting scaling property.
Always allow switching away via vga-switcheroo if the display is
uninitalized. Instead prevent switching to i915 if the device has
not been initialized.
This issue was introduced by commit 2d14f3bb1f54 ("drm/i915: skip
display initialization when there is no display") protected, which
protects code paths from being executed on uninitialized devices.
In the case of vga-switcheroo, we want to allow a switch away from
i915's device. So run vga_switcheroo_process_delayed_switch() and
test in the switcheroo callbacks if the i915 device is available.
While compile-testing randconfig builds for the upcoming boardfile
removal, I noticed that an earlier patch of mine was completely
broken, and the introduction of CONFIG_ARCH_OMAP1_ANY only replaced
one set of build failures with another one, now resulting in
link failures like
ld: drivers/video/fbdev/omap/omapfb_main.o: in function `omapfb_do_probe':
drivers/video/fbdev/omap/omapfb_main.c:1703: undefined reference to `omap_set_dma_priority'
ld: drivers/dma/ti/omap-dma.o: in function `omap_dma_free_chan_resources':
drivers/dma/ti/omap-dma.c:777: undefined reference to `omap_free_dma'
drivers/dma/ti/omap-dma.c:1685: undefined reference to `omap_get_plat_info'
ld: drivers/usb/gadget/udc/omap_udc.o: in function `next_in_dma':
drivers/usb/gadget/udc/omap_udc.c:820: undefined reference to `omap_get_dma_active_status'
I tried reworking it, but the resulting patch ended up much bigger than
simply avoiding the original problem of unused-function warnings like
As a result, revert the previous fix, and rearrange the code that
produces warnings to hide them. For mcbsp, the #ifdef check can
simply be removed as the cpu_is_omapxxx() checks already achieve
the same result, while in the io.c the easiest solution appears to
be to merge the common map bits into each soc specific portion.
This gets cleaned in a nicer way after omap7xx support gets dropped,
as the remaining SoCs all have the exact same I/O map.
Fixes: c4b148419013 ("ARM: omap1: fix build with no SoC selected") Cc: stable@vger.kernel.org Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vmci_dispatch_dgs() tasklet function calls vmci_read_data()
which uses wait_event() resulting in invalid sleep in an atomic
context (and therefore potentially in a deadlock).
Use threaded irqs to fix this issue and completely remove usage
of tasklets.
Unconditional call to mei_cl_unlink in mei_cl_bus_dev_release leads
to call of the mei_cl_unlink without corresponding mei_cl_link.
This leads to miscalculation of open_handle_count (decrease without
increase).
Call unlink in mei_cldev_enable fail path and remove blanket unlink
from mei_cl_bus_dev_release.
Fixes: fbd6e656d677 ("mei: bus: need to unlink client before freeing") Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Reviewed-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20221212220247.286019-1-tomas.winkler@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can get EFI variables without fetching the attribute, so we must
allow for that in gsmi.
commit 8fb264d37a06 ("efi: pstore: Omit efivars caching EFI varstore
access layer") added a new get_variable call with attr=NULL, which
triggers panic in gsmi.
This patch:
* Adds IDs to recognize 7xxxC cards from Sealevel Systems.
* Updates exar_pci_probe() to set nr_ports to last two bytes of primary
dev ID for these cards.
Commit f8d942c54b13 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: f8d942c54b13 ("serial: core: remove baud_rates when serial console setup") Cc: stable <stable@kernel.org> Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> Acked-by: Richard Genoud <richard.genoud@gmail.com> Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode the transmission of a high priority character fails since it
is written to the data register before the transmitter is enabled. Fix this
in pl011_tx_chars() by enabling RS485 transmission before writing the
character.
On driver unload any pending descriptors are flushed and pending
DMA descriptors are explicitly completed:
idxd_dmaengine_drv_remove() ->
drv_disable_wq() ->
idxd_wq_free_irq() ->
idxd_flush_pending_descs() ->
idxd_dma_complete_txd()
With this done during driver unload any remaining descriptor is
likely stuck and can be dropped. Even so, the descriptor may still
have a callback set that could no longer be accessible. An
example of such a problem is when the dmatest fails and the dmatest
module is unloaded. The failure of dmatest leaves descriptors with
dma_async_tx_descriptor::callback pointing to code that no longer
exist. This causes a page fault as below at the time the IDXD driver
is unloaded when it attempts to run the callback:
BUG: unable to handle page fault for address: ffffffffc0665190
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
Fix this by clearing the callback pointers on the transmit
descriptors only when workqueue is disabled.
Fixes: 3551e061b85e ("dmaengine: idxd: change MSIX allocation based on per wq activation") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Fenghua Yu <fenghua.yu@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/37d06b772aa7f8863ca50f90930ea2fd80b38fc3.1670452419.git.reinette.chatre@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On driver unload any pending descriptors are flushed at the
time the interrupt is freed:
idxd_dmaengine_drv_remove() ->
drv_disable_wq() ->
idxd_wq_free_irq() ->
idxd_flush_pending_descs().
If there are any descriptors present that need to be flushed this
flow triggers a "not present" page fault as below:
BUG: unable to handle page fault for address: ff391c97c70c9040
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
The address that triggers the fault is the address of the
descriptor that was freed moments earlier via:
drv_disable_wq()->idxd_wq_free_resources()
Fix the use after free by freeing the descriptors after any possible
usage. This is done after idxd_wq_reset() to ensure that the memory
remains accessible during possible completion writes by the device.
The workqueue is enabled when the appropriate driver is loaded and
disabled when the driver is removed. When the driver is removed it
assumes that the workqueue was enabled successfully and proceeds to
free allocations made during workqueue enabling.
Failure during workqueue enabling does not prevent the driver from
being loaded. This is because the error path within drv_enable_wq()
returns success unless a second failure is encountered
during the error path. By returning success it is possible to load
the driver even if the workqueue cannot be enabled and
allocations that do not exist are attempted to be freed during
driver remove.
Some examples of problematic flows:
(a)
idxd_dmaengine_drv_probe() -> drv_enable_wq() -> idxd_wq_request_irq():
In above flow, if idxd_wq_request_irq() fails then
idxd_wq_unmap_portal() is called on error exit path, but
drv_enable_wq() returns 0 because idxd_wq_disable() succeeds. The
driver is thus loaded successfully.
idxd_dmaengine_drv_remove()->drv_disable_wq()->idxd_wq_unmap_portal()
Above flow on driver unload triggers the WARN in devm_iounmap() because
the device resource has already been removed during error path of
drv_enable_wq().
(b)
idxd_dmaengine_drv_probe() -> drv_enable_wq() -> idxd_wq_request_irq():
In above flow, if idxd_wq_request_irq() fails then
idxd_wq_init_percpu_ref() is never called to initialize the percpu
counter, yet the driver loads successfully because drv_enable_wq()
returns 0.
idxd_dmaengine_drv_remove()->__idxd_wq_quiesce()->percpu_ref_kill():
Above flow on driver unload triggers a BUG when attempting to drop the
initial ref of the uninitialized percpu ref:
BUG: kernel NULL pointer dereference, address: 0000000000000010
Fix the drv_enable_wq() error path by returning the original error that
indicates failure of workqueue enabling. This ensures that the probe
fails when an error is encountered and the driver remove paths are only
attempted when the workqueue was enabled successfully.
ldma_cfg_init() will parse DT to retrieve certain configs.
However, that is called before ldma_dma_init_vXX(), which
will make some initialization to channel configs. It will
thus incorrectly overwrite certain configs that are declared
in DT.
To fix that, we move DT parsing after initialization.
Function name is renamed to better represent what it does.
A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().
To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.
After commit fa74a191e79e ("clk: imx8mp: fix usb_root_clk parent"),
usb_root_clk is no longer for suspend clock so update dts accordingly
to use right bus clock and suspend clock.
Fixes: ca3e78ec2ea8 ("arm64: dtsi: imx8mp: add usb nodes") Cc: stable@vger.kernel.org # 93045bb787f9: clk: imx: imx8mp: add shared clk gate for usb suspend clk Cc: stable@vger.kernel.org # v5.19+ Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 99e79fc88a0c ("usb-storage: Add Hiksemi USB3-FW to IGNORE_UAS")
blacklists UAS for all of RTL9210 enclosures.
The RTL9210 controller was advertised with UAS since its release back in
2019 and was shipped with a lot of enclosure products with different
firmware combinations.
Blacklist UAS only for HIKSEMI MD202.
This should hopefully be replaced with more robust method than just
comparing strings. But with limited information [1] provided thus far
(dmesg when the device is plugged in, which includes manufacturer and
product, but no lsusb -v to compare against), this is the best we can do
for now.
Which I believe disassembles to (I don't know ARM assembly, but it looks sane enough to me...):
// halfword (16-bit) store presumably to event->wLength (at offset 6 of struct usb_cdc_notification)
0B 0D 00 79 strh w11, [x8, #6]
// word (32-bit) store presumably to req->Length (at offset 8 of struct usb_request)
6C 0A 00 B9 str w12, [x19, #8]
// x10 (NULL) was read here from offset 0 of valid pointer x9
// IMHO we're reading 'cdev->gadget' and getting NULL
// gadget is indeed at offset 0 of struct usb_composite_dev
2A 01 40 F9 ldr x10, [x9]
// loading req->buf pointer, which is at offset 0 of struct usb_request
69 02 40 F9 ldr x9, [x19]
// x10 is null, crash, appears to be attempt to read cdev->gadget->max_speed
4B 5D 40 B9 ldr w11, [x10, #0x5c]
which seems to line up with ncm_do_notify() case NCM_NOTIFY_SPEED code fragment:
/* SPEED_CHANGE data is up/down speeds in bits/sec */
data = req->buf + sizeof *event;
data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget));
My analysis of registers and NULL ptr deref crash offset
(Unable to handle kernel NULL pointer dereference at virtual address 000000000000005c)
heavily suggests that the crash is due to 'cdev->gadget' being NULL when executing:
data[0] = cpu_to_le32(ncm_bitrate(cdev->gadget));
which calls:
ncm_bitrate(NULL)
which then calls:
gadget_is_superspeed(NULL)
which reads
((struct usb_gadget *)NULL)->max_speed
and hits a panic.
AFAICT, if I'm counting right, the offset of max_speed is indeed 0x5C.
(remember there's a GKI KABI reservation of 16 bytes in struct work_struct)
It's not at all clear to me how this is all supposed to work...
but returning 0 seems much better than panic-ing...
Cc: Felipe Balbi <balbi@kernel.org> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Carlos Llamas <cmllamas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Maciej Żenczykowski <maze@google.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20230117131839.1138208-1-maze@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the problem by using the gadget name as a suffix
to each configfs_gadget's driver name, thus making the names
distinct.
Fixes: 49fdfe0d7d24 ("USB: gadget: Add a new bus for gadgets") Cc: stable <stable@kernel.org> Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com> Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Frank Li <frank.li@nxp.com> Link: https://lore.kernel.org/r/20230111065105.29205-1-chanh@os.amperecomputing.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the color matching descriptor is only sent across the wire
a single time, following the descriptors for each format and frame.
According to the UVC 1.5 Specification 3.9.2.6 ("Color Matching
Descriptors"):
"Only one instance is allowed for a given format and if present,
the Color Matching descriptor shall be placed following the Video
and Still Image Frame descriptors for that format".
Add another reference to the color matching descriptor after the
yuyv frames so that it's correctly transmitted for that format
too.
Commit 19abed8fcd95 ("usb: typec: altmodes/displayport: correct pin
assignment for UFP receptacles") fixed the pin assignment calculation
to take into account whether the peripheral was a plug or a receptacle.
But the "pin_assignments" sysfs logic was not updated. Address this by
using the macros introduced in the aforementioned commit in the sysfs
logic too.
There's the altmode re-registeration issue after data role
swap (DR_SWAP).
Comparing to USBPD 2.0, in USBPD 3.0, it loose the limit that only DFP
can initiate the VDM command to get partner identity information.
For a USBPD 3.0 UFP device, it may already get the identity information
from its port partner before DR_SWAP. If DR_SWAP send or receive at the
mean time, 'send_discover' flag will be raised again. It causes discover
identify action restart while entering ready state. And after all
discover actions are done, the 'tcpm_register_altmodes' will be called.
If old altmode is not unregistered, this sysfs create fail can be found.
In 'DR_SWAP_CHANGE_DR' state case, only DFP will unregister altmodes.
For UFP, the original altmodes keep registered.
This patch fix the logic that after DR_SWAP, 'tcpm_unregister_altmodes'
must be called whatever the current data role is.
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com> Fixes: 6cc42660aa3f ("usb: typec: Group all TCPCI/TCPM code together") Reported-by: TommyYl Chen <tommyyl.chen@mediatek.com> Cc: stable@vger.kernel.org Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/1673248790-15794-1-git-send-email-cy_huang@richtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before calling platform_get_resource() in omap2430_probe(), the 'ret' is
re-assgined to 0, it can't return an error code, if platform_get_resource
fails. Set the error code to -EINVAL to fix this.
Commit 78e134fb66b5 ("drivers:usb:fsl:Make fsl ehci drv an independent
driver module") changed DRV_NAME which was used for MODULE_ALIAS as well.
Starting from this the module alias didn't match the platform device
name created in fsl-mph-dr-of.c
Change DRV_NAME to match the driver name for host mode in fsl-mph-dr-of.
This is needed for module autoloading on ls1021a.
After doorbell DMA fetches the TRB. If during dequeuing request
driver changes NORMAL TRB to LINK TRB but doesn't delete it from
controller cache then controller will handle cached TRB and packet
can be lost.
The example scenario for this issue looks like:
1. queue request - set doorbell
2. dequeue request
3. send OUT data packet from host
4. Device will accept this packet which is unexpected
5. queue new request - set doorbell
6. Device lost the expected packet.
By setting DFLUSH controller clears DRDY bit and stop DMA transfer.
The syzbot fuzzer and Gerald Lee have identified a use-after-free bug
in the gadgetfs driver, involving processes concurrently mounting and
unmounting the gadgetfs filesystem. In particular, gadgetfs_fill_super()
can race with gadgetfs_kill_sb(), causing the latter to deallocate
the_device while the former is using it. The output from KASAN says,
in part:
BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline]
BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline]
BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline]
BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689
MPTCP protocol supports having subflows in both IPv4 and IPv6. In Linux,
it is possible to have that if the MPTCP socket has been created with
AF_INET6 family without the IPV6_V6ONLY option.
Here, a new IPv4 subflow is being added to the initial IPv6 connection,
then being removed using Netlink commands.
Cc: stable@vger.kernel.org # v5.19+ Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an MPTCP socket has been created with AF_INET6 and the IPV6_V6ONLY
option has been set, the userspace PM would allow creating subflows
using IPv4 addresses, e.g. mapped in v6.
The kernel side of userspace PM will also accept creating subflows with
local and remote addresses having different families. Depending on the
subflow socket's family, different behaviours are expected:
- If AF_INET is forced with a v6 address, the kernel will take the last
byte of the IP and try to connect to that: a new subflow is created
but to a non expected address.
- If AF_INET6 is forced with a v4 address, the kernel will try to
connect to a v4 address (v4-mapped-v6). A -EBADF error from the
connect() part is then expected.
It is then required to check the given families can be accepted. This is
done by using a new helper for addresses family matching, taking care of
IPv4 vs IPv4-mapped-IPv6 addresses. This helper will be re-used later by
the in-kernel path-manager to use mixed IPv4 and IPv6 addresses.
While at it, a clear error message is now reported if there are some
conflicts with the families that have been passed by the userspace.
Let the caller specify the to-be-created subflow family.
For a given MPTCP socket created with the AF_INET6 family, the current
userspace PM can already ask the kernel to create subflows in v4 and v6.
If "plain" IPv4 addresses are passed to the kernel, they are
automatically mapped in v6 addresses "by accident". This can be
problematic because the userspace will need to pass different addresses,
now the v4-mapped-v6 addresses to destroy this new subflow.
On the other hand, if the MPTCP socket has been created with the AF_INET
family, the command to create a subflow in v6 will be accepted but the
result will not be the one as expected as new subflow will be created in
IPv4 using part of the v6 addresses passed to the kernel: not creating
the expected subflow then.
No functional change intended for the in-kernel PM where an explicit
enforcement is currently in place. This arbitrary enforcement will be
leveraged by other patches in a future version.
A previous commit fixed a poll race that can occur, but it's only
applicable for multishot requests. For a multishot request, we can safely
ignore a spurious wakeup, as we never leave the waitqueue to begin with.
A blunt reissue of a multishot armed request can cause us to leak a
buffer, if they are ring provided. While this seems like a bug in itself,
it's not really defined behavior to reissue a multishot request directly.
It's less efficient to do so as well, and not required to rearm anything
like it is for singleshot poll requests.
The revert of the removal of this driver happened after we fixed up
the split limits for NOWAIT issue, hence it got missed. Ensure that
we check for a NULL bio after splitting, in case it should be retried.
Marking this as fixing both commits, so that stable backport will do
this correctly.
syzkaller:~# modprobe speakup_audptr
input: Speakup as /devices/virtual/input/input4
initialized device: /dev/synth, node (MAJOR 10, MINOR 125)
speakup 3.1.6: initialized
synth name on entry is: (null)
synth probe
spk_ttyio_initialise_ldisc failed because tty_kopen_exclusive returned
failed (errno -16), then remove the module, we will get a null-ptr-defer
problem, as follow:
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
When changing the ebpf program put() routines to support being called
from within IRQ context the program ID was reset to zero prior to
calling the perf event and audit UNLOAD record generators, which
resulted in problems as the ebpf program ID was bogus (always zero).
This patch addresses this problem by removing an unnecessary call to
bpf_prog_free_id() in __bpf_prog_offload_destroy() and adjusting
__bpf_prog_put() to only call bpf_prog_free_id() after audit and perf
have finished their bpf program unload tasks in
bpf_prog_put_deferred(). For the record, no one can determine, or
remember, why it was necessary to free the program ID, and remove it
from the IDR, prior to executing bpf_prog_put_deferred();
regardless, both Stanislav and Alexei agree that the approach in this
patch should be safe.
It is worth noting that when moving the bpf_prog_free_id() call, the
do_idr_lock parameter was forced to true as the ebpf devs determined
this was the correct as the do_idr_lock should always be true. The
do_idr_lock parameter will be removed in a follow-up patch, but it
was kept here to keep the patch small in an effort to ease any stable
backports.
I also modified the bpf_audit_prog() logic used to associate the
AUDIT_BPF record with other associated records, e.g. @ctx != NULL.
Instead of keying off the operation, it now keys off the execution
context, e.g. '!in_irg && !irqs_disabled()', which is much more
appropriate and should help better connect the UNLOAD operations with
the associated audit state (other audit records).
Cc: stable@vger.kernel.org Fixes: dcd27dac7033 ("bpf: Prepare bpf_prog_put() to be called from irq context.") Reported-by: Burn Alting <burn.alting@iinet.net.au> Reported-by: Jiri Olsa <olsajiri@gmail.com> Suggested-by: Stanislav Fomichev <sdf@google.com> Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Acked-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/r/20230106154400.74211-1-paul@paul-moore.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 32-bit memory resource is needed for non-prefetchable memory
allocations on the PCIe bus, however with some cards (such as the
SM768) the system fails to allocate memory from this.
Checking the allocation against the datasheet, it looks like there
has been a mis-calcualation of the resource for the first memory
region (0x0060090000..0x0070ffffff) which in the data-sheet for
the fu740 (v1p2) is from 0x0060000000..0x007fffffff. Changing
this to allocate from 0x0060090000..0x007fffffff fixes the probing
issues.
Fixes: 6d7a44491e02 ("riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC") Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Greentime Hu <greentime.hu@sifive.com> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Cc: stable@vger.kernel.org Tested-by: Ron Economos <re@w6rz.net> # from IRC Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot call PM runtime functions in tb_retimer_scan() because it will
also be called when retimers are scanned from userspace (happens when
there is no device connected on ChromeOS for instance) and at the same
USB4 port runtime resume hook. This leads to hang because neither can
proceed.
Fix this by runtime resuming USB4 ports in tb_scan_port() instead. This
makes sure the ports are runtime PM active when retimers are added under
it while avoiding the reported hang as well.
Reported-by: Utkarsh Patel <utkarsh.h.patel@intel.com> Fixes: b9cd2087420e ("thunderbolt: Runtime resume USB4 port when retimers are scanned") Cc: stable@vger.kernel.org Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log