For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.
Amend the setup accordingly.
Fixes: a4929aa7a5a7 ("drm/vc4: Add support for feeding DSI encoders from the pixel valve.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-14-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 98772f8ef2f2 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Display drivers so far need to have a lot of boilerplate to first
retrieve either the panel or bridge that they are connected to using
drm_of_find_panel_or_bridge(), and then either deal with each with ad-hoc
functions or create a drm panel bridge through drm_panel_bridge_add.
In order to reduce the boilerplate and hopefully create a path of least
resistance towards using the DRM panel bridge layer, let's create the
function devm_drm_of_get_bridge() to reduce that boilerplate.
The current plane margin calculation code clips the right and bottom
edges of the range based using the left and top margins.
This is obviously wrong, so let's fix it.
Fixes: 188f608deb8f ("drm/vc4: Take margin setup into account when updating planes") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-6-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Fixes: 91c5f61694f7 ("drm/vc4: Add support for scaling of display planes.") Signed-off-by: Dom Cobley <popcornmix@gmail.com> Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
video_device_alloc() allocates memory for vdev,
when video_register_device() fails, it doesn't release the memory and
leads to memory leak, call video_device_release() to fix this.
Fixes: 4013ca76ea36 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.
Fixes: 0db7fdbfe2fe ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device") Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Every iteration of for_each_available_child_of_node() decrements
the reference counter of the previous node. There is no decrement
when break out from the loop and results in refcount leak.
Add missing of_node_put() to fix this.
As mipi_dsi_driver_register could return error if fails,
it should be better to check the return value and return error
if fails.
Moreover, if i2c_add_driver fails, mipi_dsi_driver_register
should be reverted.
On shutdown, each CCP device instance performs shutdown processing.
However, __sev_platform_shutdown_locked() uses the controlling psp
structure to obtain the pointer to the sev_device structure. However,
during driver initialization, it is possible that an error can be received
from the firmware that results in the sev_data pointer being cleared from
the controlling psp structure. The __sev_platform_shutdown_locked()
function does not check for this situation and will segfault.
While not common, this scenario should be accounted for. Add a check for a
NULL sev_device structure before attempting to use it.
Fixes: 9ad48cb6c76c ("crypto: ccp - shutdown SEV firmware on kexec") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The prototype of .features is netdev_features_t, it should use
NETIF_F_LLTX and NETIF_F_HW_VLAN_STAG_TX, not NETIF_F_LLTX_BIT
and NETIF_F_HW_VLAN_STAG_TX_BIT.
The RCU priority boosting can fail in two situations:
1) If (nr_cpus= > maxcpus=), which means if the total number of CPUs
is higher than those brought online at boot, then torture_onoff() may
later bring up CPUs that weren't online on boot. Now since rcutorture
initialization only boosts the ksoftirqds of the CPUs that have been
set online on boot, the CPUs later set online by torture_onoff won't
benefit from the boost, making RCU priority boosting fail.
2) The ksoftirqd kthreads are boosted after the creation of
rcu_torture_boost() kthreads, which opens a window large enough for these
rcu_torture_boost() kthreads to wait (despite running at FIFO priority)
for ksoftirqds that are still running at SCHED_NORMAL priority.
Currently, in CONFIG_RCU_BOOST kernels, if the rcu_torture_init()
function's call to cpuhp_setup_state() fails, rcu_torture_cleanup()
gamely passes nonsense to cpuhp_remove_state(). This results in
strange and misleading splats. This commit therefore ensures that if
the rcu_torture_init() function's call to cpuhp_setup_state() fails,
rcu_torture_cleanup() avoids invoking cpuhp_remove_state().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running rcutorture as a module, any rcu_torture_init() issues will be
reflected in the error code from modprobe or insmod, as the case may be.
However, these error codes are not available when running rcutorture
built-in, for example, when using the kvm.sh script. This commit
therefore adds WARN_ON_ONCE() to allow distinguishing rcu_torture_init()
errors when running rcutorture built-in.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
radeon is MIT. This were incorrectly changed in
commit 4518740dfae2 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
and
commit 34602d9d9ac6 (".gitignore: add SPDX License Identifier")
and:
commit af50a7e88245 ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Fixes: 34602d9d9ac6 (".gitignore: add SPDX License Identifier") Fixes: af50a7e88245 ("treewide: Add SPDX license identifier - Makefile/Kconfig") Fixes: 4518740dfae2 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2053 Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: 92be5c71117b ("iwlwifi: split the drivers for agn and legacy devices 3945/4965") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to not add fancy protection for drv_priv we can move
htc_handle->drv_priv initialization at the end of the
ath9k_htc_probe_device() and add helper macro to make
all *_STAT_* macros NULL safe, since syzbot has reported related NULL
deref in that macros [1]
The hardware can support any image size WxH,
with arbitrary W (image width) and H (image height) dimensions.
Align upwards buffer size for both encoder and decoder.
and leave the picture resolution unchanged.
For decoder, the risk of memory out of bounds can be avoided.
For both encoder and decoder, the driver will lift the limitation of
resolution alignment.
For example, the decoder can support jpeg whose resolution is 227x149
the encoder can support nv12 1080P, won't change it to 1920x1072.
Fixes: d07d57ca19d16 ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder") Signed-off-by: Ming Qian <ming.qian@nxp.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To support dynamic resolution change,
driver should meet the following conditions:
1. the previous pictures are all decoded before source change event.
2. prevent decoding new resolution pictures with incorrect capture
buffer, until user handle source change event and setup capture.
3. report correct fmt and resolution during source change.
The decoder will save the precision that was detected from jpeg header
and use it later, when choosing the pixel format and also calculate
bytesperline according to precision.
The 12bit jpeg is not supported yet,
but driver shouldn't led to serious problem if user enqueue a 12 bit jpeg.
And the 12bit jpeg is supported by hardware, driver may support it later.
V4L2_PIX_FMT_NV12 requires num_planes equals to 1,
V4L2_PIX_FMT_NV12M requires num_planes equals to 2.
and mxc-jpeg supports 2 planes for nv12,
so we should use 4L2_PIX_FMT_NV12M instead of V4L2_PIX_FMT_NV12,
otherwise it will confuses gstreamer and prevent encoding and decoding.
Save some power by disabling/enabling the jpeg clocks with
every stream stop/start.
Do not use DL_FLAG_RPM_ACTIVE in mxc_jpeg_attach_pm_domains,
to ensure power domains are off after probe.
There is a hardware bug that it will load
the first 128 bytes of configuration data twice,
it will led to some configure error.
so shift the configuration data 128 bytes,
and make the first 128 bytes all zero,
then hardware will load the 128 zero twice,
and ignore them as garbage.
then the configuration data can be loaded correctly
the register CAST_NOMFRSIZE_LO should be equal to CAST_STATUS16
the register CAST_NOMFRSIZE_HI should be equal to CAST_STATUS17
the register CAST_OFBSIZE_LO should be equal to CAST_STATUS18
the register CAST_OFBSIZE_HI should be equal to CAST_STATUS19
We got the following warning when booting the kernel:
[ 3.243674] INFO: trying to register non-static key.
[ 3.243922] The code is fine but needs lockdep annotation, or maybe
[ 3.244230] you didn't initialize this object before use?
[ 3.245642] Call Trace:
[ 3.247836] lock_acquire+0xff/0x2d0
[ 3.248727] tw686x_audio_irq+0x1a5/0xcc0 [tw686x]
[ 3.249211] tw686x_irq+0x1f9/0x480 [tw686x]
The lock 'vc->qlock' will be initialized in tw686x_video_init(), but the
driver registers the irq before calling the tw686x_video_init(), and we
got the warning.
Fix this by registering the irq at the end of probe
Fixes: 4013ca76ea36 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is similar to 3b204db75b63 ("can: netlink: allow
configuring of fixed bit rates without need for do_set_bittiming
callback") but for data bit rates instead of bit rates.
Usually CAN devices support configurable data bit rates. The limits
are defined by struct can_priv::data_bittiming_const. Another way is
to implement the struct can_priv::do_set_data_bittiming callback.
If the bit rate is configured via netlink, the can_changelink()
function checks that either can_priv::data_bittiming_const or struct
can_priv::do_set_data_bittiming is implemented.
In commit 405abb0e0c7b ("can: dev: add CAN interface API for fixed
bitrates") an API for configuring bit rates on CAN interfaces that
only support fixed bit rates was added. The supported bit rates are
defined by struct can_priv::bitrate_const.
However the above mentioned commit forgot to add the struct
can_priv::data_bitrate_const to the check in can_changelink().
In order to avoid to implement a no-op can_priv::do_set_data_bittiming
callback on devices with fixed data bit rates, extend the check in
can_changelink() accordingly.
Link: https://lore.kernel.org/all/20220613143633.4151884-1-mkl@pengutronix.de Fixes: 405abb0e0c7b ("can: dev: add CAN interface API for fixed bitrates") Acked-by: Max Staudt <max@enpas.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Usually CAN devices support configurable bit rates. The limits are
defined by struct can_priv::bittiming_const. Another way is to
implement the struct can_priv::do_set_bittiming callback.
If the bit rate is configured via netlink, the can_changelink()
function checks that either can_priv::bittiming_const or struct
can_priv::do_set_bittiming is implemented.
In commit 405abb0e0c7b ("can: dev: add CAN interface API for fixed
bitrates") an API for configuring bit rates on CAN interfaces that
only support fixed bit rates was added. The supported bit rates are
defined by struct can_priv::bitrate_const.
However the above mentioned commit forgot to add the struct
can_priv::bitrate_const to the check in can_changelink().
In order to avoid to implement a no-op can_priv::do_set_bittiming
callback on devices with fixed bit rates, extend the check in
can_changelink() accordingly.
Link: https://lore.kernel.org/all/20220611144248.3924903-1-mkl@pengutronix.de Fixes: 405abb0e0c7b ("can: dev: add CAN interface API for fixed bitrates") Reported-by: Max Staudt <max@enpas.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sk->sk_forward_alloc is 150000, and we need to schedule 150001 bytes,
we want to allocate 1 byte more (rounded up to one page),
instead of 150001 :/
Commit 6b4be4d3a70b ("drm: adv7511: Add support for
i2c_new_secondary_device") allows a device tree node to override
the default addresses of the secondary i2c devices. This is useful
for solving address conflicts on the i2c bus.
In adv7511_init_cec_regmap() the new i2c address of cec device is
read from device tree and immediately accessed, well before it is
written in the proper register to override the default address.
This can cause an i2c error during probe and a consequent probe
failure.
Once the new i2c address is read from the device tree, override
the default address before any attempt to access the cec.
Tested with adv7533 and stm32mp157f.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com> Fixes: 6b4be4d3a70b ("drm: adv7511: Add support for i2c_new_secondary_device") Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220607213144.427177-1-antonio.borneo@foss.st.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since drm_prime_pages_to_sg() function return error pointers.
The drm_gem_shmem_get_sg_table() function returns error pointers too.
Using IS_ERR() to check the return value to fix this.
Change all GEM SHMEM object functions that receive a GEM object
of type struct drm_gem_object to expect an object of type
struct drm_gem_shmem_object instead.
This change reduces the number of upcasts from struct drm_gem_object
by moving them into callers. The C compiler can now verify that the
GEM SHMEM functions are called with the correct type.
For consistency, the patch also renames drm_gem_shmem_free_object to
drm_gem_shmem_free. It further updates documentation for a number of
functions.
v3:
* fix docs for drm_gem_shmem_object_free()
v2:
* mention _object_ callbacks in docs (Daniel)
Wrap GEM SHMEM functions for struct drm_gem_object_funcs and update
all callers. This will allow for an update of the public interfaces
of the GEM SHMEM helper library.
v2:
* fix docs for drm_gem_shmem_object_print_info()
'cache_ent' could be set NULL inside virtio_gpu_cmd_get_capset()
and it will lead to a NULL dereference by a lately use of it
(i.e., ptr = cache_ent->caps_cache). Fix it with a NULL check.
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 58fafb9526b2 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During device remove care needs to be taken that no work is pending
before it removes the underlying DRM bridge etc, but this can be done on
the specific work rather than waiting for the flush of the system-wide
workqueue.
Fixes: 50555d0f70e5 ("drm/bridge/lontium-lt9611uxc: move HPD notification out of IRQ handler") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220601233818.1877963-1-bjorn.andersson@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 14d402143ac8 ("drm/meson: split out encoder from meson_dw_hdmi") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220601033927.47814-3-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This implements the necessary change to no more use the embedded
connector in dw-hdmi and use the dedicated bridge connector driver
by passing DRM_BRIDGE_ATTACH_NO_CONNECTOR to the bridge attach call.
The necessary connector properties are added to handle the same
functionalities as the embedded dw-hdmi connector, i.e. the HDR
metadata, the CEC notifier & other flags.
The dw-hdmi output_port is set to 1 in order to look for a connector
next bridge in order to get DRM_BRIDGE_ATTACH_NO_CONNECTOR working.
In the dsi_enable function, mtk_dsi_rxtx_control is to
pull up the MIPI signal operation. Before dsi_disable,
MIPI should also be pulled down by writing a register
instead of disabling dsi.
If disable dsi without pulling the mipi signal low, the value of
the register will still maintain the setting of the mipi signal being
pulled high.
After resume, even if the mipi signal is not pulled high, it will still
be in the high state.
In order to match the changes of "Use the drm_panel_bridge API",
the poweron/poweroff of dsi is extracted from enable/disable and
defined as new funcs (atomic_pre_enable/atomic_post_disable).
Since dsi_poweron is moved from dsi_enable to pre_enable function, in
order to avoid poweron failure, the operation of dsi register fails to
cause bus hang. Therefore, the protection mechanism is added to the
dsi_enable function.
Fixes: 391bb3ed9f63 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API") Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-3-git-send-email-xinlei.lee@mediatek.com/ Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The last case label can write two buffers 'mc_reg_address[j]' and
'mc_data[j]' with 'j' offset equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE
since there are no checks for this value in both case labels after the
last 'j++'.
Instead of changing '>' to '>=' there, add the bounds check at the start
of the second 'case' (the first one already has it).
Also, remove redundant last checks for 'j' index bigger than array size.
The expression is always false. Moreover, before or after the patch
'table->last' can be equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE and it
seems it can be a valid value.
Detected using the static analysis tool - Svace. Fixes: d6db65a0436f ("drm/radeon/kms: add dpm support for cayman (v5)") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently a couple of debug_mask entries are mapped to the same value,
this could enable unintended driver logging. If enabling DP_TX logs was
the intention, then this could also enable PCI logs flooding the dmesg
buffer or vice versa. Fix this by correctly assigning the debug masks.
In __spi_validate, there's a validation that no partial transfers
are accepted (xfer->len % w_size must be zero). When
max_chunk is not a multiple of bpw (e.g. max_chunk = 65535,
bpw = 16), the transfer will be rejected.
This patch aligns max_chunk to 2 bytes (the maximum value of bpw is 16),
so that no partial transfer will occur.
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.
If the copy_from_user() fails or the user gives invalid date then the
correct thing to do is to return a negative error code. (Currently it
returns success).
I made a copy additional related cleanups:
1) There is no need to check "buffer" for NULL. That's handled by
copy_from_user().
2) The "h2c_len" variable cannot be negative because it is unsigned
and because sscanf() does not return negative error codes.
Fixes: 60701bcdfbec ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/YoOLnDkHgVltyXK7@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
If CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y && CONFIG_DRM_DISPLAY_HELPER=m,
bulding fails:
drivers/gpu/drm/panel/panel-samsung-atna33xc20.o: In function `atana33xc20_probe':
panel-samsung-atna33xc20.c:(.text+0x744): undefined reference to
`drm_panel_dp_aux_backlight'
make: *** [vmlinux] Error 1
Let CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20 select DRM_DISPLAY_DP_HELPER and
CONFIG_DRM_DISPLAY_HELPER to fix this error.
Fixes: 76db0fa2d68f ("drm/panel: atna33xc20: Introduce the Samsung ATNA33XC20 panel") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Gao Chao <gaochao49@huawei.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220524024551.539-1-gaochao49@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that the st7735r.ko module won't autoload if
a DT has a node with a compatible "okaya,rh128128t" string.
In that case, kmod expects a "MODALIAS=of:N*T*Cokaya,rh128128t" uevent but
instead will get a "MODALIAS=spi:rh128128t", which is not present in the
list of aliases:
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge rising - but instead rely on Devicetree to configure it.
All Qualcomm DTSI with WCN3990 define the interrupt type as level high,
so the mismatch between DTSI and driver causes rebind issues:
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/unbind
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/bind
[ 44.763114] irq: type mismatch, failed to map hwirq-446 for interrupt-controller@17a00000!
[ 44.763130] ath10k_snoc 18800000.wifi: error -ENXIO: IRQ index 0 not found
[ 44.763140] ath10k_snoc 18800000.wifi: failed to initialize resource: -6
The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. In order to support the rest of the modes without
making the tc_probe() overly long, split the bridge endpoint parsing
into dedicated function, where the necessary logic to detect the bridge
mode based on which endpoints are connected, can be implemented.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-7-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
While working on the DP AUX bus code I found a few small things that
should be fixed. Namely the non-devm version of
of_dp_aux_populate_ep_devices() was missing an export. There was also
an extra blank line in a kerneldoc and a kerneldoc that incorrectly
documented a return value. Fix these.
val = (u64)NSEC_PER_SEC * LPC18XX_PWM_TIMER_MAX;
do_div(val, lpc18xx_pwm->clk_rate);
lpc18xx_pwm->max_period_ns = val;
is bogus because with NSEC_PER_SEC = 1000000000,
LPC18XX_PWM_TIMER_MAX = 0xffffffff and clk_rate < NSEC_PER_SEC this
overflows the (on lpc18xx (i.e. ARM32) 32 bit wide) unsigned int
.max_period_ns. This results (dependant of the actual clk rate) in an
arbitrary limitation of the maximal period. E.g. for clkrate = 333333333 (Hz) we get max_period_ns = 9 instead of 12884901897.
So make .max_period_ns an u64 and pass period and duty as u64 to not
discard relevant digits. And also make use of mul_u64_u64_div_u64()
which prevents all overflows assuming clk_rate < NSEC_PER_SEC.
So this reduces stack usage, has an improved runtime behavior because of
better pipeline usage, doesn't branch to an external function and the
generated code is a bit smaller occupying less memory.
The codesize of lpc18xx_pwm_probe() is reduced by 32 bytes.
Each devm allocations has an overhead of 24 bytes to store the related
struct devres_node additionally to the fragmentation of the allocator.
So allocating 16 struct lpc18xx_pwm_data (which only hold a single int)
adds quite some overhead. Instead put the per-channel data into the
driver data struct and allocate it in one go.
.apply() assumes the clk to be for a given PWM iff the PWM is enabled.
So make sure this is the case when .probe() completes. And in .remove()
disable the according number of times.
This fixes a clk enable/disable imbalance, if some PWMs are already running
at probe time.
Fixes: 1afcd3819818 (pwm: sifive: Add a driver for SiFive SoC PWM) Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of explicitly using PWM_SIFIVE_PWMCMP0 + pwm->hwpwm *
PWM_SIFIVE_SIZE_PWMCMP for each access to one of the PWMCMP registers,
introduce a macro that takes the hwpwm id as parameter.
For the register definition using a plain 4 instead of the cpp constant
PWM_SIFIVE_SIZE_PWMCMP is easier to read, so define the offset macro
without the constant. The latter can then be dropped as there are no
users left.
Include sys/time.h and pthread.h in tmon.h, so that types
"pthread_mutex_t" and "struct timeval tv" are known when tmon.h
references them.
Without these headers, compiling tmon against musl-libc will fail with
these errors:
In file included from sysfs.c:31:0:
tmon.h:47:8: error: unknown type name 'pthread_mutex_t'
extern pthread_mutex_t input_lock;
^~~~~~~~~~~~~~~
make[3]: *** [<builtin>: sysfs.o] Error 1
make[3]: *** Waiting for unfinished jobs....
In file included from tui.c:31:0:
tmon.h:54:17: error: field 'tv' has incomplete type
struct timeval tv;
^~
make[3]: *** [<builtin>: tui.o] Error 1
make[2]: *** [Makefile:83: tmon] Error 2
Signed-off-by: Markus Mayer <mmayer@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Acked-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Tested-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Fixes: e8658e3e2d63 ("tools/thermal: Introduce tmon, a tool for thermal subsystem") Link: https://lore.kernel.org/r/20220718031040.44714-1-f.fainelli@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang has -Wconstant-conversion by default, and the constant 0xAAAAAAAAA
(9 As) being converted to an int, which is generally 32 bits, results
in the compile warning:
clang -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/ -lpthread seccomp_bpf.c -lcap -o seccomp_bpf
seccomp_bpf.c:812:67: warning: implicit conversion from 'long' to 'int' changes value from 45812984490 to -1431655766 [-Wconstant-conversion]
int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
~~~~ ^~~~~~~~~~~
1 warning generated.
-1431655766 is the expected truncation, 0xAAAAAAAA (8 As), so use
this directly in the code to avoid the warning.
On Fri, Jun 17, 2022 at 02:08:52PM +0300, Stephane Eranian wrote:
> Some changes to the way invalid MSR accesses are reported by the
> kernel is causing some problems with messages printed on the
> console.
>
> We have seen several cases of ex_handler_msr() printing invalid MSR
> accesses once but the callstack multiple times causing confusion on
> the console.
> The problem here is that another earlier commit (5.13):
>
> d771386e4102 ("once: implement DO_ONCE_LITE for non-fast-path "do once" functionality")
>
> Modifies all the pr_*_once() calls to always return true claiming
> that no caller is ever checking the return value of the functions.
>
> This is why we are seeing the callstack printed without the
> associated printk() msg.
Extract the ONCE_IF(cond) part into __ONCE_LTE_IF() and use that to
implement DO_ONCE_LITE_IF() and fix the extable code.
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes: 3dc8fc879e57 ("sched: Migrate sched to use new tick dependency mask model") Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <vschneid@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The arm_spe_pmu driver will enable SYS_PMSCR_EL1.CX in order to add CONTEXT
packets into the traces, if the owner of the perf event runs with required
capabilities i.e CAP_PERFMON or CAP_SYS_ADMIN via perfmon_capable() helper.
The value of this bit is computed in the arm_spe_event_to_pmscr() function
but the check for capabilities happens in the pmu event init callback i.e
arm_spe_pmu_event_init(). This suggests that the value of the CX bit should
remain consistent for the duration of the perf session.
However, the function arm_spe_event_to_pmscr() may be called later during
the event start callback i.e arm_spe_pmu_start() when the "current" process
is not the owner of the perf session, hence the CX bit setting is currently
not consistent.
One way to fix this, is by caching the required value of the CX bit during
the initialization of the PMU event, so that it remains consistent for the
duration of the session. It uses currently unused 'event->hw.flags' element
to cache perfmon_capable() value, which can be referred during event start
callback to compute SYS_PMSCR_EL1.CX. This ensures consistent availability
of context packets in the trace as per event owner capabilities.
Drop BIT(SYS_PMSCR_EL1_CX_SHIFT) check in arm_spe_pmu_event_init(), because
now CX bit cannot be set in arm_spe_event_to_pmscr() with perfmon_capable()
disabled.
Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Fixes: 5a75be7e6ec9 ("drivers/perf: Add support for ARMv8.2 Statistical Profiling Extension") Reported-by: German Gomez <german.gomez@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220714061302.2715102-1-anshuman.khandual@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using a NOMAP domain, __irq_resolve_mapping() doesn't store
the Linux IRQ number at the address optionally provided by the caller.
While this isn't a huge deal (the returned value is guaranteed
to the hwirq that was passed as a parameter), let's honour the letter
of the API by writing the expected value.
Currently the DT for QCS404 SoC has setup for 2 USB2 PHYs with one each
assigned to USB3 controller and USB2 controller. This assignment is
incorrect which only works by luck: as when each USB HCI comes up it
configures the *other* controllers PHY which is enough to make them
happy. If, for any reason, we were to disable one of the controllers then
both would stop working.
This was a difficult inconsistency to be caught which was found while
trying to enable USB support in u-boot. So with all the required drivers
ported to u-boot, I couldn't get the same USB storage device enumerated
in u-boot which was being enumerated fine by the kernel.
The root cause of the problem came out to be that I wasn't enabling USB2
PHY: "usb2_phy_prim" in u-boot. Then I realised that via simply disabling
the same USB2 PHY currently assigned to USB2 host controller in the
kernel disabled enumeration for USB3 host controller as well.
So fix this inconsistency by correctly assigning USB2 PHYs.
Fixes: af153ec753ba ("arm64: dts: qcom: qcs404: Add USB devices and PHYs") Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220711083038.1518529-1-sumit.garg@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
QCOM_RPMPD requires PM_GENERIC_DOMAINS/_OF, which in turns requires
CONFIG_PM. I forgot about the latter in my earlier patch (it's still
in -next as of the time of committing, hence no Fixes: tag). Fix it.
We should call the of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: ece05fa76e95 ("regulator: of: Add support for parsing regulator_state for suspend state") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220715111027.391032-1-windhl@126.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change dm-writecache, so that it counts the number of blocks discarded
instead of the number of discard bios. Make it consistent with the
read and write statistics counters that were changed to count the
number of blocks instead of bios.
Change dm-writecache, so that it counts the number of blocks written
instead of the number of write bios. Bios can be split and requeued
using the dm_accept_partial_bio function, so counting bios caused
inaccurate results.
Change dm-writecache, so that it counts the number of blocks read
instead of the number of read bios. Bios can be split and requeued
using the dm_accept_partial_bio function, so counting bios caused
inaccurate results.
Both genpd_debug_add() and genpd_debug_remove() may be called
indirectly by other drivers while genpd_debugfs_dir is not yet
set. For example, drivers can call pm_genpd_init() in probe or
pm_genpd_init() in probe fail/cleanup path:
At this time, genpd_debug_init() may not yet be called.
genpd_debug_add() checks that if genpd_debugfs_dir is NULL, it
will return directly. Make sure this is also checked
in pm_genpd_remove(), otherwise components under debugfs root
which has the same name as other components under pm_genpd may
be accidentally removed, since NULL represents debugfs root.
Fixes: 79215baf0ddd ("PM: domains: create debugfs nodes when adding power domains") Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trace the remapped operation and its flags instead of only the data
direction of remapped operations. This issue was detected by analyzing
the warnings reported by sparse related to the new blk_opf_t type.
Reviewed-by: Jun'ichi Nomura <junichi.nomura@nec.com> Cc: Mike Snitzer <snitzer@kernel.org> Cc: Mike Christie <michael.christie@oracle.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Chaitanya Kulkarni <kch@nvidia.com> Fixes: 9dbf0eab28ec ("blktrace: use op accessors") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20220714180729.1065367-11-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org Fixes: 8e55853efe1f ("hwmon: Driver for disk and solid state drives with temperature sensors") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After calling spi_unregister_master(), the refcount of master will
be decrease to 0, and it will be freed in spi_controller_release(),
the device data also will be freed, so it will lead a UAF when using
'tspi'. To fix this, get the master before unregister and put it when
finish using it.
Fixes: a86d2af2b098 ("spi: tegra20-slink: Don't use resource-managed spi_register helper") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220713094024.1508869-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit c5f5dc71e6eb ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes: c5f5dc71e6eb ("spi: simplify devm_spi_register_controller") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
blk_mq_debugfs_register_hctx() can be called by blk_mq_update_nr_hw_queues
when gendisk isn't added yet, such as nvme tcp.
Fixes the warning of 'debugfs: Directory 'hctx0' with parent '/' already present!'
which can be observed reliably when running blktests nvme/005.
Fixes: 08a5d58dd943 ("blk-mq: no need to check return value of debugfs_create functions") Reported-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220711090808.259682-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Tegra SYSRAM contains regions access to which is restricted to
certain hardware blocks on the system, and speculative accesses to
those will cause issues.
Patch 'misc: sram: Only map reserved areas in Tegra SYSRAM' attempted
to resolve this by only mapping the regions specified in the device
tree on the assumption that there are no such restricted areas within
the 64K-aligned area of memory that contains the memory we wish to map.
Turns out this assumption is wrong, as there are such areas above the
4K pages described in the device trees. As such, we need to use the
bigger hammer that is no-memory-wc, which causes the memory to be
mapped as Device memory to which speculative accesses are disallowed.
As such, the previous patch in the series,
'firmware: tegra: bpmp: do only aligned access to IPC memory area',
is required with this patch to make the BPMP driver only issue aligned
memory accesses as those are also required with Device memory.
Fixes: efeafa4ddfc2 ("misc: sram: Only map reserved areas in Tegra SYSRAM") Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com> Reviewed-by: Yousaf Kaukab <ykaukab@suse.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The json-schema bindings for SRAM expect the nodes to be called "sram"
rather than "sysram" or "shmem". Furthermore, place the brackets around
the SYSRAM references such that a two-element array is created rather
than a two-element array nested in a single-element array. This is not
relevant for device tree itself, but allows the nodes to be properly
validated against json-schema bindings.
The bananapi R64 (BPI-R64) experiences wrong WPS button signals.
In OpenWrt pushing the WPS button while powering on the device will set
it to recovery mode. Currently, this also happens without any user
interaction. In particular, the wrong signals appear while booting the
device or restarting it, e.g. after doing a system upgrade. If the
device is in recovery mode the user needs to manually power cycle or
restart it.
The official BPI-R64 sources set the WPS button to GPIO_ACTIVE_LOW in
the device tree. This setting seems to suppress the unwanted WPS button
press signals. So this commit changes the button from GPIO_ACTIVE_HIGH to
GPIO_ACTIVE_LOW.
The official BPI-R64 sources can be found on
https://github.com/BPI-SINOVOIP/BPI-R64-openwrt
projects / kernel.git / log