Use ETZPC driver to configure secure aware interfaces to assign
them to non-secure world. Sp_min also configures BootROM resources
and SYSRAM to assign both to secure world only.
Define stm32mp15 SoC identifiers for the platform specific DECPROT
instances.
ETZPC stands for Extended TrustZone Protection Controller. It is a
resource conditional access device. It is mainly based on Arm TZPC.
ST ETZPC exposes memory mapped DECPROT cells to set access permissions
to SoC peripheral interfaces as I2C, SPI, DDR controllers, and some
of the SoC internal memories.
ST ETZPC exposes memory mapped TZMA cells to set access permissions
to some SoC internal memories.
Marcin Wojtas [Tue, 12 May 2020 16:19:33 +0000 (18:19 +0200)]
marvell: drivers: mochi: specify stream ID for SD/MMC
This patch enables the stream ID for the SD/MMC
controllers via dedicated unit register. Thanks to this
change it is possible to configure properly the
IOMMU in OS and use the SD/MMC interface in a guest
Virtual Machine.
Change-Id: I99cbd2c9882eb558ba01405d3d8a3e969f06e082 Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Marcin Wojtas [Tue, 2 Jun 2020 13:12:06 +0000 (15:12 +0200)]
marvell: a8k: enable BL31 cache by default
BL31_CACHE_DISABLE flag was introduced as a work-around
for the older SoC revisions. Since it is not relevant in the
newest versions, toggle it to be disabled by default.
One can still specify it by adding 'BL31_CACHE_DISABLE=1'
string to the build command.
Change-Id: I11b52dade3ff7f8ee643b8078c6e447c45946570 Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Jimmy Brisson [Thu, 16 Apr 2020 15:48:02 +0000 (10:48 -0500)]
Enable ARMv8.6-ECV Self-Synch when booting to EL2
Enhanced Counter Virtualization, ECV, is an architecture extension introduced
in ARMv8.6. This extension allows the hypervisor, at EL2, to setup
self-synchronizing views of the timers for it's EL1 Guests. This patch pokes the
control register to enable this extension when booting a hypervisor at EL2.
Change-Id: I4e929ecdf400cea17eff1de5cf8704aa7e40973d Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Jimmy Brisson [Thu, 16 Apr 2020 15:47:56 +0000 (10:47 -0500)]
Enable ARMv8.6-FGT when booting to EL2
The Fine Grained Traps (FGT) architecture extension was added to aarch64 in
ARMv8.6. This extension primarily allows hypervisors, at EL2, to trap specific
instructions in a more fine grained manner, with an enable bit for each
instruction. This patch adds support for this extension by enabling the
extension when booting an hypervisor at EL2.
Change-Id: Idb9013ed118b6a1b7b76287237096de992ca4da3 Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
drivers: stm32_reset adapt interface to timeout argument
Changes stm32mp1 reset driver to API to add a timeout argument
to stm32mp_reset_assert() and stm32mp_reset_deassert() and
a return value.
With a supplied timeout, the functions wait the target reset state
is reached before returning. With a timeout of zero, the functions
simply load target reset state in SoC interface and return without
waiting.
Helper functions stm32mp_reset_set() and stm32mp_reset_release()
use a zero timeout and return without a return code.
This change updates few stm32 drivers and plat/stm32mp1 blé_plat_setup.c
accordingly without any functional change.
functional change.
Alexei Fedorov [Sat, 30 May 2020 16:33:26 +0000 (17:33 +0100)]
TF-A: Fix BL31 linker script error
The patch fixes BL31 linker script error
"Init code ends past the end of the stacks"
for platforms with number of CPUs less than 4,
which is caused by __STACKS_END__ address being
lower than __INIT_CODE_END__.
The modified BL31 linker script detects such cases
and increases the total amount of stack memory,
setting __STACKS_END__ = __INIT_CODE_END__, and
CPUs' stacks are calculated by BL31 'plat_get_my_stack'
function accordingly. For platforms with more than 4 CPUs
and __INIT_CODE_END__ < __STACKS_END__ stack memory does not
increase and allocated CPUs' stacks match the existing
implementation.
The patch removes exclusion of PSCI initialization
functions from the reclaimed .init section in
'arm_reclaim_init.ld.S' script, which increases the
size of reclaimed memory region.
As per the trustedfirmware.org Project Maintenance Process [1], the
current maintainers of the TF-A project have nominated some contributors
to become maintainers themselves. List them in the maintainers.rst file
to make this official.
Usama Arif [Fri, 17 Apr 2020 15:13:39 +0000 (16:13 +0100)]
plat/arm: Introduce TC0 platform
This patch adds support for Total Compute (TC0) platform. It is an
initial port and additional features are expected to be added later.
TC0 has a SCP which brings the primary Cortex-A out of reset
which starts executing BL1. TF-A optionally authenticates the SCP
ram-fw available in FIP and makes it available for SCP to copy.
Some of the major features included and tested in this platform
port include TBBR, PSCI, MHUv2 and DVFS.
Change-Id: I1675e9d200ca7687c215009eef483d9b3ee764ef Signed-off-by: Usama Arif <usama.arif@arm.com>
Fixed build error for dualroot chain of trust.
Build error were thrown as below while compiling the code for
dualroot chain of trust:
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.bss.auth_img_flags+0x0): multiple definition of `auth_img_flags';
./build/fvp/debug/bl1/cot.o:(.bss.auth_img_flags+0x0): first defined here
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.rodata.cot_desc_size+0x0): multiple definition of `cot_desc_size';
./build/fvp/debug/bl1/cot.o:(.rodata.cot_desc_size+0x0): first defined here
aarch64-none-elf-ld.bfd: ./build/fvp/debug/bl1/tbbr_cot_bl1.o:
(.rodata.cot_desc_ptr+0x0): multiple definition of `cot_desc_ptr';
./build/fvp/debug/bl1/cot.o:(.rodata.cot_desc_ptr+0x0): first defined here
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I1a426c4e7f5f8013d71dafc176c7467c1b329757
Alexei Fedorov [Tue, 26 May 2020 12:16:41 +0000 (13:16 +0100)]
TF-A: Fix wrong register read for MPAM extension
This patch fixes wrong ID_AA64DFR0_EL1 register read instead of
ID_AA64PFR0_EL1 to detect support for MPAM extension.
It also implements get_mpam_version() function which returns
MPAM version as:
0x00: None Armv8.0 or later;
0x01: v0.1 Armv8.4 or later;
0x10: v1.0 Armv8.2 or later;
0x11: v1.1 Armv8.4 or later;
- Fix possible run-time ELs value and xlat-granule size.
- Remove mandatory field for stream-ids.
- Define interrupts attributes to <u32>.
- Remove mem-manage field.
- Add description for memory/device region attributes.
J-Alves [Thu, 7 May 2020 17:42:25 +0000 (18:42 +0100)]
SPCI is now called PSA FF-A
SPCI is renamed as PSA FF-A which stands for Platform Security
Architecture Firmware Framework for A class processors.
This patch replaces the occurrence of SPCI with PSA FF-A(in documents)
or simply FFA(in code).
plat/fvp: Support for extracting UART serial node info from DT
This patch introduces the populate function which leverages
a new driver to extract base address and clk frequency properties
of the uart serial node from HW_CONFIG device tree.
This patch also introduces fdt helper API fdtw_translate_address()
which helps in performing address translation.
This patch enables SDEI support for all Tegra platforms, with
the following configuration settings.
* SGI 8 as the source IRQ
* Special Private Event 0
* Three private, dynamic events
* Three shared, dynamic events
* Twelve general purpose explicit events
Verified using TFTF SDEI test suite.
******************************* Summary *******************************
Test suite 'SDEI' Passed
=================================
Tests Skipped : 0
Tests Passed : 5
Tests Failed : 0
Tests Crashed : 0
Total tests : 5
=================================
This patch enables the v8.6 extension to add a delay before WFE traps
are taken. A weak hook plat_arm_set_twedel_scr_el3 has been added in
plat/common/aarch64/plat_common.c that disables this feature by default
but platform-specific code can override it when needed.
The only hook provided sets the TWED fields in SCR_EL3, there are similar
fields in HCR_EL2, SCTLR_EL2, and SCTLR_EL1 to control WFE trap delays in
lower ELs but these should be configured by code running at EL2 and/or EL1
depending on the platform configuration and is outside the scope of TF-A.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I0a9bb814205efeab693a3d0a0623e62144abba2d
Alexei Fedorov [Wed, 13 May 2020 20:13:57 +0000 (21:13 +0100)]
FVP: Add support for passing platform's topology to DTS
This patch adds support for passing FVP platform's topology
configuration to DTS files for compilation, which allows to
build DTBs with correct number of clusters and CPUs.
This removes non-existing clusters/CPUs from the compiled
device tree blob and fixes reported Linux errors when trying
to power on absent CPUs/PEs.
If DTS file is passed using FVP_HW_CONFIG_DTS build option from
the platform's makefile, FVP_CLUSTER_COUNT, FVP_MAX_CPUS_PER_CLUSTER
and FVP_MAX_PE_PER_CPU parameters are used, otherwise CI script will
use the default values from the corresponding DTS file.
CoT used for BL1 and BL2 are moved to tbbr_cot_bl1.c
and tbbr_cot_bl2.c respectively.
Common CoT used across BL1 and BL2 are moved to
tbbr_cot_common.c.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2252ac8a6960b3431bcaafdb3ea4fb2d01b79cf5
Balint Dobszay [Wed, 18 Dec 2019 14:28:00 +0000 (15:28 +0100)]
plat/arm/fvp: Support performing SDEI platform setup in runtime
This patch introduces dynamic configuration for SDEI setup and is supported
when the new build flag SDEI_IN_FCONF is enabled. Instead of using C arrays
and processing the configuration at compile time, the config is moved to
dts files. It will be retrieved at runtime during SDEI init, using the fconf
layer.
During context switching from higher EL (EL2 or higher)
to lower EL can cause incorrect translation in TLB due to
speculative execution of AT instruction using out-of-context
translation regime.
Workaround is implemented as below during EL's (EL1 or EL2)
"context_restore" operation:
1. Disable page table walk using SCTLR.M and TCR.EPD0 & EPD1
bits for EL1 or EL2 (stage1 and stage2 disabled)
2. Save all system registers except TCR and SCTLR (for EL1 and EL2)
3. Do memory barrier operation (isb) to ensure all
system register writes are done.
4. Restore TCR and SCTLR registers (for EL1 and EL2)
Errata details are available for various CPUs as below:
Cortex-A76: 1165522
Cortex-A72: 1319367
Cortex-A57: 1319537
Cortex-A55: 1530923
Cortex-A53: 1530924
More details can be found in mail-chain:
https://lists.trustedfirmware.org/pipermail/tf-a/2020-April/000445.html
Currently, Workaround is implemented as build option which is default
disabled.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: If8545e61f782cb0c2dda7ffbaf50681c825bd2f0
The maintainers.rst file provides the list of all TF-A modules and their
code owners. As there are quite a lot of modules (and more to come) in
TF-A, it is sometimes hard to find the information.
Introduce categories (core code, drivers/libraries/framework, ...) and
classify each module in the right one.
Note that the core code category is pretty much empty right now but the
plan would be to expand it with further modules (e.g. PSCI, SDEI, TBBR,
...) in a future patch.
Olivier Deprez [Fri, 7 Feb 2020 14:44:43 +0000 (15:44 +0100)]
SPMD: extract SPMC DTB header size from SPMD
Currently BL2 passes TOS_FW_CONFIG address and size through registers to
BL31. This corresponds to SPMC manifest load address and size. The SPMC
manifest is mapped in BL31 by dynamic mapping. This patch removes BL2
changes from generic code (which were enclosed by SPD=spmd) and retrieves
SPMC manifest size directly from within SPMD. The SPMC manifest load
address is still passed through a register by generic code.
As a follow-up to bdd2596d4, and related to SPM Dispatcher
EL3 component and SPM Core S-EL2/S-EL1 component: update
with cosmetic and coding rules changes. In addition:
-Add Armv8.4-SecEL2 arch detection helper.
-Add an SPMC context (on current core) get helper.
-Return more meaningful error return codes.
-Remove complexity in few spmd_smc_handler switch-cases.
-Remove unused defines and structures from spmd_private.h
drivers: stm32mp1 clocks: fix debug trace on clock enable/disable
Adds missing terminal new line character '\n' to debug traces,
fix format as index is an unsigned value and use present tense rather
than past tense in the printed message.
drivers: stm32mp1 clocks: prevent crash on always on clocks
Oscillators and PLLs are not gated on stm32mp_clk_enable/disable()
calls. This change prevents functions to panic when called for such
always-on clocks. Gating these clocks is out of the scope of
this change.
drivers: stm32mp1 clocks: add RTC as a gateable clock
Adds RTC clock to the list of the supported clocks. This allows
stm32mp_clk_*() API functions to enable, disable and set and get
rate for the clock RTC clock.
drivers: stm32mp1 clocks: support shifted clock selector bit masks
The current implementation optimizes memory consumed by gateable
clock table by storing bit mask and bit shift with 1 byte each.
The issue is that register selector bit masks above the 7th LSBit
cannot be stored.
This change uses the shift info to shift the mask before it is used,
allowing clock selector register bit fields to be spread on the 32 bits
of the register as long as the mask fits in 8 contiguous bit at most.
This change is needed to add the RTC clock to the gateable clocks table.
drivers: stm32mp1 clocks: allow tree lookup for several system clocks
Oscillators, PLLs and some system clocks can be related straight to
a parent clock. Prior this change were only oscillators and few
clocks supported by this look up. This changes adds PLLs and other
system clocks. This enables for flexible use of clock tree exploration
when computing a clock frequency value.
plat/stm32mp1: fdt helpers for secure aware gpio bank
New helper functions to get GPIO banks configuration from the FDT.
stm32_get_gpio_bank_pinctrl_node() allows stm32mp platforms to
differentiate specific GPIO banks when these are defined with a specific
path in the FDT.
fdt_get_gpio_bank_pin_count() returns the number of pins in a GPIO bank
as it depends on the SoC variant.
plat/st: move GPIO bank helper function to platform source files
Relation between GPIO banks and their base address and offset address
if platform dependent. This change moves helper functions
stm32_get_gpio_bank_base() and stm32_get_gpio_bank_offset() from
plat/st/common to plat/st/stm32mp1/.
Merge changes from topic "fdt_wrappers_rework" into integration
* changes:
arm_fpga: Read UART address from DT
arm_fpga: Read GICD and GICR base addresses from DT
arm_fpga: Read generic timer counter frequency from DT
arm_fpga: Use Generic UART
Andre Przywara [Thu, 9 Apr 2020 09:25:43 +0000 (10:25 +0100)]
arm_fpga: Read UART address from DT
The arm_fpga port requires a DTB, to launch a BL33 payload.
To make this port more flexible, we can also use the information in the
DT to configure the console driver.
For a start, find the DT node pointed to by the stdout-path property, and
read the base address from there.
This assumes for now that the stdout-path points to a PL011 UART.
This allows to remove platform specific addresses from the image. We
keep the original base address for the crash console.
Change-Id: I46a990de2315f81cae4d7913ae99a07b0bec5cb1 Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 9 Apr 2020 10:27:21 +0000 (11:27 +0100)]
plat/stm32: Use generic fdt_get_stdout_node_offset()
Now that we have an implementation for getting the node offset of the
stdout-path property in the generic fdt_wrappers code, use that to
replace the current ST platform specific implementation.
Change-Id: I5dd05684e7ca3cb563b5f71c885e1066393e057e Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 26 Mar 2020 12:52:06 +0000 (12:52 +0000)]
fdt/wrappers: Introduce code to find UART DT node
The stdout-path property in the /chosen node of a DTB points to a device
node, which is used for boot console output.
On most (if not all) ARM based platforms this is the debug UART.
The ST platform code contains a function to parse this property and
chase down eventual aliases to learn the node offset of this UART node.
Introduce a slightly more generalised version of this ST platform function
in the generic fdt_wrappers code. This will be useful for other platforms
as well.
Change-Id: Ie6da47ace7833861b5e35fe8cba49835db3659a5 Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Fri, 24 Jan 2020 15:02:27 +0000 (15:02 +0000)]
arm_fpga: Read generic timer counter frequency from DT
The ARM Generic Timer DT binding describes an (optional) property to
declare the counter frequency. Its usage is normally discouraged, as the
value should be read from the CNTFRQ_EL0 system register.
However in our case we can use it to program this register in the first
place, which avoids us to hard code a counter frequency into the code.
We keep some default value in, if the DT lacks that property for
whatever reason.
Change-Id: I5b71176db413f904f21eb16f3302fbb799cb0305 Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 26 Mar 2020 12:11:34 +0000 (12:11 +0000)]
plat/stm32: Use generic fdt_get_reg_props_by_name()
The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.
Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.
Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Thu, 9 Apr 2020 09:10:09 +0000 (10:10 +0100)]
arm_fpga: Use Generic UART
The SCP firmware on the ARM FPGA initialises the UART already. This allows
us to treat the PL011 as an SBSA Generic UART, which does not require
any further setup.
This in particular removes the need for any baudrate and base clock related
settings to be hard coded into the BL31 image.
Change-Id: I16fc943526267356b97166a7068459e06ff77f0f Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 0e753437e75b ("Implement SMCCC_ARCH_SOC_ID SMC call") executes
and return the result of SMCCC_ARCH_SOC_ID(soc_id_type) to the
SMCCC_ARCH_FEATURES(SMCCC_ARCH_SOC_ID) itself. Moreover it expect to
pass soc_id_type for SMCCC_ARCH_FEATURES(SMCCC_ARCH_SOC_ID) which is
incorrect.
Fix the implementation by returning SMC_OK for
SMCCC_ARCH_FEATURES(SMCCC_ARCH_SOC_ID) always and move the current
implementation under "smccc_arch_id" function which gets called from
SMC handler on receiving "SMCCC_ARCH_SOC_ID" command.
projects / arm-tf.git / log