After PF reset and ethtool -t there was call trace in dmesg
sometimes leading to panic. When there was some time, around 5
seconds, between reset and test there were no errors.
Problem was that pf reset calls i40e_vsi_close in prep_for_reset
and ethtool -t calls i40e_vsi_close in diag_test. If there was not
enough time between those commands the second i40e_vsi_close starts
before previous i40e_vsi_close was done which leads to crash.
Add check to diag_test if pf is in reset and don't start offline
tests if it is true.
Add netif_info("testing failed") into unhappy path of i40e_diag_test()
Fixes: f6d7cf4d42bd ("i40e: Disable offline diagnostics if VFs are enabled") Fixes: 7cd7df842ad1 ("i40e: Fix ethtool offline diagnostic with netqueues") Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Procedure of configure tc flower filters erroneously allows to create
filters on TC0 where unfiltered packets are also directed by default.
Issue was caused by insufficient checks of hw_tc parameter specifying
the hardware traffic class to pass matching packets to.
Fix checking hw_tc parameter which blocks creation of filters on TC0.
Fixes: e17fea180694 ("i40e: Enable cloud filters via tc-flower") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
arch/x86/kernel/cpu/mshyperv.c is never compiled as modular.
(CONFIG_HYPERVISOR_GUEST is boolean)
Fixes: 05cb67b930fe ("clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20220606050238.4162200-1-masahiroy@kernel.org Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the initial attempt at trunking detection using the krb5i auth flavor
fails with -EACCES, -NFS4ERR_CLID_INUSE, or -NFS4ERR_WRONGSEC, then the
NFS client tries again using auth_sys, cloning the rpc_clnt in the
process. If this second attempt at trunking detection succeeds, then
the resulting nfs_client->cl_rpcclient winds up having cl_max_connect=0
and subsequent attempts to add additional transport connections to the
rpc_clnt will fail with a message similar to the following being logged:
[502044.312640] SUNRPC: reached max allowed number (0) did not add
transport to server: 192.168.122.3
Signed-off-by: Scott Mayhew <smayhew@redhat.com> Fixes: c4ad2b816624 ("SUNRPC enforce creation of no more than max_connect xprts") Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're about to send the first layoutget for an empty layout, we want
to make sure that we drain out the existing pending layoutget calls
first. The reason is that these layouts may have been already implicitly
returned to the server by a recall to which the client gave a
NFS4ERR_NOMATCHING_LAYOUT response.
The problem is that wait_var_event_killable() could in principle see the
plh_outstanding count go back to '1' when the first process to wake up
starts sending a new layoutget. If it fails to get a layout, then this
loop can continue ad infinitum...
Fixes: db646d42be51 ("NFSv4/pnfs: Fix layoutget behaviour after invalidation") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Building with -Warray-bounds results in the following warning plus others
related to the same problem:
CC [M] drivers/staging/r8188eu/os_dep/ioctl_linux.o
In function ‘wpa_set_encryption’,
inlined from ‘rtw_wx_set_enc_ext’ at drivers/staging/r8188eu/os_dep/ioctl_linux.c:1868:9:
drivers/staging/r8188eu/os_dep/ioctl_linux.c:412:41: warning: array subscript ‘struct ndis_802_11_wep[0]’ is partly outside array bounds of ‘void[25]’ [-Warray-bounds]
412 | pwep->KeyLength = wep_key_len;
| ~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
In file included from drivers/staging/r8188eu/os_dep/../include/osdep_service.h:19,
from drivers/staging/r8188eu/os_dep/ioctl_linux.c:4:
In function ‘kmalloc’,
inlined from ‘kzalloc’ at ./include/linux/slab.h:733:9,
inlined from ‘wpa_set_encryption’ at drivers/staging/r8188eu/os_dep/ioctl_linux.c:408:11,
inlined from ‘rtw_wx_set_enc_ext’ at drivers/staging/r8188eu/os_dep/ioctl_linux.c:1868:9:
./include/linux/slab.h:605:16: note: object of size [17, 25] allocated by ‘__kmalloc’
605 | return __kmalloc(size, flags);
| ^~~~~~~~~~~~~~~~~~~~~~
./include/linux/slab.h:600:24: note: object of size [17, 25] allocated by ‘kmem_cache_alloc_trace’
600 | return kmem_cache_alloc_trace(
| ^~~~~~~~~~~~~~~~~~~~~~~
601 | kmalloc_caches[kmalloc_type(flags)][index],
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
602 | flags, size);
| ~~~~~~~~~~~~
Although it is unlikely that anyone is still using WEP encryption, the
size of the allocation needs to be increased just in case.
Fixes commit 4ba62aac0c9a ("staging: r8188eu: introduce new os_dep dir for RTL8188eu driver")
Fixes: 4ba62aac0c9a ("staging: r8188eu: introduce new os_dep dir for RTL8188eu driver") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Phillip Potter <phil@philpotter.co.uk> Cc: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220531013103.2175-3-Larry.Finger@lwfinger.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In _rtw_init_xmit_priv, we use the res variable to store the error
return from the newly converted rtw_alloc_hwxmits function. Sadly, the
calling function interprets res using _SUCCESS and _FAIL still, meaning
we change the semantics of the variable, even in the success case.
This leads to the following on boot:
r8188eu 1-2:1.0: _rtw_init_xmit_priv failed
In the long term, we should reverse these semantics, but for now, this
fixes the driver. Also, inside rtw_alloc_hwxmits remove the if blocks,
as HWXMIT_ENTRY is always 4.
The Surface Go reports Chassis Type 9 (Laptop,) so the device needs to be
added to dmi_vgbs_allow_list to enable tablet mode when an attached Type
Cover is folded back.
Currently if the APB or Debounce clocks aren't yet ready to be requested
the DW GPIO driver will correctly handle that by deferring the probe
procedure, but the error is still printed to the system log. It needlessly
pollutes the log since there was no real error but a request to postpone
the clock request procedure since the clocks subsystem hasn't been fully
initialized yet. Let's fix that by using the dev_err_probe method to print
the APB/clock request error status. It will correctly handle the deferred
probe situation and print the error if it actually happens.
This commit changes the default Kconfig values of RANDOM_TRUST_CPU and
RANDOM_TRUST_BOOTLOADER to be Y by default. It does not change any
existing configs or change any kernel behavior. The reason for this is
several fold.
As background, I recently had an email thread with the kernel
maintainers of Fedora/RHEL, Debian, Ubuntu, Gentoo, Arch, NixOS, Alpine,
SUSE, and Void as recipients. I noted that some distros trust RDRAND,
some trust EFI, and some trust both, and I asked why or why not. There
wasn't really much of a "debate" but rather an interesting discussion of
what the historical reasons have been for this, and it came up that some
distros just missed the introduction of the bootloader Kconfig knob,
while another didn't want to enable it until there was a boot time
switch to turn it off for more concerned users (which has since been
added). The result of the rather uneventful discussion is that every
major Linux distro enables these two options by default.
While I didn't have really too strong of an opinion going into this
thread -- and I mostly wanted to learn what the distros' thinking was
one way or another -- ultimately I think their choice was a decent
enough one for a default option (which can be disabled at boot time).
I'll try to summarize the pros and cons:
Pros:
- The RNG machinery gets initialized super quickly, and there's no
messing around with subsequent blocking behavior.
- The bootloader mechanism is used by kexec in order for the prior
kernel to initialize the RNG of the next kernel, which increases
the entropy available to early boot daemons of the next kernel.
- Previous objections related to backdoors centered around
Dual_EC_DRBG-like kleptographic systems, in which observing some
amount of the output stream enables an adversary holding the right key
to determine the entire output stream.
This used to be a partially justified concern, because RDRAND output
was mixed into the output stream in varying ways, some of which may
have lacked pre-image resistance (e.g. XOR or an LFSR).
But this is no longer the case. Now, all usage of RDRAND and
bootloader seeds go through a cryptographic hash function. This means
that the CPU would have to compute a hash pre-image, which is not
considered to be feasible (otherwise the hash function would be
terribly broken).
- More generally, if the CPU is backdoored, the RNG is probably not the
realistic vector of choice for an attacker.
- These CPU or bootloader seeds are far from being the only source of
entropy. Rather, there is generally a pretty huge amount of entropy,
not all of which is credited, especially on CPUs that support
instructions like RDRAND. In other words, assuming RDRAND outputs all
zeros, an attacker would *still* have to accurately model every single
other entropy source also in use.
- The RNG now reseeds itself quite rapidly during boot, starting at 2
seconds, then 4, then 8, then 16, and so forth, so that other sources
of entropy get used without much delay.
- Paranoid users can set random.trust_{cpu,bootloader}=no in the kernel
command line, and paranoid system builders can set the Kconfig options
to N, so there's no reduction or restriction of optionality.
- It's a practical default.
- All the distros have it set this way. Microsoft and Apple trust it
too. Bandwagon.
Cons:
- RDRAND *could* still be backdoored with something like a fixed key or
limited space serial number seed or another indexable scheme like
that. (However, it's hard to imagine threat models where the CPU is
backdoored like this, yet people are still okay making *any*
computations with it or connecting it to networks, etc.)
- RDRAND *could* be defective, rather than backdoored, and produce
garbage that is in one way or another insufficient for crypto.
- Suggesting a *reduction* in paranoia, as this commit effectively does,
may cause some to question my personal integrity as a "security
person".
- Bootloader seeds and RDRAND are generally very difficult if not all
together impossible to audit.
Keep in mind that this doesn't actually change any behavior. This
is just a change in the default Kconfig value. The distros already are
shipping kernels that set things this way.
Ard made an additional argument in [1]:
We're at the mercy of firmware and micro-architecture anyway, given
that we are also relying on it to ensure that every instruction in
the kernel's executable image has been faithfully copied to memory,
and that the CPU implements those instructions as documented. So I
don't think firmware or ISA bugs related to RNGs deserve special
treatment - if they are broken, we should quirk around them like we
usually do. So enabling these by default is a step in the right
direction IMHO.
In [2], Phil pointed out that having this disabled masked a bug that CI
otherwise would have caught:
A clean 5.15.45 boots cleanly, whereas a downstream kernel shows the
static key warning (but it does go on to boot). The significant
difference is that our defconfigs set CONFIG_RANDOM_TRUST_BOOTLOADER=y
defining that on top of multi_v7_defconfig demonstrates the issue on
a clean 5.15.45. Conversely, not setting that option in a
downstream kernel build avoids the warning
set cpu_hwmon as a module build with loongson_sysconf, loongson_chiptemp
undefined error,fix cpu_hwmon compile options to be bool.Some kernel
compilation error information is as follows:
gcc-12 started warning about 'tracker' being used uninitialized:
drivers/net/ethernet/mellanox/mlx5/core/lag/lag.c: In function ‘mlx5_do_bond’:
drivers/net/ethernet/mellanox/mlx5/core/lag/lag.c:786:28: warning: ‘tracker’ is used uninitialized [-Wuninitialized]
786 | struct lag_tracker tracker;
| ^~~~~~~
which seems to be because it doesn't track how the use (and
initialization) is bound by the 'do_bond' flag.
But admittedly that 'do_bond' usage is fairly complicated, and involves
passing it around as an argument to helper functions, so it's somewhat
understandable that gcc doesn't see how that all works.
This function could be rewritten to make the use of that tracker
variable more obviously safe, but for now I'm just adding the forced
initialization of it.
While the concept of checking for dangling pointers to local variables
at function exit is really interesting, the gcc-12 implementation is not
compatible with reality, and results in false positives.
For example, gcc sees us putting things on a local list head allocated
on the stack, which involves exactly those kinds of pointers to the
local stack entry:
In function ‘__list_add’,
inlined from ‘list_add_tail’ at include/linux/list.h:102:2,
inlined from ‘rebuild_snap_realms’ at fs/ceph/snap.c:434:2:
include/linux/list.h:74:19: warning: storing the address of local variable ‘realm_queue’ in ‘*&realm_27(D)->rebuild_item.prev’ [-Wdangling-pointer=]
74 | new->prev = prev;
| ~~~~~~~~~~^~~~~~
But then gcc - understandably - doesn't really understand the big
picture how the doubly linked list works, so doesn't see how we then end
up emptying said list head in a loop and the pointer we added has been
removed.
Gcc also complains about us (intentionally) using this as a way to store
a kind of fake stack trace, eg
drivers/acpi/acpica/utdebug.c:40:38: warning: storing the address of local variable ‘current_sp’ in ‘acpi_gbl_entry_stack_pointer’ [-Wdangling-pointer=]
40 | acpi_gbl_entry_stack_pointer = ¤t_sp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
which is entirely reasonable from a compiler standpoint, and we may want
to change those kinds of patterns, but not not.
So this is one of those "it would be lovely if the compiler were to
complain about us leaving dangling pointers to the stack", but not this
way.
When rx_flag == MTK_RX_FLAGS_HWLRO,
rx_data_len = MTK_MAX_LRO_RX_LENGTH(4096 * 3) > PAGE_SIZE.
netdev_alloc_frag is for alloction of page fragment only.
Reference to other drivers and Documentation/vm/page_frags.rst
Branch to use __get_free_pages when ring->frag_size > PAGE_SIZE.
When len >= INT_MAX - transhdrlen, ulen = len + transhdrlen will be
overflow. To fix, we can follow what udpv6 does and subtract the
transhdrlen from the max.
Similar to the handling of play_deferred in commit 888b5c605018
("Bluetooth: btusb: Fix memory leak in play_deferred"), we thought
a patch might be needed here as well.
Currently usb_submit_urb is called directly to submit deferred tx
urbs after unanchor them.
So the usb_giveback_urb_bh would failed to unref it in usb_unanchor_urb
and cause memory leak.
Put those urbs in tx_anchor to avoid the leak, and also fix the error
handling.
Signed-off-by: Xiaohui Zhang <xiaohuizhang@ruc.edu.cn> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220607083230.6182-1-xiaohuizhang@ruc.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reference must be released when device_register(&vm_cmdline_parent)
failed. Add the corresponding 'put_device()' in the error handling path.
Signed-off-by: chengkaitao <pilgrimtao@gmail.com>
Message-Id: <20220602005542.16489-1-chengkaitao@didiglobal.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix missing resource cleanup (when '(--i) == 0') for error case in
ipr_alloc_mem() and skip incorrect resource cleanup (when '(--i) == 0') for
error case in ipr_request_other_msi_irqs() because variable i started from
1.
Link: https://lore.kernel.org/r/20220529153456.4183738-4-cgxu519@mykernel.net Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Chengguang Xu <cgxu519@mykernel.net> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I'm facing this warning when building for the parisc64 architecture:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function ‘_base_make_ioc_operational’:
drivers/scsi/mpt3sas/mpt3sas_base.c:5396:40: warning: array subscript ‘Mpi2SasIOUnitPage1_t {aka struct _MPI2_CONFIG_PAGE_SASIOUNIT_1}[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds]
5396 | (le16_to_cpu(sas_iounit_pg1->SASWideMaxQueueDepth)) ?
drivers/scsi/mpt3sas/mpt3sas_base.c:5382:26: note: referencing an object of size 20 allocated by ‘kzalloc’
5382 | sas_iounit_pg1 = kzalloc(sz, GFP_KERNEL);
| ^~~~~~~~~~~~~~~~~~~~~~~
The problem is, that only 20 bytes are allocated with kmalloc(), which is
sufficient to hold the bytes which are needed. Nevertheless, gcc complains
because the whole Mpi2SasIOUnitPage1_t struct is 32 bytes in size and thus
doesn't fit into those 20 bytes.
This patch simply allocates all 32 bytes (instead of 20) and thus avoids
the warning. There is no functional change introduced by this patch.
While touching the code I cleaned up to calculation of max_wideport_qd,
max_narrowport_qd and max_sata_qd to make it easier readable.
Test successfully tested on a HP C8000 PA-RISC workstation with 64-bit
kernel.
Link: https://lore.kernel.org/r/YpZ197iZdDZSCzrT@p100 Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NVMe Asynchronous Event Request commands have no command timeout value per
specifications.
Set WQE option to allow a reduced FLUSH polling rate for I/O error
detection specifically for nvme_admin_async_event commands.
Link: https://lore.kernel.org/r/20220603174329.63777-9-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After issuing a LIP, a specific target vendor does not ACC the FLOGI that
lpfc sends. However, it does send its own FLOGI that lpfc ACCs. The
target then establishes the port IDs by sending a PLOGI. lpfc PLOGI_ACCs
and starts the RPI registration for DID 0x000001. The target then sends a
LOGO to the fabric DID. lpfc is currently treating the LOGO from the
fabric DID as a link down and cleans up all the ndlps. The ndlp for DID
0x000001 is put back into NPR and discovery stops, leaving the port in
stuck in bypassed mode.
Change lpfc behavior such that if a LOGO is received for the fabric DID in
PT2PT topology skip the lpfc_linkdown_port() routine and just move the
fabric DID back to NPR.
Link: https://lore.kernel.org/r/20220603174329.63777-7-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A use-after-free crash can occur after an ELS LOGO is aborted.
Specifically, a nodelist structure is freed and then
ndlp->vport->cfg_log_verbose is dereferenced in lpfc_nlp_get() when the
discovery state machine is mistakenly called a second time with
NLP_EVT_DEVICE_RM argument.
Rework lpfc_cmpl_els_logo() to prevent the duplicate calls to release a
nodelist structure.
Link: https://lore.kernel.org/r/20220603174329.63777-6-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
vcpuHint has been expanded to 16 bit on host to enable routing to more
CPUs. Guest side should align with the change. This change has been tested
with hosts with 8-bit and 16-bit vcpuHint, on both platforms host side can
get correct value.
Commit 716fb94772a1 ("Input: soc_button_array - add Lenovo Yoga Tablet2
1051L to the dmi_use_low_level_irq list") added the 1051L to this list
already, but the same problem applies to the 1051F. As there are no
further 1051 variants (just the F/L), we can just DMI match 1051.
Tested on a Lenovo Yoga Tablet2 1051F: Without this patch the
home-button stops working after a wakeup from suspend.
Signed-off-by: Marius Hoch <mail@mariushoch.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220603120246.3065-1-mail@mariushoch.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently wm_adsp_fw_put() returns 0 rather than 1 when updating the value
of the control, meaning that no event is generated to userspace. Fix this
by setting the default return value to 1, the code already exits early with
a return value of 0 if the value is unchanged.
Currently the put() method for the deemphasis control returns 0 when a new
value is written to the control even if the value changed, meaning events
are not generated. Fix this, skip the work of updating the value when it is
unchanged and then return 1 after having done so.
As described in commit d3df91cdc8f9 ("f2fs: Set GF_NOFS in
read_cache_page_gfp while doing f2fs_quota_read"), we must not enter
filesystem reclaim while holding the dq_lock. Prevent this more generally
by using memalloc_nofs_save() while holding the lock.
In an unlikely (and probably wrong?) case that the 'ppi' parameter of
ata_host_alloc_pinfo() points to an array starting with a NULL pointer,
there's going to be a kernel oops as the 'pi' local variable won't get
reassigned from the initial value of NULL. Initialize 'pi' instead to
'&ata_dummy_port_info' to fix the possible kernel oops for good...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kfd_bo_list is used to restore process BOs after
evictions. As page tables could be destroyed during
evictions, we should also update pinned BOs' page tables
during restoring to make sure they are valid.
So for pinned BOs,
1, Validate them and update their page tables.
2, Don't add eviction fence for them.
v2:
- Don't handle pinned ones specially in BO validation.(Felix)
Signed-off-by: Lang Yu <Lang.Yu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The minimum value for the PGA Volume is given as 0x1A, however the
values from there to 0x19 are all the same volume and this is not
represented in the TLV structure. The number of volumes given is correct
so this leads to all the volumes being shifted. Move the minimum value
up to 0x19 to fix this.
A couple of the SX volume controls specify 0x84 as the lowest volume
value, however the correct value from the datasheet is 0x44. The
datasheet don't include spaces in the value it displays as binary so
this was almost certainly just a typo reading 1000100.
Limit the error msg to avoid flooding the console. If you have a lot of
threads hitting this at once, they could have already gotten passed the
dma_debug_disabled() check before they get to the point of allocation
failure, resulting in quite a lot of this error message spamming the
log. Use pr_err_once() to limit that.
Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
MMU notifier callback may pass in mm with mm->mm_users==0 when process
is exiting, use mmget_no_zero to avoid accessing invalid mm in deferred
list work after mm is gone.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We tried to enable the audio on an imx6sx EVB with the codec nau8822,
after setting the internal PLL fractional parameters, the audio still
couldn't work and the there was no sdma irq at all.
After checking with the section "8.1.1 Phase Locked Loop (PLL) Design
Example" of "NAU88C22 Datasheet Rev 0.6", we found we need to
turn off the PLL before programming fractional parameters and turn on
the PLL after programming.
After this change, the audio driver could record and play sound and
the sdma's irq is triggered when playing or recording.
Cc: David Lin <ctlin0@nuvoton.com> Cc: John Hsu <kchsu0@nuvoton.com> Cc: Seven Li <wtli@nuvoton.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20220530040151.95221-2-hui.wang@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory state around the buggy address: d216f800: 00 00 00 00 00 f1 f1 f1 f1 00 00 00 00 00 00 00 d216f880: f2 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>d216f900: 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00
^ d216f980: f2 f2 f2 f2 f2 f2 f2 00 00 00 00 00 00 00 00 00 d216fa00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
After looking into this issue, I find the buggy address belongs
to the task stack region. It seems KASAN has something wrong.
I look into the code of __get_wchan in x86 architecture and
find the same issue has been resolved by the commit 81539dfdd4b7 ("x86/mm, kasan: Silence KASAN warnings in get_wchan()").
The solution could be applied to powerpc architecture too.
As Andrey Ryabinin said, get_wchan() is racy by design, it may
access volatile stack of running task, thus it may access
redzone in a stack frame and cause KASAN to warn about this.
Use READ_ONCE_NOCHECK() to silence these warnings.
Reported-by: Wanming Hu <huwanming@huaweil.com> Signed-off-by: He Ying <heying24@huawei.com> Signed-off-by: Chen Jingwen <chenjingwen6@huawei.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220121014418.155675-1-heying24@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a header for a DB9 serial port, but any attempts to use
hardware handshaking fail. Enable RTS and CTS pin muxing and enable
handshaking in the uart node.
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a header for a DB9 serial port, but any attempts to use
hardware handshaking fail. Enable RTS and CTS pin muxing and enable
handshaking in the uart node.
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nfsd_file nf_rwsem is currently being used to separate file write
and commit instances to ensure that we catch errors and apply them to
the correct write/commit.
We can improve scalability at the expense of a little accuracy (some
extra false positives) by replacing the nf_rwsem with more careful
use of the errseq_t mechanism to track errors across the different
operations.
Commit aa109f9a97dc ("drm/amd/display: Fix DCN3 B0 DP Alt Mapping")
is causing 2nd USB-C display not lighting up.
Phy id remapping is done differently than is assumed in this
patch.
Signed-off-by: Stylon Wang <stylon.wang@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The enumeration of MD_CLEAR in CPUID(EAX=7,ECX=0).EDX{bit 10} is not an
accurate indicator on all CPUs of whether the VERW instruction will
overwrite fill buffers. FB_CLEAR enumeration in
IA32_ARCH_CAPABILITIES{bit 17} covers the case of CPUs that are not
vulnerable to MDS/TAA, indicating that microcode does overwrite fill
buffers.
Guests running in VMM environments may not be aware of all the
capabilities/vulnerabilities of the host CPU. Specifically, a guest may
apply MDS/TAA mitigations when a virtual CPU is enumerated as vulnerable
to MDS/TAA even when the physical CPU is not. On CPUs that enumerate
FB_CLEAR_CTRL the VMM may set FB_CLEAR_DIS to skip overwriting of fill
buffers by the VERW instruction. This is done by setting FB_CLEAR_DIS
during VMENTER and resetting on VMEXIT. For guests that enumerate
FB_CLEAR (explicitly asking for fill buffer clear capability) the VMM
will not use FB_CLEAR_DIS.
Irrespective of guest state, host overwrites CPU buffers before VMENTER
to protect itself from an MMIO capable guest, as part of mitigation for
MMIO Stale Data vulnerabilities.
The Shared Buffers Data Sampling (SBDS) variant of Processor MMIO Stale
Data vulnerabilities may expose RDRAND, RDSEED and SGX EGETKEY data.
Mitigation for this is added by a microcode update.
As some of the implications of SBDS are similar to SRBDS, SRBDS mitigation
infrastructure can be leveraged by SBDS. Set X86_BUG_SRBDS and use SRBDS
mitigation.
Mitigation is enabled by default; use srbds=off to opt-out. Mitigation
status can be checked from below file:
Currently, Linux disables SRBDS mitigation on CPUs not affected by
MDS and have the TSX feature disabled. On such CPUs, secrets cannot
be extracted from CPU fill buffers using MDS or TAA. Without SRBDS
mitigation, Processor MMIO Stale Data vulnerabilities can be used to
extract RDRAND, RDSEED, and EGETKEY data.
Do not disable SRBDS mitigation by default when CPU is also affected by
Processor MMIO Stale Data vulnerabilities.
Add the sysfs reporting file for Processor MMIO Stale Data
vulnerability. It exposes the vulnerability and mitigation state similar
to the existing files for the other hardware vulnerabilities.
When the CPU is affected by Processor MMIO Stale Data vulnerabilities,
Fill Buffer Stale Data Propagator (FBSDP) can propagate stale data out
of Fill buffer to uncore buffer when CPU goes idle. Stale data can then
be exploited with other variants using MMIO operations.
Mitigate it by clearing the Fill buffer before entering idle state.
MDS, TAA and Processor MMIO Stale Data mitigations rely on clearing CPU
buffers. Moreover, status of these mitigations affects each other.
During boot, it is important to maintain the order in which these
mitigations are selected. This is especially true for
md_clear_update_mitigation() that needs to be called after MDS, TAA and
Processor MMIO Stale Data mitigation selection is done.
Introduce md_clear_select_mitigation(), and select all these mitigations
from there. This reflects relationships between these mitigations and
ensures proper ordering.
Processor MMIO Stale Data is a class of vulnerabilities that may
expose data after an MMIO operation. For details please refer to
Documentation/admin-guide/hw-vuln/processor_mmio_stale_data.rst.
These vulnerabilities are broadly categorized as:
Device Register Partial Write (DRPW):
Some endpoint MMIO registers incorrectly handle writes that are
smaller than the register size. Instead of aborting the write or only
copying the correct subset of bytes (for example, 2 bytes for a 2-byte
write), more bytes than specified by the write transaction may be
written to the register. On some processors, this may expose stale
data from the fill buffers of the core that created the write
transaction.
Shared Buffers Data Sampling (SBDS):
After propagators may have moved data around the uncore and copied
stale data into client core fill buffers, processors affected by MFBDS
can leak data from the fill buffer.
Shared Buffers Data Read (SBDR):
It is similar to Shared Buffer Data Sampling (SBDS) except that the
data is directly read into the architectural software-visible state.
An attacker can use these vulnerabilities to extract data from CPU fill
buffers using MDS and TAA methods. Mitigate it by clearing the CPU fill
buffers using the VERW instruction before returning to a user or a
guest.
On CPUs not affected by MDS and TAA, user application cannot sample data
from CPU fill buffers using MDS or TAA. A guest with MMIO access can
still use DRPW or SBDR to extract data architecturally. Mitigate it with
VERW instruction to clear fill buffers before VMENTER for MMIO capable
guests.
Add a kernel parameter mmio_stale_data={off|full|full,nosmt} to control
the mitigation.
Processor MMIO Stale Data mitigation uses similar mitigation as MDS and
TAA. In preparation for adding its mitigation, add a common function to
update all mitigations that depend on MD_CLEAR.
[ bp: Add a newline in md_clear_update_mitigation() to separate
statements better. ]
Processor MMIO Stale Data is a class of vulnerabilities that may
expose data after an MMIO operation. For more details please refer to
Documentation/admin-guide/hw-vuln/processor_mmio_stale_data.rst
Add the Processor MMIO Stale Data bug enumeration. A microcode update
adds new bits to the MSR IA32_ARCH_CAPABILITIES, define them.
Fix a crash that happens if an Rx only socket is created first, then a
second socket is created that is Tx only and bound to the same umem as
the first socket and also the same netdev and queue_id together with the
XDP_SHARED_UMEM flag. In this specific case, the tx_descs array page
pool was not created by the first socket as it was an Rx only socket.
When the second socket is bound it needs this tx_descs array of this
shared page pool as it has a Tx component, but unfortunately it was
never allocated, leading to a crash. Note that this array is only used
for zero-copy drivers using the batched Tx APIs, currently only ice and
i40e.
Detect such case during bind() and allocate this memory region via newly
introduced xp_alloc_tx_descs(). Also, use kvcalloc instead of kcalloc as
for other buffer pool allocations, so that it matches the kvfree() from
xp_destroy().
Fixes: 65e837d98a40 ("i40e: xsk: Move tmp desc array from driver to pool") Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20220425153745.481322-1-maciej.fijalkowski@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting DMA_INTERRUPT capability, a callback function
dma->device_prep_dma_interrupt() is needed to support this capability.
Without setting the callback, dma_async_device_register() will fail dma
capability check.
Commit c60809fae807 ("iov_iter: Fix iter_xarray_get_pages{,_alloc}()")
introduced a problem on some 32-bit architectures (at least arm, xtensa,
csky,sparc and mips), that have a 'size_t' that is 'unsigned int'.
The reason is that we now do
min(nr * PAGE_SIZE - offset, maxsize);
where 'nr' and 'offset' and both 'unsigned int', and PAGE_SIZE is
'unsigned long'. As a result, the normal C type rules means that the
first argument to 'min()' ends up being 'unsigned long'.
In contrast, 'maxsize' is of type 'size_t'.
Now, 'size_t' and 'unsigned long' are always the same physical type in
the kernel, so you'd think this doesn't matter, and from an actual
arithmetic standpoint it doesn't.
But on 32-bit architectures 'size_t' is commonly 'unsigned int', even if
it could also be 'unsigned long'. In that situation, both are unsigned
32-bit types, but they are not the *same* type.
And as a result 'min()' will complain about the distinct types (ignore
the "pointer types" part of the error message: that's an artifact of the
way we have made 'min()' check types for being the same):
lib/iov_iter.c: In function 'iter_xarray_get_pages':
include/linux/minmax.h:20:35: error: comparison of distinct pointer types lacks a cast [-Werror]
20 | (!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
| ^~
lib/iov_iter.c:1464:16: note: in expansion of macro 'min'
1464 | return min(nr * PAGE_SIZE - offset, maxsize);
| ^~~
This was not visible on 64-bit architectures (where we always define
'size_t' to be 'unsigned long').
Force these cases to use 'min_t(size_t, x, y)' to make the type explicit
and avoid the issue.
[ Nit-picky note: technically 'size_t' doesn't have to match 'unsigned
long' arithmetically. We've certainly historically seen environments
with 16-bit address spaces and 32-bit 'unsigned long'.
Similarly, even in 64-bit modern environments, 'size_t' could be its
own type distinct from 'unsigned long', even if it were arithmetically
identical.
So the above type commentary is only really descriptive of the kernel
environment, not some kind of universal truth for the kinds of wild
and crazy situations that are allowed by the C standard ]
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/all/YqRyL2sIqQNDfky2@debian/ Cc: Jeff Layton <jlayton@kernel.org> Cc: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ignoring the explicit_open mount option on mount for devices that do not
have a limit on the number of open zones must be done after the mount
options are parsed and set in s_mount_opts. Move the check to ignore
the explicit_open option after the call to zonefs_parse_options() in
zonefs_fill_super().
Fixes: cd31a9c0dbde ("zonefs: open/close zone on file open/close") Cc: <stable@vger.kernel.org> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a clock imbalance introduced by 8f9487ddf47c ("PCI: qcom: Add support
for SDM845 PCIe controller"), which enables the pipe clock both in init()
and in post_init() but only disables in post_deinit().
Note that the pipe clock was also never disabled in the init() error
paths and that enabling the clock before powering up the PHY looks
questionable.
Link: https://lore.kernel.org/r/20220401133351.10113-1-johan+linaro@kernel.org Fixes: 8f9487ddf47c ("PCI: qcom: Add support for SDM845 PCIe controller") Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: stable@vger.kernel.org # 5.6 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in current Linux, MTU policing does not take into account that packets at
the TC ingress have the L2 header pulled. Thus, the same TC police action
(with the same value of tcfp_mtu) behaves differently for ingress/egress.
In addition, the full GSO size is compared to tcfp_mtu: as a consequence,
the policer drops GSO packets even when individual segments have the L2 +
L3 + L4 + payload length below the configured valued of tcfp_mtu.
Improve the accuracy of MTU policing as follows:
- account for mac_len for non-GSO packets at TC ingress.
- compare MTU threshold with the segmented size for GSO packets.
Also, add a kselftest that verifies the correct behavior.
Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RAID0 layout is irrelevant if all members have the same size so the
array has only one zone. It is *also* irrelevant if the array has two
zones and the second zone has only one device, for example if the array
has two members of different sizes.
So in that case it makes sense to allow assembly even when the layout is
undefined, like what is done when the array has only one zone.
Reviewed-by: NeilBrown <neilb@suse.de> Signed-off-by: Pascal Hambourg <pascal@plouf.fr.eu.org> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than accounting in bytes and multiplying (shifting), we can just
account in bits and avoid the shift. The main motivation for this is
there are other patches in flux that expand this code a bit, and
avoiding the duplication of "* 8" everywhere makes things a bit clearer.
Cc: stable@vger.kernel.org Fixes: 2aea1841598f ("random: credit architectural init the exact amount") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add_bootloader_randomness() and the variables it touches are only used
during __init and not after, so mark these as __init. At the same time,
unexport this, since it's only called by other __init code that's
built-in.
Cc: stable@vger.kernel.org Fixes: 69788ded7904 ("fdt: add support for rng-seed") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if (crng_ready())
...
else if (...)
if (!crng_ready())
...
The second crng_ready() call is redundant, but can't so easily be
optimized out by the compiler.
This commit simplifies that to:
if (crng_ready()
...
else if (...)
...
Fixes: 2248570c88b7 ("random: move initialization functions out of hot pages") Cc: stable@vger.kernel.org Cc: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ptrace PEEKUSR/POKEUSR (aka PEEKUSER/POKEUSER) API allows a process
to read/write registers of another process.
To get/set a register, the API takes an index into an imaginary address
space called the "USER area", where the registers of the process are
laid out in some fashion.
The kernel then maps that index to a particular register in its own data
structures and gets/sets the value.
The API only allows a single machine-word to be read/written at a time.
So 4 bytes on 32-bit kernels and 8 bytes on 64-bit kernels.
The way floating point registers (FPRs) are addressed is somewhat
complicated, because double precision float values are 64-bit even on
32-bit CPUs. That means on 32-bit kernels each FPR occupies two
word-sized locations in the USER area. On 64-bit kernels each FPR
occupies one word-sized location in the USER area.
Internally the kernel stores the FPRs in an array of u64s, or if VSX is
enabled, an array of pairs of u64s where one half of each pair stores
the FPR. Which half of the pair stores the FPR depends on the kernel's
endianness.
To handle the different layouts of the FPRs depending on VSX/no-VSX and
big/little endian, the TS_FPR() macro was introduced.
Unfortunately the TS_FPR() macro does not take into account the fact
that the addressing of each FPR differs between 32-bit and 64-bit
kernels. It just takes the index into the "USER area" passed from
userspace and indexes into the fp_state.fpr array.
On 32-bit there are 64 indexes that address FPRs, but only 32 entries in
the fp_state.fpr array, meaning the user can read/write 256 bytes past
the end of the array. Because the fp_state sits in the middle of the
thread_struct there are various fields than can be overwritten,
including some pointers. As such it may be exploitable.
It has also been observed to cause systems to hang or otherwise
misbehave when using gdbserver, and is probably the root cause of this
report which could not be easily reproduced:
https://lore.kernel.org/linuxppc-dev/dc38afe9-6b78-f3f5-666b-986939e40fc6@keymile.com/
Rather than trying to make the TS_FPR() macro even more complicated to
fix the bug, or add more macros, instead add a special-case for 32-bit
kernels. This is more obvious and hopefully avoids a similar bug
happening again in future.
Note that because 32-bit kernels never have VSX enabled the code doesn't
need to consider TS_FPRWIDTH/OFFSET at all. Add a BUILD_BUG_ON() to
ensure that 32-bit && VSX is never enabled.
Fixes: ef54ff33e7d9 ("powerpc: PTRACE_PEEKUSR/PTRACE_POKEUSER of FPR registers in little endian builds") Cc: stable@vger.kernel.org # v3.13+ Reported-by: Ariel Miculas <ariel.miculas@belden.com> Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220609133245.573565-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supports AV1. Mesa already has support for this and
doesn't rely on the kernel caps for yellow carp, so
this was already working from an application perspective.
Fixes: 3fd1f9fec830 ("amdgpu/nv.c - Added video codec support for Yellow Carp")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2002 Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to change which CRTC is in use for a given
connector/encoder/bridge while we're in self-refresh without fully
disabling the connector/encoder/bridge along the way. This can confuse
the bridge encoder/bridge, because
(a) it needs to track the SR state (trying to perform "active"
operations while the panel is still in SR can be Bad(TM)); and
(b) it tracks the SR state via the CRTC state (and after the switch, the
previous SR state is lost).
Thus, we need to either somehow carry the self-refresh state over to the
new CRTC, or else force an encoder/bridge self-refresh transition during
such a switch.
I choose the latter, so we disable the encoder (and exit PSR) before
attaching it to the new CRTC (where we can continue to assume a clean
(non-self-refresh) state).
This fixes PSR issues seen on Rockchip RK3399 systems with
drivers/gpu/drm/bridge/analogix/analogix_dp_core.c.
Change in v2:
- Drop "->enable" condition; this could possibly be "->active" to
reflect the intended hardware state, but it also is a little
over-specific. We want to make a transition through "disabled" any
time we're exiting PSR at the same time as a CRTC switch.
(Thanks Liu Ying)
Cc: Liu Ying <victor.liu@oss.nxp.com> Cc: <stable@vger.kernel.org> Fixes: 5984c6becf2a ("drm: Add helpers to kick off self refresh mode in drivers") Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220228122522.v2.2.Ic15a2ef69c540aee8732703103e2cff51fb9c399@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most eDP panel functions only work correctly when the panel is not in
self-refresh. In particular, analogix_dp_bridge_disable() tends to hit
AUX channel errors if the panel is in self-refresh.
Given the above, it appears that so far, this driver assumes that we are
never in self-refresh when it comes time to fully disable the bridge.
Prior to commit 05d0461a2741 ("drm/atomic: Try to preserve the crtc
enabled state in drm_atomic_remove_fb, v2."), this tended to be true,
because we would automatically disable the pipe when framebuffers were
removed, and so we'd typically disable the bridge shortly after the last
display activity.
However, that is not guaranteed: an idle (self-refresh) display pipe may
be disabled, e.g., when switching CRTCs. We need to exit PSR first.
Stable notes: this is definitely a bugfix, and the bug has likely
existed in some form for quite a while. It may predate the "PSR helpers"
refactor, but the code looked very different before that, and it's
probably not worth rewriting the fix.
The HAVE_IRQ_EXIT_ON_IRQ_STACK option tells generic code that irq_exit()
is called while still running on the hard irq stack (hardirq_ctx[] in
the powerpc code).
Selecting the option means the generic code will *not* switch to the
softirq stack before running softirqs, because the code is already
running on the (mostly empty) hard irq stack.
But since commit 4ffc24648410 ("powerpc: handle irq_enter/irq_exit in
interrupt handler wrappers"), irq_exit() is now called on the regular task
stack, not the hard irq stack.
That's because previously irq_exit() was called in __do_irq() which is
run on the hard irq stack, but now it is called in
interrupt_async_exit_prepare() which is called from do_irq() constructed
by the wrapper macro, which is after the switch back to the task stack.
So drop HAVE_IRQ_EXIT_ON_IRQ_STACK from the Kconfig. This will mean an
extra stack switch when processing some interrupts, but should
significantly reduce the likelihood of stack overflow.
It also means the softirq stack will be used for running softirqs from
other interrupts that don't use the hard irq stack, eg. timer interrupts.
The bcm5974 driver does the allocation and dma mapping of the usb urb
data buffer, but driver does not set the URB_NO_TRANSFER_DMA_MAP flag
to let usb core know the buffer is already mapped.
usb core tries to map the already mapped buffer, causing a warning:
"xhci_hcd 0000:00:14.0: rejecting DMA map of vmalloc memory"
Fix this by setting the URB_NO_TRANSFER_DMA_MAP, letting usb core
know buffer is already mapped by bcm5974 driver
When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE
bit (VLAN Promiscuous Enable) is set. This means that the VF will
receive packets whose VLAN is not the same than the VLAN of the VF.
If we tcpdump on VF3, we see all the packets, even those transmitted
on vlan 1000.
This behavior prevents to bridge VF1 and VF2 in VM2, because it will
create a loop: packets transmitted on VF1 will be received by VF2 and
vice-versa, and bridged again through the software bridge.
This patch remove the activation of VLAN Promiscuous when a VF enables
the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast
Promiscuous) is kept, so that a VF receives all packets that has the
same VLAN, whatever the destination MAC address.
Fixes: 45ba6082de5d ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a VF requested to remove the promiscuous flag on an interface, the
broadcast packets are not received anymore. This breaks some protocols
like ARP.
In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM
bit (Broadcast Accept) on promiscuous removal.
This flag is already set by default in ixgbe_set_vmolr() on VF reset.
Fixes: 45ba6082de5d ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transaction buffer is allocated by using the size of the packet buf,
and subtracting two which seem intended to remove the two tags which are
not present in the target structure. This calculation leads to under
counting memory because of differences between the packet contents and the
target structure. The aid_len field is a u8 in the packet, but a u32 in
the structure, resulting in at least 3 bytes always being under counted.
Further, the aid data is a variable length field in the packet, but fixed
in the structure, so if this field is less than the max, the difference is
added to the under counting.
The last validation check for transaction->params_len is also incorrect
since it employs the same accounting error.
To fix, perform validation checks progressively to safely reach the
next field, to determine the size of both buffers and verify both tags.
Once all validation checks pass, allocate the buffer and copy the data.
This eliminates freeing memory on the error path, as those checks are
moved ahead of memory allocation.
The first validation check for EVT_TRANSACTION has two different checks
tied together with logical AND. One is a check for minimum packet length,
and the other is for a valid aid_tag. If either condition is true (fails),
then an error should be triggered. The fix is to change && to ||.
Commit 908cbac77d10 ("writeback: Protect inode->i_io_list with
inode->i_lock") made inode->i_io_list not only protected by
wb->list_lock but also inode->i_lock, but inode_io_list_move_locked()
was missed. Add lock there and also update comment describing
things protected by inode->i_lock. This also fixes a race where
__mark_inode_dirty() could move inode under flush worker's hands
and thus sync(2) could miss writing some inodes.
Fixes: 908cbac77d10 ("writeback: Protect inode->i_io_list with inode->i_lock") Link: https://lore.kernel.org/r/20220524150540.12552-1-sunjunchao2870@gmail.com CC: stable@vger.kernel.org Signed-off-by: Jchao Sun <sunjunchao2870@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the first ct() action the packet headers are almost fully
re-written. The next ct() tries to re-use the existing nfct entry
and marks the packet as invalid, so it gets dropped later in the
pipeline.
Clearing the cached conntrack entry whenever packet tuple is changed
to avoid the issue.
The flow key should not be cleared though, because we should still
be able to match on the ct_state if the recirculation happens after
the tuple change but before the next ct() action.
There is a limitation in TI DP83867 PHY device where SGMII AN is only
triggered once after the device is booted up. Even after the PHY TPI is
down and up again, SGMII AN is not triggered and hence no new in-band
message from PHY to MAC side SGMII.
This could cause an issue during power up, when PHY is up prior to MAC.
At this condition, once MAC side SGMII is up, MAC side SGMII wouldn`t
receive new in-band message from TI PHY with correct link status, speed
and duplex info.
As suggested by TI, implemented a SW solution here to retrigger SGMII
Auto-Neg whenever there is a link change.
v2: Add Fixes tag in commit message.
Fixes: 54dd27c45e57 ("net: phy: dp83867: Add TI dp83867 phy") Cc: <stable@vger.kernel.org> # 5.4.x Signed-off-by: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com> Reviewed-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220526090347.128742-1-tee.min.tan@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
The {dma|pio}_mode sysfs files are incorrectly documented as having a
list of the supported DMA/PIO transfer modes, while the corresponding
fields of the *struct* ata_device hold the transfer mode IDs, not masks.
To match these docs, the {dma|pio}_mode (and even xfer_mode!) sysfs
files are handled by the ata_bitfield_name_match() macro which leads to
reading such kind of nonsense from them:
While fixing the file documentation, somewhat reword the {dma|pio}_mode
file doc and add a note about being mostly useful for PATA devices to
the xfer_mode file doc...
Fixes: c26b4896cb0c ("[libata] Add ATA transport class") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating (sealing) a new trusted key, migratable
trusted keys have the FIXED_TPM and FIXED_PARENT attributes
set, and non-migratable keys don't. This is backwards, and
also causes creation to fail when creating a migratable key
under a migratable parent. (The TPM thinks you are trying to
seal a non-migratable blob under a migratable parent.)
The following simple patch fixes the logic, and has been
tested for all four combinations of migratable and non-migratable
trusted keys and parent storage keys. With this logic, you will
get a proper failure if you try to create a non-migratable
trusted key under a migratable parent storage key, and all other
combinations work correctly.
Cc: stable@vger.kernel.org # v5.13+ Fixes: ad3090d17dae ("security: keys: trusted: Make sealed key properly interoperable") Signed-off-by: David Safford <david.safford@gmail.com> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cifs.ko defines two file system types: cifs & smb3, and
__cifs_get_super() was not including smb3 file system type when
looking up superblocks, therefore failing to reconnect tcons in
cifs_tree_connect().
Fix this by calling iterate_supers_type() on both file system types.
Link: https://lore.kernel.org/r/CAFrh3J9soC36+BVuwHB=g9z_KB5Og2+p2_W+BBoBOZveErz14w@mail.gmail.com Cc: stable@vger.kernel.org Tested-by: Satadru Pramanik <satadru@gmail.com> Reported-by: Satadru Pramanik <satadru@gmail.com> Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During reconnects, we check the return value from
cifs_negotiate_protocol, and have handlers for both success
and failures. But if that passes, and cifs_setup_session
returns any errors other than -EACCES, we do not handle
that. This fix adds a handler for that, so that we don't
go ahead and try a tree_connect on a failed session.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log