The hardware expects FrameNumWrap or long_term_frame_idx. Picture
numbers are per field, and are mostly used during the memory
management process, which is done in userland. This fixes two
ITU conformance tests:
- MR6_BT_B
- MR8_BT_B
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
smartshift apu and dgpu power boost are reported as percentage
with respect to their power limits. adjust the units of power before
calculating the percentage of boost.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
smartshift apu and dgpu power boost are reported as percentage with
respect to their power limits. This value[0-100] reflects the boost
for the respective device.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When userspace closes the socket before sending a disconnect
request, the following I/O requests will be blocked in
wait_for_reconnect() until dead timeout. This will cause the
following disconnect request also hung on blk_mq_quiesce_queue().
That means we have no way to disconnect a nbd device if there
are some I/O requests waiting for reconnecting until dead timeout.
It's not expected. So let's wake up the thread waiting for
reconnecting directly when a disconnect request is sent.
There is a logic error when removing rt5645 device as the function
rt5645_i2c_remove() first cancel the &rt5645->jack_detect_work and
delete the &rt5645->btn_check_timer latter. However, since the timer
handler rt5645_btn_check_callback() will re-queue the jack_detect_work,
this cleanup order is buggy.
That is, once the del_timer_sync in rt5645_i2c_remove is concurrently
run with the rt5645_btn_check_callback, the canceled jack_detect_work
will be rescheduled again, leading to possible use-after-free.
This patch fix the issue by placing the del_timer_sync function before
the cancel_delayed_work_sync.
In nvme_alloc_admin_tags, the admin_q can be set to an error (typically
-ENOMEM) if the blk_mq_init_queue call fails to set up the queue, which
is checked immediately after the call. However, when we return the error
message up the stack, to nvme_reset_work the error takes us to
nvme_remove_dead_ctrl()
nvme_dev_disable()
nvme_suspend_queue(&dev->queues[0]).
Here, we only check that the admin_q is non-NULL, rather than not
an error or NULL, and begin quiescing a queue that never existed, leading
to bad / NULL pointer dereference.
Signed-off-by: Kyle Smith <kyles@hpe.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to measure the boot process, the timer should be switched on as
early in boot as possible. As well, the commit defines the get_cycles
macro, like the previous patches in this series, so that generic code is
aware that it's implemented by the platform, as is done on other archs.
Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jonas Bonn <jonas@southpole.se> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Stafford Horne <shorne@gmail.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit made binding and unbinding of USB Ethernet asymmetrical:
Before, usbnet_probe() first invoked the ->bind() callback and then
register_netdev(). usbnet_disconnect() mirrored that by first invoking
unregister_netdev() and then ->unbind().
Since the commit, the order in usbnet_disconnect() is reversed and no
longer mirrors usbnet_probe().
One consequence is that a PHY disconnected (and stopped) in ->unbind()
is afterwards stopped once more by unregister_netdev() as it closes the
netdev before unregistering. That necessitates a contortion in ->stop()
because the PHY may only be stopped if it hasn't already been
disconnected.
Reverting the commit allows making the call to phy_stop() unconditional
in ->stop().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500 Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514 Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Oliver Neukum <oneukum@suse.com> Cc: Martyn Welch <martyn.welch@collabora.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an adapter is trying to claim a free logical address then it is
in the 'is_configuring' state. If during that process the cable is
disconnected (HPD goes low, which in turn invalidates the physical
address), then cec_adap_unconfigure() is called, and that set the
is_configuring boolean to false, even though the thread that's
trying to claim an LA is still running.
Don't touch the is_configuring bool in cec_adap_unconfigure(), it
will eventually be cleared by the thread. By making that change
the cec_config_log_addr() function also had to change: it was
aborting if is_configuring became false (since that is what
cec_adap_unconfigure() did), but that no longer works. Instead
check if the physical address is invalid. That is a much
more appropriate check anyway.
This fixes a bug where the the adapter could be disabled even
though the device was still configuring. This could cause POLL
transmits to time out.
Since usb_register_dev() from imon_init_display() from imon_probe() holds
minor_rwsem while display_open() which holds driver_lock and ictx->lock is
called with minor_rwsem held from usb_open(), holding driver_lock or
ictx->lock when calling usb_register_dev() causes circular locking
dependency problem.
Since usb_deregister_dev() from imon_disconnect() holds minor_rwsem while
display_open() which holds driver_lock is called with minor_rwsem held,
holding driver_lock when calling usb_deregister_dev() also causes circular
locking dependency problem.
Sean Young explained that the problem is there are imon devices which have
two usb interfaces, even though it is one device. The probe and disconnect
function of both usb interfaces can run concurrently.
Alan Stern responded that the driver and USB cores guarantee that when an
interface is probed, both the interface and its USB device are locked.
Ditto for when the disconnect callback gets run. So concurrent probing/
disconnection of multiple interfaces on the same device is not possible.
Therefore, we don't need locks for handling race between imon_probe() and
imon_disconnect(). But we still need to handle race between display_open()
/vfd_write()/lcd_write()/display_close() and imon_disconnect(), for
disconnect event can happen while file descriptors are in use.
Since "struct file"->private_data is set by display_open(), vfd_write()/
lcd_write()/display_close() can assume that "struct file"->private_data
is not NULL even after usb_set_intfdata(interface, NULL) was called.
Replace insufficiently held driver_lock with refcount_t based management.
Add a boolean flag for recording whether imon_disconnect() was already
called. Use RCU for accessing this boolean flag and refcount_t.
Since the boolean flag for imon_disconnect() is shared, disconnect event
on either intf0 or intf1 affects both interfaces. But I assume that this
change does not matter, for usually disconnect event would not happen
while interfaces are in use.
Link: https://syzkaller.appspot.com/bug?extid=c558267ad910fc494497 Reported-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Tested-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Always set pps_cb_qp_offset and pps_cr_qp_offset values in Hantro/G2
register whatever is V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT
flag value.
The vendor code does the same to set these values.
This fixes conformance test CAINIT_G_SHARP_3.
Fluster HEVC score is increase by one with this patch.
Let VIDIOC_ENUM_FRAMEINTERVALS return -EINVAL if userspace queries
frame intervals for frame sizes unsupported by the encoder. Fixes the
following v4l2-compliance failure:
fail: v4l2-test-formats.cpp(123): found frame intervals for invalid size 47x16
fail: v4l2-test-formats.cpp(282): node->codec_mask & STATEFUL_ENCODER
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
[hverkuil: drop incorrect 'For decoder devices, return -ENOTTY.' in the commit log]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver needs to check if the format is 802.2 vs 802.3 in order to set
a tx descriptor flag. skb->protocol can't be used, since it may not be properly
initialized for packets coming in from a packet socket.
Fix misdetection by checking the ethertype from the skb data instead
Even though it's not possible to get into the SSIF_GETTING_MESSAGES and
SSIF_GETTING_EVENTS states without a valid message in the msg field,
it's probably best to be defensive here and check and print a log, since
that means something else went wrong.
Also add a default clause to that switch statement to release the lock
and print a log, in case the state variable gets messed up somehow.
ASUS B1400CEAE fails to resume from suspend to idle by default. This was
bisected back to commit 5a915aa99ecb ("nvme-pci: add support for ACPI
StorageD3Enable property") but this is a red herring to the problem.
Before this commit the system wasn't getting into deepest sleep state.
Presumably this commit is allowing entry into deepest sleep state as
advertised by firmware, but there are some other problems related to
the wakeup.
As it is confirmed the system works properly with S3, set the default for
this system to S3.
Reported-by: Jian-Hong Pan <jhp@endlessos.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215742 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Jian-Hong Pan <jhp@endlessos.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We observed the error "cacheline tracking ENOMEM, dma-debug disabled"
during a light system load (copying some files). The reason for this error
is that the dma_active_cacheline radix tree uses GFP_NOWAIT allocation -
so it can't access the emergency memory reserves and it fails as soon as
anybody reaches the watermark.
This patch changes GFP_NOWAIT to GFP_ATOMIC, so that it can access the
emergency memory reserves.
When we use raw_spin_rq_lock() to acquire the rq lock and have to
update the rq clock while holding the lock, the kernel may issue
a WARN_DOUBLE_CLOCK warning.
Since we directly use raw_spin_rq_lock() to acquire rq lock instead of
rq_lock(), there is no corresponding change to rq->clock_update_flags.
In particular, we have obtained the rq lock of other CPUs, the
rq->clock_update_flags of this CPU may be RQCF_UPDATED at this time, and
then calling update_rq_clock() will trigger the WARN_DOUBLE_CLOCK warning.
So we need to clear RQCF_UPDATED of rq->clock_update_flags to avoid
the WARN_DOUBLE_CLOCK warning.
For the sched_rt_period_timer() and migrate_task_rq_dl() cases
we simply replace raw_spin_rq_lock()/raw_spin_rq_unlock() with
rq_lock()/rq_unlock().
For the {pull,push}_{rt,dl}_task() cases, we add the
double_rq_clock_clear_update() function to clear RQCF_UPDATED of
rq->clock_update_flags, and call double_rq_clock_clear_update()
before double_lock_balance()/double_rq_lock() returns to avoid the
WARN_DOUBLE_CLOCK warning.
Steps to reproduce:
1. Enable CONFIG_SCHED_DEBUG when compiling the kernel
2. echo 1 > /sys/kernel/debug/clear_warn_once
echo "WARN_DOUBLE_CLOCK" > /sys/kernel/debug/sched/features
echo "NO_RT_PUSH_IPI" > /sys/kernel/debug/sched/features
3. Run some rt/dl tasks that periodically work and sleep, e.g.
Create 2*n rt or dl (90% running) tasks via rt-app (on a system
with n CPUs), and Dietmar Eggemann reports Call Trace 4 when running
on PREEMPT_RT kernel.
gcc 12 does not (always) optimize away code that should only be generated
if parameters are constant and within in a certain range. This depends on
various obscure kernel config options, however in particular
PROFILE_ALL_BRANCHES can trigger this compile error:
In function ‘__atomic_add_const’,
inlined from ‘__preempt_count_add.part.0’ at ./arch/s390/include/asm/preempt.h:50:3:
./arch/s390/include/asm/atomic_ops.h:80:9: error: impossible constraint in ‘asm’
80 | asm volatile( \
| ^~~
Workaround this by simply disabling the optimization for
PROFILE_ALL_BRANCHES, since the kernel will be so slow, that this
optimization won't matter at all.
Reported-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I have a syzbot report that managed to get a crash in skb_checksum_help()
If syzbot can trigger these BUG(), it makes sense to replace
them with more friendly WARN_ON_ONCE() since skb_checksum_help()
can instead return an error code.
Note that syzbot will still crash there, until real bug is fixed.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When configuring CMF management based on signals instead of FPINs, FPIN
alarm and warning statistics are not tracked.
Change the behavior so that FPIN alarms and warnings are always tracked
regardless of the configured mode.
Similar changes are made in the CMF signal stat accounting logic. Upon
receipt of a signal, only track signaled alarms and warnings. FPIN stats
should not be incremented upon receipt of a signal.
Link: https://lore.kernel.org/r/20220506035519.50908-11-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The endianness flag is used on the CODEC side to specify an
ambivalence to endian, typically because it is lost over the hardware
link. This device receives audio over an I2S DAI and as such should
have endianness applied.
A fixup is also required to use the width directly rather than relying
on the format in hw_params, now both little and big endian would be
supported. It is worth noting this changes the behaviour of S24_LE to
use a word length of 24 rather than 32. This would appear to be a
correction since the fact S24_LE is stored as 32 bits should not be
presented over the bus.
When "crashkernel=X,high" is used, there may be two crash regions:
high=crashk_res and low=crashk_low_res. But now the syscall
kexec_file_load() only add crashk_res into "linux,usable-memory-range",
this may cause the second kernel to have no available dma memory.
Fix it like kexec-tools does for option -c, add both 'high' and 'low'
regions into the dtb.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Baoquan He <bhe@redhat.com> Link: https://lore.kernel.org/r/20220506114402.365-6-thunder.leizhen@huawei.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a slab-out-of-bounds Write bug in hid-bigbenff driver.
The problem is the driver assumes the device must have an input but
some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
The MT6315 PMIC dt-binding should enforce that one of the valid
regulator-compatible is set in each regulator node. However it was
mistakenly matching against regulator-name instead.
Fix the typo. This not only fixes the compatible verification, but also
lifts the regulator-name restriction, so that more meaningful names can
be set for each platform.
When psp_hw_init failed, it will set the load_type to AMDGPU_FW_LOAD_DIRECT.
During amdgpu_device_ip_fini, amdgpu_ucode_free_bo checks that load_type is
AMDGPU_FW_LOAD_DIRECT and skips deallocating fw_buf causing memory leak.
Remove load_type check in amdgpu_ucode_free_bo.
Signed-off-by: Alice Wong <shiwei.wong@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocations should be done in sw_init. hw_init should
just be hardware programming needed to initialize the IP block.
This is how most other IP blocks work. Move the GPU memory
allocations from psp hw_init to psp sw_init and move the memory
free to sw_fini. This also fixes a potential GPU memory leak
if psp hw_init fails.
When trapping packets for on-CPU processing, Spectrum machines
differentiate between control and non-control traps. Traffic trapped
through non-control traps is treated as data and kept in shared buffer in
pools 0-4. Traffic trapped through control traps is kept in the dedicated
control buffer 9. The advantage of marking traps as control is that
pressure in the data plane does not prevent the control traffic to be
processed.
When the LLDP trap was introduced, it was marked as a control trap. But
then in commit 9418ff8b1952 ("mlxsw: spectrum: PTP: Hook into packet
receive path"), PTP traps were introduced. Because Ethernet-encapsulated
PTP packets look to the Spectrum-1 ASIC as LLDP traffic and are trapped
under the LLDP trap, this trap was reconfigured as non-control, in sync
with the PTP traps.
There is however no requirement that PTP traffic be handled as data.
Besides, the usual encapsulation for PTP traffic is UDP, not bare Ethernet,
and that is in deployments that even need PTP, which is far less common
than LLDP. This is reflected by the default policer, which was not bumped
up to the 19Kpps / 24Kpps that is the expected load of a PTP-enabled
Spectrum-1 switch.
Marking of LLDP trap as non-control was therefore probably misguided. In
this patch, change it back to control.
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The idea behind the warnings is that the user would get warned in case when
more than one priority is configured for a given DSCP value on a netdevice.
The warning is currently wrong, because dcb_ieee_getapp_mask() returns
the first matching entry, not all of them, and the warning will then claim
that some priority is "current", when in fact it is not.
But more importantly, the warning is misleading in general. Consider the
following commands:
# dcb app flush dev swp19 dscp-prio
# dcb app add dev swp19 dscp-prio 24:3
# dcb app replace dev swp19 dscp-prio 24:2
The last command will issue the following warning:
mlxsw_spectrum3 0000:07:00.0 swp19: Ignoring new priority 2 for DSCP 24 in favor of current value of 3
The reason is that the "replace" command works by first adding the new
value, and then removing all old values. This is the only way to make the
replacement without causing the traffic to be prioritized to whatever the
chip defaults to. The warning is issued in response to adding the new
priority, and then no warning is shown when the old priority is removed.
The upshot is that the canonical way to change traffic prioritization
always produces a warning about ignoring the new priority, but what gets
configured is in fact what the user intended.
An option to just emit warning every time that the prioritization changes
just to make it clear that it happened is obviously unsatisfactory.
Therefore, in this patch, remove the warnings.
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
DAPM tracks and reports the value presented to the user from DAPM controls
separately to the register value, these may diverge during initialisation
or when an autodisable control is in use.
When writing DAPM controls we currently report that a change has occurred
if either the DAPM value or the value stored in the register has changed,
meaning that if the two are out of sync we may appear to report a spurious
event to userspace. Since we use this folded in value for nothing other
than the value reported to userspace simply drop the folding in of the
register change.
When an FTE has no children is means all the rules where removed
and the FTE can be deleted regardless of the dests_size value.
While dests_size should be 0 when there are no children
be extra careful not to leak memory or get firmware syndrome
if the proper bookkeeping of dests_size wasn't done.
Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When tcmu_vma_fault() gets a page successfully, before the current context
completes page fault procedure, find_free_blocks() may run and call
unmap_mapping_range() to unmap the page. Assume that when
find_free_blocks() initially completes and the previous page fault
procedure starts to run again and completes, then one truncated page has
been mapped to userspace. But note that tcmu_vma_fault() has gotten a
refcount for the page so any other subsystem won't be able to use the page
unless the userspace address is unmapped later.
If another command subsequently runs and needs to extend dbi_thresh it may
reuse the corresponding slot for the previous page in data_bitmap. Then
though we'll allocate new page for this slot in data_area, no page fault
will happen because we have a valid map and the real request's data will be
lost.
Filesystem implementations will also run into this issue but they usually
lock the page when vm_operations_struct->fault gets a page and unlock the
page after finish_fault() completes. For truncate filesystems lock pages in
truncate_inode_pages() to protect against racing wrt. page faults.
To fix this possible data corruption scenario we can apply a method similar
to the filesystems. For pages that are to be freed, tcmu_blocks_release()
locks and unlocks. Make tcmu_vma_fault() also lock found page under
cmdr_lock. At the same time, since tcmu_vma_fault() gets an extra page
refcount, tcmu_blocks_release() won't free pages if pages are in page fault
procedure, which means it is safe to call tcmu_blocks_release() before
unmap_mapping_range().
With these changes tcmu_blocks_release() will wait for all page faults to
be completed before calling unmap_mapping_range(). And later, if
unmap_mapping_range() is called, it will ensure stale mappings are removed.
If a compat process tries to execute an unknown system call above the
__ARM_NR_COMPAT_END number, the kernel sends a SIGILL signal to the
offending process. Information about the error is printed to dmesg in
compat_arm_syscall() -> arm64_notify_die() -> arm64_force_sig_fault() ->
arm64_show_signal().
arm64_show_signal() interprets a non-zero value for
current->thread.fault_code as an exception syndrome and displays the
message associated with the ESR_ELx.EC field (bits 31:26).
current->thread.fault_code is set in compat_arm_syscall() ->
arm64_notify_die() with the bad syscall number instead of a valid ESR_ELx
value. This means that the ESR_ELx.EC field has the value that the user set
for the syscall number and the kernel can end up printing bogus exception
messages*. For example, for the syscall number 0x68000000, which evaluates
to ESR_ELx.EC value of 0x1A (ESR_ELx_EC_FPAC) the kernel prints this error:
which is misleading, as the bad compat syscall has nothing to do with
pointer authentication.
Stop arm64_show_signal() from printing exception syndrome information by
having compat_arm_syscall() set the ESR_ELx value to 0, as it has no
meaning for an invalid system call number. The example above now becomes:
which although shows less information because the syscall number,
wrongfully advertised as the ESR value, is missing, it is better than
showing plainly wrong information. The syscall number can be easily
obtained with strace.
*A 32-bit value above or equal to 0x8000_0000 is interpreted as a negative
integer in compat_arm_syscal() and the condition scno < __ARM_NR_COMPAT_END
evaluates to true; the syscall will exit to userspace in this case with the
ENOSYS error code instead of arm64_notify_die() being called.
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Reported-by: kernel test robot <lkp@intel.com> CC: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the check for format_count > 64 in __drm_universal_plane_init()
shouldn't be hit (it's a WARN_ON), in its current position it will then
leak the plane->format_types array and fail to call
drm_mode_object_unregister() leaking the modeset identifier. Move it to
the start of the function to avoid allocating those resources in the
first place.
Add a quirk for the HP Pro Tablet 408, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
It also uses DMIC1 for the internal mic rather then the default IN3
and it uses JD2 rather then the default JD1 for jack-detect.
If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a
received frame, the frame is dropped and resources are leaked.
Fix by returning resources when discarding an unhandled frame type. Update
lpfc_fc_frame_check() handling of NOP basic link service.
Link: https://lore.kernel.org/r/20220426181419.9154-1-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync() and
pm_runtime_put_noidle(). This change is just to simplify the code, no
actual functional changes.
This patch fixes the issue where the driver miscomputes the 64-bit
values of the wptr of the SDMA doorbell when initializing the
hardware. SDMA engines v4 and later on have full 64-bit registers for
wptr thus they should be set properly.
Older generation hardwares like CIK / SI have only 16 / 20 / 24bits
for the WPTR, where the calls of lower_32_bits() will be removed in a
following patch.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Haohui Mai <ricetons@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If major equals 0, register_chrdev() returns an error code when it fails.
This function dynamically allocates a major and returns its number on
success, so we should use "< 0" to check it instead of "!".
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit 7eb40ca8c49b ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Do what is done in other DMA-enabled MMC host drivers (cf. host/mmci.c) and
limit the maximum segment size based on the DMA engine's capabilities. This
is needed to avoid warnings like the following with CONFIG_DMA_API_DEBUG=y.
If bitmap area contains invalid data, kernel will crash then mdadm
triggers "Segmentation fault".
This is cluster-md speical bug. In non-clustered env, mdadm will
handle broken metadata case. In clustered array, only kernel space
handles bitmap slot info. But even this bug only happened in clustered
env, current sanity check is wrong, the code should be changed.
In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't
block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T()
trigger "divide error".
When the driver fails to call the dma_set_mask(), the driver will get
the following splat:
[ 55.853884] BUG: KASAN: use-after-free in __process_removed_driver+0x3c/0x240
[ 55.854486] Read of size 8 at addr ffff88810de60408 by task modprobe/590
[ 55.856822] Call Trace:
[ 55.860327] __process_removed_driver+0x3c/0x240
[ 55.861347] bus_for_each_dev+0x102/0x160
[ 55.861681] i2c_del_driver+0x2f/0x50
This is because the driver has initialized the i2c related resources
in cx23885_dev_setup() but not released them in error handling, fix this
bug by modifying the error path that jumps after failing to call the
dma_set_mask().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If venus_probe fails at pm_runtime_put_sync the error handling first
calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets
core->ops to NULL, hfi_core_deinit cannot call the core_deinit function
anymore.
Avoid this null pointer derefence by skipping the call when necessary.
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
commit cbbe4a2ca0ff00 ("ASoC: rsnd: tidyup
rsnd_ssiu_busif_err_status_clear()") merged duplicate code, but it didn't
care about default case, and causes smatch warnings.
smatch warnings:
sound/soc/sh/rcar/ssiu.c:112 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'offset'.
sound/soc/sh/rcar/ssiu.c:114 rsnd_ssiu_busif_err_status_clear() \
error: uninitialized symbol 'shift'.
This patch cares it.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87r15rgn6p.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function si_parse_power_table(), array adev->pm.dpm.ps and its member
is allocated. If the allocation of each member fails, the array itself
is freed and returned with an error code. However, the array is later
freed again in si_dpm_fini() function which is called when the function
returns an error.
This leads to potential double free of the array adev->pm.dpm.ps, as
well as leak of its array members, since the members are not freed in
the allocation function and the array is not nulled when freed.
In addition adev->pm.dpm.num_ps, which keeps track of the allocated
array member, is not updated until the member allocation is
successfully finished, this could also lead to either use after free,
or uninitialized variable access in si_dpm_fini().
Fix this by postponing the free of the array until si_dpm_fini() and
increment adev->pm.dpm.num_ps everytime the array member is allocated.
When PSCI OSI mode is supported the syscore flag is set for the CPU devices
that becomes attached to their PM domains (genpds). In the suspend-to-idle
case, we call dev_pm_genpd_suspend|resume() to allow genpd to properly
manage the power-off/on operations (pick an idlestate and manage the on/off
notifications).
For suspend-to-ram, dev_pm_genpd_suspend|resume() is currently not being
called, which causes a problem that the genpd on/off notifiers do not get
sent as expected. This prevents the platform-specific operations from being
executed, typically needed just before/after the boot CPU is being turned
off/on.
To deal with this problem, let's register a syscore ops for cpuidle-psci
when PSCI OSI mode is being used and call dev_pm_genpd_suspend|resume()
from them. In this way, genpd regains control of the PM domain topology and
then sends the on/off notifications when it's appropriate.
Reported-by: Maulik Shah <quic_mkshah@quicinc.com> Suggested-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Maulik Shah <quic_mkshah@quicinc.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
this_cpu_ptr() calls smp_processor_id() in a preemptible context.
Fix by using per_cpu_ptr() with raw_smp_processor_id() instead.
Link: https://lore.kernel.org/r/20220412222008.126521-16-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in
lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock
first before phba->hbalock.
Link: https://lore.kernel.org/r/20220412222008.126521-7-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The same CPU tries to claim the phba->port_list_lock twice.
Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and
lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need
to take the phba->port_list_lock within lpfc_dmp_dbg().
Link: https://lore.kernel.org/r/20220412222008.126521-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Suggested-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible when using ASoC that input_dev is unregistered while
calling snd_jack_report, which causes NULL pointer dereference.
In order to prevent this serialize access to input_dev using mutex lock.
The TASKS_RUDE_RCU does not select IRQ_WORK, which can result in build
failures for kernels that do not otherwise select IRQ_WORK. This commit
therefore causes the TASKS_RUDE_RCU Kconfig option to select IRQ_WORK.
Reported-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit therefore fixes this issue by applying a single-CPU
optimization to the RCU Tasks Rude grace-period process. The key point
here is that the purpose of this RCU flavor is to force a schedule on
each online CPU since some past event. But the rcu_tasks_rude_wait_gp()
function runs in the context of the RCU Tasks Rude's grace-period kthread,
so there must already have been a context switch on the current CPU since
the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude().
So if there is only a single CPU online, RCU Tasks Rude's grace-period
kthread does not need to anything at all.
It turns out that the rcu_tasks_rude_wait_gp() function's call to
schedule_on_each_cpu() causes problems during early boot. During that
time, there is only one online CPU, namely the boot CPU. Therefore,
applying this single-CPU optimization fixes early-boot instances of
this problem.
If drm_universal_plane_init() fails early we jump to the common cleanup code
that calls komeda_plane_destroy() which in turn could access the uninitalised
drm_plane and crash. Return early if an error is detected without going through
the common code.
Using an ath9k card the debugfs output of minstrel_ht looks like the following
(note the zero values for the first four rates sum-of success/attempts):
Total packet count:: ideal 16582 lookaround 885
Average # of aggregated frames per A-MPDU: 1.0
Debugging showed that the rate statistics for the first four rates where
stored in the MINSTREL_CCK_GROUP instead of the MINSTREL_OFDM_GROUP because
in minstrel_ht_get_stats() the supported check was not honoured as done in
various other places, e.g net/mac80211/rc80211_minstrel_ht_debugfs.c:
While running inside virtual machine, the kernel can bypass cache
flushing. Changing sleep state in a virtual machine doesn't affect the
host system sleep state and cannot lead to data loss.
Before entering sleep states, the ACPI code flushes caches to prevent
data loss using the WBINVD instruction. This mechanism is required on
bare metal.
But, any use WBINVD inside of a guest is worthless. Changing sleep
state in a virtual machine doesn't affect the host system sleep state
and cannot lead to data loss, so most hypervisors simply ignore it.
Despite this, the ACPI code calls WBINVD unconditionally anyway.
It's useless, but also normally harmless.
In TDX guests, though, WBINVD stops being harmless; it triggers a
virtualization exception (#VE). If the ACPI cache-flushing WBINVD
were left in place, TDX guests would need handling to recover from
the exception.
Avoid using WBINVD whenever running under a hypervisor. This both
removes the useless WBINVDs and saves TDX from implementing WBINVD
handling.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20220405232939.73860-30-kirill.shutemov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The UV5 platform synchronizes the TSCs among all chassis, and will not
proceed to OS boot without achieving synchronization. Previous UV
platforms provided a register indicating successful synchronization.
This is no longer available on UV5. On this platform TSC_ADJUST
should not be reset by the kernel.
Signed-off-by: Mike Travis <mike.travis@hpe.com> Signed-off-by: Steve Wahl <steve.wahl@hpe.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Dimitri Sivanich <dimitri.sivanich@hpe.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220406195149.228164-3-steve.wahl@hpe.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This shouldn't be a problem in practice since until we've actually
taken over the console there's nothing we've registered with the
console/vt subsystem, so the exit/unbind path that check this can't
do the wrong thing. But it's confusing, so fix it by moving it a tad
later.
Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Du Cheng <ducheng2@gmail.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Claudio Suarez <cssk@net-c.es> Cc: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220405210335.3434130-14-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <sashal@kernel.org>
idev->addr_list needs to be protected by idev->lock. However, it is not
always possible to do so while iterating and performing actions on
inet6_ifaddr instances. For example, multiple functions (like
addrconf_{join,leave}_anycast) eventually call down to other functions
that acquire the idev->lock. The current code temporarily unlocked the
idev->lock during the loops, which can cause race conditions. Moving the
locks up is also not an appropriate solution as the ordering of lock
acquisition will be inconsistent with for example mc_lock.
This solution adds an additional field to inet6_ifaddr that is used
to temporarily add the instances to a temporary list while holding
idev->lock. The temporary list can then be traversed without holding
idev->lock. This change was done in two places. In addrconf_ifdown, the
list_for_each_entry_safe variant of the list loop is also no longer
necessary as there is no deletion within that specific loop.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220403231523.45843-1-dossche.niels@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
The script for checking that various lists of types in bpftool remain in
sync with the UAPI BPF header uses a regex to parse enum bpf_prog_type.
If this enum contains a set of values different from the list of program
types in bpftool, it complains.
This script should have reported the addition, some time ago, of the new
BPF_PROG_TYPE_SYSCALL, which was not reported to bpftool's program types
list. It failed to do so, because it failed to parse that new type from
the enum. This is because the new value, in the BPF header, has an
explicative comment on the same line, and the regex does not support
that.
Let's update the script to support parsing enum values when they have
comments on the same line.
Since commit c2f0b56af237 ("namei: prepare for idmapped mounts")
vfs_link's prototype was changed, the kprobe definition in
profiler selftest in turn wasn't updated. The result is that all
argument after the first are now stored in different registers. This
means that self-test has been broken ever since. Fix it by updating the
kprobe definition accordingly.
The kms code wasn't validating the modifiers and was letting through
unsupported formats. rgb8 was never properly supported and has no
matching svga screen target format so remove it.
This fixes format/modifier failures in kms_addfb_basic from IGT.
The VT-d spec requires (10.4.4 Global Command Register, TE
field) that:
Hardware implementations supporting DMA draining must drain
any in-flight DMA read/write requests queued within the
Root-Complex before completing the translation enable
command and reflecting the status of the command through
the TES field in the Global Status register.
Unfortunately, some integrated graphic devices fail to do
so after some kind of power state transition. As the
result, the system might stuck in iommu_disable_translati
on(), waiting for the completion of TE transition.
This adds RPLS to a quirk list for those devices and skips
TE disabling if the qurik hits.
[BUG]
Test case generic/475 have a very high chance (almost 100%) to hit a fs
hang, where a data page will never be unlocked and hang all later
operations.
[CAUSE]
In btrfs_do_readpage(), if we hit an error from submit_extent_page() we
will try to do the cleanup for our current io range, and exit.
This works fine for PAGE_SIZE == sectorsize cases, but not for subpage.
For subpage btrfs_do_readpage() will lock the full page first, which can
contain several different sectors and extents:
btrfs_do_readpage()
|- begin_page_read()
| |- btrfs_subpage_start_reader();
| Now the page will have PAGE_SIZE / sectorsize reader pending,
| and the page is locked.
|
|- end_page_read() for different branches
| This function will reduce subpage readers, and when readers
| reach 0, it will unlock the page.
But when submit_extent_page() failed, we only cleanup the current
io range, while the remaining io range will never be cleaned up, and the
page remains locked forever.
[FIX]
Update the error handling of submit_extent_page() to cleanup all the
remaining subpage range before exiting the loop.
Please note that, now submit_extent_page() can only fail due to
sanity check in alloc_new_bio().
Thus regular IO errors are impossible to trigger the error path.
[BUG]
There is a report that a btrfs has a bad super block num devices.
This makes btrfs to reject the fs completely.
BTRFS error (device sdd3): super_num_devices 3 mismatch with num_devices 2 found here
BTRFS error (device sdd3): failed to read chunk tree: -22
BTRFS error (device sdd3): open_ctree failed
[CAUSE]
During btrfs device removal, chunk tree and super block num devs are
updated in two different transactions:
btrfs_rm_device()
|- btrfs_rm_dev_item(device)
| |- trans = btrfs_start_transaction()
| | Now we got transaction X
| |
| |- btrfs_del_item()
| | Now device item is removed from chunk tree
| |
| |- btrfs_commit_transaction()
| Transaction X got committed, super num devs untouched,
| but device item removed from chunk tree.
| (AKA, super num devs is already incorrect)
|
|- cur_devices->num_devices--;
|- cur_devices->total_devices--;
|- btrfs_set_super_num_devices()
All those operations are not in transaction X, thus it will
only be written back to disk in next transaction.
So after the transaction X in btrfs_rm_dev_item() committed, but before
transaction X+1 (which can be minutes away), a power loss happen, then
we got the super num mismatch.
This has been fixed by commit f2b90921a980 ("btrfs: remove device item
and update super block in the same transaction").
[FIX]
Make the super_num_devices check less strict, converting it from a hard
error to a warning, and reset the value to a correct one for the current
or next transaction commit.
As the number of device items is the critical information where the
super block num_devices is only a cached value (and also useful for
cross checking), it's safe to automatically update it. Other device
related problems like missing device are handled after that and may
require other means to resolve, like degraded mount. With this fix,
potentially affected filesystems won't fail mount and require the manual
repair by btrfs check.
[BUG]
If we hit an error from submit_extent_page() inside
__extent_writepage_io(), we could still return 0 to the caller, and
even trigger the warning in btrfs_page_assert_not_dirty().
[CAUSE]
In __extent_writepage_io(), if we hit an error from
submit_extent_page(), we will just clean up the range and continue.
This is completely fine for regular PAGE_SIZE == sectorsize, as we can
only hit one sector in one page, thus after the error we're ensured to
exit and @ret will be saved.
But for subpage case, we may have other dirty subpage range in the page,
and in the next loop, we may succeeded submitting the next range.
In that case, @ret will be overwritten, and we return 0 to the caller,
while we have hit some error.
[FIX]
Introduce @has_error and @saved_ret to record the first error we hit, so
we will never forget what error we hit.
The following error message lack the "0x" obviously:
cannot mount because of unsupported optional features (4000)
Add the prefix to make it less confusing. This can happen on older
kernels that try to mount a filesystem with newer features so it makes
sense to backport to older trees.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of PTRACE_KILL is buggy and has been for
many years as it assumes it's target has stopped in ptrace_stop. At a
quick skim it looks like this assumption has existed since ptrace
support was added in linux v1.0.
While PTRACE_KILL has been deprecated we can not remove it as
a quick search with google code search reveals many existing
programs calling it.
When the ptracee is not stopped at ptrace_stop some fields would be
set that are ignored except in ptrace_stop. Making the userspace
visible behavior of PTRACE_KILL a noop in those case.
As the usual rules are not obeyed it is not clear what the
consequences are of calling PTRACE_KILL on a running process.
Presumably userspace does not do this as it achieves nothing.
Replace the implementation of PTRACE_KILL with a simple
send_sig_info(SIGKILL) followed by a return 0. This changes the
observable user space behavior only in that PTRACE_KILL on a process
not stopped in ptrace_stop will also kill it. As that has always
been the intent of the code this seems like a reasonable change.
Cc: stable@vger.kernel.org Reported-by: Al Viro <viro@zeniv.linux.org.uk> Suggested-by: Al Viro <viro@zeniv.linux.org.uk> Tested-by: Kees Cook <keescook@chromium.org> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Link: https://lkml.kernel.org/r/20220505182645.497868-7-ebiederm@xmission.com Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xtensa is the last user of the PT_SINGLESTEP flag. Changing tsk->ptrace in
user_enable_single_step and user_disable_single_step without locking could
potentiallly cause problems.
So use a thread info flag instead of a flag in tsk->ptrace. Use TIF_SINGLESTEP
that xtensa already had defined but unused.
Remove the definitions of PT_SINGLESTEP and PT_BLOCKSTEP as they have no more users.
User mode linux is the last user of the PT_DTRACE flag. Using the flag to indicate
single stepping is a little confusing and worse changing tsk->ptrace without locking
could potentionally cause problems.
So use a thread info flag with a better name instead of flag in tsk->ptrace.
Remove the definition PT_DTRACE as uml is the last user.
When the system runs out of enclave memory, SGX can reclaim EPC pages
by swapping to normal RAM. These backing pages are allocated via a
per-enclave shared memory area. Since SGX allows unlimited over
commit on EPC memory, the reclaimer thread can allocate a large
number of backing RAM pages in response to EPC memory pressure.
When the shared memory backing RAM allocation occurs during
the reclaimer thread context, the shared memory is charged to
the root memory control group, and the shmem usage of the enclave
is not properly accounted for, making cgroups ineffective at
limiting the amount of RAM an enclave can consume.
For example, when using a cgroup to launch a set of test
enclaves, the kernel does not properly account for 50% - 75% of
shmem page allocations on average. In the worst case, when
nearly all allocations occur during the reclaimer thread, the
kernel accounts less than a percent of the amount of shmem used
by the enclave's cgroup to the correct cgroup.
SGX stores a list of mm_structs that are associated with
an enclave. Pick one of them during reclaim and charge that
mm's memcg with the shmem allocation. The one that gets picked
is arbitrary, but this list almost always only has one mm. The
cases where there is more than one mm with different memcg's
are not worth considering.
Create a new function - sgx_encl_alloc_backing(). This function
is used whenever a new backing storage page needs to be
allocated. Previously the same function was used for page
allocation as well as retrieving a previously allocated page.
Prior to backing page allocation, if there is a mm_struct associated
with the enclave that is requesting the allocation, it is set
as the active memory control group.
[ dhansen: - fix merge conflict with ELDU fixes
- check against actual ksgxd_tsk, not ->mm ]
Cc: stable@vger.kernel.org Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <roman.gushchin@linux.dev> Link: https://lkml.kernel.org/r/20220520174248.4918-1-kristen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In crash_prepare_elf64_headers(), a buffer is allocated via vmalloc() to
store elf headers. While it's not freed back to system correctly when
kdump kernel is reloaded or unloaded. Then memory leak is caused. Fix it
by introducing x86 specific function arch_kimage_file_post_load_cleanup(),
and freeing the buffer there.
And also remove the incorrect elf header buffer freeing code. Before
calling arch specific kexec_file loading function, the image instance has
been initialized. So 'image->elf_headers' must be NULL. It doesn't make
sense to free the elf header buffer in the place.
Three different people have reported three bugs about the memory leak on
x86_64 inside Redhat.
Link: https://lkml.kernel.org/r/20220223113225.63106-2-bhe@redhat.com Signed-off-by: Baoquan He <bhe@redhat.com> Acked-by: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log