According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Add KRYO4XX gold/big cores to the list of CPUs that need the
repeat TLBI workaround. Apply this to the affected
KRYO4XX cores (rcpe to rfpe).
The variant and revision bits are implementation defined and are
different from the their Cortex CPU counterparts on which they are
based on, i.e., (r0p0 to r3p0) is equivalent to (rcpe to rfpe).
Bounds check hw_head index provided by NIC to verify it lies
within the TX buffer ring.
Reported-by: Aashay Shringarpure <aashay@google.com> Reported-by: Yi Chou <yich@google.com> Reported-by: Shervin Oloumi <enlightened@google.com> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enforce that the CPU can not get stuck in an infinite loop.
Reported-by: Aashay Shringarpure <aashay@google.com> Reported-by: Yi Chou <yich@google.com> Reported-by: Shervin Oloumi <enlightened@google.com> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't defer handling the err case outside the loop. That's pointless.
And since is_rsc_complete is only used inside this loop, declare
it inside the loop to reduce it's scope.
Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In aq_ring_rx_clean(), if buff->is_eop is not set AND
buff->len < AQ_CFG_RX_HDR_SIZE, then hdr_len remains equal to
buff->len and skb_add_rx_frag(xxx, *0*, ...) is not called.
The loop following this code starts calling skb_add_rx_frag() starting
with i=1 and thus frag[0] is never initialized. Since i is initialized
to zero at the top of the primary loop, we can just reference and
post-increment i instead of hardcoding the 0 when calling
skb_add_rx_frag() the first time.
Reported-by: Aashay Shringarpure <aashay@google.com> Reported-by: Yi Chou <yich@google.com> Reported-by: Shervin Oloumi <enlightened@google.com> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When clatd starts with ebpf offloaing, and NETIF_F_GRO_FRAGLIST is enable,
several skbs are gathered in skb_shinfo(skb)->frag_list. The first skb's
ipv6 header will be changed to ipv4 after bpf_skb_proto_6_to_4,
network_header\transport_header\mac_header have been updated as ipv4 acts,
but other skbs in frag_list didnot update anything, just ipv6 packets.
udp_queue_rcv_skb will call skb_segment_list to traverse other skbs in
frag_list and make sure right udp payload is delivered to user space.
Unfortunately, other skbs in frag_list who are still ipv6 packets are
updated like the first skb and will have wrong transport header length.
e.g.before bpf_skb_proto_6_to_4,the first skb and other skbs in frag_list
has the same network_header(24)& transport_header(64), after
bpf_skb_proto_6_to_4, ipv6 protocol has been changed to ipv4, the first
skb's network_header is 44,transport_header is 64, other skbs in frag_list
didnot change.After skb_segment_list, the other skbs in frag_list has
different network_header(24) and transport_header(44), so there will be 20
bytes different from original,that is difference between ipv6 header and
ipv4 header. Just change transport_header to be the same with original.
Actually, there are two solutions to fix it, one is traversing all skbs
and changing every skb header in bpf_skb_proto_6_to_4, the other is
modifying frag_list skb's header in skb_segment_list. Considering
efficiency, adopt the second one--- when the first skb and other skbs in
frag_list has different network_header length, restore them to make sure
right udp payload is delivered to user space.
Signed-off-by: Lina Wang <lina.wang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most fbdev drivers have issues with the fb_info lifetime, because call to
framebuffer_release() from their driver's .remove callback, rather than
doing from fbops.fb_destroy callback.
Doing that will destroy the fb_info too early, while references to it may
still exist, leading to a use-after-free error.
To prevent this, check the fb_info reference counter when attempting to
kfree the data structure in framebuffer_release(). That will leak it but
at least will prevent the mentioned error.
This reverts commit df26cbb3540940e57fc2b6430e45621680a1db2b. That commit
attempted to fix a NULL pointer dereference, caused by the struct fb_info
associated with a framebuffer device to not longer be valid when the file
descriptor was closed.
The issue was exposed by commit 889ae79e9a8c ("fbdev: Hot-unplug firmware
fb devices on forced removal"), which added a new path that goes through
the struct device removal instead of directly unregistering the fb.
Most fbdev drivers have issues with the fb_info lifetime, because call to
framebuffer_release() from their driver's .remove callback, rather than
doing from fbops.fb_destroy callback. This meant that due to this switch,
the fb_info was now destroyed too early, while references still existed,
while before it was simply leaked.
The patch we're reverting here reinstated that leak, hence "fixed" the
regression. But the proper solution is to fix the drivers to not release
the fb_info too soon.
The 'ping' utility is able to manage two kind of sockets (raw or icmp),
depending on the sysctl ping_group_range. By default, ping_group_range is
set to '1 0', which forces ping to use an ip raw socket.
Let's replay the ping tests by allowing 'ping' to use the ip icmp socket.
After the previous patch, ipv4 tests results are the same with both kinds
of socket. For ipv6, there are a lot a new failures (the previous patch
fixes only two cases).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the QoS ack policy was set to non explicit / psmp ack, frames are treated
as not being part of a BA session, which causes extra latency on reordering.
Fix this by only bypassing reordering for packets with no-ack policy
The handling of the ALUA transitioning state is currently broken. When a
target goes into this state, it is expected that the target is allowed to
stay in this state for the implicit transition timeout without a path
failure. The handler has this logic, but it gets skipped currently.
When the target transitions, there is in-flight I/O from the initiator. The
first of these responses from the target will be a unit attention letting
the initiator know that the ALUA state has changed. The remaining
in-flight I/Os, before the initiator finds out that the portal state has
changed, will return not ready, ALUA state is transitioning. The portal
state will change to SCSI_ACCESS_STATE_TRANSITIONING. This will lead to all
new I/O immediately failing the path unexpectedly. The path failure happens
in less than a second instead of the expected successes until the
transition timer is exceeded.
Allow I/Os to continue while the path is in the ALUA transitioning
state. The handler already takes care of a target that stays in the
transitioning state for too long by changing the state to ALUA state
standby once the transition timeout is exceeded at which point the path
will fail.
Link: https://lore.kernel.org/r/CAHZQxy+4sTPz9+pY3=7VJH+CLUJsDct81KtnR2be8ycN5mhqTg@mail.gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Acked-by: Krishna Kant <krishna.kant@purestorage.com> Acked-by: Seamus Connor <sconnor@purestorage.com> Signed-off-by: Brian Bunker <brian@purestorage.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
# make DEBUG=y bench/numa.o
...
bench/numa.c: In function ‘__bench_numa’:
bench/numa.c:1749:81: error: ‘%d’ directive output may be truncated
writing between 1 and 11 bytes into a region of size between
10 and 20 [-Werror=format-truncation=]
1749 | snprintf(tname, sizeof(tname), "process%d:thread%d", p, t);
^~
...
bench/numa.c:1749:64: note: directive argument in the range
[-2147483647, 2147483646]
...
#
The maximum length of the %d replacement is 11 characters because of the
negative sign. Therefore extend the array by two more characters.
Output after:
# make DEBUG=y bench/numa.o > /dev/null 2>&1; ll bench/numa.o
-rw-r--r-- 1 root root 418320 May 19 09:11 bench/numa.o
#
Fixes: 2ec394d998b083ca ("perf bench numa: Avoid possible truncation when using snprintf()") Suggested-by: Namhyung Kim <namhyung@gmail.com> Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Sumanth Korikkar <sumanthk@linux.ibm.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Link: https://lore.kernel.org/r/20220520081158.2990006-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The X86 specific arch__intr_reg_mask() is to check whether the kernel
and hardware can collect XMM registers. But it doesn't work on some
hybrid platform.
Without the patch on ADL-N:
$ perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10
R11 R12 R13 R14 R15
The config of the test event doesn't contain the PMU information. The
kernel may fail to initialize it on the correct hybrid PMU and return
the wrong non-supported information.
Add the PMU information into the config for the hybrid platform. The
same register set is supported among different hybrid PMUs. Checking
the first available one is good enough.
With the patch on ADL-N:
$ perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10
R11 R12 R13 R14 R15 XMM0 XMM1 XMM2 XMM3 XMM4 XMM5 XMM6 XMM7 XMM8 XMM9
XMM10 XMM11 XMM12 XMM13 XMM14 XMM15
Fixes: 415197a3373aa2a6 ("perf regs x86: Add X86 specific arch__intr_reg_mask()") Reported-by: Ammy Yi <ammy.yi@intel.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Acked-by: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Xing Zhengjun <zhengjun.xing@linux.intel.com> Link: https://lore.kernel.org/r/20220518145125.1494156-1-kan.liang@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.
Avi Kivity reported a problem where the __weak
btf__load_from_kernel_by_id() in tools/perf/util/bpf-event.c was being
used and it called btf__get_from_id() in tools/lib/bpf/btf.c that in
turn called back to btf__load_from_kernel_by_id(), resulting in an
endless loop.
Fix this by adding a feature test to check if
btf__load_from_kernel_by_id() is available when building perf with
LIBBPF_DYNAMIC=1, and if not then provide the fallback to the old
btf__get_from_id(), that doesn't call back to btf__load_from_kernel_by_id()
since at that time it didn't exist at all.
Tested on Fedora 35 where we have libbpf-devel 0.4.0 with LIBBPF_DYNAMIC
where we don't have btf__load_from_kernel_by_id() and thus its feature
test fail, not defining HAVE_LIBBPF_BTF__LOAD_FROM_KERNEL_BY_ID:
$ cat /tmp/build/perf-urgent/feature/test-libbpf-btf__load_from_kernel_by_id.make.output
test-libbpf-btf__load_from_kernel_by_id.c: In function ‘main’:
test-libbpf-btf__load_from_kernel_by_id.c:6:16: error: implicit declaration of function ‘btf__load_from_kernel_by_id’ [-Werror=implicit-function-declaration]
6 | return btf__load_from_kernel_by_id(20151128, NULL);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
$
$ nm /tmp/build/perf-urgent/perf | grep btf__load_from_kernel_by_id 00000000005ba180 T btf__load_from_kernel_by_id
$
Fix referencing sense data when it is invalid. When the length of the data
segment is 0, there is no valid information in the rsp field, so
ufshpb_rsp_upiu() is returned without additional operation.
Link: https://lore.kernel.org/r/252651381.41652940482659.JavaMail.epsvc@epcpadp4 Fixes: ca2f60808241 ("scsi: ufs: ufshpb: L2P map management for HPB read") Acked-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Daejun Park <daejun7.park@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: d7ca5bc918c9 ("bridge: switchdev: Use an helper to clear forward mark") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes sporadic IPv6 packet loss when flow offloading is enabled.
IPv6 route GC and flowtable GC are not synchronized.
When dst_cache becomes stale and a packet passes through the flow before
the flowtable GC teardowns it, the packet can be dropped.
So, it is necessary to check dst every time in packet path.
1. ct gc may race to undo the timeout adjustment of the packet path, leaving
the conntrack entry in place with the internal offload timeout (one day).
2. ct gc removes the ct because the IPS_OFFLOAD_BIT is not set and the CLOSE
timeout is reached before the flow offload del.
3. tcp ct is always set to ESTABLISHED with a very long timeout
in flow offload teardown/delete even though the state might be already
CLOSED. Also as a remark we cannot assume that the FIN or RST packet
is hitting flow table teardown as the packet might get bumped to the
slow path in nftables.
This patch resets IPS_OFFLOAD_BIT from flow_offload_teardown(), so
conntrack handles the tcp rst/fin packet which triggers the CLOSE/FIN
state transition.
Moreover, teturn the connection's ownership to conntrack upon teardown
by clearing the offload flag and fixing the established timeout value.
The flow table GC thread will asynchonrnously free the flow table and
hardware offload entries.
Before this patch, the IPS_OFFLOAD_BIT remained set for expired flows on
which is also misleading since the flow is back to classic conntrack
path.
If nf_ct_delete() removes the entry from the conntrack table, then it
calls nf_ct_put() which decrements the refcnt. This is not a problem
because the flowtable holds a reference to the conntrack object from
flow_offload_alloc() path which is released via flow_offload_free().
This patch also updates nft_flow_offload to skip packets in SYN_RECV
state. Since we might miss or bump packets to slow path, we do not know
what will happen there while we are still in SYN_RECV, this patch
postpones offload up to the next packet which also aligns to the
existing behaviour in tc-ct.
flow_offload_teardown() does not reset the existing tcp state from
flow_offload_fixup_tcp() to ESTABLISHED anymore, packets bump to slow
path might have already update the state to CLOSE/FIN.
Joint work with Oz and Sven.
Fixes: af46bd490751 ("netfilter: nf_flow_table: teardown flow timeout race") Signed-off-by: Oz Shlomo <ozsh@nvidia.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: 4db53b7f37a2 ("igb: When GbE link up, wait for Remote receiver status condition") Signed-off-by: Kevin Mitchell <kevmitch@arista.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MPTCP code typecasts the checksum value to u16 and
then converts it to big endian while storing the value into
the MPTCP option.
As a result, the wire encoding for little endian host is
wrong, and that causes interoperabilty interoperability
issues with other implementation or host with different endianness.
Address the issue writing in the packet the unmodified __sum16 value.
MPTCP checksum is disabled by default, interoperating with systems
with bad mptcp-level csum encoding should cause fallback to TCP.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/275 Fixes: 625e985bd890 ("mptcp: send out checksum for DSS") Fixes: 0155a35ad263 ("mptcp: receive checksum for DSS") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In Thumb2, 'b . + 4' produces a branch instruction that uses a narrow
encoding, and so it does not jump to the following instruction as
expected. So use W(b) instead.
Fixes: 07cd9e9e75d8 ("ARM: fix Thumb2 regression with Spectre BHB") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Spectre-BHB mitigations were inadvertently left disabled for
Cortex-A15, due to the fact that cpu_v7_bugs_init() is not called in
that case. So fix that.
Fixes: 404a7a266c1a ("ARM: Spectre-BHB workaround") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If skb_clone() returns null pointer, pfkey_broadcast() will
return error.
Therefore, it should be better to check the return value of
pfkey_broadcast() and return error if fails.
LRO is incompatible and mutually exclusive with XDP. However, the needed
checks are only made when enabling XDP. If LRO is enabled when XDP is
already active, the command will succeed, and XDP will be skipped in the
data path, although still enabled.
This commit fixes the bug by checking the XDP status in
mlx5e_fix_features and disabling LRO if XDP is enabled.
In order to support multiple destination FTEs with SW steering
FW table is created with single FTE with multiple actions and
SW steering rule forward to it. When creating this table, flow
source isn't set according to the original FTE.
Fix this by passing the original FTE flow source to the created
FW table.
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: 65e4f1d1f7d2 ("nfc: st-nci: Rename st21nfcb to st-nci") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
clk_generated_best_diff() helps in finding the parent and the divisor to
compute a rate closest to the required one. However, it doesn't take into
account the request's range for the new rate. Make sure the new rate
is within the required range.
Fixes: 715dcb4062ed ("clk: at91: clk-generated: create function to find best_diff") Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220413071318.244912-1-codrin.ciubotariu@microchip.com Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adaptive-rx and Adaptive-tx are interrupt moderation settings
that can be enabled/disabled using ethtool:
ethtool -C ethX adaptive-rx on/off adaptive-tx on/off
Unfortunately those settings are getting cleared after
changing number of queues, or in ethtool world 'channels':
ethtool -L ethX rx 1 tx 1
Clearing was happening due to introduction of bit fields
in ice_ring_container struct. This way only itr_setting
bits were rebuilt during ice_vsi_rebuild_set_coalesce().
Introduce an anonymous struct of bitfields and create a
union to refer to them as a single variable.
This way variable can be easily saved and restored.
Fixes: 7756f2da2ae9 ("ice: Restore interrupt throttle settings after VSI rebuild") Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently ice_container_type is scoped only for ice_ethtool.c. Next
commit that will split the ice_ring struct onto Rx/Tx specific ring
structs is going to also modify the type of linked list of rings that is
within ice_ring_container. Therefore, the functions that are taking the
ice_ring_container as an input argument will need to be aware of a ring
type that will be looked up.
Embed ice_container_type within ice_ring_container and initialize it
properly when allocating the q_vectors.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 26c816c61a1e3 ("ice: ignore dropped packets during init") Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not allow to write timestamps on RX rings if PF is being configured.
When PF is being configured RX rings can be freed or rebuilt. If at the
same time timestamps are updated, the kernel will crash by dereferencing
null RX ring pointer.
In vmxnet3_rq_create(), when dma_alloc_coherent() fails,
vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then
vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all()
-> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls
vmxnet3_force_close() -> dev_close() in error handling code. And the driver
calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all()
-> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(),
rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing
a NULL pointer dereference.
To fix this possible bug, an if statement is added to check whether
rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so.
The error log in our fault-injection testing is shown as follows:
In vmxnet3_rq_alloc_rx_buf(), when dma_map_single() fails, rbi->skb is
freed immediately. Similarly, in another branch, when dma_map_page() fails,
rbi->page is also freed. In the two cases, vmxnet3_rq_alloc_rx_buf()
returns an error to its callers vmxnet3_rq_init() -> vmxnet3_rq_init_all()
-> vmxnet3_activate_dev(). Then vmxnet3_activate_dev() calls
vmxnet3_rq_cleanup_all() in error handling code, and rbi->skb or rbi->page
are freed again in vmxnet3_rq_cleanup_all(), causing use-after-free bugs.
To fix these possible bugs, rbi->skb and rbi->page should be cleared after
they are freed.
The error log in our fault-injection testing is shown as follows:
This commit broke support for setting interrupt affinity. It looks like
that it is related to the chained IRQ handler. Revert this commit until
issue with setting interrupt affinity is fixed.
When running a combination of PPPoE on top of a VLAN, we need to set
info->outdev to the PPPoE device, otherwise PPPoE encap is skipped
during software offload.
Fixes: de59ef53d107 ("netfilter: flowtable: add pppoe support") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When calling dev_fill_forward_path on a pppoe device, the provided destination
address is invalid. In order for the bridge fdb lookup to succeed, the pppoe
code needs to update ctx->daddr to the correct value.
Fix this by storing the address inside struct net_device_path_ctx
Fixes: 9cb6adb5c2e1 ("net: ppp: resolve forwarding path for bridge pppoe devices") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dst entry does not contain a valid hardware address, so skip the lookup
in order to avoid running into errors here.
The proper hardware address is filled in from nft_dev_path_info
Fixes: de59ef53d107 ("netfilter: flowtable: add pppoe support") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a flow cannot be offloaded, the code currently repeatedly tries again as
quickly as possible, which can significantly increase system load.
Fix this by limiting flow timeout update and hardware offload retry to once
per second.
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com Fixes: b91a0653a96f ("net/sched: act_pedit: really ensure the skb is writable") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In IPv4 setting the "disable_policy" flag on a device means no policy
should be enforced for traffic originating from the device. This was
implemented by seting the DST_NOPOLICY flag in the dst based on the
originating device.
However, dsts are cached in nexthops regardless of the originating
devices, in which case, the DST_NOPOLICY flag value may be incorrect.
dst entries for traffic arriving from eth0 would have DST_NOPOLICY
and would be cached and therefore can be reused by traffic originating
from ipsec0, skipping policy check.
Fix by setting a IPSKB_NOPOLICY flag in IPCB and observing it instead
of the DST in IN/FWD IPv4 policy checks.
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
Each time we are notified that some number of transactions on an RX
channel has completed, we record the number of bytes that have been
transferred since the previous notification. We also track the
number of transactions completed, but that is not currently being
calculated correctly; we're currently counting the number of such
notifications, but each notification can represent many transaction
completions. Fix this.
Fixes: 31210ccab1a3d ("soc: qcom: ipa: the generic software interface") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_PM is not enabled, alc_shutup() is not needed,
so move it inside the #ifdef CONFIG_PM guard.
Also drop some contiguous #endif / #ifdef CONFIG_PM for simplicity.
Fixes this build warning:
sound/pci/hda/patch_realtek.c:886:20: warning: unused function 'alc_shutup'
Fixes: 69414e690665 ("ALSA: hda - Use generic parser codes for Realtek driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20220430193318.29024-1-rdunlap@infradead.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com> Link: https://lore.kernel.org/r/20211117035106.321454-3-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the ADC nodes to the AST2600 devicetree. Enable ADC1 for Rainier and
Everest systems and add an iio-hwmon node for the 7th channel to report
the battery voltage.
Tested on Rainier:
~# cat /sys/class/hwmon/hwmon11/in1_input
1347
FWSPIDQ2 and FWSPIDQ3 are not part of FWSPI18 interface so remove
FWQSPID group in pinctrl. These pins must be used with the FWSPI
pins that are dedicated for boot SPI interface which provides
same 3.3v logic level.
Fixes: 300fc7e7af61 ("pinctrl: aspeed: Add AST2600 pinmux support") Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20220329173932.2588289-3-quic_jaehyoo@quicinc.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
FWSPIDQ2 and FWSPIDQ3 are not part of FWSPI18 interface so remove
FWQSPID group in pinctrl dtsi. These pins must be used with the
FWSPI pins that are dedicated for boot SPI interface which provides
same 3.3v logic level.
Fixes: 5907415704cd ("ARM: dts: aspeed: Fix AST2600 quad spi group") Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20220329173932.2588289-2-quic_jaehyoo@quicinc.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dmabuf file uses get_next_ino()(through dma_buf_getfile() ->
alloc_anon_inode()) to get an inode number and uses the same as a
directory name under /sys/kernel/dmabuf/buffers/<ino>. This directory is
used to collect the dmabuf stats and it is created through
dma_buf_stats_setup(). At current, failure to create this directory
entry can make the dma_buf_export() to fail.
Now, as the get_next_ino() can definitely give a repetitive inode no
causing the directory entry creation to fail with -EEXIST. This is a
problem on the systems where dmabuf stats functionality is enabled on
the production builds can make the dma_buf_export(), though the dmabuf
memory is allocated successfully, to fail just because it couldn't
create stats entry.
This issue we are able to see on the snapdragon system within 13 days
where there already exists a directory with inode no "122602" so
dma_buf_stats_setup() failed with -EEXIST as it is trying to create
the same directory entry.
To make the dentry name as unique, use the dmabuf fs specific inode
which is based on the simple atomic variable increment. There is tmpfs
subsystem too which relies on its own inode generation rather than
relying on the get_next_ino() for the same reason of avoiding the
duplicate inodes[1].
Bspec has added some steps that check forDMC MMIO range before
programming them
v2: Fix for CI
v3: move register defines to .h (Anusha)
- Check MMIO restrictions per pipe
- Add MMIO restricton for v1 dmc header as well (Lucas)
v4: s/_PICK/_PICK_EVEN and use it only for Pipe DMC scenario.
- clean up sanity check logic.(Lucas)
- Add MMIO range for RKL as well.(Anusha)
v5: Use DISPLAY_VER instead of per platform check (Lucas)
BSpec: 49193
Cc: stable@vger.kernel.org Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220511000847.1068302-1-anusha.srivatsa@intel.com
(cherry picked from commit 1bfbad113b2d95eaa9844dd205c3dfcfc8b59aca) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An A+A configuration on ASUS ROG Strix G513QY proves that the ASIC
reset for handling aborted suspend can't work with s2idle.
This functionality was introduced in commit b890ad00836d61 ("drm/amdgpu:
always reset the asic in suspend (v2)"). A few other commits have
gone on top of the ASIC reset, but this still doesn't work on the A+A
configuration in s2idle.
Avoid doing the reset on dGPUs specifically when using s2idle.
Fixes: b890ad00836d61 ("drm/amdgpu: always reset the asic in suspend (v2)") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2008 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
request_reinit() is not only ugly as the comment rightfully suggests,
but also unsafe. Even though it is called with osdc->lock held for
write in all cases, resetting the OSD request refcount can still race
with handle_reply() and result in use-after-free. Taking linger ping
as an example:
# req->r_kref == 2 because handle_reply still holds its ref
down_write(&osdc->lock)
send_linger_ping(lreq)
req = lreq->ping_req # same req
# cancel_linger_request is NOT
# called - handle_reply already
# unregistered
request_reinit(req)
WARN_ON(req->r_kref != 1) # fires
request_init(req)
kref_init(req->r_kref)
# req->r_kref == 1 after kref_init
ceph_osdc_put_request(req)
kref_put(req->r_kref)
# req->r_kref == 0 after kref_put, req is freed
<further req initialization/use> !!!
This happens because send_linger_ping() always (re)uses the same OSD
request for watch ping requests, relying on cancel_linger_request() to
unregister it from the OSD client and rip its messages out from the
messenger. send_linger() does the same for watch/notify registration
and watch reconnect requests. Unfortunately cancel_request() doesn't
guarantee that after it returns the OSD client would be completely done
with the OSD request -- a ref could still be held and the callback (if
specified) could still be invoked too.
The original motivation for request_reinit() was inability to deal with
allocation failures in send_linger() and send_linger_ping(). Switching
to using osdc->req_mempool (currently only used by CephFS) respects that
and allows us to get rid of request_reinit().
Cc: stable@vger.kernel.org Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Xiubo Li <xiubli@redhat.com> Acked-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit referenced in the Fixes tag removed the 'break' from the else
branch in qcom_rng_read(), causing an infinite loop whenever 'max' is
not a multiple of WORD_SZ. This can be reproduced e.g. by running:
kcapi-rng -b 67 >/dev/null
There are many ways to fix this without adding back the 'break', but
they all seem more awkward than simply adding it back, so do just that.
Tested on a machine with Qualcomm Amberwing processor.
Fixes: 671c0d09c1e2 ("crypto: qcom-rng - ensure buffer for generate is completely filled") Cc: stable@vger.kernel.org Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Reviewed-by: Brian Masney <bmasney@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As an optimisation, only pages mapped with PROT_MTE in user space have
the MTE tags zeroed. This is done lazily at the set_pte_at() time via
mte_sync_tags(). However, this function is missing a barrier and another
CPU may see the PTE updated before the zeroed tags are visible. Add an
smp_wmb() barrier if the mapping is Normal Tagged.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Fixes: 1cf0da792be1 ("arm64: mte: Clear the tags when a page is mapped in user-space with PROT_MTE") Cc: <stable@vger.kernel.org> # 5.10.x Reported-by: Vladimir Murzin <vladimir.murzin@arm.com> Cc: Will Deacon <will@kernel.org> Reviewed-by: Steven Price <steven.price@arm.com> Tested-by: Vladimir Murzin <vladimir.murzin@arm.com> Link: https://lore.kernel.org/r/20220517093532.127095-1-catalin.marinas@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During hotplug, the stolen time data structure is unmapped and memset.
There is a possibility of the timer IRQ being triggered before memset
and stolen time is getting updated as part of this timer IRQ handler. This
causes the below crash in timer handler -
When zapping obsolete pages, update the running count of zapped pages
regardless of whether or not the list has become unstable due to zapping
a shadow page with its own child shadow pages. If the VM is backed by
mostly 4kb pages, KVM can zap an absurd number of SPTEs without bumping
the batch count and thus without yielding. In the worst case scenario,
this can cause a soft lokcup.
Commit 6fdb06f1ab99 ("can: m_can: pci: use custom bit timings for
Elkhart Lake") broke the test case using bitrate switching.
| ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on
| ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on
| candump can0 &
| cangen can1 -I 0x800 -L 64 -e -fb \
| -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v
Above commit does everything correctly according to the datasheet.
However datasheet wasn't correct.
I got confirmation from hardware engineers that the actual CAN
hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0.
Datasheet was mirroring values from an another specification which was
based on earlier M_CAN version leading to wrong bit timings.
Therefore revert the commit and switch back to common bit timings.
Fixes: d9621f6091ad ("can: m_can: pci: use custom bit timings for Elkhart Lake") Link: https://lore.kernel.org/all/20220512124144.536850-1-jarkko.nikula@linux.intel.com Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reported-by: Chee Hou Ong <chee.houx.ong@intel.com> Reported-by: Aman Kumar <aman.kumar@intel.com> Reported-by: Pallavi Kumari <kumari.pallavi@intel.com> Cc: <stable@vger.kernel.org> # v5.16+ Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a Root Port on Elo i2 is put into D3cold and then back into D0, the
downstream device becomes permanently inaccessible, so add a bridge D3 DMI
quirk for that system.
This was exposed by 67f8e78c0297 ("PCI: Use pci_update_current_state() in
pci_enable_device_flags()"), but before that commit the Root Port in
question had never been put into D3cold for real due to a mismatch between
its power state retrieved from the PCI_PM_CTRL register (which was
accessible even though the platform firmware indicated that the port was in
D3cold) and the state of an ACPI power resource involved in its power
management.
Descriptor table is a shared resource; two fget() on the same descriptor
may return different struct file references. get_tap_ptr_ring() is
called after we'd found (and pinned) the socket we'll be using and it
tries to find the private tun/tap data structures associated with it.
Redoing the lookup by the same file descriptor we'd used to get the
socket is racy - we need to same struct file.
Thanks to Jason for spotting a braino in the original variant of patch -
I'd missed the use of fd == -1 for disabling backend, and in that case
we can end up with sock == NULL and sock != oldsock.
Cc: stable@kernel.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code attempts to free the 'new' pointer using kmem_cache_free(),
which is wrong because this function isn't responsible of freeing it.
Instead, the function should free new->htable and clear the contents of
*new (to prevent double-free).
Cc: stable@vger.kernel.org Fixes: af4864c1b2c0 ("selinux: refactor changing booleans") Reported-by: Wander Lairson Costa <wander@redhat.com> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Norbert reported that it's possible to race sys_perf_event_open() such
that the looser ends up in another context from the group leader,
triggering many WARNs.
The move_group case checks for races against itself, but the
!move_group case doesn't, seemingly relying on the previous
group_leader->ctx == ctx check. However, that check is racy due to not
holding any locks at that time.
Therefore, re-check the result after acquiring locks and bailing
if they no longer match.
Additionally, clarify the not_move_group case from the
move_group-vs-move_group race.
The antient ISA wavefront driver reads its sample patch data (uploaded
over an ioctl) via __get_user() with no good reason; likely just for
some performance optimizations in the past. Let's change this to the
standard get_user() and the error check for handling the fault case
properly.
At cleaning up and moving the device rename from the quirk table to
its own table, we removed the entry for Rane SL-1 as we thought it's
only for renaming. It turned out, however, that the quirk is required
for matching with the device that declares itself as no standard
audio but only as vendor-specific.
Restore the quirk entry for Rane SL-1 to fix the regression.
During disk space reclamation, nilfs2 still emits the following lockdep
warning due to page/folio operations on shadowed page caches that nilfs2
uses to get a snapshot of DAT file in memory:
The first two are to resolve the lockdep warning issue, and the last one
is the accompanying cleanup and low priority.
Based on your comment, this series solves the issue by separating inode
object as needed. Since I was worried about the impact of the object
composition changes, I tested the series carefully not to cause
regressions especially for delicate functions such like disk space
reclamation and snapshots.
This patch (of 3):
If CONFIG_LOCKDEP is enabled, nilfs2 hits lockdep warnings at
inode_to_wb() during page/folio operations for btree nodes:
This is because nilfs2 uses two page caches for each inode and
inode->i_mapping never points to one of them, the btree node cache.
This causes inode_to_wb(inode) to refer to a different page cache than
the caller page/folio operations such like __folio_start_writeback(),
__folio_end_writeback(), or __folio_mark_dirty() acquired the lock.
This patch resolves the issue by allocating and using an additional
inode to hold the page cache of btree nodes. The inode is attached
one-to-one to the traditional nilfs2 inode if it requires a block
mapping with b-tree. This setup change is in memory only and does not
affect the disk format.
==================================================================
BUG: KASAN: stack-out-of-bounds in unwind_frame+0x508/0x870
Read of size 4 at addr c36bba90 by task cat/163
addr c36bba90 is located in stack of task cat/163 at offset 48 in frame:
stack_trace_save+0x0/0xb4
this frame has 1 object:
[32, 48) 'trace'
Memory state around the buggy address: c36bb980: f1 f1 f1 f1 00 04 f2 f2 00 00 f3 f3 00 00 00 00 c36bba00: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
>c36bba80: 00 00 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
^ c36bbb00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c36bbb80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
There is a same issue on x86 and has been resolved by the commit 81539dfdd4b7
("x86/mm, kasan: Silence KASAN warnings in get_wchan()").
The solution could be applied to arm architecture too.
Signed-off-by: Lin Yujun <linyujun809@huawei.com> Reported-by: He Ying <heying24@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Debugfs console_log uses devm memory (e.g. debug_info in
cros_ec_console_log_poll()). However, lifecycles of device and debugfs
are independent. An use-after-free issue is observed if userland
program operates the debugfs after the memory has been freed.
The call trace:
do_raw_spin_lock
_raw_spin_lock_irqsave
remove_wait_queue
ep_unregister_pollwait
ep_remove
do_epoll_ctl
A Python example to reproduce the issue:
... import select
... p = select.epoll()
... f = open('/sys/kernel/debug/cros_scp/console_log')
... p.register(f, select.POLLIN)
... p.poll(1)
[(4, 1)] # 4=fd, 1=select.POLLIN
kzalloc() is a memory allocation function which can return NULL when
some internal memory errors happen. So it is better to check the
return value of it to prevent potential wrong memory access or
memory leak.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
when get fiemap starting from MAX_LFS_FILESIZE, (maxbytes - *len) < start
will always true , then *len set zero. because of start offset is beyond
file size, for erofs filesystem it will always return iomap.length with
zero,iomap iterate will enter infinite loop. it is necessary cover this
corner case to avoid this situation.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Guo Xuenan <guoxuenan@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[djwong: fix some typos] Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting the century forward has been failing on AMD platforms.
There was a previous attempt at fixing this for family 0x17 as part of
commit ce9e9d843405 ("rtc: Fix the AltCentury value on AMD/Hygon
platform") but this was later reverted due to some problems reported
that appeared to stem from an FW bug on a family 0x17 desktop system.
The same comments mentioned in the previous commit continue to apply
to the newer platforms as well.
```
MC146818 driver use function mc146818_set_time() to set register
RTC_FREQ_SELECT(RTC_REG_A)'s bit4-bit6 field which means divider stage
reset value on Intel platform to 0x7.
While AMD/Hygon RTC_REG_A(0Ah)'s bit4 is defined as DV0 [Reference]:
DV0 = 0 selects Bank 0, DV0 = 1 selects Bank 1. Bit5-bit6 is defined
as reserved.
DV0 is set to 1, it will select Bank 1, which will disable AltCentury
register(0x32) access. As UEFI pass acpi_gbl_FADT.century 0x32
(AltCentury), the CMOS write will be failed on code:
CMOS_WRITE(century, acpi_gbl_FADT.century).
Correct RTC_REG_A bank select bit(DV0) to 0 on AMD/Hygon CPUs, it will
enable AltCentury(0x32) register writing and finally setup century as
expected.
```
However in closer examination the change previously submitted was also
modifying bits 5 & 6 which are declared reserved in the AMD documentation.
So instead modify just the DV0 bank selection bit.
Being cognizant that there was a failure reported before, split the code
change out to a static function that can also be used for exclusions if
any regressions such as Mikhail's pop up again.
nvme_mpath_init_identify() invoked from nvme_init_identify() fetches a
fresh ANA log from the ctrl. This is essential to have an up to date
path states for both existing namespaces and for those scan_work may
discover once the ctrl is up.
This happens in the following cases:
1) A new ctrl is being connected.
2) An existing ctrl is successfully reconnected.
3) An existing ctrl is being reset.
While in (1) ctrl->namespaces is empty, (2 & 3) may have namespaces, and
nvme_read_ana_log() may call nvme_update_ns_ana_state().
This result in a hang when the ANA state of an existing namespace changes
and makes the disk live: nvme_mpath_set_live() issues IO to the namespace
through the ctrl, which does NOT have IO queues yet.
See sample hang below.
Solution:
- nvme_update_ns_ana_state() to call set_live only if ctrl is live
- nvme_read_ana_log() call from nvme_mpath_init_identify()
therefore only fetches and parses the ANA log;
any erros in this process will fail the ctrl setup as appropriate;
- a separate function nvme_mpath_update()
is called in nvme_start_ctrl();
this parses the ANA log without fetching it.
At this point the ctrl is live,
therefore, disks can be set live normally.
Any attempt to flush kernel-global WQs has possibility of deadlock
so we should simply stop using them, instead introduce nvmet_wq
which is the generic nvmet workqueue for work elements that
don't explicitly require a dedicated workqueue (by the mere fact
that they are using the system_wq).
When irq number is negative(e.g., -EINVAL), the virtqueue
may be disabled or the virtqueues are sharing a device irq.
In such case, we should not setup irq offloading for a virtqueue.
Currently zpci_dev uses kref based reference counting but only accounts
for one original reference plus one reference from an added pci_dev to
its underlying zpci_dev. Counting just the original reference worked
until the pci_dev reference was added in commit 54d851ba2241 ("s390/pci:
fix use after free of zpci_dev") because once a zpci_dev goes away, i.e.
enters the reserved state, it would immediately get released. However
with the pci_dev reference this is no longer the case and the zpci_dev
may still appear in multiple availability events indicating that it was
reserved. This was solved by detecting when the zpci_dev is already on
its way out but still hanging around. This has however shown some light
on how unusual our zpci_dev reference counting is.
Improve upon this by modelling zpci_dev reference counting on pci_dev.
Analogous to pci_get_slot() increment the reference count in
get_zdev_by_fid(). Thus all users of get_zdev_by_fid() must drop the
reference once they are done with the zpci_dev.
Similar to pci_scan_single_device(), zpci_create_device() returns the
device with an initial count of 1 and the device added to the zpci_list
(analogous to the PCI bus' device_list). In turn users of
zpci_create_device() must only drop the reference once the device is
gone from the point of view of the zPCI subsystem, it might still be
referenced by the common PCI subsystem though.
There are many different types of translation exceptions but only a
translation-specification exception leads to a kernel panic since it
indicates corrupted page tables, which must never happen.
Improve the panic message so it is a bit more obvious what this is about.
The chacha_Nblock_xor_avx512vl() functions all have their own,
identical, .LdoneN label, however in one particular spot {2,4} jump to
the 8 version instead of their own. Resulting in:
arch/x86/crypto/chacha-x86_64.o: warning: objtool: chacha_2block_xor_avx512vl() falls through to next function chacha_8block_xor_avx512vl()
arch/x86/crypto/chacha-x86_64.o: warning: objtool: chacha_4block_xor_avx512vl() falls through to next function chacha_8block_xor_avx512vl()
Make each function consistently use its own done label.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log