Adrien reports that incorrect data is transmitted when a single
page straddles multiple records. We would transmit the same
data in all iterations of the loop.
Fix data corruption issue with SerDes connected PHYs operating at 1.25
Gbps speed where we could previously observe about 30% packet loss while
the bad packet counter was increasing.
As almost all boards with MediaTek MT7622 or MT7986 use either the MT7531
switch IC operating at 3.125Gbps SerDes rate or single-port PHYs using
rate-adaptation to 2500Base-X mode, this issue only got exposed now when
we started trying to use SFP modules operating with 1.25 Gbps with the
BananaPi R3 board.
The fix is to set bit 12 which disables the RX FIFO clear function when
setting up MAC MCR, MediaTek SDK did the same change stating:
"If without this patch, kernel might receive invalid packets that are
corrupted by GMAC."[1]
Currently link up can't be detected in forced mode if polling
isn't used. Only link up interrupt source we have is aneg
complete which isn't applicable in forced mode. Therefore we
have to use energy-on as link up indicator.
Fixes: 4ffe361110db ("net: phy: smsc: skip ENERGYON interrupt if disabled") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The last invocation of btf_datasec_resolve should invoke btf_var_resolve
by means of env_stack_push, instead it returns EINVAL. The reason is that
env_stack_push is never executed for the second VAR.
if (!env_type_is_resolve_sink(env, var_type) &&
!env_type_is_resolved(env, var_type_id)) {
env_stack_set_next_member(env, i + 1);
return env_stack_push(env, var_type, var_type_id);
}
env_type_is_resolve_sink() changes its behaviour based on resolve_mode.
For RESOLVE_PTR, we can simplify the if condition to the following:
Since we're dealing with a VAR the clause evaluates to false. This is
not sufficient to trigger the bug however. The log output and EINVAL
are only generated if btf_type_id_size() fails.
Most types are sized, so for example a VAR referring to an INT is not a
problem. The bug is only triggered if a VAR points at a modifier. Since
we skipped btf_var_resolve that modifier was also never resolved, which
means that btf_resolved_type_id returns 0 aka VOID for the modifier.
This in turn causes btf_type_id_size to return NULL, triggering EINVAL.
To summarise, the following conditions are necessary:
- VAR pointing at PTR, STRUCT, UNION or ARRAY
- Followed by a VAR pointing at TYPEDEF, VOLATILE, CONST, RESTRICT or
TYPE_TAG
The fix is to reset resolve_mode to RESOLVE_TBD before attempting to
resolve a VAR from a DATASEC.
Fixes: 5cc8aa5eb834 ("bpf: kernel side support for BTF Var and DataSec") Signed-off-by: Lorenz Bauer <lmb@isovalent.com> Link: https://lore.kernel.org/r/20230306112138.155352-2-lmb@isovalent.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's always the case and e.g. xdp_convert_buff_to_frame() relies on
this.
IOW, the following:
for (u32 i = 0; i < 0xdead; i++) {
xdpf = xdp_convert_buff_to_frame(&xdp);
xdp_convert_frame_to_buff(xdpf, &xdp);
}
shouldn't ever modify @xdpf's contents or the pointer itself.
However, "live packet" code wrongly treats &xdp_frame as part of its
context placed *before* the data_hard_start. With such flow,
data_hard_start is sizeof(*xdpf) off to the right and no longer points
to the XDP frame.
Instead of replacing `sizeof(ctx)` with `offsetof(ctx, xdpf)` in several
places and praying that there are no more miscalcs left somewhere in the
code, unionize ::frm with ::data in a flex array, so that both starts
pointing to the actual data_hard_start and the XDP frame actually starts
being a part of it, i.e. a part of the headroom, not the context.
A nice side effect is that the maximum frame size for this mode gets
increased by 40 bytes, as xdp_buff::frame_sz includes everything from
data_hard_start (-> includes xdpf already) to the end of XDP/skb shared
info.
Also update %MAX_PKT_SIZE accordingly in the selftests code. Leave it
hardcoded for 64 bit && 4k pages, it can be made more flexible later on.
Minor: align `&head->data` with how `head->frm` is assigned for
consistency.
Minor #2: rename 'frm' to 'frame' in &xdp_page_head while at it for
clarity.
(was found while testing XDP traffic generator on ice, which calls
xdp_convert_frame_to_buff() for each XDP frame)
Fixes: c23b8c0ec3f7 ("bpf: Add "live packet" mode for XDP in BPF_PROG_RUN") Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20230215185440.4126672-1-aleksander.lobakin@intel.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
At btrfs_drop_extent_map_range() we are clearing the EXTENT_FLAG_LOGGING
bit on a 'flags' variable that was not initialized. This makes static
checkers complain about it, so initialize the 'flags' variable before
clearing the bit.
In practice this has no consequences, because EXTENT_FLAG_LOGGING should
not be set when btrfs_drop_extent_map_range() is called, as an fsync locks
the inode in exclusive mode, locks the inode's mmap semaphore in exclusive
mode too and it always flushes all delalloc.
Also add a comment about why we clear EXTENT_FLAG_LOGGING on a copy of the
flags of the split extent map.
Reported-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/linux-btrfs/Y%2FyipSVozUDEZKow@kili/ Fixes: 6d5f4f2e44e4 ("btrfs: drop extent map range more efficiently") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booting with an initial ramdisk on platforms where physical memory
does not start at address zero (e.g. on Amiga):
initrd: 0ef0602c - 0f800000
Zone ranges:
DMA [mem 0x0000000008000000-0x000000f7ffffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000008000000-0x000000000f7fffff]
Initmem setup node 0 [mem 0x0000000008000000-0x000000000f7fffff]
Unable to handle kernel access at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<00201d3c>] memcmp+0x28/0x56
As phys_to_virt() relies on m68k_memoffset and module_fixup(), it must
not be called before paging_init(). Hence postpone the phys_to_virt
handling for the initial ramdisk until after calling paging_init().
While at it, reduce #ifdef clutter by using IS_ENABLED() instead.
The xtables packet traverser performs an unconditional local_bh_disable(),
but the nf_tables evaluation loop does not.
Functions that are called from either xtables or nftables must assume
that they can be called in process context.
inet_twsk_deschedule_put() assumes that no softirq interrupt can occur.
If tproxy is used from nf_tables its possible that we'll deadlock
trying to aquire a lock already held in process context.
Add a small helper that takes care of this and use it.
It seems that change was unintentional, we have userspace code that
needs the mark while listening for events like REPLY, DESTROY, etc.
Also include 0-marks in requested dumps, as they were before that fix.
Fixes: c7296b10ea6b ("netfilter: ctnetlink: fix compilation warning after data race fixes in ct mark") Signed-off-by: Ivan Delalande <colona@arista.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 3ad87a400c64 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.") Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The locking in phy_probe() and phy_remove() does very little to prevent
any races with e.g. phy_attach_direct(), but instead causes lockdep ABBA
warnings. Remove it.
======================================================
WARNING: possible circular locking dependency detected
6.2.0-dirty #1108 Tainted: G W E
------------------------------------------------------
ip/415 is trying to acquire lock: ffff5c268f81ef50 (&dev->lock){+.+.}-{3:3}, at: phy_attach_direct+0x17c/0x3a0 [libphy]
but task is already holding lock: ffffaef6496cb518 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x154/0x560
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Fixes: d692bc994712 ("net: phy: add core phylib sfp support") Reported-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When MAC is not support PMT, driver will check PHY's WoL capability
and set device wakeup capability in stmmac_init_phy(). We can enable
the WoL through ethtool, the driver would enable the device wake up
flag. Now the device_may_wakeup() return true.
But if there is a way which enable the PHY's WoL capability derectly,
like in BIOS. The driver would not know the enable thing and would not
set the device wake up flag. The phy_suspend may failed like this:
[ 32.409063] PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x50 returns -16
[ 32.409065] PM: Device stmmac-1:00 failed to suspend: error -16
[ 32.409067] PM: Some devices failed to suspend, or early wake event detected
Add to set the device wakeup enable flag according to the get_wol
function result in PHY can fix the error in this scene.
v2: add a Fixes tag.
Fixes: cd554d33c29a ("net: stmmac: Support WOL with phy") Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
DMA2 and DMA3 planes on msm8998 should use corresponding DMA2 and DMA3
clocks rather than CURSOR0/1 clocks (which are used for the CURSOR
planes). Correct corresponding SSPP declarations.
In this case, "copied" always is 0, the infinite loop occurs.
According to the Linux system call man page, 0 should be returned in this
case. Therefore, in tcp_bpf_recvmsg_parser(), if the length is 0, directly
return. Also modify several other functions with the same problem.
Fixes: 698fcd555908 ("udp: Implement udp_bpf_recvmsg() for sockmap") Fixes: efd2512dd28c ("af_unix: Implement unix_dgram_bpf_recvmsg()") Fixes: 653d74294f4d ("bpf, sockmap: Fix race in ingress receive verdict with redirect to self") Fixes: 38506f4bbc9d ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Cc: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230303080946.1146638-1-liujian56@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
ice_get_module_eeprom() is broken since commit 175ddf7bd78f ("ice:
Reimplement module reads used by ethtool") In this refactor,
ice_get_module_eeprom() reads the eeprom in blocks of size 8.
But the condition that should protect the buffer overflow
ignores the last block. The last block always contains zeros.
Bug uncovered by ethtool upstream commit 9538f384b535
("netlink: eeprom: Defer page requests to individual parsers")
After this commit, ethtool reads a block with length = 1;
to read the SFF-8024 identifier value.
Fixes: 175ddf7bd78f ("ice: Reimplement module reads used by ethtool") Signed-off-by: Petr Oros <poros@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported use-after-free in cfusbl_device_notify() [1]. This
causes a stack trace like below:
BUG: KASAN: use-after-free in cfusbl_device_notify+0x7c9/0x870 net/caif/caif_usb.c:138
Read of size 8 at addr ffff88807ac4e6f0 by task kworker/u4:6/1214
When unregistering a net device, unregister_netdevice_many_notify()
sets the device's reg_state to NETREG_UNREGISTERING, calls notifiers
with NETDEV_UNREGISTER, and adds the device to the todo list.
Later on, devices in the todo list are processed by netdev_run_todo().
netdev_run_todo() waits devices' reference count become 1 while
rebdoadcasting NETDEV_UNREGISTER notification.
When cfusbl_device_notify() is called with NETDEV_UNREGISTER multiple
times, the parent device might be freed. This could cause UAF.
Processing NETDEV_UNREGISTER multiple times also causes inbalance of
reference count for the module.
This patch fixes the issue by accepting only first NETDEV_UNREGISTER
notification.
Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).
Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."
I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.
Fixes: 09e8bf6570a4 ("lan78xx: workaround of forced 100 Full/Half duplex mode error") Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When creating counters with initial delay configured, the enable_on_exec
field is not set. So we need to enable the counters later. The problem
is, when a workload is specified the target__none() is true. So we also
need to check stat_config.initial_delay.
In this change, we add a new field 'initial_delay' for struct target
which could be shared by other subcommands. And define
target__enable_on_exec() which returns whether enable_on_exec should be
set on normal cases.
Fixes: 98b344effc11cb1b ("perf stat: Do not delay the workload with --delay") Signed-off-by: Changbin Du <changbin.du@huawei.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hui Wang <hw.huiwang@huawei.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20230302031146.2801588-2-changbin.du@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian reported a regression and sent a patch with the following
changelog:
<quote>
There is a noticeable tcp performance regression (loopback or cross-netns),
seen with iperf3 -Z (sendfile mode) when generic retpolines are needed.
With SK_RECLAIM_THRESHOLD checks gone number of calls to enter/leave
memory pressure happen much more often. For TCP indirect calls are
used.
We can't remove the if-set-return short-circuit check in
tcp_enter_memory_pressure because there are callers other than
sk_enter_memory_pressure. Doing a check in the sk wrapper too
reduces the indirect calls enough to recover some performance.
"iperf3 -c $peer -t 60 -Z -f g", connected via veth in another netns.
</quote>
It seems we forgot to upstream this indirect call mitigation we
had for years, lets do this instead.
[edumazet] - It seems we forgot to upstream this indirect call
mitigation we had for years, let's do this instead.
- Changed to INDIRECT_CALL_INET_1() to avoid bots reports.
ctx->crypto_send.info is not protected by lock_sock in
do_tls_getsockopt_conf(). A race condition between do_tls_getsockopt_conf()
and error paths of do_tls_setsockopt_conf() may lead to a use-after-free
or null-deref.
More discussion: https://lore.kernel.org/all/Y/ht6gQL+u6fj3dG@hog/
The test_local_dnat_portonly() function initiates the client-side as
soon as it sets the listening side to the background. This could lead to
a race condition where the server may not be ready to listen. To ensure
that the server-side is up and running before initiating the
client-side, a delay is introduced to the test_local_dnat_portonly()
function.
Before the fix:
# ./nft_nat.sh
PASS: netns routing/connectivity: ns0-rthlYrBU can reach ns1-rthlYrBU and ns2-rthlYrBU
PASS: ping to ns1-rthlYrBU was ip NATted to ns2-rthlYrBU
PASS: ping to ns1-rthlYrBU OK after ip nat output chain flush
PASS: ipv6 ping to ns1-rthlYrBU was ip6 NATted to ns2-rthlYrBU
2023/02/27 04:11:03 socat[6055] E connect(5, AF=2 10.0.1.99:2000, 16): Connection refused
ERROR: inet port rewrite
After the fix:
# ./nft_nat.sh
PASS: netns routing/connectivity: ns0-9sPJV6JJ can reach ns1-9sPJV6JJ and ns2-9sPJV6JJ
PASS: ping to ns1-9sPJV6JJ was ip NATted to ns2-9sPJV6JJ
PASS: ping to ns1-9sPJV6JJ OK after ip nat output chain flush
PASS: ipv6 ping to ns1-9sPJV6JJ was ip6 NATted to ns2-9sPJV6JJ
PASS: inet port rewrite without l3 address
Fixes: a00bd5b5d626 ("netfilter: nat: really support inet nat without l3 address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the police was removed from the port, then it was trying to
remove the police from the police id and not from the actual
police index.
The police id represents the id of the police and police index
represents the position in HW where the police is situated.
The port police id can be any number while the port police index
is a number based on the port chip port.
Fix this by deleting the police from HW that is situated at the
police index and not police id.
Fixes: 15b8f3a8fe54 ("net: lan966x: Add port police support using tc-matchall") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 688bdaed3ad7 ("ila: Add generic ILA translation facility") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Gaurav reports that TLS Rx is broken with async crypto
accelerators. The commit under fixes missed updating
the retval byte counting logic when updating how records
are stored. Even tho both before and after the change
'decrypted' was updated inside the main loop, it was
completely overwritten when processing the async
completions. Now that the rx_list only holds
non-zero-copy records we need to add, not overwrite.
It looks like U-Boot fails to start the kernel properly when the
compatible string of the board isn't fsl,T1040RDB, so stop overriding it
from the rev-a.dts.
Fixes: bd04d92fe8a1 ("powerpc: dts: t1040rdb: fix ports names for Seville Ethernet switch") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While bringing hardware up we should perform a full reset including the
switch bit (BGMAC_BCMA_IOCTL_SW_RESET aka SICF_SWRST). It's what
specification says and what reference driver does.
This seems to be critical for the BCM5358. Without this hardware doesn't
get initialized properly and doesn't seem to transmit or receive any
packets.
Originally bgmac was calling bgmac_chip_reset() before setting
"has_robosw" property which resulted in expected behaviour. That has
changed as a side effect of adding platform device support which
regressed BCM5358 support.
The rptr_addr is set in the preempt_init_ring(), which is called from
a5xx_gpu_init(). It uses shadowptr() to set the address, however the
shadow_iova is not yet initialized at that time. Move the rptr_addr
setting to the a5xx_preempt_hw_init() which is called after setting the
shadow_iova, getting the correct value for the address.
Fixes: da8cc66288a3 ("drm/msm: Allow a5xx to mark the RPTR shadow as privileged") Suggested-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/522640/ Link: https://lore.kernel.org/r/20230214020956.164473-5-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Quoting Yassine: ring->memptrs->rptr is never updated and stays 0, so
the comparison always evaluates to false and get_next_ring always
returns ring 0 thinking it isn't empty.
Fix this by calling get_rptr() instead of reading rptr directly.
Reported-by: Yassine Oudjana <y.oudjana@protonmail.com> Fixes: 2ae99dd8e304 ("drm/msm: Implement preemption for A5XX targets") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/522642/ Link: https://lore.kernel.org/r/20230214020956.164473-4-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rather than writing CP_PREEMPT_ENABLE_GLOBAL twice, follow the vendor
kernel and set CP_PREEMPT_ENABLE_LOCAL register instead. a5xx_submit()
will override it during submission, but let's get the sequence correct.
Fixes: 2ae99dd8e304 ("drm/msm: Implement preemption for A5XX targets") Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/522638/ Link: https://lore.kernel.org/r/20230214020956.164473-2-dmitry.baryshkov@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not map STATUS_OBJECT_NAME_INVALID to -EREMOTE under non-DFS
shares, or 'nodfs' mounts or CONFIG_CIFS_DFS_UPCALL=n builds.
Otherwise, in the slow path, get a referral to figure out whether it
is an actual DFS link.
This could be simply reproduced under a non-DFS share by running the
following
When we are renaming a directory to a different directory, we need to
update '..' entry in the moved directory. However nothing prevents moved
directory from being modified and even converted from the inline format
to the normal format. When such race happens the rename code gets
confused and we crash. Fix the problem by locking the moved directory.
CC: stable@vger.kernel.org Fixes: 4f33f5947495 ("ext4: let ext4_rename handle inline dir") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230126112221.11866-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove the /proc/scsi/${proc_name} directory earlier to fix a race
condition between unloading and reloading kernel modules. This fixes a bug
introduced in 2009 by commit 1f857a84ea63 ("[SCSI] fix /proc memory leak in
the SCSI core").
As explained in commit 97484fe6a145 ("block: Do not reread partition table
on exclusively open device"), reread partition on the device that is
exclusively opened by someone else is problematic.
This patch will make sure partition scan will only be proceed if current
thread open the device exclusively, or the device is not opened
exclusively, and in the later case, other scanners and exclusive openers
will be blocked temporarily until partition scan is done.
Fixes: 45703ec20f31 ("block: remove the bd_openers checks in blk_drop_partitions") Cc: <stable@vger.kernel.org> Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20230217022200.3092987-3-yukuai1@huaweicloud.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch can't fix the problem in a corner case that device can be
opened exclusively after the checking and before blkdev_get_by_dev().
We'll use a new solution to fix the problem in the next patch, and
the new solution doesn't need to change apis.
We now have some eDP+DSI dual panel systems floating around
where the DSI panel is the secondary LFP and thus needs to
consult "panel type 2" in VBT in order to locate all the
other panel type dependant stuff correctly.
To that end we need to pass in the devdata to
intel_bios_init_panel_late(), otherwise it'll just assume
we want the primary panel type. So let's try to just populate
the vbt.ports[] stuff and encoder->devdata for icl+ DSI
panels as well.
We can't do this on older platforms as there we risk a DSI
port aliasing with a HDMI/DP port, which is a totally legal
thing as the DSI ports live in their own little parallel
universe.
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Introduce a place where we can initialize connector->panel
after it's been allocated. We already have a intel_panel_init()
so had to get creative with the name and came up with
intel_panel_init_alloc().
The flash decriptor contains the number of flash components that we use
to figure out how many flash chips there are connected. Therefore we
need to read it first before deciding how many chip selects the
controller has.
Reported-by: Marcin Witkowski <marcin.witkowski@intel.com> Fixes: 8cacd7e61303 ("spi: intel: Add support for second flash chip") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20230215110040.42186-1-mika.westerberg@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
state_lock, the spinlock type is meant to protect race against concurrent
MHI state transitions. In mhi_ep_set_m0_state(), while the state_lock is
being held, the channels are resumed in mhi_ep_resume_channels() if the
previous state was M3. This causes sleeping in atomic bug, since
mhi_ep_resume_channels() use mutex internally.
Since the state_lock is supposed to be held throughout the state change,
it is not ideal to drop the lock before calling mhi_ep_resume_channels().
So to fix this issue, let's change the type of state_lock to mutex. This
would also allow holding the lock throughout all state transitions thereby
avoiding any potential race.
Cc: <stable@vger.kernel.org> # 5.19 Fixes: 9ac68db5eafd ("bus: mhi: ep: Add support for suspending and resuming channels") Reported-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During graceful shutdown scenario, host will issue MHI RESET to the
endpoint device before initiating shutdown. In that case, it makes sense
to completely power down the MHI stack as sooner or later the access to
MMIO registers will be prohibited. Also, the stack needs to be powered
up in the case of SYS_ERR to recover the device.
The condition determining whether the preallocation can be used had
an off-by-one error so we didn't discard preallocation when new
allocation was just following it. This can then confuse code in
inode_getblk().
CC: stable@vger.kernel.org Fixes: 189b02ac597c ("udf: Discard preallocation before extending file with a hole") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch sets the stop tx flag before we commit the dlm message.
This flag will report about unexpected transmissions after we
send the DLM_FIN message out, which should be the last message sent.
When we commit the dlm fin message, it could be that we already
got an ack back and the CLOSED state change already happened.
We should not set this flag when we are in CLOSED state. To avoid this
race we simply set the tx flag before the state change can be in
progress by moving it before dlm_midcomms_commit_mhandle().
Cc: stable@vger.kernel.org Fixes: 9c99c76781ff ("fs: dlm: add reliable connection if reconnect") Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we release a midcomms node structure, there should be nothing left
inside the dlm midcomms send queue. However, sometimes this is not true
because I believe some DLM_FIN message was not acked... if we run
into a shutdown timeout, then we should be sure there is no pending send
dlm message inside this queue when releasing midcomms node structure.
Cc: stable@vger.kernel.org Fixes: 9c99c76781ff ("fs: dlm: add reliable connection if reconnect") Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To not get the console spammed about WARN_ON() of invalid states in the
dlm midcomms hot path handling we switch to WARN_ON_ONCE() to get it
only once that there might be an issue with the midcomms state handling.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: 557856c7140b ("fs: dlm: be sure to call dlm_send_queue_flush()") Signed-off-by: Sasha Levin <sashal@kernel.org>
[ 151.834900] The buggy address belongs to the object at ffff88811a980c30
which belongs to the cache dlm_mhandle of size 88
[ 151.836894] The buggy address is located 48 bytes inside of
88-byte region [ffff88811a980c30, ffff88811a980c88)
[ 151.845822] Memory state around the buggy address:
[ 151.846602] ffff88811a980b00: fb fb fb fb fc fc fc fc fa fb fb fb fb fb fb fb
[ 151.847761] ffff88811a980b80: fb fb fb fc fc fc fc fa fb fb fb fb fb fb fb fb
[ 151.848921] >ffff88811a980c00: fb fb fc fc fc fc fa fb fb fb fb fb fb fb fb fb
[ 151.850076] ^
[ 151.851085] ffff88811a980c80: fb fc fc fc fc fa fb fb fb fb fb fb fb fb fb fb
[ 151.852269] ffff88811a980d00: fc fc fc fc fa fb fb fb fb fb fb fb fb fb fb fc
[ 151.853428] ==================================================================
[ 151.855618] Disabling lock debugging due to kernel taint
It is accessing a mhandle in dlm_midcomms_commit_mhandle() and the mhandle
was freed by a call_rcu() call in dlm_process_incoming_buffer(),
dlm_mhandle_delete(). It looks like it was freed because an ack of
this message was received. There is a short race between committing the
dlm message to be transmitted and getting an ack back. If the ack is
faster than returning from dlm_midcomms_commit_msg_3_2(), then we run
into a use-after free because we still need to reference the mhandle when
calling srcu_read_unlock().
To avoid that, we don't allow that mhandle to be freed between
dlm_midcomms_commit_msg_3_2() and srcu_read_unlock() by using rcu read
lock. We can do that because mhandle is protected by rcu handling.
Cc: stable@vger.kernel.org Fixes: 9c99c76781ff ("fs: dlm: add reliable connection if reconnect") Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds tracepoints for send and recv cases of dlm messages and
dlm rcom messages. In case of send and dlm message we add the dlm rsb
resource name this dlm messages belongs to. This has the advantage to
follow dlm messages on a per lock basis. In case of recv message the
resource name can be extracted by follow the send message sequence
number.
The dlm message DLM_MSG_PURGE doesn't belong to a lock request and will
not set the resource name in a dlm_message trace. The same for all rcom
messages.
There is additional handling required for this debugging functionality
which is tried to be small as possible. Also the midcomms layer gets
aware of lock resource names, for now this is required to make a
connection between sequence number and lock resource names. It is for
debugging purpose only.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: caf2799e0b84 ("fs: dlm: fix use after free in midcomms commit") Signed-off-by: Sasha Levin <sashal@kernel.org>
To allow more than just dereferencing the inner header we directly point
to the inner dlm packet which allows us to dereference the header, rcom
or message structure.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: caf2799e0b84 ("fs: dlm: fix use after free in midcomms commit") Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch removes the send repeat remove handling. This handling is
there to repeatingly DLM_MSG_REMOVE messages in cases the dlm stack
thinks it was not received at the first time. In cases of message drops
this functionality is necessary, but since the DLM midcomms layer
guarantees there are no messages drops between cluster nodes this
feature became not strict necessary anymore. Due message
delays/processing it could be that two send_repeat_remove() are sent out
while the other should be still on it's way. We remove the repeat remove
handling because we are sure that the message cannot be dropped due
communication errors.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: caf2799e0b84 ("fs: dlm: fix use after free in midcomms commit") Signed-off-by: Sasha Levin <sashal@kernel.org>
The scand kthread can send dlm messages out, especially dlm remove
messages to free memory for unused rsb on other nodes. To send out dlm
messages, midcomms must be initialized. This patch moves the midcomms
start before scand is started.
Cc: stable@vger.kernel.org Fixes: ae5bef69e6aa ("[DLM] The core of the DLM for GFS2/CLVM") Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch introduces leftovers of init, start, stop and exit
functionality. The dlm application layer should always call the midcomms
layer which getting aware of such event and redirect it to the lowcomms
layer. Some functionality which is currently handled inside the start
functionality of midcomms and lowcomms should be handled in the init
functionality as it only need to be initialized once when dlm is loaded.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: 5282c6801f3b ("fs: dlm: start midcomms before scand") Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch will fix a small issue when printing out that
dlm_midcomms_start() failed to start and it was printing out that the
dlm subcomponent lowcomms was failed but lowcomms is behind the midcomms
layer.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com>
Stable-dep-of: 5282c6801f3b ("fs: dlm: start midcomms before scand") Signed-off-by: Sasha Levin <sashal@kernel.org>
Call kvm_init() only after _all_ setup is complete, as kvm_init() exposes
/dev/kvm to userspace and thus allows userspace to create VMs (and call
other ioctls). E.g. KVM will encounter a NULL pointer when attempting to
add a vCPU to the per-CPU loaded_vmcss_on_cpu list if userspace is able to
create a VM before vmx_init() configures said list.
Move the guts of kvm_arch_init() to a new helper, kvm_x86_vendor_init(),
so that VMX can do _all_ arch and vendor initialization before calling
kvm_init(). Calling kvm_init() must be the _very_ last step during init,
as kvm_init() exposes /dev/kvm to userspace, i.e. allows creating VMs.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221130230934.1014142-14-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: 3c3b35a745e3 ("KVM: VMX: Do _all_ initialization before exposing /dev/kvm to userspace") Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't disable the eVMCS static key on module exit, kvm_intel.ko owns the
key so there can't possibly be users after the kvm_intel.ko is unloaded,
at least not without much bigger issues.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20221130230934.1014142-12-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: 3c3b35a745e3 ("KVM: VMX: Do _all_ initialization before exposing /dev/kvm to userspace") Signed-off-by: Sasha Levin <sashal@kernel.org>
Reset the eVMCS controls in the per-CPU VP assist page during hardware
disabling instead of waiting until kvm-intel's module exit. The controls
are activated if and only if KVM creates a VM, i.e. don't need to be
reset if hardware is never enabled.
Doing the reset during hardware disabling will naturally fix a potential
NULL pointer deref bug once KVM disables CPU hotplug while enabling and
disabling hardware (which is necessary to fix a variety of bugs). If the
kernel is running as the root partition, the VP assist page is unmapped
during CPU hot unplug, and so KVM's clearing of the eVMCS controls needs
to occur with CPU hot(un)plug disabled, otherwise KVM could attempt to
write to a CPU's VP assist page after it's unmapped.
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20221130230934.1014142-11-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: 3c3b35a745e3 ("KVM: VMX: Do _all_ initialization before exposing /dev/kvm to userspace") Signed-off-by: Sasha Levin <sashal@kernel.org>
cb_context should be freed on the error path in nfc_se_io as stated by
commit 51e42304a409 ("nfc: fix memory leak of se_io context in
nfc_genl_se_io").
Make the error path in nfc_se_io unwind everything in reverse order, i.e.
free the cb_context after unlocking the device.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230306212650.230322-1-pchelkin@ispras.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default maximum data buffer size for this interface is UHID_DATA_MAX
(4k). When data buffers are being processed, ensure this value is used
when ensuring the sanity, rather than a value between the user provided
value and HID_MAX_BUFFER_SIZE (16k).
Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently, when a report is processed, its proposed size, provided by
the user of the API (as Report Size * Report Count) is compared against
the subsystem default HID_MAX_BUFFER_SIZE (16k). However, some
low-level HID drivers allocate a reduced amount of memory to their
buffers (e.g. UHID only allocates UHID_DATA_MAX (4k) buffers), rending
this check inadequate in some cases.
In these circumstances, if the received report ends up being smaller
than the proposed report size, the remainder of the buffer is zeroed.
That is, the space between sizeof(csize) (size of the current report)
and the rsize (size proposed i.e. Report Size * Report Count), which can
be handled up to HID_MAX_BUFFER_SIZE (16k). Meaning that memset()
shoots straight past the end of the buffer boundary and starts zeroing
out in-use values, often resulting in calamity.
This patch introduces a new variable into 'struct hid_ll_driver' where
individual low-level drivers can over-ride the default maximum value of
HID_MAX_BUFFER_SIZE (16k) with something more sympathetic to the
interface.
Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the boot loader inode has never been used before, the
EXT4_IOC_SWAP_BOOT inode will initialize it, including setting the
i_size to 0. However, if the "never before used" boot loader has a
non-zero i_size, then i_disksize will be non-zero, and the
inconsistency between i_size and i_disksize can trigger a kernel
warning:
Above issue happens as follows:
ext4_iget
ext4_find_inline_data_nolock ->i_inline_off=164 i_inline_size=60
ext4_try_add_inline_entry
__ext4_mark_inode_dirty
ext4_expand_extra_isize_ea ->i_extra_isize=32 s_want_extra_isize=44
ext4_xattr_shift_entries
->after shift i_inline_off is incorrect, actually is change to 176
ext4_try_add_inline_entry
ext4_update_inline_dir
get_max_inline_xattr_value_size
if (EXT4_I(inode)->i_inline_off)
entry = (struct ext4_xattr_entry *)((void *)raw_inode +
EXT4_I(inode)->i_inline_off);
free += EXT4_XATTR_SIZE(le32_to_cpu(entry->e_value_size));
->As entry is incorrect, then 'free' may be negative
ext4_update_inline_data
value = kzalloc(len, GFP_NOFS);
-> len is unsigned int, maybe very large, then trigger warning when
'kzalloc()'
To resolve the above issue we need to update 'i_inline_off' after
'ext4_xattr_shift_entries()'. We do not need to set
EXT4_STATE_MAY_INLINE_DATA flag here, since ext4_mark_inode_dirty()
already sets this flag if needed. Setting EXT4_STATE_MAY_INLINE_DATA
when it is needed may trigger a BUG_ON in ext4_writepages().
Reported-by: syzbot+d30838395804afc2fa6f@syzkaller.appspotmail.com Cc: stable@kernel.org Signed-off-by: Ye Bin <yebin10@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230307015253.2232062-3-yebin@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only caller of ext4_find_inline_data_nolock() that needs setting of
EXT4_STATE_MAY_INLINE_DATA flag is ext4_iget_extra_inode(). In
ext4_write_inline_data_end() we just need to update inode->i_inline_off.
Since we are going to add one more caller that does not need to set
EXT4_STATE_MAY_INLINE_DATA, just move setting of EXT4_STATE_MAY_INLINE_DATA
out to ext4_iget_extra_inode().
Signed-off-by: Ye Bin <yebin10@huawei.com> Cc: stable@kernel.org Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230307015253.2232062-2-yebin@huaweicloud.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For GETFSMAP calls, the caller selects a physical block device by
writing its block number into fsmap_head.fmh_keys[01].fmr_device.
To query mappings for a subrange of the device, the starting byte of the
range is written to fsmap_head.fmh_keys[0].fmr_physical and the last
byte of the range goes in fsmap_head.fmh_keys[1].fmr_physical.
IOWs, to query what mappings overlap with bytes 3-14 of /dev/sda, you'd
set the inputs as follows:
Which would return you whatever is mapped in the 12 bytes starting at
physical offset 3.
The crash is due to insufficient range validation of keys[1] in
ext4_getfsmap_datadev. On 1k-block filesystems, block 0 is not part of
the filesystem, which means that s_first_data_block is nonzero.
ext4_get_group_no_and_offset subtracts this quantity from the blocknr
argument before cracking it into a group number and a block number
within a group. IOWs, block group 0 spans blocks 1-8192 (1-based)
instead of 0-8191 (0-based) like what happens with larger blocksizes.
The net result of this encoding is that blocknr < s_first_data_block is
not a valid input to this function. The end_fsb variable is set from
the keys that are copied from userspace, which means that in the above
example, its value is zero. That leads to an underflow here:
Leaving an impossibly large group number (2^32-1) in blocknr.
ext4_getfsmap_check_keys checked that keys[0].fmr_physical and
keys[1].fmr_physical are in increasing order, but
ext4_getfsmap_datadev adjusts keys[0].fmr_physical to be at least
s_first_data_block. This implies that we have to check it again after
the adjustment, which is the piece that I forgot.
A significant number of xfstests can cause ext4 to log one or more
warning messages when they are run on a test file system where the
inline_data feature has been enabled. An example:
"EXT4-fs warning (device vdc): ext4_dirblock_csum_set:425: inode
#16385: comm fsstress: No space for directory leaf checksum. Please
run e2fsck -D."
The xfstests include: ext4/057, 058, and 307; generic/013, 051, 068,
070, 076, 078, 083, 232, 269, 270, 390, 461, 475, 476, 482, 579, 585,
589, 626, 631, and 650.
In this situation, the warning message indicates a bug in the code that
performs the RENAME_WHITEOUT operation on a directory entry that has
been stored inline. It doesn't detect that the directory is stored
inline, and incorrectly attempts to compute a dirent block checksum on
the whiteout inode when creating it. This attempt fails as a result
of the integrity checking in get_dirent_tail (usually due to a failure
to match the EXT4_FT_DIR_CSUM magic cookie), and the warning message
is then emitted.
Fix this by simply collecting the inlined data state at the time the
search for the source directory entry is performed. Existing code
handles the rest, and this is sufficient to eliminate all spurious
warning messages produced by the tests above. Go one step further
and do the same in the code that resets the source directory entry in
the event of failure. The inlined state should be present in the
"old" struct, but given the possibility of a race there's no harm
in taking a conservative approach and getting that information again
since the directory entry is being reread anyway.
Fixes: 7ef4b1da17dd ("ext4: find old entry again if failed to rename whiteout") Cc: stable@kernel.org Signed-off-by: Eric Whitney <enwlinux@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230210173244.679890-1-enwlinux@gmail.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When writing a page from an encrypted file that is using
filesystem-layer encryption (not inline encryption), ext4 encrypts the
pagecache page into a bounce page, then writes the bounce page.
It also passes the bounce page to wbc_account_cgroup_owner(). That's
incorrect, because the bounce page is a newly allocated temporary page
that doesn't have the memory cgroup of the original pagecache page.
This makes wbc_account_cgroup_owner() not account the I/O to the owner
of the pagecache page as it should.
Fix this by always passing the pagecache page to
wbc_account_cgroup_owner().
To last 2 parameters to cfg80211_get_bss() should be of
the enum ieee80211_bss_type resp. enum ieee80211_privacy types,
which WLAN_CAPABILITY_ESS very much is not.
Fix both cfg80211_get_bss() calls in ioctl_cfg80211.c to pass
the right parameters.
Note that the second call was already somewhat fixed by commenting
out WLAN_CAPABILITY_ESS and passing in 0 instead. This was still
not entirely correct though since that would limit returned
BSS-es to ESS type BSS-es with privacy on.
There are 2 issues with the key-store index handling
1. The non WEP key stores can store keys with indexes 0 - BIP_MAX_KEYID,
this means that they should be an array with BIP_MAX_KEYID + 1
entries. But some of the arrays where just BIP_MAX_KEYID entries
big. While one other array was hardcoded to a size of 6 entries,
instead of using the BIP_MAX_KEYID define.
2. The rtw_cfg80211_set_encryption() and wpa_set_encryption() functions
index check where checking that the passed in key-index would fit
inside both the WEP key store (which only has 4 entries) as well as
in the non WEP key stores. This breaks any attempts to set non WEP
keys with index 4 or 5.
Issue 2. specifically breaks wifi connection with some access points
which advertise PMF support. Without this fix connecting to these
access points fails with the following wpa_supplicant messages:
nl80211: kernel reports: key addition failed
wlan0: WPA: Failed to configure IGTK to the driver
wlan0: RSN: Failed to configure IGTK
wlan0: CTRL-EVENT-DISCONNECTED bssid=... reason=1 locally_generated=1
Fix 1. by using the right size for the key-stores. After this 2. can
safely be fixed by checking the right max-index value depending on the
used algorithm, fixing wifi not working with some PMF capable APs.
The EDID of an HDR display defines EOTFs that are supported
by the display and can be set in the HDR metadata infoframe.
Userspace is expected to read the EDID and set an appropriate
HDR_OUTPUT_METADATA.
In drm_parse_hdr_metadata_block the kernel reads the supported
EOTFs from the EDID and stores them in the
drm_connector->hdr_sink_metadata. While doing so it also
filters the EOTFs to the EOTFs the kernel knows about.
When an HDR_OUTPUT_METADATA is set it then checks to
make sure the EOTF is a supported EOTF. In cases where
the kernel doesn't know about a new EOTF this check will
fail, even if the EDID advertises support.
Since it is expected that userspace reads the EDID to understand
what the display supports it doesn't make sense for DRM to block
an HDR_OUTPUT_METADATA if it contains an EOTF the kernel doesn't
understand.
This comes with the added benefit of future-proofing metadata
support. If the spec defines a new EOTF there is no need to
update DRM and an compositor can immediately make use of it.
The RISC-V ELF attributes don't contain any useful information. New
toolchains ignore them, but they frequently trip up various older/mixed
toolchains. So just turn them off.
Currently, calling clone3() with CLONE_NEWTIME in clone_args->flags
fails with -EINVAL. This is because CLONE_NEWTIME intersects with
CSIGNAL. However, CSIGNAL was deprecated when clone3 was introduced in
commit 2857618838c4 ("fork: add clone3"), allowing re-use of that part
of clone flags.
Fix this by explicitly allowing CLONE_NEWTIME in clone3_args_valid. This
is also in line with the respective check in check_unshare_flags which
allow CLONE_NEWTIME for unshare().
Fixes: 6863f52c2620 ("ns: Introduce Time Namespace") Cc: Andrey Vagin <avagin@openvz.org> Cc: Christian Brauner <brauner@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MMAP2 has the PERF_RECORD_MISC_MMAP_BUILD_ID flag, it means the
record already has the build-id info. So it marks the DSO as hit, to
skip if the same DSO is not processed if it happens to miss the build-id
later.
But it missed to copy the MMAP2 record itself so it'd fail to symbolize
samples for those regions.
For example, the following generates 249 MMAP2 events.
Fixes: 4b1fc378efa46bd6 ("perf inject: Do not inject BUILD_ID record if MMAP2 has it") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230223070155.54251-1-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible for a file type to support uring commands, but not
pollable ones. Hence before issuing one of those, we should check
that it is supported and error out upfront if it isn't.
Current btrfs_log_dev_io_error() increases the read error count even if the
erroneous IO is a WRITE request. This is because it forget to use "else
if", and all the error WRITE requests counts as READ error as there is (of
course) no REQ_RAHEAD bit set.
Fixes: a2e928f27856 ("btrfs: use chained bios when cloning") CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove call_usermodehelper starting /etc/acpi/events/RadioPower.sh that
is not available. This script is not part of the kernel and it is not
officially available on the www. The result is that this lines are just
dead code.
Remove function _rtl92e_dm_check_ac_dc_power calling a script
/etc/acpi/wireless-rtl-ac-dc-power.sh that is not available. This script
is not part of the kernel and it is not available on the www. The result
is that this function is just dead code.
AMD has issued an advisory indicating that having fTPM enabled in
BIOS can cause "stuttering" in the OS. This issue has been fixed
in newer versions of the fTPM firmware, but it's up to system
designers to decide whether to distribute it.
This issue has existed for a while, but is more prevalent starting
with kernel 6.1 because commit 532eae4a1ecd8 ("hwrng: core - start
hwrng kthread also for untrusted sources") started to use the fTPM
for hwrng by default. However, all uses of /dev/hwrng result in
unacceptable stuttering.
So, simply disable registration of the defective hwrng when detecting
these faulty fTPM versions. As this is caused by faulty firmware, it
is plausible that such a problem could also be reproduced by other TPM
interactions, but this hasn't been shown by any user's testing or reports.
It is hypothesized to be triggered more frequently by the use of the RNG
because userspace software will fetch random numbers regularly.
Intentionally continue to register other TPM functionality so that users
that rely upon PCR measurements or any storage of data will still have
access to it. If it's found later that another TPM functionality is
exacerbating this problem a module parameter it can be turned off entirely
and a module parameter can be introduced to allow users who rely upon
fTPM functionality to turn it on even though this problem is present.
Link: https://www.amd.com/en/support/kb/faq/pa-410 Link: https://bugzilla.kernel.org/show_bug.cgi?id=216989 Link: https://lore.kernel.org/all/20230209153120.261904-1-Jason@zx2c4.com/ Fixes: 532eae4a1ecd ("hwrng: core - start hwrng kthread also for untrusted sources") Cc: stable@vger.kernel.org Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: Thorsten Leemhuis <regressions@leemhuis.info> Cc: James Bottomley <James.Bottomley@hansenpartnership.com> Tested-by: reach622@mailcuk.com Tested-by: Bell <1138267643@qq.com> Co-developed-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log