Arnd Bergmann [Fri, 28 Nov 2014 11:36:43 +0000 (12:36 +0100)]
Merge tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "temporarily disable rk3288-smp" from Heiko Stuebner:
Disable smp again on rk3288 temporarily to make Olof's boottest
run again, until the patches for using the physical architected
timers got accepted.
* tag 'v3.19-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: temporarily disable smp on rk3288
Pankaj Dubey [Wed, 26 Nov 2014 18:24:45 +0000 (03:24 +0900)]
ARM: dts: add sysreg phandle to i2c device nodes for exynos
This patch adds syscon based phandle to i2c device nodes of exynos5250
and exynos5420. These phandles will be used to save restore i2c sysreg
configuration register during s2r from i2c driver.
CC: Rob Herring <robh+dt@kernel.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Russell King <linux@arm.linux.org.uk> CC: devicetree@vger.kernel.org CC: linux-doc@vger.kernel.org Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Youngjun Cho [Wed, 26 Nov 2014 17:43:39 +0000 (02:43 +0900)]
ARM: dts: add board dts file for Exynos3250-based Monk board
This patch adds new board dts file to support Samsung Monk board which
is based on Exynos3250 SoC and has different H/W configuration from
Rinato.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Youngjun Cho <yj44.cho@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Roger Quadros [Wed, 29 Oct 2014 15:52:57 +0000 (17:52 +0200)]
ARM: dts: am335x-evm: Add DCAN1 details
DCAN1 is routed to CAN port (J11) when Profile 1 is selected on the
profile selection switch.
Provide information for DCAN1 pins and node but keep it disabled
by default. User has to manually enable it if Profile 1 is chosen.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 9 Sep 2014 13:15:35 +0000 (16:15 +0300)]
ARM: dts: am33xx: Update DCAN nodes
Add "raminit-syscon" property to specify the RAMINIT register.
Add clock information.
Rename can nodes from "d_can" to "can" to be compliant
with the ePAPR specs.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Fri, 18 Jul 2014 05:59:11 +0000 (11:29 +0530)]
ARM: dts: am437x-gp: Add dcan support
Add DCAN support for AM437x GP EVM with both DCAN instances.
[Roger Q] Updated output pin to not use pull up.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Heiko Stuebner [Sat, 22 Nov 2014 15:23:28 +0000 (16:23 +0100)]
ARM: dts: rockchip: temporarily disable smp on rk3288
Stock firmware on rk3288 does not initizalize the CNTVOFF registers
of the architected timer correctly. This introduces issues with the
newly added SMP support for rk3288, resulting in rcu stalls due to
differing timer values per core.
There exist preliminary and tested patches for u-boot for this problem,
but there are a minority of boards using other bootloaders like coreboot.
There also is currently a second solution for miss-initialized architected
timers in the works:
- clocksource: arch_timer: Fix code to use physical timers when requested
- clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
Therefore disable smp on rk3288 again till these are finalized, also
allowing coreboot-based boards to boot again.
Marek Szyprowski [Sat, 22 Nov 2014 14:44:11 +0000 (23:44 +0900)]
ARM: dts: add missing clock to MFC device for exynos4
sclk_mfc is required for MFC device since commit 41ec5065d1ea8a73f86420faefdcf799646cc37b ("media: s5p-mfc: rename
special clock to sclk_mfc"), so add it to exynos4 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: dts: Specify audio clock parents and rates for exynos4412-odroid-common
This ensures the core and the audio subsystem clocks are configured
properly, as expected by the sound machine driver. These bits are
missing to obtain proper audio sample rates in kernel v3.17, where
audio support for Odroid X2/U3 was first added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas Faerber [Sat, 22 Nov 2014 14:31:13 +0000 (23:31 +0900)]
ARM: dts: Add trackpad to exynos5250-spring
The HP Chromebook 11 uses an Atmel maXTouch as trackpad.
The keymap was found by trial-and-error.
Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas Faerber [Sat, 22 Nov 2014 14:31:07 +0000 (23:31 +0900)]
ARM: dts: Add temperature sensor to exynos5250-spring
Spotted in the Chrome OS 3.8 based device tree.
Needs CONFIG_SENSORS_LM90.
Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas Faerber [Sat, 22 Nov 2014 14:31:03 +0000 (23:31 +0900)]
ARM: dts: Add usb3503 pinctrl to exynos5250-spring
Reported-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Andreas Faerber <afaerber@suse.de> Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARM: dts: Specify default clocks for Exynos4 camera devices
Specify the default mux and divider clocks in device tree
to ensure the FIMC devices on Trats, Trats2, Universal_c210
and Odroid X2/U3 boards are clocked from recommended clock
source and with maximum supported frequency.
For Trats2 also the MIPI-CSIS and the camera sensor clocks
are configured, the 'clock-frequency' property is deprecated
in favour of 'assigned-clock-rates' property.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adam YH Lee [Thu, 13 Nov 2014 18:04:33 +0000 (10:04 -0800)]
ARM: dts: Gumstix DuoVero: Bind vdac regulator to hdmi node
The HDMI node does not have a power supply attached. As a result its
power regulator, VDAC, shuts off on boot and screen loses signal.
This attaches VDAC (vdda_hdmi_dac) to HDMI's vdda-supply.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Arnd Bergmann [Fri, 21 Nov 2014 12:02:08 +0000 (13:02 +0100)]
Merge tag 'renesas-dt2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Second Round of Renesas ARM Based SoC DT Updates for v3.19" from Simon Horman:
* Add labels for LEDs on kzm9g-reference and koelsch
* Add Sound support to r8a7790/lager and r8a7791/koelsch
* Add IIC DMA nodes to r8a7790 and r8a7791
* Use SoC-specific IIC compatible properties on sh73a0 and r8a73a4
* Add SGX, MMP and VSP1 clocks to r8a7794
* Add USBDMAC{0,1} clocks to r8a7790 and r8a7791
* tag 'renesas-dt2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
ARM: shmobile: r8a7791: add USBDMAC{0,1} clocks to device tree
ARM: shmobile: r8a7790: add USBDMAC{0,1} clocks to device tree
ARM: shmobile: r8a7794: Add MMP and VSP1 clocks to device tree
ARM: shmobile: r8a7794: Add SGX clock to device tree
ARM: shmobile: koelsch: add Volume Ramp usage on comment
ARM: shmobile: lager: add Volume Ramp usage on comment
ARM: shmobile: r8a7791: add DMA nodes for IIC
ARM: shmobile: r8a7790: add DMA nodes for IIC
ARM: shmobile: kzm9g-reference dts: Add labels for the LEDs
ARM: shmobile: koelsch dts: Add labels for the LEDs
ARM: shmobile: sh73a0 dtsi: Add SoC-specific IIC compatible properties
ARM: shmobile: r8a73a4 dtsi: Add SoC-specific IIC compatible properties
ARM: shmobile: koelsch: Sound DMA support via DVC on DTS
ARM: shmobile: koelsch: Sound DMA support via SRC on DTS
ARM: shmobile: koelsch: Sound DMA support via BUSIF on DTS
ARM: shmobile: koelsch: Sound DMA support on DTS
ARM: shmobile: koelsch: Sound PIO support on DTS
ARM: shmobile: koelsch: fixup I2C2 clock frequency
ARM: shmobile: lager: Sound DMA support via DVC on DTS
ARM: shmobile: lager: Sound DMA support via SRC on DTS
...
Arnd Bergmann [Fri, 21 Nov 2014 11:57:30 +0000 (12:57 +0100)]
Merge tag 'berlin-dt-3.19-2' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Pull "Berlin DT changes for v3.19 (round 2)" from Sebastian Hesselbarth:
- AHCI and SATA PHY nodes for BG2
- USB and USB PHZ nodes for BG2/BG2CD/BG2Q
* tag 'berlin-dt-3.19-2' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: enable USB on the Google Chromecast
ARM: dts: berlin: add BG2CD nodes for USB support
ARM: dts: Berlin: enable USB on the BG2Q DMP
ARM: dts: berlin: add BG2Q nodes for USB support
ARM: berlin: Enable SATA on Sony NSZ-GS7
ARM: berlin: Add AHCI and SATA PHY nodes to BG2
arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC
The Arria 10 is latest SOC+FPGA from the Altera SOCFPGA platform. The Arria10
SOC shares some similarities with the SOCFPGA Cyclone5 and Arria5, but there
are enough differences to warrant a new base dtsi.
The differences are:
* 3 EMAC controllers
* 5 I2C controllers
* 3 SPI controllers
* 1.5 GHZ dual A9s
* Support for DDR4
Besides the usual memory map and IRQ changes, the clock framework will be
different, so this patch just adds the fixed-clocks.
Arnd Bergmann [Thu, 20 Nov 2014 16:42:17 +0000 (17:42 +0100)]
Merge tag 'v3.19-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "ARM: rockchip: second batch of dts related changes" from Heiko Stuebner:
- the dts part of the rk3288 smp support
- rate init for rk3288 clocks
- enablement of various peripherals
- new boardfile for Haoyu Marsboard (rk3066 based)
* tag 'v3.19-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable PWM on Radxa Rock
ARM: dts: rockchip: fix invalid unit-address in rk3188.dtsi
ARM: dts: rk3288: add VOP iommu nodes
ARM: dts: rockchip: add reset for CPU nodes
ARM: dts: rockchip: add intmem node for rk3288 smp support
ARM: dts: rockchip: add pmu references to cpus nodes
ARM: dts: rockchip: add serial aliases for rk3066 and rk3188
ARM: dts: rockchip: Add devicetree source for MarsBoard RK3066
ARM: dts: rockchip: Add EMAC Rockchip for RK3066 SoCs
Arnd Bergmann [Thu, 20 Nov 2014 16:39:59 +0000 (17:39 +0100)]
Merge tag 'sunxi-dt-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner Device Tree Changes for 3.19" from Maxime Ripard:
A lot of things happened during that merge window, but mostly:
- Preliminary Support for the A80
- New Boards Support
+ Mele M3
+ Banana Pi
+ Optimus
+ OLinuXino Lime2
- Device Tree Relicensing to GPLv2/X11 dual license
* tag 'sunxi-dt-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (52 commits)
ARM: dts: sun6i: Add ethernet support to M9 board
ARM: sun6i: DT: Add PLL6 multiple outputs
ARM: dts: sun6i: Add support for the status led
ARM: dts: sun6i: Add EHCI support for the M9 board
ARM: dts: sunxi: Add regulator-boot-on property to ahci-5v regulator
ARM: dts: sun7i: Cubietruck: add power supply regulator for USB OTG VBUS
ARM: dts: sun7i: Cubietruck: override regulator pin
ARM: sun7i: dtsi: add support for usbphy0
ARM: dtsi: sunxi: add common VBUS regulator
ARM: dts: sunxi: Banana Pi: increase startup-delay for the GMAC PHY regulator
ARM: dts: sunxi: Use sun4i-a10-apb1-clk for sun6i/sun8i apb2 clocks.
ARM: dts: sunxi: unify APB1 clock
ARM: dts: sun6i: Re-parent ahb1_mux to pll6 as required by dma controller
ARM: sun5i: olinuxino: Relicense the device tree under GPLv2/X11
ARM: sun4i: cubieboard: Relicense the device tree under GPLv2/X11
ARM: sun7i: pcduino3: Relicense the device tree under GPLv2/X11
ARM: sun4i: pcduino: Relicense the device tree under GPLv2/X11
ARM: sun7i: olinuxino lime: Relicense the device tree under GPLv2/X11
ARM: dts: sun9i: Enable uart4 for A80 Optimus board
ARM: dts: sun9i: Add uart4 pinmux setting for A80 SoC
...
Arnd Bergmann [Thu, 20 Nov 2014 16:38:09 +0000 (17:38 +0100)]
Merge tag 'v3.19-meson-dts' of https://github.com/carlocaione/linux-meson into next/dt
Pull "ARM: meson: DTS related changes" from Carlo Caione:
here is the pull request for the DT related changes for the 3.19.
It's mainly the work done by Beniamino for the preliminary support of
the Amlogic Meson8 SoC, the support for L2 cache and the I2C
controller.
Please note that the support for the Tronsmart S89 Elite TV box has not
been included since the Meson8 development will be done now on a
different dev board kindly provided by Amlogic.
* tag 'v3.19-meson-dts' of https://github.com/carlocaione/linux-meson:
ARM: dts: meson: add I2C controller nodes
ARM: meson: DTS: enable L2 cache
ARM: dts: add dtsi for Amlogic Meson8 SoCs
DTS: meson: Add forgotten compatible in board DTS
Arnd Bergmann [Thu, 20 Nov 2014 12:45:22 +0000 (13:45 +0100)]
Merge tag 'v3.19-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Pull "Add support for mt6592, mt8127 and mt8135 Socs from Mediatek"
from Matthias Brugger:
Here comes the pull request which introduces basic support for
Mediatek SoCs mt6592, mt8127 and mt8135.
The patches for the mt81xx got merged in the late tree for v3.18 but
were not be merged at the end. They got a small fix regarding the
compatible and model string in the dts files.
* tag 'v3.19-next-dts' of https://github.com/mbgg/linux-mediatek:
dt-bindings: add documentation for Mediatek SoC
ARM: mediatek: add dts for mt6592-evb
ARM: mediatek: Add basic support for mt6592
dt-bindings: add more chips in documentation for Mediatek SoC
ARM: dts: Build dtb for mt8127 & mt8135
ARM: mediatek: add dts for MT8135 evaluation board.
ARM: mediatek: Add basic support for mt8135
ARM: mediatek: add dts for 8127 Moose board
ARM: mediatek: Add basic support for mt8127
Arnd Bergmann [Thu, 20 Nov 2014 11:52:01 +0000 (12:52 +0100)]
Merge tag 'arm-soc/for-3.19/cygnus-dts-v2' of http://github.com/brcm/linux into next/dt
Pull "Broadcom Cygnus SoC Device Tree changes" from Florian Fainelli:
This pull request contains the Broadcom Cygnus Device Tree changes:
- binding documentation for the SoC and clock
- cygnus SoC and clock dtsi files
- DTS for Cygnus Entreprise phone, BCM911360K and BCM958300K
* tag 'arm-soc/for-3.19/cygnus-dts-v2' of http://github.com/brcm/linux:
ARM: dts: Enable Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
[arnd: something went wrong here, we already had pulled an earlier
version of the same patches, which had the wrong license statement.
I've pulled this one over the old pull request and fixed up the
conflicts now]
arch: arm: boot: dts: Correct vendor-prefix for iio device isl29028 in compatible property
This patch corrects the vendor-prefix for isl29028 in the compatible property from
"isil,isl29028" to "isl,isl29028" according to listed vendor-prefixes in
Documentation/devicetree/bindings/vendor-prefixes.txt. Incorrect vendor-prefix "isl"
was reported by checkpatch.pl warning for drivers/staging/iio/light/isl29028.c.
Thus incorrect vendor-prefix "isil" was corrected for every mention of device isl29028.
Staging: iio: light: Added correct vendor-prefix for device isl29028
This patch adds the correct vendor-prefix for device isl29028 and
maintains deprecated vendor-prefix found by checkpatch warning
for older kernel releases.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Document deprecated device vendor name to fix related warning
This patch documents deprecated vendor name "isil" to fix warning of
undocumented string for device isl29028 as reported while running checkpatch.pl
on drivers/staging/iio/light/isl29028.c. This is done to maintain compatibility
with older kernels.
dt-bindings: Document correct and deprecated vendor-prefix with device isl29028
This patch documents the device isl29028 with its vendor-prefix. Undocumented deprecated vendor-prefix
found by checkpatch also documented for compatibility reasons.
Matthias Klein [Thu, 20 Nov 2014 10:52:45 +0000 (10:52 +0000)]
ARM: bcm2835: Add device tree for Raspberry Pi model B+
The model B and B+ differ in the GPIO lines for ACT and PWR leds, and the
I2S interface.
Signed-off-by: Matthias Klein <matthias.klein@linux.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 19 Nov 2014 22:19:17 +0000 (23:19 +0100)]
Merge tag 'mvebu-dt-3.19' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu DT changes for v3.19" from Jason Cooper:
- mvebu
- ReadyNAS 102 leds, esata
- ReadyNAS 2120 esata
- Add cache-unified for Aurora L2 node
- Add ref clk for timer and watchdog on Armada 375
- Cleanup Armada XP pinctrl for GigE
- Add RGMII pinctrl, i2c eeprom, and fix 74hc595 counter on Lenovo ix4-300d
- kirkwood
- Add DLink DIR665 and it's DSA configuration
* tag 'mvebu-dt-3.19' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-xp: Fix 74hc595 count for Lenovo ix4-300d
ARM: mvebu: armada-xp: Add I2C eeprom on Lenovo ix4-300d
ARM: mvebu: armada-xp: Add RGMII pinctrl to Lenovo ix4-300d
ARM: mvebu: armada-xp: Add GE0 pinctrl settings for GMII
ARM: mvebu: armada-xp: Move GE0/1 pinctrl settings for RGMII
ARM: mvebu: armada-xp: Use pinctrl node alias
ARM: mvebu: armada-xp: Add node alias to pinctrl and add base address
ARM: mvebu: armada-xp: Consolidate pinctrl node
ARM: Kirkwood: DIR665: Instantiate Distributed Switch Architecture
ARM: Kirkwood: Add support for DLink DIR665
ARM: mvebu: Enable rear eSATA ports of NETGEAR ReadyNAS 2120
ARM: mvebu: Enable the reference clock for timer and watchdog on Armada 375 SoC
arm: mvebu: Clarify (e)SATA ports info in NETGEAR ReadyNAS 102 .dts file
arm: mvebu: Fix LED color in NETGEAR ReadyNAS 102 .dts file
ARM: mvebu: Fix the Aurora L2 cache node with the required cache-unified property
Arnd Bergmann [Wed, 19 Nov 2014 22:11:12 +0000 (23:11 +0100)]
Merge tag 'hix5hd2-dt-for-3.19' of git://github.com/hisilicon/linux-hisi into next/dt
Pull "ARM: DT: Hisilicon terminal SoC HiX5HD2 DT updates for 3.19" from Wei Xu:
- Add reboot node, reusing syscon-reboot
- Add I2C nodes Hisilicon IP
- Add IR node based on Hisilicon IP
- Add Watchdog node based on ARM IP
- Add GPIO nodes based on ARM GPIO IP
- Add SATA node based on Hisilicon IP
- Add USB nodes
- Add MMC nodes based on Synopsys IP
- Add GMAC nodes based on Hisilicon IP
Arnd Bergmann [Wed, 19 Nov 2014 21:49:32 +0000 (22:49 +0100)]
Merge tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Third Round of Renesas ARM Based SoC DT Cleanups for v3.19" from Simon Horman:
* Use keyboard as gpio-keys node name
* tag 'renesas-dt-cleanups3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference: Use keyboard as gpio-keys node name
ARM: shmobile: koelsch: Use keyboard as gpio-keys node name
ARM: shmobile: lager: Use keyboard as gpio-keys node name
ARM: shmobile: armadillo800eva: Use keyboard as gpio-keys node name
Arnd Bergmann [Wed, 19 Nov 2014 21:45:33 +0000 (22:45 +0100)]
Merge tag 'renesas-dt-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v3.19" from Simon Horman:
* Add Add SoC-specific SATA compatible property to r8a7779
* Enable DMA for MMCIF on r8a7791 and r8a7790
* Enable USB-PHY, HS-USB and USB3.0 on r8a7791 and r8a7790
* Enable TMU timer via DT on r8a7778
* Enable CMT timer via DT on r8a73a4
* Add MMP and {SR}GX clocks to r8a7791 and r8a7790
* Correct scifa2 clock index on r8a7740
* Add missing INTCA for irqpin on r8a7740
The IIC nodes used the generic compatible properties only.
This causes the driver to fail when using Standard Speed, as the
operational clock is driven by the 104 MHz HP clock:
i2c-sh_mobile e6820000.i2c: timing values out of range: L/H=0x208/0x1bf
i2c-sh_mobile: probe of e6820000.i2c failed with error -22
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IIC nodes used the generic compatible properties only.
This may cause the driver to fail when using Standard Speed on IIC
masters where the operational clock is driven by the 130 MHz HP clock.
Add the SoC-specific compatible property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: koelsch: fixup I2C2 clock frequency
Current Koelsch I2C2 has 400kHz settings,
but, ak4643 audio codec chip which is connected to I2C2 can't
work such frequency.
Fixup I2C2 clock frequency to 100kHz.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds nodes describing the Marvell Berlin BG2CD USB PHY and USB. The BG2CD
SoC has 2 USB ChipIdea controllers, with usb0 host-only and usb1 dual-role
capable.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
projects / kernel.git / log