As was documented in commit e711c758629b ("pwm: sifive: Reduce time the
controller lock is held") a caller of pwm_sifive_update_clock() must
hold the mutex. So fix pwm_sifive_clock_notifier() to grab the lock.
While this necessity was only documented later, the race exists since
the driver was introduced.
Fixes: 144f67265c18 ("pwm: sifive: Add a driver for SiFive SoC PWM") Reported-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Link: https://lore.kernel.org/r/20221018061656.1428111-1-u.kleine-koenig@pengutronix.de Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In check_all_cpu_dscr_defaults, opendir() opens the directory stream.
Add missing closedir() in the error path to release it.
In check_cpu_dscr_default, open() creates an open file descriptor.
Add missing close() in the error path to release it.
Fixes: 2751660627ed ("selftests/powerpc: Add test for all DSCR sysfs interfaces") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221205084429.570654-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on getPerfCountInfo v1.018 documentation, some of the
hv_gpci events were deprecated for platform firmware that
supports counter_info_version 0x8 or above.
Fix the hv_gpci event list by adding a new attribute group
called "hv_gpci_event_attrs_v6" and a "ENABLE_EVENTS_COUNTERINFO_V6"
macro to enable these events for platform firmware
that supports counter_info_version 0x6 or below. And assigning
the hv_gpci event list based on output counter info version
of underlying plaform.
If platform_device_add() is not called or failed, it can not call
platform_device_del() to clean up memory, it should call
platform_device_put() in error case.
Fixes: 4432747d5443 ("[POWERPC] fsl_soc: add support for fsl_spi") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221029111626.429971-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The interrupt frame detection and loads from the hypothetical pt_regs
are not bounds-checked. The next-frame validation only bounds-checks
STACK_FRAME_OVERHEAD, which does not include the pt_regs. Add another
test for this.
The user could set r1 to be equal to the address matching the first
interrupt frame - STACK_INT_FRAME_SIZE, which is in the previous page
due to the kernel redzone, and induce the kernel to load the marker from
there. Possibly this could cause a crash at least. If the user could
induce the previous page to contain a valid marker, then it might be
able to direct perf to read specific memory addresses in a way that
could be transmitted back to the user in the perf data.
of_get_next_parent() returns a node pointer with refcount incremented,
we should use of_node_put() on it when not need anymore.
This function only calls of_node_put() in normal path,
missing it in the error path.
Add missing of_node_put() to avoid refcount leak.
Fixes: faadd32ed68b ("cxl: Add psl9 specific code") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Acked-by: Andrew Donnellan <ajd@linux.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220605060038.62217-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Afer commit 13e0419aca34 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically. It
needs to be freed when of_device_register() fails. Call put_device() to
give up the reference that's taken in device_initialize(), so that it
can be freed in kobject_cleanup() when the refcount hits 0.
macio device is freed in macio_release_dev(), so the kfree() can be
removed.
Fixes: 13e0419aca34 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221104032551.1075335-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The fsl_pamu_probe() returns directly when create_csd() failed, leaving
irq and memories unreleased.
Fix by jumping to error if create_csd() returns error.
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it before returning from ppr_notifier()
to avoid refcount leak.
If the alarms are disabled the topmost bit (AEN_*) is set in the alarm
registers. This is also interpreted in BCD number leading to this warning:
rtc rtc0: invalid alarm value: 2022-09-21T80:80:80
Fix this by masking alarm enabling and reserved bits.
On an iMX6ULL the following message appears when a wakealarm is set:
echo 0 > /sys/class/rtc/rtc1/wakealarm
rtc rtc1: Timeout trying to get valid LPSRT Counter read
This does not always happen but is reproducible quite often (7 out of 10
times). The problem appears because the iMX6ULL is not able to read the
registers within one 32kHz clock cycle which is the base clock of the
RTC. Therefore, this patch allows a difference of up to 320 cycles
(10ms). 10ms was chosen to be big enough even on systems with less cpu
power (e.g. iMX6ULL). According to the reference manual a difference is
fine:
- If the two consecutive reads are similar, the value is correct.
The values have to be similar, not equal.
Fixes: a740bdc28b20 ("rtc: snvs: Add timeouts to avoid kernel lockups") Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Francesco Dolcini <francesco@dolcini.it> Link: https://lore.kernel.org/r/20221106115915.7930-1-francesco@dolcini.it Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2f41fd3bc345 ("include/uapi/linux/byteorder, swab: force inlining
of some byteswap operations") added __always_inline to swab functions
and commit 8d232afb5dd8 ("uapi/linux/stddef.h: Provide __always_inline to
userspace headers") added a definition of __always_inline for use in
exported headers when the kernel's compiler.h is not available.
However, since swab.h does not include stddef.h, if the header soup does
not indirectly include it, the definition of __always_inline is missing,
resulting in a compilation failure, which was observed compiling the
perf tool using exported headers containing this commit:
In file included from /usr/include/linux/byteorder/little_endian.h:12:0,
from /usr/include/asm/byteorder.h:14,
from tools/include/uapi/linux/perf_event.h:20,
from perf.h:8,
from builtin-bench.c:18:
/usr/include/linux/swab.h:160:8: error: unknown type name `__always_inline'
static __always_inline __u16 __swab16p(const __u16 *p)
Fix this by replacing the inclusion of linux/compiler.h with
linux/stddef.h to ensure that we pick up that definition if required,
without relying on it's indirect inclusion. compiler.h is then included
indirectly, via stddef.h.
Fixes: 8d232afb5dd8 ("uapi/linux/stddef.h: Provide __always_inline to userspace headers") Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Petr Vaněk <arkamar@atlas.cz> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous build fix left a remaining issue in configurations with
64-bit dma_addr_t on 32-bit architectures:
drivers/infiniband/sw/siw/siw_qp_tx.c: In function 'siw_get_pblpage':
drivers/infiniband/sw/siw/siw_qp_tx.c:32:37: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
32 | return virt_to_page((void *)paddr);
| ^
Use the same double cast here that the driver uses elsewhere to convert
between dma_addr_t and void*.
Fixes: 4967ea83c16a ("RDMA/siw: Pass a pointer to virt_to_page()") Link: https://lore.kernel.org/r/20221215170347.2612403-1-arnd@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Bernard Metzler <bmt@zurich.ibm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
when kmalloc() fail to allocate memory in kasprintf(), propname
will be NULL, strcmp() called by of_get_property() will cause
null pointer dereference.
So return ENOMEM if kasprintf() return NULL pointer.
Fixes: fd7ec456301d ("power: supply: core: Add some helpers to use the battery OCV capacity table") Signed-off-by: ruanjinjie <ruanjinjie@huawei.com> Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ssi_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
ssi_pdriver is not unregistered.
Fix by unregister ssi_pdriver when the last platform_driver_register()
failed.
Fixes: 149a91e7d758 ("HSI: omap_ssi: built omap_ssi and omap_ssi_port into one module") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf doesn't provide proper symbol information for specially crafted
.debug files.
Sometimes .debug file may not have similar program header as runtime
ELF file. For example if we generate .debug file using objcopy
--only-keep-debug resulting file will not contain .text, .data and
other runtime sections. That means corresponding program headers will
have zero FileSiz and modified Offset.
Example: program header of text section of libxxx.so:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x00000000003d3000 0x00000000003d3000 0x00000000003d3000
0x000000000055ae80 0x000000000055ae80 R E 0x1000
Same program header after executing:
objcopy --only-keep-debug libxxx.so libxxx.so.debug
LOAD 0x0000000000001000 0x00000000003d3000 0x00000000003d3000
0x0000000000000000 0x000000000055ae80 R E 0x1000
Offset and FileSiz have been changed.
Following formula will not provide correct value, if program header
taken from .debug file (syms_ss):
sym.st_value -= phdr.p_vaddr - phdr.p_offset;
Correct program header information is located inside runtime ELF
file (runtime_ss).
Fixes: d800d31141cb9fcb ("perf symbol: Correct address for bss symbols") Signed-off-by: Ajay Kaher <akaher@vmware.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Makhalov <amakhalov@vmware.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Srivatsa S. Bhat <srivatsab@vmware.com> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Vasavi Sirnapalli <vsirnapalli@vmware.com> Link: http://lore.kernel.org/lkml/1669198696-50547-1-git-send-email-akaher@vmware.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On Arm64 a case is perf tools fails to find the corresponding trace
point folder for system calls listed in the table 'syscalltbl_arm64',
e.g. the generated system call table contains "lookup_dcookie" but we
cannot find out the matched trace point folder for it.
We need to figure out if there have any issue for the generated system
call table, on the other hand, we need to handle the case when trace
point folder is missed under sysfs, this patch sets the flag
syscall::nonexistent as true and returns the error from
trace__read_syscall_info().
Another problem is for trace__syscall_info(), it returns two different
values if a system call doesn't exist: at the first time calling
trace__syscall_info() it returns NULL when the system call doesn't exist,
later if call trace__syscall_info() again for the same missed system
call, it returns pointer of syscall. trace__syscall_info() checks the
condition 'syscalls.table[id].name == NULL', but the name will be
assigned in the first invoking even the system call is not found.
So checking system call's name in trace__syscall_info() is not the right
thing to do, this patch simply checks flag syscall::nonexistent to make
decision if a system call exists or not, finally trace__syscall_info()
returns the consistent result (NULL) if a system call doesn't existed.
Fixes: 01d3778a568a8f3e ("perf trace: Mark syscall ids that are not allocated to avoid unnecessary error messages") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: bpf@vger.kernel.org Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20221121075237.127706-4-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch defines a macro RAW_SYSCALL_ARGS_NUM to replace the open
coded number '6'.
Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: bpf@vger.kernel.org Link: https://lore.kernel.org/r/20221121075237.127706-2-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed") Signed-off-by: Sasha Levin <sashal@kernel.org>
This will go from a string to a number, so that filter expressions can
be constructed with strings and then, before applying the tracepoint
filters (or eBPF, in the future) we can map those strings to numbers.
The first one will be for 'msr' tracepoint arguments, but real quickly
we will be able to reuse all strarrays for that.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Brendan Gregg <brendan.d.gregg@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-wgqq48agcgr95b8dmn6fygtr@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed") Signed-off-by: Sasha Levin <sashal@kernel.org>
For instance 'msr' appears in several tracepoints, so we can associate
it with a single scnprintf() routine auto-generated from kernel headers,
as will be done in followup patches.
Start with an empty array of associations.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-89ptht6s5fez82lykuwq1eyb@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed") Signed-off-by: Sasha Levin <sashal@kernel.org>
So that the scnprintf beautifiers can access it, as will be the case
with the char array one in the following csets, that needs to know
the number of elements in an array.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-01qmjqv6cb1nj1qy4khdexce@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed") Signed-off-by: Sasha Levin <sashal@kernel.org>
We set the default scnprint routines for the syscall args based on its
type or on heuristics based on its names, now we'll use this for
tracepoints as well, so move it out of syscall__set_arg_fmts() and into
a routine that receive just an array of syscall_arg_fmt entries + the
tracepoint format fields list.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-xs3x0zzyes06c7scdsjn01ty@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed") Signed-off-by: Sasha Levin <sashal@kernel.org>
As this has all the things needed to format tracepoints events, not just
syscalls, that, after all, are just tracepoints with a set in stone ABI,
i.e. order and number of parameters.
For tracepoints we'll create a
static struct syscall_fmt tracepoint_fmts[]
array and will fill the ->arg[] entries with the beautifier for each
positional argument and record the name, then, when we need it, we'll
just check that the position has the same name, maybe even type, so that
we can do some check that the tracepoint hasn't changed, if it has, we
can even reorder things.
Keep calling it syscall_fmt but use it as well for tracepoints, do it
this way to minimize changes and reuse what is in place for syscalls,
we'll see.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-2x1jgiev13zt4njaanlnne0d@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: 03e9a5d8eb55 ("perf trace: Handle failure when trace point folder is missed") Signed-off-by: Sasha Levin <sashal@kernel.org>
When a system call is not detected, the reason is either because the
system call ID is out of scope or failure to find the corresponding path
in the sysfs, trace__read_syscall_info() returns zero. Finally, without
returning an error value it introduces confusion for the caller.
This patch lets the function trace__read_syscall_info() to return
-EEXIST when a system call doesn't exist.
Fixes: 01d3778a568a8f3e ("perf trace: Mark syscall ids that are not allocated to avoid unnecessary error messages") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: bpf@vger.kernel.org Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20221121075237.127706-3-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_add() succeeds, we should call device_del() when want to
get rid of it, so move it into proper jump symbol.
Otherwise, when __power_supply_register() returns fail and goto
wakeup_init_failed to exit, there is still residue device file in sysfs.
When attempt to probe device again, sysfs would complain as below:
If ssi_add_controller() returns error, it should call hsi_put_controller()
to give up the reference that was set in hsi_alloc_controller(), so that
it can call hsi_controller_release() to free controller and ports that
allocated in hsi_alloc_controller().
Fixes: f6a17db405d3 ("HSI: Introduce OMAP SSI driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful uvesafb_init_mtrr() call, it must be
undone by a corresponding arch_phys_wc_del() call, as already done in the
remove function.
This has been added in the remove function in commit aa4c8c53c884
("uvesafb: Clean up MTRR code")
pci_get_device() will increase the reference count for the returned
pci_dev. For the error path, we need to use pci_dev_put() to decrease
the reference count.
Only a single out of three devices need a PWM, so from driver it's
optional. Moreover it's a single driver in the entire kernel that
currently selects PWM. Unfortunately this selection is a root cause
of the circular dependencies when we want to enable optional PWM
for some other drivers that select GPIOLIB.
Fixes: 5273cb8dd047 ("drivers/video: add support for the Solomon SSD1307 OLED Controller") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When input some constructed invalid 'trigger' command, command info
in 'error_log' are lost [1].
The root cause is that there is a path that event_hist_trigger_parse()
is recursely called once and 'last_cmd' which save origin command is
cleared, then later calling of hist_err() will no longer record origin
command info:
event_hist_trigger_parse() {
last_cmd_set() // <1> 'last_cmd' save origin command here at first
create_actions() {
onmatch_create() {
action_create() {
trace_action_create() {
trace_action_create_field_var() {
create_field_var_hist() {
event_hist_trigger_parse() { // <2> recursely called once
hist_err_clear() // <3> 'last_cmd' is cleared here
}
hist_err() // <4> No longer find origin command!!!
Since 'glob' is empty string while running into the recurse call, we
can trickly check it and bypass the call of hist_err_clear() to solve it.
[1]
# cd /sys/kernel/tracing
# echo "my_synth_event int v1; int v2; int v3;" >> synthetic_events
# echo 'hist:keys=pid' >> events/sched/sched_waking/trigger
# echo "hist:keys=next_pid:onmatch(sched.sched_waking).my_synth_event(\
pid,pid1)" >> events/sched/sched_switch/trigger
# cat error_log
[ 8.405018] hist:sched:sched_switch: error: Couldn't find synthetic event
Command:
hist:keys=next_pid:onmatch(sched.sched_waking).my_synth_event(pid,pid1)
^
[ 8.816902] hist:sched:sched_switch: error: Couldn't find field
Command:
hist:keys=next_pid:onmatch(sched.sched_waking).my_synth_event(pid,pid1)
^
[ 8.816902] hist:sched:sched_switch: error: Couldn't parse field variable
Command:
hist:keys=next_pid:onmatch(sched.sched_waking).my_synth_event(pid,pid1)
^
[ 8.999880] : error: Couldn't find field
Command:
^
[ 8.999880] : error: Couldn't parse field variable
Command:
^
[ 8.999880] : error: Couldn't find field
Command:
^
[ 8.999880] : error: Couldn't create histogram for field
Command:
^
The skb is delivered to netif_rx() in rtllib_monitor_rx(), which may free it,
after calling this, dereferencing skb may trigger use-after-free.
Found by Smatch.
Fixes: cc5d857430c2 ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20221123081253.22296-1-yuehaibing@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While doing fault injection test, I got the following report:
------------[ cut here ]------------
kobject: '(null)' (0000000039956980): is not initialized, yet kobject_put() is being called.
WARNING: CPU: 3 PID: 6306 at kobject_put+0x23d/0x4e0
CPU: 3 PID: 6306 Comm: 283 Tainted: G W 6.1.0-rc2-00005-g307c1086d7c9 #1253
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:kobject_put+0x23d/0x4e0
Call Trace:
<TASK>
cdev_device_add+0x15e/0x1b0
__iio_device_register+0x13b4/0x1af0 [industrialio]
__devm_iio_device_register+0x22/0x90 [industrialio]
max517_probe+0x3d8/0x6b4 [max517]
i2c_device_probe+0xa81/0xc00
When device_add() is injected fault and returns error, if dev->devt is not set,
cdev_add() is not called, cdev_del() is not needed. Fix this by checking dev->devt
in error path.
Fixes: 286719f21b1c ("chardev: add helper function to register char devs with a struct device") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221202030237.520280-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If mcb_device_register() returns error in chameleon_parse_gdd(), the refcount
of bus and device name are leaked. Fix this by calling put_device() to give up
the reference, so they can be released in mcb_release_dev() and kobject_cleanup().
Fixes: 60a91070ad8b ("drivers: Introduce MEN Chameleon Bus") Reviewed-by: Johannes Thumshirn <jth@kernel.org> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Johannes Thumshirn <jth@kernel.org> Link: https://lore.kernel.org/r/ebfb06e39b19272f0197fa9136b5e4b6f34ad732.1669624063.git.johannes.thumshirn@wdc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failing to allocate report_desc, opts->refcnt has already been
incremented so it needs to be decremented to avoid leaving the options
structure permanently locked.
Fixes: d8887b75f017 ("usb: gadget: hid: add configfs support") Tested-by: Lee Jones <lee@kernel.org> Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Reviewed-by: Lee Jones <lee@kernel.org> Signed-off-by: John Keeping <john@metanate.com> Link: https://lore.kernel.org/r/20221122123523.3068034-3-john@metanate.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The embedded struct cdev does not have its lifetime correctly tied to
the enclosing struct f_hidg, so there is a use-after-free if /dev/hidgN
is held open while the gadget is deleted.
This can readily be replicated with libusbgx's example programs (for
conciseness - operating directly via configfs is equivalent):
Pull the existing device up in to struct f_hidg and make use of the
cdev_device_{add,del}() helpers. This changes the lifetime of the
device object to match struct f_hidg, but note that it is still added
and deleted at the same time.
Fixes: 4ad382e8ded2 ("USB: gadget: add HID gadget driver") Tested-by: Lee Jones <lee@kernel.org> Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Reviewed-by: Lee Jones <lee@kernel.org> Signed-off-by: John Keeping <john@metanate.com> Link: https://lore.kernel.org/r/20221122123523.3068034-2-john@metanate.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
f_hid provides the OUT Endpoint as only way for receiving reports
from the host. SETUP/SET_REPORT method is not supported, and this causes
a number of compatibility problems with various host drivers, especially
in the case of keyboard emulation using f_hid.
- Some hosts do not support the OUT Endpoint and ignore it,
so it becomes impossible for the gadget to receive a report
from the host. In the case of a keyboard, the gadget loses
the ability to receive the status of the LEDs.
- Some BIOSes/UEFIs can't work with HID devices with the OUT Endpoint
at all. This may be due to their bugs or incomplete implementation
of the HID standard.
For example, absolutely all Apple UEFIs can't handle the OUT Endpoint
if it goes after IN Endpoint in the descriptor and require the reverse
order (OUT, IN) which is a violation of the standard.
Other hosts either do not initialize gadgets with a descriptor
containing the OUT Endpoint completely (like some HP and DELL BIOSes
and embedded firmwares like on KVM switches), or initialize them,
but will not poll the IN Endpoint.
This patch adds configfs option no_out_endpoint=1 to disable
the OUT Endpoint and allows f_hid to receive reports from the host
via SETUP/SET_REPORT.
Previously, there was such a feature in f_hid, but it was replaced
by the OUT Endpoint [1] in the commit faf280c6cd0f ("usb: gadget: hidg:
register OUT INT endpoint for SET_REPORT"). So this patch actually
returns the removed functionality while making it optional.
For backward compatibility reasons, the OUT Endpoint mode remains
the default behaviour.
- The OUT Endpoint mode provides the report queue and reduces
USB overhead (eliminating SETUP routine) on transmitting a report
from the host.
- If the SETUP/SET_REPORT mode is used, there is no report queue,
so the userspace will only read last report. For classic HID devices
like keyboards this is not a problem, since it's intended to transmit
the status of the LEDs and only the last report is important.
This mode provides better compatibility with strange and buggy
host drivers.
Both modes passed USBCV tests. Checking with the USB protocol analyzer
also confirmed that everything is working as it should and the new mode
ensures operability in all of the described cases.
The ARR (auto reload register) and CMP (compare) registers are
successively written. The status bits to check the update of these
registers are polled together with regmap_read_poll_timeout().
The condition to end the loop may become true, even if one of the register
isn't correctly updated.
So ensure both status bits are set before clearing them.
Fixes: 9650c30dc4ce ("iio: counter: Add support for STM32 LPTimer") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Link: https://lore.kernel.org/r/20221123133609.465614-1-fabrice.gasnier@foss.st.com/ Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() fails in cxl_pci_afu|adapter(), the device
is not added, device_unregister() can not be called in the error
path, otherwise it will cause a null-ptr-deref because of removing
not added device.
As comment of device_register() says, it should use put_device() to give
up the reference in the error path. So split device_unregister() into
device_del() and put_device(), then goes to put dev when register fails.
Fixes: 1566e6cae6b8 ("cxl: Driver code for powernv PCIe based cards for userspace access") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Frederic Barrat <fbarrat@linux.ibm.com> Acked-by: Andrew Donnellan <ajd@linux.ibm.com> Link: https://lore.kernel.org/r/20221111145440.2426970-2-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() fails in cxl_register_afu|adapter(), the device
is not added, device_unregister() can not be called in the error path,
otherwise it will cause a null-ptr-deref because of removing not added
device.
As comment of device_register() says, it should use put_device() to give
up the reference in the error path. So split device_unregister() into
device_del() and put_device(), then goes to put dev when register fails.
In some bad situation, the gts may be freed gru_check_chiplet_assignment.
The call chain can be gru_unload_context->gru_free_gru_context->gts_drop
and kfree finally. However, the caller didn't know if the gts is freed
or not and use it afterwards. This will trigger a Use after Free bug.
Fix it by introducing a return value to see if it's in error path or not.
Free the gts in caller if gru_check_chiplet_assignment check failed.
If device_register() returns error in ocxl_file_register_afu(),
the name allocated by dev_set_name() need be freed. As comment
of device_register() says, it should use put_device() to give
up the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanup(),
and info is freed in info_release().
Fixes: bd3d953fe88e ("ocxl: Create a clear delineation between ocxl backend & frontend") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Andrew Donnellan <ajd@linux.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.ibm.com> Link: https://lore.kernel.org/r/20221111145929.2429271-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sunsab_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
allocated sunsab_ports is leaked.
Fix by free sunsab_ports and set it to NULL when platform_driver_register()
failed.
Since altera_uart_interrupt() may also be called from
a poll timer in "serving_softirq" context, use
spin_[lock_irqsave|unlock_irqrestore] variants, which
are appropriate for both softirq and hardware interrupt
contexts.
Fixes: 410f78e97a5b ("altera_uart: Add support for polling mode (IRQ-less)") Signed-off-by: Gabriel Somlo <gsomlo@gmail.com> Link: https://lore.kernel.org/r/20221122200426.888349-1-gsomlo@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "stop TX" path in altera_uart_tx_chars() is open-coded, so:
* use uart_circ_empty() to check if the buffer is empty, and
* when true, call altera_uart_stop_tx().
As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083b901f001794038a08b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
The 'fwnode' set in tcpci_parse_config() which is called
in tcpci_register_port(), its node refcount is increased
in device_get_named_child_node(). It needs be put while
exiting, so call fwnode_handle_put() in the error path of
tcpci_register_port() and in tcpci_unregister_port() to
avoid leak.
Fixes: 97f6c47d76de ("usb: typec: add fwnode to tcpc") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221121062416.1026192-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
typec_altmode_exit checks if ops->enter is not NULL but then calls
ops->exit a few lines below. Fix that and check for the function
pointer it's about to call instead.
Fixes: d4e63605a26c ("usb: typec: Bus type for alternate modes") Signed-off-by: Sven Peter <sven@svenpeter.dev> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221114165924.33487-1-sven@svenpeter.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/staging/vme_user/vme_tsi148.c:1757 tsi148_dma_list_add() warn:
'&entry->list' not removed from list
In tsi148_dma_list_add(), the error path "goto err_dma" will not
remove entry->list from list->entries, but entry will be freed,
then list traversal may cause UAF.
Fix by removeing it from list->entries before free().
The code in the FOTG210 driver isn't entirely endianness-agnostic
as reported by the kernel robot sparse testing. This came to
the surface while moving the files around.
The driver is only used on little-endian systems, so this causes
no real-world regression, but it is nice to be strict and have
some compile coverage also on big endian machines, so fix it
up with the right LE accessors.
This fixes a concurrency issue addressed in commit 8e073d39ef1f ("UIO: Fix
concurrency issue"):
"In a SMP case there was a race condition issue between
Uio_pdrv_genirq_irqcontrol() running on one CPU and irq handler on
another CPU. Fix it by spin_locking shared resources access inside irq
handler."
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
merged, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(), thus, both had the same concurrency issue
mentioned by the above commit. However, the above patch was only applied to
the "uio_pdrv_genirq" driver.
Split out from commit 8e073d39ef1f ("UIO: Fix concurrency issue").
Fixes: 5c6915d927a9 ("Add new uio device for dynamic memory allocation") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-3-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2afb03a5503a ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 8e073d39ef1f ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-while-atomic bug that commit 2afb03a5503a ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") was trying to
fix. Thus, this fixes the missing unlock in irqcontrol() by importing the
implementation of irqcontrol() handler from the "uio_pdrv_genirq" driver.
In the end, it reverts commit 2afb03a5503a ("uio: fix a
sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") and change
disable_irq() to disable_irq_nosync().
It is worth noting that this still does not address the concurrency issue
fixed by commit 8e073d39ef1f ("UIO: Fix concurrency issue"). It will be
addressed separately in the next commits.
Split out from commit 8e073d39ef1f ("UIO: Fix concurrency issue").
Fixes: 2afb03a5503a ("uio: fix a sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Link: https://lore.kernel.org/r/20220930224100.816175-2-rafaelmendsr@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If class_add_groups() returns error, the 'cp->subsys' need be
unregister, and the 'cp' need be freed.
We can not call kset_unregister() here, because the 'cls' will
be freed in callback function class_release() and it's also
freed in caller's error path, it will cause double free.
So fix this by calling kobject_del() and kfree_const(name) to
cleanup kobject. Besides, call kfree() to free the 'cp'.
This allows DMA engine to go into runtime-suspended mode whenever there is
no data to receive, instead of keeping DMA active all the time while TTY
is opened (i.e. permanently active in practice, like in the case of UART
Bluetooth).
If device_register() returns error, the 'dev' and name needs be
freed. Add a release function, and then call put_device() in the
error path, so the name is freed in kobject_cleanup() and to the
'dev' is freed in release function.
Fixes: 33dc8269f10b ("m68k: dio - Kill warn_unused_result warnings") Fixes: 13e0419aca34 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109064036.1835346-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2 ways to create IPoIB PKEY child interfaces:
1) Writing a PKEY to /sys/class/net/<ib parent interface>/create_child.
2) Using netlink with iproute.
While with sysfs the child interface has the same number of tx and
rx queues as the parent, with netlink there will always be 1 tx
and 1 rx queue for the child interface. That's because the
get_num_tx/rx_queues() netlink ops are missing and the default value
of 1 is taken for the number of queues (in rtnl_create_link()).
This change adds the get_num_tx/rx_queues() ops which allows for
interfaces with multiple queues to be created over netlink. This
constant only represents the max number of tx and rx queues on that
net device.
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path.
Fixes: 126ca0987fa0 ("[PATCH] Add Geode HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() for the normal and error path.
Fixes: baf5b739fb9c ("[PATCH] Add AMD HW RNG driver") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the previous iteration of the while loop, the "ret" may have been
assigned a value of 0, so the error return code -EINVAL may have been
incorrectly set to 0. To fix set valid return code before calling to
goto.
Fixes: 2569a67d5736 ("staging/rdma/hfi1: Tune for unknown channel if configuration file is absent") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Link: https://lore.kernel.org/r/1669953638-11747-1-git-send-email-wangyufen@huawei.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
omap_sham_probe() calls pm_runtime_get_sync() and calls
pm_runtime_put_sync() latter to put usage_counter. However,
pm_runtime_get_sync() will increment usage_counter even it failed. Fix
it by replacing it with pm_runtime_resume_and_get() to keep usage
counter balanced.
Fixes: e42aa6562662 ("crypto: omap-sham - Convert to use pm_runtime API") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Acked-by: Mark Greer <mgreer@animalcreek.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When f2fs chooses GC victim in large section & LFS mode,
next_victim_seg[gc_type] is referenced first. After segment is freed,
next_victim_seg[gc_type] has the next segment number.
However, next_victim_seg[gc_type] still has the last segment number
even after the last segment of section is freed. In this case, when f2fs
chooses a victim for the next GC round, the last segment of previous victim
section is chosen as a victim.
Initialize next_victim_seg[gc_type] to NULL_SEGNO for the last segment in
large section.
Fixes: afa16fea4b14 ("f2fs: support subsectional garbage collection") Signed-off-by: Yonggil Song <yonggil.song@samsung.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/scsi/snic/snic_disc.c:307 snic_tgt_create() warn:
'&tgt->list' not removed from list
If device_add() fails in snic_tgt_create(), tgt will be freed, but
tgt->list will not be removed from snic->disc.tgt_list, then list traversal
may cause UAF.
Remove from snic->disc.tgt_list before free().
Fixes: e9690ed37a04 ("snic: driver for Cisco SCSI HBA") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Link: https://lore.kernel.org/r/20221117035100.2944812-1-cuigaosheng1@huawei.com Acked-by: Narsimhulu Musini <nmusini@cisco.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fcoe_init() calls fcoe_transport_attach(&fcoe_sw_transport), but when
fcoe_if_init() fails, &fcoe_sw_transport is not detached and leaves freed
&fcoe_sw_transport on fcoe_transports list. This causes panic when
reinserting module.
BUG: unable to handle page fault for address: fffffbfff82e2213
RIP: 0010:fcoe_transport_attach+0xe1/0x230 [libfcoe]
Call Trace:
<TASK>
do_one_initcall+0xd0/0x4e0
load_module+0x5eee/0x7210
...
Fixes: 5f67c11dadd8 ("[SCSI] fcoe: convert fcoe.ko to become an fcoe transport provider driver") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221115092442.133088-1-chenzhongjin@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipr_init() will not call unregister_reboot_notifier() when
pci_register_driver() fails, which causes a WARNING. Call
unregister_reboot_notifier() when pci_register_driver() fails.
If device_register() returns an error, the name allocated by dev_set_name()
needs to be freed. As the comment of device_register() says, one should use
put_device() to give up the reference in the error path. Fix this by
calling put_device(), then the name can be freed in kobject_cleanup().
The 'fcf' is freed in fcoe_fcf_device_release(), so the kfree() in the
error path can be removed.
The 'ctlr' is freed in fcoe_ctlr_device_release(), so don't use the error
label, just return NULL after calling put_device().
Fixes: 679bdc185b60 ("[SCSI] libfcoe: Add fcoe_sysfs") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221112094310.3633291-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_rphy() returns an error, the 'rphy' allocated in
sas_end_device_alloc() needs to be freed. Address this by calling
sas_rphy_free() in the error path.
Fixes: df582937d01b ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221111043012.1074466-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If hpsa_sas_port_add_phy() returns an error, hpsa_free_sas_phy() can not be
called to free the memory because the port and the phy have not been added
yet.
Replace hpsa_free_sas_phy() with sas_phy_free() and kfree() to avoid kernel
crash in this case.
Fixes: df582937d01b ("hpsa: add in sas transport class") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221110151129.394389-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mpt3sas_transport_port_add(), if sas_rphy_add() returns error,
sas_rphy_free() needs be called to free the resource allocated in
sas_end_device_alloc(). Otherwise a kernel crash will happen:
Because transport_add_device() is not called when sas_rphy_add() fails, the
device is not added. When sas_rphy_remove() is subsequently called to
remove the device in the remove() path, a NULL pointer dereference happens.
Fixes: a1a99f1e639f ("[SCSI] mpt3sas: add new driver supporting 12GB SAS") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109032403.1636422-1-yangyingliang@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the past, the data for mb-skcipher test has been allocated
twice, that means the first allcated memory area is without
free, which may cause a potential memory leakage. So this
patch is to remove one allocation to fix this error.
The hpda_alloc_ctlr_info() allocates h and its field reply_map. However, in
hpsa_init_one(), if alloc_percpu() failed, the hpsa_init_one() jumps to
clean1 directly, which frees h and leaks the h->reply_map.
Fix by calling hpda_free_ctlr_info() to release h->replay_map and h instead
free h directly.
Fixes: 55e95a1d412c ("scsi: hpsa: fix selection of reply queue") Signed-off-by: Yuan Can <yuancan@huawei.com> Link: https://lore.kernel.org/r/20221122015751.87284-1-yuancan@huawei.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pci_get_device() will increase the reference count for the returned
pci_dev, and also decrease the reference count for the input parameter
*from* if it is not NULL.
If we break out the loop in node_affinity_init() with 'dev' not NULL, we
need to call pci_dev_put() to decrease the reference count. Add missing
pci_dev_put() in error path.
Fixes: 2c3c1868f268 ("IB/hfi1: Invalid NUMA node information can cause a divide by zero") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Link: https://lore.kernel.org/r/20221117131546.113280-1-wangxiongfeng2@huawei.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to the way the hardware works, every double word in the SHA384 and
SHA512 larval hashes must be swapped. Currently this is done at run
time, during driver initialization.
However, this swapping can easily be done at build time. Treating each
double word as two words has the benefit of changing the larval hashes'
types from u64[] to u32[], like for all other hashes, and allows
dropping the casts and size doublings when calling cc_set_sram_desc().
If you try to allocate a memory larger than(>=) MAX_ORDER, then kmalloc()
will definitely fail. It creates a stack trace and messes up dmesg. The
user controls the size here so if they specify a too large size it will
fail.
Add __GFP_NOWARN in order to avoid too large allocation warning. This is
detected by static analysis using smatch.
Fixes: 3090fd30e9c6 ("scsi: scsi_debug: add resp_write_scat function") Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Link: https://lore.kernel.org/r/20221111100526.1790533-1-harshit.m.mogalapalli@oracle.com Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log